Garmin | GMA™ 35 | Garmin GMA™ 35 Instructions for Continued Airworthiness GTN 6XX/7XX – Bell 206L Series

Garmin GMA™ 35 Instructions for Continued Airworthiness GTN 6XX/7XX – Bell 206L Series
Instructions for Continued Airworthiness
GTN 6XX/7XX - Bell 206L Series
as installed in
Bell 206L Series
(Make and Model Aircraft)
Reg. No. ___________
S/N __________
Dwg. Number:
190-01007-K1 Rev. 2
Garmin International, Inc.
1200 E. 151st Street
Olathe, Kansas 66062 USA
Record of Revision
Rev.
Date
1
2
10/02/2013
03/22/2016
Description of Change
Initial Release
Added instructions to disable Airspace Altitude Labels
Company Proprietary Information
This drawing and the specifications contained herein are the property of Garmin International or its
subsidiaries and may not be reproduced or used in whole or in part as the basis for manufacture or sale
of products without written permission.
Copyright  2016 Garmin Ltd. or its subsidiaries. All rights reserved.
Garmin International, Inc.
1200 E. 151st Street
Olathe, Kansas 66062 U.S.A.
Page ii
Instructions for Continued Airworthiness GTN 6XX/7XX - Bell 206L Series
190-01007-K1 Rev. 2
Table of Contents
1.
2.
3.
INTRODUCTION ................................................................................................................................... 1
1.1
Purpose ......................................................................................................................................... 1
1.2
Scope ............................................................................................................................................ 1
1.3
Document Control ......................................................................................................................... 1
1.4
Permission to Use Certain Documents ......................................................................................... 1
1.5
Definitions ...................................................................................................................................... 1
1.6
Terminology................................................................................................................................... 2
INSTRUCTIONS FOR CONTINUED AIRWORTHINESS ..................................................................... 3
2.1
Introduction.................................................................................................................................... 3
2.2
Description of Alteration ................................................................................................................ 3
2.3
Control, Operating, and Testing Information ................................................................................. 4
2.4
Servicing Information .................................................................................................................... 4
2.5
Periodic Maintenance .................................................................................................................... 4
2.6
Troubleshooting Information ......................................................................................................... 9
2.7
Removal and Replacement Information ........................................................................................ 9
2.8
Diagrams ..................................................................................................................................... 17
2.9
Special Inspection Requirements................................................................................................ 17
2.10
Application of Protective Treatments .......................................................................................... 17
2.11
Data Relative to Structural Fasteners ......................................................................................... 17
2.12
Special Tools ............................................................................................................................... 17
2.13
Additional Instructions ................................................................................................................. 17
2.14
Overhaul Period .......................................................................................................................... 17
2.15
ICA Revision and Distribution ..................................................................................................... 17
2.16
Assistance ................................................................................................................................... 18
2.17
Implementation and Record Keeping .......................................................................................... 18
AIRWORTHINESS LIMITATIONS SECTION ..................................................................................... 19
APPENDIX A
EQUIPMENT LOCATIONS AND WIRE ROUTING ........................................................ 20
Table of Tables
Table 1. Maintenance Intervals for GTNs and GMA 35 ................................................................................ 4
Table 2. Maintenance Intervals for Antennas Replaced Under this STC ..................................................... 8
Table 3. Bill of Materials .............................................................................................................................. 12
Table 4. GTN Equipment Weight and Moment Arm ................................................................................... 16
Page iii
Instructions for Continued Airworthiness GTN 6XX/7XX - Bell 206L Series
190-01007-K1 Rev. 2
1.
INTRODUCTION
1.1 Purpose
This document provides Instructions for Continued Airworthiness compliant with requirements of 14 CFR
§27.1529, and Part 27 Appendix A. This ICA is to be used by the agency installing Garmin GTN 6XX/7XX
navigators, GMA 35 audio panel, and additional equipment under the GTN 6XX/7XX Part 27 Approved
Model List (AML) STC, and includes information required by the operator to adequately maintain installed
items.
1.2 Scope
This document provides the Instructions for Continued Airworthiness for Bell 206L series rotorcraft,
modified by the installation of the Garmin GTN 6XX/7XX and optional GMA 35 under the AML STC.
1.3 Document Control
This document shall be released, archived, and controlled in accordance with the Garmin document
control system. When this document is revised, refer to Section 2.15 for information on how to gain FAA
acceptance or approval and how to notify customers of changes.
1.4 Permission to Use Certain Documents
Permission is granted to any corporation or person applying for approval of a Garmin Instructions for
Continued Airworthiness GTN 6XX/7XX - Bell 206L Series to use and reference appropriate STC
documents to accomplish the Instructions for Continued Airworthiness and show compliance with STC
engineering data. This permission does not construe suitability of the documents. It is the responsibility of
the applicant to determine the suitability of the documents for the ICA.
1.5 Definitions
The following terminology is used within this document:
1)
2)
3)
4)
5)
6)
7)
8)
9)
10)
11)
12)
13)
14)
15)
16)
17)
Page 1 of 20
ACO: Aircraft Certification Office
AEG: Aircraft Evaluation Group
BIT:
Built-In Test
COM: Communications
CFR: Code of Federal Regulations
FAA: Federal Aviation Administration
GPS: Global Positioning System
ICA:
Instructions for Continued Airworthiness
LED: Light Emitting Diode
LRU: Line Replaceable Unit
NAV: Navigation
MFD: Multi-Function Display
PMI: Principal Maintenance Inspector
POI:
Principal Operations Inspector
STC: Supplemental Type Certificate
TSO: Technical Standard Order
WAAS: Wide Area Augmentation System
Instructions for Continued Airworthiness GTN 6XX/7XX - Bell 206L Series
190-01007-K1 Rev. 2
1.6 Terminology
Except where specifically noted, references made to the ‘GTN’ will equally apply to the GTN
625/635/650/725/750. Also, ‘GTN 7XX’ refers specifically to the GTN 725 and GTN 750, and ‘GTN 6XX’
refers specifically to the GTN 625, GTN 635, and GTN 650.
Also, except where specifically noted, references made to the ‘Bell 206L Series’ will apply equally to the
Bell 206L, Bell 206L3, and Bell 206L4.
Page 2 of 20
Instructions for Continued Airworthiness GTN 6XX/7XX - Bell 206L Series
190-01007-K1 Rev. 2
2.
INSTRUCTIONS FOR CONTINUED AIRWORTHINESS
2.1 Introduction
Content, Scope, Purpose and Arrangement: This document identifies the Instructions for Continued
Airworthiness for the modification of the aircraft by installation of
the Garmin GTN 6XX/7XX and GMA 35 Part 27 AML STC.
Applicability:
Applies to aircraft altered by installation of the Garmin 6XX/7XX
and GMA 35 Part 27 AML STC.
Definition of Abbreviations:
See Sections 1.5 and Section 1.6
Precautions:
None
Units of measurement:
None
Referenced publications:
(or their later revisions)
1) Garmin 190-01007-B1 Rev.1, “GTN 6XX/7XX Part 27 AML
STC System Maintenance Manual”
2) Garmin 190-01007-03 Rev. D, “GTN 725/750 Pilot’s Guide”
3) Garmin 190-01004-03 Rev. D, “GTN 625/635/650 Pilot’s
Guide”
4) Bell Model 206L Maintenance Manual, Bell Document BHT206L-MM, Revision 36, 1 June 2012
5) Bell Model 206L1 Maintenance Manual, Bell Document BHT206L1-MM, Revision 33, 1 June 2012
6) Bell Model 206L3 Maintenance Manual, Bell Document BHT206L3-MM, Revision 19, 1 June 2012
7) Bell Model 206L4 Maintenance Manual, Bell Document BHT206L4-MM, Revision 16, 1 June 2012
8) Structural Repair Manual for Bell Model 206 Series
Helicopters, BHT-206-SRM-1, Revision 1, April 1995
9) Electrical Standard Practices Manual for all Bell Helicopter
Commercial Products, BHT-ELEC-SPM, Revision 2, July
2012
Retention:
This document, or the information contained within, will be
included in the aircraft’s permanent records.
2.2 Description of Alteration
The GTN navigators are a family of aviation panel mounted retro-fit products. GTN units utilize a
touchscreen as the primary control interface. Traditional knobs and buttons have been minimized to
simplify access to the color multi-function display (MFD), NAV and COM transceiver, and GPS/WAAS
navigator functions.
The GTN 625/635/650 Navigators (Garmin Touch Navigation) are a family of 2.65-inch tall aviation panel
mounted retro-fit products that are intended to supersede the Garmin 400W Series Navigators. The GTN
6XX product family consists of the GTN 625 GPS/WAAS navigator, the GTN 635 GPS/WAAS/COM
navigator, and the GTN 650 GPS/WAAS/NAV/COM navigator.
The GTN 725/750 Navigators (Garmin Touch Navigation) are a family of 6.00-inch tall aviation panel
mounted retro-fit products that are intended to supersede the Garmin 500W Series Navigators. The GTN
7XX product family consists of the GTN 725 GPS/WAAS navigator, and the GTN 750
GPS/WAAS/NAV/COM navigator.
Page 3 of 20
Instructions for Continued Airworthiness GTN 6XX/7XX - Bell 206L Series
190-01007-K1 Rev. 2
The optional GMA 35 is an audio panel with a Marker Beacon receiver. The GMA 35 in conjunction with
a GTN 7XX provide full audio panel capability, for communication and navigation radios, headsets,
microphones, and speakers. The GMA 35 is mounted in a notch behind the GTN 7XX to free up mounting
space in the flight deck instrument panel.
The optional Vivisun HTAWS terrain caution/warning indicator and HTAWS status annunciation are
required for those installations that have the HTAWS function enabled on the GTN (unless the rotorcraft
is equipped with a GDU 620). These annunciators serve as the visual indication of a terrain/obstacle
caution or warning alert as well as HTAWS failure and HTAWS inhibit status.
2.3 Control, Operating, and Testing Information
See Garmin 190-01004-03 Rev. D, “GTN 625/635/650 Pilot’s Guide” and Garmin 190-01007-03 Rev. D,
“GTN 725/750 Pilot’s Guide” for information on how to operate the system in normal mode.
See the Section 3 of the GTN 6XX/7XX PART 27 AML STC SYSTEM MAINTENANCE MANUAL, Section
3 for details on how to operate and access configuration mode and diagnostic pages, and Section 2.1 for
document part numbers. See Section 6 for general ground checks and system test procedures
See GTN 6XX/7XX PART 27 AML STC MAINTENANCE MANUAL for a system description.
2.4 Servicing Information
None. In the event of system failure, troubleshoot the GTN 6XX/7XX and GMA 35 in accordance with
Section 4 of the GTN 6XX/7XX PART 27 AML STC SYSTEM MAINTENANCE MANUAL.
2.5 Periodic Maintenance
The GTN and GMA 35 are designed to detect internal failures. A thorough self-test is executed
automatically upon application of power to the units, and built-in tests (BIT) are continuously executed.
Detected errors are indicated as failure annunciations, system messages, or a combination of the two.
Operation of the GTN 6XX/7XX and GMA 35 is not permitted unless the inspections described in this
section have been completed within time intervals prescribed in Table 1. All antennas connected to the
GTN should be maintained in accordance with maintenance and inspection data appropriate for the
antenna installation.
Table 1. Maintenance Intervals for GTNs and GMA 35
Item
Description/Procedure
Interval
Equipment Removal
& Replacement
Removal and replacement of the following items. See
Section 5 of the GTN 6XX/7XX PART 27 AML STC SYSTEM
MAINTENANCE MANUAL for instructions.
• GTN 6XX/7XX or GMA 35 units
• NAV antenna cable splitter
• NAV antenna cable diplexer
• Fan
On Condition
Display Backlight
The display backlight LEDs are rated by the manufacturer as
having a usable life of at least 36,000 hours. This life may be
more or less than the rated time depending on the operating
conditions of the GTN. Over time, the backlight lamp may
dim and the display may not perform as well in direct sunlight
conditions. The user must determine by observation when
the display brightness is not suitable for its intended use.
Contact the Garmin factory repair station when the backlight
lamp requires service.
On Condition
Page 4 of 20
Instructions for Continued Airworthiness GTN 6XX/7XX - Bell 206L Series
190-01007-K1 Rev. 2
Item
Description/Procedure
Interval
Battery
Replacement
The GTN has an internal keep-alive battery that will last
about 10 years. The battery is used for GPS system
information. Regular planned replacement is not necessary.
The GTN will display a low battery’ message when
replacement is required. Once the low battery message is
displayed, the battery should be replaced within 1 to 2
months. If the battery is not replaced and becomes totally
discharged, the GTN unit will remain fully operational, but the
GPS signal acquisition time may be increased. There is no
loss of function or accuracy of the GTN unit with a dead
battery. The battery must be replaced by the Garmin factory
repair station or factory authorized repair station.
Perform an electrical bonding check.
On Condition
Test – Bonding
Check, GTN/GMA
Perform an electrical bonding check as follows:
1. Remove the GTN and GMA 35 (if installed) from the
mounting rack(s)
2. Remove the backplate assembly from the rack(s), such
that the harnesses are disconnected.
NOTE
For GTN 7XX only, if the GMA 35 is installed, it must be
removed from its rack and the GMA 35 backplate assembly
must be removed prior to performing Step 3. When a GMA
35 bonding check is planned, perform the GMA 35 bonding
check prior to reinstalling the GTN backplate assembly to the
rack.
To be
performed in
alignment with
Bell 206L
maintenance
schedule. Every
10 years or
every 20th 100
hour inspection,
whichever
comes first.
3. Measure the resistance between each mounting rack and
nearby exposed portion of metallic structure and verify that
the resistance is less than or equal to 10 milliohms.
In the event of bonding test failure, remove the rack and
verify that the countersunk areas around the holes, in the
rack that are used to attach the rack, are free of corrosion or
any other debris. Clean the countersunk areas using an
approved solvent per Bell specification BHT-ELEC-SPM
CHP 8. Reattach the rack to the rails in the panel or
pedestal. Re-verify the resistance between the mounting rack
and nearby exposed portion of aircraft metallic structure and
ensure that the resistance is less than or equal to 2.5
milliohms.
4. Reinstall all backplate assemblies and reinstall the GTN in
the mounting rack.
Page 5 of 20
Instructions for Continued Airworthiness GTN 6XX/7XX - Bell 206L Series
190-01007-K1 Rev. 2
Item
Description/Procedure
Interval
Test – Bonding
Check, HTAWS
Annunciators (if
installed)
Perform an electrical bonding check.
To be
performed in
alignment with
Bell 206L
maintenance
schedule. Every
10 years or
every 20th 100
hour inspection,
whichever
comes first.
Perform an electrical bonding check as follows:
1. Measure the resistance between the metallic body of each
Vivisun annunciator and the instrument panel and verify that
the resistance is less than or equal to 20 milliohms.
In the event of bonding test failure,
1) Inspect the grounding strap which is installed between the
annunciator panel and the instrument panel. Ensure that the
fastener hardware is secure and that the strap is not
damaged. If damaged, replace the bonding strap in
accordance with Garmin Document 190-01007-H1, Sheets 9
and 10.
2) If the problem persists, remove the bonding strap and
clean the mating surfaces of the bonding strap and
annunciator panel/instrument panel per Bell specification
BHT-ELEC-SPM CHP 8.
3) Reinstall the bonding strap and verify that the resistance
between the annunciators and the instrument panel after
prepping the bond surface is less than 10 milliohms.
Page 6 of 20
Instructions for Continued Airworthiness GTN 6XX/7XX - Bell 206L Series
190-01007-K1 Rev. 2
Item
Description/Procedure
Interval
Visual Inspection
The GTN unit, GMA 35 (if installed), HTAWS annunciators (if
installed), switches, and wiring harnesses should be
inspected to ensure continued integrity of the installation in
alignment with Chapter 5, Section 8 (100-Hour and Annual
Inspections) of applicable Bell 206L Model Maintenance
Manual.
To be
performed in
alignment with
Bell 206L
maintenance
schedule.
Every 100 flight
hours or every
12 months,
whichever
comes first.
Conduct a visual check of the GTN unit, switches, GMA 35 (if
installed), HTAWS annunciation indicators (if installed) and
their wiring harnesses to ensure continued installation
integrity.
1. Inspect the GTN unit(s) and GMA 35 for security of
attachment, including visual inspection of mounting racks
and other supporting structure attaching the racks to
rotorcraft instrument panel or avionics console. Verify the
countersunk fastener heads are in full contact with unit
mounting rack holes. Re-torque 12 to 15 in-lbs if required.
2. Inspect for signs of corrosion.
3. Inspect all switches, knobs, and buttons for damage.
4. Inspect placards and switch labels. Ensure that they are
legible and properly adhered. Replace any damaged
labels as necessary.
5. Inspect condition of wiring, shield terminations, routing,
and attachment/clamping.
6. Check the fan intake slots on the sides and bottom of the
GTN unit’s bezel for dust, dirt, or obstructions. Clean as
needed.
Page 7 of 20
Instructions for Continued Airworthiness GTN 6XX/7XX - Bell 206L Series
190-01007-K1 Rev. 2
Table 2. Maintenance Intervals for Antennas Replaced Under this STC
Test – Bonding
Check, GPS
Antennas (Only if
antenna is installed
by this STC)
An electrical bonding test must be performed on antennas
installed by this STC.
1.) Gain access to the antenna installation.
2.) Disconnect coaxial cable(s) from the antenna
connector(s)
3.) Measure the resistance between the antenna connector
and a nearby exposed portion of conductive aircraft
structure (example: exposed rivet)
4.) Verify the resistance is equal to or less than 10
milliohms per Bell specification BHT-ELEC-SPM.
5.) Reconnect the coaxial cable(s) to the antenna
connector(s) and ensure it is secured.
To be
performed in
alignment with
Bell 206L
maintenance
schedule.
Every 10 years
or every 20th
100 hour
inspection,
whichever
comes first.
In the event of bonding test failure, remove antenna, and
clean and prepare the mating surfaces and hardware as
follows:
For antennas that are secured with nuts and bolts, clean the
fastener hole in the antenna and the underside of the
fastener head itself. Prep the area underneath the washer
on the inner mould line of the skin in accordance with Bell
Specification BHT-ELEC-SPM CHP 8. If nutplates are used
in lieu of a nut, the technician is only required to clean the
underneath of the fastener head and the fastener hole.
For antennas that use stud mounts, prep the area
underneath the washer on the inner mould line of the skin in
accordance with Bell Specification BHT-ELEC-SPM CHP 8.
Re-install using unit replacement procedures in the GTN
6XX/7XX PART 27 AML STC SYSTEM MAINTENANCE
MANUAL Section 5. Any reworked antenna installation shall
have a resistance of less than or equal to 2.5 milliohms.
Page 8 of 20
Instructions for Continued Airworthiness GTN 6XX/7XX - Bell 206L Series
190-01007-K1 Rev. 2
Visual Inspection
(Only if antenna is
installed by this
STC)
Visual inspection on the antenna
1. Clean the antenna with water and mild soap.
2. Verify there are no cracks on the antenna and
around attachment fasteners.
3. Verify that all sealing fillets around the antenna are
in good condition.
If the antenna is broken, cracked, or dented it must be
replaced.
To be
performed in
alignment with
Bell 206L
maintenance
schedule.
Every 100 flight
hours or every
12 months,
whichever
comes first.
In the event attachment is not secure, re-attach antenna and
complete the Electrical Bonding Test.
In the event the antenna seal shows signs of damage,
complete the Electrical Bonding Test and re-seal the
antenna.
Perform visual
inspection in
event of
suspected
lightning strike.
Visual inspection of the rotorcraft exterior skin around
installed antenna 1. Clean the exterior of the aircraft skin within a 10 inch
radius of the antenna with water and mild soap.
2. Inspect aircraft skin around the antenna footprint to
verify there are no cracks and aircraft skin is not
deformed.
3. Verify that antenna fasteners are not loose.
If the aircraft skin is cracked, or deformed, the internal
structure must also be inspected for degradation in the local
area. Refer to approved method defined in the Structural
Repair Manual For Bell Model 206 Series Helicopters, BHT206-SRM- 1, Section 3 for fairing repairs.
2.6 Troubleshooting Information
If error indications are displayed on the GTN 6XX or 7XX, consult Section 4, Troubleshooting of the GTN
6XX/7XX PART 27 AML STC SYSTEM MAINTENANCE MANUAL. Refer to the GTN System
Configuration and Checkout Log retained in the aircraft permanent records for a list of the interfaced
equipment and system configuration data.
2.7 Removal and Replacement Information
When replacing a GTN unit or GTN configuration module, the configuration information for the
replacement unit must be set based on approved installation data to ensure proper configuration for this
STC. In particular, per FAA direction, the setting for Airspace Labels must be configured as “Disable”.
For removal and replacement instructions, refer to Section 5, Equipment Removal and Replacement of
the GTN 6XX/7XX PART 27 AML STC SYSTEM MAINTENANCE MANUAL.
2.7.1
Equipment Location and Access
Figure 1 depicts the typical location for GTN LRUs, optional GMA 35, and optional HTAWS annunciators.
Page 9 of 20
Instructions for Continued Airworthiness GTN 6XX/7XX - Bell 206L Series
190-01007-K1 Rev. 2
Figure 1. GTN STC Equipment Fuselage Station Location
Figure 2 depicts a typical installation as performed in the Bell 206L Series and reference notations to the
bill of materials. Table 3 provides the bill of materials in reference to Figure 2.
Page 10 of 20
Instructions for Continued Airworthiness GTN 6XX/7XX - Bell 206L Series
190-01007-K1 Rev. 2
Figure 2 GTN 6XX/7XX Installation in the Bell 206L Series Rotorcraft
Page 11 of 20
Instructions for Continued Airworthiness GTN 6XX/7XX - Bell 206L Series
190-01007-K1 Rev. 2
Table 3. Bill of Materials
29
28
18-440
18-200
PLUG, KEYED, QUICK CONNECT
PLUG, QUICK CONNECT
1
1
1
1
1
25
LED-50-17-11-E14G0
CAP, INDICATOR, HTAWS, STATUS
1
1
1
1
1
24
LED-DM-17-50-BBAKH
BODY, DEFINED LOGIC, MFB (O;DL2/NN/UU;0)
LED-41-11-KB-E11RF
SWITCH, RP MODE,NVIS
LED-41-11-BB-E11ND
SWITCH, RP MODE
LED-40-17-KB-E12XT
INDICATOR, HTAWS, CAUTION AND WARNING,NVIS
LED-40-17-BB-E11R9
INDICATOR, HTAWS, CAUTION AND WARNING
1
1
1
1
1
1
1
1
1
1
23
22
-1
-1
-
-
-
21
011-02302-00
CONNECTOR KIT, GMA 35 AUDIO PANEL
-1
-1
-
-
-
20
011-02300-00
BACKPLATE SUB-ASSEMBLY, GMA 35 AUDIO PANEL
-1
-1
-
-
-
19
011-02645-00
INSTALL RACK KIT, GMA 35 AUDIO PANEL
-1
-1
-
-
-
18
011-02299-00
GMA 35 AUDIO PANEL, REMOTE
1
-
-
-
-
17
011-02326-02
CONNECTOR KIT, GTN 750 NAVIGATOR
-
1
-
-
-
16
011-02326-00
CONNECTOR KIT, GTN 725 NAVIGATOR
-
-
1
-
-
15
011-02325-02
CONNECTOR KIT, GTN 650 NAVIGATOR
-
-
-
1
-
14
011-02325-01
CONNECTOR KIT, GTN 635 NAVIGATOR
-
-
-
-
1
13
011-02325-00
CONNECTOR KIT, GTN 625 NAVIGATOR
-
12
011-02246-02
BACKPLATE SUB-ASSEMBLY, GTN 750 NAVIGATOR
1
-
1
-
-
-
11
011-02246-00
BACKPLATE SUB-ASSEMBLY, GTN 725 NAVIGATOR
-
-
1
-
-
10
011-02245-02
BACKPLATE SUB-ASSEMBLY, GTN 650 NAVIGATOR
-
-
-
1
-
9
011-02245-01
BACKPLATE SUB-ASSEMBLY, GTN 635 NAVIGATOR
-
-
-
-
1
8
011-02245-00
BACKPLATE SUB-ASSEMBLY, GTN 625 NAVIGATOR
1
1
-
-
-
7
115-01294-A0
MOUNTING RACK, GTN 7XX SERIES NAVIAGATOR, HELICOPTER
-
-
1
1
1
6
115-01293-A0
MOUNTING RACK, GTN 6XX SERIES NAVIAGATOR, HELICOPTER
011-02282-A0
GTN 750 TOUCH SCREEN NAVIGATOR, NVIS-B COMPATIBLE
011-02282-50
GTN 750 TOUCH SCREEN NAVIGATOR, GRAY BEZEL
011-02282-00
GTN 750 TOUCH SCREEN NAVIGATOR
011-02281-00
GTN 725 TOUCH SCREEN NAVIGATOR
011-02256-A0
GTN 650 TOUCH SCREEN NAVIGATOR, NVIS-B COMPATIBLE
011-02256-50
GTN 650 TOUCH SCREEN NAVIGATOR, GRAY BEZEL
011-02256-00
GTN 650 TOUCH SCREEN NAVIGATOR
1
-
-
-
-
1
-
-
1
-
-
-
-
-
-
5
4
3
-
-
-
1
-
2
011-02255-00
GTN 635 TOUCH SCREEN NAVIGATOR
-
-
-
-
1
1
011-02254-00
GTN 625 TOUCH SCREEN NAVIGATOR
750
725
650
635
625
ITEM NO.
QTY. PER GTN MODEL
PART NUMBER
OR
OR
DESCRIPTION
TABLE 2. BILL OF MATERIAL
GTN 6XX/7XX NAVIGATOR INSTALLATION
Both GTN and GMA 35 circuit breakers are located on the Bell 206L Series overhead circuit breaker
console. Equipment circuit breaker placards are labeled as follows:
GTN INSTALLATION
LRU
GMA 35
POWER INPUT
Rotorcraft Power on Connector P3502
Rotorcraft Power on Connector P1001
GTN 750
GTN 725
Page 12 of 20
SINGLE
Rotorcraft Power on Connector P1004
DUAL1
Audio
GPS/NAV
Rotorcraft Power on Connector P1003
COM
Rotorcraft Power on Connector P1001
GPS
GPS/NAV 1
GPS/NAV 2
COM 1
COM 2
GPS 1
GPS 2
Instructions for Continued Airworthiness GTN 6XX/7XX - Bell 206L Series
190-01007-K1 Rev. 2
GTN INSTALLATION
LRU
POWER INPUT
Rotorcraft Power on Connector P1001
GTN 650
Rotorcraft Power on Connector P1004
SINGLE
GPS/NAV
Rotorcraft Power on Connector P1003
COM
Rotorcraft Power on Connector P1001
GPS
Rotorcraft Power on Connector P1003
COM
Rotorcraft Power on Connector P1001
GPS
GTN 635
GTN 625
DUAL1
GPS/NAV 1
GPS/NAV 2
COM 1
COM 2
GPS 1
GPS 2
COM 1
COM 2
GPS 1
GPS 2
1. Dual installation labeling applies to GTN LRUs only
Figure 3 depicts the overhead panel location in the Bell 206L Series.
Page 13 of 20
Instructions for Continued Airworthiness GTN 6XX/7XX - Bell 206L Series
190-01007-K1 Rev. 2
Figure 3. Overhead Circuit Breaker Panel in Bell 206L Series
The GTN/GMA 35 wiring harness power and switch connections are routed as shown in Figure 4. Since
the GTNs may be interfaced with preexisting GPS antennas, coaxial wire routing may differ slightly from
the depicted figure. Refer to the aircraft wire routing worksheets and equipment location forms that were
filled out during initial GTN/GMA 35 installation for additional details.
Page 14 of 20
Instructions for Continued Airworthiness GTN 6XX/7XX - Bell 206L Series
190-01007-K1 Rev. 2
Figure 4. GTN/GMA 35 wire routing in the Bell 206L Series
GTN/GMA 35 installation racks, backplates, and wiring harnesses may be accessed by either removing
the GTN LRUs as specified in GTN 6XX/7XX PART 27 AML STC SYSTEM MAINTENANCE MANUAL
Section 5, Equipment Removal and Replacement or by removing the side panel of the Bell 206L Series
console. Figure 4 depicts the installation with the side panel removed.
2.7.2
Weight and Balance
The location of equipment as well as the weight and moment arm for each item is depicted in Figure 5
and Table 4.
Page 15 of 20
Instructions for Continued Airworthiness GTN 6XX/7XX - Bell 206L Series
190-01007-K1 Rev. 2
Figure 5 Equipment Location
Table 4. GTN Equipment Weight and Moment Arm
TABLE 1. WEIGHT AND BALANCE - GTN NAVIGATOR INSTALLATION, TYPICAL
ITEM DESCRIPTION
1
2
3
4
5
6
7
8
9
PART NUMBER
GTN 625 NAVIGATOR [3]
GTN 635 NAVIGATOR [3]
GTN 650 NAVIGATOR [3]
GTN 725 NAVIGATOR [3]
GTN 750 NAVIGATOR [3]
GMA 35 REMOTE MOUNT AUDIO PANEL [3]
CAUTION AND WARNING INDICATOR, HTAWS, VIVISUN
STATUS ANNUNCIATOR, HTAWS, VIVISUN
SWITCH, RP MODE, HTAWS, VIVISUN
011-02254-00
011-02255-00
011-02256-00
011-02281-00
011-02282-00
011-02299-00
LED-40-17-KB-E12XT
LED-DM-17-XX-BBAKH
LED-41-11-BB-E11ND
LATERAL
WEIGHT LONGITUDINAL
ARM [IN] MOMENT ARM [IN] MOMENT
[LB]
6
42.48
254.88
0
0
6.8
42.48
288.86
0
0
7.6
42.48
322.85
0
0
8.6
40.9
351.74
0
0
10.2
40.9
417.18
0
0
2.2
39.21
86.26
0
0
0.06
42.6
2.56
9
0.54
0.06
42.6
2.56
9.74
0.58
0.06
48.75
2.93
2.59
0.16
Note: Weight specified includes the unit, install rack, and backplate assembly with connectors.
Page 16 of 20
Instructions for Continued Airworthiness GTN 6XX/7XX - Bell 206L Series
190-01007-K1 Rev. 2
2.8 Diagrams
Aircraft specific LRU locations and wire routing diagram are contained in Appendix A of this document.
Completed forms are to be retained with the aircraft permanent records.
Point-to-point wiring diagrams for the GTN, GMA 35, and interfaced equipment included with the aircraft
permanent records.
GTN and GMA 35 locations are described in Section 2.7 of this document.
2.9 Special Inspection Requirements
If an antenna is replaced under this STC, an antenna visual inspection must be performed if there is a
suspected lighting strike on the aircraft. In the event of a suspected or actual lightning strike to the
aircraft, the GPS antenna(s) and its associated installation shall be inspected.
If the antenna was struck by lightning then the antenna and the surrounding installation shall be inspected
to ensure that there is no structural damage around the areas where lightning may have struck. See
Table 2 for inspection criteria.
Execute the system checkout procedure for the GPS/WAAS and/or SiriusXM™ system using the
antenna, to ensure the system(s) are operating correctly.
No action is required for hard landing inspections.
2.10
Application of Protective Treatments
None. N/A.
2.11
Data Relative to Structural Fasteners
Refer to Garmin P/N 190-01007-B1, GTN 6XX/7XX PART 27 AML STC SYSTEM MAINTENANCE
MANUAL Section 5 for fastener information.
2.12
Special Tools
A milliohm meter with an accuracy of +/- 0.1 milliohms ohms (or better) is required to measure the
electrical bonding between the GTN/GMA system components and aircraft ground.
2.13
Additional Instructions
None. N/A
2.14
Overhaul Period
The system does not require overhaul at a specific time period. Power on self-test and continuous BIT will
monitor the health of the GTN system. If any LRU indicates an internal failure, the unit may be removed
and replaced (Refer to Section 5 of the GTN 6XX/7XX PART 27 AML STC SYSTEM MAINTENANCE
MANUAL for Removal and Reinstallation instructions). See GTN 6XX/7XX PART 27 AML STC SYSTEM
MAINTENANCE MANUAL, Section 4 for Troubleshooting information.
2.15
ICA Revision and Distribution
To revise this ICA, Garmin will follow the Garmin ODA Procedures Manual SOP-0055/ACP-0016 for
Instructions for Continued Airworthiness. The latest revision of this ICA document is available on the
Garmin website (www.flyGarmin.com). To Access Aviation Manuals, select the ‘Support’ tab and then
select ‘Manuals’. You may also contact Garmin General Aviation Product Support at 866-739-5687 (US
toll free) 913-397-8200 or avionics@garmin.com. A Garmin Service Bulletin describing ICA revision will
be sent to Garmin dealers if a revision is determined to be significant.
Page 17 of 20
Instructions for Continued Airworthiness GTN 6XX/7XX - Bell 206L Series
190-01007-K1 Rev. 2
2.16
Assistance
Flight Standards Inspectors or the certificate holder’s PMI have the required resources to respond to
questions regarding this ICA. In addition, the customer may contact Garmin with questions regarding this
equipment and its installation. Garmin Customer Support may be contacted during normal business hours
via telephone 913-397-8200 or from the Garmin web site at www.flyGarmin.com.
2.17
Implementation and Record Keeping
Modification of an aircraft by this Supplemental Type Certificate obligates the aircraft operator to include
the maintenance information provided by this document in the operator’s aircraft maintenance manual
and/or the operator’s rotorcraft scheduled maintenance program.
Page 18 of 20
Instructions for Continued Airworthiness GTN 6XX/7XX - Bell 206L Series
190-01007-K1 Rev. 2
APPENDIX A
EQUIPMENT LOCATIONS AND WIRE ROUTING
The following diagram must be completed to depict the location of all LRUs and antenna(s) along with the
wire routing for the GTN 6XX/7XX and GMA 35 throughout the aircraft structure for the Bell 206L Series
rotorcraft. All harnesses fabricated as part of this STC should be included in this diagram.
Page 20 of 20
Instructions for Continued Airworthiness GTN 6XX/7XX - Bell 206L Series
190-01007-K1 Rev. 2
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising