Garmin | G1000: Mooney M20M | Garmin G1000: Mooney M20M G1000/GFC 700 Instructions for Continued Airworthiness

Garmin G1000: Mooney M20M G1000/GFC 700 Instructions for Continued Airworthiness
G1000 / GFC 700
Instructions for Continued
Airworthiness
Mooney M20M/M20R
190-00638-02
May 2006
Revision A
© Copyright 2006
Garmin Ltd. or its subsidiaries
All Rights Reserved
Except as expressly provided herein, no part of this manual may be reproduced, copied, transmitted,
disseminated, downloaded or stored in any storage medium, for any purpose without the express prior
written consent of Garmin. Garmin hereby grants permission to download a single copy of this manual
and of any revision to this manual onto a hard drive or other electronic storage medium to be viewed and
to print one copy of this manual or of any revision hereto, provided that such electronic or printed copy of
this manual or revision must contain the complete text of this copyright notice and provided further that
any unauthorized commercial distribution of this manual or any revision hereto is strictly prohibited.
Garmin International, Inc.
1200 E. 151st Street
Olathe, KS 66062 USA
Telephone: 913-397-8200
www.garmin.com
Garmin (Europe) Ltd.
Unit 5, The Quadrangle
Abbey Park Industrial Estate
Romsey, SO51 9DL U.K.
Telephone: 44/1794.519944
RECORD OF REVISIONS
Revision Revision Date
Description
A
05/04/2006
Initial release for M20/GFC700 STC
ECO #
------
DOCUMENT PAGINATION
Section
Table of Contents
Section 1
Section 2
Page A
Revision A
Pagination
i – vi
1-1 – 1-2
2-1 – 2-4
G1000/GFC 700 ICA – Mooney M20
190-00638-02
INFORMATION SUBJECT TO EXPORT CONTROL LAWS
This document may contain information which is subject to the Export Administration Regulations
("EAR") issued by the United States Department of Commerce (15 CFR, Chapter VII, Subchapter C) and
which may not be exported, released, or disclosed to foreign nationals inside or outside of the United
States without first obtaining an export license. A violation of the EAR may be subject to a penalty of up
to 10 years imprisonment and a fine of up to $1,000,000 under Section 2410 of the Export Administration
Act of 1979. Include this notice with any reproduced portion of this document.
IMPORTANT
All references to Mooney M20M aircraft made in this document equally apply to Mooney M20R aircraft,
unless otherwise noted.
G1000/GFC 700 ICA – Mooney M20
190-00638-02
Page i
Revision A
TABLE OF CONTENTS
PARAGRAPH
PAGE
1
INTRODUCTION
1-1
1.1
CONTENT, SCOPE, PURPOSE ..........................................................................................................1-1
1.2
AIRWORTHINESS LIMITATIONS .....................................................................................................1-1
1.3
ORGANIZATION .............................................................................................................................1-2
1.4
REVISION & DISTRIBUTION...........................................................................................................1-2
2
SERVICING INFORMATION 2-1
2.1
ON CONDITION SERVICING ...........................................................................................................2-1
2.2
RECOMMENDED TOOLS.................................................................................................................2-1
2.3
MAINTENANCE INTERVALS ...........................................................................................................2-2
Page ii
Revision A
G1000/GFC 700 ICA – Mooney M20
190-00638-02
1.3
Organization
The Instructions for Continued Airworthiness for this STC is composed of multiple documents.
Table 1-1 defines the documents which compose a complete set of ICA for this STC.
Table 1-1. ICA Structure
Document
Part Number
This Document
G1000/GFC 700 Instructions for Continued Airworthiness
(Principal Manual)
ICA Content
- Airworthiness Limitations
- Maintenance Intervals
- Inspection Requirements
- System Description
- Control & Operation
- Special Maintenance
Considerations
G1000/GFC 700 System Maintenance Manual – M20
190-00638-01
- Servicing Information
- Troubleshooting Information
- Removal & Replacement
- Software/Configuration
Loading
- Return To Service
G1000/GFC 700 General Arrangement Drawing – M20M/R
005-00343-03
G1000/GFC 700 Pitch Servo Installation Drawing – M20M/R
005-00343-05
G1000/GFC 700 Pitch Trim Servo Installation Drawing – M20M/R
005-00343-07
G1000/GFC 700 Roll Servo Installation Drawing – M20M/R
005-00343-06
G1000/GFC 700 Wiring Routing – M20M/R
005-00343-10
G1000/GFC 700 Wiring Diagram – M20M/R
005-00343-04
G1000/GFC 700 Electrical Removal – M20M/R
005-00343-30
G1000/GFC 700 Structural Removal – M20M/R
005-00343-41
G1000/GFC 700 Flap Logic Relay Track – M20M/R
005-00343-40
G1000/GFC 700 Control Wheel Mod – M20M/R
005-00343-12
G1000/GFC 700 Instrument Panel Mod – M20M/R
005-00343-11
Mooney M20M Airplane Maintenance Manual
Mooney P/N 151
Mooney M20R Airplane Maintenance Manual
Mooney P/N 160
1.4
- Supporting Installation
Diagrams
- Supporting Maintenance Data
Revision & Distribution
This document is required for maintaining the continued airworthiness of the aircraft. Revisions to this
document will be made by Garmin and will be distributed by Garmin per standard documentation revision
procedures.
For the latest revision to this document, check Garmin’s web site at: www.garmin.com/ and click on
‘Dealers Only’.
NOTE
Only Garmin-authorized dealers and service centers are given access to the Dealer
portion of the Web Site. If you do not have a Dealer Password, contact Garmin directly
for the latest revision of this document.
Page 1-2
Revision A
G1000/GFC 700 ICA – Mooney M20
190-00638-02
2
Servicing Information
2.1
On Condition Servicing
G1000 LRU maintenance is ‘on condition’ only. No component-level overhaul is required for this type
design change.
‘On Condition’ replacement and/or servicing should occur when an item exhibits conditions, symptoms,
and/or abnormalities defined by the troubleshooting section in the G1000/GFC 700 System Maintenance
Manual. Replacement and/or servicing should be made only after the technician troubleshoots the system
to the extent determined necessary by using the guidance in this manual along with common avionics
maintenance practices.
2.2
Recommended Tools
The following tools are needed to perform maintenance tasks on G1000/GFC 700 equipment:
x
Mili-ohm Meter, OR
9 Agilent 34410A Ammeter or equivalent
9 Fluke 187 Voltmeter or equivalent
9 Power Supply capable of providing 1 amp current
#2 Phillips Screwdriver
x
3/32” Hex Tool
x
Digital Level (Required for AHRS ‘Procedure A’ Calibration)
x
A VHF NAV/COM/ILS ramp tester or equivalent
x
A transponder ramp tester or equivalent
x
A pitot/static ramp tester
x
Outdoor line-of-site to GPS satellite signals or GPS indoor repeater
x
Headset/Microphone
x
Ground Power Unit (Capable of supplying 28 Vdc)
x
Servo Mount Slip Clutch Adjustment Tool – P/N 011-01085-00 or -01 (-01 is required for pitch
and roll clutch adjustments)
x
Calibrated Torque Wrench capable of measuring 0 – 70 in/lbs
x
Flight Control Cable Tension Meter
x
Standard Sockets & Wrenches (3/8”, 9/16”, and 13/16”)
x
G1000/GFC 700 ICA – Mooney M20
190-00638-02
Page 2-1
Revision A
2.3
Maintenance Intervals
The following table shows systems and items that must undergo tests or checks at specific intervals, either
in flight hours or calendar months. If the interval is shown to be in flight time as well as calendar months,
the first interval reached should be used as the limit.
Table 2-1. Maintenance Intervals
Item
Description/Procedure
System Maint.
Manual
Section No.
Interval
4.2
Aircraft Annual
G1000 Equipment
G1000 System
Complete Visual Inspection
GDU 1040 PFD
6.1
GDU 1042 MFD
GMA 1347
Removal & Replacement.
6.2
GIA 63 IAU (Qty. 2)
6.3
GEA 71 EAU
6.4
GTX 33 Mode S
Transponder
Removal & Replacement.
Test according to Title 14 CFR §§ 91.411
and 91.413 as well as Part 43 Appendix F.
Removal & Replacement.
6.5
7.5.3
24 Months
6.6
On Condition
Altimeter (system) test according to Title 14
CFR § 91.411 and Part 43 Appendix E.
24 Months
GDC 74A
Airspeed Function Test.
7.6.3
2000 Hours or 48
Months
2000 Hours or 48
Months
Vertical Speed Function Test.
GRS 77 AHRS
On Condition
Magnetic variation database update.
6.8
Removal & Replacement.
4.5
GMU 44
Magnetometer
Removal & Replacement (with a new serial
number unit).
7.7.6
GDL 69/69A
(Optional)
Removal & Replacement.
7.9.3
On Condition
G1000 Accessories
Configuration Module
Replacement (Qty 4)
Removal & Replacement.
6.13
GEA 71 Backshell
Thermocouple
Removal & Replacement.
6.14
OAT Probe
Removal & Replacement.
6.7
Mid-Continent
Standby Attitude Ind.
Removal & Replacement: Refer to
appropriate Mooney M20 Maintenance
Manual.
PFD, MFD, & GIA
Cooling Fans (Qty 3)
Page 2-2
Revision A
Removal & Replacement: Refer to Mooney
G1000 System Installation Drawing, 950300.
On Condition
N/A
N/A
G1000/GFC 700 ICA – Mooney M20
190-00638-02
Item
Description/Procedure
System Maint.
Manual
Section No.
Interval
GFC 700 AFCS
GFC 700 AFCS
System
Complete Visual Inspection
4.2
Aircraft Annual
Flap Discrete
Function Check*
Test the flap-in-motion discrete inputs to
the G1000 to verify proper operation.
4.8
100 Hours or
Annual
Removal & Replacement.
6.11
On Condition
Clean and Apply Grease to Output Gears.
4.6
1000 Hours or 36
Months
Removal & Replacement.
Refer to Pitch
Servo Installation
Drawing 00500343-03.
On Condition
Removal & Replacement.
Refer to Pitch
Trim Servo
Installation
Drawing
005-00343-07.
On Condition
Removal & Replacement.
6.12
On Condition
Check Slip Clutch Torque (adjust if
necessary)
4.7
500 Hours or 12
Months
GSA 81 Servos (all)
Pitch Bridle Cable
Pitch Trim Chain
GSM 85 Servo
Mounts (all)
*Denotes Airworthiness Limitation Maintenance Requirement (See Section 1.2)
G1000/GFC 700 ICA – Mooney M20
190-00638-02
Page 2-3
Revision A
Item
Description/Procedure
System Maint.
Manual
Section No.
Interval
Engine/Airframe Sensors
MAP Sensor
Oil Pressure Sensor
Oil Temperature
Sensor
Tach Sensor
Fuel Flow Sensor
Removal & Replacement:
CHT Probes (Qty 6)
Refer to appropriate Mooney M20
Maintenance Manual.
N/A
EGT Probes
(Qty 6 M20M)
(Qty 7 M20R)
On Condition
TIT Probe (M20R)
Battery Current
Sensor
Fuel Tank Quantity
Sending Units –
G1000 Fuel Tank
Recalibration
Removal & Replacement:
Refer to appropriate Mooney M20
Maintenance Manual. New replacement
fuel quantity probe(s) must be recalibrated .
4.4
G1000 Lightning Protection
Replace the voltage suppressor unit. Refer
to G1000/GFC 700 Wiring Diagram –
M20M/R.
The Standby Attitude Indicator Voltage
Suppressor is located behind instrument
panel near the Standby Attitude Indicator
harness connector.
N/A
Replace After
Suspected / Actual
Lighting Event
Visual Inspection
Complete Visual Inspection
4.2
Aircraft Annual
Electrical Bonding
Test
Perform an electrical bonding resistance
check of all G1000 equipment.
TVS Unit
Replacement
4.3.2
1000 Hours and
After
Suspected / Actual
Lighting Event
----- END ----
Page 2-4
Revision A
G1000/GFC 700 ICA – Mooney M20
190-00638-02
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising