Garmin | G1000: Diamond DA42NG | Garmin G1000: Diamond DA42NG G1000 Cockpit Reference Guide for Diamond DA42NG

Garmin G1000: Diamond DA42NG G1000 Cockpit Reference Guide for Diamond DA42NG
G1000
®
Integrated Flight Deck
Cockpit Reference Guide for the Diamond DA42NG
FLIGHT INSTRUMENTS
ENGINE INDICATION SYSTEM
NAV/COM/TRANSPONDER/AUDIO PANEL
AUTOMATIC FLIGHT CONTROL SYSTEM
GPS NAVIGATION
FLIGHT PLANNING
PROCEDURES
HAZARD AVOIDANCE
ADDITIONAL FEATURES
ABNORMAL OPERATION
ANNUNCIATIONS & ALERTS
APPENDIX
INDEX
Copyright © 2009, 2011-2012, 2014-2016 Garmin Ltd. or its subsidiaries. All rights reserved.
This manual reflects the operation of System Software version 0752.13 or later for the Diamond
DA42NG. Some differences in operation may be observed when comparing the information in
this manual to earlier or later software versions.
Garmin International, Inc., 1200 East 151st Street, Olathe, Kansas 66062, U.S.A.
Tel: 913/397.8200Fax: 913/397.8282
Aircraft On Ground (AOG) Hotline: 913.397.0836
Aviation Dealer Technical Support: 888.606.5482
Garmin AT, Inc., 2345 Turner Road SE, Salem, OR 97302, U.S.A.
Tel: 503/391.3411Fax 503/364.2138
Garmin (Europe) Ltd.
Liberty House, Hounsdown Business Park, Southampton, Hampshire SO40 9LR U.K.
Tel:44 (0) 23 8052 4000
Fax:44 (0) 23 8052 4004
Aviation Support:44 (0) 87 0850 1243
Garmin Corporation, No. 68, Jangshu 2nd Road, Xizhi District, New Taipei City, Taiwan
Tel: 34-93-357-2608
Fax: 34-93-429-4484
Web Site Address: www.garmin.com
Except as expressly provided herein, no part of this manual may be reproduced, copied,
transmitted, disseminated, downloaded or stored in any storage medium, for any purpose
without the express written permission of Garmin. Garmin hereby grants permission to
download a single copy of this manual and of any revision to this manual onto a hard drive or
other electronic storage medium to be viewed for personal use, provided that such electronic
or printed copy of this manual or revision must contain the complete text of this copyright
notice and provided further that any unauthorized commercial distribution of this manual or any
revision hereto is strictly prohibited.
Garmin® and G1000® are registered trademarks of Garmin Ltd. or its subsidiaries. FliteCharts®,
SafeTaxi®, and WATCH® are registered trademarks of Garmin Ltd. or its subsidiaries. ESP™ and
Connext™ are trademarks of Garmin Ltd. or its subsidiaries. These trademarks may not be used
without the express permission of Garmin.
NavData® is a registered trademark of Jeppesen, Inc.; Stormscope® is a registered trademark
of L-3 Communications.
190-00963-04 Rev. A
Garmin G1000 Cockpit Reference Guide for the Diamond DA42NG
SiriusXM Weather and SiriusXM Satellite Radio are provided by SiriusXM Satellite Radio, Inc.
AC-U-KWIK® is a registered trademark of Penton Business Media Inc.
AOPA Membership Publications, Inc. and its related organizations (hereinafter collectively
“AOPA”) expressly disclaim all warranties, with respect to the AOPA information included in this
data, express or implied, including, but not limited to, the implied warranties of merchantability
and fitness for a particular purpose. The information is provided “as is” and AOPA does not
warrant or make any representations regarding its accuracy, reliability, or otherwise. Under
no circumstances including negligence, shall AOPA be liable for any incidental, special or
consequential damages that result from the use or inability to use the software or related
documentation, even if AOPA or an AOPA authorized representative has been advised of the
possibility of such damages. User agrees not to sue AOPA and, to the maximum extent allowed
by law, to release and hold harmless AOPA from any causes of action, claims or losses related
to any actual or alleged inaccuracies in the information. Some jurisdictions do not allow the
limitation or exclusion of implied warranties or liability for incidental or consequential damages
so the above limitations or exclusions may not apply to you.
AC-U-KWIK® and its related organizations (hereafter collectively “AC-U-KWIK Organizations”)
expressly disclaim all warranties with respect to the AC-U-KWIK information included in this data,
express or implied, including, but not limited to, the implied warranties of merchantability and
fitness for a particular purpose. The information is provided “as is” and AC-U-KWIK Organizations
do not warrant or make any representations regarding its accuracy, reliability, or otherwise. Licensee
agrees not to sue AC-U-KWIK Organizations and, to the maximum extent allowed by law, to release
and hold harmless AC-U-KWIK Organizations from any cause of action, claims or losses related to
any actual or alleged inaccuracies in the information arising out of Garmin’s use of the information
in the datasets. Some jurisdictions do not allow the limitation or exclusion of implied warranties
or liability for incidental or consequential damages so the above limitations or exclusions may not
apply to licensee.
Printed in the U.S.A.
Garmin G1000 Cockpit Reference Guide for the Diamond DA42NG
190-00963-04 Rev. A
Warnings, Cautions & Notes
WARNING: Do not use terrain avoidance displays as the sole source of information for maintaining separation from terrain and obstacles. Garmin obtains
terrain and obstacle data from third party sources and cannot independently
verify the accuracy of the information.
WARNING: Always refer to current aeronautical charts and NOTAMs for
verification of displayed aeronautical information. Displayed aeronautical
data may not incorporate the latest NOTAM information.
WARNING: Do not use geometric altitude for compliance with air traffic
control altitude requirements. The primary barometric altimeter must be used
for compliance with all air traffic control altitude regulations, requirements,
instructions, and clearances.
WARNING: Do not use basemap information (land and water data) as the
sole means of navigation. Basemap data is intended only to supplement other
approved navigation data sources and should be considered only an aid to
enhance situational awareness.
WARNING: Do not rely solely upon the display of traffic information to
accurately depict all of the traffic within range of the aircraft. Due to lack
of equipment, poor signal reception, and/or inaccurate information from
aircraft or ground stations, traffic may be present that is not represented on
the display.
WARNING: Do not use data link weather information for maneuvering in,
near, or around areas of hazardous weather. Information contained within
data link weather products may not accurately depict current weather conditions.
WARNING: Do not use the indicated data link weather product age to determine the age of the weather information shown by the data link weather
product. Due to time delays inherent in gathering and processing weather
data for data link transmission, the weather information shown by the data
link weather product may be significantly older than the indicated weather
product age.
190-00963-04 Rev. A
Garmin G1000 Cockpit Reference Guide for the Diamond DA42NG
Warnings, Cautions & Notes
WARNING: The displayed minimum safe altitude (MSAs) are only advisory
in nature and should not be relied upon as the sole source of obstacle and
terrain avoidance information. Always refer to current aeronautical charts for
appropriate minimum clearance altitudes.
WARNING: Always obtain qualified instruction prior to operational use of
this equipment.
WARNING: Do not use a QFE altimeter setting with this system. System
functions will not operate properly with a QFE altimeter setting. Use only
a QNH altimeter setting for height above mean sea level, or the standard
pressure setting, as applicable.
WARNING: Do not use GPS to navigate to any active waypoint identified as
a ‘NON WGS84 WPT’ by a system message. ‘NON WGS84 WPT’ waypoints
are derived from an unknown map reference datum that may be incompatible
with the map reference datum used by GPS (known as WGS84) and may be
positioned in error as displayed.
WARNING: When using the autopilot to fly an approach with vertical guidance, the autopilot will not level the aircraft at the MDA/DH even if the MDA/
DH is set in the altitude preselect.
WARNING: Do not rely solely upon the display of traffic information for collision avoidance maneuvering. The traffic display does not provide collision
avoidance resolution advisories and does not under any circumstances or
conditions relieve the pilot’s responsibility to see and avoid other aircraft.
WARNING: Because of variation in the earth’s magnetic field, do not rely
on the accuracy of attitude and heading indications (GRS 77 installations
only) in the following geographic areas: North of 72° North latitude at all
longitudes; South of 70° South latitude at all longitudes; North of 65° North
latitude between longitude 75° W and 120° W. (Northern Canada); North of
70° North latitude between longitude 70° W and 128° W. (Northern Canada);
North of 70° North latitude between longitude 85° E and 114° E. (Northern
Russia); South of 55° South latitude between longitude 120° E and 165° E.
(Region south of Australia and New Zealand).
Garmin G1000 Cockpit Reference Guide for the Diamond DA42NG
190-00963-04 Rev. A
Warnings, Cautions & Notes
WARNING: Do not rely on information from a lightning detection system
display as the sole basis for hazardous weather avoidance. Range limitations
and interference may cause the system to display inaccurate or incomplete
information. Refer to documentation from the lightning detection system
manufacturer for detailed information about the system.
WARNING: Use appropriate primary systems for navigation, and for terrain,
obstacle, and traffic avoidance. Garmin SVT is intended as an aid to situational awareness only and may not provide either the accuracy or reliability
upon which to solely base decisions and/or plan maneuvers to avoid terrain,
obstacles, or traffic.
WARNING: Intruder aircraft at or below 500 ft. AGL may not appear on the
Garmin SVT display or may appear as a partial symbol.
WARNING: Do not use the Garmin SVT runway depiction as the sole means
for determining the proximity of the aircraft to the runway or for maintaining
the proper approach path angle during landing.
WARNING: Do not operate the weather radar in a transmitting mode when
personnel or objects are within the MPEL boundary.
WARNING: Always position the weather radar gain setting to Calibrated for
viewing the actual intensity of precipitation. Changing the gain in weather
mode causes precipitation intensity to be displayed as a color not representative of the true intensity.
CAUTION: Do not clean display surfaces with abrasive cloths or cleaners
containing ammonia. They will harm the anti-reflective coating.
CAUTION: Repairs should only be made by an authorized Garmin service
center. Unauthorized repairs or modifications could void both the warranty
and affect the airworthiness of the aircraft.
190-00963-04 Rev. A
Garmin G1000 Cockpit Reference Guide for the Diamond DA42NG
Warnings, Cautions & Notes
NOTE: Do not rely solely upon data link services to provide Temporary Flight
Restriction (TFR) information. Always confirm TFR information through official
sources such as Flight Service Stations or Air Traffic Control.
NOTE: All visual depictions contained within this document, including screen
images of the system panel and displays, are subject to change and may not
reflect the most current system and aviation databases. Depictions of equipment may differ slightly from the actual equipment.
NOTE: The United States government operates the Global Positioning System
and is solely responsible for its accuracy and maintenance. The GPS system
is subject to changes which could affect the accuracy and performance of all
GPS equipment. Portions of the system utilize GPS as a precision electronic
NAVigation AID (NAVAID). Therefore, as with all NAVAIDs, information
presented by the system can be misused or misinterpreted and, therefore,
become unsafe.
NOTE: This device complies with part 15 of the FCC Rules. Operation is
subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
NOTE: Interference from GPS repeaters operating inside nearby hangars can
cause an intermittent loss of attitude and heading displays while the aircraft
is on the ground. Moving the aircraft more than 100 yards away from the
source of the interference should alleviate the condition.
NOTE: Use of polarized eyewear may cause the flight displays to appear dim
or blank.
NOTE: This product, its packaging, and its components contain chemicals
known to the State of California to cause cancer, birth defects, or reproductive
harm. This notice is being provided in accordance with California’s Proposition
65. If you have any questions or would like additional information, please
refer to our web site at www.garmin.com/prop65.
Garmin G1000 Cockpit Reference Guide for the Diamond DA42NG
190-00963-04 Rev. A
Warnings, Cautions & Notes
NOTE: Operating the system in the vicinity of metal buildings, metal structures, or electromagnetic fields can cause sensor differences that may result
in nuisance miscompare annunciations during start up, shut down, or while
taxiing. If one or more of the sensed values are unavailable, the annunciation
indicates no comparison is possible.
NOTE: The system responds to a terminal procedure based on data coded
within that procedure in the Navigation Database. Differences in system
operation may be observed among similar types of procedures due to differences in the Navigation Database coding specific to each procedure.
NOTE: The FAA has asked Garmin to remind pilots who fly with Garmin
database-dependent avionics of the following:
IT is the pilot’s responsibility to remain familiar with all FAA regulatory and
advisory guidance and information related to the use of databases in the
National Airspace System.
GARMIN equipment will only recognize and use databases that are obtained
from Garmin or Jeppesen. Databases obtained from Garmin or Jeppesen are
assured compliance with all data quality requirements (DQRs) by virtue of a
Type 2 Letter of Authorization (LOA) from the FAA. A copy of the Type 2 LOA
is available for each database and can be viewed at http://fly.garmin.com by
selecting ‘Type 2 LOA Status.’
USE of a current Garmin or Jeppesen database in your Garmin equipment
is required for compliance with established FAA regulatory guidance, but
does not constitute authorization to fly any and all terminal procedures that
may be presented by the system. It is the pilot’s responsibility to operate in
accordance with established AFM(S) and regulatory guidance or limitations
as applicable to the pilot, the aircraft, and installed equipment.
190-00963-04 Rev. A
Garmin G1000 Cockpit Reference Guide for the Diamond DA42NG
Warnings, Cautions & Notes
NOTE: The pilot/operator must review and be familiar with Garmin’s database
exclusion list as discussed in SAIB CE-14-04 to determine what data may be
incomplete. The database exclusion list can be viewed at www.flygarmin.
com by selecting ‘Database Exclusions List.’
NOTE: The pilot/operator must have access to Garmin and Jeppesen database alerts and consider their impact on the intended aircraft operation. The
database alerts can be viewed at www.flygarmin.com by selecting ‘Aviation
Database Alerts.’
NOTE: If the pilot/operator wants or needs to adjust the database, contact
Garmin Product Support to coordinate the revised DQRs.
NOTE: Garmin requests the flight crew report any observed discrepancies
related to database information. These discrepancies could come in the form
of an incorrect procedure; incorrectly identified terrain, obstacles and fixes; or
any other displayed item used for navigation or communication in the air or
on the ground. Go to FlyGarmin.com and select ‘Aviation Data Error Report’.
NOTE: Lamp(s) inside this product contain mercury (HG) and must be recycled
or disposed of according to local, state, or federal laws. For more information,
refer to our website at www.garmin.com/aboutGarmin/environment/disposal.
jsp
NOTE: When using Stormscope, there are several atmospheric phenomena in
addition to nearby thunderstorms that can cause isolated discharge points in
the strike display mode. However, clusters of two or more discharge points
in the strike display mode do indicate thunderstorm activity if these points
reappear after the screen has been cleared.
Garmin G1000 Cockpit Reference Guide for the Diamond DA42NG
190-00963-04 Rev. A
Record of Revisions
Part Number
190-00963-00
Rev A
Change Summary
Initial release at GDU 9.05
Rev B
190-00963-01
Rev A
Added Synthetic Vision System
Rev B
190-00963-02
Rev A
Added note to the Auxiliary Video section
Added GDU 11.12
Added Database Synchronization
Added Electronic Checklists
Added AOPA Airport Directory
Added flight plan import/export
Added Auxiliary Video
Changed procedure for creating user waypoints
Added GDU 12.03
Added Electronic Stability & Protection (ESP™)
Added GFDS World Wide Weather
Added FIS-B Weather
Added Airborne Color Weather Radar
Added ADS-B Traffic
Added Iridium Satellite Telephone and SMS
Added Profile View
Added AC-U-KWIK® Airport Directory references
Updated SiriusXM references
Updated database loading procedure
Updated message advisories
Updated softkey maps
Rev B
Replaced missing content on affected pages.
Rev C
Added Underspeed Protection
Updated ESP pitch limits
Changed GFC 700 to Garmin AFCS
190-00963-04 Rev. A
Garmin G1000 Cockpit Reference Guide for the Diamond DA42NG
RR-1
Record of Revisions
Part Number
190-00963-03
190-00963-04
Change Summary
Added Radar Altimeter (optional)
Added User Defined Holding Patterns
Added temperature compensated altitude
Updated System Message Advisories
Updated Warnings, Cautions, and Notes
Changed GFDS to Connext
Changed Synthetic Vision System (SVS) to Synthetic Vision Technology (SVT)
Added other GDU 14.02 parameters
Added support for GDL 69/69A SXM
Added Support for ADS-B Traffic and Weather
Added Bluetooth® connectivity
Updated Warnings, Cautions, and Notes
Added other GDU 15.11 parameters
Added Support for GSR 56 Iridium Transceiver
Added Wi-Fi connectivity
Revision Date of Revision Affected Pages
A
May, 2016
All
RR-2
Description
Production release
Garmin G1000 Cockpit Reference Guide for the Diamond DA42NG
190-00963-04 Rev. A
Table of Contents
Flight Instruments........................................................................................................................ 1
Selecting the Altimeter Barometric Pressure Setting....................................................... 1
Selecting Standard Barometric Pressure (29.92 in Hg)..................................................... 1
Change Altimeter Barometric Pressure Setting Units....................................................... 1
Change Navigation Sources.................................................................................................... 1
Enable/Disable OBS Mode While Navigating with GPS..................................................... 2
Generic Timer.............................................................................................................................. 2
Configure Vspeed Bugs............................................................................................................. 2
Set Barometric/Radar Altimeter Minimum Descent Altitude.......................................... 3
Displaying Wind Data............................................................................................................... 3
Changing HSI Format................................................................................................................ 3
Engine Indication System......................................................................................................... 5
Engine Display............................................................................................................................ 5
System Display........................................................................................................................... 6
Fuel Display................................................................................................................................. 6
Nav/Com/Transponder/Audio Panel.................................................................................... 9
Enter or Change Flight ID........................................................................................................ 9
ADF Tuning (Optional)............................................................................................................... 9
DME Tuning (Optional).............................................................................................................. 9
Enter a Transponder Code..................................................................................................... 10
Selecting a COM Radio........................................................................................................... 10
Selecting a NAV Radio............................................................................................................ 10
NAV/COM Tuning...................................................................................................................... 10
Digital Clearance Recorder and Player............................................................................... 11
Intercom System (ICS) Isolation........................................................................................... 11
Garmin Automatic Flight Control System (Optional)............................................. 13
Flight Director Activation...................................................................................................... 13
Vertical Modes.......................................................................................................................... 14
Lateral Modes........................................................................................................................... 15
Underspeed Protection........................................................................................................... 15
GPS Navigation............................................................................................................................ 17
Direct-to Navigation............................................................................................................... 17
Activate a Stored Flight Plan................................................................................................ 18
Activate a Flight Plan Leg...................................................................................................... 18
Stop Navigating a Flight Plan............................................................................................... 19
Vertical Navigation (VNV)...................................................................................................... 19
190-00963-04 Rev. A
Garmin G1000 Cockpit Reference Guide for the Diamond DA42NG
i
Table of Contents
Flight Planning............................................................................................................................. 21
Trip Planning............................................................................................................................. 21
Create a User Waypoint Defined by Latitude & Longitude............................................ 23
Create a User Waypoint Defined by Radials from Other Waypoints............................ 23
Create a User Waypoint Defined by a Radial & Distance from Another Waypoint... 25
Delete a User Waypoint.......................................................................................................... 26
Create a Flight Plan................................................................................................................. 27
Import a Flight Plan from an SD Card................................................................................. 28
Insert a Waypoint in the Active Flight Plan....................................................................... 29
Enter an Airway in a Flight Plan........................................................................................... 29
User-Defined Holding Patterns............................................................................................. 30
Invert an Active Flight Plan................................................................................................... 32
Remove a Departure, Arrival, Approach, or Airway from a Flight Plan...................... 32
Store a Flight Plan................................................................................................................... 33
Edit a Stored Flight Plan........................................................................................................ 33
Delete a Waypoint from the Flight Plan............................................................................. 33
Invert and Activate a Stored Flight Plan............................................................................ 34
Copy a Flight Plan.................................................................................................................... 34
Delete a Flight Plan................................................................................................................. 34
Graphical Flight Plan Creation.............................................................................................. 35
Export a Flight Plan to an SD Card...................................................................................... 35
Procedures...................................................................................................................................... 37
Load and Activate a Departure Procedure........................................................................ 37
Activate a Departure Leg....................................................................................................... 37
Load an Arrival Procedure..................................................................................................... 37
Activate an Arrival Leg........................................................................................................... 38
Load and/or Activate an Approach Procedure.................................................................. 38
Activate an Approach in the Active Flight Plan................................................................ 40
Activate a Vector to Final Approach Fix............................................................................. 40
Activate a Missed Approach in the Active Flight Plan.................................................... 40
Temperature Compensated Altitude................................................................................... 40
Hazard Avoidance....................................................................................................................... 43
Customizing the Hazard Displays on the Navigation Map............................................. 43
Stormscope® (Optional)......................................................................................................... 43
SiriusXM Weather (Optional)................................................................................................ 45
Garmin Connext Weather (Optional)................................................................................... 47
FIS-B Weather........................................................................................................................... 59
Airborne Color Weather Radar............................................................................................. 66
Traffic Systems......................................................................................................................... 70
GDL 88 ADS-B Traffic (Optional)........................................................................................... 72
Terrain and Obstacle Proximity............................................................................................ 75
Terrain-SVS................................................................................................................................ 76
ii
Garmin G1000 Cockpit Reference Guide for the Diamond DA42NG
190-00963-04 Rev. A
Table of Contents
Additional Features................................................................................................................... 79
Synthetic Vision (Optional).................................................................................................... 79
Terminal Procedure Charts.................................................................................................... 80
Airport Directory..................................................................................................................... 82
SiriusXM Satellite Radio Entertainment (Optional)......................................................... 83
Satellite Telephone & SMS Messaging Service (Optional)............................................. 84
WI-FI Connections.................................................................................................................... 96
Electronic Stability and Protection (ESP™)......................................................................... 98
Auxiliary Video (Optional)................................................................................................... 100
Scheduler................................................................................................................................. 101
Pilot Profiles........................................................................................................................... 103
Electronic Checklists (Optional).......................................................................................... 106
Abnormal Operation............................................................................................................... 109
Reversionary Mode............................................................................................................... 109
Abnormal COM Operation................................................................................................... 109
Hazard Displays with Loss of GPS Position...................................................................... 109
Unusual Attitudes.................................................................................................................. 110
Dead Reckoning..................................................................................................................... 110
Annunciations & Alerts.......................................................................................................... 113
WARNING Alerts..................................................................................................................... 113
CAUTION Alerts....................................................................................................................... 114
Annunciation Advisory......................................................................................................... 115
Message Advisory Alerts...................................................................................................... 115
AFCS Alerts.............................................................................................................................. 116
TAS Alerts and Annunciations............................................................................................. 117
TIS Alerts and Annunciations.............................................................................................. 118
SVS Terrain Alerts.................................................................................................................. 119
SVS Terrain Status Annunciations...................................................................................... 120
ADS-B Alerts and Annunciations........................................................................................ 121
Weather Radar Alerts and Annunciations........................................................................ 123
GDL 69A/GDL 69A SXM Data Link Receiver Messages.................................................. 124
Voice Alerts............................................................................................................................. 125
MFD & PFD Message Advisories......................................................................................... 126
Flight Plan Import/Export Messages................................................................................. 144
Appendix........................................................................................................................................ 147
PFD Softkey Map................................................................................................................... 147
MFD Softkey Map.................................................................................................................. 152
Loading Updated Databases............................................................................................... 155
Index............................................................................................................................................Index-1
190-00963-04 Rev. A
Garmin G1000 Cockpit Reference Guide for the Diamond DA42NG
iii
Table of Contents
Blank Page
iv
Garmin G1000 Cockpit Reference Guide for the Diamond DA42NG
190-00963-04 Rev. A
Flight Instruments
Flight
Instruments
FLIGHT INSTRUMENTS
SELECTING THE ALTIMETER BAROMETRIC PRESSURE SETTING
EIS
Turn the BARO Knob to select the desired setting.
Press the PFD Softkey.
2)
Press the STD BARO Softkey to set standard barometric pressure.
AFCS
1)
Nav/Com/
XPDR/Audio
SELECTING STANDARD BAROMETRIC PRESSURE (29.92 IN HG)
CHANGE ALTIMETER BAROMETRIC PRESSURE SETTING UNITS
2)
Press the ALT UNIT Softkey.
3)
Press the IN Softkey to display the barometric pressure setting in inches of
mercury (in Hg).
Flight
Planning
Press the PFD Softkey to display the second-level softkeys.
GPS Nav
1)
Procedures
Or:
Press the HPA Softkey to display the barometric pressure setting in
hectopascals.
Press the BACK Softkey to return to the top-level softkeys.
Hazard
Avoidance
4)
CHANGE NAVIGATION SOURCES
Press the CDI Softkey again to change from VOR1 or LOC1 to VOR2
or LOC2. This places the light blue tuning box over the NAV2 standby
frequency.
3)
Press the CDI Softkey a third time to return to GPS.
Annun/
Alerts
2)
Abnormal
Operation
Press the CDI Softkey to change from GPS to VOR1 or LOC1. This places
the light blue tuning box over the NAV1 standby frequency in the upper left
corner of the PFD.
Additional
Features
1)
Appendix
Index
190-00963-04 Rev. A
Garmin G1000 Cockpit Reference Guide for the Diamond DA42NG
1
ENABLE/DISABLE OBS MODE WHILE NAVIGATING WITH GPS
1)
Press the OBS Softkey to select OBS Mode.
2)
Turn a CRS Knob to select the desired course to/from the waypoint. Press a
CRS Knob to synchronize the Selected Course with the bearing to the next
waypoint.
3)
Press the OBS Softkey again to disable OBS Mode.
1)
Press the TMR/REF Softkey, then turn the large FMS Knob to select the
time field (hh/mm/ss). Turn the FMS Knobs to set the desired time, then
press the ENT Key. The UP/DOWN field is now highlighted.
2)
Turn the small FMS Knob to display the UP/DOWN window. Turn the FMS
Knob to select ‘UP’ or ‘DOWN’, then press the ENT Key. ‘START?’ is now
highlighted.
3)
Press the ENT Key to START, STOP, or RESET the timer (if the timer is
counting DOWN, it starts counting UP after reaching zero). Press the CLR
Key or the TMR/REF Softkey to remove the window.
Additional
Features
CONFIGURE VSPEED BUGS
1) Press the TMR/REF Softkey.
2) Turn the large FMS Knob to highlight the desired Vspeed.
3) Use the small FMS Knob to change the Vspeed in 1-kt increments (when a
Abnormal
Operation
Hazard
Avoidance
Procedures
Flight
Planning
AFCS
GENERIC TIMER
GPS Nav
Nav/Com/
XPDR/Audio
EIS
Flight
Instruments
Flight Instruments
4)
Press the ENT Key or turn the large FMS Knob to highlight the ON/OFF
field.
5)
Turn the small FMS Knob clockwise to ON or counterclockwise to OFF.
6)
To remove the window, press the CLR Key or the TMR/REF Softkey.
Index
Appendix
Annun/
Alerts
speed has been changed from a default value, an asterisk appears next to
the speed).
2
Garmin G1000 Cockpit Reference Guide for the Diamond DA42NG
190-00963-04 Rev. A
Flight Instruments
Flight
Instruments
SET BAROMETRIC/RADAR ALTIMETER MINIMUM DESCENT ALTITUDE
Press the TMR/REF Softkey.
2)
Turn the large FMS Knob to highlight the Minimums field.
3)
Turn the small FMS Knob to select the desired altitude source: barometric
(BARO), temperature compensated (TEMP COMP), or radar altimeter (RAD
ALT). OFF is selected by default. Press the ENT Key or turn the large FMS
Knob to highlight the next field.
4)
Use the small FMS Knob to enter the desired altitude for minimums.
5)
If using temperature compensated (TEMP COMP). use the small FMS Knob
to enter destination air temperature.
6)
To remove the window, press the CLR Key or the TMR/REF Softkey.
EIS
1)
Nav/Com/
XPDR/Audio
GPS Nav
2)
Press the WIND Softkey to display wind data to the left of the HSI.
3)
Press one of the OPTN softkeys to change how wind data is displayed.
4)
To remove the Wind Data Window, press the OFF Softkey.
Procedures
Press the PFD Softkey.
Flight
Planning
1)
Hazard
Avoidance
CHANGING HSI FORMAT
Press the PFD Softkey.
2)
Press the HSI FRMT Softkey.
3)
Press the 360 HSI Softkey to display the full size HSI.
Additional
Features
1)
AFCS
DISPLAYING WIND DATA
Abnormal
Operation
Or:
Press the ARC HSI Softkey to display the arc style HSI.
Annun/
Alerts
Appendix
Index
190-00963-04 Rev. A
Garmin G1000 Cockpit Reference Guide for the Diamond DA42NG
3
Index
Appendix
Annun/
Alerts
Abnormal
Operation
Additional
Features
Hazard
Avoidance
Procedures
Flight
Planning
GPS Nav
AFCS
Nav/Com/
XPDR/Audio
EIS
Flight
Instruments
Flight Instruments
Blank Page
4
Garmin G1000 Cockpit Reference Guide for the Diamond DA42NG
190-00963-04 Rev. A
Engine Indication System
Flight
Instruments
ENGINE INDICATION SYSTEM
Nav/Com/
XPDR/Audio
ENGINE DISPLAY
EIS
NOTE: Refer to the Airplane Flight Manual (AFM) for applicable RPM
indications.
AFCS
Engine Load
Indicator
GPS Nav
Tachometer
Flight
Planning
Procedures
Fuel Flow
Indicator
Hazard
Avoidance
Oil Temperature
Indicator
Additional
Features
Oil Pressure
Indicator
Coolant Temperature
Indicator
Abnormal
Operation
Fuel Temperature
Indicator
Annun/
Alerts
Fuel Quantity
Indicator
Appendix
Engine Display
Index
190-00963-04 Rev. A
Garmin G1000 Cockpit Reference Guide for the Diamond DA42NG
5
SYSTEM DISPLAY
Pressing the ENGINE Softkey displays the SYSTEM and FUEL softkeys. Press the
SYSTEM Softkey to show the System Display.
EIS
Flight
Instruments
Engine Indication System
AFCS
Nav/Com/
XPDR/Audio
Engine Load
Indicator
GPS Nav
Tachometer
Flight
Planning
Voltmeter
Procedures
Ammeter
Hazard
Avoidance
Gearbox Temperature
Indicator
Additional
Features
Coolant Temperature
Indicator
Abnormal
Operation
Oil Temperature
Indicator
Oil Pressure
Indicator
Annun/
Alerts
Deice Fluid
Indicator
Appendix
FUEL DISPLAY
Index
System Display
Pressing the ENGINE Softkey displays the SYSTEM and FUEL softkeys. Press the
FUEL Softkey to show the Fuel Display.
6
Garmin G1000 Cockpit Reference Guide for the Diamond DA42NG
190-00963-04 Rev. A
Engine Indication System
Nav/Com/
XPDR/Audio
AFCS
GPS Nav
Engine Load
Indicator
EIS
- DEC FUEL – Allows the pilot to decrease the gallons of fuel remaining (GAL
REM) in 1-gallon increments
- INC FUEL – Allows the pilot to increase the gallons of fuel remaining in
1-gallon increments
- RST FUEL – Resets the fuel remaining to 50.0 gallons with standard fuel tanks
or 76.4 gallons with auxiliary fuel tanks. Reset gallons used to zero.
Flight
Instruments
Fuel used (GAL USED), endurance (ENDUR), and fuel range (RANGE NM) are
all calculated based on the last manual adjustment of the fuel remaining (GAL REM).
Measured fuel quantity has no effect on fuel calculations. Fuel calculations are
based on sensed fuel flow and the last manual adjustment of the fuel remaining.
Flight
Planning
Tachometer
Procedures
Hazard
Avoidance
Fuel Quantity
Indicator
Fuel Flow
Indicator
Additional
Features
Fuel Temperature
Indicator
Gallons
Remaining
Abnormal
Operation
Fuel Used
Endurance
Annun/
Alerts
Fuel Range in
Nautical Miles
Appendix
Total Time
In Service
Indicator
Index
Fuel Display
190-00963-04 Rev. A
Garmin G1000 Cockpit Reference Guide for the Diamond DA42NG
7
Index
Appendix
Annun/
Alerts
Abnormal
Operation
Additional
Features
Hazard
Avoidance
Procedures
Flight
Planning
GPS Nav
AFCS
Nav/Com/
XPDR/Audio
EIS
Flight
Instruments
Engine Indication System
Blank Page
8
Garmin G1000 Cockpit Reference Guide for the Diamond DA42NG
190-00963-04 Rev. A
Nav/Com/XPDR/Audio Panel
Flight
Instruments
NAV/COM/TRANSPONDER/AUDIO PANEL
ENTER OR CHANGE FLIGHT ID
2)
Turn the small FMS Knob to enter the first character.
3)
Turn the large FMS Knob to select the next field.
4)
Turn the small FMS Knob to enter the next desired character.
5)
Repeat steps 3 and 4 until the desired Flight ID is entered.
6)
Press the ENT Key to update the Flight ID.
Nav/Com/
XPDR/Audio
Press the TMR/REF Softkey, then turn the large FMS Knob to highlight the
Flight ID field.
AFCS
GPS Nav
ADF TUNING (OPTIONAL)
Turn the large FMS Knob to select the next desired field.
4)
Turn the small FMS Knob to enter the desired number.
5)
Repeat steps 3 and 4 until the desired ADF frequency is entered.
6)
Press the ENT Key to accept the new frequency.
7)
Press the ENT Key again to transfer the frequency to the active field.
8)
Turn the large FMS Knob to select the MODE field.
9)
Turn the small FMS Knob to select ANT, ADF, ADF/BFO, or ANT/BFO.
Abnormal
Operation
3)
Additional
Features
Turn the small FMS Knob to enter the first digit of the desired ADF
frequency.
Hazard
Avoidance
2)
Procedures
Press the ADF/DME Softkey.
Flight
Planning
1)
10) Press the ENT Key to complete the selection.
2)
Turn the large FMS to select the DME source field.
3)
Turn the small FMS Knob to select the desired Nav radio.
4)
Press the ENT Key to complete the selection.
Appendix
Press the ADF/DME or DME Softkey.
Annun/
Alerts
DME TUNING (OPTIONAL)
1)
EIS
1)
Index
190-00963-04 Rev. A
Garmin G1000 Cockpit Reference Guide for the Diamond DA42NG
9
ENTER A TRANSPONDER CODE
1)
Press the XPDR Softkey to display the transponder mode selection softkeys.
2)
Press the CODE Softkey to display the transponder code selection softkeys,
for digit entry.
3)
Press the digit softkeys to enter the code in the code field. When entering
the code, the next key in sequence must be pressed within 10 seconds, or
the entry is cancelled and restored to the previous code. Five seconds after
the fourth digit has been entered, the transponder code becomes active.
SELECTING A COM RADIO
Transmit/Receive
GPS Nav
AFCS
Nav/Com/
XPDR/Audio
EIS
Flight
Instruments
Nav/Com/XPDR/Audio Panel
Flight
Planning
Press the COM1 MIC / COM2 MIC Key (optional COM, if installed) on the
audio panel.
Receive Only
SELECTING A NAV RADIO
1)
To begin navigating using a navigation radio, press the CDI Softkey on the
PFD to select VOR1/LOC1 (NAV1) or VOR2/LOC2 (NAV2).
2)
Press the NAV1, NAV2, DME, or ADF Key on the audio panel to select or
deselect the navigation radio audio source. All radio keys can be selected
individually or together.
NAV/COM TUNING
Index
Appendix
Annun/
Alerts
Abnormal
Operation
Additional
Features
Hazard
Avoidance
Procedures
Press the COM1 / COM2 Key (optional COM, if installed) on the audio
panel.
10
1)
Press the small tuning knob to select the desired radio for tuning. A light
blue box highlights the radio frequency to be tuned.
2)
Turn the respective tuning knobs to enter the desired frequency into the
standby frequency field. The large knob enters MHz and the small knob
enters kHz.
3)
Press the Frequency Transfer Key to place the frequency into the active
frequency field.
Garmin G1000 Cockpit Reference Guide for the Diamond DA42NG
190-00963-04 Rev. A
Nav/Com/XPDR/Audio Panel
Flight
Instruments
DIGITAL CLEARANCE RECORDER AND PLAYER
NOTE: Only the audio for the selected COM MIC Key is recorded.
Selected
radios; pilot;
copilot;
passengers;
music
Selected
radios; pilot;
copilot;
passengers;
music
Copilot;
passengers;
music
Copilot;
passengers;
music
PILOT
ON
OFF
Selected
radios; pilot
Copilot
Selected
radios; pilot;
passengers;
music
Selected
radios; pilot;
copilot
Passengers;
music
COPILOT
OFF
ON
Selected
radios; pilot;
passengers;
music
CREW
ON
ON
Selected
radios; pilot;
copilot
Appendix
OFF
Annun/
Alerts
OFF
Abnormal
Operation
ALL
Selected
radios; pilot;
copilot;
passengers;
music
Additional
Features
Passenger
Hears
Hazard
Avoidance
Copilot
Hears
Procedures
Pilot Hears
Flight
Planning
PILOT KEY
COPLT KEY
ANNUNCIATOR ANNUNCIATOR
GPS Nav
Mode
AFCS
Press the PILOT and/or COPLT Key to select those isolated from hearing the Nav/
Com radios and music.
Nav/Com/
XPDR/Audio
INTERCOM SYSTEM (ICS) ISOLATION
EIS
• Pressing the PLAY Key once plays the latest recorded memory block, then returns
to normal operation.
• Pressing the MKR/MUTE Key while playing a memory block stops play.
• Pressing the PLAY Key during play begins playing the previously recorded
memory block. Each subsequent press of the PLAY Key begins playing the next
previously recorded block.
Index
190-00963-04 Rev. A
Garmin G1000 Cockpit Reference Guide for the Diamond DA42NG
11
Index
Appendix
Annun/
Alerts
Abnormal
Operation
Additional
Features
Hazard
Avoidance
Procedures
Flight
Planning
GPS Nav
AFCS
Nav/Com/
XPDR/Audio
EIS
Flight
Instruments
Nav/Com/XPDR/Audio Panel
Blank Page
12
Garmin G1000 Cockpit Reference Guide for the Diamond DA42NG
190-00963-04 Rev. A
AFCS
Flight
Instruments
GARMIN AUTOMATIC FLIGHT CONTROL SYSTEM
(OPTIONAL)
AFCS
FLIGHT DIRECTOR ACTIVATION
Heading Select
PIT
Pitch Hold (default)
PIT
Appendix
HDG Key
Pitch Hold (default)
Annun/
Alerts
Approach**
PIT
Abnormal
Operation
APR Key
Pitch Hold (default)
**The selected navigation receiver must have a valid VOR or LOC signal or active GPS course before
NAV or APR Key press activates flight director.
Garmin G1000 Cockpit Reference Guide for the Diamond DA42NG
13
Index
*Valid VNV flight plan must be entered before VNV Key press activates flight director.
190-00963-04 Rev. A
Additional
Features
Navigation**
GA Button
ROL
ROL
ROL
TO
GA
ROL
ROL
ROL
GPS
VOR
LOC
BC
GPS
VOR
LOC
HDG
Hazard
Avoidance
NAV Key
FD Key
AP Key
CWS Button
Vertical
Pitch Hold (default)
PIT
Pitch Hold (default)
PIT
Pitch Hold (default)
PIT
Takeoff (on ground)
TO
Go Around (in air)
GA
Altitude Hold
ALT
Vertical Speed
VS
Vertical Path Tracking* VPTH
Procedures
ALT Key
VS Key
VNV Key
Lateral
Roll Hold (default)
Roll Hold (default)
Roll Hold (default)
Takeoff (on ground)
Go Around (in air)
Roll Hold (default)
Roll Hold (default)
Roll Hold (default)
Flight
Planning
Modes Selected
GPS Nav
An initial press of a key listed in the following table (when the flight director is not
active) activates the pilot-side flight director in the listed modes.
Control Pressed
Nav/Com/
XPDR/Audio
NOTE: If the attitude information required for the default flight director modes
becomes invalid or unavailable, the autopilot automatically disengages.
EIS
NOTE: If sensor information (other than attitude) required for a flight director
mode becomes invalid or unavailable, the flight director automatically reverts
to the default mode for that axis.
VERTICAL MODES
Vertical Mode
Pitch Hold
Selected Altitude
Armed
Description
Holds the current aircraft pitch
attitude; may be used to climb/
descend to the Selected Altitude
Captures the Selected Altitude
Holds the current Altitude
Reference
Holds aircraft vertical speed; may
Vertical Speed
be used to climb/descend to the
Selected Altitude
Holds aircraft airspeed while
Flight Level Change aircraft is climbing/descending to
the Selected Altitude
Captures and tracks descent legs
Vertical Path Tracking
of an active vertical profile
VNAV Target Altitude Captures the Vertical Navigation
Capture
(VNV) Target Altitude
Captures and tracks the SBAS
Glidepath ***
glidepath on approach
Captures and tracks the ILS
Glideslope
glideslope on approach
Commands a constant pitch
Go Around
attitude and wings level in the air
Altitude Hold
Control
Annunciation
(default)
PIT
*
ALTS
ALT Key
ALT
VS Key
VS
FLC Key
FLC
nnnnn
ft
nnnn
fpm
nnn kt
VNV Key
VPTH
**
ALTV
GP
APR Key
GS
GA Button
GA
* ALTS armed automatically when PIT, VS, FLC, or GA active, and under VPTH when Selected Altitude
is to be captured instead of VNAV Target Altitude
** ALTV armed automatically under VPTH when VNAV Target Altitude is to be captured instead of
Selected Altitude
***GP is available in installations with GIA 63W IAUs when SBAS is available. Refer to the Airplane
Flight Manual to determine whether SBAS functionality is approved.
Index
Appendix
Annun/
Alerts
Abnormal
Operation
Additional
Features
Hazard
Avoidance
Procedures
Flight
Planning
GPS Nav
AFCS
Nav/Com/
XPDR/Audio
EIS
Flight
Instruments
AFCS
14
Garmin G1000 Cockpit Reference Guide for the Diamond DA42NG
190-00963-04 Rev. A
AFCS
Lateral Mode
Hazard
Avoidance
LOC
Additional
Features
GA
Index
15
Appendix
Garmin G1000 Cockpit Reference Guide for the Diamond DA42NG
Annun/
Alerts
Underspeed Protection is available when the autopilot is on. It is designed to discourage aircraft operation below minimum established airspeeds.
When the aircraft airspeed reaches 90 kts and 95 kts, a flashing yellow ‘MINSPD’
annunciation will appear above the airspeed indicator. When the airspeed trend vector reaches a predetermined airspeed (specific to each flap setting), a single aural “AIRSPEED” will sound, alerting the pilot to the impending underspeed condition.
•
Flaps UP
82 kts
•
Flaps APP
80 kts
•
Flaps LDG
75 kts
Abnormal
Operation
UNDERSPEED PROTECTION
190-00963-04 Rev. A
Procedures
GA
Button
Flight
Planning
Commands a constant pitch
angle and wings level
VAPP
GPS Nav
Go Around
APR
Key
AFCS
Approach, VOR Capture/Track
Approach, LOC (Glideslope
Mode automatically armed)
GPS
Captures and tracks the
selected navigation source
(GPS, VOR, LOC)
Nav/Com/
XPDR/Audio
Approach, GPS
EIS
Description
Control Annunciation
Holds the current aircraft roll
attitude or rolls the wings
Roll Hold
(default)
ROL
level, depending on the
commanded bank angle
Captures and tracks the HDG
Heading Select
HDG
Selected Heading
Key
Navigation, GPS
GPS
Navigation, VOR Enroute
Captures and tracks the
VOR
Capture/Track
selected navigation source
NAV
Navigation, LOC Capture/Track (GPS, VOR, LOC)
LOC
Key
(No Glideslope)
Captures and tracks a
Navigation, Backcourse
localizer signal for backcourse
BC
Capture/Track
approaches
Flight
Instruments
LATERAL MODES
If the aircraft continues to decelerate, Underspeed Protection becomes active.
Vertical flight director modes can be divided into two categories: Those in which it
is important to maintain altitude for as long as possible (altitude-critical modes), and
those in which maintaining altitude is less crucial (non-altitude critical modes).
Altitude-Critical Modes (ALT, GS, GP, TO, GA, FLC)
When the aircraft decelerates to stall warning, the lateral and vertical flight director
modes will change from active to armed, and the autopilot will provide input causing
the aircraft to pitch down and the wings to level.
An aural “AIRSPEED” alert will sound every five seconds and a red “USP ACTIVE”
annunciation will appear to the right of the Vertical Speed Indicator (see Annunciations
& Alerts). The pitch down force will continue until the aircraft reaches a pitch attitude
at which IAS equals the IAS at which stall warning turns off, plus two knots.
When airspeed increases (as a result of adding power/thrust) to above the IAS at
which stall warning turns off, plus two knots, the autopilot will cause the aircraft to
pitch up until recapturing the vertical reference and the vertical and lateral flight
director modes will change from armed to active.
Non-Altitude Critical Modes (PIT, VS, VNAV, IAS)
When the aircraft decelerates to an IAS below the minimum commandable autopilot
airspeed, a red “USP ACTIVE” annunciation will appear to the right of the Vertical
Speed Indicator. The vertical flight director mode will change from active to armed,
and the autopilot will cause the aircraft to pitch down until reaching a pitch attitude at
which IAS equals the minimum commandable autopilot airspeed.
When airspeed increases (as a result of adding power/thrust) to an IAS above the
minimum commandable autopilot airspeed, the autopilot will cause the aircraft to
pitch up until recapturing the vertical reference and the vertical flight director mode
will change from armed to active.
Index
Appendix
Annun/
Alerts
Abnormal
Operation
Additional
Features
Hazard
Avoidance
Procedures
Flight
Planning
GPS Nav
AFCS
Nav/Com/
XPDR/Audio
EIS
Flight
Instruments
AFCS
16
Garmin G1000 Cockpit Reference Guide for the Diamond DA42NG
190-00963-04 Rev. A
GPS Navigation
Flight
Instruments
GPS NAVIGATION
DIRECT-TO NAVIGATION
2)
3)
6)
9)
12)
1)
2)
5)
190-00963-04 Rev. A
Garmin G1000 Cockpit Reference Guide for the Diamond DA42NG
17
Index
6)
Appendix
4)
).
Turn the large FMS Knob to place the cursor in the desired selection field.
Turn the small FMS Knob to begin selecting the desired identifier, location,
etc.
Press the ENT Key.
The cursor is now flashing on ‘ACTIVATE?’. If no altitude constraint or
course is desired, press the ENT Key to activate. To enter an altitude
constraint, proceed to step 6.
Turn the large FMS Knob to place the cursor over the ‘ALT’ altitude field.
Annun/
Alerts
3)
Press the Direct-to Key (
Abnormal
Operation
Direct-to Navigation from the PFD
Additional
Features
11)
Hazard
Avoidance
10)
Procedures
8)
Flight
Planning
7)
GPS Nav
5)
) Key.
Enter the waypoint identifier.
Press the ENT Key to confirm the identifier. The ‘Activate?’ field is
highlighted.
If no altitude constraint or course is desired, press the ENT Key to activate.
To enter an altitude constraint, proceed to step 5.
Turn the large FMS Knob to place the cursor over the ‘VNV’ altitude field.
Enter the desired altitude.
Press the ENT Key. If the waypoint entered is an airport, the option to
select MSL or AGL is now displayed. If the waypoint is not an airport,
proceed to step 9.
Turn the small FMS Knob to select ‘MSL’ or ‘AGL’.
Press the ENT Key. The cursor is now flashing in the VNV offset distance
field.
Enter the desired offset distance before (-) the waypoint.
Press the ENT Key. The ‘Activate?’ field is highlighted.
Press the ENT Key to activate.
AFCS
4)
Press the Direct-to (
Nav/Com/
XPDR/Audio
1)
EIS
Direct-to Navigation from the MFD
EIS
Flight
Instruments
GPS Navigation
7)
Turn the small FMS Knob to enter the desired altitude.
8)
Press the ENT Key. If the waypoint entered is an airport, the option to
select MSL or AGL is now displayed. If the waypoint is not an airport,
proceed to step 10.
9)
Turn the small FMS Knob to select ‘MSL’ or ‘AGL’.
Nav/Com/
XPDR/Audio
10) Press the ENT Key. The cursor is placed in the ‘OFFSET’ field.
11) Turn the small FMS Knob to enter the desired target altitude offset from
the selected Direct-to.
AFCS
12) Press the ENT Key to highlight ‘Activate?’ or turn the large FMS Knob to
highlight the ‘CRS’ field.
14) Press the ENT Key to highlight ‘ACTIVATE?’.
15) Press the ENT again to activate the Direct-to.
ACTIVATE A STORED FLIGHT PLAN
1)
Press the FPL Key on the MFD and turn the small FMS Knob to display the
Flight Plan Catalog Page.
2)
Press the FMS Knob to activate the cursor.
3)
Turn the large FMS Knob to highlight the desired flight plan
4)
Press the ACTIVE Softkey. The confirmation window is now displayed.
5)
With ‘OK’ highlighted, press the ENT Key to activate the flight plan. To cancel
the flight plan activation, turn the large FMS Knob to highlight ‘CANCEL’ and
press the ENT Key.
ACTIVATE A FLIGHT PLAN LEG
Annun/
Alerts
Abnormal
Operation
Additional
Features
Hazard
Avoidance
Procedures
Flight
Planning
GPS Nav
13) Turn the small FMS Knob to enter the desired course to the waypoint.
1)
From the Active Flight Plan Page, press the FMS Knob to activate the cursor
and turn the large FMS Knob to highlight the desired waypoint.
2)
On the MFD, press the ACT LEG Softkey.
Appendix
OR
Index
Press the MENU Key, select the ‘Activate Leg’ option from the page menu
and press the ENT Key. This step must be used when activating a leg from
the PFD.
3)
18
With ‘Activate’ highlighted, press the ENT Key.
Garmin G1000 Cockpit Reference Guide for the Diamond DA42NG
190-00963-04 Rev. A
GPS Navigation
Flight
Instruments
STOP NAVIGATING A FLIGHT PLAN
2)
Press the MENU Key to display the Page Menu Window.
3)
Turn the large FMS Knob to highlight ‘Delete Flight Plan’ and press the ENT
Key. With ‘OK’ highlighted, press the ENT Key to deactivate the flight plan.
This does not delete the stored flight plan, only the active flight plan.
VERTICAL NAVIGATION (VNV)
AFCS
GPS Nav
The navigation database only contains altitudes for procedures that call for “Cross
at” altitudes. If the procedure states “Expect to cross at,” the altitude is not in the
database. In this case the altitude may be entered manually.
Nav/Com/
XPDR/Audio
Press the FPL Key to display the Active Flight Plan Page.
EIS
1)
Flight
Planning
Procedures
Large White
Text
Large Light
Blue Text
Hazard
Avoidance
Small Light
Blue Text
Additional
Features
Small Light
Blue Subdued
Text
Abnormal
Operation
Small White Text
with Altitude
Restriction Bar
Annun/
Alerts
Cross AT or ABOVE 5,000 ft
Appendix
Cross AT 2,300 ft
Cross AT or BELOW 3,000 ft
Index
190-00963-04 Rev. A
Garmin G1000 Cockpit Reference Guide for the Diamond DA42NG
19
Altitudes associated with approach procedures are “auto-designated”. This means
the system automatically uses the altitudes loaded with the approach for giving vertical
flight path guidance outside the FAF. Note these altitudes are displayed as small light
blue text.
Altitudes associated with arrival procedures are “manually-designated”. This means
the system does not use the altitudes loaded with the arrival for giving vertical flight
path guidance until designated to do so by the pilot. Note that these altitudes are
initially displayed as white text. These altitudes may be “designated” by placing the
cursor over the desired altitude and pressing the ENT Key. After designation, the text
changes to light blue.
Altitudes that have been designated for use in vertical navigation may also be
made “non-designated” by placing the cursor over the desired altitude and pressing
the CLR Key. The altitude is now displayed only as a reference. It will not be used
to give vertical flight path guidance. Other displayed altitudes may change due to
re-calculations or rendered invalid as a result of manually changing an altitude to a
non-designated altitude.
White Text
Light Blue Text
Large Text
Altitude calculated by the
system estimating the
altitude of the aircraft as it
passes over the navigation
point. This altitude is
provided as a reference
and is not designated to
be used in determining
vertical flight path
guidance.
Altitude has been entered
by the pilot. Altitude is
designated for use in
giving vertical flight path
guidance. Altitude does
not match the published
altitude in navigation
database or no published
altitude exists.
The system cannot
use this altitude in
determining vertical
flight path guidance.
Small Text
Altitude is not designated
to be used in determining
vertical flight path
guidance. Altitude has
been retrieved from the
navigation database and
is provided as a reference.
Altitude is designated
for use in giving vertical
flight path guidance.
Altitude has been
retrieved from the
navigation database
or has been entered by
the pilot and matches a
published altitude in the
navigation database.
The system cannot
use this altitude in
determining vertical
flight path guidance.
Index
Appendix
Annun/
Alerts
Abnormal
Operation
Additional
Features
Hazard
Avoidance
Procedures
Flight
Planning
GPS Nav
AFCS
Nav/Com/
XPDR/Audio
EIS
Flight
Instruments
GPS Navigation
20
Garmin G1000 Cockpit Reference Guide for the Diamond DA42NG
Light Blue
Subdued Text
190-00963-04 Rev. A
Flight Planning
Flight
Instruments
FLIGHT PLANNING
TRIP PLANNING
Turn the large FMS Knob to select the ‘AUX’ page group.
2)
Turn the small FMS Knob to select the first rectangular page icon.
3)
The current ‘PAGE MODE’ is displayed at the top of the page: ‘AUTOMATIC’
or ‘MANUAL’. To change the page mode, press the AUTO or MANUAL
Softkey.
4)
For Direct-to planning:
EIS
1)
Nav/Com/
XPDR/Audio
AFCS
GPS Nav
a) Press the WPTS Softkey and verify that the starting waypoint field
indicates ‘P.POS’ (present position).
b) If necessary, press the MENU Key and select ‘Set WPT to Present
Position’ to display ‘P.POS’.
Flight
Planning
c) Press the ENT Key and the flashing cursor moves to the ending
waypoint field.
Procedures
d) Enter the identifier of the ending waypoint and press the ENT Key to
accept the waypoint.
Or:
Hazard
Avoidance
For point-to-point planning:
a) Enter the identifier of the starting waypoint.
Additional
Features
b) Once the waypoint’s identifier is entered, press the ENT Key to accept
the waypoint. The flashing cursor moves to the ending waypoint.
Abnormal
Operation
c) Again, enter the identifier of the ending waypoint.
d) Press the ENT Key to accept the waypoint.
Or:
Annun/
Alerts
For flight plan leg planning:
a) Press the FPL Softkey (at the bottom of the display).
Appendix
b) Turn the small FMS Knob to select the desired flight plan (already
stored in memory), by number.
c) Turn the large FMS Knob to highlight the ‘LEG’ field.
Index
190-00963-04 Rev. A
Garmin G1000 Cockpit Reference Guide for the Diamond DA42NG
21
Flight Planning
EIS
Flight
Instruments
d) Turn the small FMS Knob to select the desired leg of the flight plan, or
select ‘CUM’ to apply trip planning calculations to the entire flight plan.
Selecting ‘FPL 00’ displays the active flight plan. If an active flight plan
is selected, ‘REM’ is an available option to display planning data for the
remainder of the flight plan.
Nav/Com/
XPDR/Audio
NOTE: The page mode must be set to ‘MANUAL’ to perform the following
steps.
AFCS
5)
Turn the large FMS Knob to highlight the departure time (DEP TIME) field.
Additional
Features
Hazard
Avoidance
Procedures
Flight
Planning
GPS Nav
NOTE: The departure time on the Trip Planning Page is used for preflight
planning. Refer to the Utility Page for the actual flight departure time.
6)
Enter the departure time. Press the ENT Key when finished. Departure time
may be entered in local or UTC time, depending upon system settings.
7)
The flashing cursor moves to the ground speed (GS) field. Enter the ground
speed. Press the ENT Key when finished. Note that in ‘automatic’ page
mode, ground speed is provided by the system.
8)
The flashing cursor moves to the fuel flow field. Enter the fuel flow. Press
the ENT Key when finished. Note that in ‘AUTOMATIC’ page mode, fuel flow
is provided by the system.
9)
The flashing cursor moves to the fuel onboard field. Enter the fuel onboard.
Press the ENT Key when finished. Note that in ‘AUTOMATIC’ page mode, fuel
onboard is provided by the fuel totalizer.
Abnormal
Operation
10) The flashing cursor moves to the calibrated airspeed (CALIBRATED AS) field.
Enter the calibrated airspeed. Press the ENT Key when finished. Note that
in ‘AUTOMATIC’ page mode, calibrated airspeed is provided by the system.
Annun/
Alerts
11) The flashing cursor moves to the altitude (IND ALTITUDE) field. Enter the
altitude. Press the ENT Key when finished. Note that in ‘AUTOMATIC’ page
mode, altitude is provided by the system.
Appendix
12) The flashing cursor moves to the barometric setting (PRESSURE) field. Enter
the desired baro setting. Press the ENT Key when finished. Note that in
‘AUTOMATIC’ page mode, the baro setting is provided by the setting entered
on the PFD.
Index
13) The flashing cursor moves to the air temperature (TOTAL AIR TEMP) field. Enter
the desired air temperature. Press the ENT Key when finished. Note that in
‘AUTOMATIC’ page mode, air temperature is provided by the system outside
air temperature.
22
Garmin G1000 Cockpit Reference Guide for the Diamond DA42NG
190-00963-04 Rev. A
Flight Planning
Turn the large FMS Knob on the Control Unit to select the ‘WPT’ page group.
2)
Turn the small FMS Knob to select the User WPT Information Page.
3)
Press the NEW Softkey. A waypoint is created at the current aircraft
position.
4)
Enter the desired waypoint name.
5)
Press the ENT Key.
6)
The cursor is now in the ‘WAYPOINT TYPE’ field. If desired, the waypoint
can be made temporary (deleted automatically when the system is turned
off). If the waypoint is to remain in the system, proceed to step 7.
EIS
1)
Nav/Com/
XPDR/Audio
AFCS
GPS Nav
a) Turn the large FMS Knob one click to the left to highlight
‘TEMPORARY’.
8)
Turn the small FMS Knob to select LAT/LON (latitude and longitude).
9)
Press the ENT Key.
CREATE A USER WAYPOINT DEFINED BY RADIALS FROM OTHER WAYPOINTS
2)
Turn the small FMS Knob to select the User WPT Information Page.
3)
Press the NEW Softkey. A waypoint is created at the current aircraft
position.
4)
Enter the desired waypoint name.
5)
Press the ENT Key.
6)
The cursor is now in the ‘WAYPOINT TYPE’ field. If desired, the waypoint
can be made temporary (deleted automatically when the system is turned
off). If the waypoint is to remain in the system, proceed to step 7.
Abnormal
Operation
Turn the large FMS Knob on the Control Unit to select the ‘WPT’ page group.
Annun/
Alerts
Appendix
Index
a) Turn the large FMS Knob one click to the left to highlight
‘TEMPORARY’.
b) Press the ENT Key to place a check-mark in the box. Turn the large
FMS Knob to place the cursor back in the ‘WAYPOINT TYPE’ field.
Garmin G1000 Cockpit Reference Guide for the Diamond DA42NG
Additional
Features
1)
Hazard
Avoidance
With the cursor in the ‘WAYPOINT TYPE’ field, turn the small FMS Knob to
display a list of waypoint types.
Procedures
7)
Flight
Planning
b) Press the ENT Key to place a check-mark in the box. Turn the large
FMS Knob to place the cursor back in the ‘WAYPOINT TYPE’ field.
190-00963-04 Rev. A
Flight
Instruments
CREATE A USER WAYPOINT DEFINED BY LATITUDE & LONGITUDE
23
EIS
Flight
Instruments
Flight Planning
7)
With the cursor in the ‘WAYPOINT TYPE’ field, turn the small FMS Knob to
display a list of waypoint types.
8)
Turn the small FMS Knob to select RAD/RAD (radial/radial).
9)
Press the ENT Key.
Nav/Com/
XPDR/Audio
10) The cursor moves to the ‘REFERENCE WAYPOINTS’ field. With the first
waypoint name highlighted, use the FMS Knobs to enter the desired
waypoint name. Waypoints may also be selected as follows:
AFCS
a) When a flight plan is active, turning the small FMS Knob to the left will
display a list of the flight plan waypoints.
b) Turn the large FMS Knob to select the desired waypoint.
GPS Nav
c) Press the ENT Key.
Or:
Flight
Planning
a) Turn the small FMS Knob to the left. Initially, a flight plan waypoint list
is displayed.
Procedures
b) Turn the small FMS Knob to the right to display the ‘NRST’ airports to
the aircraft’s current position.
c) Turn the large FMS Knob to select the desired waypoint.
d) Press the ENT Key.
Hazard
Avoidance
Or:
Additional
Features
a) Turn the small FMS Knob to the left. Initially, a flight plan waypoint list
is displayed.
b) Turn the small FMS Knob to the right to display the ‘RECENT’
waypoints.
Abnormal
Operation
c) Turn the large FMS Knob to select the desired waypoint.
d) Press the ENT Key.
Annun/
Alerts
Or:
a) Turn the small FMS Knob to the left. Initially, a flight plan waypoint list
is displayed.
Appendix
b) Turn the small FMS Knob to the right to display the ‘USER’ waypoints.
c) Turn the large FMS Knob to select the desired waypoint.
Index
d) Press the ENT Key.
11) Press the ENT Key. The cursor is displayed in the ‘RAD’ (radial) field. Enter
the desired radial from the reference waypoint.
24
Garmin G1000 Cockpit Reference Guide for the Diamond DA42NG
190-00963-04 Rev. A
Flight Planning
13) Repeat step 10 to enter the next waypoint name.
15) Press the ENT Key.
Nav/Com/
XPDR/Audio
16) Press the FMS Knob to remove the flashing cursor.
Press the NEW Softkey. A waypoint is created at the current aircraft
position.
4)
Enter the desired waypoint name.
5)
Press the ENT Key.
6)
The cursor is now in the ‘WAYPOINT TYPE’ field. If desired, the waypoint
can be made temporary (deleted automatically when the system is turned
off). If the waypoint is to remain in the system, proceed to step 7.
Hazard
Avoidance
3)
Procedures
Turn the small FMS Knob to select the User WPT Information Page.
Flight
Planning
2)
GPS Nav
Turn the large FMS Knob on the MFD Control Unit to select the ‘WPT’ page
group.
AFCS
CREATE A USER WAYPOINT DEFINED BY A RADIAL & DISTANCE FROM
ANOTHER WAYPOINT
1)
a) Turn the large FMS Knob one click to the left to highlight
‘TEMPORARY’.
Additional
Features
b) Press the ENT Key to place a check-mark in the box. Turn the large
FMS Knob to place the cursor back in the ‘WAYPOINT TYPE’ field.
8)
Turn the small FMS Knob to select RAD/DIS (radial/distance).
9)
Press the ENT Key.
Annun/
Alerts
With the cursor in the ‘WAYPOINT TYPE’ field, turn the small FMS Knob to
display a list of waypoint types.
b) Turn the large FMS Knob to select the desired waypoint.
c) Press the ENT Key.
25
Index
a) When a flight plan is active, turning the small FMS Knob to the left will
display a list of the flight plan waypoints.
Appendix
10) The cursor moves to the ‘REFERENCE WAYPOINTS’ field. With the first
waypoint name highlighted, use the FMS Knobs to enter the desired
waypoint name. Waypoints may also be selected as follows:
Garmin G1000 Cockpit Reference Guide for the Diamond DA42NG
Abnormal
Operation
7)
190-00963-04 Rev. A
EIS
14) Press the ENT Key. The cursor is displayed in the ‘RAD’ (radial) field for the
second waypoint. Enter the desired radial from the reference waypoint.
Flight
Instruments
12) Press the ENT Key.
Flight Planning
Flight
Instruments
Or:
a) Turn the small FMS Knob to the left. Initially, a flight plan waypoint list
is displayed.
EIS
b) Turn the small FMS Knob to the right to display the ‘NRST’ airports to
the aircraft’s current position.
Nav/Com/
XPDR/Audio
c) Turn the large FMS Knob to select the desired waypoint.
d) Press the ENT Key.
Or:
AFCS
a) Turn the small FMS Knob to the left. Initially, a flight plan waypoint list
is displayed.
GPS Nav
b) Turn the small FMS Knob to the right to display the ‘RECENT’
waypoints.
c) Turn the large FMS Knob to select the desired waypoint.
Flight
Planning
d) Press the ENT Key.
Or:
Procedures
a) Turn the small FMS Knob to the left. Initially, a flight plan waypoint list
is displayed.
Hazard
Avoidance
b) Turn the small FMS Knob to the right to display the ‘USER’ waypoints.
c) Turn the large FMS Knob to select the desired waypoint.
d) Press the ENT Key.
Additional
Features
11) Press the ENT Key. The cursor is displayed in the ‘RAD’ (radial) field. Enter
the desired radial from the reference waypoint.
Abnormal
Operation
12) Press the ENT Key.
13) The cursor is now displayed in the ‘DIS’ (distance) field. Enter the desired
distance from the reference waypoint.
15) Press the FMS Knob to remove the flashing cursor.
DELETE A USER WAYPOINT
Index
Appendix
Annun/
Alerts
14) Press the ENT Key.
26
1)
Turn the large FMS Knob to select the ‘WPT’ page group.
2)
Turn the small FMS Knob to select the User WPT Information Page.
3)
Press the FMS Knob to activate the cursor.
Garmin G1000 Cockpit Reference Guide for the Diamond DA42NG
190-00963-04 Rev. A
Flight Planning
Turn the small FMS Knob to highlight the desired waypoint.
6)
Press the DELETE Softkey.
7)
The message ‘Would you like to delete the user waypoint?’ is displayed. With
‘YES’ highlighted, press the ENT Key.
CREATE A FLIGHT PLAN
Flight
Planning
Procedures
Hazard
Avoidance
Additional
Features
Abnormal
Operation
Annun/
Alerts
Appendix
Creating a stored flight plan:
1) Press the FPL Key.
2) Turn the small FMS Knob clockwise to display the Flight Plan Catalog Page.
3) Press the NEW Softkey; or press the MENU Key, highlight ‘Create New
Flight Plan’, and press the ENT Key to display a blank flight plan for the
first empty storage location.
GPS Nav
Creating an active flight plan:
1) Press the FPL Key.
2) Press the FMS Knob to activate the cursor (only on MFD).
3) Turn the small FMS Knob to display the Waypoint Information Window.
(Turning it clockwise displays a blank Waypoint Information Window,
turning it counter-clockwise displays the Waypoint Information Window
with a waypoint selection submenu allowing selection of active flight plan,
nearest, recent, user, or airway waypoints).
4) Enter the identifier, facility, or city name of the departure waypoint or select
a waypoint from the submenu of waypoints and press the ENT Key. The
active flight plan is modified as each waypoint is entered.
5) Repeat step numbers 3 and 4 to enter each additional flight plan waypoint.
6) When all waypoints have been entered, press the FMS Knob to remove the
cursor.
AFCS
NOTE: When creating a flight plan in the Active Flight Plan Window, the first
leg is activated automatically after it is created.
Nav/Com/
XPDR/Audio
5)
EIS
Turn the large FMS Knob to the place the cursor in the ‘USER WAYPOINT LIST’
field.
Flight
Instruments
4)
Index
190-00963-04 Rev. A
Garmin G1000 Cockpit Reference Guide for the Diamond DA42NG
27
4)
Turn the small FMS Knob to display the Waypoint Information Window.
(Turning it clockwise displays a blank Waypoint Information Window,
turning it counter-clockwise displays the Waypoint Information Window
with a waypoint selection submenu allowing selection of active flight plan,
nearest, recent, user, or airway waypoints).
5)
Enter the identifier, facility, or city name of the departure waypoint or select
a waypoint from the submenu of waypoints and press the ENT Key.
6)
Repeat step numbers 4 and 5 to enter each additional flight plan waypoint.
7)
When all waypoints have been entered, press the FMS Knob to return to
the Flight Plan Catalog Page. The new flight plan is now in the list.
AFCS
Nav/Com/
XPDR/Audio
EIS
Flight
Instruments
Flight Planning
Hazard
Avoidance
Procedures
Flight
Planning
GPS Nav
IMPORT A FLIGHT PLAN FROM AN SD CARD
1)
Insert the SD card containing the flight plan in the top card slot on the MFD.
2)
Press the FPL Key on the Control Unit to display the Active Flight Plan Page
on the MFD.
3)
Turn the small FMS Knob to select the Flight Plan Catalog Page.
4)
Press the FMS Knob to activate the cursor.
5)
Turn either FMS Knob to highlight an empty or existing flight plan.
6)
Press the IMPORT Softkey.
If an empty flight plan is selected, a list of the available flight plans on the
SD card will be displayed.
Additional
Features
Or:
7)
Turn the small FMS Knob to highlight the desired flight plan for importing.
8)
Press the ENT Key.
Index
Appendix
Annun/
Alerts
Abnormal
Operation
If an existing flight plan is selected, an ‘Overwrite existing flight plan? OK
or CANCEL’ prompt is displayed. Press the ENT Key to choose to overwrite
the selected flight plan and see a list of the available flight plans on the SD
card. If overwriting the existing flight plan is not desired, select ‘CANCEL’
using the FMS Knob, press the ENT Key, select another existing or empty
flight plan, and again press the IMPORT Softkey.
28
Garmin G1000 Cockpit Reference Guide for the Diamond DA42NG
190-00963-04 Rev. A
Flight Planning
1)
Press the FPL Key to display the active flight plan.
2)
If required, press the FMS Knob to activate the cursor.
3)
Turn the large FMS Knob to highlight the desired flight plan waypoint. The
new waypoint is inserted before the highlighted waypoint.
EIS
4)
Turn the small FMS Knob. The Waypoint Information Window is now
displayed.
Nav/Com/
XPDR/Audio
Flight
Instruments
INSERT A WAYPOINT IN THE ACTIVE FLIGHT PLAN
5)
Enter the new flight plan waypoint by one of the following:
AFCS
a) Enter the user waypoint identifier, facility, or city.
b) Press the ENT Key.
b) Turn the small FMS Knob to the right to display the ‘NRST’ airport
waypoints to the aircraft’s current position.
Flight
Planning
a) Turn the small FMS Knob to the left. Initially, a flight plan waypoint list
is displayed.
GPS Nav
Or:
Procedures
c) Turn the large FMS Knob to select the desired waypoint.
d) Press the ENT Key.
a) Turn the small FMS Knob to the left. Initially, a flight plan waypoint list
is displayed.
Hazard
Avoidance
Or:
Additional
Features
b) Turn the small FMS Knob to the right to display the ‘RECENT’
waypoints.
Abnormal
Operation
c) Turn the large FMS Knob to select the desired waypoint.
d) Press the ENT Key.
e) Press the ENT Key again to accept the waypoint.
Annun/
Alerts
ENTER AN AIRWAY IN A FLIGHT PLAN
Press the FPL Key.
2)
Press the FMS Knob to activate the cursor (not required on the PFD).
3)
Turn the large FMS Knob to highlight the waypoint after the desired airway
entry point. If this waypoint is not a valid airway entry point, a valid entry
point should be entered at this time.
Garmin G1000 Cockpit Reference Guide for the Diamond DA42NG
29
Index
190-00963-04 Rev. A
Appendix
1)
4)
Turn the small FMS Knob one click clockwise and press the LD AIRWY
Softkey, or press the MENU Key and select “Load Airway”. The Select
Airway Page is displayed. The LD AIRWY Softkey or the “Load Airway”
menu item is available only when an acceptable airway entry waypoint has
been chosen (the waypoint ahead of the cursor position).
5)
Turn the FMS Knob to select the desired airway from the list, and press the
ENT Key. Low altitude airways are shown first in the list, followed by “all”
altitude airways, and then high altitude airways.
6)
Turn the FMS Knob to select the desired airway exit point from the list, and
press the ENT Key. ‘LOAD?’ is highlighted.
7)
Press the ENT Key. The system returns to editing the flight plan with the
new airway inserted.
USER-DEFINED HOLDING PATTERNS
A holding pattern can be defined at any active flight plan waypoint, or at the aircraft
present position.
Creating a user-defined hold at an active flight plan waypoint:
Index
Appendix
Annun/
Alerts
Abnormal
Operation
Additional
Features
Hazard
Avoidance
Procedures
Flight
Planning
GPS Nav
AFCS
Nav/Com/
XPDR/Audio
EIS
Flight
Instruments
Flight Planning
1)
Press the FPL Key to display the Active Flight Plan Page (MFD) or the Active
Flight Plan Window (PFD).
2)
Press the FMS Knob to activate the cursor (not required on the PFD) and
turn the large FMS Knob to highlight the waypoint for the hold.
3)
Press the MENU Key, highlight ‘Hold At Wpt’, and press the ENT Key. The
HOLD AT window appears with the course field highlighted.
4)
Use the FMS Knobs to edit the entry course, and press the ENT Key.
5)
Use the small FMS Knob to select ‘INBOUND’ or ‘OUTBOUND’ course
direction, and press the ENT Key.
6)
Use the small FMS Knob to select ‘TIME’ or ‘DIST’ length mode, and press
the ENT Key.
7)
Use the FMS Knobs to edit the length, and press the ENT Key.
8)
Use the small FMS Knob to select ‘RIGHT’ or ‘LEFT’ turn direction, and
press the ENT Key.
9)
Use the FMS Knobs to edit the Expect Further Clearance Time (EFC TIME),
and press the ENT Key.
10) Press the ENT Key while ‘LOAD?’ is highlighted to add the hold into the
flight plan.
30
Garmin G1000 Cockpit Reference Guide for the Diamond DA42NG
190-00963-04 Rev. A
Flight Planning
Press the MENU Key, highlight ‘Hold At Present Position’, and press the
ENT Key. The HOLD AT window appears with the Length mode highlighted.
3)
Use the small FMS Knob to select ‘TIME’ or ‘DIST’ length mode, and press
the ENT Key.
4)
Use the FMS Knobs to edit the length, and press the ENT Key.
5)
Use the small FMS Knob to select ‘RIGHT’ or ‘LEFT’ turn direction, and
press the ENT Key.
6)
Use the FMS Knobs to edit the Expect Further Clearance Time (EFC TIME),
and press the ENT Key.
7)
Press the ENT Key while ‘ACTIVATE?’ is highlighted to immediately activate
the hold.
AFCS
2)
Nav/Com/
XPDR/Audio
Press the FPL Key to display the Active Flight Plan Page (MFD) or the Active
Flight Plan Window (PFD).
EIS
1)
Flight
Instruments
Creating a user-defined hold at the aircraft present position:
GPS Nav
Flight
Planning
Creating a user-defined hold at a Direct-To waypoint:
Procedures
Press a Direct-to Key and set up the Direct To waypoint as desired, but
select ‘HOLD?’ instead of ‘ACTIVATE?’ when finished.
2)
Use the FMS Knobs to edit the entry course, and press the ENT Key.
5)
Use the small FMS Knob to select ‘INBOUND’ or ‘OUTBOUND’ course
direction, and press the ENT Key.
6)
Use the small FMS Knob to select ‘TIME’ or ‘DIST’ length mode, and press
the ENT Key.
7)
Use the FMS Knobs to edit the length, and press the ENT Key.
8)
Use the small FMS Knob to select ‘RIGHT’ or ‘LEFT’ turn direction, and
press the ENT Key.
9)
Use the FMS Knobs to edit the Expect Further Clearance Time (EFC TIME),
and press the ENT Key.
Hazard
Avoidance
1)
Additional
Features
Abnormal
Operation
Annun/
Alerts
Appendix
10) Press the ENT Key while ‘ACTIVATE?’ is highlighted to activate the Direct To
with the user-defined hold defined at the Direct To waypoint.
Index
190-00963-04 Rev. A
Garmin G1000 Cockpit Reference Guide for the Diamond DA42NG
31
Flight Planning
Nav/Com/
XPDR/Audio
EIS
Flight
Instruments
Removing a user-defined hold (created at the aircraft present position
or at a Direct-To waypoint):
2)
Press the MENU Key to display the PAGE MENU with the cursor on the
‘Cancel Direct To NAV’ selection.
3)
Press the ENT Key. The holding pattern is removed.
AFCS
GPS Nav
Flight
Planning
Procedures
1)
Press the FPL Key to display the Active Flight Plan Page (MFD) or the Active
Flight Plan Window (PFD).
2)
Press the FMS Knob to activate the cursor (not required on the PFD) and
turn the large FMS Knob to highlight the HOLD waypoint.
3)
Press the CLR Key. A ‘Remove Holding Pattern?’ confirmation window is
displayed.
4)
Select ‘OK’ and press the ENT Key. The holding pattern is removed from
the active flight plan. Select ‘CANCEL’ and press the ENT Key to cancel the
removal of the holding pattern.
INVERT AN ACTIVE FLIGHT PLAN
Abnormal
Operation
Additional
Features
Hazard
Avoidance
Press the Direct To Key to display the DIRECT TO Window (PFD or MFD).
Removing a user-defined hold (created at an active flight plan
waypoint):
1)
Press the FPL Key to display the active flight plan.
2)
Press the MENU Key to display the Page Menu.
3)
Turn the large FMS Knob to highlight ‘Invert Flight Plan’.
4)
Press the ENT Key. The original flight plan remains intact in its flight plan
catalog storage location.
5)
With ‘OK’ highlighted, press the ENT Key to invert the flight plan.
REMOVE A DEPARTURE, ARRIVAL, APPROACH, OR AIRWAY FROM A FLIGHT
PLAN
Appendix
Annun/
Alerts
1)
1)
Press the FPL Key to display the active flight plan. Press the FMS Knob to
activate the cursor.
Index
Or, for a stored flight plan:
a) Press the FPL Key on the MFD.
b) Turn the small FMS Knob to select the Flight Plan Catalog Page.
32
Garmin G1000 Cockpit Reference Guide for the Diamond DA42NG
190-00963-04 Rev. A
Flight Planning
Flight
Instruments
c) Press the FMS Knob to activate the cursor.
d) Turn the large FMS Knob to highlight the desired flight plan.
e) Press the EDIT Softkey.
Press the CLR Key to display a confirmation window.
4)
With ‘OK’ highlighted, press the ENT Key to remove the selected procedure
or airway.
STORE A FLIGHT PLAN
2)
Turn the large FMS Knob to highlight ‘Store Flight Plan’ and press the ENT Key.
3)
With ‘OK’ highlighted, press the ENT Key to store the flight plan.
2)
Press the FMS Knob to activate the cursor.
3)
Turn the large FMS Knob to highlight the desired flight plan.
4)
Press the EDIT Softkey.
5)
Turn the large FMS Knob to place the cursor in the desired location.
6)
Enter the changes, then press the ENT Key.
7)
Press the FMS Knob to return to the Flight Plan Catalog Page.
Additional
Features
Press the FPL Key on the MFD and turn the small FMS Knob to display the
Flight Plan Catalog Page.
Abnormal
Operation
Or, for a stored flight plan:
Appendix
Press the FPL Key to display the active flight plan. Press the FMS Knob to
activate the cursor.
Annun/
Alerts
DELETE A WAYPOINT FROM THE FLIGHT PLAN
1)
Hazard
Avoidance
1)
Procedures
EDIT A STORED FLIGHT PLAN
Flight
Planning
After creating a flight plan on either the PFD or MFD, it may be saved by
pressing the MENU Key.
GPS Nav
1)
AFCS
3)
Nav/Com/
XPDR/Audio
Turn the large FMS Knob to highlight the title for the approach, departure,
arrival, or airway to be deleted. Titles appear in white directly above the
procedure’s waypoints.
EIS
2)
a) Press the FPL Key on the MFD.
Index
b) Turn the small FMS Knob to select the Flight Plan Catalog Page.
c) Press the FMS Knob to activate the cursor.
190-00963-04 Rev. A
Garmin G1000 Cockpit Reference Guide for the Diamond DA42NG
33
Flight Planning
Flight
Instruments
d) Turn the large FMS Knob to highlight the desired flight plan.
Flight
Planning
Procedures
Annun/
Alerts
Abnormal
Operation
Additional
Features
Hazard
Avoidance
Turn the large FMS Knob to highlight the waypoint to be deleted.
3)
Press the CLR Key to display a ‘REMOVE (Wpt Name)?’ confirmation window.
4)
With ‘OK’ highlighted, press the ENT Key to remove the waypoint. To cancel
the delete request, turn the large FMS Knob to highlight ‘CANCEL’ and press
the ENT Key.
5)
Once all changes have been made, press the FMS Knob to remove the cursor.
1)
Press the FPL Key on the MFD.
2)
Turn the small FMS Knob to select the Flight Plan Catalog Page.
3)
Press the FMS Knob to activate the cursor.
4)
Turn the large FMS Knob to highlight the desired flight plan.
5)
Press the INVERT Softkey. ‘Invert and activate stored flight plan?’ is
displayed.
6)
With ‘OK’ highlighted, press the ENT Key. The selected flight plan is now
inverted and activated. The original flight plan remains intact in its flight plan
catalog storage location.
COPY A FLIGHT PLAN
1)
Press the FPL Key on the MFD.
2)
Turn the small FMS Knob to select the Flight Plan Catalog Page.
3)
Press the FMS Knob to activate the cursor.
4)
Turn the large FMS Knob to highlight the flight plan to be copied.
5)
Press the COPY Softkey. A ‘Copy to flight plan #?’ confirmation window is
displayed.
6)
With ‘OK’ highlighted, press the ENT Key to copy the flight plan. To cancel,
turn the large FMS Knob to highlight ‘CANCEL’ and press the ENT Key.
DELETE A FLIGHT PLAN
Index
Appendix
2)
INVERT AND ACTIVATE A STORED FLIGHT PLAN
GPS Nav
AFCS
Nav/Com/
XPDR/Audio
EIS
e) Press the EDIT Softkey.
34
1)
Press the FPL Key on the MFD.
2)
Turn the small FMS Knob to select the Flight Plan Catalog Page.
Garmin G1000 Cockpit Reference Guide for the Diamond DA42NG
190-00963-04 Rev. A
Flight Planning
Turn the large FMS Knob to highlight the flight plan to be deleted.
5)
Press the DELETE Softkey. A ‘Delete flight plan #?’ confirmation window is
displayed.
6)
With ‘OK’ highlighted, press the ENT Key to delete the flight plan. To cancel,
turn the large FMS Knob to highlight ‘CANCEL’ and press the ENT Key.
GRAPHICAL FLIGHT PLAN CREATION
Nav/Com/
XPDR/Audio
4)
EIS
Press the FMS Knob to activate the cursor.
Flight
Instruments
3)
Press the FPL Key to display the Active Flight Plan Page on the MFD.
2)
Press the Joystick to activate the map pointer. Use the Joystick to move
the pointer to the desired point on the map to be inserted as a waypoint in
the flight plan.
3)
The default insertion point is at the end of the flight plan. If the selected
waypoint is to be placed anywhere other than the end of the flight plan,
press the FMS Knob to activate the cursor. Waypoints are inserted ABOVE
the cursor. Turn the large FMS Knob to select the desired insertion point.
4)
Press the LD WPT Softkey. The selected waypoint is inserted at the selected
point. The default user waypoint naming is USR000, USR001, USR002, and
so on.
Procedures
5)
To change the user waypoint name, follow the procedure for modifying a user
waypoint.
Hazard
Avoidance
GPS Nav
Flight
Planning
Additional
Features
EXPORT A FLIGHT PLAN TO AN SD CARD
AFCS
1)
2)
Press the FPL Key on the Contol Unit to display the Active Flight Plan Page
on the MFD.
3)
Turn the small FMS Knob to select the Flight Plan Catalog Page.
4)
Press the FMS Knob to activate the cursor.
5)
Turn the large FMS Knob to highlight the flight plan to be exported.
6)
Press the EXPORT Softkey.
7)
Press the ENT Key to confirm the export.
Annun/
Alerts
Insert the SD card into the top card slot on the MFD.
Abnormal
Operation
1)
Appendix
Index
190-00963-04 Rev. A
Garmin G1000 Cockpit Reference Guide for the Diamond DA42NG
35
Index
Appendix
Annun/
Alerts
Abnormal
Operation
Additional
Features
Hazard
Avoidance
Procedures
Flight
Planning
GPS Nav
AFCS
Nav/Com/
XPDR/Audio
EIS
Flight
Instruments
Flight Planning
Blank Page
36
Garmin G1000 Cockpit Reference Guide for the Diamond DA42NG
190-00963-04 Rev. A
Procedures
Flight
Instruments
PROCEDURES
LOAD AND ACTIVATE A DEPARTURE PROCEDURE
EIS
3)
Press the ENT Key. The cursor is displayed in the ‘DEPARTURE’ field with a
list of available departures.
4)
Turn the large FMS Knob to highlight the desired departure.
5)
Press the ENT Key. A list of runways may be displayed for the departure. If
so, turn either FMS Knob to select the desired runway.
6)
Press the ENT Key. The cursor is displayed in the ‘TRANSITION’ field with a
list of available transitions.
7)
Turn the large FMS Knob to highlight the desired transition.
8)
Press the ENT Key.
9)
With ‘LOAD?’ highlighted, press the ENT Key. The departure is active when
the flight plan is active.
Flight
Planning
Turn the large FMS Knob to highlight ‘SELECT DEPARTURE’.
Hazard
Avoidance
Press the FPL Key on the MFD to display the active flight plan.
2)
Press the FMS Knob to activate the cursor.
3)
Turn the large FMS Knob to highlight the desired waypoint within the
departure.
4)
Press the ACT LEG Softkey. A confirmation window showing the selected
leg is displayed.
5)
With ‘ACTIVATE’ highlighted, press the ENT Key.
Additional
Features
1)
Abnormal
Operation
Annun/
Alerts
LOAD AN ARRIVAL PROCEDURE
Appendix
Press the PROC Key.
2)
Turn the large FMS Knob to highlight ‘SELECT ARRIVAL’.
3)
Press the ENT Key. The cursor is displayed in the ‘ARRIVAL’ field with a list
of available arrivals.
37
Index
1)
Garmin G1000 Cockpit Reference Guide for the Diamond DA42NG
Procedures
ACTIVATE A DEPARTURE LEG
190-00963-04 Rev. A
GPS Nav
2)
AFCS
Press the PROC Key.
Nav/Com/
XPDR/Audio
1)
Nav/Com/
XPDR/Audio
EIS
Flight
Instruments
Procedures
4)
Turn the large FMS Knob to highlight the desired arrival.
5)
Press the ENT Key. A list of transitions is displayed for the selected arrival.
6)
Turn either FMS Knob to select the desired transition.
7)
Press the ENT Key. A list of runways may be displayed for the selected
arrival.
8)
Turn the large FMS Knob to highlight the desired runway.
9)
Press the ENT Key.
10) With ‘LOAD?’ highlighted, press the ENT Key.
AFCS
11) The arrival becomes part of the active flight plan.
GPS Nav
12) If an altitude associated with a waypoint in an arrival procedure is to be
used to calculate vertical guidance perform the following steps:
a) Press the FMS Knob to activate the cursor.
c) Press the ENT Key to designate the altitude for use in giving vertical
guidance.
ACTIVATE AN ARRIVAL LEG
1)
Press the FPL Key to display the active flight plan.
2)
Press the FMS Knob to activate the cursor.
3)
Turn the large FMS Knob to highlight the desired waypoint within the
arrival.
4)
Press the ACT LEG Softkey. A confirmation window showing the selected
leg is displayed.
5)
With ‘ACTIVATE’ highlighted, press the ENT Key.
LOAD AND/OR ACTIVATE AN APPROACH PROCEDURE
NOTE: If certain GPS parameters (SBAS, RAIM, etc.) are not available, some
published approach procedures for the desired airport may not be displayed
in the list of available approaches.
Index
Appendix
Annun/
Alerts
Abnormal
Operation
Additional
Features
Hazard
Avoidance
Procedures
Flight
Planning
b) Turn the large FMS Knob to highlight the desired waypoint altitude.
38
1)
Press the PROC Key.
2)
Turn the large FMS Knob to highlight ‘SELECT APPROACH’.
Garmin G1000 Cockpit Reference Guide for the Diamond DA42NG
190-00963-04 Rev. A
Procedures
Press the ENT Key. A list of available approaches for the destination airport
is displayed.
4)
Turn either FMS Knob to highlight the desired approach.
5)
Press the ENT Key. A list of available transitions for the selected approach
procedure is now displayed.
EIS
6)
Turn either FMS Knob to select the desired transition. The “Vectors”
option assumes vectors will be received to the final course segment of
the approach and will provide navigation guidance relative to the final
approach course.
Nav/Com/
XPDR/Audio
7)
Press the ENT Key. The cursor moves to the MINIMUMS field.
8)
If desired, the DA/MDA for the selected approach procedure may be
entered and displayed on the PFD. Turn the small FMS Knob in the
direction of the green arrow to change the display from OFF to BARO, TEMP
COMP or optional RAD ALT.
9)
Press the ENT Key. The cursor moves to the altitude field. Turn the small
FMS Knob to enter the published DA/MDA for the selected approach
procedure.
Flight
Instruments
3)
AFCS
GPS Nav
Flight
Planning
Procedures
Hazard
Avoidance
10) Press the ENT Key. If BARO, or OFF was selected step 8, proceed to step
11. If TEMP COMP was selected in step 8, the cursor moves to the ‘TEMP
AT....” field. Turn the small FMS Knob to enter the temperature at the
destination airport. The temperature compensated altitude minimum is
displayed below the previously enter minimum altitude value.
Additional
Features
11) Press the ENT Key. ‘LOAD? or ACTIVATE?’ is now displayed with ‘LOAD?’
highlighted.
Abnormal
Operation
12) Turn the large FMS Knob to select either ‘LOAD?’ or ‘ACTIVATE?’.
Annun/
Alerts
Selecting ‘LOAD?’ enters the selected approach procedure into the active
flight plan, but is not currently active. Selecting ‘ACTIVATE?’ enters the
selected approach procedure into the active flight plan and activates the
first leg of the approach.
13) Press the ENT Key.
Appendix
Index
190-00963-04 Rev. A
Garmin G1000 Cockpit Reference Guide for the Diamond DA42NG
39
ACTIVATE AN APPROACH IN THE ACTIVE FLIGHT PLAN
Procedures
Flight
Planning
GPS Nav
2)
Turn the large FMS Knob to highlight ‘ACTIVATE APPROACH’.
3)
Press the ENT Key.
1)
Press the PROC Key.
2)
Turn the large FMS Knob to highlight ‘ACTIVATE VECTOR-TO-FINAL’.
3)
Press the ENT Key.
4)
The final approach course becomes the active leg.
ACTIVATE A MISSED APPROACH IN THE ACTIVE FLIGHT PLAN
1)
Press the PROC Key.
2)
Turn the large FMS Knob to highlight ‘ACTIVATE MISSED APPROACH’.
3)
Press the ENT Key. A confirmation window is displayed.
4)
With ‘ACTIVATE’ highlighted, press the ENT Key.
Or:
Hazard
Avoidance
Additional
Features
Press the PROC Key.
Press the Go-around Switch:
TEMPERATURE COMPENSATED ALTITUDE
When temperature compensated altitude is enabled for the loaded approach, the
altitudes associated with the approach waypoints are displayed in slanted text.
Appendix
Annun/
Alerts
Abnormal
Operation
1)
ACTIVATE A VECTOR TO FINAL APPROACH FIX
AFCS
Nav/Com/
XPDR/Audio
EIS
Flight
Instruments
Procedures
Index
Altitudes Displayed Without
Temperature Compensation
40
Altitudes Displayed With
Temperature Compensation
Garmin G1000 Cockpit Reference Guide for the Diamond DA42NG
190-00963-04 Rev. A
Procedures
EIS
Use the small FMS Knob to select the temperature at the <airport>. The
compensated altitude is computed as the temperature is selected.
Press the ENT Key. ‘ACTIVATE COMPENSATION?’ is highlighted.
6)
Press the ENT Key. The compensated altitudes for the approach are
AFCS
5)
GPS Nav
shown in the flight plan.
Flight
Planning
Disabling temperature compensated altitude:
1) From the Active Flight Plan Page, press the MENU Key. The Page Menu is
displayed.
2) Turn the FMS Knob to highlight ‘Temperature Compensation’.
3) Press the ENT Key. The TEMPERATURE COMPENSATION Window is
displayed.
4) Press the ENT Key. ‘CANCEL COMPENSATION?’ is highlighted.
Procedures
Press the ENT Key. The temperature compensated altitude at the FAF
is cancelled.
Hazard
Avoidance
5)
Nav/Com/
XPDR/Audio
4)
Flight
Instruments
Enabling temperature compensated altitude:
1) From the Active Flight Plan Page, press the MENU Key. The Page Menu is
displayed.
2) Turn the FMS Knob to highlight ‘Temperature Compensation’.
3) Press the ENT Key. The TEMPERATURE COMPENSATION Window is
displayed.
Additional
Features
Abnormal
Operation
Annun/
Alerts
Appendix
Index
190-00963-04 Rev. A
Garmin G1000 Cockpit Reference Guide for the Diamond DA42NG
41
Index
Appendix
Annun/
Alerts
Abnormal
Operation
Additional
Features
Hazard
Avoidance
Procedures
Flight
Planning
GPS Nav
AFCS
Nav/Com/
XPDR/Audio
EIS
Flight
Instruments
Procedures
Blank Page
42
Garmin G1000 Cockpit Reference Guide for the Diamond DA42NG
190-00963-04 Rev. A
Hazard Avoidance
Flight
Instruments
HAZARD AVOIDANCE
CUSTOMIZING THE HAZARD DISPLAYS ON THE NAVIGATION MAP
With the Navigation Map Page displayed, press the MENU Key to display
the Navigation Map Page Menu. The cursor flashes on the ‘Map Setup’
option.
2)
Press the ENT Key. The Map Setup Menu is displayed. Turn the small FMS
Knob to select ‘Weather’ to customize the display of weather features.
Select ‘Traffic’ to customize the display of traffic.
3)
Press the small FMS Knob to return to the Navigation Map Page.
EIS
1)
AFCS
GPS Nav
Procedures
Displaying Stormscope Lightning Data on the Navigation Map Page
Press the MAP Softkey.
2)
Press the STRMSCP Softkey. Press the STRMSCP Softkey again to remove
Stormscope Lightning Data from the Navigation Map Page.
Additional
Features
Symbol
Abnormal
Operation
Strike is between 6 and 60 seconds old
Annun/
Alerts
Strike is between 1 and 2 minutes old
Strike is between 2 and 3 minutes old
Turn either FMS Knob to highlight ‘Map Setup’.
3)
Press the ENT Key.
4)
Turn the small FMS Knob to highlight ‘Weather’.
190-00963-04 Rev. A
Garmin G1000 Cockpit Reference Guide for the Diamond DA42NG
Index
2)
Appendix
Select ‘Cell’ or ‘Strike’ as the Stormscope Lightning Mode
Press the MENU Key (with the Navigation Map Page displayed).
Hazard
Avoidance
1)
1)
Flight
Planning
WARNING: The Stormscope system is not intended to be used for hazardous
thunderstorm penetration. Weather information on the G1000 MFD is
approved for weather avoidance only. Refer to the WX-500 Pilot’s Guide for
detailed operation.
Lightning Age
Strike is less than 6 seconds old
Nav/Com/
XPDR/Audio
STORMSCOPE® (OPTIONAL)
43
Nav/Com/
XPDR/Audio
EIS
Flight
Instruments
Hazard Avoidance
5)
Press the ENT Key.
6)
Turn the large FMS Knob to place the cursor in the ‘STRMSCP MODE’ field.
7)
Turn the small FMS Knob to display the ‘Cell/Strike’ window.
8)
Turn either FMS Knob to select ‘Cell’ or ‘Strike’. Press the ENT Key.
9)
Push the FMS Knob to return to the Navigation Map Page.
AFCS
Clear Stormscope Lightning Data from the Navigation Map Page
1)
Press the MENU Key (with the Navigation Map Page displayed).
2)
Turn either FMS Knob to highlight the ‘Clear Stormscope® Lightning’ field
and press the ENT Key.
GPS Nav
NOTE: If heading input is lost, strikes and/or cells must be cleared manually
Flight
Planning
after the execution of each turn. This is to ensure that the strike and/or cell
positions are depicted accurately in relation to the nose of the aircraft.
Procedures
Stormscope Page
1)
Turn the large FMS Knob until the Map Page group is selected.
2)
Turn the small FMS Knob until the Stormscope Page is selected.
1)
Select the Stormscope Page.
2)
Press the MODE Softkey. The CELL and STRIKE Softkeys are displayed.
Press the CELL Softkey to display ‘CELL’ data or press the STRIKE Softkey
to display ‘STRIKE’ data. ‘CELL’ or ‘STRIKE’ is displayed in the mode box
located in the upper left corner of the Stormscope Page.
Abnormal
Operation
Additional
Features
Hazard
Avoidance
Change the Stormscope Lightning Mode Between ‘Cell’ and ‘Strike’
Annun/
Alerts
NOTE: “Cell mode” uses a clustering program to identify clusters of electrical
activity that indicate cells.
Appendix
Change the Viewing Mode Between 360˚ and 120˚
1)
Select the Stormscope Page.
2)
Press the VIEW Softkey. The 360 and ARC Softkeys are displayed. Press
the 360 Softkey to display a 360˚ viewing area or press the ARC Softkey to
display a 120˚ viewing area.
Index
Press the CLEAR Softkey to remove all Stormscope lightning data from the
display.
44
Garmin G1000 Cockpit Reference Guide for the Diamond DA42NG
190-00963-04 Rev. A
Hazard Avoidance
Press the MAP Softkey.
2)
Press the NEXRAD or XM LTNG Softkey to display the desired weather.
Press the applicable softkey again to remove weather data from the
Navigation Map Page.
AFCS
1)
Nav/Com/
XPDR/Audio
Displaying SiriusXM Weather on the Navigation Map Page
2)
Turn the small FMS Knob to select the Airport Information Page.
3)
Press the WX Softkey to display METAR and TAF text (METAR and TAF
information is updated every 12 minutes).
Flight
Planning
Turn the large FMS Knob to select the WPT Page Group.
GPS Nav
Display METAR and TAF information on the Airport Information Page
1)
Procedures
Displaying Weather on the Weather Data Link Page
2)
Turn the small FMS Knob to select the Weather Data Link Page.
3)
Press the available softkeys to select the desired SiriusXM Weather product.
4)
Press the LEGEND Softkey to view the legends for the selected products. If
necessary, turn either FMS Knob to scroll through the list. Press the small
FMS Knob or the ENT Key to return to the map.
Abnormal
Operation
Map Panning Information – Weather Data Link Page
Push in the Joystick to display the panning arrow.
2)
Move the Joystick to place the panning arrow on AIRMETs, TFRs, METARs,
or SIGMETs.
3)
Press the ENT Key to display pertinent information for the selected product.
Annun/
Alerts
1)
Appendix
Index
Note that pressing the ENT Key when panning over an AIRMET or a
SIGMET displays an information box that shows the text of the report.
Panning over an airport with METAR information does not display more
information but allows the user to press the ENT Key and select that
Airport’s Information Page to display the text of the report. Pressing the
ENT Key when panning over a TFR displays TFR specific information.
Garmin G1000 Cockpit Reference Guide for the Diamond DA42NG
Additional
Features
Turn the large FMS Knob to select the Map Page Group.
Hazard
Avoidance
1)
190-00963-04 Rev. A
EIS
WARNING: Do not use data link weather information for maneuvering in, near,
or around areas of hazardous weather. Information contained within data
link weather products may not accurately depict current weather conditions.
Flight
Instruments
SIRIUSXM WEATHER (OPTIONAL)
45
Hazard Avoidance
Flight
Instruments
SiriusXM Weather Products and Symbols
GPS Nav
AFCS
Nav/Com/
XPDR/Audio
EIS
SiriusXM Weather Product
Flight
Planning
Procedures
Hazard
Avoidance
Additional
Features
Abnormal
Operation
Annun/
Alerts
Broadcast
Rate
(Minutes)
5 (U.S.)
10 (Canada)
15 (69/69A)
30 (69/69A
SXM)
Next-generation Radar
(NEXRAD)
30
Cloud Top
(CLD TOP)
60
Echo Top
(ECHO TOP)
30
7.5
30
5
30
12
60
12
90
12
90
12
60
12
120
12
90
12
60
5
60
12
SiriusXM Lightning
(XM LTNG)
Cell Movement
(CELL MOV)
SIGMETs/AIRMETs
(SIG/AIR)
Meteorological Aerodrome
Report
(METARs)
City Forecast
(CITY)
Surface Analysis
(SFC)
Freezing Levels
(FRZ LVL)
Winds Aloft
(WIND)
County Warnings
(COUNTY)
Cyclone Warnings
(CYCLONE)
Index
Appendix
Symbol
Expiration
Time
(Minutes)
46
Garmin G1000 Cockpit Reference Guide for the Diamond DA42NG
190-00963-04 Rev. A
Hazard Avoidance
Symbol
90
12
90
12
180
12
30
5
60
12
60
12
AFCS
Flight
Planning
Procedures
no product
image
no product
image
no product
image
GPS Nav
Temporary Flight Restrictions
(TFRs)
Terminal Aerodrome Reports
(TAFs)
22
Nav/Com/
XPDR/Audio
No Radar Coverage
90
EIS
Icing Potential (CIP and SLD)
(ICNG)
Pilot Weather Report
(PIREPs)
Air Report
(AIREPs)
Turbulence
(TURB)
Broadcast
Rate
(Minutes)
Flight
Instruments
SiriusXM Weather Product
Expiration
Time
(Minutes)
SiriusXM Weather Product Symbols and Data Timing
Hazard
Avoidance
GARMIN CONNEXT WEATHER (OPTIONAL)
Abnormal
Operation
Annun/
Alerts
Weather data is provided when the pilot initiates either a manual or automatic
Connext Weather data request on the Connext Weather Data Link Page on the MFD.
No weather data is displayed until the first Connext Weather Data Request is made.
Additional
Features
WARNING: Do not use data link weather information for maneuvering in, near,
or around areas of hazardous weather. Information contained within data
link weather products may not accurately depict current weather conditions.
Registering with Garmin Connext
Garmin G1000 Cockpit Reference Guide for the Diamond DA42NG
47
Index
190-00963-04 Rev. A
Appendix
A subscriber account must be established prior to receiving Worldwide Weather
products. Contact Garmin Flight Data Services at https://fly.garmin.com/fly-garmin/
support/applications/satelliteservices/ or by calling 1-866-739-5687 in the United
States or (011) 913-440-1135.
After a subscriber account has been established, the system must be registered
for data link features such as reporting services or Connext Worldwide Weather.
Registration is accomplished by entering the required access code. This process is only
performed when initially setting up the system for Garmin Connext services.
Registering the System for Data Link Services
Hazard
Avoidance
Procedures
Flight
Planning
GPS Nav
AFCS
Nav/Com/
XPDR/Audio
EIS
Flight
Instruments
Hazard Avoidance
With the aircraft outside and having a clear view of the sky, turn the large
FMS Knob on the MFD to select the AUX page group.
2)
Turn the small FMS Knob to select the AUX-SYSTEM STATUS. Note the
System ID number in the AIRFRAME field.
3)
Turn the large FMS Knob to select the MAP Page group.
4)
Turn the small FMS Knob to select the MAP-WEATHER DATA LINK Page.
5)
Press the MENU Key. If necessary, select ‘Display Connext Weather’.
6)
Press ENT Key. The ‘GARMIN FLIGHT DATA SERVICE REGISTRATION’
Window is now displayed.
7)
Press the MENU Key. The Page Menu window is now displayed.
8)
Using the FMS Knob enter the access code obtained from Garmin Flight
Data Services in the ACCESS CODE field.
9)
Press the ENT Key. REGISTER will now be highlighted.
10) Press the ENT Key. System registration is complete when ‘REGISTERED’ is
displayed in the STATUS field.
Additional
Features
Abnormal
Operation
Annun/
Alerts
Appendix
Index
1)
Accessing Connext Weather Products
1)
Turn the large FMS Knob to select the Map Page Group.
2) Turn the small FMS Knob to select the Connext Weather Data Link Page.
When a weather product is selected for display on the Connext Weather Data Link
Page, a box containing a symbol for the product and its age (in minutes) are shown
in the upper right. If weather data has not been requested, ‘N/A’ is shown next to the
product symbol instead of age. The age of the weather product is based on the time
difference between when the data was assembled on the ground and the current GPS
time. Weather products are updated continuously or refreshed at specific intervals
(defined in the Refresh Rate column in the following table).
If for any reason, a weather product is not refreshed within the defined Expiration
Time intervals, the data is considered expired and is removed from the display. The
age of the expired product is replaced by dashes. If more than half of the expiration
48
Garmin G1000 Cockpit Reference Guide for the Diamond DA42NG
190-00963-04 Rev. A
Hazard Avoidance
Nav/Com/
XPDR/Audio
AFCS
GPS Nav
Flight
Planning
Procedures
Hazard
Avoidance
Additional
Features
Abnormal
Operation
Annun/
Alerts
Appendix
Index
Garmin G1000 Cockpit Reference Guide for the Diamond DA42NG
EIS
* The composite precipitation image is updated every 3 minutes, but individual radar sites may take
between 3 and 10 minutes to provide new data.
†
Canadian radar precipitation data provided by Environment Canada.
ˆ Australian radar precipitation data provided by the Australian Bureau of Meteorology.
Garmin Connext Weather Product Symbols and Data Timing
190-00963-04 Rev. A
Flight
Instruments
time has elapsed, the color of the product age readout changes to yellow.
The refresh rate represents the interval at which the Garmin Connext servers make
available the most current known weather data. It does not necessarily represent the
rate at which new content is received from weather sources.
Expiration Time
Garmin Connext
Refresh Rate
Symbol
(Minutes)
Weather Product
(Minutes)
U.S.: 3*
Canada: 3*†
Radar Precipitation
30
(PRECIP)
Europe: 15
Australia: 15ˆ
Infrared Satellite
60
30
(IR SAT)
Data Link Lightning
30
Continuous
(DL LTNG)
SIGMETs/AIRMETs
60
Continuous
(SIG/AIR)
Meteorological
Aerodrome Report
90
Continuous
(METARs)
Winds Aloft
90
Continuous
(WIND)
Pilot Weather Report
90
Continuous
(PIREPs)
Temporary Flight
no product
Restrictions
60
Continuous
image
(TFRs)
Terminal Aerodrome
no product
Forecasts
60
Continuous
image
(TAFs)
49
Hazard Avoidance
Flight
Planning
GPS Nav
AFCS
Nav/Com/
XPDR/Audio
EIS
Flight
Instruments
Setting Up and Customizing the Connext Weather Data Link Page
1)
Select the Connext Weather Data Link Page.
2)
Press the MENU Key.
3)
With ‘Weather Setup’ highlighted, press the ENT Key.
4)
Turn the small FMS Knob to select ‘Product Group 1’ or ‘Product Group 2’,
and press the ENT Key.
5)
Turn the large FMS Knob or press the ENT Key to scroll through product
selections.
6)
Turn the small FMS Knob to scroll through options for each product (ON/
OFF, range settings, etc.).
7)
Press the ENT Key to select an option.
8)
Press the FMS Knob or CLR Key to return to the Connext Weather Data
Link Page with the changed settings.
Additional
Features
Hazard
Avoidance
Procedures
Restoring Default Connext Weather Data Link Page Settings
1)
Select the Connext Weather Data Link Page.
2)
Press the MENU Key.
3)
With ‘Weather Setup’ highlighted, press the ENT Key.
4)
Press the MENU Key.
5)
Highlight the desired default(s) to restore (all or for selection) and press
ENT Key.
Appendix
Annun/
Alerts
Abnormal
Operation
Switching Between Connext and SiriusXM Weather Sources
1)
Turn the large FMS Knob on the MFD to select the MAP page group.
2)
Turn the small FMS Knob to select the desired Weather Data Link Page.
3)
4)
Press the MENU Key.
Turn the large FMS Knob to select ‘Display Connext Weather’, or ‘Display
XM Weather’ (choice dependent on current weather source) and press the
ENT Key.
Index
Viewing Legends for Displayed Connext Weather Products
50
1)
Select the Connext Weather Data Link Page.
2)
Press the LEGEND Softkey to display the legends for the displayed weather
products.
Garmin G1000 Cockpit Reference Guide for the Diamond DA42NG
190-00963-04 Rev. A
Hazard Avoidance
Flight
Instruments
Or:
a) Press the MENU Key.
b) Select ‘Weather Legend’ and press the ENT Key.
4)
To remove the Legend Window, press the LEGEND Softkey, the ENT or the
CLR Key, or press the FMS Knob.
AFCS
Setting Up and Customizing Weather Data for the Navigation Map
Page
Nav/Com/
XPDR/Audio
Turn the FMS Knob to scroll through the legends if more are available than
fit in the window.
EIS
3)
Select the Navigation Map Page.
2)
Press the MENU Key.
3)
With ‘Map Setup’ highlighted, press the ENT Key.
4)
Turn the small FMS Knob to select the ‘Weather’ Group and press the ENT
Key.
5)
Turn the large FMS Knob or press the ENT Key to scroll through product
selections.
6)
Turn the small FMS Knob to scroll through options for each product (ON/
OFF, range settings).
7)
Press the ENT Key to select an option.
8)
Press the FMS Knob or CLR Key to return to the Navigation Map Page with
the changed settings.
GPS Nav
1)
Flight
Planning
Procedures
Additional
Features
Abnormal
Operation
Annun/
Alerts
The Connext Data Request window provides the flight crew with the options to
define the requested weather coverage area(s), choose automatic weather update
intervals (if desired), and the ability to send or cancel weather data requests. The
window also displays the status of the Connext data request process.
Hazard
Avoidance
Connext Weather Data Requests
Requesting Connext Weather Data Manually
2)
Press the MENU Key.
3)
With ‘Connext Weather Request’ highlighted, press the ENT Key.
190-00963-04 Rev. A
Garmin G1000 Cockpit Reference Guide for the Diamond DA42NG
Index
Select the Connext Weather Data Link Page.
Appendix
1)
51
Hazard Avoidance
Flight
Instruments
4)
Turn the large FMS Knob to highlight the desired coverage option(s)
and press the ENT Key to check or uncheck one of more of the following
coverage selections:
EIS
• PRESENT POSITION – Requests data based on current location.
Nav/Com/
XPDR/Audio
• DESTINATION – Requests data based on active flight plan
destination (if the flight plan contains no destination, dashes ‘------” are
displayed.)
AFCS
• FPL – Requests data based on active flight plan. Turn the small
FMS Knob to select the desired flight plan look-ahead distance
option (or choose ‘REMAINING FPL’ to request the remainder of the
flight plan).
5)
Turn the large FMS Knob highlight to the ‘DIAMETER / RTE WIDTH’
distance field and turn the small FMS Knob to select the desired diameter
and route width of the request, then press the ENT Key.
6)
Turn the large FMS Knob until the ‘SEND REQ’ button is highlighted. Press
the ENT Key to initiate the request immediately or press the FMS Knob to
return to the Connext Data Link Page without requesting data.
During a Connext Data Request, the Request Status box initially displays
“Contacting Connext...”. Once a connection is established, the Request Status Box
displays “Receiving Wx Data... Time Remaining:” with an estimated data transfer time
(either minutes or seconds). If desired, the Connext Data Request window may be
closed while the data request is processing by pressing the FMS Knob; the data request
will continue to process in the background. Connext Data Requests typically take
between 1 to 4 minutes to complete depending on the size of the selected weather
coverage area and Iridium signal strength.
The system retrieves all available Worldwide Weather products within the selected
coverage area during an initial Connext Data Request, regardless of which products (if
any) are currently enabled for display. On subsequent requests, previously retrieved
textual data (such as METARs and TAFs) is retained if it has not expired, while new
textual weather data matching the current coverage area and all graphical weather data
is downloaded during every data request.
If the system cannot complete a Connext weather data request, one or more
messages will appear in the request status window as shown in the following table.
Index
Appendix
Annun/
Alerts
Abnormal
Operation
Additional
Features
Hazard
Avoidance
Procedures
Flight
Planning
GPS Nav
• WAYPOINT – Requests data based on any valid waypoint.
52
Garmin G1000 Cockpit Reference Guide for the Diamond DA42NG
190-00963-04 Rev. A
Hazard Avoidance
Description
Flight
Instruments
Weather Request
Status Message
EIS
Nav/Com/
XPDR/Audio
AFCS
GPS Nav
Flight
Planning
Procedures
Hazard
Avoidance
Additional
Features
Abnormal
Operation
Annun/
Alerts
Appendix
Auto requests inhibited The system has disabled automatic weather data requests
due to excessive errors. Automatic weather data requests
Send manual request
have stopped. Send a manual weather data request to
to reset.
resume automatic updates.
Auto update retry: ## The system will attempt another automatic weather data
Seconds
request after an error occurred during the previous request.
Timer counts down until the next automatic request occurs.
Connext Comm Error
A communications error has occurred with the GIA. The
[2]
system should be serviced.
Connext Comm Error
This occurs if multiple automatic weather data requests have
[4]
recently failed, or the GDL 59 or a GIA is off-line.
Connext Comm Error
The Iridium or Connext networks are not accessible. Check
[5]
Iridium signal strength. If this error persists, the system
should be serviced.
Connext Comm Error
A communications error has occurred. It this error persists,
[6]
the system should be serviced.
Connext Comm Error
A weather data transfer has timed out. Check Iridium signal
[7]
strength and re-send the data request.
Connext Comm Error
A server error has occurred or invalid data received.
[8]
Connext Login Invalid There is a problem with the Connext registration. Contact
Garmin Flight Data Services at 1-866-739-5687 in the United
States or (011) 913-440-1135 for assistance.
Connext Server
The Connext weather data server is temporarily out of
Temporarily Inop
service, but is expected to return to service in less than 30
minutes.
Connext Server Inop
The Connext weather data server will be out of service for at
least 30 minutes.
Index
190-00963-04 Rev. A
Garmin G1000 Cockpit Reference Guide for the Diamond DA42NG
53
Hazard Avoidance
Flight
Instruments
Weather Request
Status Message
Description
The weather data request coverage area does not contain
at least one of the following: a waypoint, a flight plan, or a
flight plan destination. Verify at least one of the coverage
options is enabled (checked) and contains required criteria,
then re-send the data request.
No Connext
The system is not be currently subscribed to Connext, or the
Subscription
access code is incorrect. Verify the access code. Contact
Garmin Flight Data Services at 1-866-739-5687 in the United
States or (011) 913-440-1135 for assistance.
Reduce Request Area
The Connext weather data request area exceeds size limits.
Reduce weather coverage area and re-send data request.
Request Cancelled
The user has cancelled a Connext weather data request.
Requested area too
The size of the Connext weather data request has exceeded
large. Reduce coverage limits. Reduce the size of the coverage area and try the
area.
weather data request again.
Request Failed - Try
The weather data request timed-out. Re-send data request.
Again
Transfer Preempted
The data link is busy. Retry request later.
Cancelling a Connext Weather Data Request in Progress
Annun/
Alerts
Abnormal
Operation
Additional
Features
Hazard
Avoidance
Procedures
Flight
Planning
GPS Nav
AFCS
Nav/Com/
XPDR/Audio
EIS
Invalid Coverage Area
1)
Select the Connext Weather Data Link Page.
2)
Press the MENU Key.
3)
With ‘Connext Data Request’ highlighted, press the ENT Key.
4)
Turn the large FMS Knob to select ‘CANCEL REQ’ and press the ENT Key.
The request status box indicates ‘Request Cancelled’.
5)
Press the FMS Knob to return to the Connext Weather Data Link Page.
Index
Appendix
Enabling Automatic Connext Data Requests
54
1)
Select the Connext Weather Data Link Page.
2)
Press the MENU Key.
3)
With ‘Connext Weather Request’ highlighted, press the ENT Key.
Garmin G1000 Cockpit Reference Guide for the Diamond DA42NG
190-00963-04 Rev. A
Hazard Avoidance
Turn the large FMS Knob to select the ‘UPDATE RATE’ setting. Then turn
the small FMS Knob to highlight the desired automatic update frequency
(OFF, 5 Min, 10 Min, 15 Min, 20 Min, 25 Min, 30 Min, 45 Min, or 60 Min),
then press the ENT Key.
6)
The ‘SEND REQ” button is highlighted and a countdown timer is displayed
in the ‘REQUEST STATUS’ based on the currently selected update rate.
Press the ENT Key to immediately send an immediate Connext Data
Request.
AFCS
Or:
Nav/Com/
XPDR/Audio
5)
EIS
Choose the desired weather coverage options.
Flight
Instruments
4)
Press the FMS Knob to return to the Connext Weather Data Link Page.
GPS Nav
Worldwide Weather Products
Press the MAP Softkey (for the PFD Inset Map, press the INSET Softkey).
This step is not necessary on the Connext Weather Data Link Page.
2)
Press the PRECIP Softkey.
Annun/
Alerts
Appendix
Radar data shown represents lowest level, base reflectivity, of radar returns. The
display of the information is color-coded to indicate the weather severity level. All
weather product legends can be viewed on the Connext Weather Data Link Page. For
the Precipitation legend, press the LEGEND Softkey when Precipitation is selected
for display.
Abnormal
Operation
1)
Additional
Features
Displaying Precipitation Weather Information
Hazard
Avoidance
NOTE: Precipitation data cannot be displayed on the Navigation Map Page
at the same time as terrain.
Procedures
Precipitation data is not real-time. The lapsed time between collection, processing,
and dissemination of radar images can be significant and may not reflect the current
radar synopsis. Due to the inherent delays and the relative age of the data, it should
be used for long-range planning purposes only.
Flight
Planning
Precipitation
Index
190-00963-04 Rev. A
Garmin G1000 Cockpit Reference Guide for the Diamond DA42NG
55
Hazard Avoidance
Flight
Instruments
Precipitation Limitations
Infrared Satellite
Infrared Satellite (IR SAT) data depicts cloud top temperatures from satellite
imagery. Brighter cloud top colors indicate cooler temperatures occurring at higher
altitudes.
Displaying Cloud Tops information
Index
Appendix
Annun/
Alerts
Abnormal
Operation
Additional
Features
Hazard
Avoidance
Procedures
Flight
Planning
GPS Nav
AFCS
Nav/Com/
XPDR/Audio
EIS
Radar images may have certain limitations:
• Radar base reflectivity does not provide sufficient information to determine cloud
layers or precipitation characteristics (wet hail vs. rain). For example, it is not
possible to distinguish between wet snow, wet hail, and rain.
• Radar base reflectivity is sampled at the minimum antenna elevation angle. An
individual radar site cannot depict high altitude storms at close ranges. It has
no information about storms directly over the site.
• When zoomed in to a range of 30 nm, each square block on the display represents
an area of four square kilometers.
The following may cause abnormalities in displayed radar images:
• Ground clutter
• Strobes and spurious radar data
• Sun strobes (when the radar antenna points directly at the sun)
• Interference from buildings or mountains, which may cause shadows
• Metallic dust from military aircraft, which can cause alterations in radar scans
1)
Select the Connext Weather Data Link Page.
2)
Press the IR SAT Softkey.
To display the Infrared Satellite legend, press the LEGEND Softkey when Infrared
Satellite data is selected for display.
Data Link Lightning
Lightning data shows the approximate location of cloud-to-ground lightning strikes.
A strike icon represents a strike that has occurred within a two-kilometer region.
Neither cloud-to-cloud nor the exact location of the lightning strike is displayed.
If the aircraft is also equipped with an on-board lightning detection system (e.g.,
L-3 WX-500 Stormscope®), only one lightning product may be enabled for display at
a time.
56
Garmin G1000 Cockpit Reference Guide for the Diamond DA42NG
190-00963-04 Rev. A
Hazard Avoidance
Press the MAP Softkey (for the PFD Inset Map, press the INSET Softkey).
This step is not necessary on the Connext Weather Data Link Page.
2)
Press the DL LTNG Softkey.
EIS
1)
Flight
Instruments
Displaying Data Link Lightning information
GPS Nav
Displaying SIGMETs and AIRMETs
AFCS
SIGMETs and AIRMETs
The entire SIGMET or AIRMET is displayed as long as any portion of it is occurring
within the coverage area of the Connext data request.
Nav/Com/
XPDR/Audio
To display the Data Link Lightning legend on the Weather Data Link Page, press the
LEGEND Softkey when Data Link Lightning is selected for display.
2)
Press the SIG/AIR Softkey.
3)
To view the text of the SIGMET or AIRMET, press the RANGE Knob and move
the Map Pointer over the icon.
4)
Press the ENT key.
METARs and TAFs
Hazard
Avoidance
To display the SIGMET and AIRMET legend, press the LEGEND Softkey when
SIGMETs and AIRMETs are selected for display.
Procedures
Select the Connext Weather Data Link Page.
Flight
Planning
1)
NOTE: METAR information is only displayed within the installed navigation
database service area.
Additional
Features
METAR and TAF text are displayed on the WPT-Weather Information Page. TAF
information is displayed in its raw form when it is available.
Abnormal
Operation
2)
Press the RANGE Knob and pan to the desired airport.
3)
Press the ENT Key. The Weather Information Page is shown with METAR
and TAF text.
4)
Use the FMS Knob or the ENT Key to scroll through the METAR and TAF
text. METAR text must be completely scrolled through before scrolling
through the TAF text.
190-00963-04 Rev. A
Garmin G1000 Cockpit Reference Guide for the Diamond DA42NG
Index
On the Connext Weather Data Link Page, press the METAR Softkey.
Appendix
1)
Annun/
Alerts
Displaying METAR and TAF text
57
Hazard Avoidance
Flight
Instruments
5)
Or:
EIS
1)
Flight
Planning
GPS Nav
AFCS
Nav/Com/
XPDR/Audio
b) Press the WX Softkey to select the Weather Information Page.
2)
Press the FMS Knob to display the cursor.
3)
Use the FMS Knob to enter the desired airport and press the ENT Key.
4)
Use the FMS Knob or the ENT Key to scroll through the METAR and TAF
text. Note that the METAR text must be completely scrolled through before
scrolling through the TAF text.
To display the METAR legend on the Connext Weather Data Link Page, press the
LEGEND Softkey when METARs are selected for display.
Winds Aloft
Winds Aloft data shows the forecasted wind speed and direction at the surface and
at selected altitudes. Altitude can be displayed in 3,000-foot increments up to 42,000
feet MSL.
Displaying Winds Aloft data
Additional
Features
Hazard
Avoidance
Procedures
Select the Weather Information Page.
a) Turn the large FMS Knob to select the Waypoint Page Group.
Abnormal
Operation
Annun/
Alerts
Appendix
Index
Press the FMS Knob or the CLR Key to return to the Connext Weather Data
Link Page.
1)
Select the Connext Weather Data Link Page.
2)
Press the MORE WX Softkey.
3)
Press the WIND Softkey.
4)
Press the desired altitude level: SFC (surface) up to 42,000 feet. Press the
NEXT or PREV Softkey to cycle through the altitude softkeys. The WIND
Softkey label changes to reflect the altitude selected.
To display the Winds Aloft legend, press the LEGEND Softkey when Winds Aloft
is selected for display.
PIREPs
Pilot Weather Reports (PIREPs) describe in-flight weather encountered by pilots.
A PIREP may contain unforecast adverse weather conditions, such as low in-flight
visibility, icing conditions, wind shear, turbulence, and type of aircraft flown. PIREPs
are issued as either Routine (UA) or Urgent (UUA).
58
Garmin G1000 Cockpit Reference Guide for the Diamond DA42NG
190-00963-04 Rev. A
Hazard Avoidance
3)
Press the PIREPS Softkey.
4)
Press the RANGE Knob and pan to the desired weather report. A gray
circle will appear around the weather report when it is selected.
5)
Press the ENT Key. The PIREP text is first displayed in a decoded fashion,
then as raw text.
6)
Use the FMS Knob or the ENT Key to scroll through the PIREP text.
7)
Press the FMS Knob or the CLR Key to close the PIREP text window and
return to the Connext Weather Data Link Page.
To display the PIREP or AIREP legend, press the LEGEND Softkey when PIREPs or
AIREPs are selected for display.
Flight
Planning
The PIREP color is determined by the type (routine or urgent).
WARNING: Do not use data link weather information for maneuvering
Index
59
Appendix
Garmin G1000 Cockpit Reference Guide for the Diamond DA42NG
Annun/
Alerts
The optional GDL 88 receives Flight Information Services - Broadcast (FIS-B)
weather data from a network of UAT ground-based transceivers (GBTs).
FIS-B weather data reception requires the aircraft being within range and line-ofsight of an operating GBT broadcasting FIS-B weather data. Reception may be affected
by factors including altitude or terrain.
Abnormal
Operation
determine the age of the weather information shown by the data link
weather product. Due to time delays inherent in gathering and processing
weather data for data link transmission, the weather information shown
by the data link weather product may be significantly older than the
indicated weather product age.
Additional
Features
WARNING: Do not use the indicated data link weather product age to
Hazard
Avoidance
in, near, or around areas of hazardous weather. Information contained
within data link weather products may not accurately depict current
weather conditions.
Procedures
FIS-B WEATHER
190-00963-04 Rev. A
GPS Nav
Press the MORE WX Softkey.
AFCS
2)
Nav/Com/
XPDR/Audio
Select the Connext Weather Data Link Page.
EIS
1)
Flight
Instruments
Displaying PIREP text
Reception of FIS-B weather data occurs automatically without any pilot action. FIS-B
broadcasts provide weather data in a repeating cycle which may take approximately
ten minutes to transmit all available weather data. Therefore, not all available weather
data may be available immediately upon initial FIS-B signal acquisition.
EIS
Flight
Instruments
Hazard Avoidance
Nav/Com/
XPDR/Audio
Turn the large FMS Knob to select the Map Page Group.
2)
Turn the small FMS Knob to select the Weather Data Link (FIS-B, XM, or
CNXT) Page.
AFCS
3)
If the page title displays a weather data link weather source other than
‘FIS-B’, such as ‘XM’ or ‘CNXT’, proceed to the following steps to change
the data link weather source.
4)
Press the MENU Key.
5)
Turn the small FMS Knob to select ‘Display FIS-B Weather’.
6)
Press the ENT Key. The page title will display ‘MAP - WEATHER DATA LINK
(FIS-B)’ to indicate FIS-B is now the selected data link weather source.
Flight
Planning
1)
GPS Nav
Viewing the Weather Data Link (FIS-B) Page
Index
Appendix
Annun/
Alerts
Abnormal
Operation
Additional
Features
Hazard
Avoidance
Procedures
Enabling/Disabling FIS-B Weather
1)
Select the Weather Data Link (FIS-B) Page.
2)
Press the MENU Key.
3)
Turn the small FMS Knob to highlight ‘Enable FIS-B Weather’ or ‘Disable
FIS-B Weather’, and press the ENT Key.
FIS-B Weather Product
NEXRAD Composite (US)
NEXRAD Composite
(Regional)
Meteorological Aerodrome
Report
(METARs)
Pilot Weather Report
(PIREPs)
60
Symbol
Expiration Time
(Minutes)
Broadcast Rate
(Minutes)
30
15
30
2.5
90
5
90
10
Garmin G1000 Cockpit Reference Guide for the Diamond DA42NG
190-00963-04 Rev. A
Hazard Avoidance
Broadcast Rate
(Minutes)
Winds Aloft
(WIND)
90
10
SIGMETs/AIRMETs
(SIG/AIR)
60
5
no product image
30
2.5
no product image
60
10
AFCS
no product image
Nav/Com/
XPDR/Audio
10
GPS Nav
Terminal Aerodrome
Forecast
Temporary Flight
Restriction (TFR)
EIS
No Radar Coverage
Symbol
Flight
Instruments
Expiration Time
(Minutes)
FIS-B Weather Product
Weather Product Symbols and Data Timing
Flight
Planning
Setting Up and Customizing the Weather Data Link (FIS-B) Page
Select the Weather Data Link (FIS-B) Page.
2)
Press the MENU Key.
3)
With ‘Weather Setup’ highlighted, press the ENT Key.
4)
Turn the small FMS Knob to select ‘Product Group 1’, and press the ENT
Key.
5)
Turn the large FMS Knob or press the ENT Key to scroll through product
selections.
6)
Turn the small FMS Knob to scroll through options for each product (ON/
OFF, range settings, etc.).
7)
Press the ENT Key to select an option.
8)
Press the FMS Knob or CLR Key to return to the Weather Data Link (FIS-B)
Page with the changed settings.
Procedures
1)
Hazard
Avoidance
Additional
Features
Abnormal
Operation
2)
Press the MENU Key.
3)
With ‘Map Setup’ highlighted, press the ENT Key.
190-00963-04 Rev. A
Garmin G1000 Cockpit Reference Guide for the Diamond DA42NG
Index
Select the Navigation Map Page.
Appendix
1)
Annun/
Alerts
Setting Up and Customizing FIS-B Weather on the Navigation Map
Page
61
AFCS
Nav/Com/
XPDR/Audio
EIS
Flight
Instruments
Hazard Avoidance
4)
Turn the small FMS Knob to select the ‘Weather’ Group and press the ENT
Key.
5)
Turn the large FMS Knob or press the ENT Key to scroll through product
selections.
6)
Turn the small FMS Knob to scroll through options for each product (ON/
OFF, range settings).
7)
Press the ENT Key to select an option.
8)
Press the FMS Knob or CLR Key to return to the Navigation Map Page with
the changed settings.
Procedures
Flight
Planning
GPS Nav
Displaying/Removing the Weather Product Information Box on the PFD
Inset Map
1)
On the PFD, press the INSET Softkey.
2)
Press the WX LGND Softkey.
3)
To remove the weather product information box, press the WX LGND
Softkey again.
1)
Select the Weather Data Link (FIS-B) Page.
2)
Press the LEGEND Softkey to display the legends for the displayed weather
products.
Additional
Features
Hazard
Avoidance
Viewing Legends for Displayed Weather Products on the Weather Data
Link (FIS-B) Page
Or:
a) Press the MENU Key.
Abnormal
Operation
b) Select ‘Weather Legend’ and press the ENT Key.
Annun/
Alerts
3)
To remove the Legend Window, press the LEGEND Softkey, the ENT or the
CLR Key, or press the FMS Knob.
Index
Appendix
Viewing Legends for Displayed Weather Products on the Navigation
Map Page
62
1)
Select the Navigation Map Page.
2)
Press the MAP Softkey.
3)
Press the LEGEND Softkey (available if one or more FIS-B weather products
are enabled for display).
Garmin G1000 Cockpit Reference Guide for the Diamond DA42NG
190-00963-04 Rev. A
Hazard Avoidance
To remove the Legend Window, press the LEGEND Softkey, the ENT or the
CLR Key, or press the FMS Knob.
Displaying NEXRAD Data
Press the MAP Softkey (for the PFD Inset Map, press the INSET Softkey).
This step is not necessary on the Weather Data Link (FIS-B) Page.
2)
Press the NEXRAD-C Softkey. This softkey becomes the US Softkey. A
mosaic of NEXRAD data for the continental United States (CONUS) is
displayed.
3)
To display the regional version of the NEXRAD weather product, press the
US Softkey. Softkey becomes the RGNL Softkey.
4)
To remove the NEXRAD weather product, press the RGNL Softkey. Softkey
becomes the NEXRAD-C Softkey.
EIS
1)
Nav/Com/
XPDR/Audio
AFCS
3)
To view the text of the SIGMET or AIRMET, press the Joystick and move
the Map Pointer over the icon.
4)
Press the ENT key.
Hazard
Avoidance
Press the SIG/AIR Softkey.
Procedures
2)
Flight
Planning
Select the Weather Data Link (FIS-B) Page.
Displaying METAR and TAF Text
3)
Press the ENT Key. The Weather Information Page is shown with METAR
and TAF text.
4)
Use the FMS Knob or the ENT Key to scroll through the METAR and TAF
text. METAR text must be completely scrolled through before scrolling
through the TAF text.
5)
Press the FMS Knob or the CLR Key to return to the Weather Data Link
(FIS-B) Page.
Appendix
Press the Joystick and pan to the desired airport.
Annun/
Alerts
2)
Abnormal
Operation
On the Weather Data Link (FIS-B) Page, press the METAR Softkey.
Additional
Features
1)
Or:
Select the Weather Information Page.
Index
1)
a) Turn the large FMS Knob to select the Waypoint Page Group.
b) Press the WX Softkey to select the Weather Information Page.
190-00963-04 Rev. A
Garmin G1000 Cockpit Reference Guide for the Diamond DA42NG
GPS Nav
Displaying SIGMETs and AIRMETs
1)
Flight
Instruments
4)
63
2)
Press the FMS Knob to display the cursor.
3)
Use the FMS Knob to enter the desired airport and press the ENT Key.
4)
Use the FMS Knob or the ENT Key to scroll through the METAR and TAF
text. Note that the METAR text must be completely scrolled through before
scrolling through the TAF text.
EIS
Flight
Instruments
Hazard Avoidance
GPS Nav
AFCS
Nav/Com/
XPDR/Audio
Displaying Raw METAR Text on the Active Flight Plan Page
1)
Select the Active Flight Plan Page on the MFD.
2)
Press the FMS Knob to activate the cursor.
3)
Turn the large FMS Knob to highlight the desired waypoint. The METAR
text will appear in the ‘SELECTED WAYPOINT WEATHER’ window below.
4)
When finished, press the FMS Knob to remove the cursor or press the FPL
Key to exit the Active Flight Plan Page.
1)
Select the Weather Data Link (FIS-B) Page.
2)
Press the MORE WX Softkey.
3)
Press the WIND OFF Softkey.
4)
Press the softkey for the desired altitude. Press the NEXT or PREV Softkey
to cycle through the altitude softkeys. The WIND Softkey label changes to
reflect the altitude selected.
Hazard
Avoidance
Procedures
Flight
Planning
Displaying Winds Aloft Information
Appendix
Annun/
Alerts
Abnormal
Operation
Additional
Features
Enabling/Disabling Predicted Temperatures with Winds Aloft Data
1)
Select the Weather Data Link (FIS-B) Page.
2)
Press the MENU Key.
3)
Turn the small FMS Knob to highlight ‘Weather Setup’ and press the ENT
Key.
4)
Turn the small FMS Knob to highlight ‘PRODUCT GROUP 1’ and press the
ENT Key.
5)
Turn the small FMS Knob to highlight the Temp (•) ‘ON’ or ‘OFF’ field, then
press the ENT Key.
6)
When finished, push the FMS Knob or the CLR Key.
Index
Displaying PIREP Text
64
1)
Select the Weather Data Link (FIS-B) Page.
2)
Press the MORE WX Softkey.
Garmin G1000 Cockpit Reference Guide for the Diamond DA42NG
190-00963-04 Rev. A
Hazard Avoidance
Press the Joystick and pan to the desired weather report. A gray circle will
appear around the weather report when it is selected.
5)
Press the ENT Key. The PIREP text is first displayed in a decoded fashion,
followed by the original text. Note the original text may contain additional
information not shown in the decoded version.
6)
Use the FMS Knob or the ENT Key to scroll through the PIREP text.
7)
Press the FMS Knob or the CLR Key to close the PIREP text window and
return to the Weather Data Link (FIS-B) Page.
AFCS
Displaying TFR Data
Press the Joystick and pan the map pointer over a TFR to highlight it. The
system displays TFR summary information above the map.
3)
Press the ENT Key. The system displays a pop-up menu.
4)
If necessary, turn the FMS Knob to select ‘Review Airspaces’ and press the
ENT Key. The system displays the INFORMATION window.
5)
Press the FMS Knob or the CLR Key to remove the INFORMATION window.
Hazard
Avoidance
Viewing FIS-B Weather Status
Procedures
2)
Flight
Planning
Select the Weather Data Link (XM) Page or Navigation Map Page.
GPS Nav
1)
1)
Nav/Com/
XPDR/Audio
4)
EIS
Press the PIREPS Softkey.
Flight
Instruments
3)
Turn the large FMS Knob to select the AUX Page Group.
Additional
Features
Abnormal
Operation
2) Turn the small FMS Knob to select the AUX - ADS-B Status Page.
ADS-B Status Page Item Status Message
Description
FIS-B Weather Status:
ENABLED
The FIS-B weather feature is enabled to
process and display FIS-B weather products.
FIS-B Processing
DISABLED
The FIS-B weather feature is disabled.
---------------No data received from the GDL 88 UAT.
Annun/
Alerts
Appendix
Index
190-00963-04 Rev. A
Garmin G1000 Cockpit Reference Guide for the Diamond DA42NG
65
ADS-B Status Page Item Status Message
Description
Weather Products:
AVAILABLE
FIS-B weather data is available for display
for the weather product.
AIRMET
CONUS NEXRAD
NOT AVAILABLE FIS-B weather data is not available for the
METAR
weather product, and/or the system is not
METAR GRAPHICAL
receiving the FIS-B weather service.
NOTAM/TFR
AWAITING DATA The system is receiving the FIS-B weather
service, and is waiting to receive the
PIREP
weather product from the FIS-B data
REGIONAL NEXRAD
broadcast.
SIGMET
TAF
WINDS/TEMPS ALOFT
AUX-ADS-B Status Page Messages for FIS-B Weather
Airborne Color Weather Radar
AIRBORNE COLOR WEATHER RADAR
Procedures
Flight
Planning
GPS Nav
AFCS
Nav/Com/
XPDR/Audio
EIS
Flight
Instruments
Hazard Avoidance
Hazard
Avoidance
WARNING: Begin transmitting only when it is safe to do so. If it is desired to
transmit while the aircraft is on the ground, no personnel or objects should
be within 11 feet of the antenna.
Abnormal
Operation
Additional
Features
CAUTION: In Standby Mode, the antenna is parked at the center line. It
is always a good idea to put the radar in Standby Mode before taxiing the
aircraft to prevent the antenna from bouncing on the bottom stop and possibly
causing damage to the radar assembly.
Index
Appendix
Annun/
Alerts
Displaying Weather on the Weather Radar Page
66
1)
Turn the large FMS Knob to select the Map Page Group.
2)
Turn the small FMS Knob to select the Weather Radar Page.
3)
Press the MODE Softkey.
4)
If the aircraft is on the ground, press the STANDBY Softkey. When a GWX
68 is installed, a one minute warm-up period is initiated. After the warmup is complete, the radar will enter the Standby Mode. When a GWX 70 is
installed, the radar will enter Standby Mode immediately. After the aircraft
is airborne, press the WEATHER Softkey.
Garmin G1000 Cockpit Reference Guide for the Diamond DA42NG
190-00963-04 Rev. A
Hazard Avoidance
Flight
Instruments
Or:
Turn the Joystick to select the desired range.
6)
If desired, press the VERTICAL Softkey for vertical scanning.
Hazard
Avoidance
*Magenta color not applicable to GWX 70 installations
Procedures
< 23 dBZ
23 dBZ to < 32 dBZ
23 dBZ to < 33 dBZ
32 dBZ to < 41 dBZ
33 dBZ to < 41 dBZ
41 dBZ to < 50 dBZ
41 dBz and greater
50 dBZ and greater
Flight
Planning
Black
Green (GWX 68)
Green (GWX 70)
Yellow (GWX 68)
Yellow (GWX 70)
Red (GWX 68)
Red (GWX 70)
Magenta* (GWX 68 only)
Approximate
Precipitation Rate (in/hr.)
< .01.
.01 - 0.1.
.01 - 0.1.
0.1 - 0.5
0.1 - 0.5
0.5 - 2
0.5 and greater
>2
GPS Nav
Intensity
AFCS
Weather Mode Color
Nav/Com/
XPDR/Audio
5)
EIS
If the aircraft is already airborne, press the WEATHER or GROUND
Softkey. When a GWX 68 is installed, a one-minute warm-up period will
be initiated, after which the radar will begin transmitting. When a GWX
70 is installed, there is no warm-up period and radar begins transmitting
immediately. The horizontal scan is initially displayed.
Additional
Features
Adjusting Antenna Tilt
Abnormal
Operation
Annun/
Alerts
Appendix
Move the Joystick up or down to adjust the tilt of the antenna up or down. Monitor the displayed tilt value in the TILT field.
When scanning vertically, a Tilt Line may be displayed to aid in positioning the tilt
of the antenna. If the Tilt Line is not displayed, perform the following steps:
1) Press the MENU Key
2) Turn the large FMS Knob to select ‘Show Tilt Line’.
3) Press the ENT Key.
Adjusting Antenna Bearing
190-00963-04 Rev. A
Garmin G1000 Cockpit Reference Guide for the Diamond DA42NG
67
Index
Move the Joystick right or left to adjust the azimuth position of the antenna right
or left. Monitor the displayed bearing value in the BEARING field.
When scanning horizontally, a Bearing Line may be displayed to aid in positioning
the antenna for the vertical scan. If the Bearing Line is not displayed, perform the following steps:
1) Press the MENU Key
2) Turn the large FMS Knob to select ‘Show Bearing Line’.
3) Press the ENT Key.
Vertically Scan a Storm Cell
1) While in the Horizontal Scan view, move the Joystick to place the Bearing
Line on the desired storm cell, or other area, to be vertically scanned.
Procedures
Flight
Planning
GPS Nav
AFCS
Nav/Com/
XPDR/Audio
EIS
Flight
Instruments
Hazard Avoidance
2)
Press the VERTICAL Softkey. A vertical ‘slice’ of the selected area will now
be displayed.
3)
Move the Joystick right or left to move the scanned “slice” a few degrees
right or left.
4)
Turn the Joystick to adjust the range.
5)
To select a new area to be vertically scanned, press the HORIZON Softkey
to return to the Horizontal Scan view and repeat the previous steps.
Hazard
Avoidance
Adjusting Gain
Appendix
Annun/
Alerts
Abnormal
Operation
Additional
Features
WARNING: Changing the gain in Weather Mode will cause precipitation
intensity to be displayed as a color not representative of the true intensity.
Remember to return the gain setting to ‘Calibrated’ for viewing the actual
intensity of precipitation.
1)
Press the GAIN Softkey to activate the cursor in the ‘GAIN’ field.
2)
Turn the small FMS Knob to adjust the gain for the desirable level. The
gain setting is visible in the gain field as a movable horizontal bar in
a flashing box. The line pointer is a reference depicting the calibrated
position.
3)
Press the FMS Knob to remove the cursor.
4)
Press the GAIN Softkey again to recalibrate the gain. ‘CALIBRATED’ will be
displayed in the ‘GAIN’ field.
Index
Ground Mapping
1)
68
Press the MODE Softkey.
Garmin G1000 Cockpit Reference Guide for the Diamond DA42NG
190-00963-04 Rev. A
Hazard Avoidance
Press the GROUND Softkey to place the radar in Ground Map Mode.
3)
Press the BACK Softkey.
4)
Press the FMS Knob to activate the cursor
5)
Press the FMS Knob to place the cursor in the ‘TITL’ field
6)
Adjust the antenna tilt angle by turning the small FMS Knob to position the
ground returns as desired.
7)
Press the FMS Knob to remove
Yellow (GWX 68)
Magenta (GWX 68)
Magenta (GWX 70)
Blue (GWX 70)
Hazard
Avoidance
Blue (GWX 68)
Procedures
Yellow (GWX 70
Flight
Planning
Cyan (GWX 70)
0 dB
0 dB to 3 dB
> 0 dB to < 9 dB
>3 dB to < 13 dB
9 dB to < 18 dB
13 dB to < 21 dB
18 dB to < 27 dB
21 dB < 29 dB
27 dB and greater
29 gB and greater
GPS Nav
Cyan (GWX 68)
AFCS
Black (GWX 70)
Intensity
Additional
Features
Sector Scan
2)
Press the FMS Knob to display the cursor.
3)
Turn the large FMS Knob to place the cursor in the SECTOR SCAN field.
4)
Turn the small FMS Knob to select FULL, 60˚, 40˚, or 20˚ scan.
5)
If desired, readjust the Bearing Line with the Joystick to change the center
of the Sector Scan.
6)
Press the FMS Knob to remove the cursor.
Appendix
Index
Garmin G1000 Cockpit Reference Guide for the Diamond DA42NG
Annun/
Alerts
While in the Horizontal Scan Mode, move the Joystick right or left to place
the Bearing Line in the desired position. The location of the Bearing Line
will become the center point of the Sector Scan.
Abnormal
Operation
1)
190-00963-04 Rev. A
Nav/Com/
XPDR/Audio
Black (GWX 68)
EIS
Ground Map Mode
Color
Flight
Instruments
2)
69
Hazard Avoidance
1)
To activate or deactivate the antenna stabilization, press the MODE
Softkey.
2)
Press the STAB ON Softkey to activate antenna stabilization or press the
STAB OFF Softkey to deactivate. The current stabilization condition is
shown in the upper right of the weather radar display.
Weather Attenuated Color Highlight (WATCH®)
To activate or deactivate the WATCH® feature, press the WATCH Softkey. This
feature is only available in the Horizontal Scan Mode.
Weather Alert
To activate or deactivate Weather Alert, press the WX ALRT Softkey. Activating and
deactivating will also enable or inhibit the alert on the PFD.
Automatic Standby
When the weather radar system is in the Weather or Ground Map Mode, upon
landing the system will automatically switch to Standby Mode.
TRAFFIC SYSTEMS
• If Traffic information Service (TIS) is configured, STANDBY, OPERATE, and
TNA MUTE softkeys are displayed.
• If a Traffic Advisory System (TAS) is configured, MUTE and ALT MODE softkeys
are displayed.
Additional
Features
Hazard
Avoidance
Procedures
Flight
Planning
GPS Nav
AFCS
Nav/Com/
XPDR/Audio
EIS
Flight
Instruments
Antenna Stabilization
Traffic Symbol
Description
Abnormal
Operation
Non-Threat Traffic
(intruder is beyond 5 nm and greater than 1200’ vertical separation)
Annun/
Alerts
Proximity Advisory (PA) (Not available with TIS system)
(intruder is within 5 nm and less than 1200’ vertical separation)
Appendix
Traffic Advisory (TA)
(closing rate, distance, and vertical separation meet TA criteria)
Index
Traffic Advisory Off Scale
Traffic Symbol Description
70
Garmin G1000 Cockpit Reference Guide for the Diamond DA42NG
190-00963-04 Rev. A
Hazard Avoidance
NOTE: If the G1000 is configured to use an optional Traffic Advisory System
(TAS), TIS is not available for use.
Flight
Instruments
Traffic Information Service (TIS)
EIS
Displaying Traffic on the Traffic Map Page
3)
Press the OPERATE Softkey to begin displaying traffic. ‘OPERATING’ is
displayed in the Traffic Mode field.
4)
Press the STANDBY Softkey to place the system in the Standby Mode.
‘STANDBY’ is displayed in the Traffic Mode field.
5)
Rotate the Joystick clockwise to display a larger area or rotate counterclockwise to display a smaller area.
6)
Press the TNA MUTE Softkey to mute the “Traffic Not Available” aural
alert.
Procedures
Turn the small FMS Knob to select the Traffic Map Page.
Flight
Planning
2)
GPS Nav
Turn the large FMS Knob to select the Map Page Group.
AFCS
1)
2)
Press the TRAFFIC Softkey. Traffic is now displayed on the map.
Additional
Features
Ensure TIS is operating. With the Navigation Map displayed, press the
MAP Softkey.
Hazard
Avoidance
Displaying Traffic on the Navigation Map
1)
Abnormal
Operation
Traffic Advisory System (TAS) (Optional)
Displaying Traffic on the Traffic Map Page
Turn the small FMS Knob to select the Traffic Map Page. ‘OPERATING’ is
displayed in the Traffic Mode field.
3)
Press the ALT MODE Softkey to change the altitude volume. Select the
desired altitude volume by pressing the BELOW, NORMAL, ABOVE, or
UNREST (unrestricted) Softkey. The selection is displayed in the Altitude
Mode field.
190-00963-04 Rev. A
Garmin G1000 Cockpit Reference Guide for the Diamond DA42NG
Index
2)
Appendix
Turn the large FMS Knob to select the Map Page Group.
Annun/
Alerts
1)
Nav/Com/
XPDR/Audio
NOTE: Traffic Information Service (TIS) is only available when the aircraft is
within the service volume of a TIS capable terminal radar site.
71
Flight
Instruments
Hazard Avoidance
EIS
Nav/Com/
XPDR/Audio
AFCS
Rotate the Joystick clockwise to display a larger area or rotate counterclockwise to display a smaller area.
5)
Press the MUTE Softkey to mute TAS voice alerts.
Displaying Traffic on the Navigation Map
1)
Ensure TAS is operating.
2)
With the Navigation Map displayed, press the MAP Softkey.
3)
Press the TRAFFIC Softkey. Traffic is now displayed on the map.
GDL 88 ADS-B TRAFFIC (OPTIONAL)
The optional Garmin GDL 88 is a dual-link Universal Access Transceiver (UAT).
It sends and receives Automatic Dependent Surveillance-Broadcast (ADS-B) traffic
information on the 978 MHz UAT frequency. The system provides visual annunciations
and voice traffic alerts to help the pilot visually acquire potentially conflicting traffic.
Flight
Planning
GPS Nav
4)
Procedures
Enabling/Disabling the Display of ADS-B Traffic
1) Select the Traffic Map Page.
2) Press the ADS-B Softkey.
Abnormal
Operation
Additional
Features
Hazard
Avoidance
Testing ADS-B Traffic
1) Select the Traffic Map Page.
2) If necessary, turn the Joystick to select a map range of 2 and 6 nm to
ensure full test pattern display.
2) Ensure the ADS-B Softkey is disabled.
3) If the optional TAS/TCAS I is installed, ensure the TAS STBY Softkey is
enabled.
4) Press the Test Softkey.
Annun/
Alerts
Enabling/Disabling the Display of Flight IDs
1) Select the Traffic Map Page.
Appendix
2)
Press the FLT ID Softkey to enable/disable the display of Flight IDs.
Index
Changing the Altitude Range
1) On the Traffic Map Page, select the ALT MODE Softkey.
2) Press one of the following Softkeys:
72
Garmin G1000 Cockpit Reference Guide for the Diamond DA42NG
190-00963-04 Rev. A
Hazard Avoidance
•
NORMAL: Displays non-threat and proximity traffic from 2700 feet
above the aircraft to 2700 feet below the aircraft. Typically used during
enroute phase of flight.
EIS
•
BELOW: Displays non-threat and proximity traffic from 2700 feet
above the aircraft to 9000 feet below the aircraft. Typically used during
descent phase of flight.
•
UNREST (unrestricted): All traffic is displayed from 9900 feet above
and 9900 feet below the aircraft.
AFCS
GPS Nav
To return to the Traffic Map Page, press the BACK Softkey.
Flight
Planning
Enabling/Disabling the Motion Vector Display
1) Select the Traffic Map Page.
2) Press the MOTION Softkey.
3) Press one of the following softkeys:
• ABS: Displays the motion vector pointing in the absolute direction.
• REL: Displays the motion vector relative to own aircraft
• OFF: Disables the display of the motion vector.
Procedures
Additional
Features
Abnormal
Operation
Annun/
Alerts
Appendix
Showing Additional Traffic Information
1) Select the Traffic Map Page.
2) Press the FMS Knob. A cyan bracket highlights the first selected traffic
symbol. Additional information appears in a window in the upper-right
corner of the Traffic Map Page.
3) To select a different aircraft symbol, turn the FMS Knob to move the cyan
bracket until the selected aircraft traffic symbol is highlighted.
Index
Garmin G1000 Cockpit Reference Guide for the Diamond DA42NG
Hazard
Avoidance
Adjusting the Duration for the Motion Vector Projected Time
1) Select the Traffic Map Page.
2) Press the MOTION Softkey.
3) Press the DURATION Softkey.
4) Press a softkey for the desired duration (30 SEC, 1 MIN, 2 MIN, 5 MIN).
5) When finished, press the BACK Softkey to return to the Traffic Map Page.
190-00963-04 Rev. A
Nav/Com/
XPDR/Audio
ABOVE: Displays non-threat and proximity traffic from 9000 feet above
the aircraft to 2700 feet below the aircraft. Typically used during climb
phase of flight.
Flight
Instruments
3)
•
73
Hazard Avoidance
Flight
Instruments
4)
AFCS
Nav/Com/
XPDR/Audio
EIS
Viewing ADS-B Traffic Status
1) Turn the large FMS Knob to select the AUX Page Group.
2) Turn the small FMS Knob to select the AUX - ADS-B Status Page.
ADS-B Status Page
Item
Traffic Application
Status: AIRBORNE
(AIRB), SURFACE
(SURF), AIRBORNE
ALERTS (CSA)
TIS-B/ADS-R Coverage
Status Message
Description
ON
Traffic application is currently on. Required
input data is available, and it meets
performance requirements.
AVAILABLE TO RUN Traffic application is not currently active, but
application is ready to run when condition(s)
determine the application should be active.
Required input data is available, and it meets
performance requirements.
NOT AVAILABLE Traffic application is not available. Required
input data is available, but it does not meet
performance requirements.
FAULT
Traffic application is not available. Required
input data is not available or the application
has failed.
NOT CONFIGURED Traffic application is not available, because it
has not been configured. If this annunciation
persists, the system should be serviced.
---------------Traffic application status is invalid or unknown.
AVAILABLE
The system is receiving the ADS-R coverage
from an FAA ground station.
NOT AVAILABLE The system is not receiving the ADS-R coverage
from an FAA ground station.
--------------ADS-R coverage is invalid or unknown.
Index
Appendix
Annun/
Alerts
Abnormal
Operation
Additional
Features
Hazard
Avoidance
Procedures
Flight
Planning
GPS Nav
When finished, press the FMS Knob again to remove the cyan selection
bracket.
74
Garmin G1000 Cockpit Reference Guide for the Diamond DA42NG
190-00963-04 Rev. A
Hazard Avoidance
Status Message
Flight
Instruments
ADS-B Status Page
Item
GPS Status: GPS
Source
Description
External #1
EIS
The GDL 88 is using the #1 GPS receiver for
the GPS position source.
External #2
The GDL 88 is using the #2 GPS receiver for
the GPS position source.
--------The GPS source is invalid or unknown.
Ground Uplink Status: Number of minutes, Displays the number of minutes since the
Last uplink
or ‘------’
last uplink from a ground station occurred. If
no uplink has been received, or the status is
invalid, dashes appear instead of a number of
minutes.
AUX-ADS-B Status Page Messages for ADS-B Traffic
Nav/Com/
XPDR/Audio
AFCS
GPS Nav
Flight
Planning
TERRAIN AND OBSTACLE PROXIMITY
Hazard
Avoidance
Displaying Terrain and Obstacles on the Terrain Proximity Page
2)
Turn the small FMS Knob to select the last rectangular page icon.
3)
If desired, press the VIEW Softkey to access the ARC and 360 Softkeys.
When the ARC Softkey is pressed, a radar-like 120° view is displayed. Press
the 360 Softkey to return to the 360° default display.
4)
Rotate the Joystick clockwise to display a larger area or rotate counterclockwise to display a smaller area.
Yellow
Terrain/Obstacle between 100’ and
1000’ below current aircraft altitude.
Gray
Terrain/Obstacle is more than 1000’
below aircraft altitude.
Garmin G1000 Cockpit Reference Guide for the Diamond DA42NG
Index
Terrain/Obstacle above or within 100’
below current aircraft altitude.
Appendix
Red
Annun/
Alerts
190-00963-04 Rev. A
Terrain/Obstacle Location
Abnormal
Operation
Turn the large FMS Knob to select the Map Page Group.
Additional
Features
1)
Color
Procedures
NOTE: Terrain data is not displayed when the aircraft latitude is greater than
75 degrees north or 60 degrees south.
75
Hazard Avoidance
1)
With the Navigation Map displayed, press the MAP Softkey.
2)
Press the TERRAIN Softkey. Terrain and obstacle proximity will now be
displayed on the map.
TERRAIN-SVS
NOTE: Terrain-SVS is only available when Synthetic Vision Technology (SVT)
option is installed.
AFCS
Nav/Com/
XPDR/Audio
EIS
Flight
Instruments
Displaying Terrain and Obstacles on the Navigation Map
GPS Nav
NOTE: Terrain data is not displayed when the aircraft latitude is greater than
75 degrees north or 60 degrees south.
Flight
Planning
Turn the large FMS Knob to select the Map Page Group.
2)
Turn the small FMS Knob to select the Terrain-SVS Page.
Procedures
3)
If desired, press the VIEW Softkey to access the ARC and 360 softkeys.
When the ARC Softkey is selected, a radar-like 120° view is displayed.
Press the 360 Softkey to return to the 360° default display.
4)
Rotate the Joystick clockwise to display a larger area or rotate counterclockwise to display a smaller area.
Annun/
Alerts
Abnormal
Operation
Additional
Features
1)
Hazard
Avoidance
Display Terrain on the Terrain-SVS Page
Color
Terrain/Obstacle Location
Red
Terrain/Obstacle above or within 100’
below current aircraft altitude.
Yellow
Terrain/Obstacle between 100’ and
1000’ below current aircraft altitude.
Gray
Terrain/Obstacle is more than 1000’
below aircraft altitude.
Index
Appendix
Enable/Disable Aviation Data
76
1)
While the Terrain-SVS Page is displayed, press the MENU Key.
2)
Turn the small FMS Knob to select “Show (or Hide) Aviation Data”.
3)
Press the ENT Key.
Garmin G1000 Cockpit Reference Guide for the Diamond DA42NG
190-00963-04 Rev. A
Hazard Avoidance
Flight
Instruments
Terrain-SVS Inhibit
EIS
Inhibit Terrain
While the Terrain-SVS Page is displayed, press the INHIBIT Softkey.
Or:
1) Press the MENU Key.
2) Turn the small FMS Knob to select ‘Inhibit Terrain’.
3) Press the ENT Key.
Nav/Com/
XPDR/Audio
AFCS
Enable Terrain
While the Terrain-SVS Page is displayed, press the INHIBIT Softkey.
Or:
1) While the Terrain-SVS Page is displayed, press the MENU Key.
2) Turn the small FMS Knob to select ‘Enable Terrain’.
3) Press the ENT Key.
GPS Nav
Flight
Planning
Procedures
Hazard
Avoidance
Additional
Features
Abnormal
Operation
Annun/
Alerts
Appendix
Index
190-00963-04 Rev. A
Garmin G1000 Cockpit Reference Guide for the Diamond DA42NG
77
Index
Appendix
Annun/
Alerts
Abnormal
Operation
Additional
Features
Hazard
Avoidance
Procedures
Flight
Planning
GPS Nav
AFCS
Nav/Com/
XPDR/Audio
EIS
Flight
Instruments
Hazard Avoidance
Blank Page
78
Garmin G1000 Cockpit Reference Guide for the Diamond DA42NG
190-00963-04 Rev. A
Additional Features
Flight
Instruments
ADDITIONAL FEATURES
SYNTHETIC VISION (OPTIONAL)
GPS Nav
Flight
Planning
Procedures
Hazard
Avoidance
Additional
Features
Pathways
Flight Path Marker
Horizon Heading Marks
Terrain and Obstacle Alerting
Three-dimensional Traffic
Airport Signs
Runway Display
Abnormal
Operation
Annun/
Alerts
•
•
•
•
•
•
•
AFCS
Synthetic Vision Technology (SVT) functionality is offered as an optional
enhancement to the G1000 Integrated Flight Deck System.
SVT is primarily comprised of a computer-generated forward-looking, attitude
aligned view of the topography immediately in front of the aircraft from the pilot’s
perspective. SVT information is shown on the primary flight display (PFD).
SVT offers a three-dimensional view of terrain and obstacles. Terrain and
obstacles that pose a threat to the aircraft in flight are shaded yellow or red.
In addition to SVT enhancement to the PFD, the following feature enhancements
have been added to the PFD:
Nav/Com/
XPDR/Audio
WARNING: Do not use SVT runway depiction as the sole means for
determining the proximity of the aircraft to the runway or for maintaining
the proper approach path angle during landing.
EIS
WARNING: Use appropriate primary systems for navigation, and for terrain,
obstacle, and traffic avoidance. SVT is intended as an aid to situational
awareness only and may not provide the accuracy and/or fidelity upon which
to solely base decisions and/or plan maneuvers to avoid terrain, obstacles, or
traffic.
Displaying SVT Terrain
2)
Press the SYN VIS Softkey.
3)
Press the SYN TERR Softkey.
4)
Press the BACK Softkey to return to the previous page.
190-00963-04 Rev. A
Garmin G1000 Cockpit Reference Guide for the Diamond DA42NG
Index
Press the PFD Softkey.
Appendix
1)
79
Additional Features
Nav/Com/
XPDR/Audio
EIS
Flight
Instruments
Displaying Pathways
2)
Press the SYN VIS Softkey.
3)
If not already enabled, press the SYN TERR Softkey.
4)
Press the PATHWAY Softkey.
5)
Press the BACK Softkey to return to the previous page.
AFCS
GPS Nav
Flight
Planning
1)
Press the PFD Softkey.
2)
Press the SYN VIS Softkey.
3)
If not already enabled, press the SYN TERR Softkey.
4)
Press the HRZN HDG Softkey.
5)
Press the BACK Softkey to return to the previous page.
Procedures
Displaying Airport Signs
Hazard
Avoidance
Additional
Features
Press the PFD Softkey.
Displaying Heading on the Horizon
1)
Press the PFD Softkey.
2)
Press the SYN VIS Softkey.
3)
If not already enabled, press the SYN TERR Softkey.
4)
Press the APTSIGNS Softkey.
5)
Press the BACK Softkey to return to the previous page.
TERMINAL PROCEDURE CHARTS
NOTE: Regardless of the availability of SafeTaxi®, ChartView, or FliteCharts®,
it may be necessary to carry another source of charts on-board the aircraft.
Abnormal
Operation
Annun/
Alerts
Appendix
Index
1)
SafeTaxi®
SafeTaxi® is an optional feature that gives greater map detail as the map range
is adjusted in on the airport. The airport display on the map reveals runways with
numbers, taxiways identifiers, and airport landmarks including ramps, buildings,
control towers, and other prominent features. Resolution is greater at lower map
ranges. The aircraft symbol provides situational awareness while taxiing.
Pressing the DCLTR Softkey (declutter) once removes the taxiway markings and
airport identification labels. Pressing the DCLTR Softkey twice removes VOR station
ID, the VOR symbol, and intersection names if within the airport plan view. Pressing
80
Garmin G1000 Cockpit Reference Guide for the Diamond DA42NG
190-00963-04 Rev. A
Additional Features
Flight
Instruments
EIS
Nav/Com/
XPDR/Audio
the DCLTR Softkey a third time removes the airport runway layout, unless the airport
in view is part of an active route structure. Pressing the DCLTR Softkey again cycles
back to the original map detail.
The SafeTaxi database contains detailed airport diagrams for selected airports.
These diagrams provide the pilot with situational awareness by displaying the aircraft
position in relation to taxiways, ramps, runways, terminals, and services. This
information should not be used by the pilot as the basis for maneuvering the aircraft
on the ground. This database is updated on a 56-day cycle.
ChartView (Optional)
Hazard
Avoidance
Additional
Features
Abnormal
Operation
1)
Procedures
View Charts from the Navigation Map Page
Flight
Planning
FliteCharts® resemble the paper version of AeroNav Services terminal procedures
charts. The charts are displayed with high-resolution and in color for applicable
charts. The selected Display Pane depiction shows the aircraft position on the moving
map in the plan view of most approach charts and on airport diagrams.
The FliteCharts database contains procedure charts for the United States only.
This database is updated on a 28-day cycle. If not updated within 180 days of the
expiration date, FliteCharts will no longer function.
GPS Nav
FliteCharts® (Optional)
AFCS
ChartView resembles the paper version of Jeppesen terminal procedures charts.
The charts are displayed in full color with high-resolution. The MFD depiction shows
the aircraft position on the moving map in the plan view of most approach charts and
on airport diagrams.
The ChartView database is updated on a 14-day cycle. If the ChartView database is
not updated within 70 days of the expiration date, ChartView will no longer function.
Press the SHW CHRT Softkey when displayed.
Or:
3)
Press the GO BACK Softkey to return to the previous page.
190-00963-04 Rev. A
Garmin G1000 Cockpit Reference Guide for the Diamond DA42NG
Index
Press the DP, STAR, APR, WX, and NOTAM softkeys to access charts for
departures, arrivals, approaches, weather and NOTAMs Note that NOTAMS
are only available with ChartView.
Appendix
2)
Annun/
Alerts
Move the map pointer to point to a desired point on the map and press the
SHW CHRT Softkey.
81
Additional Features
Nav/Com/
XPDR/Audio
EIS
Flight
Instruments
View Charts from the Active Flight Plan Page
AFCS
GPS Nav
Flight
Planning
Procedures
Hazard
Avoidance
Additional
Features
Abnormal
Operation
Annun/
Alerts
While viewing the Active Flight Plan Page, press the FMS Knob to activate
the cursor.
2)
Turn the large FMS Knob to select the departure airport, destination
airport, departure, arrival, or approach.
3)
Press the SHW CHRT Softkey. The appropriate chart is displayed, if
available for the item selected.
4)
Press the GO BACK Softkey to return to the previous page.
Change Day/Night View
1)
While viewing a chart press the MENU Key to display the Page Menu
OPTIONS.
2)
Turn the large FMS Knob to highlight the ‘Chart Setup’ Menu Option and
press the ENT Key.
3)
Turn the large FMS Knob to move between the ‘FULL SCREEN’ and ‘COLOR
SCHEME’ Options.
4)
Turn the small FMS Knob to choose between the ‘On’ and ‘Off’ Full Screen
Options.
5)
Turn the small FMS Knob to choose between ‘Day’, ‘Auto’, and ‘Night’
Options.
6)
In Auto Mode, turn the large FMS Knob to select the percentage field and
change percentage with the small FMS Knob. The percentage of change is
the day/night crossover point based on backlighting intensity.
7)
Press the FMS Knob when finished to remove the Chart Setup Menu.
AIRPORT DIRECTORY
The AOPA or optional AC-U-KWIK® Airport Directory adds enhanced airport
information when viewing airports on the WPT-Airport Information Page.
The Airport Directory databases are revised every 56 days and is available
through subscription. Check fly.garmin.com for the current database.
View Airport Directory Information
While viewing the WPT-Airport Information Page, if necessary, press the
INFO-1 Softkey to change the softkey label to display INFO-2. Airport
Directory information is displayed on the right half of the display.
Index
Appendix
1)
82
Garmin G1000 Cockpit Reference Guide for the Diamond DA42NG
190-00963-04 Rev. A
Additional Features
The XM® Radio Page provides information and control of the audio entertainment
features of the SiriusXM Satellite Radio.
2)
Turn the small FMS Knob to select the displayed AUX - XM Information
Page.
3)
Press the RADIO Softkey to show the XM Radio Page where audio
entertainment is controlled.
AFCS
Turn the large FMS Knob to select the Auxiliary Page Group.
Nav/Com/
XPDR/Audio
1)
EIS
Selecting the XM Radio Page
Selecting a Category
Annun/
Alerts
Press the CH + Softkey to go up through the list in the Channel Box, or
move down the list with the CH – Softkey.
Appendix
Or:
Press the FMS Knob to highlight the channel list and turn the large FMS
Knob to scroll through the channels.
2)
Press the ENT Key to activate the selected channel.
190-00963-04 Rev. A
Garmin G1000 Cockpit Reference Guide for the Diamond DA42NG
Index
1)
Abnormal
Operation
2)
Additional
Features
While on the XM Radio Page, press the CHNL Softkey.
Hazard
Avoidance
Select an Available Channel within the Selected Category
Procedures
The Category Box of the XM Radio Page displays the currently selected category
of audio.
1) Press the CATGRY Softkey on the XM Radio Page.
2) Press the CAT + and CAT - Softkeys to cycle through the categories.
Or:
Turn the small FMS Knob to display the Categories list. Highlight the
desired category with the small FMS Knob and press the ENT Key. Selecting
All Categories places all channels in the list.
Flight
Planning
The Active Channel Box on the XM Radio Page displays the currently selected
channel. The Channels List Box of the XM Radio Page shows a list of the available
channels for the selected category.
GPS Nav
Active Channel and Channel List
1)
Flight
Instruments
SIRIUSXM SATELLITE RADIO ENTERTAINMENT (OPTIONAL)
83
Additional Features
1)
While on the XM Radio Page, press the CHNL Softkey.
2)
Press the DIR CH Softkey. The channel number in the Active Channel Box
is highlighted.
3)
Press the numbered softkeys located on the bottom of the display to
directly select the desired channel number.
4)
Press the ENT Key to activate the selected channel.
Nav/Com/
XPDR/Audio
EIS
Flight
Instruments
Entering a Channel Directly
AFCS
Assigning Channel Presets
Hazard
Avoidance
Procedures
Flight
Planning
GPS Nav
Up to 15 channels from any category can be assigned a preset number.
1) On the XM Radio Page, while listening to an Active Channel that is wanted
for a preset, press the PRESETS Softkey to access the first five preset
channels (PS1 - PS5).
2) Press the MORE Softkey to access the next five channels (PS6 – PS10),
and again to access the last five channels (PS11 – PS15). Pressing the
MORE Softkey repeatedly cycles through the preset channels.
3) Press any one of the (PS1 - PS15) softkeys to assign a number to the
active channel.
4) Press the SET Softkey on the desired channel number to save the channel
as a preset.
1)
With the XM Radio Page displayed, press the VOL Softkey.
2)
Press the VOL – Softkey to reduce volume or press the VOL + Softkey to
increase volume. (Once the VOL Softkey is pressed, the volume can also be
adjusted using the small FMS Knob.)
SATELLITE TELEPHONE & SMS MESSAGING SERVICE (OPTIONAL)
Operation of these features in the cockpit is accomplished through the AUXTELEPHONE, and the AUX-TEXT MESSAGING SETUP Pages.
NOTE: Aural and pop-up visual annunciations for incoming calls and received
text messages are inhibited during taxiing, takeoff and landing roll, low
altitude operations, low airspeed operations, and excessive pitch and roll
attitudes.
Index
Appendix
Annun/
Alerts
Abnormal
Operation
Additional
Features
Adjusting Volume
84
Garmin G1000 Cockpit Reference Guide for the Diamond DA42NG
190-00963-04 Rev. A
Additional Features
Nav/Com/
XPDR/Audio
Disable/Enable Iridium Transceiver
Iridium telephone may be turned on or off by performing the following steps.
AFCS
To enable the Iridium telephone system:
With the AUX-TELEPHONE Page displayed, select the MENU Key on the
MFD to display the Page Menu.
2)
Turn either FMS Knob to place the cursor on ‘Enable Iridium Transmission’.
3)
Press the ENT Key.
Flight
Planning
To disable the Iridium telephone system:
2)
Turn either FMS Knob to place the cursor on ‘Disable Iridium Transmission’.
3)
Press the ENT Key.
Hazard
Avoidance
With the AUX-TELEPHONE Page displayed, select the MENU Key on the
MFD to display the Page Menu.
Telephone Communication
Abnormal
Operation
To view the Telephone Page:
Annun/
Alerts
Turn the small FMS Knob to select AUX - TELEPHONE
Additional
Features
The pilot or copilot can place and answer calls on the Iridium satellite network.
Control and monitoring of telephone functions are accomplished through the AUXTELEPHONE Page.
2)
Procedures
1)
Turn the large FMS Knob on the MFD to select the AUX page group.
GPS Nav
1)
1)
EIS
A subscriber account must be established prior to using the Iridium Satellite
System. Before setting up an Iridium account, obtain the serial number of the Iridium
Transceiver and the System ID by viewing the AUX- SYSTEM STATUS Page. Contact
Garmin Connext at 1-866-739-5687 in the United States or 913-397-8200, ext. 1135.
Flight
Instruments
Registering With Garmin Connext
Appendix
Index
190-00963-04 Rev. A
Garmin G1000 Cockpit Reference Guide for the Diamond DA42NG
85
Additional Features
Flight
Instruments
Internal
Phone
External
Phone
Description
EIS
Phone is Idle
Nav/Com/
XPDR/Audio
Phone is ringing
AFCS
Phone has a dial tone (off hook) or connected to
another phone
GPS Nav
Phone dialed is busy
Flight
Planning
Phone is dialing another phone
Procedures
Phone has failed
Hazard
Avoidance
Phone status not known
Abnormal
Operation
Additional
Features
Phone is disabled
Annun/
Alerts
Phone is reserved for data transmission
Appendix
Calling other phone or incoming call from other phone
Index
Other phone is on hold
Phones are connected
86
Garmin G1000 Cockpit Reference Guide for the Diamond DA42NG
190-00963-04 Rev. A
Additional Features
EIS
Nav/Com/
XPDR/Audio
AFCS
NOTE: The Push-to-Talk switch is not utilized for telephone communication.
The microphone is active after selecting the ANSWER Softkey, and stays active
until the call is terminated.
Flight
Instruments
Incoming Calls
When viewing MFD pages other than the AUX-TELEPHONE Page, a pop-up alert
will be displayed. The pop-up alert may be inhibited at times, such as during takeoff.
In addition to the pop-up alert, a ringing phone symbol will be displayed to the right
of the MFD page title. Also, the voice alert “Incoming Call” will be heard on the
selected cockpit audio.
Answering an incoming call:
Press the TEL Key on the audio panel.
2)
Select the ANSWER Softkey on the MFD.
GPS Nav
1)
Flight
Planning
Or:
While viewing the AUX-TELEPHONE Page:
2)
Press the MENU Key to display the Page Menu.
3)
Turn either FMS Knob to place the cursor on ‘Answer Incoming Call’.
4)
Press the ENT Key.
Hazard
Avoidance
Press the TEL Key on the audio panel.
Procedures
1)
Annun/
Alerts
2)
Turn either FMS Knob to place the cursor on ‘Disable Incoming Call Alerts’.
3)
Press the ENT Key. The voice and pop-up alert will not be displayed now
when an incoming call is received.
Garmin G1000 Cockpit Reference Guide for the Diamond DA42NG
Index
With the AUX-TELEPHONE Page displayed, press the MENU Key on the
MFD to display the Page Menu.
Appendix
1)
190-00963-04 Rev. A
Abnormal
Operation
Disabling incoming call alerts:
Additional
Features
Selecting the IGNORE Softkey will extinguish the pop-up window and leave the
current call unanswered. Selecting the IGNRE ALL Softkey will extinguish the popup window for the current and all future incoming calls and leave the current call
unanswered. Selecting the TEL Softkey will display the AUX-TELEPHONE Page
allowing additional call information to be viewed before answering.
87
Additional Features
Flight
Instruments
Outgoing Calls
Voice calls can be made from the cockpit through the Iridium Satellite Network.
1)
Press the TEL Key on the appropriate audio panel.
2)
Select the DIAL Softkey on the MFD.
3)
Turn the small FMS Knob to select ‘IRIDIUM’.
4)
Press the ENT Key. The cursor has now moved to the phone number entry field.
5)
Enter the desired telephone number by selecting the number softkeys on
the MFD or by pressing the numeric keys on the MFD Control Unit. The
International dialing sequence is necessary to place a call from the cockpit
to an external phone: Country Code + City/Area Code (if any) + Telephone
Number.
GPS Nav
AFCS
Nav/Com/
XPDR/Audio
EIS
To make a call:
Flight
Planning
The following country codes may be used when calling other satellite
telephone systems.
Abnormal
Operation
Additional
Features
Hazard
Avoidance
Procedures
Satellite System
Inmarsat
ICO
Ellipso
Iridium
Globalstar
6)
Press the ENT Key. ‘OK’ is highlighted.
7)
Press the ENT Key. The system will begin calling the number.
To exit the call, press the HANGUP Softkey.
Annun/
Alerts
Text Messaging (SMS)
Messages may be sent to an email address or text message capable cellular telephone.
Message length is limited to 160 characters, including the email address.
The text messaging user interface is mainly through the AUX-TEXT MESSAGING
Page.
Index
Appendix
Country Code
870
8810 or 8811
8812 or 8813
8816 or 8817
8818 or 8819
88
Garmin G1000 Cockpit Reference Guide for the Diamond DA42NG
190-00963-04 Rev. A
Additional Features
2)
Turn the small FMS Knob to select the AUX - TELEPHONE.
3)
If necessary, press the SMS Softkey to display the AUX-TEXT MESSAGING
Page
Message Symbol
Description
Nav/Com/
XPDR/Audio
Turn the large FMS Knob on the MFD to select the AUX page group.
EIS
1)
Flight
Instruments
Viewing the Text Messaging Page
Received text message that has not been opened
AFCS
Received text message that has been opened
GPS Nav
Saved text message, draft not sent
Flight
Planning
System is sending text message
Procedures
Text message has been sent
Hazard
Avoidance
System failed to send text message
Additional
Features
Predefined text message
Index
89
Appendix
Garmin G1000 Cockpit Reference Guide for the Diamond DA42NG
Annun/
Alerts
190-00963-04 Rev. A
Abnormal
Operation
Viewing a Text Message When Received
When viewing MFD pages other than the AUX-TEXT MESSAGING Page, a pop-up
alert will be displayed when a new text message is received.
Press the VIEW Softkey to view the message. Pressing the IGNORE Softkey will
extinguish the pop-up window and leave the text message unopened. Pressing the
IGNR ALL Softkey will extinguish the pop-window and ignore all future incoming
text messages. Pressing the SMS Softkey will display the AUX-TEXT MESSAGING
Page.
The pop-up alerts may be enabled or disabled through the Page Menu.
Additional Features
Nav/Com/
XPDR/Audio
EIS
Flight
Instruments
Enable/Disable Incoming Text Message Pop-Up Alerts
1)
With the AUX-TEXT MESSAGING Page displayed, press the MENU Key on
the MFD to display the Page Menu.
2)
Turn either FMS Knob to place the cursor on ‘Disable New Message
Popups’ or ‘Enable New Message Popups’.
3)
Press the ENT Key. The pop-up alert will not be displayed when an
incoming text message is received.
AFCS
Reply to a Text Message
While viewing the text message, press the REPLY Softkey.
GPS Nav
Or:
a) Press the MENU Key to display the Page Menu.
b) Turn either FMS Knob to place the cursor on ‘Reply To Message’.
Flight
Planning
c) Press the ENT Key.
Procedures
Sending a Text Message
1)
While viewing the AUX-TEXT MESSAGING Page, press the NEW Softkey.
Or:
Hazard
Avoidance
a) Press the MENU Key to display the Page Menu.
b) Turn either FMS Knob to place the cursor on ‘Draft New Message’.
2)
The TEXT MESSAGE DRAFT Window is now displayed with the cursor in the
‘TO’ field. Enter the desired telephone number or email address. Entry can
be accomplished through the alphanumeric keys on the PFD/MFD Control
Unit, or combination of the FMS Knob on the controller and softkeys on
the MFD. The FMS Knob is used to enter letters and numbers, or numbers
can be entered from the MFD by pressing the NUMBERS Softkey. Press
the CAP LOCK Softkey to create upper and lower case alpha characters.
Special characters can be accessed by pressing the SYMBOLS Softkey.
3)
Press the ENT Key. The cursor is now displayed in the ‘MESSAGE’ field.
4)
Enter the desired message using any combination of entry methods as
described in step 2.
Index
Appendix
Annun/
Alerts
Abnormal
Operation
Additional
Features
c) Press the ENT Key.
90
Garmin G1000 Cockpit Reference Guide for the Diamond DA42NG
190-00963-04 Rev. A
Additional Features
Press the ENT Key.
6)
Press the SEND Softkey to send the message immediately, or press the
SAVE Softkey to save the message in Outbox for sending at a later time.
Press the CANCEL Softkey to delete the message.
Flight
Instruments
5)
Turn either FMS Knob to select ‘Edit Predefined Messages’.
3)
Press the ENT Key. The PREDEFINED MESSAGES view is now displayed.
4)
Press the NEW Softkey.
Flight
Planning
2)
GPS Nav
While viewing the AUX-TEXT MESSAGING Page, press the MENU Key to
display the Page Menu.
AFCS
1)
Or:
a) Press the MENU Key to display the Page Menu.
Procedures
b) Turn either FMS Knob to place the cursor on ‘Draft New Predefined
Message’.
Press the ENT Key. The cursor is now displayed in the ‘MESSAGE’ field.
7)
Enter the desired message using any combination of entry methods as
described in step 5.
8)
Press the ENT Key.
9)
Press the SAVE Softkey. The new predefined message is now shown in
the displayed list. Pressing the CANCEL Softkey will delete the message
without saving.
Appendix
Index
Garmin G1000 Cockpit Reference Guide for the Diamond DA42NG
Annun/
Alerts
6)
Abnormal
Operation
The cursor is displayed in the ‘TITLE’ field. Enter the desired message title.
Entry can be accomplished through the alphanumeric keys on the PFD/MFD
Control Unit, or combination of the FMS Knob on the controller and softkeys
on the MFD. The FMS Knob is used to enter letters and numbers, or numbers
can be entered from the MFD by pressing the NUMBERS Softkey. Press the
CAP LOCK Softkey to create upper and lower case alpha characters. Special
characters can be accessed by pressing the SYMBOLS Softkey.
Additional
Features
5)
Hazard
Avoidance
c) Press the ENT Key. The PREDEFINED SMS TEXT MESSAGE Window is
now displayed.
190-00963-04 Rev. A
Nav/Com/
XPDR/Audio
Create a Predefined Text Message
EIS
Predefined Text Messages
Time and effort can be saved in typing text messages that are used repeatedly by
saving these messages as a predefined message.
91
Additional Features
Flight
Instruments
10) Press the MENU Key to display the Page Menu.
11) Turn either FMS Knob to place the cursor on ‘Stop Editing Predefined
Message’.
EIS
12) Press the ENT Key.
1)
While viewing the AUX-TEXT MESSAGING Page, press the NEW Softkey.
2)
The TEXT MESSAGE DRAFT Window is now displayed with the cursor in the
‘TO’ field. Enter the desired telephone number or email address. Entry can
be accomplished through the alphanumeric keys on the PFD/MFD Control
Unit, or combination of the FMS Knob on the controller and softkeys on
the MFD. The FMS Knob is used to enter letters and numbers, or numbers
can be entered from the MFD by pressing the NUMBERS Softkey. Press
the CAP LOCK Softkey to create upper and lower case alpha characters.
Special characters can be accessed by pressing the SYMBOLS Softkey.
3)
Press the ENT Key. The cursor is now displayed in the ‘MESSAGE’ field.
4)
Press the PREDEFD Softkey. The PREDEFINED MESSAGE MENU Window is
displayed.
6)
Press the ENT Key. The predefined message text is inserted into the
message field. If desired, the message can be edited by using the FMS
Knobs.
7)
Press the ENT Key.
8)
Press the SEND Softkey to transmit the message.
Text Message Boxes
Received text messages reside in the Inbox as ‘Read’ or ‘Unread’ messages. The
Outbox contains ‘Sent’ and ‘Unsent’ text messages. Saved messages that are meant to
be sent later are stored as Drafts. Each text message box may be viewed separately, or
together in any combination.
Show Inbox Messages
Appendix
Annun/
Alerts
Abnormal
Operation
Additional
Features
Hazard
Avoidance
Procedures
Flight
Planning
GPS Nav
AFCS
Nav/Com/
XPDR/Audio
Send a Predefined Text Message
While viewing the AUX-TEXT MESSAGING Page, press the ARRANGE
Softkey, then press the INBOX Softkey.
Index
Or:
92
Garmin G1000 Cockpit Reference Guide for the Diamond DA42NG
190-00963-04 Rev. A
Additional Features
Flight
Instruments
a) Press the MENU Key to display the Page Menu.
b) Turn either FMS Knob to place the cursor on ‘Show Inbox Messages’.
EIS
c) Press the ENT Key. The message box selected for viewing is indicated
at the bottom left of the list window.
Show Outbox Messages
Nav/Com/
XPDR/Audio
While viewing the AUX-TEXT MESSAGING Page, press the ARRANGE
Softkey, then press the OUTBOX Softkey.
Or:
AFCS
a) Press the MENU Key to display the Page Menu.
b) Turn either FMS Knob to place the cursor on ‘Show Outbox Messages’.
GPS Nav
c) Press the ENT Key. The message box selected for viewing is indicated
at the bottom left of the list window.
Flight
Planning
Show Draft Messages
While viewing the AUX-TEXT MESSAGING Page, press the ARRANGE
Softkey, then press the DRAFTS Softkey.
Procedures
Or:
a) Press the MENU Key to display the Page Menu.
Hazard
Avoidance
b) Turn either FMS Knob to place the cursor on ‘Show Draft Messages’.
c) Press the ENT Key. The message box selected for viewing is indicated
at the bottom left of the list window.
Annun/
Alerts
While viewing the AUX-TEXT MESSAGING Page, press the ARRANGE
Softkey, then press the TIME Softkey.
Appendix
Or:
a) Press the MENU Key to display the Page Menu.
Index
b) Turn either FMS Knob to place the cursor on ‘Sort By Date/Time’.
c) Press the ENT Key. The sorting selection is indicated at the bottom
center of the list window.
190-00963-04 Rev. A
Garmin G1000 Cockpit Reference Guide for the Diamond DA42NG
Abnormal
Operation
View Messages Sorted by Message Date/Time:
Additional
Features
Arranging Text Messages
The viewed messages may be listed according to the date/time the message was
sent or received, the type of message (read, unread, sent, unsent, etc.), or by message
address.
93
Additional Features
Flight
Instruments
View Messages Sorted by Message Type
While viewing the AUX-TEXT MESSAGING Page, press the ARRANGE
Softkey, then press the TYPE Softkey.
EIS
Or:
a) Press the MENU Key to display the Page Menu.
Nav/Com/
XPDR/Audio
b) Turn either FMS Knob to place the cursor on ‘Sort By Type’.
c) Press the ENT Key. The sorting selection is indicated at the bottom
center of the list window.
AFCS
View Messages Sorted by Address:
GPS Nav
While viewing the AUX-TEXT MESSAGING Page, press the ARRANGE
Softkey, then press the ADDRESS Softkey.
Or:
Flight
Planning
a) Press the MENU Key to display the Page Menu.
b) Turn either FMS Knob to place the cursor on ‘Sort By Address’.
Procedures
c) Press the ENT Key. The sorting selection is indicated at the bottom
center of the list window.
Additional
Features
Hazard
Avoidance
Viewing The Content of a Text Message
1)
While viewing the AUX-TEXT MESSAGING Page, select the desired message box.
2)
Press the FMS Knob to activate the cursor.
3)
Turn either FMS Knob to select the desired message.
4)
Press the VIEW Softkey.
Abnormal
Operation
Or:
Press the ENT Key.
Annun/
Alerts
Or:
a) Press the MENU Key to display the Page Menu.
b) Turn either FMS Knob to place the cursor on ‘View Selected Message’.
Appendix
c) Press the ENT Key.
5)
To close the text message, press the CLOSE Softkey.
Index
Or:
94
Garmin G1000 Cockpit Reference Guide for the Diamond DA42NG
190-00963-04 Rev. A
Additional Features
Flight
Instruments
a) Press the MENU Key to display the Page Menu.
b) Turn either FMS Knob to place the cursor on ‘Close Message’.
c) Press the ENT Key.
2)
Turn either FMS Knob to select the desired message.
3)
Press the MRK READ Softkey.
AFCS
While viewing the Inbox on the AUX-TEXT MESSAGING Page, press the
FMS Knob to activate the cursor.
Nav/Com/
XPDR/Audio
1)
EIS
Mark Selected Message As Read
Or:
GPS Nav
a) Press the MENU Key to display the Page Menu.
b) Turn either FMS Knob to place the cursor on ‘Mark Selected Message
As Read’.
Flight
Planning
c) Press the ENT Key.
The message symbol now indicates the message has been opened.
Turn either FMS Knob to place the cursor on ‘Mark All New Messages As
Read’.
3)
Press the ENT Key. A confirmation window is displayed.
4)
With cursor highlighting ‘YES’, press the ENT Key. The message symbols
now indicate all the message have been opened.
Abnormal
Operation
2)
Additional
Features
While viewing the Inbox on the AUX-TEXT MESSAGING Page, press the
MENU Key to display the Page Menu.
Hazard
Avoidance
1)
Procedures
Mark All Messages As Read
Delete a Message
2)
Turn either FMS Knob to select the desired message.
3)
Press the DELETE Softkey.
Appendix
While viewing the Inbox on the AUX-TEXT MESSAGING Page, press the
FMS Knob to activate the cursor.
Annun/
Alerts
1)
Or:
b) Turn either FMS Knob to place the cursor on ‘Delete Selected Message’.
c) Press the ENT Key.
190-00963-04 Rev. A
Garmin G1000 Cockpit Reference Guide for the Diamond DA42NG
95
Index
a) Press the MENU Key to display the Page Menu.
AFCS
Nav/Com/
XPDR/Audio
EIS
Flight
Instruments
Additional Features
WI-FI CONNECTIONS
The system can connect to a IEEE 802.11g compatible network provided the
aircraft is on the ground and located within range of the network. The system is
capable of WEP64, WEP128,WPA-PSK, and WPA2-PSK encryption formats. WPAEnterprise and WPA2-Enterprise are not supported. Connections that require web
proxies, captive portals, or other elements that require user credentials, including a
username and password or a redemption or access code; or require action such as
accepting a user agreement, are not supported.
Control and monitoring of Wi-Fi functions are accomplished through the AUXWI-FI SETUP Page.
Flight
Planning
GPS Nav
View the Wi-Fi Setup Page
1)
Turn the large FMS Knob on the MFD to select the AUX page group.
2)
Turn the small FMS Knob to select the AUX - WI-FI SETUP.
Hazard
Avoidance
Procedures
Set Up a New Wi-Fi Connection
1)
Select the AVAIL Softkey on the MFD. A list of available networks will
be displayed in the AVAILABLE NETWORKS window. Signal strength is
shown for each network, as well as security requirements and whether the
network has been saved in the system’s memory.
2)
If necessary, select the RESCAN Softkey to have the system scan again for
available networks.
Additional
Features
Or:
a) Press the MENU Key to display the Page Menu.
Abnormal
Operation
b) Turn either FMS Knob to place the cursor on ‘Rescan Available
Networks’.
Appendix
Annun/
Alerts
c) Press the ENT Key.
3)
Press the FMS Knob to place the cursor in the list of networks.
4)
Turn either FMS Knob to select the desired network.
5)
Select the CONNECT Softkey.
Or:
a) Press the MENU Key to display the Page Menu.
Index
b) Turn either FMS Knob to place the cursor on ‘Connect To Selected
Network’.
96
Garmin G1000 Cockpit Reference Guide for the Diamond DA42NG
190-00963-04 Rev. A
Additional Features
7)
Press the ENT Key. ‘OK’ will be highlighted.
8)
Press the ENT Key again.
9)
The SAVE SETTINGS window is now displayed with the cursor highlighting
‘SAVE CONNECTION’.
Nav/Com/
XPDR/Audio
If the network is secured, a window will be displayed in order to enter
the necessary passcode. Use the FMS Knobs to enter the desired alpha
numeric characters. Select the CAP LOCK Softkey to enter upper case
letters. If there is no security associated with the network, proceed to step
9.
EIS
6)
Flight
Instruments
c) Press the ENT Key.
AFCS
GPS Nav
10) The selected network can be saved to system memory to make reconnection easier at a later time.
To connect the selected network without saving:
Flight
Planning
a) Turn the large FMS Knob to move the cursor to highlight ‘CONNECT’.
b) Press the ENT Key.
Procedures
To save and connect the selected network:
a) Press the ENT Key. A checkmark is placed in the checkbox and the
cursor moves to the airport field.
b) Using the FMS Knobs, enter an airport identifier to be associated with
the saved network. This aids in identifying the network later in the
event of duplicate network names.
Hazard
Avoidance
c) Press the ENT Key. The cursor moves to ‘CONNECT’.
Additional
Features
d) Press the ENT Key again to connect to the selected network.
Abnormal
Operation
Edit a Saved Network
Turn either FMS Knob to highlight the network to be edited.
3)
Pressing the ENT Key at this point will check or uncheck the AUTO
CONNECT checkbox. When a checkmark is present, the system will
automatically connect to the network when within range.
4)
Select the EDIT Softkey. The cursor now appears in the CONNECTION
SETTINGS window.
5)
Turn the large FMS Knob to select the network attribute to be edited.
190-00963-04 Rev. A
Garmin G1000 Cockpit Reference Guide for the Diamond DA42NG
Index
2)
Appendix
While viewing list of saved networks, press the FMS Knob to activate the
cursor.
Annun/
Alerts
1)
97
EIS
Flight
Instruments
Additional Features
6)
Turn the small FMS Knob to begin editing the field.
7)
When the entry is complete, press the ENT Key.
8)
Turn the large FMS Knob or press the ENT Key until ‘SAVE’ is highlighted.
9)
Press the ENT Key.
Nav/Com/
XPDR/Audio
Disconnect a Wi-Fi Network
Select the DISCNCT Softkey.
Or:
AFCS
a) Press the MENU Key to display the Page Menu.
GPS Nav
b) Turn either FMS Knob to place the cursor on ‘Disconnect From
Network’.
c) Press the ENT Key.
1)
While viewing the list of saved networks, press the FMS Knob to activate
the cursor.
2)
Turn either FMS Knob to highlight the network to be deleted.
3)
Select the DELETE Softkey. The selected network is removed from the list.
ELECTRONIC STABILITY AND PROTECTION (ESP™)
NOTE: Refer to the Airplane Flight Manual to determine approval of ESP
functionality.
The pilot can interrupt ESP™ by pressing and holding the Autopilot Disconnect (AP
DISC) switch. Upon releasing the or AP DISC switch, ESP™ force will again be applied,
provided aircraft roll attitude is within engagement limits. ESP™ can also be overridden
by overpowering the servo’s mechanical torque limit.
ESP™ can be enabled or disabled on the AUX-SYSTEM SETUP 2 Page on the MFD.
To enable or disable ESP™:
Index
Appendix
Annun/
Alerts
Abnormal
Operation
Additional
Features
Hazard
Avoidance
Procedures
Flight
Planning
Delete a Saved Wi-Fi Network:
98
1)
Turn the large FMS Knob to select the AUX Page Group.
2)
Turn the small FMS Knob to select the AUX - SYSTEM SETUP 1 page.
3)
If necessary, press the SETUP 2 Softkey to display the AUX-SYSTEM SETUP 2
Page. If the AUX-SYSTEM SETUP 2 is already displayed, proceed to step 4.
Garmin G1000 Cockpit Reference Guide for the Diamond DA42NG
190-00963-04 Rev. A
Additional Features
5)
Turn the large FMS Knob to place the cursor in the STABILITY &
PROTECTION field.
6)
Turn the small FMS Knob to select ‘ENABLE’ or ‘DISABLE’.
7)
EIS
Press the FMS Knob to activate the cursor.
Flight
Instruments
4)
Press the FMS Knob to remove the cursor.
Additional
Features
Abnormal
Operation
Annun/
Alerts
Appendix
Index
99
Hazard
Avoidance
Garmin G1000 Cockpit Reference Guide for the Diamond DA42NG
Procedures
190-00963-04 Rev. A
Flight
Planning
High Airspeed Protection
Exceeding Vne will result in ESP™ applying force to raise the nose of the aircraft.
When the high airspeed condition is remedied, ESP™ force is no longer applied.
GPS Nav
Pitch Engagement
ESP™ engages at 16° nose-up and 22° nose-down. Once ESP™ is engaged, it will
apply increasing opposing force between 16° and 20° nose-up and between 22° and
25° nose-down. Maximum opposing force is applied between 20° and 50° nose-up and
between 25° and 50° nose-down. ESP™ disengages when 50° is exceeded in a nose-up
or nose-down attitude.
With ESP™ engaged, and the aircraft in a nose-up condition, opposing force steadily
decreases from 20° nose-up to 12° nose-up as aircraft pitch moves toward zero degrees.
ESP™ disengages at 12° nose-up. With ESP™ engaged, and the aircraft in a nose-down
condition, opposing force steadily decreases from 25° nose-down to 17° nose-down as
aircraft pitch moves toward zero degrees. ESP™ disengages at 17° nose-down.
The opposing force increases or decreases depending on the pitch angle and the
direction of pitch travel. This force is intended to encourage movement in the pitch axis
in the direction of the normal pitch attitude range for the aircraft.
There are no indications marking the pitch ESP™ engage and disengage limits in these
nose-up/nose-down conditions.
AFCS
Roll Engagement
Roll Limit Indicators are displayed on the roll scale at 45° right and left, indicating
where ESP™ will engage. As roll attitude exceeds 45°, ESP™ will engage and the on-side
Roll Limit Indicator will move to 30°. The Roll Limit Indicator is now showing where
ESP™ will disengage as roll attitude decreases to within the desirable roll attitude range.
Once engaged, ESP™ force will be applied between 30° and 75°. The force increases
as roll attitude increases and decreases as roll attitude decreases. The applied force is
intended to encourage pilot input that returns the airplane to a more normal roll attitude. As roll attitude decreases, ESP™ will disengage at 30°
Nav/Com/
XPDR/Audio
ESP is automatically enabled on system power up.
™
AUXILIARY VIDEO (OPTIONAL)
NOTE: Images provided on the Aux-Video page are for supplemental use only.
There are four modes of operation of the optional auxiliary video display: FullScreen, Full-Screen with Digital Zoom, Split-Screen with Map, and Split-Screen with
Map and Digital Zoom.
Displaying auxiliary video:
1) Turn the large FMS Knob to select the AUX page group.
AFCS
Nav/Com/
XPDR/Audio
EIS
Flight
Instruments
Additional Features
2)
GPS Nav
The video display softkeys shown below appear on the AUX - VIDEO Page.
Control of the AUX - VIDEO Page can also be accessed through the Page Menu.
Hazard
Avoidance
Procedures
Flight
Planning
Selecting video menu options:
1) While viewing the AUX - VIDEO Page press the MENU Key to display the
Page Menu OPTIONS.
2)
Turn the large FMS Knob to highlight the desired video adjustment option
and press the ENT Key.
When the ENT key is pressed on any option, the page menu closes and returns to
the AUX - VIDEO Page.
Video Setup
Video brightness, contrast, and saturation may be adjusted be selecting the setup
function. While viewing the setup function softkeys, after 45 seconds of softkey
inactivity, the system reverts to the AUX - VIDEO Page softkeys.
Abnormal
Operation
Additional
Features
Turn the small FMS Knob to select the AUX-VIDEO Page.
Index
Appendix
Annun/
Alerts
Adjusting the video settings:
1) With the AUX-VIDEO Page displayed, press the SETUP Softkey.
2) Press the BRIGHT - or BRIGHT +, to adjust display brightness in five
percent increments from 0 to 100%.
3) Press the CNTRST- or CNTRST +, to adjust display contrast in five
percent increments from 0 to 100%.
4) Press the SAT - or SAT +, to adjust display saturation in five percent
increments from 0 to 100%.
100
Garmin G1000 Cockpit Reference Guide for the Diamond DA42NG
190-00963-04 Rev. A
Additional Features
If desired, return the display to the default settings by pressing the RESET
Softkey.
6)
Press the BACK Softkey to return to the previous softkey level.
GPS Nav
Flight
Planning
Procedures
Hazard
Avoidance
Additional
Features
Abnormal
Operation
Annun/
Alerts
Entering a Scheduler Message
AFCS
SCHEDULER
The Scheduler feature can be used to enter and display reminder messages (e.g.,
Hot Section Inspection or Phase 1 Maintenance Check) in the Messages Window on
the PFD. Messages can be set to display based on a specific date and time (event), once
the message timer reaches zero (one-time; default setting), or recurrently whenever
the message timer reaches zero (periodic). Message timers set to periodic alerting
automatically reset to the original timer value once the message is displayed. When
power is cycled, all messages are retained until deleted, and message timer countdown
is resumed.
Nav/Com/
XPDR/Audio
Zoom/Range
Pressing the VID ZM + or VID ZM - Softkeys increases or decreases video display
magnification between 1x and 10x.
The RANGE Knob can be used to increase or decrease the range setting on the
map display or zoom in and out on the video display. While in the Split-Screen
mode, pressing the MAP ACTV or VID ACTV Softkey determines which display the
RANGE Knob adjusts. Pressing the softkey to display MAP ACTV allows the RANGE
Knob to control the range setting of the map display. Pressing the softkey to display
VID ACTV allows the RANGE Knob to control the zoom setting of the video display.
EIS
Display Selection
Pressing the HIDE MAP Softkey removes the map and displays video on the full
screen. The softkey label changes to grey with black characters. Pressing the HIDE
MAP Softkey again restores the map view and the small video image. The softkey label
returns to white characters on a black background.
Flight
Instruments
5)
1) Select the AUX - UTILITY Page.
3)
Turn the large FMS Knob to highlight the first empty scheduler message
naming field.
4)
Use the FMS Knob to enter the message text to be displayed in the Alerts
Window and press the ENT Key.
190-00963-04 Rev. A
Garmin G1000 Cockpit Reference Guide for the Diamond DA42NG
101
Index
Press the FMS Knob momentarily to activate the flashing cursor.
Appendix
2)
Flight
Instruments
Additional Features
5)
Press the ENT Key again or use the large FMS Knob to move the cursor to
the field next to Type.
6)
Turn the small FMS Knob to select the message type:
EIS
• Event—Message issued at the specified date/time
Nav/Com/
XPDR/Audio
• One-time—Message issued when the message timer reaches zero
(default setting)
GPS Nav
AFCS
• Periodic—Message issued each time the message timer reaches zero
7)
Press the ENT Key again or use the large FMS Knob to move the cursor to
the next field.
8)
For periodic and one-time message, use the FMS Knob to enter the timer
value (HH:MM:SS) from which to countdown and press the ENT Key.
9)
For event-based messages:
Flight
Planning
a) Use the FMS Knob to enter the desired date (DD-MM-YY) and press
the ENT Key.
Procedures
b) Press the ENT Key again or use the large FMS Knob to move the cursor
to the next field.
c) Use the FMS Knob to enter the desired time (HH:MM) and press the
ENT Key.
Deleting a Scheduler Message
1) Select the AUX - UTILITY Page.
Index
Appendix
Annun/
Alerts
Abnormal
Operation
Additional
Features
Hazard
Avoidance
10) Press the ENT Key again or use the large FMS Knob to move the cursor to
enter the next message.
2)
Press the FMS Knob momentarily to activate the flashing cursor.
3)
Turn the large FMS Knob to highlight the name field of the scheduler
message to be deleted.
4)
Press the CLR Key to clear the message text. If the CLR Key is pressed
again, the message is restored.
5)
Press the ENT Key while the message line is cleared to clear the message
text.
Scheduler messages appear in the Messages Window on the PFD. When a scheduler
message is waiting, the MSG Softkey label flashes. Selecting the MSG Softkey opens
the Messages Window and acknowledges the scheduler message. Selecting the MSG
Softkey again removes the Messages Window from the display, and the scheduler
message is deleted from the message queue.
102
Garmin G1000 Cockpit Reference Guide for the Diamond DA42NG
190-00963-04 Rev. A
Additional Features
Nav/Com/
XPDR/Audio
Creating a Profile
1) Use the FMS Knob to select the AUX - System Setup Page.
Press the FMS Knob momentarily to activate the flashing cursor.
AFCS
2)
3) Turn the large FMS Knob to highlight ‘CREATE’ in the Pilot Profile Box.
Press the ENT Key. A ‘Create Profile’ window is displayed.
GPS Nav
4)
5) Use the FMS Knob to enter a profile name up to 16 characters long and
7)
Press the ENT Key.
Hazard
Avoidance
In the next field, use the small FMS Knob to select the desired settings
upon which to base the new profile. Profiles can be created based on
Garmin factory defaults, default profile settings (initially based on Garmin
factory defaults unless edited by the pilot), or current system settings.
Procedures
6)
Flight
Planning
press the ENT Key. Pilot profile names cannot begin with a blank as the
first letter.
8) With ‘CREATE’ highlighted, press the ENT Key to create the profile.
Additional
Features
Or:
Use the large FMS Knob to select ‘CREATE and ACTIVATE’ and press the
ENT Key to activate the new profile.
To cancel the process, select ‘CANCEL’ with the large FMS Knob and press
the ENT Key.
Abnormal
Operation
9)
EIS
When the system is powered on, the last selected pilot profile is shown on the MFD
power-up screen. The system can store up to 25 profiles; the currently active profile,
the amount of memory used, and the amount of memory available are shown at the
top of the AUX - System Setup Page in the box labeled ‘Pilot Profile’.
Flight
Instruments
PILOT PROFILES
10) Press the FMS Knob to deactivate the cursor.
Annun/
Alerts
Selecting an Active Profile
2)
Appendix
1) Use the FMS Knob to select the AUX - System Setup Page.
Press the FMS Knob momentarily to activate the flashing cursor.
3) Turn the large FMS Knob to highlight the active profile field in the Pilot
4) Turn the small FMS Knob to display the pilot profile list and highlight the
desired profile.
190-00963-04 Rev. A
Garmin G1000 Cockpit Reference Guide for the Diamond DA42NG
103
Index
Profile Box.
Additional Features
the selected profile.
6)
Press the FMS Knob to deactivate the cursor.
Renaming a Profile
1) Use the FMS Knob to select the AUX - System Setup Page.
Nav/Com/
XPDR/Audio
EIS
Flight
Instruments
5) Press the ENT Key. The system loads and displays the system settings for
2)
Press the FMS Knob momentarily to activate the flashing cursor.
3) Turn the large FMS Knob to highlight ‘RENAME’ in the Pilot Profile Box.
AFCS
4)
Press the ENT Key.
5) In the ‘Rename Profile’ window, turn the FMS Knob to select the profile to
GPS Nav
rename.
6)
Press the ENT Key.
7) Use the FMS Knob to enter a new profile name up to 16 characters long
Flight
Planning
and press the ENT Key.
8) With ‘RENAME’ highlighted, press the ENT Key.
To cancel the process, use the large FMS Knob to select ‘CANCEL’ and
press the ENT Key.
10) Press the FMS Knob to deactivate the cursor.
Deleting a Profile
Additional
Features
Hazard
Avoidance
Procedures
9)
NOTE: The profile that is currently active cannot be deleted. If this is the
Abnormal
Operation
desired profile to delete, select another profile, then delete the desired
profile.
Annun/
Alerts
2)
Appendix
1) Use the FMS Knob to select the AUX - System Setup Page.
4)
Press the FMS Knob momentarily to activate the flashing cursor.
3) Turn the large FMS Knob to highlight ‘DELETE’ in the Pilot Profile Box.
Press the ENT Key.
5) In the ‘Delete Profile’ window, turn the FMS Knob to select the profile to
Index
delete.
6)
Press the ENT Key.
7) With ‘DELETE’ highlighted, press the ENT Key.
104
Garmin G1000 Cockpit Reference Guide for the Diamond DA42NG
190-00963-04 Rev. A
Additional Features
To cancel the process, use the large FMS Knob to select ‘CANCEL’ and
press the ENT Key.
9)
Press the FMS Knob to deactivate the cursor.
Flight
Instruments
8)
EIS
Importing a Profile from an SD Card
If desired, the profile name to be used after profile has been imported can
be changed by turning the FMS Knob to highlight the ‘PROFILE NAME’
field, then use the large and small FMS Knobs to enter the name, and press
the ENT Key. Imported profile names cannot begin with a blank space or
be named ‘DEFAULT’, ‘GARMIN DEFAULTS’ or ‘DEFAULT SETTINGS’.
6)
With ‘IMPORT’ highlighted, press the ENT Key.
7)
If the imported profile name is the same as an existing profile on the
system, the system displays an ‘Overwrite existing file? OK or CANCEL’
prompt. Press the ENT Key to replace profile on the system with the profile
imported from the SD card, or turn the FMS Knob to highlight ‘CANCEL’
and press the ENT Key to return to the Pilot Profile Importing Window.
8)
If successful, the system displays ‘Pilot profile import succeeded.’ in the
IMPORT RESULTS window below. With ‘OK’ highlighted, press the ENT or
CLR Keys or press the FMS Knob to return to the AUX - System Setup Page.
The imported profile becomes the active profile.
Exporting a Profile to an SD Card
2)
Turn the FMS Knob to select the AUX - System Setup Page.
3)
If necessary, activate the desired pilot profile to export. Only the currently
active Pilot Profile can be exported.
190-00963-04 Rev. A
Garmin G1000 Cockpit Reference Guide for the Diamond DA42NG
105
Index
Insert the SD card for storing the Pilot Profile into the top card slot on the
MFD.
Appendix
1)
Annun/
Alerts
5)
Abnormal
Operation
The system displays the Pilot Profile Importing Window with ‘IMPORT’
highlighted. To change the selected profile to be imported from the SD card
(shown as ‘SELECT FILE’), turn the large FMS Knob to highlight the profile
file name, then turn the small FMS Knob to highlight a profile from the list,
and press the ENT Key.
Additional
Features
4)
Hazard
Avoidance
Select the IMPORT Softkey.
Procedures
3)
Flight
Planning
Turn the FMS Knob to select the AUX - System Setup Page.
GPS Nav
2)
AFCS
Insert an SD card containing the pilot profile(s) into the top card slot on the
MFD.
Nav/Com/
XPDR/Audio
1)
4)
Select the EXPORT Softkey. The system displays the Pilot Profile Exporting
Window.
5)
To export the pilot profile using the current supplied name, press the ENT
Key with ‘EXPORT’ highlighted. To change the profile file name turn the
large FMS Knob to highlight the ‘SELECT FILE’ field, then enter the new
name with the large and small FMS Knobs, then press the ENT Key. Then
press the ENT Key with ‘EXPORT’ highlighted.
6)
If the profile name to be exported is the same as an existing profile file
name on the SD card, the system displays an ‘Overwrite existing file? OK
or CANCEL’ prompt. Press the ENT Key to replace the profile on the SD
card with the profile to be exported, or turn the FMS Knob to highlight
‘CANCEL’ and press the ENT Key to return to the Pilot Profile Exporting
Window without exporting the profile.
7)
If successful, the EXPORT RESULTS window displays ‘Pilot profile export
succeeded.’ With ‘OK’ highlighted, press the ENT or CLR Keys, or press the
FMS Knob to return to the AUX - System Setup Page.
ELECTRONIC CHECKLISTS (OPTIONAL)
The system accesses the checklists from an SD card inserted into the card slot.
If the SD card contains an invalid checklist file or no checklist, the Power-up Page
messages display ‘Checklist File: Invalid’ or ‘Checklist File: N/A’ (not available) and the
CHKLIST Softkey is not available.
The following colors are used for checklist items:
• Light Blue - Items not selected or
• Gray - General notes
checked
• Yellow - Caution notes
• White - Item is selected
• Red - Warning notes
• Green - Item has been checked
Accessing and Navigating Checklists
Index
Appendix
Annun/
Alerts
Abnormal
Operation
Additional
Features
Hazard
Avoidance
Procedures
Flight
Planning
GPS Nav
AFCS
Nav/Com/
XPDR/Audio
EIS
Flight
Instruments
Additional Features
106
1)
From any page on the MFD, select the CHKLIST Softkey. The cursor is now
flashing in the ‘GROUP’ field.
2)
Turn the small FMS Knob to select the desired procedure.
3)
Press the ENT Key.
4)
Turn the small FMS Knob to select the desired checklist.
5)
Press the ENT Key. The first checklist item is indicated with white text
surrounded by a white box.
Garmin G1000 Cockpit Reference Guide for the Diamond DA42NG
190-00963-04 Rev. A
Additional Features
Press the ENT Key or select the CHECK Softkey to check the selected
checklist item. The line item turns green and a checkmark is placed in the
associated box. The next line item is automatically selected for checking.
When all checklist items have been checked, ‘*Checklist Finished*’ is
displayed in green text at the bottom left of the checklist window and
‘GO TO NEXT CHECKLIST?’ is highlighted. If ‘GO TO NEXT CHECKLIST?’
is selected prior to checking all the checklist items, ‘*CHECKLIST NOT
FINISHED*’ will be displayed in yellow text.
8)
Press the ENT Key. If ‘GO TO NEXT CHECKLIST?’ is displayed when
pressing the ENT Key, the next checklist in the group will be displayed. If
‘EXIT CHECKLISTS?’ is displayed when pressing the ENT Key, the system
will exit the Checklist Page.
9)
Select the EXIT Softkey to exit the Checklist Page and return to the page
last viewed. When returning to the Checklist Page after pressing the EXIT
Softkey, the system will return to the last selected checklist item.
AFCS
7)
Procedures
Hazard
Avoidance
3)
Turn the FMS Knob to select the desired emergency checklist and press the
ENT Key.
4)
Press the ENT Key or select the CHECK Softkey to check the selected
emergency checklist item. The line item turns green and a checkmark is
placed in the box next to it. The next line item is automatically highlighted
for checking.
When all checklist items have been checked, ‘*Checklist Finished*’ is
107
Index
Press the CLR Key or select the UNCHECK Softkey to remove a check mark
from an item.
Appendix
Either FMS Knob can be used to scroll through the checklist and select the
desired checklist item.
Annun/
Alerts
Select the EMERGCY Softkey.
Abnormal
Operation
2)
Additional
Features
From any page on the MFD, select the CHKLIST Softkey or turn the large
FMS Knob to select the Checklist Page.
Garmin G1000 Cockpit Reference Guide for the Diamond DA42NG
Flight
Planning
1)
190-00963-04 Rev. A
GPS Nav
Immediately Accessing Emergency Procedures
5)
Nav/Com/
XPDR/Audio
Press the CLR Key or select the UNCHECK Softkey to remove a check mark
from an item.
EIS
Either FMS Knob can be used to scroll through the checklist and select the
desired checklist item.
Flight
Instruments
6)
Additional Features
6)
Press the ENT Key to advance to the next checklist.
7)
Select the RETURN Softkey to return to the previous checklist.
8)
Select the EXIT Softkey to exit the Checklist Page and return to the page
last viewed.
Index
Appendix
Annun/
Alerts
Abnormal
Operation
Additional
Features
Hazard
Avoidance
Procedures
Flight
Planning
GPS Nav
AFCS
Nav/Com/
XPDR/Audio
EIS
Flight
Instruments
displayed in green text at the bottom left of the checklist window and
‘GO TO NEXT CHECKLIST?’ is highlighted. If ‘GO TO NEXT CHECKLIST?’
is selected prior to checking all the checklist items, ‘*CHECKLIST NOT
FINISHED*’ will be displayed in yellow text.
108
Garmin G1000 Cockpit Reference Guide for the Diamond DA42NG
190-00963-04 Rev. A
Abnormal Operation
Flight
Instruments
ABNORMAL OPERATION
REVERSIONARY MODE
Nav/Com/
XPDR/Audio
Reversionary display mode can be manually activated by pressing the DISPLAY
BACKUP Button on the audio panel.
EIS
Should a system detected failure occur in either display, the G1000 automatically
enters reversionary mode. In reversionary mode, critical flight instrumentation is
combined with engine instrumentation on the remaining display.
AFCS
Additional
Features
If GPS position is lost, or becomes invalid, selected hazards being displayed on the
Navigation Map Page are removed until GPS position is again established.
Hazard
Avoidance
HAZARD DISPLAYS WITH LOSS OF GPS POSITION
Procedures
When a COM tuning failure is detected by the system, the emergency frequency
(121.500 MHz) is automatically loaded into the active frequency field of the COM
radio for which the tuning failure was detected.
Flight
Planning
ABNORMAL COM OPERATION
GPS Nav
NOTE: The Diamond DA42NG Pilot’s Operating Handbook (POH) always takes
precedence over the information found in this section.
Abnormal
Operation
Annun/
Alerts
Loss of Hazard Functions with Loss of GPS
Position
Appendix
Index
190-00963-04 Rev. A
Garmin G1000 Cockpit Reference Guide for the Diamond DA42NG
109
UNUSUAL ATTITUDES
The PFD ‘declutters’ when the aircraft enters an unusual attitude. Only the primary
functions are displayed in these situations.
The following information is removed from the PFD (and corresponding softkeys
are disabled) when the aircraft experiences unusual attitudes:
• Traffic Annunciations
• AFCS Annunciations
• Flight Director
Command Bars
• Inset Map
• Temperatures
• DME Information
Window
• Wind Data
• Selected Heading Box
• Selected Course Box
• Transponder Status
Box
• System Time
• PFD Setup Menu
• Windows displayed in
the lower right corner
of the PFD:
– Timer/References
– Nearest Airports
– Flight Plan
– Messages
– Procedures
– ADF/DME Tuning
• Barometric Minimum
Descent Altitude Box
• Glideslope, Glidepath, and Vertical
Deviation Indicators
• Altimeter Barometric
Setting
• Selected Altitude
• VNV Target Altitude
Extreme Pitch Indication
DEAD RECKONING
While in Enroute or Oceanic phase of flight, if the G1000 detects an invalid GPS
solution or is unable to calculate a GPS position, the system automatically reverts to
Dead Reckoning (DR) Mode. In DR Mode, the G1000 uses its last-known position
combined with continuously updated airspeed and heading data (when available) to
calculate and display the aircraft’s current estimated position.
Index
Appendix
Annun/
Alerts
Abnormal
Operation
Additional
Features
Hazard
Avoidance
Procedures
Flight
Planning
GPS Nav
AFCS
Nav/Com/
XPDR/Audio
EIS
Flight
Instruments
Abnormal Operation
110
Garmin G1000 Cockpit Reference Guide for the Diamond DA42NG
190-00963-04 Rev. A
Abnormal Operation
EIS
Nav/Com/
XPDR/Audio
AFCS
GPS Nav
Flight
Planning
Procedures
Hazard
Avoidance
Additional
Features
Abnormal
Operation
DR Mode is indicated on the G1000 by the appearance of the letters ‘DR’
superimposed in yellow over the ‘own aircraft’ symbol as shown in the following
figure. In addition, ‘DR’ is prominently displayed, also in yellow, on the HSI slightly
above and to the right of the aircraft symbol on the CDI as shown in the following
figure. Also, the CDI deviation bar is removed from the display. Lastly, but at the same
time, a ‘GPS NAV LOST’ alert message appears on the PFD.
Normal navigation using GPS source data resumes automatically once a valid GPS
solution is restored.
It is important to note that estimated navigation data supplied by the G1000 in
DR Mode may become increasingly unreliable and must not be used as a sole means
of navigation. If, while in DR Mode, airspeed and/or heading data is also lost or
not available, the DR function may not be capable of estimating your position and,
consequently, the system may display a path that is different than the actual movement
of the aircraft. Estimated position information displayed by the G1000 through
DR while there is no heading and/or airspeed data available should not be used for
navigation.
DR Mode is inherently less accurate than the standard GPS Mode due to the lack of
satellite measurements needed to determine a position. Changes in wind speed and/
or wind direction compounds the relative inaccuracy of DR Mode. Because of this
degraded accuracy, the crew must maintain position awareness using other navigation
equipment until GPS-derived position data is restored.
Flight
Instruments
NOTE: Dead Reckoning Mode only functions in Enroute (ENR) or Oceanic
(OCN) phase of flight. In all other phases, an invalid GPS solution produces
a “NO GPS POSITION” annunciation on the map and the G1000 stops
navigating in GPS Mode.
Annun/
Alerts
Appendix
CDI ‘DR’ Indication on PFD
Symbolic Aircraft
(Map pages and Inset Map)
Index
Dead Reckoning Indications
190-00963-04 Rev. A
Garmin G1000 Cockpit Reference Guide for the Diamond DA42NG
111
As a result of operating in DR Mode, all GPS-derived data is computed based upon
an estimated position and is displayed as yellow text on the display to denote degraded
navigation source information. This data includes the following:
• Navigation Status Box fields except Active Leg, TAS, and DTK
• GPS Bearing Pointer
• Wind data and pointers in the Wind Data Box on the PFD
• Track Indicator
• All Bearing Pointer Distances
• Active Flight Plan distances, bearings, and ETE values
Also, while the G1000 is in DR Mode, the autopilot will not couple to GPS, and
Terrain Proximity is disabled. Additionally, the accuracy of all nearest information
(airports, airspaces, and waypoints) is questionable. Finally, airspace alerts continue
to function, but with degraded accuracy.
Index
Appendix
Annun/
Alerts
Abnormal
Operation
Additional
Features
Hazard
Avoidance
Procedures
Flight
Planning
GPS Nav
AFCS
Nav/Com/
XPDR/Audio
EIS
Flight
Instruments
Abnormal Operation
112
Garmin G1000 Cockpit Reference Guide for the Diamond DA42NG
190-00963-04 Rev. A
Annunciations & Alerts
R GBOX TEMP
Right engine gearbox temp is >120 deg C.
NO TAKEOFF
Aircraft skin temperature is too warm to safely
fly the aircraft.
L OIL TEMP
Left engine oil temp is greater than 140 deg C.
R OIL TEMP
Right engine oil temp is greater than 140 deg C.
190-00963-04 Rev. A
Garmin G1000 Cockpit Reference Guide for the Diamond DA42NG
Index
L STARTER
Appendix
R OIL PRES
Left engine oil pressure is less than 1.5 bar with
system software 0670.05 and earlier, or 0.9 bar
with system software 0670.06 or later.
Right engine oil pressure is less than 1.5 bar
with system software 0670.05 and earlier, or 0.9
bar with system software 0670.06 or later.
Left engine starter is engaged.
Annun/
Alerts
L OIL PRES
Abnormal
Operation
Left engine gearbox temp is >120 deg C.
Additional
Features
L GBOX TEMP
Continuous
Aural Tone
Hazard
Avoidance
Right fuel temp is greater than 60 deg C.
Procedures
R FUEL TEMP
Flight
Planning
Left fuel temp is greater than 60 deg C.
GPS Nav
L FUEL TEMP
AFCS
Right engine fuel pressure is low.
Nav/Com/
XPDR/Audio
R FUEL PRESS
Audio Alert
EIS
WARNING ALERTS
Annunciation
Alerts Window Message
Window Text
L ALTN AMPS Left engine alternator output is >70 amps.
R ALTN AMPS Right engine alternator output is >70 amps.
AP TRIM FAIL* Autopilot automatic trim is inoperative.
DOOR OPEN
Front, rear, or baggage door is not closed.
L ENG FIRE
Left engine fire detected.
R ENG FIRE
Right engine fire detected.
L ENG TEMP
Left engine coolant temp is >105 deg C.
R ENG TEMP
Right engine coolant temp is >105 deg C.
L FUEL PRESS Left engine fuel pressure is low.
Flight
Instruments
ANNUNCIATIONS & ALERTS
113
Index
Appendix
Annun/
Alerts
Abnormal
Operation
Additional
Features
Hazard
Avoidance
Procedures
Flight
Planning
GPS Nav
AFCS
Nav/Com/
XPDR/Audio
EIS
Flight
Instruments
Annunciations & Alerts
Annunciation
Window Text
R STARTER
USP ACTIVE**
Alerts Window Message
Audio Alert
Right engine starter is engaged.
USP has engaged autopilot due to slow airspeed.
Continuous
Aural Tone
* Optional (KAP 140 equipped aircraft only)
** Optional (Garmin AFCS equipped aircraft with ESP™ only)
CAUTION ALERTS
Annunciation
Window Text
Alerts Window Message
The alternate air intake door on the left engine is
open.
The alternate air intake door on the right engine
R ALT AIR OPEN
is open.
L ALTN FAIL
Left engine alternator has failed.
R ALTN FAIL
Right engine alternator has failed.
L AUX FUEL E* Left auxiliary fuel tank is empty.
R AUX FUEL E* Right auxiliary fuel tank is empty.
CHECK GEAR Landing gear is not down and locked
L COOL LVL
Left engine coolant level is low.
R COOL LVL
Right engine coolant level is low.
DEICE LVL LO* De-icing fluid level is low.
DEIC PRES HI* De-icing pressure is high.
DEIC PRES LO* De-icing pressure is low.
L ECU A FAIL
Left engine ECU A has failed.
R ECU A FAIL
Right engine ECU A has failed.
L ECU B FAIL
Left engine ECU B has failed.
R ECU B FAIL
Right engine ECU B has failed.
L FUEL LOW
Left engine main tank fuel quantity is low.
R FUEL LOW
Right engine main tank fuel quantity is low.
NO ADC MODES Autopilot air data modes are not available.
NO VERT MODES Autopilot vertical modes are not available.
Audio Alert
L ALT AIR OPEN
114
Garmin G1000 Cockpit Reference Guide for the Diamond DA42NG
Single Aural
Tone
190-00963-04 Rev. A
Annunciations & Alerts
Alerts Window Message
EIS
Single Aural
Tone
Nav/Com/
XPDR/Audio
AFCS
Pitot heat has failed.
Pitot heat is off.
Stall warning heat has failed.
Stall warning heat is off.
Stick limiting system has failed.
Left bus voltage is less than 25 volts.
Right bus voltage is less than 25 volts.
Audio Alert
Flight
Instruments
Annunciation
Window Text
PITOT FAIL
PITOT HT OFF
STAL HT FAIL
STAL HT OFF
STICK LIMIT
L VOLTS LOW
R VOLTS LOW
* Optional
GPS Nav
Audio Alert
Flight
Planning
Procedures
No Tone
Hazard
Avoidance
ANNUNCIATION ADVISORY
Annunciation
Alerts Window Message
Window Text
L AUXPUMP ON* Left fuel transfer from aux to main in progress.
R AUXPUMP ON* Right fuel transfer from aux to main in progress.
L GLOW ON
Left engine glow plug active.
R GLOW ON
Right engine glow plug active.
* Optional
Alerts Window Message
None
Appendix
Index
Garmin G1000 Cockpit Reference Guide for the Diamond DA42NG
Annun/
Alerts
190-00963-04 Rev. A
Abnormal
Operation
PFD FAN FAIL – The cooling fan for the PFD is inoperative.
MFD FAN FAIL – The cooling fan for the MFD is inoperative.
GIA FAN FAIL – The cooling fan for the GIAs is inoperative.
ESP DEGRADE* – ESP IAS mode is inoperative.
ESP FAIL* – ESP is inoperative.
ESP OFF* – ESP selected off.
ESP CONFIG* – ESP config error. Config service req’d.
FAILED AP PATH – An autopilot servo data path has failed.
* Garmin AFCS equipped aircraft with ESP™
Audio
Alert
Additional
Features
MESSAGE ADVISORY ALERTS
115
EIS
Flight
Instruments
Annunciations & Alerts
AFCS ALERTS
Alert Condition
Rudder Mistrim Right
Nav/Com/
XPDR/Audio
Rudder Mistrim Left
Aileron Mistrim Right
Elevator Mistrim
Down
Elevator Mistrim Up
Description
Yaw servo providing sustained force in the
indicated direction
Roll servo providing sustained force in
indicated direction
Pitch servo providing sustained force in the
indicated direction
(or Stuck AP TRIM
Switch)
If AP engaged, take control of the aircraft
and disengage AP
If AP disengaged, move AP TRIM switches
separately to unstick
Yaw Damper Failure
YD control failure
Pitch Trim Failure
Additional
Features
Hazard
Avoidance
Procedures
Flight
Planning
GPS Nav
AFCS
Aileron Mistrim Left
Annunciation
Roll Failure
Roll axis control failure; AP inoperative
Pitch Failure
Pitch axis control failure; AP inoperative
Annun/
Alerts
Abnormal
Operation
System Failure
Index
Appendix
Preflight Test
116
AP and MET are unavailable; FD may still be
available
Performing preflight system test; aural alert
sounds at completion
Do not press the AP DISC Switch during
servo power-up and preflight system tests.
Doing so may cause the preflight system
test to fail or never to start. Cycle power to
the servos if this occurs.
Preflight system test failed; aural alert
sounds at failure
Garmin G1000 Cockpit Reference Guide for the Diamond DA42NG
190-00963-04 Rev. A
Annunciations & Alerts
Traffic Display
Enabled Icon
(Other Maps)
EIS
Traffic Mode Annunciation
(Traffic Map Page)
Mode
Flight
Instruments
TAS ALERTS AND ANNUNCIATIONS
Nav/Com/
XPDR/Audio
OPERATING
TAS Operating
FAIL
TAS Failed*
AFCS
TAS Modes
Procedures
Annun/
Alerts
Appendix
NO TRFC DATA
Abnormal
Operation
TRFC FAIL
A Traffic Advisory is outside the selected display
range*
Annunciation is removed when traffic comes within
the selected display range
System cannot determine bearing of Traffic
Advisory**
Annunciation indicates distance in nm, altitude
separation in hundreds of feet, and altitude trend
arrow (climbing/descending)
TAS unit has failed (unit is self-reporting a failure or
sending incorrectly formatted data)
Data is not being received from the TAS unit
Additional
Features
TA X.X ± XX ↕
Description
Hazard
Avoidance
TA OFF SCALE
Index
*Shown as symbol on Traffic Map Page
**Shown in center of Traffic Map Page
TAS Traffic Status Annunciations
190-00963-04 Rev. A
Garmin G1000 Cockpit Reference Guide for the Diamond DA42NG
Flight
Planning
TAS Failure Annunciations
Traffic Status Banner
Annunciation
GPS Nav
Traffic Map Page Annunciation
Description
NO DATA
Data is not being received from the TAS unit
Data is being received from the TAS unit, but the
DATA FAILED
unit is self-reporting a failure
FAILED
Incorrect data format received from the TAS unit
117
Annun/
Alerts
Abnormal
Operation
Additional
Features
Hazard
Avoidance
Procedures
Flight
Planning
GPS Nav
AFCS
Nav/Com/
XPDR/Audio
EIS
Flight
Instruments
Annunciations & Alerts
TIS ALERTS AND ANNUNCIATIONS
Traffic Status
Banner
Annunciation
Description
A Traffic Advisory is outside the selected display range*
TA OFF SCALE Annunciation is removed when traffic comes within the selected
display range
System cannot determine bearing of Traffic Advisory**
TA X.X ± XX ↕ Annunciation indicates distance in nm, altitude separation in
hundreds of feet, and altitude trend arrow (climbing/descending)
Appears if traffic data is not refreshed within 6 seconds
If after another 6 seconds data is not received, traffic is removed
AGE MM:SS from the display
The quality of displayed traffic information is reduced as the age
increases
The displayed data is not current (6 to 12 seconds since last
message)
TRFC COAST
The quality of displayed traffic information is reduced when this
message is displayed
Traffic is removed because it is too old for coasting (12 to 60
seconds since last message)
TRFC RMVD
Traffic may exist within the selected display range, but it is not
displayed
TRFC FAIL
Traffic data has failed
NO TRFC DATA Traffic data has not been detected
TRFC UNAVAIL The traffic service is unavailable or out of range
*Shown as symbol on Traffic Map Page
**Shown in center of Traffic Map Page
Index
Appendix
TIS Traffic Status Banner Annunciations
118
Garmin G1000 Cockpit Reference Guide for the Diamond DA42NG
190-00963-04 Rev. A
Annunciations & Alerts
OPERATING
EIS
TIS Operating
Traffic Display Enabled
Icon
(Other Maps)
Flight
Instruments
Mode
Traffic Mode Annunciation
(Traffic Map Page)
TIS Failed*
FAIL
AFCS
STANDBY
(also shown in white in center of page)
Nav/Com/
XPDR/Audio
TIS Standby
* See Table 6-26 for additional failure annunciations
FAILED
Data is not being received from the transponder*
Data is being received from the transponder, but
a failure is detected in the data stream*
Procedures
DATA FAILED
Description
Flight
Planning
Traffic Map Page
Annunciation
NO DATA
GPS Nav
TIS Modes
UNAVAILABLE
Hazard
Avoidance
The transponder has failed*
TIS is unavailable or out of range
Additional
Features
* Contact a service center or Garmin dealer for corrective action
TIS Failure Annunciations
MFD
Pop-Up Alert
Aural
Message
Annun/
Alerts
Alert Type
PFD/MFD
Terrain-SVS
Page
Annunciation
Abnormal
Operation
SVS TERRAIN ALERTS
Imminent Terrain Impact
Warning (ITI)
“Warning; Terrain,
Terrain”
190-00963-04 Rev. A
Garmin G1000 Cockpit Reference Guide for the Diamond DA42NG
119
Index
“Warning; Terrain,
Terrain”
Appendix
Reduced Required Terrain
Clearance Warning (RTC)
Alert Type
PFD/MFD
Terrain-SVS
Page
Annunciation
MFD
Pop-Up Alert
Aural
Message
Reduced Required Obstacle
Clearance Warning (ROC)
“Warning; Obstacle,
Obstacle”
Imminent Obstacle Impact
Warning (IOI)
“Warning; Obstacle,
Obstacle”
Reduced Required Terrain
Clearance Caution (RTC)
“Caution; Terrain,
Terrain”
Imminent Terrain Impact
Caution (ITI)
“Caution; Terrain,
Terrain”
Reduced Required Obstacle
Clearance Caution (ROC)
“Caution; Obstacle,
Obstacle”
Imminent Obstacle Impact
Caution (IOI)
“Caution; Obstacle,
Obstacle”
SVS TERRAIN STATUS ANNUNCIATIONS
Alert Type
PFD/MFD†
Alert
Annunciation
System Test in Progress
System Test Pass
Terrain Alerting Inhibited
No GPS position
Excessively degraded GPS
signal; or Out of database
coverage area
None
Terrain-SVS Page
Center Banner
Annunciation
TERRAIN TEST
None
None
NO GPS POSITION
None
Voice Alert
None
“Terrain
System Test
OK”
None
“Terrain
System Not
Available”*
“Terrain
System Not
Available”*
Index
Appendix
Annun/
Alerts
Abnormal
Operation
Additional
Features
Hazard
Avoidance
Procedures
Flight
Planning
GPS Nav
AFCS
Nav/Com/
XPDR/Audio
EIS
Flight
Instruments
Annunciations & Alerts
120
Garmin G1000 Cockpit Reference Guide for the Diamond DA42NG
190-00963-04 Rev. A
Annunciations & Alerts
Alert Type
Voice Alert
TERRAIN FAIL
“Terrain
System
Failure”
TERRAIN DATABASE
FAILURE
None
EIS
Nav/Com/
XPDR/Audio
AFCS
None
GPS Nav
Flight
Planning
Terrain System Test
Fail; Terrain or Obstacle
database unavailable or
invalid; Invalid software
configuration; or System
audio fault
MFD Terrain or Obstacle
database unavailable
or invalid, and TerrainSVS operating with
PFD Terrain or Obstacle
databases
Terrain-SVS Page
Center Banner
Annunciation
Procedures
ADS-B ALERTS AND ANNUNCIATIONS
TEST MODE
ADS-B: AIRB
ADS-B: AIRB
ADS-B: SURF
ADS-B: SURF
ADS-B: OFF
ADS-B TRFC OFF
ABD-B Traffic
Off
Appendix
ADS-B: TEST
Annun/
Alerts
ADS-B System
Test Initiated
Traffic Display
Status Icon
(Other Maps)
Abnormal
Operation
Traffic Map Page
Center Banner
Annunciation
Additional
Features
Traffic Mode
Annunciation
(Traffic Map Page)
Hazard
Avoidance
Mode
ADS-B
Operating in
Airborne Mode
ADS-B
Operating in
Surface Mode
Flight
Instruments
PFD/MFD†
Alert
Annunciation
Index
190-00963-04 Rev. A
Garmin G1000 Cockpit Reference Guide for the Diamond DA42NG
121
Annunciations & Alerts
Traffic Map Page
Center Banner
Annunciation
ADS-B Traffic
Not Available
ADS-B: N/A
ADS-B TRFC N/A
ADS-B Failed*
ADS-B: FAIL
ADS-B TRFC FAIL
Nav/Com/
XPDR/Audio
EIS
Flight
Instruments
Traffic Mode
Annunciation
(Traffic Map Page)
Mode
Traffic Display
Status Icon
(Other Maps)
AFCS
Traffic Modes
Traffic Failure Annunciations
Traffic Status Banner
Annunciation
TA OFF SCALE
Abnormal
Operation
Additional
Features
Hazard
Avoidance
Procedures
Flight
Planning
GPS Nav
Traffic Map Page Center
Description
Annunciation
NO DATA
Data is not being received from the traffic unit
Data is being received from the traffic unit, but the
DATA FAILED
unit is self-reporting a failure
ADS-B TRFC FAIL
Incorrect data format received from the traffic unit
Annun/
Alerts
TA X.X ± XX ↕
Index
Appendix
TRFC FAIL
NO TRFC DATA
Description
A Traffic Advisory is outside the selected display range*.
Annunciation is removed when traffic comes within the
selected display range.
System cannot determine bearing of Traffic Advisory**.
Annunciation indicates distance in nm, altitude separation
in hundreds of feet, and altitude trend arrow (climbing/
descending).
Traffic unit has failed (unit is self-reporting a failure or
sending incorrectly formatted data)
Data is not being received from the traffic unit
*Shown as symbol on Traffic Map Page
**Shown in center of Traffic Map Page
Traffic Status Annunciations
122
Garmin G1000 Cockpit Reference Guide for the Diamond DA42NG
190-00963-04 Rev. A
Annunciations & Alerts
Flight
Instruments
WEATHER RADAR ALERTS AND ANNUNCIATIONS
Center Banner Annunciation
Standby
STANDBY
STANDBY
Standby
(During WarmUp), applicable
to GWX 68
only
STANDBY
WARM-UP
XX
(XX indicates number of
seconds remaining in warm-up)
Weather
WEATHER
None
GROUND MAPPING
None
OFF
FAIL
OFF
RADAR FAIL
Flight
Planning
Procedures
Abnormal
Operation
Annun/
Alerts
Appendix
Radar Feature Annunciations on the Weather Radar Page
Additional
Features
STAB INOP
Description
Altitude compensated tilt feature is enabled (GWX 70 only)
Altitude compensated tilt feature is disabled (GWX 70 only)
Antenna stabilization is selected on.
Antenna stabilization is selected off.
The radar is not receiving pitch and roll information. The
antenna stabilization feature is inoperative.
Hazard
Avoidance
Radar Modes on the Weather Radar Page
Radar Feature Status
ACT ON
ACT OFF
STAB ON
STAB OFF
GPS Nav
† Annunciations in this column appear in white text in the Weather Radar Mode box on the Navigation Map Page.
AFCS
Ground
Mapping
Off
Radar Failed*
Nav/Com/
XPDR/Audio
Radar Mode Annunciation
Box†
EIS
Radar Mode
Index
190-00963-04 Rev. A
Garmin G1000 Cockpit Reference Guide for the Diamond DA42NG
123
Annunciations & Alerts
EIS
Flight
Instruments
Weather
Radar Page
Center Banner
Annunciation
Nav/Com/
XPDR/Audio
BAD CONFIG
RDR FAULT
AFCS
RADAR FAIL
The radar configuration is invalid. The radar should be
serviced.
The radar unit is reporting a fault. The radar should be
serviced.
The system is not receiving valid data from the radar unit. The
system should be serviced.
GPS Nav
Abnormal Radar Status Annunciations on the Weather Radar Page
GDL 69A/GDL 69A SXM DATA LINK RECEIVER MESSAGES
Message
Procedures
Flight
Planning
Description
Hazard
Avoidance
CHECK ANTENNA
Additional
Features
UPDATING
Abnormal
Operation
NO SIGNAL
Annun/
Alerts
LOADING
Appendix
OFF AIR
Description
Data Link Receiver
XM Radio Page - active channel
antenna error;
field
service required
Data Link Receiver
XM Radio Page - active channel
updating encryption
field
code
XM Radio Page - active channel
Loss of signal; signal
field
strength too low for
Weather Datalink Page - center
receiver
of page
XM Radio Page - active channel Acquiring channel
field
audio or information
XM Radio Page - active channel Channel not in
field
service
XM Radio Page - active channel Missing channel
field
information
Index
---
Message Location
124
Garmin G1000 Cockpit Reference Guide for the Diamond DA42NG
190-00963-04 Rev. A
Annunciations & Alerts
Message Location
Nav/Com/
XPDR/Audio
DETECTING
ACTIVATION
EIS
WEATHER DATA LINK
FAILURE
Description
No communication
Weather Datalink Page - center from Data Link
of page
Receiver within last
5 minutes
SiriusXM
Weather Datalink Page - center
subscription is not
of page
activated
Flight
Instruments
Message
Description
Procedures
Hazard
Avoidance
Additional
Features
Abnormal
Operation
Issued when the aircraft transitions through the minimum
descent altitude/decision height (MDA/DH)
Aircraft is one minute from Top of Descent - issued only when
vertical navigation is enabled
“Traffic”
TIS voice alert - issued when a Traffic Advisory (TA) is issued
“Traffic Not Available” TIS voice alert - issued when the traffic system fails or cannot
communicate
“Traffic, Traffic”
Played when a Traffic Advisory (TA) is issued (TAS system)
“Traffic Advisory
Played when the TAS system passes a pilot-initiated self test.
System
Test Passed”
“Traffic Advisory
Played when the TAS system fails a pilot-initiated self test.
System
Test Failed”
Flight
Planning
“Minimums,
Minimums”
“Vertical Track”
GPS Nav
Voice Alert
AFCS
VOICE ALERTS
Annun/
Alerts
Appendix
Index
190-00963-04 Rev. A
Garmin G1000 Cockpit Reference Guide for the Diamond DA42NG
125
Index
Appendix
Annun/
Alerts
Abnormal
Operation
Additional
Features
Hazard
Avoidance
Procedures
Flight
Planning
GPS Nav
AFCS
Nav/Com/
XPDR/Audio
EIS
Flight
Instruments
Annunciations & Alerts
MFD & PFD MESSAGE ADVISORIES
Message Advisory
ABORT APR – Loss of GPS navigation.
Abort approach.
ADC1 ALT EC – ADC1 altitude error
correction is unavailable.
ADC1 AS EC – ADC1 airspeed error
correction is unavailable.
AHRS1 CAL – AHRS1 calibration version
error. Srvc req’d.
AHRS1 GPS – AHRS1 using backup
GPS source.
Comments
Abort approach due to loss of GPS
navigation.
GDC1 is reporting that the altitude error
correction is unavailable.
GDC1 is reporting that the airspeed error
correction is unavailable.
The #1 AHRS calibration version error. The system
should be serviced.
The #1 AHRS is using the backup GPS path.
Primary GPS path has failed. The G1000
system should be serviced when possible.
AHRS1 GPS – AHRS1 not receiving
The #1 AHRS is not receiving any or any
any GPS information.
useful GPS information. Check AFMS
limitations. The G1000 system should be
serviced.
AHRS1 GPS – AHRS1 not receiving
The #1 AHRS is not receiving backup GPS
backup GPS information.
information. The G1000 system should be
serviced.
AHRS1 GPS – AHRS1 operating
The #1 AHRS is operating exclusively in
exclusively in no-GPS mode.
no-GPS mode. The G1000 system should be
serviced.
AHRS1 SRVC – AHRS1 Magnetic-field The #1 AHRS earth magnetic field model is
model needs update.
out of date. Update magnetic field model
when practical.
AHRS1 TAS – AHRS1 not receiving
The #1 AHRS is not receiving true airspeed
airspeed.
from the air data computer. The AHRS relies
on GPS information to augment the lack
of airspeed. The G1000 system should be
serviced.
APR DWNGRADE – Approach
Use LNAV minima when approach is
downgraded.
downgraded.
126
Garmin G1000 Cockpit Reference Guide for the Diamond DA42NG
190-00963-04 Rev. A
Annunciations & Alerts
GPS Nav
Flight
Planning
Procedures
Hazard
Avoidance
Additional
Features
Abnormal
Operation
Annun/
Alerts
Appendix
Index
127
AFCS
Garmin G1000 Cockpit Reference Guide for the Diamond DA42NG
Nav/Com/
XPDR/Audio
190-00963-04 Rev. A
EIS
Comments
Special use airspace is ahead of aircraft. The
aircraft will penetrate the airspace within 10
minutes.
ARSPC NEAR – Airspace near – less Special use airspace is within 2 nm of the
than 2 nm.
aircraft position.
ARSPC NEAR – Airspace near and
Special use airspace is near and ahead of the
ahead.
aircraft position.
APR INACTV – Approach is not active. The system notifies the pilot that the loaded
approach is not active. Activate approach
when required.
AUDIO MANIFEST - Audio software The GDC 74B has incorrect software installed.
mismatch, communication halted.
The G1000 system should be serviced.
CHECK CRS – Database course for
Selected course for LOC2 differs from
LOC2 / [LOC ID] is [CRS]°.
published localizer course by more than 10
degrees.
CNFG MODULE – PFD1 configuration The PFD1 configuration module backup
module is inoperative.
memory has failed. The G1000 system should
be serviced.
COM1 CONFIG – COM1 config error. The COM1 configuration settings do not
Config service req’d.
match backup configuration memory. The
G1000 system should be serviced
COM1 PTT – COM1 push-to-talk key The COM1 aexternal push-to-talk switch is
is stuck.
stuck in the enable (or “pressed”) position.
Press the PTT switch again to cycle its
operation.
If the problem persists, the G1000 system
should be serviced.
COM1 RMT XFR – COM1 remote
The COM1 transfer switch is stuck in the
transfer key is stuck.
enabled (or “pressed”) position. Press the
transfer switch again to cycle its operation.
If the problem persists, the G1000 system
should be serviced.
Flight
Instruments
Message Advisory
ARSPC AHEAD – Airspace ahead less
than 10 minutes.
Message Advisory
COM1 SERVICE – COM1 needs
service. Return unit for repair.
COM2 CONFIG – COM2 config error.
Config service req’d.
COM2 PTT – COM2 push-to-talk key
is stuck.
COM2 RMT XFR – COM2 remote
transfer key is stuck.
COM2 SERVICE – COM2 needs
service. Return unit for repair.
COM2 TEMP – COM2 over temp.
Reducing transmitter power.
DATA LOST – Pilot stored data was
lost. Recheck settings.
Index
Appendix
Annun/
Alerts
Abnormal
Operation
Additional
Features
Hazard
Avoidance
Procedures
Flight
Planning
AFCS
COM1 TEMP – COM1 over temp.
Reducing transmitter power.
GPS Nav
Nav/Com/
XPDR/Audio
EIS
Flight
Instruments
Annunciations & Alerts
128
Comments
The system has detected a failure in COM1.
COM1 may still be usable. The G1000 system
should be serviced when possible.
The system has detected an over temperature
condition in COM1. The transmitter operates
at reduced power. If the problem persists, the
G1000 system should be serviced.
The COM2 configuration settings do not
match backup configuration memory. The
G1000 system should be serviced
The COM2 external push-to-talk switch is
stuck in the enable (or “pressed”) position.
Press the PTT switch again to cycle its
operation.
If the problem persists, the G1000 system
should be serviced.
The COM2 transfer switch is stuck in the
enabled (or “pressed”) position. Press the
transfer switch again to cycle its operation.
If the problem persists, the G1000 system
should be serviced.
The system has detected a failure in COM2.
COM2 may still be usable. The G1000 system
should be serviced when possible.
The system has detected an over temperature
condition in COM2. The transmitter operates
at reduced power. If the problem persists, the
G1000 system should be serviced.
The pilot profile data was lost. System reverts
to default pilot profile and settings. The
pilot may reconfigure the MFD & PFD with
preferred settings, if desired.
Garmin G1000 Cockpit Reference Guide for the Diamond DA42NG
190-00963-04 Rev. A
Annunciations & Alerts
AFCS
GPS Nav
Flight
Planning
Procedures
Hazard
Avoidance
Additional
Features
DB MISMATCH – Obstacle database
mismatch.
Nav/Com/
XPDR/Audio
DB MISMATCH – Navigation
database mismatch. Xtalk is off.
EIS
DB CHANGE – Database changed.
Verify stored airways.
Abnormal
Operation
Annun/
Alerts
Comments
This occurs when a stored flight plan contains
procedures that have been manually edited.
This alert is issued only after an navigation
database update. Verify that the usermodified procedures in stored flight plans are
correct and up to date.
This occurs when a stored flight plan contains
an airway that is no longer consistent with
the navigation database. This alert is issued
only after an navigation database update.
Verify use of airways in stored flight plans and
reload airways as needed.
The PFD and MFD have different navigation
database versions or types installed. Crossfill
is off. Check the AUX-SYSTEM STATUS Page
to determine versions or regions. Also, check
the AUX-SYSTEM STATUS Page for a database
synchronization function not completed. After
synchronization is complete, power must be
turned off, then on.
The PFD and MFD have different obstacle
database versions or types installed. Check
the AUX-SYSTEM STATUS Page to determine
versions or regions. Also, check the AUXSYSTEM STATUS Page for a database
synchronization function not completed. After
synchronization is complete, power must be
turned off, then on.
Flight
Instruments
Message Advisory
DB CHANGE – Database changed.
Verify user modified procedures.
Appendix
Index
190-00963-04 Rev. A
Garmin G1000 Cockpit Reference Guide for the Diamond DA42NG
129
Message Advisory
Comments
DB MISMATCH – Standby Navigation The PFD and MFD have different standby
database mismatch.
navigation database versions or types
installed. Check the AUX-SYSTEM STATUS
Page to determine versions or regions.Also,
check the AUX-SYSTEM STATUS Page for
a database synchronization function not
completed. After synchronization is complete,
power must be turned off, then on.
DB MISMATCH – Terrain database
The PFD and MFD have different terrain
mismatch.
database versions or types installed. Check
the AUX-SYSTEM STATUS Page to determine
versions or regions. Also, check the AUXSYSTEM STATUS Page for a database
synchronization function not completed. After
synchronization is complete, power must be
turned off, then on.
FAILED PATH – A data path has
failed.
FPL TRUNC – Flight plan has been
truncated.
A data path connected to the GDU or the GIA
63W has failed.
This occurs when a newly installed navigation
database eliminates an obsolete approach
or arrival used by a stored flight plan. The
obsolete procedure is removed from the flight
plan. Update flight plan with current arrival
or approach.
Index
Appendix
Annun/
Alerts
Abnormal
Operation
Additional
Features
Hazard
Avoidance
Procedures
Flight
Planning
GPS Nav
AFCS
Nav/Com/
XPDR/Audio
EIS
Flight
Instruments
Annunciations & Alerts
130
Garmin G1000 Cockpit Reference Guide for the Diamond DA42NG
190-00963-04 Rev. A
Annunciations & Alerts
Hazard
Avoidance
Additional
Features
Abnormal
Operation
Annun/
Alerts
Appendix
Index
131
Procedures
Garmin G1000 Cockpit Reference Guide for the Diamond DA42NG
Flight
Planning
190-00963-04 Rev. A
GPS Nav
G/S2 SERVICE – G/S2 needs service.
Return unit for repair.
AFCS
G/S2 FAIL – G/S2 is inoperative.
Nav/Com/
XPDR/Audio
G/S1 SERVICE – G/S1 needs service.
Return unit for repair.
A failure has been detected in glideslope
receiver 1. The G1000 system should be
serviced.
A failure has been detected in glideslope
receiver 1. The receiver may still be available.
The G1000 system should be serviced when
possible.
A failure has been detected in glideslope
receiver 2. The G1000 system should be
serviced.
A failure has been detected in glideslope
receiver 2. The receiver may still be available.
The G1000 system should be serviced when
possible.
EIS
G/S1 FAIL – G/S1 is inoperative.
Flight
Instruments
Message Advisory
Comments
FPL WPT LOCK – Flight plan waypoint Upon power-up, the G1000 system detects
is locked.
that a stored flight plan waypoint is locked.
This occurs when an navigation database
update eliminates an obsolete waypoint. The
flight plan cannot find the specified waypoint
and flags this message. This can also occur
with user waypoints in a flight plan that is
deleted.
Remove the waypoint from the flight plan if it
no longer exists in any database,
OR
update the waypoint name/identifier to reflect
the new information.
FPL WPT MOVE – Flight plan
The system has detected that a waypoint
waypoint moved.
coordinate has changed due to a new
navigation database update. Verify that
stored flight plans contain correct waypoint
locations.
Message Advisory
GDC1 MANIFEST – GDC1 software
mismatch, communication halted.
GDL69 CONFIG – GDL 69 config
error. Config service req’d.
GDL69 FAIL – GDL 69 has failed.
GDL69 MANIFEST – GDL software
mismatch, communication halted.
GDL88 ADS-B 1090 - ADS-B fault.
1090 receiver failure.
GDL88 ADS-B NO POS - GDL88 is
not receiving position information.
GDL88 ADS-B NO TX - GDL88
Failure
GDL88 ADS-B TRFC - GDL 88 ADS-B
traffic has failed
GDL88 ADS-B UAT - ADS-B fault.
UAT receiver failure.
GDL88 ANTENNA - GDL 88 Antenna
fault
GDL88 CONFIG – GDL88 config error.
Index
Appendix
Annun/
Alerts
Abnormal
Operation
Additional
Features
Hazard
Avoidance
Procedures
Flight
Planning
GPS Nav
AFCS
Nav/Com/
XPDR/Audio
EIS
Flight
Instruments
Annunciations & Alerts
GDL88 CSA FAIL -- ADS-B Airborne
alerts failure.
GDL88 FAIL - Unable to transmit
ADS-B messages.
132
Comments
The GDC 74A has incorrect software installed.
The G1000 system should be serviced.
GDL 69/69A or GDL 69/69A SXM
configuration settings do not match those of
backup configuration memory. The G1000
system should be serviced.
A failure has been detected in the DL
69/69A or GDL 69/69A SXM. The receiver
is unavailable. The G1000 system should be
serviced.
The GDL 69/69A or GDL 69/69A SXM has
incorrect software installed. The G1000
system should be serviced.
A failure has been detected in the 1090
receiver.
The GDL 88 is not able to receive position
information.
Unable to transmit GDL 88 messages.
The GDL 88 is incapable of processing traffic
information.
A failure has been detected in the UAT
receiver.
The GDL 88 Antenna has failed.
The GDL 88 and GDU have incompatible
configurations. This alert is also set when
the GDL 88 has an invalid mode S address
configured or the mode S address does not
match both XPDR mode S addresses.
GDL 88 ADS-B Conflict Situational Awareness
(CSA) is unavailable.
The PFD has lost connection with the GDL 88.
Garmin G1000 Cockpit Reference Guide for the Diamond DA42NG
190-00963-04 Rev. A
Annunciations & Alerts
Appendix
Index
133
Annun/
Alerts
Garmin G1000 Cockpit Reference Guide for the Diamond DA42NG
Abnormal
Operation
190-00963-04 Rev. A
Additional
Features
GIA1 MANIFEST – GIA1 software
mismatch, communication halted.
Hazard
Avoidance
GIA1 COOLING – GIA1 over
temperature.
Procedures
GIA1 COOLING – GIA1 temperature
too low.
Flight
Planning
GIA1 CONFIG – GIA1 config error.
Config service req’d.
GPS Nav
GFC MANIFEST – GFC software
mismatch, communication halted.
GIA1 CONFIG – GIA1 audio config
error. Config service req’d.
The GDL 88 is not receiving transponder code.
The transponder should be in ALT mode when
airborne.
The GEA1 configuration settings do not
match those of backup configuration memory.
The G1000 system should be serviced.
The #1 GEA 71 has incorrect software
installed. The G1000 system should be
serviced.
The aircraft is outside geographical limits
for approved AHRS operation. Heading is
flagged as invalid.
Incorrect servo software is installed, or gain
settings are incorrect.
The GIA1 have an error in the audio
configuration. The G1000 system should be
serviced.
The GIA1 configuration settings do not match
backup configuration memory. The G1000
system should be serviced.
The GIA1 and/or GIA2 temperature is too low
to operate correctly. Allow units to warm up
to operating temperature.
The GIA1 temperature is too high. If problem
persists, the G1000 system should be
serviced.
The GIA1 1 has incorrect software installed.
The G1000 system should be serviced.
AFCS
GEO LIMITS – AHRS1 too far North/
South, no magnetic compass.
Return unit for repair.
Nav/Com/
XPDR/Audio
GEA1 MANIFEST – GEA1 software
mismatch, communication halted.
EIS
GEA1 CONFIG – GEA1 config error.
Config service req’d.
Comments
The GDL 88 is not receiving pressure altitude
data.
Flight
Instruments
Message Advisory
GDL88 PRES ALT - GDL88 is not
receiving pressure altitude.
GDL88 SERVICE – GDL88 needs
service.
GDL88 XPDR - GDL88 not receiving
XPDR code. Check XPDR mode.
Message Advisory
GIA1 SERVICE – GIA1 needs service.
Return the unit for repair.
Comments
The GIA1 self-test has detected a problem
in the unit. The G1000 system should be
serviced.
GIA2 CONFIG – GIA2 audio config
The GIA2 have an error in the audio
error. Config service req’d.
configuration. The G1000 system should be
serviced.
GIA2 CONFIG – GIA2 config error.
The GIA2 configuration settings do not match
Config service req’d.
backup configuration memory. The G1000
system should be serviced.
GIA2 COOLING – GIA2 over
The GIA2 temperature is too high. If problem
temperature.
persists, the G1000 system should be
serviced.
GIA2 COOLING – GIA2 temperature The GIA2 temperature is too low to operate
too low.
correctly. Allow units to warm up to
operating temperature.
GIA2 MANIFEST – GIA2 software
The GIA 2 has incorrect software installed.
mismatch, communication halted.
The G1000 system should be serviced.
GIA2 SERVICE – GIA2 needs service. The GIA2 self-test has detected a problem
Return the unit for repair.
in the unit. The G1000 system should be
serviced.
GMA1 CONFIG – GMA1 config error. The audio panel configuration settings do not
Config service req’d.
match backup configuration memory. The
G1000 system should be serviced.
GMA1 FAIL – GMA1 is inoperative.
The audio panel self-test has detected a
failure. The audio panel is unavailable. The
G1000 system should be serviced.
GMA1 MANIFEST – GMA1 software The audio panel has incorrect software inmismatch, communication halted.
stalled. The G1000 system should be serviced.
Index
Appendix
Annun/
Alerts
Abnormal
Operation
Additional
Features
Hazard
Avoidance
Procedures
Flight
Planning
GPS Nav
AFCS
Nav/Com/
XPDR/Audio
EIS
Flight
Instruments
Annunciations & Alerts
134
Garmin G1000 Cockpit Reference Guide for the Diamond DA42NG
190-00963-04 Rev. A
Annunciations & Alerts
GPS Nav
Flight
Planning
Procedures
Hazard
Avoidance
Additional
Features
Abnormal
Operation
Annun/
Alerts
Appendix
Index
135
AFCS
Garmin G1000 Cockpit Reference Guide for the Diamond DA42NG
Nav/Com/
XPDR/Audio
190-00963-04 Rev. A
EIS
Comments
The audio panel self-test has detected a
problem in the unit. Certain audio functions
may still be available, and the audio panel may
still be usable. The G1000 system should be
serviced when possible.
GMU1 MANIFEST – GMU1 software The GMU 44 has incorrect software installed.
mismatch, communication halted.
The G1000 system should be serviced.
GRA1 CAL – GRA1 calibration.
GRA1 has improper calibration. The system
Service req’d.
should be serviced.
GRA1 CONFIG – GRA1 config error. The GRA and GDU have incompatible
Config service req’d.
configurations.
GRA1 MANIFEST – GRA1 software
The GRA has incorrect software installed. The
mismatch, communication halted.
system should be serviced.
GRA1 SERVICE – GRA1 needs service. The GRA self-test has detected a problem in
Return unit for repair
the unit. The system should be serviced.
GRA1 TEMP – GRA1 over
The system has detected an over temperature
temperature.
condition in GRA1.
GPS NAV LOST – Loss of GPS
Loss of GPS navigation due to insufficient
navigation. Insufficient satellites.
satellites.
GPS NAV LOST – Loss of GPS
Loss of GPS navigation due to position error.
navigation. Position error.
GPS NAV LOST – Loss of GPS
Loss of GPS navigation due to GPS failure.
navigation. GPS fail.
GPS1 SERVICE – GPS1 needs service. A failure has been detected in the GPS1
Return unit for repair.
and/or GPS2 receiver. The receiver may still
GPS2 SERVICE – GPS2 needs service. be available. The G1000 system should be
serviced.
Return unit for repair.
GRS1 MANIFEST – GRS1 software
The #1 AHRS has incorrect software installed.
mismatch, communication halted.
The G1000 system should be serviced.
GSR1 FAIL – GSR1 has failed.
A failure has been detected in the GSR 56.
The transceiver is unavailable. The G1000
system should be serviced.
Flight
Instruments
Message Advisory
GMA1 SERVICE – GMA1 needs
service. Return unit for repair.
Message Advisory
GTX1 MANIFEST – GTX1 software
mismatch, communication halted.
GWX CONFIG – GWX config error.
Config service req’d.
GWX FAIL – GWX is inoperative.
GWX1 MANIFEST – GWX software
mismatch, communication halted.
GWX SERVICE – Needs service.
Return unit for repair.
HDG FAULT – AHRS1 magnetometer
fault has occurred.
HW MISMATCH – GIA hardware
mismatch. GIA1 communication
halted.
HW MISMATCH – GIA hardware
mismatch. GIA2 communication
halted.
INSIDE ARSPC – Inside airspace.
INVALID ADM – Invalid ADM: ATN
communication halted.
Index
Appendix
Annun/
Alerts
Abnormal
Operation
Additional
Features
Hazard
Avoidance
Procedures
Flight
Planning
GPS Nav
AFCS
Nav/Com/
XPDR/Audio
EIS
Flight
Instruments
Annunciations & Alerts
136
Comments
The transponder has incorrect software
installed. The G1000 system should be
serviced.
GWX 68/GWX 70 configuration settings do
not match those of the GDU configuration.
The G1000 system should be serviced.
The GDU is not recieving status packet from
the GWX 68/GWX 70 is reporting a fault. The
GWX 68/GWX 70 radar system should be
serviced.
The GWX 68/GWX 70 has incorrect software
installed. The G1000 system should be
serviced.
A failure has been detected in the GWX 68/
GWX 70. The GWX 68/GWX 70 may still be
usable.
A fault has occurred in the #1 GMU 44.
Heading is flagged as invalid. The AHRS uses
GPS for backup mode operation. The G1000
system should be serviced.
A GIA mismatch has been detected, where
only one is SBAS capable.
The aircraft is inside the airspace.
Data link avionics were not configured
correctly and therefore will not be able to
communicate with the ground network.
Garmin G1000 Cockpit Reference Guide for the Diamond DA42NG
190-00963-04 Rev. A
Annunciations & Alerts
Annun/
Alerts
Appendix
Index
137
Abnormal
Operation
Garmin G1000 Cockpit Reference Guide for the Diamond DA42NG
Additional
Features
The MFD configuration settings do not match
backup configuration memory. The G1000
system should be serviced.
The PFD and/or MFD is overheating and is
reducing power consumption by dimming
the display. If problem persists, the G1000
system should be serviced.
The MFD detected a failure in the Airport
Directory database. Ensure that the data
card is properly inserted. Replace data card.
If problem persists, the system should be
serviced.
The MFD detected a failure in the basemap
database.
Hazard
Avoidance
190-00963-04 Rev. A
Procedures
MFD1 DB ERR – MFD1 basemap
database error exists.
Flight
Planning
MFD1 DB ERR – MFD1 Airport
Directory database error exists.
GPS Nav
MFD1 COOLING – MFD1 has poor
cooling. Reducing power usage.
The PFD and/or MFD has incorrect software
installed. The G1000 system should be
serviced.
AFCS
MANIFEST – MFD1 software
mismatch, communication halted.
MANIFEST – PFD1 software
mismatch, communication halted.
MFD1 CONFIG – MFD1 config error.
Config service req’d.
Nav/Com/
XPDR/Audio
LOI – GPS integrity lost. Crosscheck
with other NAVS.
LRG MAG VAR – Verify all course
angles.
This occurs when the pilot attempts to
activate a stored flight plan that contains
locked waypoint. Remove locked waypoint
from flight plan. Update flight plan with
current waypoint.
GPS integrity is insufficient for the current
phase of flight.
The GDU’s internal model cannot determine
the exact magnetic variance for geographic
locations near the magnetic poles. Displayed
magnetic course angles may differ from the
actual magnetic heading by more than 2°.
EIS
LOCKED FPL – Cannot navigate
locked flight plan.
Comments
Flight
Instruments
Message Advisory
Message Advisory
MFD1 DB ERR – MFD1 Chartview
database error exists.
MFD1 DB ERR – MFD1 FliteCharts
database error exists.
MFD1 DB ERR – MFD1 multiple
database errors exists.
MFD1 DB ERR – MFD1 navigation
database error exists.
MFD1 DB ERR – MFD1 obstacle
database error exists.
MFD1 DB ERR – MFD1 obstacle
database missing.
MFD1 DB ERR – MFD1 Safe Taxi
database error exists.
MFD1 DB ERR – MFD1 terrain
database error exists.
Index
Appendix
Annun/
Alerts
Abnormal
Operation
Additional
Features
Hazard
Avoidance
Procedures
Flight
Planning
GPS Nav
AFCS
Nav/Com/
XPDR/Audio
EIS
Flight
Instruments
Annunciations & Alerts
138
Comments
The MFD detected a failure in the ChartView
database (optional feature). Ensure that the
data card is properly inserted. Replace data
card. If problem persists, the G1000 system
should be serviced.
The MFD detected a failure in the FliteCharts
database (optional feature). Ensure that the
data card is properly inserted. Replace data
card. If problem persists, the G1000 system
should be serviced.
The MFD detected a failure in more than one
database. If problem persists, the system
should be serviced.
The MFD detected a failure in the navigation
database. Attempt to reload the navigation
database. If problem persists, the G1000
system should be serviced.
The MFD detected a failure in the obstacle
database. Ensure that the data card is
properly inserted. Replace data card. If
problem persists, the G1000 system should be
serviced.
The obstacle database is present on another
LRU, but is missing on the specified LRU.
The MFD detected a failure in the Safe
Taxi database. Ensure that the data card
is properly inserted. Replace data card. If
problem persists, the G1000 system should be
serviced.
The MFD detected a failure in the terrain
database. Ensure that the terrain card is
properly inserted in display. Replace terrain
card. If problem persists, the G1000 system
should be serviced.
Garmin G1000 Cockpit Reference Guide for the Diamond DA42NG
190-00963-04 Rev. A
Annunciations & Alerts
GPS Nav
Flight
Planning
Procedures
Hazard
Avoidance
The remote NAV1 transfer switch is stuck in
the enabled (or “pressed”) state. Press the
transfer switch again to cycle its operation.
If the problem persists, the G1000 system
should be serviced.
NAV1 SERVICE – NAV1 needs service. A failure has been detected in the NAV1
Return unit for repair.
receiver. The receiver may still be available.
The G1000 system should be serviced.
NAV2 RMT XFR – NAV2 remote
The remote NAV2 transfer switch is stuck in
transfer key is stuck.
the enabled (or “pressed”) state. Press the
transfer switch again to cycle its operation.
If the problem persists, the G1000 system
should be serviced.
NAV2 SERVICE – NAV2 needs service. A failure has been detected in the NAV2
Return unit for repair.
receiver. The receiver may still be available.
The G1000 system should be serviced.
Additional
Features
Abnormal
Operation
Annun/
Alerts
Appendix
Index
Garmin G1000 Cockpit Reference Guide for the Diamond DA42NG
AFCS
NAV1 RMT XFR – NAV1 remote
transfer key is stuck.
190-00963-04 Rev. A
Nav/Com/
XPDR/Audio
MFD1 VOLTAGE – MFD1 has low
voltage. Reducing power usage
EIS
MFD1 DB ERR – MFD1 terrain
database missing.
MFD1 SERVICE – MFD1 needs
service. Return unit for repair.
MFD1 KEYSTK – MFD1 [key name]
is stuck.
Comments
The MFD detected a failure in the terrain
database. Ensure that the terrain card is
properly inserted in display. Replace terrain
card. If problem persists, the G1000 system
should be serviced.
The terrain database is present on another
LRU, but is missing on the specified LRU.
The MFD self-test has detected a problem.
The G1000 system should be serviced.
A key is stuck on the MFD bezel. Attempt to
free the stuck key by pressing it several times.
The G1000 system should be serviced if the
problem persists.
The MFD voltage is low. The G1000 system
should be serviced.
Flight
Instruments
Message Advisory
MFD1 DB ERR – MFD1 terrain
database error exists.
139
Message Advisory
NON WGS84 WPT – Do not use GPS
for navigation to [xxxx]
Comments
The position of the selected waypoint [xxxx]
is not calculated based on the WGS84 map
reference datum and may be positioned
in error as displayed. Do not use GPS
to navigate to the selected non-WGS84
waypoint..
PFD1 DB ERR – PFD1 basemap
database error exists.
PFD1 DB ERR – PFD1 multiple
database errors exists.
The PFD detected a failure in the basemap
database.
The PFD detected a failure in more than one
database. If problem persists, the system
should be serviced.
The PFD detected a failure in the navigation
database. Attempt to reload the navigation
database. If problem persists, the G1000
system should be serviced.
The obstacle database is present on another
LRU, but is missing on the specified LRU.
The PFD detected a failure in the Safe Taxi
database. Ensure that the data card is
properly inserted. Replace data card. If
problem persists, the G1000 system should be
serviced.
The PFD detected a failure in the terrain
database. Ensure that the terrain card is
properly inserted in display. Replace terrain
card. If problem persists, the G1000 system
should be serviced.
The terrain database is present on another
LRU, but is missing on the specified LRU.
The PFD configuration settings do not match
backup configuration memory. The G1000
system should be serviced.
PFD1 DB ERR – PFD1
navigation database error exists.
PFD1 DB ERR – PFD1 obstacle
database missing.
PFD1 DB ERR – PFD1 Safe Taxi
database error exists.
PFD1 DB ERR – PFD1 terrain
database error exists.
Index
Appendix
Annun/
Alerts
Abnormal
Operation
Additional
Features
Hazard
Avoidance
Procedures
Flight
Planning
GPS Nav
AFCS
Nav/Com/
XPDR/Audio
EIS
Flight
Instruments
Annunciations & Alerts
PFD1 DB ERR – PFD1 terrain
database missing.
PFD1 CONFIG – PFD1 config error.
Config service req’d.
140
Garmin G1000 Cockpit Reference Guide for the Diamond DA42NG
190-00963-04 Rev. A
Annunciations & Alerts
GPS Nav
Flight
Planning
Procedures
Hazard
Avoidance
Additional
Features
Abnormal
Operation
Annun/
Alerts
Appendix
Index
Stormscope has failed. The G1000 System
should be serviced.
Message criteria entered by the user.
Garmin G1000 Cockpit Reference Guide for the Diamond DA42NG
AFCS
190-00963-04 Rev. A
Nav/Com/
XPDR/Audio
STRMSCP FAIL – Stormscope has
failed.
SCHEDULER [#] – <message>.
EIS
Comments
The PFD is overheating and is reducing power
consumption by dimming the display. If
problem persists, the G1000 system should be
serviced.
PFD1 KEYSTK – PFD1 [key name] is A key is stuck on the PFD bezel. Attempt to
stuck.
free the stuck key by pressing it several times.
The G1000 system should be serviced if the
problem persists.
[PFD1 or MFD1] CARD 1 REM –
The SD card was removed from the top card
Card 1 was removed. Reinsert card. slot of the specified PFD or MFD. The SD card
needs to be reinserted.
[PFD1 or MFD1] CARD 2 REM –
The SD card was removed from the bottom
Card 2 was removed. Reinsert card. card slot of the specified PFD or MFD. The SD
card needs to be reinserted.
[PFD1 or MFD1] CARD 1 ERR – Card The SD card in the top card slot of the
1 is invalid.
specified PFD or MFD contains invalid data.
[PFD1 or MFD1] CARD 2 ERR – Card The SD card in the bottom card slot of the
2 is invalid.
specified PFD or MFD contains invalid data.
PFD1 SERVICE – PFD1 needs service. The PFD self-test has detected a problem. The
Return unit for repair.
G1000 system should be serviced.
PFD1 VOLTAGE – PFD1 has low
The PFD1 voltage is low. The G1000 system
voltage. Reducing power usage
should be serviced.
PTK FAIL – Parallel track unavailable:
Invalid leg type for parallel offset.
invalid leg type.
PTK FAIL – Parallel track unavailable: IAF waypoint for parallel offset has been
past IAF.
passed.
PTK FAIL – Parallel track unavailable:
Bad parallel track geometry.
bad geometry.
Flight
Instruments
Message Advisory
PFD1 COOLING – PFD1 has poor
cooling. Reducing power usage.
141
Message Advisory
SLCT FREQ – Select appropriate
frequency for approach.
Comments
The system notifies the pilot to load the
approach frequency for the appropriate NAV
receiver. Select the correct frequency for the
approach.
SLCT MAG– Select MAGNETIC NAV
The system notifies the pilot to set the Nav
ANGLE display units.
Angle units on the Avioncs Settings Screen to
Magnetic.
SLCT NAV – Select NAV on CDI for
The system notifies the pilot to set the CDI to
approach.
the correct NAV receiver. Set the CDI to the
correct NAV receiver.
SLCT NON-MAG– Select alternate
The system notifies the pilot to set the Nav
NAV ANGLE display units.
Angle units on the Avioncs Settings Screen to
True.
STEEP TURN – Steep turn ahead.
A steep turn is 15 seconds ahead. Prepare
to turn.
SVS – SVS DISABLED: Out of available Synthetic Vision is disabled because the
terrain region.
aircraft is not within the boundaries of the
installed terrain database.
SVS – SVS DISABLED: Terrain DB
Synthetic Vision is disabled because a terrain
resolution too low.
database of sufficient resolution (9 arcsecond or better) is not currently installed.
SW MISMATCH – GDU software
The MFD and PFD have different software
version mismatch. Xtalk is off.
versions installed. The G1000 system should
be serviced.
TIMER EXPIRD – Timer has expired.
TRAFFIC FAIL – Traffic device has
failed.
The system notifies the pilot that the timer
has expired.
The G1000 is no longer receiving data from
the traffic system. The traffic device should be
serviced.
Index
Appendix
Annun/
Alerts
Abnormal
Operation
Additional
Features
Hazard
Avoidance
Procedures
Flight
Planning
GPS Nav
AFCS
Nav/Com/
XPDR/Audio
EIS
Flight
Instruments
Annunciations & Alerts
142
Garmin G1000 Cockpit Reference Guide for the Diamond DA42NG
190-00963-04 Rev. A
Annunciations & Alerts
Comments
Flight
Instruments
Message Advisory
Flight
Planning
Procedures
Hazard
Avoidance
Arriving at waypoint [xxxx], where [xxxx] is
the waypoint name.
The GWX 68/GWX 70 indicates severe
weather within ±10 degrees of the aircraft
heading at a range of 80 to 320 nm.
Additional
Features
Abnormal
Operation
WPT ARRIVAL – Arriving at waypoint
-[xxxx]
WX ALERT – Possible severe weather
ahead.
GPS Nav
VNV – Unavailable. Parallel course
selected.
The lateral flight plan contains a procedure
turn, vector, or other unsupported leg type
prior to the active vertical waypoint. This
prevents vertical guidance to the active
vertical waypoint.
The current crosstrack exceeds the limit,
causing vertical deviation to go invalid.
The current track angle error exceeds the
limit, causing the vertical deviation to go
invalid.
A parallel course has been selected, causing
the vertical deviation to go invalid.
AFCS
VNV – Unavailable. Excessive
crosstrack error.
VNV – Unavailable. Excessive track
angle error.
Nav/Com/
XPDR/Audio
VNV – Unavailable. Unsupported leg
type in flight plan.
EIS
UNABLE V WPT – Can’t reach current The current vertical waypoint can not be
vertical waypoint.
reached within the maximum flight path
angle and vertical speed constraints. The
system automatically transitions to the next
vertical waypoint.
Garmin G1000 Cockpit Reference Guide for the Diamond DA42NG
143
Index
190-00963-04 Rev. A
Appendix
ADS-B is inoperative. Other transponder
functions may be available. Transponder
should be serviced when possible. (GTX 33
with Extended Squitter only.)
XPDR1 CONFIG – XPDR1 config error. The transponder configuration settings do not
Config service req’d.
match those of backup configuration memory.
The G1000 system should be serviced.
Annun/
Alerts
XPDR1 ADS-B FAIL – XPDR1 unable
to transmit ADS-B messages.
Message Advisory
XPDR1 SRVC – XPDR1 needs service.
Return unit for repair.
XPDR1 FAIL – XPDR1 is inoperative.
XTALK ERROR – A flight display
crosstalk error has occurred.
Comments
The #1 transponder should be serviced when
possible.
There is no communication with the #1
transponder.
The MFD and PFD are not communicating
with each other. The G1000 system should be
serviced.
AFCS
Nav/Com/
XPDR/Audio
EIS
Flight
Instruments
Annunciations & Alerts
Index
Appendix
Annun/
Alerts
Abnormal
Operation
Additional
Features
Hazard
Avoidance
Procedures
Flight
Planning
GPS Nav
FLIGHT PLAN IMPORT/EXPORT MESSAGES
In some circumstances, some messages may appear in conjunction with others.
Flight Plan Import/Export Results
‘Flight plan successfully imported.’
Description
A flight plan file stored on the SD card was
successfully imported as a stored flight
plan.
‘File contained user waypoints only.
The file stored on the SD card did not
User waypoints imported successfully.
contain a flight plan, only user waypoints.
No stored flight plan data was modified.’ These waypoints have been saved to the
system user waypoints. No flight plans
stored in the system have been modified.
‘No flight plan files found to import.’
The SD card contains no flight plan data.
‘Flight plan import failed.’
Flight plan data was not successfully
imported from the SD card.
‘Flight plan partially imported.’
Some flight plan waypoints were
successfully imported from the SD card,
however others had errors and were not
imported. A partial stored flight plan now
exists in the system.
‘File contained user waypoints only.’
The file stored on the SD card did not
contain a flight plan, only user waypoints.
One or more of these waypoints did not
import successfully.
144
Garmin G1000 Cockpit Reference Guide for the Diamond DA42NG
190-00963-04 Rev. A
Annunciations & Alerts
Flight
Instruments
EIS
Nav/Com/
XPDR/Audio
AFCS
GPS Nav
Flight
Planning
Procedures
Hazard
Avoidance
Additional
Features
Abnormal
Operation
Annun/
Alerts
Flight Plan Import/Export Results
Description
‘Too many points. Flight plan truncated.’ The flight plan on the SD card contains
more waypoints than the system can
support. The flight plan was imported with
as many waypoints as possible.
‘Some waypoints not loaded. Waypoints The flight plan on the SD card contains one
locked.’
or more waypoints that the system cannot
find in the navigation database. The flight
plan has been imported, but must be edited
within the system before it can be activated
for use.
‘User waypoint database full. Not all
The flight plan file on the SD card contains
loaded.’
user waypoints. The quantity of stored user
waypoints has exceeded system capacity,
therefore not all the user waypoints on the
SD card have been imported. Any flight
plan user waypoints that were not imported
are locked in the flight plan. The flight plan
must be edited within the system before it
can be activated for use.
‘One or more user waypoints renamed.’ One or more imported user waypoints were
renamed when imported due to naming
conflicts with waypoints already existing in
the system.
‘Flight plan successfully exported.’
The stored flight plan was successfully
exported to the SD card.
‘Flight plan export failed.’
The stored flight plan was not successfully
exported to the SD card. The SD card may
not have sufficient available memory or the
card may have been removed prematurely.
Appendix
Index
190-00963-04 Rev. A
Garmin G1000 Cockpit Reference Guide for the Diamond DA42NG
145
Index
Appendix
Annun/
Alerts
Abnormal
Operation
Additional
Features
Hazard
Avoidance
Procedures
Flight
Planning
GPS Nav
AFCS
Nav/Com/
XPDR/Audio
EIS
Flight
Instruments
Annunciations & Alerts
Blank Page
146
Garmin G1000 Cockpit Reference Guide for the Diamond DA42NG
190-00963-04 Rev. A
Appendix
Flight
Instruments
APPENDIX
PFD SOFTKEY MAP
EIS
ADF/DME
ALERTS
Nav/Com/
XPDR/Audio
AFCS
GPS Nav
Top Level PFD Softkeys
(optional)
ADF/DME
(optional)
PRECIP
or
DL LTNG
or
TRFC-1
METAR
ALERTS
Additional
Features
Inset Map Softkeys
OFF
Abnormal
Operation
Displays Inset Map in PFD lower left corner
INSET
Removes Inset Map
Index
147
Appendix
Garmin G1000 Cockpit Reference Guide for the Diamond DA42NG
Annun/
Alerts
DCLTR (3) Selects desired amount of map detail; cycles through
declutter levels:
DCLTR (No Declutter): All map features visible
DCLTR-1: Declutters land data
DCLTR-2: Declutters land and SUA data
DCLTR-3: Removes everything except the active
flight plan
WX LGND Displays icon and age on the Inset Map for the
selected weather products (optional)
190-00963-04 Rev. A
Hazard
Avoidance
Press the BACK Softkey to return to
the top-level softkeys.
TRFC-2
Procedures
STRMSCP
(optional)
Flight
Planning
WX LGND
ALERTS
Appendix
EIS
Flight
Instruments
TRAFFIC
Nav/Com/
XPDR/Audio
TOPO
TERRAIN
Cycles through traffic display options:
TRFC-1: Traffic displayed on inset map
TRFC-2: Traffic Map Page is displayed in the inset
map window
Displays topographical data (e.g., coastlines, terrain,
rivers, lakes) and elevation scale on Inset Map
Displays terrain information on Inset Map
GPS Nav
AFCS
STRMSCP Select to display the optional Stormscope lightning
data on the Inset Map (within a 200 nm radius of
the aircraft)
NEXRAD Displays NEXRAD weather and coverage
information on the Inset Map (optional)
or
Flight
Planning
PRECIP
XM LTNG
Procedures
or
Hazard
Avoidance
DL LTNG
Displays Worldwide Weather lightning information
on the Inset Map (optional)
Displays METAR flags on airport symbols shown on
the Inset Map (optional)
Index
Appendix
Annun/
Alerts
Abnormal
Operation
Additional
Features
METAR
Displays Worldwide Weather precipitation on the
Inset Map (optional)
Displays XM lightning information on the Inset Map
(optional)
148
Garmin G1000 Cockpit Reference Guide for the Diamond DA42NG
190-00963-04 Rev. A
Appendix
ADF/DME
ALERTS
ALT UNIT
HSI FMT
Flight
Instruments
SYN VIS
ALERTS
EIS
Select the BACK Softkey
to return to the top-level softkeys
Nav/Com/
XPDR/Audio
IN
HPA
ALERTS
ALERTS
GPS Nav
METERS
BACK
ARC HSI
AFCS
360 HSI
ALERTS
SYN TERR HRZN HDG APTSIGNS
ALERTS
Procedures
PFD Configuration Softkeys
Garmin G1000 Cockpit Reference Guide for the Diamond DA42NG
149
Index
190-00963-04 Rev. A
Appendix
HRZN HDG Displays compass heading along the
Zero-Pitch line
APTSIGNS Displays position markers for airports
within approximately 15 nm of the
current aircraft position. Airport
identifiers are displayed when the
airport is within approximately 9 nm.
Annun/
Alerts
SYN TERR
Abnormal
Operation
PATHWAY
Additional
Features
SYN VIS
Displays second-level softkeys for
additional PFD configurations
Displays the softkeys for enabling or
disabling Synthetic Vision features
Displays rectangular boxes representing
the horizontal and vertical flight path
of the active flight plan
Enables synthetic terrain depiction
Hazard
Avoidance
PFD
Flight
Planning
PATHWAY
Appendix
Flight
Instruments
DFLTS
EIS
WIND
Nav/Com/
XPDR/Audio
OPTN 1
OPTN 2
AFCS
OPTN 3
OFF
Wind direction arrow with headwind/
tailwind and crosswind components
Information not displayed
Displays the DME Information Window
Cycles the Bearing 1 Information
Window through NAV1 or GPS/
waypoint identifier and GPS-derived
distance information, and ADF/
DME
BRG1
Flight
Planning
GPS Nav
Resets PFD to default settings,
including changing units to standard
Displays softkeys to select wind data
parameters
Wind direction arrows with headwind
and crosswind components
Wind direction arrow and speed
Procedures
frequency.
HSI FRMT
Hazard
Avoidance
360 HSI
ARC HSI
Additional
Features
BRG2
Displays the HSI formatting softkeys
Displays the HSI in a 360 degree format
Displays the HSI in an arc format
Cycles the Bearing 2 Information Window
through NAV2 or GPS/waypoint identifier
and GPS-derived distance information,
and ADF/frequency.
Displays softkeys for setting the altimeter
and BARO settings to metric units
Appendix
Annun/
Alerts
Abnormal
Operation
ALT UNIT
Index
STD BARO
150
METERS
When enabled, displays altimeter in
meters
IN
Press to display the BARO setting as
inches of mercury
HPA
Press to display the BARO setting as
hectopacals
Sets barometric pressure to 29.92 in
Hg (1013 hPa)
Garmin G1000 Cockpit Reference Guide for the Diamond DA42NG
190-00963-04 Rev. A
Appendix
ALERTS
ADS-B TX
Flight
Instruments
ADF/DME
ALERTS
EIS
ALERTS
GPS Nav
Transponder Softkeys
STBY
Automatically enters the VFR code (1200
in the U.S.A. only)
Index
Garmin G1000 Cockpit Reference Guide for the Diamond DA42NG
151
Appendix
Green (Airborne) - Transponder generates
Mode A, Mode C, and Mode S replies to
interrogations, as well as transmissions of
acquisition and extended squitters including ADS-B out.
Annun/
Alerts
190-00963-04 Rev. A
Abnormal
Operation
VFR
Additional
Features
White (On-Ground) - Transponder does
not allow Mode A and Mode C replies, but
it does permit acquisition and extended
squitters including ADS-B out, and replies
to discretely addressed Mode S interrogations.
Hazard
Avoidance
ALT
Procedures
ON
Selects Standby Mode (transponder does
not reply to any interrogations)
Selects Mode A (transponder replies to
interrogations)
Selects Altitude Mode (selection is usually
automatic)
Flight
Planning
Displays transponder mode selection softkeys
XPDR
AFCS
Press the BACK Softkey to return
to the previous level softkeys.
Nav/Com/
XPDR/Audio
Press the BACK Softkey to return
to the top-level softkeys.
Appendix
0—7
Displays transponder code selection
softkeys 0-7
Use numbers to enter code
BKSP
Removes numbers entered, one at a time
EIS
Flight
Instruments
CODE
TMR/REF
Activates the Special Position Identification
(SPI) pulse for 18 seconds, identifying the
transponder return on the ATC screen
Activates/deactivates transmission of the
aircraft’s three-dimensional position and
aircraft heading for reception by ADS-B
systems.
Displays Timer/References Window
NRST
Displays Nearest Airports Window
ALERTS
Displays Alerts Window
Nav/Com/
XPDR/Audio
IDENT
MFD SOFTKEY MAP
Procedures
Flight
Planning
GPS Nav
AFCS
ADS-B TX
DCLTR
MAP
ENGINE
SHW CHRT
CHKLIST
(optional)
(optional)
Hazard
Avoidance
DCLTR-1
DCLTR-2
DCLTR-3
Additional
Features
(Default softkey
is dependant on
the selection made
in the map setup
options)
PROFILE
TOPO
Abnormal
Operation
TRAFFIC
TERRAIN
AIRWAYS
(optional)
STRMSCP
(optional)
(optional)
PRECIP
or
(optional)
NEXRAD
DL LTNG
or
(optional)
XM LTNG
Press the BACK Softkey on this
level to return to the top softkey level.
(optional)
METAR
(optional)
LEGEND
BACK
AIRWY ON
AIRWY LO
Annun/
Alerts
AIRWAY HI
ENGINE
SYSTEM
LEAN
DEC FUEL
INC FUEL
RST FUEL
The CHECK Softkey changes to UNCHECK when the checklist
item is already checked
Appendix
CHECK
RETURN
EXIT
EMERGCY
Index
MFD Softkeys
152
Garmin G1000 Cockpit Reference Guide for the Diamond DA42NG
190-00963-04 Rev. A
Appendix
SYSTEM
Displays the Engine System Display
FUEL
Displays the fuel softkeys
Flight
Instruments
Displays EIS-Engine Page
ENGINE
Additional
Features
Abnormal
Operation
Annun/
Alerts
STRMSCP
Hazard
Avoidance
AIRWAYS
Procedures
TERRAIN
Flight
Planning
TOPO
GPS Nav
PROFILE
Appendix
Enables second-level Navigation Map
softkeys
Displays traffic information on
Navigation Map
Displays/removes Profile View on
Navigation Map Page
Displays topographical data (e.g.,
coastlines, terrain, rivers, lakes) and
elevation scale on Navigation Map
Displays terrain information on
Navigation Map
Displays airways on the map; cycles
through the following:
AIRWAYS: No airways are displayed
AIRWY ON: All airways are
displayed
AIRWY LO: Only low altitude
airways are displayed
AIRWY HI: Only high altitude
airways are displayed
Displays Stormscope weather and
coverage information on Navigation
Map (optional)
AFCS
TRAFFIC
Nav/Com/
XPDR/Audio
MAP
EIS
DEC FUEL Press to decrease remaining fuel
quantity in 1-gallon increments
INC FUEL Press to increase remaining fuel
quantity in 1-gallon increments
RST FUEL Press to reset fuel to full
Index
190-00963-04 Rev. A
Garmin G1000 Cockpit Reference Guide for the Diamond DA42NG
153
Appendix
Flight
Instruments
NEXRAD
or
Nav/Com/
XPDR/Audio
EIS
PRECIP
XM LTNG
or
GPS Nav
AFCS
DL LTNG
Flight
Planning
METAR
BACK
DCLTR (3)
SHW CHRT
CHKLIST
Displays Worldwide Weather precipitation on the Navigation Map (optional)
Displays XM lightning information on
the Navigation Map (optional)
Displays Worldwide Weather lightning
information on the Navigation Map
(optional)
Displays METAR flags on airport
symbols shown on the Inset Map
(optional)
Displays the legend for the selected
weather products. Available only when
NEXRAD, XM LTNG, and/or METAR
softkeys are selected.
Returns to top-level softkeys
Selects desired amount of map detail;
cycles through declutter levels:
DCLTR (No Declutter): All map
features visible
DCLTR-1: Declutters land data
DCLTR-2: Declutters land and SUA
data
DCLTR-3: Removes everything
except the active flight plan
When available, displays optional
airport and terminal procedure charts
When available, displays optional
checklists
Index
Appendix
Annun/
Alerts
Abnormal
Operation
Additional
Features
Hazard
Avoidance
Procedures
LEGEND
Displays NEXRAD weather and
coverage information on the
Navigation Map (optional)
154
Garmin G1000 Cockpit Reference Guide for the Diamond DA42NG
190-00963-04 Rev. A
Appendix
GPS Nav
Flight
Planning
Procedures
Hazard
Avoidance
Additional
Features
Error Message
Description
Canceled
Database synchronization has been canceled by removing the
bottom SD card in display being updated
Card Full
SD card does not contain sufficient memory
Err
Displayed for all other errors that may cause the synchronization
process to be halted
Timeout
System timed-out prior to the database transfer completing
AFCS
In some cases it may be necessary to obtain an unlock code from Garmin in order
to make the database product functional. It may also be necessary to have the system
configured by a Garmin authorized service facility in order to use some database features.
If an error occurs during synchronization, an error message will be displayed,
followed by the affected display in the Sync Status section of the Database Window. If
synchronization completes on one display, but an error occurs on another, the error
message will be displayed with the affected displays listed after it. When an error
message is displayed, the problem must be corrected before synchronization can be
completed. A power cycle is required to restart synchronization when ‘Card Full’ or
‘Err’ is shown.
Nav/Com/
XPDR/Audio
NOTE: Garmin requests that the flight crew report any observed discrepancies
related to database information. These discrepancies could come in the form
of an incorrect procedure; incorrectly identified terrain, obstacles and fixes; or
any other displayed item used for navigation or communication in the air or
on the ground. Go to FlyGarmin.com and select “Aviation Data Error Report.
EIS
CAUTION: Never disconnect power to the system when loading a database.
Power interruption during the database loading process could result in maintenance being required to reboot the system.
Flight
Instruments
LOADING UPDATED DATABASES
Abnormal
Operation
Annun/
Alerts
Appendix
Index
190-00963-04 Rev. A
Garmin G1000 Cockpit Reference Guide for the Diamond DA42NG
155
Updating the active navigation database (not using the Dual
Navigation Database or Automatic Database Synchronization
Features):
Go to www.flygarmin.com or www.jeppesen.com. Download the
applicable software and install the navigation database on a blank
SD card.
2) With the system OFF, insert the SD card containing the new navigation database
version into the top card slot of the display (label of SD card facing left).
1)
GPS Nav
AFCS
Nav/Com/
XPDR/Audio
EIS
Flight
Instruments
Appendix
4)
5)
Press the NO Softkey to proceed to loading only the active database.
A prompt similar to the following is displayed, press the YES Softkey to
update the active navigation database.
After the update completes, the display starts in normal mode. Do not
remove power while the display is starting.
Hazard
Avoidance
Procedures
Flight
Planning
6)
7)
Turn the system OFF and remove the SD card from the top card slot.
8)
Repeat steps 2 through 7 for the other display. Remove the SD card when
finished.
9)
Apply power to the system and press the ENT Key or the right-most softkey on
the MFD to acknowledge the startup screen.
10) Turn the large FMS Knob to select the AUX Page group on the MFD.
Additional
Features
11) Turn the small FMS Knob to select the System Status Page.
12) Press the Display Database Selection Softkey to show active navigation
database information for each display.
13) Verify the correct navigation database cycle information is shown for each
display.
Abnormal
Operation
Annun/
Alerts
Turn the system ON. A prompt similar to the following is displayed in the
upper left corner of the display:
Dual Navigation Database Feature
The dual navigation database feature allows each display to store an upcoming
navigation database on the bottom SD card so that the system can automatically
load it to replace the active database when the new database becomes effective
(the next cycle becomes available seven days prior to its effective date).
Index
Appendix
3)
156
Garmin G1000 Cockpit Reference Guide for the Diamond DA42NG
190-00963-04 Rev. A
Appendix
Flight
Instruments
EIS
Nav/Com/
XPDR/Audio
The system checks the active and standby databases upon (on-ground only) powerup. If the standby database is current and the active database is out of date, the display
will upload the standby database into the active internal database location. Loading
the standby database to the active location takes approximately 45-55 seconds. During the loading process ‘Please Wait. Navigation Database Update in Progress. Do Not
Remove Power from Displays’ will be displayed on screen. After startup is complete,
the pilot is alerted that the update is complete by a system alert message, ‘NAV DB
UPDATED’.
Loading a standby navigation database:
AFCS
Go to www.flygarmin.com or www.jeppesen.com. Download the
applicable software and install the navigation database on a blank
SD card.
2)
With the system OFF, insert the SD card containing the new navigation
database version into the top card slot of the display.
3)
Verify that an SD card is inserted in the bottom slot of each display.
4)
Turn the system ON. A prompt similar to the following is displayed.
5)
Press the YES softkey. The navigation database is copied to the SD card in
the bottom of the display.
6)
7)
8)
As instructed on the display, press any key to continue.
Press any key to continue.
Press the NO Softkey. The display now starts in normal mode. Since the
database effective date is not yet valid, it should not be loaded as the
active database. The display now starts in normal mode. Do not remove
power while the display is starting.
GPS Nav
1)
Flight
Planning
Hazard
Avoidance
Additional
Features
Abnormal
Operation
Annun/
Alerts
Appendix
12) Turn the large FMS Knob to select the AUX Page group on the MFD.
13) Turn the small FMS Knob to select the System Status Page.
Garmin G1000 Cockpit Reference Guide for the Diamond DA42NG
Index
14) Press the Display Database Selection Softkey to show standby navigation
database information for each display.
190-00963-04 Rev. A
Procedures
Turn the system OFF and remove the SD card from the top card slot.
10) Repeat steps 2 through 10 for the other display.
11) Apply power to the system and press the ENT Key on the MFD display to
acknowledge the startup screen.
9)
157
Appendix
16) Remove power from the system.
Updating Basemap, SafeTaxi, Obstacle, Airport Directory, Chartview
and Flitecharts Databases
AFCS
Nav/Com/
XPDR/Audio
EIS
Flight
Instruments
15) Verify the correct standby navigation database cycle information is shown
for each display.
1)
With the system OFF, remove the Garmin SD Cards from the bottom SD card slot of
each flight display unit.
2)
Go to www.flygarmin.com. Download the applicable software and
install the databases on the Garmin SD card for each display. (The
Additional
Features
Hazard
Avoidance
Procedures
Flight
Planning
GPS Nav
FliteChart database must only be installed on the MFD SD Card).
3)
Put the Garmin SD Cards back in the bottom SD card slots of each flight
display unit.
4)
Turn the system ON.
5)
During MFD power-up, check the MFD Power-Up screen and make sure that
the database is initialized and shown on the database information.
6)
Press the ENT Key on MFD display to acknowledge the startup screen.
7)
Turn the large FMS Knob to select the AUX Page group on the MFD.
8)
Turn the small FMS Knob to select the System Status Page.
9)
Press the Display Database Selection Softkey to show database information
for each display.
10) Verify the correct database cycle information is shown for each display.
Index
Appendix
Annun/
Alerts
Abnormal
Operation
11) Remove power from the system.
158
Garmin G1000 Cockpit Reference Guide for the Diamond DA42NG
190-00963-04 Rev. A
Appendix
EIS
At startup, the system compares this version of the MV DB with that presently being
used by the AHRS (GRS). If the system determines the MV DB needs to be updated,
a prompt is displayed on the Navigation Map Page, as shown in the following figure.
Flight
Instruments
Magnetic Field Variation Database Update
Nav/Com/
XPDR/Audio
AFCS
GRS Magnetic Field Variation Database Update Prompt
GPS Nav
Flight
Planning
Loading the magnetic field variation database update:
With ‘OK’ highlighted, as shown in the previous figure, press the ENT Key
on the MFD. A progress monitor is displayed as shown in the following
figure.
Procedures
Hazard
Avoidance
Additional
Features
Abnormal
Operation
Uploading Database to GRS
Annun/
Alerts
Appendix
Index
190-00963-04 Rev. A
Garmin G1000 Cockpit Reference Guide for the Diamond DA42NG
159
Index
Appendix
Annun/
Alerts
Abnormal
Operation
Additional
Features
Hazard
Avoidance
Procedures
Flight
Planning
GPS Nav
AFCS
Nav/Com/
XPDR/Audio
EIS
Flight
Instruments
Appendix
Blank Page
160
Garmin G1000 Cockpit Reference Guide for the Diamond DA42NG
190-00963-04 Rev. A
Index
Annun/
Alerts
Gain 68
Garmin Connext 47, 48, 53, 54
Garmin Connext Weather 49
Appendix
H
Index
Horizon heading 79
Horizontal Scan 68
I
Garmin G1000 Cockpit Reference Guide for the Diamond DA42NG
Abnormal
Operation
G
Additional
Features
190-00963-04 Rev. A
Flight Director 13
Flight ID 9
Flight path marker 79
Flight plan import/export messages 144
FliteCharts® 80, 81
Frequency Transfer 10
Fuel remaining 7
Fuel used 7
Hazard
Avoidance
CDI 1, 10
Cell 43, 44
Cell mode 44
Channel Presets 84
ChartView 80, 81
Checklists 106–107
CLD TOP Softkey 56
Clearance player 11
Clearance Recorder 11
Code selection softkeys 10
COM 10, 11, 109
F
Procedures
C
Edit a flight plan 33
Electronic checklists 107, 108
Emergency checklist 107
Enable Terrain 77
Endurance 7
ESP™ 98
Flight
Planning
Barometric Altitude Minimums 3
Barometric pressure 150
Bearing Line 68, 69
E
GPS Nav
B
AFCS
Database Synchronization 156
DCLTR Softkey 80
Dead Reckoning 110
Declutter 110, 147, 154
Direct-to 17
DME 9, 10
DR mode 110, 111, 112
Dual navigation database 156
Nav/Com/
XPDR/Audio
Access Code 48
Activate a flight plan 18
Active Channel 83
Active database 156, 157
AC-U-KWIK® 82
ADF 9, 10, 110, 150
ADS-B 152
Advisory alerts 115
AHRS 126, 133, 136
AIRMET 57
Airport Directory 82
Airport Signs 79, 80
Airways 153
Antenna Stabilization 70
Antenna Tilt 67
AOPA Airport Directory 82
Audio panel controls
NAV1, NAV2 10
Auxiliary video 100
EIS
D
Flight
Instruments
A
Index-1
Index
Appendix
Annun/
Alerts
Abnormal
Operation
Additional
Features
Hazard
Avoidance
Procedures
Flight
Planning
GPS Nav
AFCS
Nav/Com/
XPDR/Audio
EIS
Flight
Instruments
Index
Inhibit Terrain 77
Inset Map 147, 148
IOI 120
Iridium 85, 88
J
Jeppesen 81
L
Lightning 43, 44, 49, 148
M
Map panning 45
Message advisories 126
Messages window 102
METAR 45, 49, 57, 58, 148
MKR/MUTE 11
Mode selection softkeys 10
Multi Function Display (MFD)
Softkeys 152
N
NAV 10
NAV1 1, 10
NAV2 1, 10
Navigation database 19, 20
NEXRAD 45, 148, 153, 154
NEXRAD Softkey 55
O
OBS 2
Obstacles 129, 136
Overspeed Protection 14
P
Pathways 79, 80
Pilot Weather Report (PIREP) 49
PIREP 58
Index-2
Power-up page 106
Precipitation 49
Predefined Message 91
R
Register 48
Reversionary mode 109
ROC 120
S
SafeTaxi® 80
SBAS 14, 38
Scheduler 101
SD Card 105, 106
Sector Scan 69
Secure Digital (SD) card 106
SIGMET 49, 57
SiriusXM Lightning 148, 154
SiriusXM Weather 45
SMS 84
STAB 70
Standby 66
Standby Navigation Database 157, 158
Store Flight Plan 33
Stormscope lightning data 43, 44
Stormscope Lightning Data 148
Strike 43
Strike mode 44
SVT 79
Synchronization 155
Synthetic Vision Technology 79
System ID 48
T
TAS 71, 126
Telephone 84, 85, 87, 88, 90, 92
Terminal Aerodrome Forecast (TAF) 45,
49, 57
Terrain 75, 76, 130, 148, 153
Garmin G1000 Cockpit Reference Guide for the Diamond DA42NG
190-00963-04 Rev. A
Index
Flight
Instruments
Terrain-SVS 76, 77
Text Message 88, 89, 91, 92
Tilt line 67
Topographical Data 148, 153
Traffic 43, 71, 153
Traffic advisory 71
Traffic map page 71, 72, 76
Transponder 9, 10, 151, 152
EIS
Nav/Com/
XPDR/Audio
U
AFCS
Universal Access Transceiver (UAT) 72
USP 16, 114
GPS Nav
V
Flight
Planning
Vertical speed guidance 20
Video 100
VNV 17, 110
Vspeed 2
Procedures
W
Hazard
Avoidance
WAAS 136
WATCH® 70
Waypoint Selection Submenu 27, 28
Weather Attenuated Color Highlight 70
Weather data link page 45
Weather Radar 66
Wi-Fi 96, 98
Wind data 150
Winds Aloft 49, 58
WIND Softkey 58, 64
Worldwide Weather 47, 48, 52, 55, 148, 154
Additional
Features
Abnormal
Operation
Annun/
Alerts
Appendix
Index
190-00963-04 Rev. A
Garmin G1000 Cockpit Reference Guide for the Diamond DA42NG
Index-3
Index
Appendix
Annun/
Alerts
Abnormal
Operation
Additional
Features
Hazard
Avoidance
Procedures
Flight
Planning
GPS Nav
AFCS
Nav/Com/
XPDR/Audio
EIS
Flight
Instruments
Index
Blank Page
Index-4
Garmin G1000 Cockpit Reference Guide for the Diamond DA42NG
190-00963-04 Rev. A
Garmin International, Inc.
1200 East 151st Street
Olathe, Kansas 66062, U.S.A.
Tel: 913.397.8200
Fax: 913.397.8282
Aircraft On Ground (AOG) Hotline: 913.397.0836
Aviation Dealer Technical Support: 888.606.5482
Garmin AT, Inc.
2345 Turner Road SE
Salem, OR 97302, U.S.A.
Tel: 503.581.8101
Fax 503.364.2138
Garmin (Europe) Ltd.
Liberty House, Hounsdown Business Park
Southampton, Hampshire SO40 9LR U.K.
Tel: +44 (0) 238 052 4000
Fax: +44 (0) 238 052 4004
Aviation Support: +44 (0) 370 850 1243
Garmin Corporation
No. 68, Zhangshu 2nd Road
Xizhi District, New Taipei City, Taiwan
Tel: 34-93-357-2608
Fax: 34-93-429-4484
www.garmin.com
© 2009, 2011-2012, 2014, 2016 Garmin Ltd. or its subsidiaries
190-00963-04 Rev. A
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising