Garmin | G1000: Piper PA-44-180 Seminole | Garmin G1000: Piper PA-44-180 Seminole Piper PA-44-180 Seminole G1000 Cockpit Reference Guide

Garmin G1000: Piper PA-44-180 Seminole Piper PA-44-180 Seminole G1000 Cockpit Reference Guide
G1000
®
Integrated Flight Deck
Cockpit Reference Guide for the Piper PA-44-180 Seminole
FLIGHT INSTRUMENTS
ENGINE INDICATION SYSTEM
NAV/COM/TRANSPONDER/AUDIO PANEL
GPS NAVIGATION
FLIGHT PLANNING
PROCEDURES
HAZARD AVOIDANCE
ADDITIONAL FEATURES
ABNORMAL OPERATION
ANNUNCIATIONS & ALERTS
APPENDIX
INDEX
Copyright © 2013 Garmin Ltd. or its subsidiaries. All rights reserved.
This manual reflects the operation of System Software version 1648.01 or later for the Piper
PA-44-180 Seminole. Some differences in operation may be observed when comparing the
information in this manual to earlier or later software versions.
Garmin International, Inc., 1200 East 151st Street, Olathe, Kansas 66062, U.S.A.
Tel: 913/397.8200Fax: 913/397.8282
Garmin AT, Inc., 2345 Turner Road SE, Salem, OR 97302, U.S.A.
Tel: 503/391.3411Fax 503/364.2138
Garmin (Europe) Ltd, Liberty House, Bulls Copse Road, Hounsdown Business Park,
Southampton, SO40 9RB, U.K.
Tel: 44/0870.8501241
Fax: 44/0870.8501251
Garmin Corporation, No. 68, Jangshu 2nd Road, Shijr, Taipei County, Taiwan
Tel: 886/02.2642.9199
Fax: 886/02.2642.9099
For after-hours emergency, aircraft on ground (AOG) technical support for Garmin panel mount
and integrated avionics systems, please contact Garmin’s AOG Hotline at 913.397.0836.
Web Site Address: www.garmin.com
Except as expressly provided herein, no part of this manual may be reproduced, copied,
transmitted, disseminated, downloaded or stored in any storage medium, for any purpose
without the express written permission of Garmin. Garmin hereby grants permission to
download a single copy of this manual and of any revision to this manual onto a hard drive or
other electronic storage medium to be viewed for personal use, provided that such electronic
or printed copy of this manual or revision must contain the complete text of this copyright
notice and provided further that any unauthorized commercial distribution of this manual or any
revision hereto is strictly prohibited.
Garmin® and G1000® are registered trademarks of Garmin Ltd. or its subsidiaries. FliteCharts®,
and SafeTaxi® are trademarks of Garmin Ltd. or its subsidiaries. These trademarks may not be
used without the express permission of Garmin.
NavData® is a registered trademark of Jeppesen, Inc.; Stormscope® is a registered trademark
of L-3 Communications; Honeywell® and Bendix/King® are registered trademarks of
Honeywell International, Inc.
SiriusXM Weather and SiriusXM Satellite Radio are provided by SiriusXM Satellite Radio, Inc.
AOPA Membership Publications, Inc. and its related organizations (hereinafter collectively
“AOPA”) expressly disclaim all warranties, with respect to the AOPA information included in this
data, express or implied, including, but not limited to, the implied warranties of merchantability
and fitness for a particular purpose. The information is provided “as is” and AOPA does not
warrant or make any representations regarding its accuracy, reliability, or otherwise. Under
no circumstances including negligence, shall AOPA be liable for any incidental, special or
consequential damages that result from the use or inability to use the software or related
documentation, even if AOPA or an AOPA authorized representative has been advised of the
possibility of such damages. User agrees not to sue AOPA and, to the maximum extent allowed
by law, to release and hold harmless AOPA from any causes of action, claims or losses related
to any actual or alleged inaccuracies in the information. Some jurisdictions do not allow the
limitation or exclusion of implied warranties or liability for incidental or consequential damages
so the above limitations or exclusions may not apply to you.
AC-U-KWIK and its related organizations (hereafter collectively “AC-U-KWIK Organizations”)
expressly disclaim all warranties with respect to the AC-U-KWIK information included
in this data, express or implied, including, but not limited to, the implied warranties of
merchantability and fitness for a particular purpose. The information is provided “as is” and
AC-U-KWIK Organizations do not warrant or make any representations regarding its accuracy,
reliability, or otherwise. Licensee agrees not to sue AC-U-KWIK Organizations and, to the
maximum extent allowed by law, to release and hold harmless AC-U-KWIK Organizations
from any cause of action, claims or losses related to any actual or alleged inaccuracies in the
information arising out of Garmin’s use of the information in the datasets. Some jurisdictions
do not allow the limitation or exclusion of implied warranties or liability for incidental or
consequential damages so the above limitations or exclusions may not apply to licensee.
June, 2013
190-01462-00 Rev. A
Printed in the U.S.A.
Warnings, Cautions & Notes
WARNING: Do not use the terrain avoidance feature as the sole means of
navigation and terrain separation. The terrain avoidance feature is only to
be used as and aid to terrain avoidance. Garmin obtains terrain database
content from third party sources and is not able to independently verify the
accuracy of the terrain data.
WARNING: Do not rely on the displayed minimum safe altitude (MSAs) as
the sole source of obstacle and terrain avoidance information. The displayed
minimum safe altitudes (MSAs) are only advisory in nature. Always refer to
current aeronautical charts for appropriate minimum clearance altitudes.
WARNING: Do not use GPS-derived geometric altitude for compliance with air
traffic control altitude requirements in the National Airspace System (NAS) or
internationally. The primary barometric altimeter must be used for compliance
with all air traffic control altitude regulations, requirements, instructions, and
clearance.
WARNING: Do not use outdated database information. Databases used in
the system must be updated regularly in order to ensure that the information
remains current.
WARNING: Do not use basemap (land and water data) information for
primary navigation. Basemap data is intended only to supplement other
approved navigation data sources and should be considered only an aid to
enhance situational awareness.
WARNING: Do not rely solely upon the display of traffic information for
collision avoidance maneuvering. The traffic display does not provide collision
avoidance resolution advisories and does not under any circumstances or
conditions relieve the pilot’s responsibility to see and avoid other aircraft.
WARNING: Do not rely solely upon the display of traffic information to
accurately depict all of the traffic within range of the aircraft. Due to lack
of equipment, poor signal reception, and/or inaccurate information from
aircraft or ground stations, traffic may be present that is not represented on
the display.
190-01462-00 Rev. A
Garmin G1000 Cockpit Reference Guide for the Piper PA-44-180 Seminole
Warnings, Cautions & Notes
WARNING: Do not use data link weather information for maneuvering in,
near or around areas of hazardous weather. Information contained within data
link weather products may not accurately depict current weather conditions.
WARNING: Do not use the indicated data link weather product age to
determine the age of the weather information shown by the data link weather
product. Due to time delays inherent in gathering and processing weather
data for data link transmission, the weather information shown by the data
link weather product may be significantly older than the indicated weather
product age.
WARNING: Do not rely on information from the lightning detection system
display as the sole basis for hazard weather avoidance. Range limitations
and interference may cause the system to display inaccurate or incomplete
information. Refer to the documentation from the lightning detection system
manufacturer for detailed information about the system.
WARNING: The Garmin system, as installed in this aircraft, has a very
high degree of functional integrity. However, the pilot must recognize that
providing monitoring and/or self-test capability for all conceivable system
failures is not practical.
WARNING: Do not use the system until carefully reviewing, and gaining
a thorough understanding of all aspects of the system’s Pilot’s Guide
documentation and the Airplane Flight Manual. Do not attempt to learn
system operational procedures while the aircraft is in the air. For safety
reasons, system operational procedures must be learned on the ground.
WARNING: The United States government operates the Global Positioning
System and is solely responsible for its accuracy and maintenance. The
GPS system is subject to changes which could affect the accuracy and
performance of all GPS equipment. Portions of the system utilize GPS as a
precision electronic NAVigation AID (NAVAID). Therefore, as with all NAVAIDs,
information presented by the system can be misused or misinterpreted and,
therefore, become unsafe.
Garmin G1000 Cockpit Reference Guide for the Piper PA-44-180 Seminole
190-01462-00 Rev. A
Warnings, Cautions & Notes
WARNING: To reduce the risk of unsafe operation, carefully review and
understand all aspects of the Pilot’s Guide documentation and the Airplane
Flight Manual. Thoroughly practice basic operation prior to actual use. During
flight operations, carefully compare indications from the system to all available
navigation sources, including the information from other NAVAIDs, visual
sightings, charts, etc. For safety purposes, always resolve any discrepancies
before continuing navigation.
WARNING: Do not use the system to attempt to penetrate a thunderstorm.
The illustrations in this guide are only examples. Both the FAA Advisory
Circular, Subject: Thunderstorms, and the Aeronautical Information Manual
(AIM) recommend avoiding any thunderstorm identified as severe of giving
intense radar echo by at least 20 miles.
WARNING: Lamp(s) inside this product contain mercury (HG) and must
be recycled or disposed of according to local, state, or federal laws. For
more information, refer to our website at www.garmin.com/aboutGarmin/
environment/disposal.jsp.
WARNING: Because of variation in the earth’s magnetic field, operating the
system within the following areas could result in loss of reliable attitude and
heading indications. North of 72° North latitude at all longitudes. South of
70° South latitude at all longitudes. North of 65° North latitude between
longitude 75° W and 120° W. (Northern Canada). North of 70° North latitude
between longitude 70° W and 128° W. (Northern Canada). North of 70° North
latitude between longitude 85° E and 114° E. (Northern Russia). South of
55° South latitude between longitude 120° E and 165° E. (Region south of
Australia and New Zealand).
WARNING: Do not use GPS to navigate to any active waypoint identified as
a ‘NON WGS84 WPT’ by a system message. ‘NON WGS84 WPT’ waypoints are
derived from an unknown map reference datum that may be incompatible
with the map reference datum used by GPS (known as WGS84) and may be
positioned in error as displayed.
190-01462-00 Rev. A
Garmin G1000 Cockpit Reference Guide for the Piper PA-44-180 Seminole
Warnings, Cautions & Notes
CAUTION: The PFD and MFD displays use a lens coated with a special
anti-reflective coating that is very sensitive to skin oils, waxes, and abrasive
cleaners. CLEANERS CONTAINING AMMONIA WILL HARM THE ANTIREFLECTIVE COATING. It is very important to clean the lens using a clean,
lint-free cloth and an eyeglass lens cleaner that is specified as safe for antireflective coatings.
CAUTION: The system does not contain any user-serviceable parts. Repairs
should only be made by an authorized Garmin service center. Unauthorized
repairs or modifications could void both the warranty and the pilot’s authority
to operate this device under FAA/FCC regulations.
NOTE: When using Stormscope, there are several atmospheric phenomena
in addition to nearby thunderstorm that can cause isolated discharge points
in the strike display mode. However, clusters of two or more discharge points
in the strike display mode do indicate thunderstorm activity if these points
reappear after the screen has been cleaned.
NOTE: Do not rely upon data link services to provide Temporary Flight
Restriction (TFR) information. Always confirm TFR information through official
sources such as Flight Service Stations or Air Traffic Control.
NOTE: All visual depictions contained within this document, including screen
images of the panel and displays, are subject to change and may not reflect
the most current system and databases. Depictions of equipment may differ
slightly from the actual equipment.
NOTE: This device complies with part 15 of the FCC Rules. Operation is
subject to the following two conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
Garmin G1000 Cockpit Reference Guide for the Piper PA-44-180 Seminole
190-01462-00 Rev. A
Warnings, Cautions & Notes
NOTE: This product, its packaging, and its components contain chemicals
known to the State of California to cause cancer, birth defects, or reproductive
harm. This notice is being provided in accordance with California’s Proposition
65. If you have any questions or would like additional information, please
refer to our web site at www.garmin.com/prop65.
NOTE: Interference from GPS repeaters operating inside nearby hangars can
cause an intermittent loss of attitude and heading displays while the aircraft
is on the ground. Moving the aircraft more than 100 yards away from the
source of the interference should alleviate the condition.
NOTE: Use of polarized eyewear may cause the flight displays to appear dim
or blank.
NOTE: Garmin requests the flight crew report any observed discrepancies
related to database information. These discrepancies could come in the form
of an incorrect procedure; incorrectly identified terrain, obstacles and fixes; or
any other displayed item used for navigation or communication if the air or
on the ground. Go to FlyGarmin.com and select Aviation Data Error Report.
NOTE: The purpose of this Cockpit Reference Guide is to provide the pilot
a resource with which to find operating instructions on the major features
of the G1000 system more easily. It is not intended to be a comprehensive
operating guide. Complete operating procedures for the system are found
in the G1000 Pilot’s Guide for this aircraft.
190-01462-00 Rev. A
Garmin G1000 Cockpit Reference Guide for the Piper PA-44-180 Seminole
Warnings, Cautions & Notes
Blank Page
Garmin G1000 Cockpit Reference Guide for the Piper PA-44-180 Seminole
190-01462-00 Rev. A
Record of Revisions
Part Number
190-01462-00
Change Summary
Initial release
Revision Date of Revision Affected Pages
A
June, 2013
All
190-01462-00 Rev. A
Description
Initial release
Garmin G1000 Cockpit Reference Guide for the Piper PA-44-180 Seminole
RR-1
Record of Revisions
Blank Page
RR-2
Garmin G1000 Cockpit Reference Guide for the Piper PA-44-180 Seminole
190-01462-00 Rev. A
Table of Contents
FLIGHT INSTRUMENTS................................................................................................................. 1
Selecting the Altimeter Barometric Pressure Setting....................................................... 1
Selecting Standard Barometric Pressure (29.92 in Hg)..................................................... 1
Change Altimeter Barometric Pressure Setting Units....................................................... 1
Change Navigation Sources.................................................................................................... 1
Enable/Disable OBS Mode While Navigating with GPS..................................................... 2
Generic Timer.............................................................................................................................. 2
Turn ALL Vspeed Bugs On or Off............................................................................................. 2
Set Barometric Minimum Descent Altitude......................................................................... 2
Displaying Wind Data............................................................................................................... 3
ENGINE INDICATION..................................................................................................................... 5
Engine Display............................................................................................................................ 5
Engine Page................................................................................................................................ 7
Landing Gear Indications....................................................................................................... 10
NAV/COM/TRANSPONDER/AUDIO PANEL........................................................................ 11
Enter a Transponder Code..................................................................................................... 11
DME Tuning............................................................................................................................... 11
Selecting a COM Radio........................................................................................................... 11
Selecting a NAV Radio............................................................................................................ 11
NAV/COM Tuning...................................................................................................................... 12
Digital Clearance Recorder and Player............................................................................... 12
Intercom System (ICS) Isolation........................................................................................... 13
GPS NAVIGATION......................................................................................................................... 15
Direct-to Navigation............................................................................................................... 15
Activate a Stored Flight Plan................................................................................................ 16
Activate a Flight Plan Leg...................................................................................................... 16
Stop Navigating a Flight Plan............................................................................................... 17
Vertical Navigation (VNAV)................................................................................................... 17
FLIGHT PLANNING....................................................................................................................... 21
Weight Planning....................................................................................................................... 21
Trip Planning............................................................................................................................. 21
Create a User Waypoint Defined by Latitude & Longitude............................................ 23
Create a User Waypoint Defined by Radials from Other Waypoints............................ 24
Create a User Waypoint Defined by a Radial & Distance from Another Waypoint... 25
Create a User Waypoint using the Map Pointer............................................................... 27
Delete a User Waypoint.......................................................................................................... 28
Create a Flight Plan................................................................................................................. 28
Import a Flight Plan from an SD Card................................................................................. 29
Insert a Waypoint in the Active Flight Plan....................................................................... 30
190-01462-00 Rev. A
Garmin G1000 Cockpit Reference Guide for the Piper PA-44-180 Seminole
i
Table of Contents
Enter an Airway in a Flight Plan........................................................................................... 31
User-Defined Holding Patterns............................................................................................. 31
Invert An Active Flight Plan................................................................................................... 34
Remove a Departure, Arrival, Approach, or Airway from a Flight Plan...................... 34
Store a Flight Plan................................................................................................................... 34
Edit a Stored Flight Plan........................................................................................................ 35
Delete a Waypoint from the Flight Plan............................................................................. 35
Invert and Activate a Stored Flight Plan............................................................................ 36
Copy a Flight Plan.................................................................................................................... 36
Delete a Flight Plan................................................................................................................. 36
Graphical Flight Plan Creation.............................................................................................. 37
Export a Flight Plan to an SD Card...................................................................................... 37
PROCEDURES.................................................................................................................................. 39
Load and Activate a Departure Procedure........................................................................ 39
Activate A Departure Leg...................................................................................................... 39
Load An Arrival Procedure..................................................................................................... 39
Activate An Arrival Leg.......................................................................................................... 40
Load and/or Activate an Approach Procedure.................................................................. 40
Activate An Approach in the Active Flight Plan................................................................ 42
Activate a Vector to Final Approach Fix............................................................................. 42
Activate A Missed Approach in the Active Flight Plan.................................................... 42
Temperature Compensated Altitude.................................................................................. 42
HAZARD AVOIDANCE................................................................................................................. 45
Customizing the Hazard Displays on the Navigation Map............................................. 45
SiriusXM Weather (Optional)................................................................................................ 45
Traffic Systems......................................................................................................................... 48
Terrain And Obstacle Proximity............................................................................................ 52
Terrain-SVS................................................................................................................................ 53
Terrain Awareness & Warning System (TAWS-B) Display (Optional)............................ 55
ADDITIONAL FEATURES............................................................................................................ 57
Synthetic Vision (Optional).................................................................................................... 57
Terminal Procedure Charts.................................................................................................... 58
Airport Directory..................................................................................................................... 60
SiriusXM Radio Entertainment............................................................................................. 61
Pilot Profiles............................................................................................................................. 64
ii
Garmin G1000 Cockpit Reference Guide for the Piper PA-44-180 Seminole
190-01462-00 Rev. A
Table of Contents
ABNORMAL OPERATION.......................................................................................................... 69
Reversionary Mode................................................................................................................. 69
Abnormal COM Operation..................................................................................................... 69
Hazard Displays with Loss of GPS Position........................................................................ 69
Unusual Attitudes.................................................................................................................... 70
Dead Reckoning....................................................................................................................... 70
ANNUNCIATIONS & ALERTS.................................................................................................... 73
G1000 System Annunciations................................................................................................ 73
CAS Annunciations................................................................................................................... 75
System Messages..................................................................................................................... 76
Voice Alerts............................................................................................................................... 77
Terrain-SVT Alerts.................................................................................................................... 77
Terrain-SVT System Status Annunciations......................................................................... 78
TAWS-B Alerts........................................................................................................................... 79
TAWS-B System Status Annunciations................................................................................ 80
GDL 69/69A Data Link Receiver Messages......................................................................... 81
MFD & PFD Message Advisories........................................................................................... 82
Database Message Advisories.............................................................................................. 83
GMA 1347 Message Advisories............................................................................................. 86
GIA 63W Message Advisories................................................................................................ 87
GEA 71 Message Advisories................................................................................................... 90
GTX 33/33 w/ES Message Advisories................................................................................... 90
GRS 77 Message Advisories................................................................................................... 91
GMU 44 Message Advisories................................................................................................. 92
GDL 69A Message Advisories................................................................................................ 92
GTS 800 Message Advisories................................................................................................. 92
GDC 74A Message Advisories................................................................................................ 93
Miscellaneous Message Advisories...................................................................................... 93
Flight Plan Import/Export Messages................................................................................... 97
Pilot Profile Import/Export Messages................................................................................. 99
APPENDIX...................................................................................................................................... 101
PFD Softkey Map................................................................................................................... 101
MFD Softkey Map.................................................................................................................. 106
Loading Updated Databases............................................................................................... 109
INDEX..........................................................................................................................................Index-1
190-01462-00 Rev. A
Garmin G1000 Cockpit Reference Guide for the Piper PA-44-180 Seminole
iii
Table of Contents
Blank Page
iv
Garmin G1000 Cockpit Reference Guide for the Piper PA-44-180 Seminole
190-01462-00 Rev. A
Flight Instruments
Flight
Instruments
FLIGHT INSTRUMENTS
SELECTING THE ALTIMETER BAROMETRIC PRESSURE SETTING
EIS
Turn the BARO Knob to select the desired setting.
1)
Press the PFD Softkey.
2)
Press the STD BARO Softkey to set standard barometric pressure.
Nav/Com/
XPDR/Audio
SELECTING STANDARD BAROMETRIC PRESSURE (29.92 IN HG)
GPS Nav
CHANGE ALTIMETER BAROMETRIC PRESSURE SETTING UNITS
2)
Press the ALT UNIT Softkey.
3)
Press the IN Softkey to display the barometric pressure setting in inches of
mercury (in Hg).
Procedures
Press the PFD Softkey to display the second-level softkeys.
Flight
Planning
1)
Or:
4)
Hazard
Avoidance
Press the HPA Softkey to display the barometric pressure setting in
hectopascals.
Press the BACK Softkey to return to the top-level softkeys.
2)
Press the CDI Softkey again to change from VOR1 or LOC1 to VOR2
or LOC2. This places the light blue tuning box over the NAV2 standby
frequency.
3)
Press the CDI Softkey a third time to return to GPS.
Annun/Alerts
Press the CDI Softkey to change from GPS to VOR1 or LOC1. This places
the light blue tuning box over the NAV1 standby frequency in the upper left
corner of the PFD.
Abnormal
Operation
1)
Additional
Features
CHANGE NAVIGATION SOURCES
Appendix
Index
190-01462-00 Rev. A
Garmin G1000 Cockpit Reference Guide for the Piper PA-44-180 Seminole
1
ENABLE/DISABLE OBS MODE WHILE NAVIGATING WITH GPS
1)
Press the OBS Softkey to select OBS Mode.
2)
Turn a CRS Knob to select the desired course to/from the waypoint. Press
the CRS Knob to synchronize the Selected Course with the bearing to the
next waypoint.
3)
Press the OBS Softkey again to disable OBS Mode.
GENERIC TIMER
Press the TMR/REF Softkey, then turn the large FMS Knob to select the
time field (hh/mm/ss). Turn the FMS Knobs to set the desired time, then
press the ENT Key. The UP/DOWN field is now highlighted.
2)
Turn the small FMS Knob to display the UP/DOWN window. Turn the FMS
Knob to select ‘UP’ or ‘DOWN’, then press the ENT Key. ‘START?’ is now
highlighted.
3)
Press the ENT Key to START, STOP, or RESET the timer (if the timer is
counting DOWN, it will start counting UP after reaching zero). Press the
CLR Key or the TMR/REF Softkey to remove the window.
1)
Press the TMR/REF Softkey.
2)
Press the MENU Key.
3)
Turn the FMS Knob to highlight the desired option.
4)
Press the ENT Key. Press the TMR/REF Softkey to remove the window.
SET BAROMETRIC MINIMUM DESCENT ALTITUDE
Annun/Alerts
Abnormal
Operation
1)
TURN ALL VSPEED BUGS ON OR OFF
Additional
Features
Hazard
Avoidance
Procedures
Flight
Planning
GPS Nav
Nav/Com/
XPDR/Audio
EIS
Flight
Instruments
Flight Instruments
Index
Appendix
1) Press the TMR/REF Softkey.
2
2)
Turn the large FMS Knob to highlight the Minimums field.
3)
Turn the small FMS Knob to select BARO, or TEMP COMP. OFF is selected
by default. Press the ENT Key or turn the large FMS Knob to highlight the
next field.
4)
Use the small FMS Knob to enter the desired altitude (from zero to 16,000
feet).
Garmin G1000 Cockpit Reference Guide for the Piper PA-44-180 Seminole
190-01462-00 Rev. A
Flight Instruments
6)
To remove the window, press the CLR Key or the TMR/REF Softkey.
EIS
If TEMP COMP was selected, press the ENT Key or turn the large FMS
Knob to highlight the next field and then enter the destination airport
temperature (-59˚C to 59˚C). The temperature compensated altitude
minimum is displayed below the previously enter minimum altitude value.
Flight
Instruments
5)
Press the PFD Softkey.
2)
Press the WIND Softkey to display wind data below the Selected Heading.
3)
Press one of the OPTN softkeys to change how wind data is displayed.
4)
To remove the Wind Data Window, press the OFF Softkey.
GPS Nav
1)
Nav/Com/
XPDR/Audio
DISPLAYING WIND DATA
Flight
Planning
Procedures
Hazard
Avoidance
Additional
Features
Abnormal
Operation
Annun/Alerts
Appendix
Index
190-01462-00 Rev. A
Garmin G1000 Cockpit Reference Guide for the Piper PA-44-180 Seminole
3
Index
Appendix
Annun/Alerts
Abnormal
Operation
Additional
Features
Hazard
Avoidance
Procedures
Flight
Planning
GPS Nav
Nav/Com/
XPDR/Audio
EIS
Flight
Instruments
Flight Instruments
Blank Page
4
Garmin G1000 Cockpit Reference Guide for the Piper PA-44-180 Seminole
190-01462-00 Rev. A
EIS
Flight
Instruments
ENGINE INDICATION
ENGINE DISPLAY
EIS
Nav/Com/
XPDR/Audio
1
GPS Nav
2
3
Flight
Planning
4
5
Procedures
6
Hazard
Avoidance
7
8
Additional
Features
9
10
Abnormal
Operation
11
Annun/Alerts
12
Engine Display when
Engine Page is displayed
Appendix
Engine Display
Index
190-01462-00 Rev. A
Garmin G1000 Cockpit Reference Guide for the Piper PA-44-180 Seminole
5
1
Engine Manifold
Pressure Gauge
(MAN IN HG)
Displays manifold pressure in inches of Mercury (in Hg) to
indicate engine power
2
Tachometer (RPM)
Displays propeller speed in revolutions per minute
(rpm)
3
Propeller Sync
Indicator
Points towards the higher-speed propeller when the
propellers are out of sync.
4
Exhaust Gas
Temperature
(EGT °F)
Displays the temperature for the right and left Exhaust
Gas Temperature for the hottest cylinder (in °F)
5
Fuel Flow Indicator Displays fuel flow in gallons per hour (gph)
(FFLOW GPH)
6
Oil Pressure
Indicator
(OIL PSI)
Displays oil pressure in pounds per square inch (psi)
7
Oil Temperature
Indicator (OIL °F)
Displays oil temperature in degrees Fahrenheit (°F)
8
Alternator
Current(ALTR
AMPS)
Displays each alternator current in amperes
9
Voltage (VOLTS)
Displays the bus voltage.
Appendix
Annun/Alerts
Abnormal
Operation
Additional
Features
Hazard
Avoidance
Procedures
Flight
Planning
GPS Nav
Nav/Com/
XPDR/Audio
EIS
Flight
Instruments
EIS
10 Battery
Displays the battery current in amperes
Current(BATT
AMPS)
11 Fuel Quantity
Indicator (FUEL
QTY GAL)
Displays the amount of fuel in gallons (gal) for each
side of a standard fuel tank.
12 Landing Gear Status Displays landing gear status
Index
(LANDING GEAR)
6
Garmin G1000 Cockpit Reference Guide for the Piper PA-44-180 Seminole
190-01462-00 Rev. A
EIS
Press the ENGINE Softkey or turn the large FMS Knob and select the EIS - Engine
Page.
13
12
EIS
14
Flight
Instruments
ENGINE PAGE
Nav/Com/
XPDR/Audio
1
2
3
GPS Nav
4
5
Flight
Planning
11
6
10
Procedures
7
9
Hazard
Avoidance
8
Engine Page
Displays propeller speed in revolutions per minute
(rpm)
3
Propeller Sync
Indicator
Points towards the higher-speed propeller when the
propellers are out of sync.
4
Exhaust Gas
Temperature
(EGT °F)
Displays the temperature for the right and left Exhaust
Gas Temperature for the hottest cylinder in °F
5
Fuel Flow Indicator Displays fuel flow in gallons per hour (gph)
(FFLOW GPH)
190-01462-00 Rev. A
Garmin G1000 Cockpit Reference Guide for the Piper PA-44-180 Seminole
Index
Tachometer (RPM)
Appendix
2
Annun/Alerts
Displays manifold pressure in inches of Mercury (in Hg) to
indicate engine power
Abnormal
Operation
Engine Manifold
Pressure Gauge
(MAN IN HG)
Additional
Features
1
7
6
Oil Pressure
Indicator
(OIL PSI)
7
Displays oil temperature in degrees Fahrenheit (°F)
Oil Temperature
Indicator (OIL °F)
8
Displays landing gear status
Landing Gear
Status (LANDING
GEAR)
9
Fuel Calculations
Group
(FUEL CALC)
Flight
Planning
GPS Nav
Nav/Com/
XPDR/Audio
EIS
Flight
Instruments
EIS
10 Electrical Group
Procedures
(ELECTRICAL)
11 Engine Hours
Hazard
Avoidance
(TACH TIME)
12 Exhaust Gas
Additional
Features
13 Cylinder Head
Abnormal
Operation
Temperature
(EGT °F)
14 Fuel Quantity
Displays oil pressure in pounds per square inch (psi)
Displays calculated fuel used (GAL USED), endurance
(ENDUR), and range (in nautical miles, RANGE
NM), and fuel efficiency (in nautical miles per gallon,
NMPG) based on the displayed fuel remaining (GAL
REM) and the fuel flow totalizer
Displays alternator (ALTR AMPS) and battery (BATT
AMPS) currents in amperes and bus voltage (VOLTS)
Displays the total time in hours the engine has been
in service
Displays the temperature for the right and left Exhaust
Gas Temperature for the hottest cylinder in °F
Displays head temperatures for all cylinders in °F
Temperature Bar
Graph (CHT °F)
Index
Appendix
Annun/Alerts
Gauges
(L/R FUEL QTY
GAL)
Displays the total amount of fuel and the amount of
fuel in gallons (gal) for each side of a standard fuel
tank
8
Garmin G1000 Cockpit Reference Guide for the Piper PA-44-180 Seminole
190-01462-00 Rev. A
EIS
NOTE: Fuel calculations do not use the aircraft fuel quantity indicators and
are calculated from the last time the fuel was reset.
Flight
Instruments
Fuel Calculations
EIS
Flight
Planning
Procedures
Resetting the fuel totalizer:
On the Engine Page, select the RST FUEL Softkey; this resets displayed fuel
remaining (GAL REM) to the maximum fuel capacity for the aircraft and fuel
used to zero.
GPS Nav
Adjusting the fuel totalizer quantity:
On the Engine Page, use the DEC FUEL and INC FUEL softkeys to obtain the desired
fuel remaining (GAL REM). Each press of the softkey increments or decrements in one
gallon increments.
Nav/Com/
XPDR/Audio
Fuel used (GAL USED), endurance (ENDUR), range (in nautical miles, RANGE
NM), and fuel efficiency (in statute miles per gallon, MPG) are calculated based on the
displayed fuel remaining (GAL REM) and the fuel flow totalizer. The calculated range
also takes into account the aircraft’s heading and the wind direction and speed.
Hazard
Avoidance
Set Fuel Remaining
Calculated Fuel Used
Additional
Features
Calculated Endurance
Calculated Range
Fuel Efficiency
Abnormal
Operation
Fuel Calculations Group
Annun/Alerts
Appendix
Index
190-01462-00 Rev. A
Garmin G1000 Cockpit Reference Guide for the Piper PA-44-180 Seminole
9
Flight
Instruments
EIS
LANDING GEAR INDICATIONS
Landing Gear statuses are shown using the indications in the following table.
EIS
Engine Page
EIS
Position
GPS Nav
Nav/Com/
XPDR/Audio
Up & Locked
Procedures
Flight
Planning
In Transition
Additional
Features
Hazard
Avoidance
Down and
Locked
Abnormal
Operation
Gear Failure
Index
Appendix
Annun/Alerts
Landing Gear Indications
10
Garmin G1000 Cockpit Reference Guide for the Piper PA-44-180 Seminole
190-01462-00 Rev. A
Nav/Com/XPDR/Audio Panel
Flight
Instruments
NAV/COM/TRANSPONDER/AUDIO PANEL
ENTER A TRANSPONDER CODE
Press the CODE Softkey to display the transponder code selection softkeys,
for digit entry.
3)
Press the digit softkeys to enter the code in the code field. When entering
the code, the next key in sequence must be pressed within 10 seconds, or
the entry is cancelled and restored to the previous code. Five seconds after
the fourth digit has been entered, the transponder code becomes active.
Press the DME Softkey.
2)
Turn the large FMS to select the DME source field.
3)
Turn the small FMS Knob to select the desired Nav radio.
4)
Press the ENT Key to complete the selection.
Procedures
1)
Flight
Planning
DME TUNING
Hazard
Avoidance
SELECTING A COM RADIO
Additional
Features
Transmit/Receive
Abnormal
Operation
Press the COM1 MIC, COM2 MIC, or COM3 MIC Key (optional COM, if
installed) on the audio panel.
Receive Only
SELECTING A NAV RADIO
2)
Press the NAV1, NAV2, DME, or ADF Key on the audio panel to select or
deselect the navigation radio audio source. All radio keys can be selected
individually or together.
Garmin G1000 Cockpit Reference Guide for the Piper PA-44-180 Seminole
11
Index
To begin navigating using a navigation radio, press the CDI Softkey on the
PFD to select VOR1/LOC1 (NAV1) or VOR2/LOC2 (NAV2).
Appendix
1)
Annun/Alerts
Press the COM1, COM2, or COM3 Key (optional COM, if installed) on the
audio panel.
190-01462-00 Rev. A
GPS Nav
2)
Nav/Com/
XPDR/Audio
Press the XPDR Softkey to display the transponder mode selection softkeys.
EIS
1)
Press the small tuning knob to select the desired radio for tuning. A light
blue box highlights the radio frequency to be tuned.
2)
Turn the respective tuning knobs to enter the desired frequency into the
standby frequency field. The large knob enters MHz and the small knob
enters kHz.
3)
Press the Frequency Transfer Key to place the frequency into the active
frequency field.
DIGITAL CLEARANCE RECORDER AND PLAYER
NOTE: Only the audio for the selected COM MIC Key is recorded. Audio is
not recorded for COM3 MIC.
Flight
Planning
GPS Nav
1)
EIS
NAV/COM TUNING
Nav/Com/
XPDR/Audio
Flight
Instruments
Nav/Com/XPDR/Audio Panel
Index
Appendix
Annun/Alerts
Abnormal
Operation
Additional
Features
Hazard
Avoidance
Procedures
• Pressing the PLAY Key once plays the latest recorded memory block, then returns
to normal operation.
• Pressing the MKR/MUTE Key while playing a memory block stops play.
• Pressing the PLAY Key during play begins playing the previously recorded
memory block. Each subsequent press of the PLAY Key begins playing the next
previously recorded block.
12
Garmin G1000 Cockpit Reference Guide for the Piper PA-44-180 Seminole
190-01462-00 Rev. A
Nav/Com/XPDR/Audio Panel
Press the PILOT and/or COPLT Key to select those isolated from hearing the Nav/
Com radios.
PILOT KEY
COPLT KEY
ANNUNCIATOR ANNUNCIATOR
Selected
radios; pilot;
copilot;
passengers;
music
Selected
radios; pilot;
copilot;
passengers;
music
Copilot;
passengers;
music
Copilot;
passengers;
music
OFF
PILOT
ON
OFF
Selected
radios; pilot
Copilot
Selected
radios; pilot;
passengers;
music
Selected
radios; pilot;
copilot
Passengers;
music
COPILOT
OFF
ON
Selected
radios; pilot;
passengers;
music
CREW
ON
ON
Selected
radios; pilot;
copilot
Hazard
Avoidance
OFF
Procedures
ALL
Selected
radios; pilot;
copilot;
passengers;
music
Flight
Planning
Passenger
Hears
GPS Nav
Copilot
Hears
Nav/Com/
XPDR/Audio
Pilot Hears
EIS
Mode
Flight
Instruments
INTERCOM SYSTEM (ICS) ISOLATION
Additional
Features
Abnormal
Operation
Annun/Alerts
Appendix
Index
190-01462-00 Rev. A
Garmin G1000 Cockpit Reference Guide for the Piper PA-44-180 Seminole
13
Index
Appendix
Annun/Alerts
Abnormal
Operation
Additional
Features
Hazard
Avoidance
Procedures
Flight
Planning
GPS Nav
Nav/Com/
XPDR/Audio
EIS
Flight
Instruments
Nav/Com/XPDR/Audio Panel
Blank Page
14
Garmin G1000 Cockpit Reference Guide for the Piper PA-44-180 Seminole
190-01462-00 Rev. A
GPS Navigation
Flight
Instruments
GPS NAVIGATION
DIRECT-TO NAVIGATION
2)
3)
6)
7)
11)
12)
Abnormal
Operation
Direct-to Navigation using the PFD
1)
3)
5)
190-01462-00 Rev. A
Garmin G1000 Cockpit Reference Guide for the Piper PA-44-180 Seminole
15
Index
6)
) on the PFD.
Turn the large FMS Knob to place the cursor in the desired selection field.
Turn the small FMS Knob to begin selecting the desired identifier, location,
etc.
Press the ENT Key.
The cursor is now flashing on ‘ACTIVATE?’. If no altitude constraint or
course is desired, press the ENT Key to activate. To enter an altitude
constraint, proceed to step 6.
Turn the large FMS Knob to place the cursor over the ‘ALT’ altitude field.
Appendix
4)
Press the Direct-to Key (
Annun/Alerts
2)
Additional
Features
10)
Hazard
Avoidance
9)
Procedures
8)
Flight
Planning
5)
) Key on the MFD.
Enter the waypoint identifier.
Press the ENT Key to confirm the identifier. The ‘Activate?’ field is
highlighted.
If no altitude constraint or course is desired, press the ENT Key to activate.
To enter an altitude constraint, proceed to step 5.
Turn the large FMS Knob to place the cursor over the ‘VNV’ altitude field.
Enter the desired altitude.
Press the ENT Key. If the waypoint entered is an airport, the option to
select MSL or AGL is now displayed. If the waypoint is not an airport,
proceed to step 9.
Turn the small FMS Knob to select ‘MSL’ or ‘AGL’.
Press the ENT Key. The cursor is now flashing in the VNV offset distance
field.
Enter the desired offset distance before (-) the waypoint.
Press the ENT Key. The ‘Activate?’ field is highlighted.
Press the ENT Key to activate.
GPS Nav
4)
Press the Direct-to (
Nav/Com/
XPDR/Audio
1)
EIS
Direct-to Navigation using the MFD
EIS
Flight
Instruments
GPS Navigation
7)
Turn the small FMS Knob to enter the desired altitude.
8)
Press the ENT Key. If the waypoint entered is an airport, the option to
select MSL or AGL is now displayed. If the waypoint is not an airport,
proceed to step 10.
9)
Turn the small FMS Knob to select ‘MSL’ or ‘AGL’.
Nav/Com/
XPDR/Audio
10) Press the ENT Key. The cursor is placed in the ‘OFFSET’ field.
11) Turn the small FMS Knob to enter the desired target altitude offset from
the selected Direct-to.
GPS Nav
12) Press the ENT Key to highlight ‘Activate?’ or turn the large FMS Knob to
highlight the ‘CRS’ field.
13) Turn the small FMS Knob to enter the desired course to the waypoint.
15) Press the ENT Key again to activate the Direct-to.
ACTIVATE A STORED FLIGHT PLAN
1)
Press the FPL Key on the MFD and turn the small FMS Knob to display the
Flight Plan Catalog Page.
2)
Press the FMS Knob to activate the cursor.
3)
Turn the large FMS Knob to highlight the desired flight plan
4)
Press the ACTIVE Softkey. The confirmation window is now displayed.
5)
With ‘OK’ highlighted, press the ENT Key to activate the flight plan. To cancel
the flight plan activation, turn the large FMS Knob to highlight ‘CANCEL’ and
press the ENT Key.
ACTIVATE A FLIGHT PLAN LEG
Appendix
Annun/Alerts
Abnormal
Operation
Additional
Features
Hazard
Avoidance
Procedures
Flight
Planning
14) Press the ENT Key to highlight ‘ACTIVATE?’.
1)
From the Active Flight Plan Page, press the FMS Knob to activate the cursor
and turn the large FMS Knob to highlight the desired waypoint.
2)
Press the ACT LEG Softkey.
OR
Index
Press the MENU Key, select the ‘Activate Leg’ option from the page menu
and press the ENT Key. This step must be used when activating a leg from
the PFD.
3)
16
With ‘Activate’ highlighted, press the ENT Key.
Garmin G1000 Cockpit Reference Guide for the Piper PA-44-180 Seminole
190-01462-00 Rev. A
GPS Navigation
Flight
Instruments
STOP NAVIGATING A FLIGHT PLAN
2)
Press the MENU Key to display the Page Menu Window.
3)
Turn the large FMS Knob to highlight ‘Delete Flight Plan’ and press the ENT
Key. With ‘OK’ highlighted, press the ENT Key to deactivate the flight plan.
This will not delete the stored flight plan, only the active flight plan.
VERTICAL NAVIGATION (VNAV)
Flight
Planning
NOTE: Temperature Compensated (TEMP COMP) altitudes are depicted as
slanted text.
GPS Nav
The navigation database only contains altitudes for procedures that call for “Cross
at” altitudes. If the procedure states “Expect to cross at,” the altitude is not in the
database. In this case the altitude may be entered manually.
Nav/Com/
XPDR/Audio
Press the FPL Key to display the Active Flight Plan Page.
EIS
1)
Procedures
Hazard
Avoidance
Large White
Text
Insertion
Point
Indicator
Additional
Features
Large Light
Blue Text
Small Light
Blue Text
Abnormal
Operation
Small Light
Blue Subdued
Text
Annun/Alerts
Small White Text
with Altitude
Restriction Bar
Appendix
Cross AT or ABOVE 5,000 ft
Cross AT 2,300 ft
Index
Cross AT or BELOW 3,000 ft
190-01462-00 Rev. A
Garmin G1000 Cockpit Reference Guide for the Piper PA-44-180 Seminole
17
Altitudes associated with approach procedures are “auto-designated”. This means
the system will automatically use the altitudes loaded with the approach for giving
vertical flight path guidance outside the FAF. Note these altitudes are displayed as
small light blue text.
Altitudes associated with arrival procedures are “manually-designated”. This
means the system will not use the altitudes loaded with the arrival for giving vertical
flight path guidance until designated to do so by the pilot. Note that these altitudes
are initially displayed as white text. These altitudes may be “designated” by placing
the cursor over the desired altitude and pressing the ENT Key. After designation, the
text changes to light blue.
Altitudes that have been designated for use in vertical navigation may also be
made “non-designated” by placing the cursor over the desired altitude and pressing
the CLR Key. The altitude is now displayed only as a reference. It will not be used
to give vertical flight path guidance. Other displayed altitudes may change due to
re-calculations or rendered invalid as a result of manually changing an altitude to a
non-designated altitude.
The system updates vertical path guidance continuously using ground speed and
the calculated distance to the Bottom of Descent (BOD). Due to turn anticipation
guidance (turn-smoothing), distance to the BOD can be affected by course changes
greater than approximately 5 degrees. Ground speed can be affected by factors such as
shifts in wind direction, aircraft power management, pitch angle, and course changes.
Abrupt and/or substantial changes to either the distance to the BOD, ground speed, or
both can cause similarly abrupt/substantial changes in vertical path guidance.
Because of turn-smoothing, changes to both distance to the BOD and ground speed
tend to be more extreme when the BOD is also a waypoint that marks a large course
change. These speed and distance changes will be accounted for in the computed
required vertical path and reflected in the vertical guidance indications.
Index
Appendix
Annun/Alerts
Abnormal
Operation
Additional
Features
Hazard
Avoidance
Procedures
Flight
Planning
GPS Nav
Nav/Com/
XPDR/Audio
EIS
Flight
Instruments
GPS Navigation
18
Garmin G1000 Cockpit Reference Guide for the Piper PA-44-180 Seminole
190-01462-00 Rev. A
GPS Navigation
Light Blue Text
Light Blue
Subdued Text
Large Text Altitude calculated by
the system estimating
the altitude of the
aircraft as it passes
over the navigation
point. This altitude
is provided as a
reference and is not
designated to be used
in determining vertical
flight path guidance.
Altitude has been
entered by the pilot.
Altitude is designated
for use in giving
vertical flight path
guidance. Altitude
does not match the
published altitude in
navigation database or
no published altitude
exists.
The system cannot
use this altitude in
determining vertical
flight path guidance.
Small Text Altitude is not
designated to be used
in determining vertical
flight path guidance.
Altitude has been
retrieved from the
navigation database
and is provided as a
reference.
Altitude is designated
for use in giving vertical
flight path guidance.
Altitude has been
retrieved from the
navigation database
or has been entered by
the pilot and matches
a published altitude
in the navigation
database.
The system cannot
use this altitude in
determining vertical
flight path guidance.
Flight
Instruments
White Text
EIS
Nav/Com/
XPDR/Audio
GPS Nav
Flight
Planning
Procedures
Hazard
Avoidance
Additional
Features
Abnormal
Operation
Annun/Alerts
Appendix
Index
190-01462-00 Rev. A
Garmin G1000 Cockpit Reference Guide for the Piper PA-44-180 Seminole
19
Index
Appendix
Annun/Alerts
Abnormal
Operation
Additional
Features
Hazard
Avoidance
Procedures
Flight
Planning
GPS Nav
Nav/Com/
XPDR/Audio
EIS
Flight
Instruments
GPS Navigation
Blank Page
20
Garmin G1000 Cockpit Reference Guide for the Piper PA-44-180 Seminole
190-01462-00 Rev. A
Flight Planning
Flight
Instruments
FLIGHT PLANNING
WEIGHT PLANNING
EIS
All procedures apply to the MFD unless otherwise stated.
Entering Weight Parameters
Procedures
Hazard
Avoidance
Turn the large FMS Knob to place the cursor in the ‘FUEL ON BOARD’ field.
3)
Turn the small FMS Knob to enter the desired fuel quantity.
4)
Press the ENT Key. The cursor is now in the ‘FUEL RESERVES’ field.
5)
Turn the small FMS Knob to enter the desired reserve fuel quantity.
6)
Press the FMS Knob to remove the cursor.
7)
Press the ENT Key.
Abnormal
Operation
2)
Additional
Features
Press the FMS Knob to activate the cursor.
Annun/Alerts
TRIP PLANNING
2)
Turn the small FMS Knob to select the Trip Planning Page.
3)
The current ‘PAGE MODE’ is displayed at the top of the page: ‘AUTOMATIC’
or ‘MANUAL’. To change the page mode, press the AUTO or MANUAL
Softkey.
21
Index
Turn the large FMS Knob to select the ‘AUX’ page group.
Appendix
1)
Garmin G1000 Cockpit Reference Guide for the Piper PA-44-180 Seminole
Flight
Planning
1)
190-01462-00 Rev. A
GPS Nav
Entering Fuel Parameters
Nav/Com/
XPDR/Audio
The Weight Planning Page is displayed after system power-up. If it is necessary to
return to this page, turn the large FMS Knob to select the ‘AUX’ page group. Turn the
small FMS Knob to select the Weight Planning Pge.
1) Press the EMPTY WT Softkey to place the cursor in the Basic Empty Weight
field.
2) Enter the desired aircraft empty weight.
3) Press the ENT Key. The cursor is now over the ‘PILOT & STORES’ field.
4) Enter the desired weight of Pilot & Stores.
5) Press the ENT Key.
6) Continue repeating these steps until all desired weights have been entered.
Flight Planning
Flight
Instruments
4)
For Direct-to planning:
a) Press the WPTS Softkey and verify that the starting waypoint field
indicates ‘P.POS’ (present position).
EIS
b) If necessary, press the MENU Key and select ‘Set WPT to Present
Position’ to display ‘P.POS’.
Nav/Com/
XPDR/Audio
c) Press the ENT Key and the flashing cursor moves to the ending
waypoint field.
GPS Nav
d) Enter the identifier of the ending waypoint and press the ENT Key to
accept the waypoint.
Or:
For point-to-point planning:
Flight
Planning
a) Enter the identifier of the starting waypoint.
Procedures
b) Once the waypoint’s identifier is entered, press the ENT Key to accept
the waypoint. The flashing cursor moves to the ending waypoint.
c) Again, enter the identifier of the ending waypoint.
d) Press the ENT Key to accept the waypoint.
Hazard
Avoidance
Or:
For flight plan leg planning:
Additional
Features
a) Press the FPL Softkey (at the bottom of the display).
b) Turn the small FMS Knob to select the desired flight plan (already
stored in memory), by number.
Annun/Alerts
d) Turn the small FMS Knob to select the desired leg of the flight plan, or
select ‘CUM’ to apply trip planning calculations to the entire flight plan.
Selecting ‘FPL 00’ displays the active flight plan. If an active flight plan
is selected, ‘REM’ will be an available option to display planning data
for the remainder of the flight plan.
Appendix
Abnormal
Operation
c) Turn the large FMS Knob to highlight the ‘LEG’ field.
NOTE: The page mode must be set to ‘MANUAL’ to perform the following
steps.
Index
5)
Turn the large FMS Knob to highlight the departure time (DEP TIME) field.
NOTE: The departure time on the Trip Planning Page is used for preflight
planning. Refer to the Utility Page for the actual flight departure time.
22
Garmin G1000 Cockpit Reference Guide for the Piper PA-44-180 Seminole
190-01462-00 Rev. A
Flight Planning
8)
The flashing cursor moves to the fuel flow field. Enter the fuel flow. Press
the ENT Key when finished. Note that in ‘AUTOMATIC’ page mode, fuel flow
is provided by the system.
9)
The flashing cursor moves to the fuel onboard field. Enter the fuel onboard.
Press the ENT Key when finished. Note that in ‘AUTOMATIC’ page mode, fuel
onboard is provided by the fuel totalizer.
Press the NEW Softkey. A waypoint is created at the current aircraft
position.
4)
Enter the desired waypoint name.
5)
Press the ENT Key.
6)
The cursor is now in the ‘WAYPOINT TYPE’ field. If desired, the waypoint
can be made temporary (deleted automatically when the system is turned
off). If the waypoint is to remain in the system, proceed to step 7.
190-01462-00 Rev. A
Garmin G1000 Cockpit Reference Guide for the Piper PA-44-180 Seminole
Index
3)
Appendix
Turn the small FMS Knob to select the User WPT Information Page.
Annun/Alerts
2)
Abnormal
Operation
Turn the large FMS Knob on the MFD to select the ‘WPT’ page group.
Additional
Features
1)
Hazard
Avoidance
CREATE A USER WAYPOINT DEFINED BY LATITUDE & LONGITUDE
Procedures
11) The flashing cursor moves to the altitude (IND ALTITUDE) field. Enter the
altitude. Press the ENT Key when finished. Note that in ‘AUTOMATIC’ page
mode, altitude is provided by the system.
12) The flashing cursor moves to the barometric setting (PRESSURE) field. Enter
the desired baro setting. Press the ENT Key when finished. Note that in
‘AUTOMATIC’ page mode, the baro setting is provided by the setting entered
on the PFD.
13) The flashing cursor moves to the air temperature (TOTAL AIR TEMP) field. Enter
the desired air temperature. Press the ENT Key when finished. Note that in
‘AUTOMATIC’ page mode, air temperature is provided by the system outside
air temperature.
Flight
Planning
10) The flashing cursor moves to the calibrated airspeed (CALIBRATED AS) field.
Enter the calibrated airspeed. Press the ENT Key when finished. Note that
in ‘AUTOMATIC’ page mode, calibrated airspeed is provided by the system.
GPS Nav
The flashing cursor moves to the ground speed (GS) field. Enter the ground
speed. Press the ENT Key when finished. Note that in ‘automatic’ page
mode, ground speed is provided by the system.
Nav/Com/
XPDR/Audio
7)
EIS
Enter the departure time. Press the ENT Key when finished. Departure time
may be entered in local or UTC time, depending upon system settings.
Flight
Instruments
6)
23
Flight Planning
Flight
Instruments
a) Turn the large FMS Knob one click to the left to highlight
‘TEMPORARY’.
7)
With the cursor in the ‘WAYPOINT TYPE’ field, turn the small FMS Knob to
display a list of waypoint types.
8)
Turn the small FMS Knob to select LAT/LON (latitude and longitude).
9)
Press the ENT Key.
CREATE A USER WAYPOINT DEFINED BY RADIALS FROM OTHER WAYPOINTS
Hazard
Avoidance
Procedures
Flight
Planning
GPS Nav
Nav/Com/
XPDR/Audio
EIS
b) Press the ENT Key to place a check-mark in the box. Turn the large
FMS Knob to place the cursor back in the ‘WAYPOINT TYPE’ field.
1)
Turn the large FMS Knob on the MFD to select the ‘WPT’ page group.
2)
Turn the small FMS Knob to select the User WPT Information Page.
3)
Press the NEW Softkey. A waypoint is created at the current aircraft
position.
4)
Enter the desired waypoint name.
5)
Press the ENT Key.
6)
The cursor is now in the ‘WAYPOINT TYPE’ field. If desired, the waypoint
can be made temporary (deleted automatically when the system is turned
off). If the waypoint is to remain in the system, proceed to step 7.
Additional
Features
a) Turn the large FMS Knob one click to the left to highlight
‘TEMPORARY’.
Annun/Alerts
Abnormal
Operation
b) Press the ENT Key to place a check-mark in the box. Turn the large
FMS Knob to place the cursor back in the ‘WAYPOINT TYPE’ field.
7)
With the cursor in the ‘WAYPOINT TYPE’ field, turn the small FMS Knob to
display a list of waypoint types.
8)
Turn the small FMS Knob to select RAD/RAD (radial/radial).
9)
Press the ENT Key.
Appendix
10) The cursor moves to the ‘REFERENCE WAYPOINTS’ field. With the first
waypoint name highlighted, use the FMS Knobs to enter the desired
waypoint name. Waypoints may also be selected as follows:
Index
a) When a flight plan is active, turning the small FMS Knob to the left will
display a list of the flight plan waypoints.
b) Turn the large FMS Knob to select the desired waypoint.
c) Press the ENT Key.
24
Garmin G1000 Cockpit Reference Guide for the Piper PA-44-180 Seminole
190-01462-00 Rev. A
Flight Planning
a) Turn the small FMS Knob to the left. Initially, a flight plan waypoint list
is displayed.
EIS
b) Turn the small FMS Knob to the right to display the ‘NRST’ airports to
the aircraft’s current position.
Flight
Instruments
Or:
Nav/Com/
XPDR/Audio
c) Turn the large FMS Knob to select the desired waypoint.
d) Press the ENT Key.
Or:
Flight
Planning
b) Turn the small FMS Knob to the right to display the ‘RECENT’
waypoints.
GPS Nav
a) Turn the small FMS Knob to the left. Initially, a flight plan waypoint list
is displayed.
c) Turn the large FMS Knob to select the desired waypoint.
Or:
b) Turn the small FMS Knob to the right to display the ‘USER’ waypoints.
Hazard
Avoidance
a) Turn the small FMS Knob to the left. Initially, a flight plan waypoint list
is displayed.
Procedures
d) Press the ENT Key.
c) Turn the large FMS Knob to select the desired waypoint.
12) Press the ENT Key.
13) Repeat step 10 to enter the next waypoint name.
15) Press the ENT Key.
Appendix
16) Press the FMS Knob to remove the flashing cursor.
Turn the large FMS Knob on the MFD to select the ‘WPT’ page group.
2)
Turn the small FMS Knob to select the User WPT Information Page.
190-01462-00 Rev. A
Garmin G1000 Cockpit Reference Guide for the Piper PA-44-180 Seminole
Index
CREATE A USER WAYPOINT DEFINED BY A RADIAL & DISTANCE FROM
ANOTHER WAYPOINT
1)
Annun/Alerts
14) Press the ENT Key. The cursor is displayed in the ‘RAD’ (radial) field for the
second waypoint. Enter the desired radial from the reference waypoint.
Abnormal
Operation
11) Press the ENT Key. The cursor is displayed in the ‘RAD’ (radial) field. Enter
the desired radial from the reference waypoint.
Additional
Features
d) Press the ENT Key.
25
3)
Press the NEW Softkey. A waypoint is created at the current aircraft
position.
4)
Enter the desired waypoint name.
5)
Press the ENT Key.
6)
The cursor is now in the ‘WAYPOINT TYPE’ field. If desired, the waypoint
can be made temporary (deleted automatically when the system is turned
off). If the waypoint is to remain in the system, proceed to step 7.
Nav/Com/
XPDR/Audio
EIS
Flight
Instruments
Flight Planning
GPS Nav
a) Turn the large FMS Knob one click to the left to highlight
‘TEMPORARY’.
Procedures
Flight
Planning
b) Press the ENT Key to place a check-mark in the box. Turn the large
FMS Knob to place the cursor back in the ‘WAYPOINT TYPE’ field.
7)
With the cursor in the ‘WAYPOINT TYPE’ field, turn the small FMS Knob to
display a list of waypoint types.
8)
Turn the small FMS Knob to select RAD/DIS (radial/distance).
9)
Press the ENT Key.
Hazard
Avoidance
10) The cursor moves to the ‘REFERENCE WAYPOINTS’ field. With the first
waypoint name highlighted, use the FMS Knobs to enter the desired
waypoint name. Waypoints may also be selected as follows:
Additional
Features
a) When a flight plan is active, turning the small FMS Knob to the left will
display a list of the flight plan waypoints.
b) Turn the large FMS Knob to select the desired waypoint.
c) Press the ENT Key.
Abnormal
Operation
Or:
Annun/Alerts
a) Turn the small FMS Knob to the left. Initially, a flight plan waypoint list
is displayed.
b) Turn the small FMS Knob to the right to display the ‘NRST’ airports to
the aircraft’s current position.
Appendix
c) Turn the large FMS Knob to select the desired waypoint.
d) Press the ENT Key.
Or:
Index
a) Turn the small FMS Knob to the left. Initially, a flight plan waypoint list
is displayed.
b) Turn the small FMS Knob to the right to display the ‘RECENT’
waypoints.
26
Garmin G1000 Cockpit Reference Guide for the Piper PA-44-180 Seminole
190-01462-00 Rev. A
Flight Planning
Flight
Instruments
c) Turn the large FMS Knob to select the desired waypoint.
d) Press the ENT Key.
Or:
c) Turn the large FMS Knob to select the desired waypoint.
d) Press the ENT Key.
Flight
Planning
12) Press the ENT Key.
13) The cursor is now displayed in the ‘DIS’ (distance) field. Enter the desired
distance from the reference waypoint.
Procedures
14) Press the ENT Key.
15) Press the FMS Knob to remove the flashing cursor.
2)
Press the ENT Key. The User Waypoint Information Page is displayed with
the captured position.
Additional
Features
Press the Joystick to activate the panning function and pan to the map
location of the desired user waypoint.
Hazard
Avoidance
CREATE A USER WAYPOINT USING THE MAP POINTER
1)
5)
If desired, define the type and location (i.e., LAT/LON, RAD/RAD or RAD/
DIS) of the waypoint.
6)
Press the ENT Key to accept the new waypoint.
190-01462-00 Rev. A
Garmin G1000 Cockpit Reference Guide for the Piper PA-44-180 Seminole
Index
Press the ENT Key to accept the selected name.
Appendix
4)
Annun/Alerts
Enter a user waypoint name (up to six characters).
Abnormal
Operation
NOTE: If the pointer has highlighted a map database feature, one of three
things happens upon pressing the ENT Key: 1) information about the selected
feature is displayed instead of initiating a new waypoint, 2) a menu pops up
allowing a choice between ‘Review Airspaces’ or ‘Create User Waypoint’, or 3)
a new waypoint is initiated with the default name being the selected map item.
3)
GPS Nav
11) Press the ENT Key. The cursor is displayed in the ‘RAD’ (radial) field. Enter
the desired radial from the reference waypoint.
Nav/Com/
XPDR/Audio
b) Turn the small FMS Knob to the right to display the ‘USER’ waypoints.
EIS
a) Turn the small FMS Knob to the left. Initially, a flight plan waypoint list
is displayed.
27
If desired, change the storage method of the waypoint to “TEMPORARY” or
“NORMAL” by moving the cursor to “TEMPORARY” and pressing the ENT
Key to check or uncheck the box.
8)
Press the FMS Knob to remove the flashing cursor.
9)
Press the GO BACK Softkey to return to the map page.
Flight
Planning
Procedures
1)
Turn the large FMS Knob to select the ‘WPT’ page group.
2)
Turn the small FMS Knob to select the User WPT Information Page.
3)
Press the FMS Knob to activate the cursor.
4)
Turn the large FMS Knob to the place the cursor in the ‘USER WAYPOINT LIST’
field.
5)
Turn the small FMS Knob to highlight the desired waypoint.
6)
Press the DELETE Softkey.
7)
The message ‘Would you like to delete the user waypoint?’ is displayed. With
‘YES’ highlighted, press the ENT Key.
CREATE A FLIGHT PLAN
NOTE: When creating a flight plan in the Active Flight Plan Window, the first
leg is activated automatically after it is created.
Additional
Features
Hazard
Avoidance
7)
DELETE A USER WAYPOINT
GPS Nav
Nav/Com/
XPDR/Audio
EIS
Flight
Instruments
Flight Planning
Index
Appendix
Annun/Alerts
Abnormal
Operation
Creating an active flight plan:
1) Press the FPL Key.
2) Press the FMS Knob to activate the cursor (only on MFD).
3) Turn the small FMS Knob to display the Waypoint Information Window.
(Turning it clockwise displays a blank Waypoint Information Window,
turning it counter-clockwise displays the Waypoint Information Window
with a waypoint selection submenu allowing selection of active flight plan,
nearest, recent, user, or airway waypoints).
4) Enter the identifier, facility, or city name of the departure waypoint or select
a waypoint from the submenu of waypoints and press the ENT Key. The
active flight plan is modified as each waypoint is entered.
5) Repeat step numbers 3 and 4 to enter each additional flight plan waypoint.
6) When all waypoints have been entered, press the FMS Knob to remove the
cursor.
28
Garmin G1000 Cockpit Reference Guide for the Piper PA-44-180 Seminole
190-01462-00 Rev. A
Flight Planning
Press the FMS Knob to activate the cursor.
5)
Turn either FMS Knob to highlight an empty or existing flight plan.
6)
Press the IMPORT Softkey.
Abnormal
Operation
4)
Additional
Features
Turn the small FMS Knob to select the Flight Plan Catalog Page.
Hazard
Avoidance
3)
Procedures
Press the FPL Key on the MFD to display the Active Flight Plan Page on the
MFD.
Flight
Planning
2)
GPS Nav
Insert the SD card containing the flight plan in the top card slot on the MFD.
Nav/Com/
XPDR/Audio
1)
EIS
IMPORT A FLIGHT PLAN FROM AN SD CARD
Flight
Instruments
Creating a stored flight plan:
1) Press the FPL Key.
2) Turn the small FMS Knob clockwise to display the Flight Plan Catalog Page.
3) Press the NEW Softkey; or press the MENU Key, highlight ‘Create New
Flight Plan’, and press the ENT Key to display a blank flight plan for the
first empty storage location.
4) Turn the small FMS Knob to display the Waypoint Information Window.
(Turning it clockwise displays a blank Waypoint Information Window,
turning it counter-clockwise displays the Waypoint Information Window
with a waypoint selection submenu allowing selection of active flight plan,
nearest, recent, user, or airway waypoints).
5) Enter the identifier, facility, or city name of the departure waypoint or select
a waypoint from the submenu of waypoints and press the ENT Key.
6) Repeat step numbers 4 and 5 to enter each additional flight plan waypoint.
7) When all waypoints have been entered, press the FMS Knob to return to
the Flight Plan Catalog Page. The new flight plan is now in the list.
Annun/Alerts
If an empty flight plan is selected, a list of the available flight plans on the
SD card will be displayed.
Or:
Garmin G1000 Cockpit Reference Guide for the Piper PA-44-180 Seminole
29
Index
190-01462-00 Rev. A
Appendix
If an existing flight plan is selected, an ‘Overwrite existing flight plan? OK
or CANCEL’ prompt is displayed. Press the ENT Key to choose to overwrite
the selected flight plan and see a list of the available flight plans on the SD
card. If overwriting the existing flight plan is not desired, select ‘CANCEL’
using the FMS Knob, press the ENT Key, select another existing or empty
flight plan, and again press the IMPORT Softkey.
7)
Turn the small FMS Knob to highlight the desired flight plan for importing.
8)
Press the ENT Key.
INSERT A WAYPOINT IN THE ACTIVE FLIGHT PLAN
Flight
Planning
GPS Nav
Nav/Com/
XPDR/Audio
EIS
Flight
Instruments
Flight Planning
1)
Press the FPL Key to display the active flight plan.
2)
If necessary, press the FMS Knob to activate the cursor.
3)
Turn the large FMS Knob to highlight the desired flight plan waypoint. The
new waypoint is inserted before the highlighted waypoint (shown by the
insertion point indicator).
4)
Turn the small FMS Knob. The Waypoint Information Window is now
displayed.
5)
Enter the new flight plan waypoint by one of the following:
a) Enter the user waypoint identifier, facility, or city.
Procedures
b) Press the ENT Key.
Or:
Hazard
Avoidance
a) Turn the small FMS Knob to the left. Initially, a flight plan waypoint list
is displayed.
b) Turn the small FMS Knob to the right to display the ‘NRST’ airports to
the aircraft’s current position.
Additional
Features
c) Turn the large FMS Knob to select the desired waypoint.
d) Press the ENT Key.
Abnormal
Operation
Or:
a) Turn the small FMS Knob to the left. Initially, a flight plan waypoint list
is displayed.
Annun/Alerts
b) Turn the small FMS Knob to the right to display the ‘RECENT’
waypoints.
c) Turn the large FMS Knob to select the desired waypoint.
Appendix
d) Press the ENT Key.
Or:
Index
a) Turn the small FMS Knob to the left. Initially, a flight plan waypoint list
is displayed.
b) Turn the small FMS Knob to the right to display the ‘USER’ waypoints.
30
Garmin G1000 Cockpit Reference Guide for the Piper PA-44-180 Seminole
190-01462-00 Rev. A
Flight Planning
Flight
Instruments
c) Turn the large FMS Knob to select the desired user waypoint.
d) Press the ENT Key.
6)
Press the ENT Key again to “accept” the waypoint.
EIS
ENTER AN AIRWAY IN A FLIGHT PLAN
Turn the small FMS Knob one click clockwise and press the LD AIRWY
Softkey, or press the MENU Key and press “Load Airway”. The Select
Airway Page is displayed. The LD AIRWY Softkey or the “Load Airway”
menu item is available only when an acceptable airway entry waypoint has
been chosen (the waypoint ahead of the cursor position as indicated by the
insertion point indicator).
5)
Turn the FMS Knob to select the desired airway from the list, and press the
ENT Key. Low altitude airways are shown first in the list, followed by “all”
altitude airways, and then high altitude airways.
6)
Turn the FMS Knob to select the desired airway exit point from the list, and
press the ENT Key. ‘LOAD?’ is highlighted.
7)
Press the ENT Key. The system returns to editing the flight plan with the
new airway inserted.
Abnormal
Operation
4)
USER-DEFINED HOLDING PATTERNS
Press the FPL Key to display the Active Flight Plan Page (MFD) or the Active
Flight Plan Window (PFD).
2)
Press the FMS Knob to activate the cursor (not required on the PFD) and
turn the large FMS Knob to highlight the waypoint for the hold.
Garmin G1000 Cockpit Reference Guide for the Piper PA-44-180 Seminole
Index
1)
Appendix
Creating a user-defined hold at an active flight plan waypoint:
Annun/Alerts
A holding pattern can be defined at any active flight plan waypoint, or at the aircraft
present position.
190-01462-00 Rev. A
Additional
Features
Turn the large FMS Knob to highlight the waypoint after the desired
airway entry point. The airway is inserted before the highlighted waypoint
(as shown by the insertion point indicator). If this waypoint is not a valid
airway entry point, a valid entry point should be entered at this time.
Hazard
Avoidance
3)
Procedures
Press the FMS Knob to activate the cursor (not required on the PFD).
Flight
Planning
2)
GPS Nav
Press the FPL Key.
Nav/Com/
XPDR/Audio
1)
31
Flight
Planning
GPS Nav
Nav/Com/
XPDR/Audio
EIS
Flight
Instruments
Flight Planning
3)
Press the MENU Key, highlight ‘Hold At Waypoint’, and press the ENT Key.
The HOLD AT window appears with the course field highlighted.
4)
Use the FMS Knobs to edit the entry course, and press the ENT Key.
5)
Use the small FMS Knob to select ‘INBOUND’ or ‘OUTBOUND’ course
direction, and press the ENT Key.
6)
Use the small FMS Knob to select ‘TIME’ or ‘DIST’ length mode, and press
the ENT Key.
7)
Use the FMS Knobs to edit the length, and press the ENT Key.
8)
Use the small FMS Knob to select ‘RIGHT’ or ‘LEFT’ turn direction, and
press the ENT Key.
9)
Use the FMS Knobs to edit the Expect Further Clearance Time (EFC TIME),
and press the ENT Key.
Procedures
10) Press the ENT Key while ‘LOAD?’ is highlighted to add the hold into the
flight plan.
Index
Appendix
Annun/Alerts
Abnormal
Operation
Additional
Features
Hazard
Avoidance
Creating a user-defined hold at the aircraft present position:
32
1)
Press the FPL Key to display the Active Flight Plan Page (MFD) or the Active
Flight Plan Window (PFD).
2)
Press the MENU Key, highlight ‘Hold At Present Position’, and press the
ENT Key. The HOLD AT window appears with the course field highlighted.
3)
Use the FMS Knobs to edit the entry course, and press the ENT Key.
4)
Use the small FMS Knob to select ‘INBOUND’ or ‘OUTBOUND’ course
direction, and press the ENT Key.
5)
Use the small FMS Knob to select ‘TIME’ or ‘DIST’ length mode, and press
the ENT Key.
6)
Use the FMS Knobs to edit the length, and press the ENT Key.
7)
Use the small FMS Knob to select ‘RIGHT’ or ‘LEFT’ turn direction, and
press the ENT Key.
8)
Use the FMS Knobs to edit the Expect Further Clearance Time (EFC TIME),
and press the ENT Key.
9)
Press the ENT Key while ‘ACTIVATE?’ is highlighted to create an Offroute
Direct-to hold waypoint and activate the hold.
Garmin G1000 Cockpit Reference Guide for the Piper PA-44-180 Seminole
190-01462-00 Rev. A
Flight Planning
Flight
Instruments
Creating a user-defined hold at a Direct To waypoint:
Press a Direct-to Key and set up the Direct To waypoint as desired, but
select ‘HOLD?’ instead of ‘ACTIVATE?’ when finished (MFD or PFD).
2)
Use the FMS Knobs to edit the entry course, and press the ENT Key.
3)
Use the small FMS Knob to select ‘INBOUND’ or ‘OUTBOUND’ course
direction, and press the ENT Key.
4)
Use the small FMS Knob to select ‘TIME’ or ‘DIST’ length mode, and press
the ENT Key.
5)
Use the FMS Knobs to edit the length, and press the ENT Key.
6)
Use the small FMS Knob to select ‘RIGHT’ or ‘LEFT’ turn direction, and
press the ENT Key.
7)
Use the FMS Knobs to edit the Expect Further Clearance Time (EFC TIME),
and press the ENT Key.
8)
Press the ENT Key while ‘ACTIVATE?’ is highlighted to activate the Direct To
with the user-defined hold defined at the Direct To waypoint.
EIS
1)
GPS Nav
Press the CLR Key. A ‘Remove Holding Pattern?’ confirmation window is
displayed.
4)
Select ‘OK’ and press the ENT Key. The holding pattern is removed from
the active flight plan. Select ‘CANCEL’ and press the ENT Key to cancel the
removal of the holding pattern.
Abnormal
Operation
3)
3)
Press the ENT Key. The holding pattern is removed.
190-01462-00 Rev. A
Garmin G1000 Cockpit Reference Guide for the Piper PA-44-180 Seminole
Index
Press the MENU Key to display the PAGE MENU with the cursor on the
‘Cancel Direct To NAV’ selection.
Appendix
2)
Annun/Alerts
Removing a user-defined hold (created at the aircraft present position
or at a Direct-To waypoint):
Press the Direct To Key to display the DIRECT TO Window (PFD or MFD).
Additional
Features
Press the FMS Knob to activate the cursor (not required on the PFD) and
turn the large FMS Knob to highlight the HOLD waypoint.
Hazard
Avoidance
2)
Procedures
Press the FPL Key to display the Active Flight Plan Page (MFD) or the Active
Flight Plan Window (PFD).
Flight
Planning
1)
1)
Nav/Com/
XPDR/Audio
Removing a user-defined hold (created at an active flight plan
waypoint):
33
INVERT AN ACTIVE FLIGHT PLAN
GPS Nav
Nav/Com/
XPDR/Audio
EIS
Flight
Instruments
Flight Planning
1)
Press the FPL Key to display the active flight plan.
2)
Press the MENU Key to display the Page Menu.
3)
Turn the large FMS Knob to highlight ‘Invert Flight Plan’.
4)
Press the ENT Key. The original flight plan remains intact in its flight plan
catalog storage location.
5)
With ‘OK’ highlighted, press the ENT Key to invert the flight plan.
REMOVE A DEPARTURE, ARRIVAL, APPROACH, OR AIRWAY FROM A FLIGHT
PLAN
Flight
Planning
1)
Or, for a stored flight plan:
Procedures
a) Press the MFD FPL Key and turn the small FMS Knob to select the
Flight Plan Catalog Page.
b) Press the FMS Knob to activate the cursor.
Hazard
Avoidance
c) Turn the large FMS Knob to highlight the desired flight plan.
Abnormal
Operation
Additional
Features
d) Press the EDIT Softkey.
2)
Turn the large FMS Knob to highlight the title for the approach, departure,
arrival, or airway to be deleted. Titles appear in white directly above the
procedure’s waypoints.
3)
Press the CLR Key to display a confirmation window.
4)
With ‘OK’ highlighted, press the ENT Key to remove the selected procedure
or airway.
STORE A FLIGHT PLAN
1)
After creating a flight plan on either the PFD or MFD, it may be saved by
pressing the MENU Key.
2)
Turn the large FMS Knob to highlight ‘Store Flight Plan’ and press the ENT Key.
3)
With ‘OK’ highlighted, press the ENT Key to store the flight plan.
Index
Appendix
Annun/Alerts
Press the FPL Key to display the active flight plan. Press the FMS Knob to
activate the cursor.
34
Garmin G1000 Cockpit Reference Guide for the Piper PA-44-180 Seminole
190-01462-00 Rev. A
Flight Planning
Press the FPL Key for the MFD and turn the small FMS Knob to display the
Flight Plan Catalog Page.
2)
Press the FMS Knob to activate the cursor.
3)
Turn the large FMS Knob to highlight the desired flight plan.
4)
Press the EDIT Softkey.
5)
Turn the large FMS Knob to place the cursor in the desired location.
6)
Enter the changes, then press the ENT Key.
7)
Press the FMS Knob to return to the Flight Plan Catalog Page.
EIS
1)
Nav/Com/
XPDR/Audio
GPS Nav
Press the FPL Key to display the active flight plan. Press the FMS Knob to
activate the cursor.
Procedures
Or, for a stored flight plan:
Flight
Planning
DELETE A WAYPOINT FROM THE FLIGHT PLAN
1)
Flight
Instruments
EDIT A STORED FLIGHT PLAN
a) Press the FPL Key of the MFD and turn the small FMS Knob to select
the Flight Plan Catalog Page.
Hazard
Avoidance
b) Press the FMS Knob to activate the cursor.
c) Turn the large FMS Knob to highlight the desired flight plan.
Additional
Features
d) Press the EDIT Softkey.
3)
Press the CLR Key to display a ‘REMOVE (Wpt Name)?’ confirmation
window.
4)
With ‘OK’ highlighted, press the ENT Key to remove the waypoint. To cancel
the delete request, turn the large FMS Knob to highlight ‘CANCEL’ and press
the ENT Key.
5)
Once all changes have been made, press the FMS Knob to remove the
cursor.
Annun/Alerts
Turn the large FMS Knob to highlight the waypoint to be deleted.
Abnormal
Operation
2)
Appendix
Index
190-01462-00 Rev. A
Garmin G1000 Cockpit Reference Guide for the Piper PA-44-180 Seminole
35
INVERT AND ACTIVATE A STORED FLIGHT PLAN
Press the FPL Key for the MFD.
2)
Turn the small FMS Knob to select the Flight Plan Catalog Page.
3)
Press the FMS Knob to activate the cursor.
4)
Turn the large FMS Knob to highlight the desired flight plan.
5)
Press the INVERT Softkey. ‘Invert and activate stored flight plan?’ is
displayed.
6)
With ‘OK’ highlighted, press the ENT Key. The selected flight plan is now
inverted and activated. The original flight plan remains intact in its flight plan
catalog storage location.
Hazard
Avoidance
1)
Press the FPL Key for the MFD.
2)
Turn the small FMS Knob to select the Flight Plan Catalog Page.
3)
Press the FMS Knob to activate the cursor.
4)
Turn the large FMS Knob to highlight the flight plan to be copied.
5)
Press the COPY Softkey. A ‘Copy to flight plan #?’ confirmation window is
displayed.
6)
With ‘OK’ highlighted, press the ENT Key to copy the flight plan. To cancel,
turn the large FMS Knob to highlight ‘CANCEL’ and press the ENT Key.
DELETE A FLIGHT PLAN
1)
Press the FPL Key for the MFD.
2)
Turn the small FMS Knob to select the Flight Plan Catalog Page.
3)
Press the FMS Knob to activate the cursor.
4)
Turn the large FMS Knob to highlight the flight plan to be deleted.
5)
Press the DELETE Softkey. A ‘Delete flight plan #?’ confirmation window is
displayed.
6)
With ‘OK’ highlighted, press the ENT Key to delete the flight plan. To cancel,
turn the large FMS Knob to highlight ‘CANCEL’ and press the ENT Key.
Index
Appendix
Annun/Alerts
Abnormal
Operation
Additional
Features
1)
COPY A FLIGHT PLAN
Procedures
Flight
Planning
GPS Nav
Nav/Com/
XPDR/Audio
EIS
Flight
Instruments
Flight Planning
36
Garmin G1000 Cockpit Reference Guide for the Piper PA-44-180 Seminole
190-01462-00 Rev. A
Flight Planning
Flight
Instruments
GRAPHICAL FLIGHT PLAN CREATION
The default insertion point is at the end of the flight plan. If the selected
waypoint is to be placed anywhere other than the end of the flight plan,
press the FMS Knob to activate the cursor. Waypoints are inserted ABOVE
the cursor (as indicated by the insertion point indicator). Turn the large FMS
Knob to select the desired insertion point.
4)
Press the LD WPT Softkey. The selected waypoint is inserted at the selected
point. The default user waypoint naming is USR000, USR001, USR002, and
so on.
5)
To change the user waypoint name, follow the procedure for modifying a user
waypoint.
EXPORT A FLIGHT PLAN TO AN SD CARD
2)
Press the FPL Key on the Control Unit to display the Active Flight Plan Page
on the MFD.
3)
Turn the small FMS Knob to select the Flight Plan Catalog Page.
4)
Press the FMS Knob to activate the cursor.
5)
Turn the large FMS Knob to highlight the flight plan to be exported.
6)
Press the EXPORT Softkey.
7)
Press the ENT Key to confirm the export.
Additional
Features
Insert the SD card into the top card slot on the MFD.
Hazard
Avoidance
1)
Procedures
3)
Flight
Planning
Press the Joystick to activate the map pointer. Use the Joystick to move
the pointer to the desired point on the map to be inserted as a waypoint in
the flight plan.
GPS Nav
2)
Nav/Com/
XPDR/Audio
Press the FPL Key to display the Active Flight Plan Page on the MFD.
EIS
1)
Abnormal
Operation
Annun/Alerts
Appendix
Index
190-01462-00 Rev. A
Garmin G1000 Cockpit Reference Guide for the Piper PA-44-180 Seminole
37
Index
Appendix
Annun/Alerts
Abnormal
Operation
Additional
Features
Hazard
Avoidance
Procedures
Flight
Planning
GPS Nav
Nav/Com/
XPDR/Audio
EIS
Flight
Instruments
Flight Planning
Blank Page
38
Garmin G1000 Cockpit Reference Guide for the Piper PA-44-180 Seminole
190-01462-00 Rev. A
Procedures
Flight
Instruments
PROCEDURES
LOAD AND ACTIVATE A DEPARTURE PROCEDURE
EIS
Press the ENT Key. The cursor is displayed in the ‘DEPARTURE’ field with a
list of available departures.
4)
Turn the large FMS Knob to highlight the desired departure.
5)
Press the ENT Key. A list of runways may be displayed for the departure. If
so, turn either FMS Knob to select the desired runway.
6)
Press the ENT Key. The cursor is displayed in the ‘TRANSITION’ field with a
list of available transitions.
7)
Turn the large FMS Knob to highlight the desired transition.
8)
Press the ENT Key.
9)
With ‘LOAD?’ highlighted, press the ENT Key. The departure is active when
the flight plan is active.
ACTIVATE A DEPARTURE LEG
Press the FPL Key for the MFD to display the active flight plan.
2)
Press the FMS Knob to activate the cursor.
3)
Turn the large FMS Knob to highlight the desired waypoint within the
departure.
4)
Press the ACT LEG Softkey. A confirmation window showing the selected
leg is displayed.
5)
With ‘ACTIVATE’ highlighted, press the ENT Key.
Additional
Features
1)
Annun/Alerts
Appendix
Press the PROC Key.
2)
Turn the large FMS Knob to highlight ‘SELECT ARRIVAL’.
3)
Press the ENT Key. The cursor is displayed in the ‘ARRIVAL’ field with a list
of available arrivals.
39
Index
1)
Garmin G1000 Cockpit Reference Guide for the Piper PA-44-180 Seminole
Abnormal
Operation
LOAD AN ARRIVAL PROCEDURE
190-01462-00 Rev. A
Hazard
Avoidance
3)
Procedures
Turn the large FMS Knob to highlight ‘SELECT DEPARTURE’.
Flight
Planning
2)
GPS Nav
Press the PROC Key.
Nav/Com/
XPDR/Audio
1)
Nav/Com/
XPDR/Audio
EIS
Flight
Instruments
Procedures
4)
Turn the large FMS Knob to highlight the desired arrival.
5)
Press the ENT Key. A list of transitions is displayed for the selected arrival.
6)
Turn either FMS Knob to select the desired transition.
7)
Press the ENT Key. A list of runways may be displayed for the selected
arrival.
8)
Turn the large FMS Knob to highlight the desired runway.
9)
Press the ENT Key.
10) With ‘LOAD?’ highlighted, press the ENT Key.
GPS Nav
11) The arrival becomes part of the active flight plan.
1)
Press the FPL Key to display the active flight plan.
2)
Press the FMS Knob to activate the cursor.
3)
Turn the large FMS Knob to highlight the desired waypoint within the
arrival.
4)
Press the ACT LEG Softkey. A confirmation window showing the selected
leg is displayed.
5)
With ‘ACTIVATE’ highlighted, press the ENT Key.
LOAD AND/OR ACTIVATE AN APPROACH PROCEDURE
NOTE: If certain GPS parameters (SBAS, RAIM, etc.) are not available, some
published approach procedures for the desired airport may not be displayed
in the list of available approaches.
Appendix
Annun/Alerts
Abnormal
Operation
Additional
Features
Hazard
Avoidance
Procedures
Flight
Planning
ACTIVATE AN ARRIVAL LEG
1)
Press the PROC Key.
2)
Turn the large FMS Knob to highlight ‘SELECT APPROACH’.
3)
Select the airport and approach:
a) Use the FMS Knob to select an airport and press the ENT Key.
b) Select an approach from the list and press the ENT Key.
Index
Or:
40
Garmin G1000 Cockpit Reference Guide for the Piper PA-44-180 Seminole
190-01462-00 Rev. A
Procedures
EIS
b) Use the FMS Knob to enter the approach channel number, and press
the ENT Key to accept the approach channel number. The airport and
approach are selected.
Flight
Instruments
a) If necessary, push the FMS Knob to exit the approach list, and use the
large FMS Knob to move the cursor to the APPROACH CHANNEL field.
A list of available transitions for the selected approach procedure is now
displayed.
5)
Turn either FMS Knob to select the desired transition. The “Vectors”
option assumes vectors will be received to the final course segment of
the approach and will provide navigation guidance relative to the final
approach course.
6)
Press the ENT Key. The cursor moves to the MINIMUMS field.
7)
If desired, the DA/MDA for the selected approach procedure may be
entered and displayed on the PFD. Turn the small FMS Knob in the
direction of the green arrow to change the display from OFF to BARO, or
TEMP COMP.
8)
Press the ENT Key. The cursor moves to the altitude field. Turn the small
FMS Knob to enter the published DA/MDA for the selected approach
procedure.
9)
Press the ENT Key. If BARO, or OFF was selected in step 8, proceed to
step 11. If TEMP COMP was selected in step 8, the cursor moves to the
‘TEMP AT....” field. Turn the small FMS Knob to enter the temperature at
the destination airport. The temperature compensated altitude minimum is
displayed below the previously enter minimum altitude value.
Nav/Com/
XPDR/Audio
4)
GPS Nav
Flight
Planning
Procedures
Additional
Features
Abnormal
Operation
Annun/Alerts
11) Turn the large FMS Knob to select either ‘LOAD?’ or ‘ACTIVATE?’.
Hazard
Avoidance
10) Press the ENT Key. ‘LOAD? or ACTIVATE?’ is now displayed with ‘LOAD?’
highlighted.
Appendix
Selecting ‘LOAD?’ enters the selected approach procedure into the active
flight plan, but is not currently active. Selecting ‘ACTIVATE?’ enters the
selected approach procedure into the active flight plan and activates the
first leg of the approach.
12) Press the ENT Key.
Index
190-01462-00 Rev. A
Garmin G1000 Cockpit Reference Guide for the Piper PA-44-180 Seminole
41
ACTIVATE AN APPROACH IN THE ACTIVE FLIGHT PLAN
Procedures
Flight
Planning
2)
Turn the large FMS Knob to highlight ‘ACTIVATE APPROACH’.
3)
Press the ENT Key.
1)
Press the PROC Key.
2)
Turn the large FMS Knob to highlight ‘ACTIVATE VECTOR-TO-FINAL’.
3)
Press the ENT Key.
4)
The final approach course becomes the active leg.
ACTIVATE A MISSED APPROACH IN THE ACTIVE FLIGHT PLAN
Hazard
Avoidance
Additional
Features
Press the PROC Key.
1)
Press the PROC Key.
2)
Turn the large FMS Knob to highlight ‘ACTIVATE MISSED APPROACH’.
3)
Press the ENT Key. A confirmation window is displayed.
4)
With ‘ACTIVATE’ highlighted, press the ENT Key.
Or:
Press the Go-around Switch.
TEMPERATURE COMPENSATED ALTITUDE
When temperature compensated altitude is enabled for the loaded approach, the
altitudes associated with the approach waypoints are displayed in slanted text.
Appendix
Annun/Alerts
Abnormal
Operation
1)
ACTIVATE A VECTOR TO FINAL APPROACH FIX
GPS Nav
Nav/Com/
XPDR/Audio
EIS
Flight
Instruments
Procedures
Index
Altitudes Displayed Without
Temperature Compensation
42
Altitudes Displayed With
Temperature Compensation
Garmin G1000 Cockpit Reference Guide for the Piper PA-44-180 Seminole
190-01462-00 Rev. A
Procedures
EIS
Use the small FMS Knob to select the temperature at the <airport>. The
compensated altitude is computed as the temperature is selected.
Press the ENT Key. ‘ACTIVATE COMPENSATION?’ is highlighted.
6)
Press the ENT Key. The compensated altitudes for the approach are
GPS Nav
5)
Nav/Com/
XPDR/Audio
4)
Flight
Instruments
Enabling temperature compensated altitude:
1) From the Active Flight Plan Page, press the MENU Key. The Page Menu is
displayed.
2) Turn the FMS Knob to highlight ‘Temperature Compensation’.
3) Press the ENT Key. The TEMPERATURE COMPENSATION Window is
displayed.
shown in the flight plan.
Flight
Planning
Hazard
Avoidance
Press the ENT Key. The temperature compensated altitude at the FAF
is cancelled.
Additional
Features
5)
Procedures
Disabling temperature compensated altitude:
1) From the Active Flight Plan Page, press the MENU Key. The Page Menu is
displayed.
2) Turn the FMS Knob to highlight ‘Temperature Compensation’.
3) Press the ENT Key. The TEMPERATURE COMPENSATION Window is
displayed.
4) Press the ENT Key. ‘CANCEL COMPENSATION?’ is highlighted.
Abnormal
Operation
Annun/Alerts
Appendix
Index
190-01462-00 Rev. A
Garmin G1000 Cockpit Reference Guide for the Piper PA-44-180 Seminole
43
Index
Appendix
Annun/Alerts
Abnormal
Operation
Additional
Features
Hazard
Avoidance
Procedures
Flight
Planning
GPS Nav
Nav/Com/
XPDR/Audio
EIS
Flight
Instruments
Procedures
Blank Page
44
Garmin G1000 Cockpit Reference Guide for the Piper PA-44-180 Seminole
190-01462-00 Rev. A
Hazard Avoidance
Flight
Instruments
HAZARD AVOIDANCE
Customizing THE HAZARD DISPLAYS ON THE NAVIGATION MAP
EIS
2)
Press the ENT Key. The Map Setup Menu is displayed. Turn the small FMS
Knob to select ‘Weather’ to customize the display of weather features.
Select ‘Traffic’ to customize the display of traffic.
3)
Press the small FMS Knob to return to the Navigation Map Page.
Flight
Planning
SIRIUSXM WEATHER (OPTIONAL)
Press the NEXRAD or XM LTNG Softkey to display the desired weather.
Press the applicable softkey again to remove weather data from the
Navigation Map Page.
Annun/Alerts
2)
Abnormal
Operation
Press the MAP Softkey.
2)
Turn the small FMS Knob to select the Airport Information Page.
3)
Press the WX Softkey to display METAR and TAF text (METAR and TAF
information is updated every 12 minutes).
190-01462-00 Rev. A
Garmin G1000 Cockpit Reference Guide for the Piper PA-44-180 Seminole
Index
Turn the large FMS Knob to select the WPT Page Group.
Appendix
Display METAR and TAF information on the Airport Information Page
1)
Additional
Features
Displaying SiriusXM Weather on the Navigation Map Page
Hazard
Avoidance
WARNING: Do not use the indicated data link weather product age to
determine the age of the weather information shown by the data link weather
product. Due to time delays inherent in gathering and processing weather
data for data link transmission, the weather information shown by the data
link weather product may be significantly older than the indicated weather
product age.
Procedures
WARNING: Do not use data link weather information for maneuvering in,
near or around areas of hazardous weather. Information contained within data
link weather products may not accurately depict current weather conditions.
1)
GPS Nav
With the Navigation Map Page displayed, press the MENU Key to display
the Navigation Map Page Menu. The cursor flashes on the ‘Map Setup’
option.
Nav/Com/
XPDR/Audio
1)
45
Hazard Avoidance
Nav/Com/
XPDR/Audio
EIS
Flight
Instruments
Displaying Weather on the SiriusXM Weather Data Link Page
1)
Turn the large FMS Knob to select the Map Page Group.
2)
Turn the small FMS Knob to select the SiriusXM Weather Data Link Page.
3)
Press the available softkeys to select the desired SiriusXM Weather product.
4)
Press the LEGEND Softkey to view the legends for the selected products. If
necessary, turn either FMS Knob to scroll through the list. Press the small
FMS Knob or the ENT Key to return to the map.
Flight
Planning
GPS Nav
Map Panning Information – SiriusXM Weather Data Link Page
1)
Push in the Joystick to display the panning arrow.
2)
Move the Joystick to place the panning arrow on AIRMETs, TFRs, METARs,
or SIGMETs.
3)
Press the ENT Key to display pertinent information for the selected product.
Hazard
Avoidance
Procedures
Note that pressing the ENT Key when panning over an AIRMET or a
SIGMET displays an information box that shows the text of the report.
Panning over an airport with METAR information does not display more
information but allows the user to press the ENT Key and select that
Airport’s Information Page to display the text of the report. Pressing the
ENT Key when panning over a TFR displays TFR specific information.
Appendix
Annun/Alerts
Abnormal
Operation
Additional
Features
Enabling/disabling winds aloft data display in Profile View:
1)
Select the Navigation Map Page.
2)
Press the MENU Key.
3)
With Map Setup highlighted, press the ENT Key
4)
Turn the small FMS Knob to select the Profile Group and press the ENT Key
5)
Turn the large FMS Knob to select ‘Profile Winds’.
6)
7)
Turn the small FMS Knob to select ‘On’ or ‘Off’.
Press the FMS Knob or CLR Key to return to the Navigation Map Page with
the changed settings.
Index
NOTE: NEXRAD data cannot be displayed at the same time as terrain, echo
tops, turbulence, or icing data is displayed.
46
Garmin G1000 Cockpit Reference Guide for the Piper PA-44-180 Seminole
190-01462-00 Rev. A
Hazard Avoidance
Wx Product
Status Icons
Flight
Instruments
SiriusXM Weather Products and Symbols
Description
EIS
NEXRAD - Available for the US and Canada. The age of the displayed data
for each is shown at the right.
Nav/Com/
XPDR/Audio
ECHO TOP - The age of the displayed data is shown at the right. Not
displayed when CLOUD TOP is displayed.
GPS Nav
CLOUD TOP - The age of the displayed data is shown at the right. Not
displayed when ECHO TOP is displayed.
XM LIGHTNING - The age of the displayed data is shown at the right.
Flight
Planning
CELL MOVEMENT - The age of the displayed data is shown at the right.
Additional
Features
SURFACE ANALYSIS with CITY FORECAST - The upper symbol depicts
Surface Analysis. The lower symbol depicts City Forecast. The age of the
displayed data for each is shown at the right. The selected forecast period is
shown at the bottom.
Hazard
Avoidance
METAR - Available for the US and Canada. The age of the displayed data for
each is shown at the right.
Procedures
SIGMET & AIRMET - The age of the displayed data for each is shown at the
right.
Abnormal
Operation
FREEZING LEVEL - The age of the displayed data is shown at the right.
Appendix
COUNTY WARNING - The age of the displayed data is shown at the right.
Annun/Alerts
WINDS ALOFT - Available for the US and Canada. The age of the displayed
data for each is shown at the right. The altitude selection is shown at the
bottom.
CYCLONE WARNING - The age of the displayed data is shown at the right.
Index
AIREP - The age of the displayed data is shown at the right.
190-01462-00 Rev. A
Garmin G1000 Cockpit Reference Guide for the Piper PA-44-180 Seminole
47
Flight
Instruments
Hazard Avoidance
Wx Product
Status Icons
EIS
PIREP - The age of the displayed data is shown at the right. Urgent Pireps
are displayed in yellow.
Nav/Com/
XPDR/Audio
TURBULENCE - The age of the displayed data is shown at the right. The
altitude selection is shown at the bottom.
GPS Nav
ICING POTENTIAL - The age of the displayed data is shown at the right.
The altitude selection is shown at the bottom.
No Status Icon
TFR- Depicted as an area outlined in yellow
TRAFFIC SYSTEMS
WARNING: Do not rely solely upon the display of traffic information for
collision avoidance maneuvering. The traffic display does not provide collision
avoidance resolution advisories and does not under any circumstances or
conditions relieve the pilot’s responsibility to see and avoid other aircraft.
Hazard
Avoidance
Procedures
Flight
Planning
Description
Abnormal
Operation
Additional
Features
WARNING: Do not rely solely upon the display of traffic information to
accurately depict all of the traffic within range of the aircraft. Due to lack
of equipment, poor signal reception, and/or inaccurate information from
aircraft or ground stations, traffic may be present that is not represented on
the display.
Appendix
Annun/Alerts
• If Traffic information Service (TIS) is configured, a STANDBY, OPERATE, and
TNA MUTE Softkey are displayed.
• If a Traffic Advisory System (TAS) is configured, a STANDBY, NORMAL, TEST,
and ALT MODE Softkey are displayed.
• If an ADS-B traffic system is configured, only the ALT MODE Softkey is displayed.
Traffic Symbol
Description
Index
Non-Threat Traffic
(intruder is beyond 5 nm and greater than 1200’ vertical separation)
Proximity Advisory (PA) (Not available with TIS system)
(intruder is within 5 nm and less than 1200’ vertical separation)
48
Garmin G1000 Cockpit Reference Guide for the Piper PA-44-180 Seminole
190-01462-00 Rev. A
Hazard Avoidance
Flight
Instruments
Traffic Symbol
Description
Traffic Advisory (TA)
(closing rate, distance, and vertical separation meet TA criteria)
EIS
Traffic Advisory Off Scale
Nav/Com/
XPDR/Audio
Traffic Symbol Description
GPS Nav
Traffic Information Service (TIS)
Displaying Traffic on the Traffic Map Page
3)
Press the OPERATE Softkey to begin displaying traffic. ‘OPERATING’ is
displayed in the Traffic Mode field.
4)
Press the STANDBY Softkey to place the system in the Standby Mode.
‘STANDBY’ is displayed in the Traffic Mode field.
5)
Rotate the Joystick clockwise to display a larger area or rotate counterclockwise to display a smaller area.
6)
Press the TNA MUTE Softkey to mute the “Traffic Not Available” aural
alert, (if desired)
Annun/Alerts
Turn the small FMS Knob to select the Traffic Map Page.
Abnormal
Operation
2)
Additional
Features
Turn the large FMS Knob to select the Map Page Group.
Hazard
Avoidance
1)
Displaying Traffic on the Navigation Map
2)
Press the TRAFFIC Softkey. Traffic is now displayed on the map.
190-01462-00 Rev. A
Garmin G1000 Cockpit Reference Guide for the Piper PA-44-180 Seminole
Index
Ensure TIS is operating. With the Navigation Map displayed, press the
MAP Softkey.
Appendix
1)
Procedures
NOTE: Traffic Information Service (TIS) is only available when the aircraft is
within the service volume of a TIS capable terminal radar site.
Flight
Planning
NOTE: If the G1000 is configured to use an optional Traffic Advisory System
(TAS), TIS is not available for use.
49
Hazard Avoidance
Flight
Instruments
GTS 800 (Optional)
Nav/Com/
XPDR/Audio
EIS
WARNING: The Traffic Advisory System (TAS) is intended for advisory use
only to aid the pilot in visually acquiring traffic. No avoidance maneuvers
should be based solely upon TAS traffic information. It is the responsibility
of the pilot in command to see and maneuver to avoid traffic.
Flight
Planning
GPS Nav
NOTE: Pilots should be aware of TAS system limitations. TAS systems
require transponders of other aircraft to respond to system interrogations.
If the transponders do not respond to interrogations due to phenomena
such as antenna shading or marginal transponder performance, traffic may
be displayed intermittently, or not at all. Aircraft without altitude reporting
capability are shown without altitude separation data or climb descent
indication. Pilots should remain vigilant for traffic at all times.
1)
Set the range to 2/6 nm.
2)
Press the STANDBY Softkey.
3)
Press the TEST Softkey.
4)
Self test takes approximately eight seconds to complete. When completed
successfully, traffic symbols display and a voice alert “Traffic Advisory
System Test Passed” is heard. If the self test fails, the system reverts to
Standby Mode and a voice alert “Traffic Advisory System Test Failed” is
heard.
Abnormal
Operation
Additional
Features
Hazard
Avoidance
Procedures
System Self Test
Enabling/Disabling Flight ID Display
Annun/Alerts
On the Traffic Map Page, press the FLT ID Softkey.
1)
Turn the large FMS Knob to select the Map Page Group.
Appendix
2)
Turn the small FMS Knob to select the Traffic Map Page.
3)
Press the OPERATE Softkey to begin displaying traffic. OPERATING is
displayed in the Traffic mode field.
Index
Displaying Traffic on the Traffic Map Page
4)
Press the ALT MODE Softkey to change the altitude volume.
5)
Press the STANDBY Softkey to place the system in the Standby mode.
STANDBY is displayed in the Traffic mode field.
50
Garmin G1000 Cockpit Reference Guide for the Piper PA-44-180 Seminole
190-01462-00 Rev. A
Hazard Avoidance
Turn the RANGE Knob clockwise to display a larger area or counterclockwise to display a smaller area.
Flight
Instruments
6)
Displaying Traffic on the Navigation Map
EIS
Ensure TAS is operating.
2)
With the Navigation Map displayed, press the MAP Softkey.
3)
Press the TRAFFIC Softkey. Traffic is now displayed on the map.
Nav/Com/
XPDR/Audio
1)
Aircraft Identification
(tail number or Flight
ID number)
Flight
Planning
Relative Altitude (in this
case 1200 feet above own
aircraft)
Procedures
Altitude Trend (up arrow
indicates climbing, down
arrow indicates descending)
Intruder Aircraft
Ground Track (extends
in the direction of the
aircraft movement)
Hazard
Avoidance
Example ADS-B Traffic Advisory (GTS 800 only)
Description
Additional
Features
Symbol
Traffic Advisory with ADS-B directional information. Points in the direction of the intruder
aircraft track. (GTS 800 only)
Abnormal
Operation
Traffic Advisory without directional information.
Annun/Alerts
Traffic Advisory out of the selected display range. Displayed at outer range ring at proper
bearing.
Appendix
Non-threat traffic with ADS-B directional information. Points in the direction of the aircraft
track. (GTS 800 only)
Non-threat traffic with ADS-B directional information. Points in the direction of the intruder
aircraft track. (GTS 800 only)
Index
Non-threat traffic with no directional information.
Traffic with ADS-B directional information, but positional accuracy is degraded. Points in the
direction of the aircraft track. (GTS 800 only)
190-01462-00 Rev. A
Garmin G1000 Cockpit Reference Guide for the Piper PA-44-180 Seminole
GPS Nav
NOTE: A 1090 MHz extended squitter transponder is required to display
ADS-B symbology for aircraft providing ADS-B data.
51
TERRAIN AND OBSTACLE PROXIMITY
NOTE: Terrain data is not displayed when the aircraft is outside the installed
terrain database coverage area.
EIS
Flight
Instruments
Hazard Avoidance
1)
Turn the large FMS Knob to select the Map Page Group.
2)
Turn the small FMS Knob to select the Terrain Proximity Page.
3)
If desired, press the VIEW Softkey to access the ARC and 360 Softkeys.
When the ARC Softkey is pressed, a radar-like 120° view is displayed. Press
the 360 Softkey to return to the 360° default display.
4)
Rotate the Joystick clockwise to display a larger area or rotate counterclockwise to display a smaller area.
Additional
Features
Hazard
Avoidance
Procedures
Flight
Planning
GPS Nav
Nav/Com/
XPDR/Audio
Displaying Terrain and Obstacles on the Terrain Proximity Page
Color
Terrain/Obstacle Location
Red
Terrain/Obstacle above or within 100’
below current aircraft altitude.
Yellow
Terrain/Obstacle between 100’ and
1000’ below current aircraft altitude.
Black
Terrain/Obstacle is more than 1000’
below aircraft altitude.
1)
With the Navigation Map displayed, press the MAP Softkey.
2)
Press the TERRAIN Softkey. Terrain and obstacle proximity will now be
displayed on the map.
3)
Terrain and obstacles may be displayed in the Profile View by selecting the
PROFILE Softkey.
Index
Appendix
Annun/Alerts
Abnormal
Operation
Displaying Terrain and Obstacles on the Navigation Map
52
Garmin G1000 Cockpit Reference Guide for the Piper PA-44-180 Seminole
190-01462-00 Rev. A
Hazard Avoidance
NOTE: Terrain-SVS is only available when the Synthetic Vision Technology
(SVT) option is installed and the TAWS-B option has not been installed.
Flight
Instruments
TERRAIN-SVS
EIS
Display Terrain on the TERRAIN-SVS Page
Turn the small FMS Knob to select the Terrain-SVS Page.
3)
If desired, press the VIEW Softkey to access the ARC and 360 softkeys.
When the ARC Softkey is pressed, a radar-like 120° view is displayed.
Press the 360 Softkey to return to the 360° default display.
4)
Rotate the Joystick clockwise to display a larger area or rotate counterclockwise to display a smaller area.
Terrain/Obstacle above or within 100’
below current aircraft altitude.
Yellow
Terrain/Obstacle between 100’ and
1000’ below current aircraft altitude.
Black
Terrain/Obstacle is more than 1000’
below aircraft altitude.
Abnormal
Operation
Red
Additional
Features
Terrain/Obstacle Location
Hazard
Avoidance
Color
Procedures
2)
Flight
Planning
Turn the large FMS Knob to select the Map Page Group.
GPS Nav
1)
Enable/Disable Aviation Data
While the Terrain-SVS Page is displayed, press the MENU Key.
2)
Turn the small FMS Knob to select “Show (or Hide) Aviation Data”.
3)
Press the ENT Key.
Annun/Alerts
1)
Nav/Com/
XPDR/Audio
NOTE: Terrain data is not displayed when the aircraft is outside the installed
terrain database coverage area.
Appendix
Index
190-01462-00 Rev. A
Garmin G1000 Cockpit Reference Guide for the Piper PA-44-180 Seminole
53
Hazard Avoidance
Flight
Instruments
Terrain-SVS Inhibit
Nav/Com/
XPDR/Audio
EIS
Inhibit Terrain
While the Terrain-SVS Page is displayed, press the INHIBIT Softkey.
Or:
1) Press the MENU Key.
2) Turn the small FMS Knob to select ‘Inhibit Terrain’.
3) Press the ENT Key.
Procedures
Flight
Planning
GPS Nav
Enable Terrain
While the Terrain-SVS Page is displayed, press the INHIBIT Softkey.
Or:
1) While the Terrain-SVS Page is displayed, press the MENU Key.
2) Turn the small FMS Knob to select ‘Enable Terrain’.
3) Press the ENT Key.
Index
Appendix
Annun/Alerts
Abnormal
Operation
Additional
Features
Hazard
Avoidance
NOTE: If Terrain-SVS alerts are inhibited when the Final Approach Fix is the
active waypoint in a GPS SBAS approach, a LOW ALT annunciation may appear
on the PFD next to the altimeter if the current aircraft altitude is at least 164
feet below the prescribed altitude at the Final Approach Fix.
54
Garmin G1000 Cockpit Reference Guide for the Piper PA-44-180 Seminole
190-01462-00 Rev. A
Hazard Avoidance
Flight
Planning
Manual System Test
While the TAWS-B Page is displayed, press the MENU Key.
2)
Turn the small FMS Knob to select ‘Test TAWS’.
3)
Press the ENT Key. During the test ‘TAWS TEST’ is displayed in the center
of the TAWS-B Page.
Procedures
1)
Hazard
Avoidance
When all is in working order, “TAWS System Test, OK” is heard.
Display Terrain on the TAWS-B Page
Turn the small FMS Knob to select the TAWS-B Page.
3)
If desired, press the VIEW Softkey to access the ARC and 360 softkeys.
When the ARC Softkey is pressed, a radar-like 120° view is displayed.
Press the 360 Softkey to return to the 360° default display.
4)
Rotate the Joystick clockwise to display a larger area or rotate counterclockwise to display a smaller area.
Red
Terrain/Obstacle above or within 100’
below current aircraft altitude.
Yellow
Terrain/Obstacle between 100’ and
1000’ below current aircraft altitude.
Black
Terrain/Obstacle is more than 1000’
below aircraft altitude.
Garmin G1000 Cockpit Reference Guide for the Piper PA-44-180 Seminole
Index
Terrain/Obstacle Location
Appendix
190-01462-00 Rev. A
Color
Annun/Alerts
2)
Abnormal
Operation
Turn the large FMS Knob to select the Map Page Group.
Additional
Features
1)
GPS Nav
NOTE: TAWS-B operation is only available when the G1000 is configured for
a TAWS-B installation.
Nav/Com/
XPDR/Audio
NOTE: Terrain data is not displayed when the aircraft is outside the installed
terrain database coverage area.
EIS
WARNING: Do not use the terrain avoidance feature as the sole means of
navigation and terrain separation. The terrain avoidance feature is only to
be used as and aid to terrain avoidance. Garmin obtains terrain database
content from third party sources and is not able to independently verify the
accuracy of the terrain data.
Flight
Instruments
TERRAIN AWARENESS & WARNING SYSTEM (TAWS-B) DISPLAY (OPTIONAL)
55
Hazard Avoidance
EIS
Flight
Instruments
Enable/Disable Aviation Data
1)
While the TAWS-B Page is displayed, press the MENU Key.
2)
Turn the small FMS Knob to select “Show (or Hide) Aviation Data”.
3)
Press the ENT Key.
Nav/Com/
XPDR/Audio
TAWS Inhibit
GPS Nav
NOTE: If TAWS-B alerts are inhibited when the Final Approach Fix is the active
waypoint in a GPS SBAS approach, a LOW ALT annunciation may appear on
the PFD next to the altimeter if the current aircraft altitude is at least 164
feet below the prescribed altitude at the Final Approach Fix.
Hazard
Avoidance
Procedures
Flight
Planning
Inhibit TAWS
While the TAWS-B Page is displayed, press the INHIBIT Softkey.
Or:
1) Press the MENU Key.
2) Turn the small FMS Knob to select ‘Inhibit TAWS’.
3) Press the ENT Key.
Index
Appendix
Annun/Alerts
Abnormal
Operation
Additional
Features
Enable TAWS
While the TAWS-B Page is displayed, press the INHIBIT Softkey.
Or:
1) While the TAWS-B Page is displayed, press the MENU Key.
2) Turn the small FMS Knob to select ‘Enable TAWS’.
3) Press the ENT Key.
56
Garmin G1000 Cockpit Reference Guide for the Piper PA-44-180 Seminole
190-01462-00 Rev. A
Additional Features
Flight
Instruments
ADDITIONAL FEATURES
SYNTHETIC VISION (OPTIONAL)
Abnormal
Operation
Annun/Alerts
3)
Press the SYN TERR Softkey.
4)
Press the BACK Softkey to return to the previous page.
190-01462-00 Rev. A
Garmin G1000 Cockpit Reference Guide for the Piper PA-44-180 Seminole
Index
Press the SYN VIS Softkey.
Appendix
2)
Additional
Features
Press the PFD Softkey.
Hazard
Avoidance
Displaying SVT Terrain
1)
Procedures
Pathways
Flight Path Marker
Horizon Heading Marks
Terrain and Obstacle Alerting
Three-dimensional Traffic
Airport Signs
Runway Display
Flight
Planning
•
•
•
•
•
•
•
GPS Nav
Synthetic Vision Technology (SVT) functionality is offered as an optional
enhancement to the G1000 Integrated Flight Deck System.
SVT is primarily comprised of a computer-generated forward-looking, attitude
aligned view of the topography immediately in front of the aircraft from the pilot’s
perspective. SVT information is shown on the primary flight display (PFD).
SVT offers a three-dimensional view of terrain and obstacles. Terrain and
obstacles that pose a threat to the aircraft in flight are shaded yellow or red.
In addition to SVT enhancement to the PFD, the following feature enhancements
have been added to the PFD:
Nav/Com/
XPDR/Audio
WARNING: Do not use SVT runway depiction as the sole means for
determining the proximity of the aircraft to the runway or for maintaining
the proper approach path angle during landing.
EIS
WARNING: Use appropriate primary systems for navigation, and for terrain,
obstacle, and traffic avoidance. SVT is intended as an aid to situational
awareness only and may not provide either the accuracy or reliability upon
which to solely base decisions and/or plan maneuvers to avoid terrain,
obstacles, or traffic.
57
Additional Features
Nav/Com/
XPDR/Audio
EIS
Flight
Instruments
Displaying Pathways
2)
Press the SYN VIS Softkey.
3)
If not already enabled, press the SYN TERR Softkey.
4)
Press the PATHWAY Softkey.
5)
Press the BACK Softkey to return to the previous page.
GPS Nav
Flight
Planning
Procedures
1)
Press the PFD Softkey.
2)
Press the SYN VIS Softkey.
3)
If not already enabled, press the SYN TERR Softkey.
4)
Press the HRZN HDG Softkey.
5)
Press the BACK Softkey to return to the previous page.
Displaying Airport Signs
Hazard
Avoidance
Additional
Features
Press the PFD Softkey.
Displaying Heading on the Horizon
1)
Press the PFD Softkey.
2)
Press the SYN VIS Softkey.
3)
If not already enabled, press the SYN TERR Softkey.
4)
Press the APTSIGNS Softkey.
5)
Press the BACK Softkey to return to the previous page.
TERMINAL PROCEDURE CHARTS
Abnormal
Operation
Annun/Alerts
Appendix
Index
1)
NOTE: With the availability of SafeTaxi®, ChartView, or FliteCharts®, it may
be necessary to carry another source of charts on-board the aircraft.
SafeTaxi®
SafeTaxi® is an enhanced feature that gives greater map detail as the map range
is adjusted in on the airport. The airport display on the map reveals runways with
numbers, taxiways identifiers, and airport landmarks including ramps, buildings,
control towers, and other prominent features. Resolution is greater at lower map
ranges. The aircraft symbol provides situational awareness while taxiing.
Pressing the DCLTR Softkey (declutter) once removes the taxiway markings and
airport identification labels. Pressing the DCLTR Softkey twice removes VOR station
ID, the VOR symbol, and intersection names if within the airport plan view. Pressing
58
Garmin G1000 Cockpit Reference Guide for the Piper PA-44-180 Seminole
190-01462-00 Rev. A
Additional Features
3)
Press the GO BACK Softkey to return to the previous page.
190-01462-00 Rev. A
Garmin G1000 Cockpit Reference Guide for the Piper PA-44-180 Seminole
Index
Press the DP, STAR, APR, WX, and NOTAM softkeys to access charts for
departures, arrivals, approaches, weather and NOTAMs Note that NOTAMS
are only available with ChartView.
Appendix
2)
Annun/Alerts
Move the map pointer to point to a desired point on the map and press the
SHW CHRT Softkey.
Abnormal
Operation
Or:
Additional
Features
Press the SHW CHRT Softkey when displayed.
Hazard
Avoidance
1)
Procedures
View Charts from the Navigation Map Page
Flight
Planning
FliteCharts® resemble the paper version of AeroNav Services terminal procedures
charts. The charts are displayed with high-resolution and in color for applicable
charts. The MFD depiction shows the aircraft position on the plan view of most
approach charts.
The FliteCharts database contains procedure charts for the United States only.
This database is updated on a 28-day cycle. If not updated within 180 days of the
expiration date, FliteCharts will no longer function.
GPS Nav
FliteCharts®
Nav/Com/
XPDR/Audio
ChartView resembles the paper version of Jeppesen terminal procedures charts.
The charts are displayed in full color with high-resolution. The MFD depiction shows
the aircraft position on the moving map in the plan view of most approach charts and
on airport diagrams.
The ChartView database is updated on a 14-day cycle. If the ChartView database is
not updated within 70 days of the expiration date, ChartView will no longer function.
EIS
ChartView (Optional)
Flight
Instruments
the DCLTR Softkey a third time removes the airport runway layout, unless the airport
in view is part of an active route structure. Pressing the DCLTR Softkey again cycles
back to the original map detail.
The SafeTaxi database contains detailed airport diagrams for selected airports.
These diagrams provide the pilot with situational awareness by displaying the aircraft
position in relation to taxiways, ramps, runways, terminals, and services. This
information should not be used by the pilot as the basis for maneuvering the aircraft
on the ground. This database is updated on a 56-day cycle.
59
Additional Features
While viewing the Active Flight Plan Page, press the FMS Knob to activate
the cursor.
EIS
2)
Turn the large FMS Knob to select the departure airport, destination
airport, departure, arrival, or approach.
3)
Press the SHW CHRT Softkey. The appropriate chart is displayed, if
available for the item selected.
4)
Press the GO BACK Softkey to return to the previous page.
GPS Nav
1)
Nav/Com/
XPDR/Audio
Flight
Instruments
View Charts from the Active Flight Plan Page
While viewing a chart press the MENU Key to display the Page Menu
OPTIONS.
2)
Turn the large FMS Knob to highlight the ‘Chart Setup’ Menu Option and
press the ENT Key.
3)
Turn the large FMS Knob to move between the ‘FULL SCREEN’ and ‘COLOR
SCHEME’ Options.
4)
Turn the small FMS Knob to choose between the ‘On’ and ‘Off’ Full Screen
Options.
5)
Turn the small FMS Knob to choose between ‘Day’, ‘Auto’, and ‘Night’
Options.
Additional
Features
6)
In Auto Mode, turn the large FMS Knob to select the percentage field and
change percentage with the small FMS Knob. The percentage of change is
the day/night crossover point based on backlighting intensity.
7)
Press the FMS Knob when finished to remove the Chart Setup Menu.
Index
Appendix
Annun/Alerts
Hazard
Avoidance
Procedures
Flight
Planning
1)
Abnormal
Operation
Change Day/Night View
AIRPORT DIRECTORY
The Aircraft Owners and Pilots Association (AOPA) or AC-U-KWIK Airport
Directory database offers detailed information regarding services, hours of operation,
lodging options, and more for various airports. This information is viewed on the
WPT-Airport Information Page.
The Airport Directory databases are revised every 56 days. The Airport Directory is
always available for use after the expiration date. Check fly.garmin.com for the current
database.
60
Garmin G1000 Cockpit Reference Guide for the Piper PA-44-180 Seminole
190-01462-00 Rev. A
Additional Features
Flight
Instruments
View Airport Directory Information
EIS
While viewing the WPT-Airport Information Page, if necessary, press the
INFO-1 Softkey to change the softkey label to display INFO-2. Airport
information is displayed on the right half of the display.
The XM Radio Page provides information and control of the audio entertainment
features of the SiriusXM Satellite Radio.
Turn the large FMS Knob to select the Auxiliary Page Group.
2)
Turn the small FMS Knob to select XM Radio.
3)
Press the RADIO Softkey to show the XM Radio Page where audio
entertainment is controlled.
Flight
Planning
1)
GPS Nav
Selecting the XM Radio Page
2)
Press the CH + Softkey to go down through the list in the Channel Box, or
move up the list with the CH – Softkey.
Garmin G1000 Cockpit Reference Guide for the Piper PA-44-180 Seminole
61
Index
While on the XM Radio Page, press the CHNL Softkey.
Appendix
1)
Annun/Alerts
Select an Available Channel within the Selected Category
Abnormal
Operation
The Category Box of the XM Radio Page displays the currently selected category
of audio.
1) Press the CATGRY Softkey on the XM Radio Page.
2) Press the CAT + and CAT - softkeys to cycle through the categories.
Or:
Turn the small FMS Knob to display the ‘Categories’ list. Highlight the
desired category with the small FMS Knob.
3) Press the ENT Key.
Additional
Features
Selecting a Category
Hazard
Avoidance
The Active Channel Box on the XM Radio Page displays the currently selected
channel. The Channels List Box of the XM Radio Page shows a list of the available
channels for the selected category.
Procedures
Active Channel and Channel List
190-01462-00 Rev. A
Nav/Com/
XPDR/Audio
SIRIUSXM RADIO ENTERTAINMENT
Additional Features
Flight
Instruments
Or:
Press the FMS Knob to highlight the channel list and turn the large FMS
Knob to scroll through the channels.
EIS
3)
With the desired channel highlighted, press the ENT Key.
Nav/Com/
XPDR/Audio
While on the XM Radio Page, press the CHNL Softkey.
2)
Press the DIR CH Softkey. The channel number in the Active Channel Box
is highlighted.
3)
Press the numbered softkeys located on the bottom of the display to
directly select the desired channel number.
4)
Press the ENT Key to activate the selected channel.
Flight
Planning
1)
GPS Nav
Entering a Channel Directly
Assigning Channel Presets
Abnormal
Operation
Additional
Features
Hazard
Avoidance
Procedures
Up to 15 channels from any category can be assigned a preset number.
1) On the XM Radio Page, with the desired channel active, press the PRESETS
Softkey to access the first five preset channels (PS1 - PS5).
2) Press the MORE Softkey to access the next five channels (PS6 – PS10),
and again to access the last five channels (PS11 – PS15). Pressing the
MORE Softkey repeatedly cycles through the preset channels.
3) Press the SET Softkey.
4) Press any one of the (PS1 - PS15) softkeys to assign a number to the
active channel.
Appendix
Annun/Alerts
Adjusting Volume
1)
With the XM Radio Page displayed, press the VOL Softkey.
2)
Press the VOL – Softkey to reduce volume or press the VOL + Softkey to
increase volume. (Once the VOL Softkey is pressed, the volume can also be
adjusted using the small FMS Knob.)
Index
Mute SiriusXM Audio
62
1)
Select the XM Radio Page or XM Information Page.
2)
Press the MUTE Softkey to mute the audio. Press the MUTE Softkey again
to unmute the audio.
Garmin G1000 Cockpit Reference Guide for the Piper PA-44-180 Seminole
190-01462-00 Rev. A
Additional Features
Turn the large FMS Knob to highlight the first empty scheduler message
naming field.
4)
Use the FMS Knob to enter the message text to be displayed in the
Messages Window and press the ENT Key.
5)
Press the ENT Key again or use the large FMS Knob to move the cursor to
the field next to Type.
6)
Turn the small FMS Knob to select the message type:
Hazard
Avoidance
• Event—Message issued at the specified date/time
• One-time—Message issued when the message timer reaches zero
(default setting)
8)
For periodic and one-time message, use the FMS Knob to enter the timer
value (HH:MM:SS) from which to countdown and press the ENT Key.
9)
For event-based messages:
Annun/Alerts
Press the ENT Key again or use the large FMS Knob to move the cursor to
the next field.
a) Use the FMS Knob to enter the desired date (DD-MM-YY) and press
the ENT Key.
10) Press the ENT Key again or use the large FMS Knob to move the cursor to
enter the next message.
63
Index
c) Use the FMS Knob to enter the desired time (HH:MM) and press the
ENT Key.
Appendix
b) Press the ENT Key again or use the large FMS Knob to move the cursor
to the next field.
Garmin G1000 Cockpit Reference Guide for the Piper PA-44-180 Seminole
Abnormal
Operation
7)
Additional
Features
• Periodic—Message issued each time the message timer reaches zero
190-01462-00 Rev. A
Procedures
3)
Flight
Planning
Press the FMS Knob momentarily to activate the flashing cursor.
GPS Nav
2)
Nav/Com/
XPDR/Audio
Entering a Scheduler Message
1) Select the AUX - Utility Page.
EIS
The Scheduler feature can be used to enter and display reminder messages (e.g., Change
oil, Altimeter-Transponder, or Hot Section Inspection or Phase 1 Maintenance Check) in
the Messages Window on the PFD. Message timers set to periodic alerting automatically
reset to the original timer value once the message is displayed. When power is cycled, all
messages are retained until deleted, and message timer countdown is resumed.
Flight
Instruments
SCHEDULER
Additional Features
Flight
Instruments
Deleting a Scheduler Message
2)
Press the FMS Knob momentarily to activate the flashing cursor.
3)
Turn the large FMS Knob to highlight the name field of the scheduler
message to be deleted.
4)
Press the CLR Key to clear the message text. If the CLR Key is pressed
again, the message is restored.
5)
Press the ENT Key while the message line is cleared to clear the message
time.
When a scheduler message is waiting, the MSG Softkey flashes. Pressing the
MSG Softkey opens the Messages Window and acknowledges the scheduler message.
Pressing the MSG Softkey again removes the Messages Window from the display, and
the scheduler message is deleted from the message queue.
PILOT PROFILES
Creating a profile:
Hazard
Avoidance
Procedures
Flight
Planning
GPS Nav
Nav/Com/
XPDR/Audio
EIS
1) Select the AUX - Utility Page.
1) Use the FMS Knob to select the AUX - System Setup Page.
Additional
Features
2)
Press the FMS Knob momentarily to activate the flashing cursor.
3) Turn the large FMS Knob to highlight ‘CREATE’ in the Pilot Profile Box.
4)
Press the ENT Key. A ‘Create Profile’ window is displayed.
Abnormal
Operation
5) Use the FMS Knob to enter a profile name up to 16 characters long and
6)
In the next field, use the small FMS Knob to select the desired settings
upon which to base the new profile. Profiles can be created based on
Garmin factory defaults, default profile settings (initially based on Garmin
factory defaults unless edited by the pilot), or current system settings.
7)
Press the ENT Key.
Index
Appendix
Annun/Alerts
press the ENT Key. Pilot profile names cannot begin with a blank as the
first letter.
64
Garmin G1000 Cockpit Reference Guide for the Piper PA-44-180 Seminole
190-01462-00 Rev. A
Additional Features
Flight
Instruments
8) With ‘CREATE’ highlighted, press the ENT Key to create the profile
Or:
9)
EIS
Use the large FMS Knob to select ‘CREATE and ACTIVATE’ and press the
ENT Key to activate the new profile.
Selecting an active profile:
2)
GPS Nav
1) Use the FMS Knob to select the AUX - System Setup Page.
Nav/Com/
XPDR/Audio
To cancel the process, select ‘CANCEL’ with the large FMS Knob and press
the ENT Key.
Press the FMS Knob momentarily to activate the flashing cursor.
3) Turn the large FMS Knob to highlight the active profile field in the Pilot
Flight
Planning
Profile Box.
4) Turn the small FMS Knob to display the pilot profile list and highlight the
Procedures
desired profile.
5) Press the ENT Key. The system loads and displays the system settings for
the selected profile.
Hazard
Avoidance
Renaming a profile:
1) Use the FMS Knob to select the AUX - System Setup Page.
Press the FMS Knob momentarily to activate the flashing cursor.
Additional
Features
2)
3) Turn the large FMS Knob to highlight ‘RENAME’ in the Pilot Profile Box.
Press the ENT Key.
5) In the ‘Rename Profile’ window, turn the FMS Knob to select the profile to
rename.
Press the ENT Key.
Annun/Alerts
6)
7) Use the FMS Knob to enter a new profile name up to 16 characters long
and press the ENT Key.
Appendix
8) With ‘RENAME’ highlighted, press the ENT Key.
9)
Abnormal
Operation
4)
To cancel the process, use the large FMS Knob to select ‘CANCEL’ and
press the ENT Key.
Index
190-01462-00 Rev. A
Garmin G1000 Cockpit Reference Guide for the Piper PA-44-180 Seminole
65
Additional Features
Flight
Instruments
Deleting a profile:
1) Use the FMS Knob to select the AUX - System Setup Page.
EIS
2)
Press the FMS Knob momentarily to activate the flashing cursor.
3) Turn the large FMS Knob to highlight ‘DELETE’ in the Pilot Profile Box.
Nav/Com/
XPDR/Audio
4)
Press the ENT Key.
5) In the ‘Delete Profile’ window, turn the FMS Knob to select the profile to
delete.
GPS Nav
6)
Press the ENT Key.
7) With ‘DELETE’ highlighted, press the ENT Key.
Flight
Planning
8)
To cancel the process, use the large FMS Knob to select ‘CANCEL’ and
press the ENT Key.
Procedures
Importing a profile:
1)
Insert the SD card containing the Pilot Profile into the top card slot on the
MFD.
Hazard
Avoidance
2) Use the FMS Knob to select the AUX - System Setup Page.
Additional
Features
3)
Press the IMPORT softkey. If the correct Pilot Profile file is selected; with
‘IMPORT’ highlighted press the ENT Key.
Or:
If the SD card contains more than one Pilot Profile:
Abnormal
Operation
a) Turn the large FMS Knob to highlight the select file field in the Pilot
Profile Importing Box.
Annun/Alerts
b) Turn the small FMS Knob to display the pilot profile list and highlight
the desired profile to import and press the ENT Key.
c) With ‘IMPORT’ highlighted, press the ENT Key.
“Pilot profile import succeeded.” is shown in the import results box. Press
the ENT Key. The imported profile becomes the active Pilot Profile.
Index
Appendix
4)
66
Garmin G1000 Cockpit Reference Guide for the Piper PA-44-180 Seminole
190-01462-00 Rev. A
Additional Features
1)
2) Use the FMS Knob to select the AUX - System Setup Page.
4)
Press the EXPORT softkey.
5)
With ‘EXPORT’ highlighted press the ENT Key.
6)
“Pilot profile export succeeded.” is shown in the export results box. Press
the ENT Key to exit the Pilot Profile Exporting Box.
GPS Nav
Activate the desired Pilot Profile to export. Only the active Pilot Profile can
be exported.
Nav/Com/
XPDR/Audio
3)
EIS
Insert the SD card for storing the Pilot Profile into the top card slot on the
MFD.
Flight
Instruments
Exporting a profile:
Flight
Planning
Procedures
Hazard
Avoidance
Additional
Features
Abnormal
Operation
Annun/Alerts
Appendix
Index
190-01462-00 Rev. A
Garmin G1000 Cockpit Reference Guide for the Piper PA-44-180 Seminole
67
Index
Appendix
Annun/Alerts
Abnormal
Operation
Additional
Features
Hazard
Avoidance
Procedures
Flight
Planning
GPS Nav
Nav/Com/
XPDR/Audio
EIS
Flight
Instruments
Additional Features
Blank Page
68
Garmin G1000 Cockpit Reference Guide for the Piper PA-44-180 Seminole
190-01462-00 Rev. A
Abnormal Operation
Flight
Instruments
ABNORMAL OPERATION
REVERSIONARY MODE
GPS Nav
• MFD failure – PFD automatically enters reversionary mode.
Flight
Planning
• Reversionary display mode can be manually activated by pressing the
DISPLAY BACKUP Button on the audio panel. When the DISPLAY
BACKUP Button is selected both displays enter reversionay display mode.
Hazard
Avoidance
ABNORMAL COM OPERATION
Annun/Alerts
If GPS position is lost, or becomes invalid, selected hazards being displayed on the
Navigation Map Page are removed until GPS position is again established.
Abnormal
Operation
HAZARD DISPLAYS WITH LOSS OF GPS POSITION
Additional
Features
When a COM tuning failure is detected by the system, the emergency frequency
(121.500 MHz) is automatically loaded into the active frequency field of the COM
radio for which the tuning failure was detected. In the event of a failure of both PFD
and MFD, the emergency frequency (121.500 MHz) automatically becomes the active
frequency on both COM radios.
Appendix
Index
Loss of Hazard Functions with Loss of GPS
Position
Garmin G1000 Cockpit Reference Guide for the Piper PA-44-180 Seminole
Procedures
NOTE: The PA-44-180 Seminole Pilot’s Operating Handbook (POH) always
takes precedence over the information found in this section.
190-01462-00 Rev. A
Nav/Com/
XPDR/Audio
• PFD failure – MFD does not automatically enter reversionary mode,
reversionary mode must be activated manually.
EIS
In reversionary mode, critical flight instrumentation is combined with engine
instrumentation on the remaining displays.
When a system detected failure occurs, the display reversionary modes are as
follows:
69
UNUSUAL ATTITUDES
The PFD ‘declutters’ when the aircraft enters an unusual attitude. Only the primary
functions are displayed in these situations.
The following information is removed from the PFD (and corresponding softkeys
are disabled) when the aircraft experiences unusual attitudes:
• Traffic Annunciations
• AFCS Annunciations
• Flight Director
Command Bars
• Inset Map
• Temperatures
• DME Information
Window
• Wind Data
• Selected Heading Box
• Selected Course Box
• Transponder Status
Box
• System Time
• PFD Setup Menu
• Windows displayed in
the lower right corner
of the PFD:
– Timer/References
– Nearest Airports
– Flight Plan
– Messages
– Procedures
• Barometric Minimum
Descent Altitude Box
• Glideslope, Glidepath,
and Vertical Deviation
Indicators
• Altimeter Barometric
Setting
• Selected Altitude
• VNV Target Altitude
Index
Appendix
Annun/Alerts
Abnormal
Operation
Additional
Features
Hazard
Avoidance
Procedures
Flight
Planning
GPS Nav
Nav/Com/
XPDR/Audio
EIS
Flight
Instruments
Abnormal Operation
Extreme Pitch Indication
DEAD RECKONING
While in Enroute or Oceanic phase of flight, if the G1000 detects an invalid GPS
solution or is unable to calculate a GPS position, the system automatically reverts to
Dead Reckoning (DR) Mode. In DR Mode, the G1000 uses its last-known position
combined with continuously updated airspeed and heading data (when available) to
calculate and display the aircraft’s current estimated position.
70
Garmin G1000 Cockpit Reference Guide for the Piper PA-44-180 Seminole
190-01462-00 Rev. A
Abnormal Operation
EIS
Nav/Com/
XPDR/Audio
GPS Nav
Flight
Planning
Procedures
Hazard
Avoidance
Additional
Features
Abnormal
Operation
Annun/Alerts
DR Mode is indicated on the G1000 by the appearance of the letters ‘DR’
superimposed in yellow over the ‘own aircraft’ symbol as shown in the following
figure. In addition, ‘DR’ is prominently displayed, also in yellow, on the HSI slightly
above and to the right of the aircraft symbol on the CDI as shown in the following
figure. The CDI deviation bar is displayed in yellow, but will be removed from the
display after 20 minutes. Lastly, but at the same time, a ‘GPS NAV LOST’ alert message
appears on the PFD.
Normal navigation using GPS/SBAS source data resumes automatically once a valid
GPS solution is restored.
It is important to note that estimated navigation data supplied by the G1000 in
DR Mode may become increasingly unreliable and must not be used as a sole means
of navigation. If, while in DR Mode, airspeed and/or heading data is also lost or
not available, the DR function may not be capable of estimating your position and,
consequently, the system may display a path that is different than the actual movement
of the aircraft. Estimated position information displayed by the G1000 through
DR while there is no heading and/or airspeed data available should not be used for
navigation.
DR Mode is inherently less accurate than the standard GPS/SBAS Mode due to the
lack of satellite measurements needed to determine a position. Changes in wind speed
and/or wind direction compounds the relative inaccuracy of DR Mode. Because of this
degraded accuracy, the crew must maintain position awareness using other navigation
equipment until GPS-derived position data is restored.
Flight
Instruments
NOTE: Dead Reckoning Mode only functions in Enroute (ENR) or Oceanic
(OCN) phase of flight. In all other phases, an invalid GPS solution produces
a “NO GPS POSITION” annunciation on the map and the G1000 stops
navigating in GPS Mode.
Appendix
Symbolic Aircraft
(Map pages and Inset Map)
Index
CDI ‘DR’ Indication on PFD
Dead Reckoning Indications
190-01462-00 Rev. A
Garmin G1000 Cockpit Reference Guide for the Piper PA-44-180 Seminole
71
As a result of operating in DR Mode, all GPS-derived data is computed based upon
an estimated position and is displayed as yellow text on the display to denote degraded
navigation source information. This data includes the following:
• Navigation Status Box fields except Active Leg, TAS, and DTK
• GPS Bearing Pointer
• Wind data and pointers in the Wind Data Box on the PFD
• Current Track Indicator
• All Bearing Pointer Distances
• Active Flight Plan distances, bearings, and ETE values
Also, while the G1000 is in DR Mode, the autopilot will couple to GPS for up
to 20 minutes. Terrain Proximity, TERRAIN-SVT, and TAWS-B are also disabled.
Additionally, the accuracy of all nearest information (airports, airspaces, and
waypoints) is questionable. Finally, airspace alerts continue to function, but with
degraded accuracy.
Index
Appendix
Annun/Alerts
Abnormal
Operation
Additional
Features
Hazard
Avoidance
Procedures
Flight
Planning
GPS Nav
Nav/Com/
XPDR/Audio
EIS
Flight
Instruments
Abnormal Operation
72
Garmin G1000 Cockpit Reference Guide for the Piper PA-44-180 Seminole
190-01462-00 Rev. A
Annunciations & Alerts
Flight
Instruments
ANNUNCIATIONS & ALERTS
G1000 SYSTEM ANNUNCIATIONS
GPS Nav
Comment
Nav/Com/
XPDR/Audio
System Annunciation
EIS
When an LRU or an LRU function fails, a large red “X” is typically displayed
on windows associated with the failed data. Refer to the PA-44-180 Archer Pilot’s
Operating Handbook (POH) for additional information regarding pilot responses to
these annunciations
Flight
Planning
Attitude and Heading Reference System is aligning.
Procedures
Hazard
Avoidance
Display system is not receiving attitude information from the
AHRS.
Additional
Features
Abnormal
Operation
GPS information is either not present or is invalid for
navigation use.
Note that AHRS utilizes GPS inputs during normal operation.
AHRS operation may be degraded if GPS signals are not
present (see POH).
Annun/Alerts
Display system is not receiving valid transponder information.
Appendix
Display system is not receiving valid heading input from
AHRS.
Index
190-01462-00 Rev. A
Garmin G1000 Cockpit Reference Guide for the Piper PA-44-180 Seminole
73
System Annunciation
Comment
Display system is not receiving airspeed input from air data
computer.
GPS Nav
Nav/Com/
XPDR/Audio
EIS
Flight
Instruments
Annunciations & Alerts
Procedures
Flight
Planning
Display system is not receiving altitude input from the air
data computer.
Additional
Features
Hazard
Avoidance
Display system is not receiving vertical speed input from the
air data computer.
A red ‘X’ through any other display field (such as engine
instrumentation display) indicates that the field is not
receiving valid data.
Index
Appendix
Annun/Alerts
Abnormal
Operation
Other Various Red X
Indications
74
Garmin G1000 Cockpit Reference Guide for the Piper PA-44-180 Seminole
190-01462-00 Rev. A
Annunciations & Alerts
EIS
The following annunciations are configured specifically for the PA-44-180
Seminole aircraft. See the PA-44-180 Seminole Pilot Operating Handbook (POH) for
information regarding pilot responses.
Flight
Instruments
CAS ANNUNCIATIONS
Warning Annunciations
Additional
Features
Abnormal
Operation
HTR OVERHEAT
Triple Chime
Hazard
Avoidance
CHECK GEAR
Procedures
GEAR SYS
Flight
Planning
R START ENGD
Left engine CHT in warning range
Right engine CHT in warning range
Left Alternator failure
Right Alternator failure
Left fuel quantity in warning range
Right fuel quantity in warning range
Left starter motor energized when engine is
running
Right starter motor energized when engine is
running
A failure of a gear system component has been
detected
Landing gear are not down and locked
or
Landing gear is selected UP on the ground
Heater unit has sensed an overheat condition
Audio Alert
GPS Nav
L START ENGD
Description
Nav/Com/
XPDR/Audio
Annunciation
Window Text
L ENG CHT
R ENG CHT
L ALTR FAIL
R ALTR FAIL
L FUEL QTY
R FUEL QTY
Annun/Alerts
Appendix
Index
190-01462-00 Rev. A
Garmin G1000 Cockpit Reference Guide for the Piper PA-44-180 Seminole
75
Caution Annunciations
Annunciation
Window Text
L FUEL QTY
R FUEL QTY
PITOT HEAT FAIL
PITOT HEAT OFF
GEAR SYS
GPS Nav
Nav/Com/
XPDR/Audio
EIS
Flight
Instruments
Annunciations & Alerts
CHECK GEAR
Audio Alert
Left fuel quantity in caution range
Right fuel quantity in caution range
Pitot heat failure
Pitot heat selected OFF
A failure of a gear system component has been
detected
Landing gear are not down and locked
Hydraulic pump is running when it should not be
running
Double Chime
Advisory Annunciations
Annunciation
Window Text
EMERG BATT ON
FUEL IMBAL
MAINT MODE ON
PFD FAN FAIL
MFD FAN FAIL
AV FAN FAIL
Description
Audio Alert
Emergency power in use
Fuel imbalance (left vs. right tank quantity)
Maintenance Mode ON
PFD display fan is inoperative
Single Chime
MFD display fan is inoperative
Avionics fan fail
SYSTEM MESSAGES
Alerts Window Text
WOW MISCOMPARE
Description
Left and right squat switches do not agree
Index
Appendix
Annun/Alerts
Abnormal
Operation
Additional
Features
Hazard
Avoidance
Procedures
Flight
Planning
HYDR PUMP ON
Description
76
Garmin G1000 Cockpit Reference Guide for the Piper PA-44-180 Seminole
190-01462-00 Rev. A
Annunciations & Alerts
Message
Priority
Flight
Instruments
VOICE ALERTS
Description
Flight
Planning
Procedures
MFD
Pop-Up Alert
Hazard
Avoidance
Aural
Message
Reduced Required Obstacle
Clearance Warning (ROC)
“Warning; Obstacle,
Obstacle”
Imminent Obstacle Impact
Warning (IOI)
“Warning; Obstacle,
Obstacle”
Reduced Required Terrain
Clearance Caution (RTC)
“Caution; Terrain,
Terrain”
Imminent Terrain Impact
Caution (ITI)
“Caution; Terrain,
Terrain”
Reduced Required Obstacle
Clearance Caution (ROC)
“Caution; Obstacle,
Obstacle”
77
Index
Garmin G1000 Cockpit Reference Guide for the Piper PA-44-180 Seminole
Appendix
“Warning; Terrain,
Terrain”
Annun/Alerts
Imminent Terrain Impact
Warning (ITI)
Abnormal
Operation
“Warning; Terrain,
Terrain”
Additional
Features
PFD/MFD
TERRAIN-SVT
Page
Annunciation
Reduced Required Terrain
Clearance Warning (RTC)
190-01462-00 Rev. A
GPS Nav
TERRAIN-SVT ALERTS
Alert Type
Nav/Com/
XPDR/Audio
Imminent stall is sensed by stall vane
Airspeed exceeds VNE
Warning Aircraft has descended below the preset barometric
“Minimums, minimums”
minimum descent altitude
“Check Gear”
Landing gear are not down and locked
“Traffic”
TIS Traffic Alert
“Traffic, (distance, bearing, altitude)” Caution TAS Traffic Alert
“Check Gear”
Landing gear are not down and locked
“TAS System Test Passed”
TAS system initiated test passed
“TAS System Test Failed”
TAS system initiated test failed
Aircraft is one minute from Top of Descent. Issued
“Vertical track”
Advisory
only when vertical navigation is enabled.
“TIS Not Available”
Aircraft is outside TIS coverage area
“Timer Expired”
Countdown timer on the PFD has reached zero
EIS
“Stall”
“Airspeed”
Index
Appendix
Annun/Alerts
Abnormal
Operation
Additional
Features
Hazard
Avoidance
Procedures
Flight
Planning
GPS Nav
Nav/Com/
XPDR/Audio
EIS
Flight
Instruments
Annunciations & Alerts
Alert Type
PFD/MFD
TERRAIN-SVT
Page
Annunciation
MFD
Pop-Up Alert
Imminent Obstacle Impact
Caution (IOI)
Aural
Message
“Caution; Obstacle,
Obstacle”
TERRAIN-SVT SYSTEM STATUS ANNUNCIATIONS
TERRAIN-SVT Page
Annunciation
Aural Message
TERRAIN TEST
None
None
“Terrain System
Test OK”
None
None
TERRAIN DATABASE FAILURE
None
Terrain System Test
Fail
TERRAIN FAIL
“Terrain System
Failure”
Terrain or Obstacle
database unavailable
or invalid,
invalid software
configuration, system
audio fault
TERRAIN FAIL
“Terrain System
Failure”
NO GPS POSITION
“Terrain System
Not Available”
None
“Terrain System
Not Available”
None
“Terrain System
Available”
Alert Type
PFD/MFD Alert
Annunciation
System Test in
Progress
System Test Pass
None
Terrain Alerting is
disabled
MFD Terrain or
Obstacle database
unavailable or invalid.
Terrain-SVS operating
with PFD Terrain or
Obstacle databases
None
No GPS position
Excessively degraded
GPS signal, Out of
database coverage
area
Sufficient GPS signal
received after loss
78
None
Garmin G1000 Cockpit Reference Guide for the Piper PA-44-180 Seminole
190-01462-00 Rev. A
Annunciations & Alerts
Alert Type
MFD
Pop-Up Alert
“Pull Up”
or
Imminent Obstacle
Impact Warning
(IOI)
or
or
“Terrain Ahead; Terrain Ahead”
or
“Caution, Terrain; Caution, Terrain”
or
“Caution, Obstacle; Caution,
Obstacle”
or
“Obstacle Ahead; Obstacle Ahead”
Appendix
Reduced Required
Obstacle Clearance
Caution (ROC)
or
“Caution, Terrain; Caution, Terrain”
or
“Terrain Ahead; Terrain Ahead”
Annun/Alerts
Imminent Terrain
Impact Caution
(ITI)
“Obstacle Ahead, Pull Up; Obstacle
Ahead, Pull Up”
or
“Obstacle, Obstacle; Pull Up, Pull
Up”
Abnormal
Operation
Reduced Required
Terrain Clearance
Caution (RTC)
“Obstacle, Obstacle; Pull Up, Pull
Up”
or
“Obstacle Ahead, Pull Up; Obstacle
Ahead, Pull Up”
Additional
Features
Reduced Required
Obstacle Clearance
Warning (ROC)
Terrain Ahead, Pull Up; Terrain
Ahead, Pull Up”
or
“Terrain, Terrain; Pull Up, Pull Up”
Hazard
Avoidance
or
Procedures
Imminent Terrain
Impact Warning
(ITI)
“Terrain, Terrain; Pull Up, Pull Up”
or
“Terrain Ahead, Pull Up; Terrain
Ahead, Pull Up”
Flight
Planning
or
GPS Nav
Reduced Required
Terrain Clearance
Warning (RTC)
Nav/Com/
XPDR/Audio
Excessive Descent
Rate Warning
(EDR)
Aural Message
EIS
PFD/MFD
TAWS-B Page
Annunciation
Flight
Instruments
TAWS-B ALERTS
Index
190-01462-00 Rev. A
Garmin G1000 Cockpit Reference Guide for the Piper PA-44-180 Seminole
79
Additional
Features
Hazard
Avoidance
Procedures
Flight
Planning
GPS Nav
Nav/Com/
XPDR/Audio
EIS
Flight
Instruments
Annunciations & Alerts
Alert Type
PFD/MFD
TAWS-B Page
Annunciation
Imminent Obstacle
Impact Caution
(IOI)
Abnormal
Operation
Annun/Alerts
Appendix
Aural Message
or
“Obstacle Ahead; Obstacle Ahead”
or
“Caution, Obstacle; Caution,
Obstacle”
Premature Descent
Alert Caution
(PDA)
Altitude Callout
“500”
“Too Low, Terrain”
None
None
“Five-Hundred”
Excessive Descent
Rate Caution
(EDR)
“Sink Rate”
Negative Climb
Rate Caution
(NCR)
“Don’t Sink”
or
“Too Low, Terrain”
or
TAWS-B SYSTEM STATUS ANNUNCIATIONS
Alert Type
PFD/MFD Alert
Annunciation
TAWS-B Page Annunciation
Aural Message
TAWS TEST
None
None
“TAWS System
Test OK”
None
None
TERRAIN DATABASE FAILURE
None
TAWS-B System Test Fail
TAWS FAIL
“TAWS System
Failure”
Terrain or Obstacle
database unavailable or
invalid, invalid software
configuration, system
audio fault
TAWS FAIL
“TAWS System
Failure”
System Test in Progress
System Test Pass
Index
MFD
Pop-Up Alert
None
TAWS Alerting is disabled
MFD Terrain or Obstacle
database unavailable or
invalid. TAWS operating
with PFD Terrain or
Obstacle databases
80
None
Garmin G1000 Cockpit Reference Guide for the Piper PA-44-180 Seminole
190-01462-00 Rev. A
Annunciations & Alerts
No GPS position
Aural Message
NO GPS POSITION
“TAWS Not
Available”
None
“TAWS Not
Available”
None
“TAWS Available”
Sufficient GPS signal
received after loss
None
Nav/Com/
XPDR/Audio
Excessively degraded
GPS signal, Out of
database coverage area
EIS
TAWS-B Page Annunciation
Flight
Instruments
PFD/MFD Alert
Annunciation
Alert Type
GPS Nav
GDL 69/69A DATA LINK RECEIVER MESSAGES
Message Location
Description
CHECK ANTENNA
XM Information Page
(MFD)
Data Link Receiver antenna
error; service required
UPDATING
XM Information Page
(MFD))
Data Link Receiver updating
encryption code
NO SIGNAL
XM Information Page
Weather Datalink Page
(MFD)
Loss of signal; signal strength
too low for receiver
LOADING
XM Radio Page (MFD)
Acquiring channel audio or
information
OFF AIR
XM Radio Page (MFD)
Channel not in service
--------
XM Radio Page (MFD)
Missing channel information
WEATHER DATA LINK FAILED
Weather Datalink Page
(MFD)
No communication from Data
Link Receiver within last 5
minutes
ACTIVATION REQUIRED
XM Information Page
(MFD)
SiriusXM subscription is not
activated
DETECTING ACTIVATION
Weather Datalink Page
(MFD)
SiriusXM subscription is
activating.
WAITING FOR DATA...
Weather Datalink Page
(MFD)
SiriusXM subscription
confirmed downloading
weather data.
Flight
Planning
Message
Procedures
Hazard
Avoidance
Additional
Features
Abnormal
Operation
Annun/Alerts
Appendix
Index
190-01462-00 Rev. A
Garmin G1000 Cockpit Reference Guide for the Piper PA-44-180 Seminole
81
Index
Appendix
Annun/Alerts
Abnormal
Operation
Additional
Features
Hazard
Avoidance
Procedures
Flight
Planning
GPS Nav
Nav/Com/
XPDR/Audio
EIS
Flight
Instruments
Annunciations & Alerts
MFD & PFD MESSAGE ADVISORIES
Message
DATA LOST – Pilot stored data
was lost. Recheck settings.
XTALK ERROR – A flight display
crosstalk error has occurred.
PFD1 SERVICE – PFD1 needs
service. Return unit for repair.
MFD1 SERVICE – MFD1 needs
service. Return unit for repair.
MANIFEST – PFD1 software
mismatch, communication halted.
MANIFEST – MFD1 software
mismatch, communication halted.
PFD1 CONFIG – PFD1 config error.
Config service req’d.
MFD1 CONFIG – MFD1 config
error. Config service req’d.
SW MISMATCH – GDU software
version mismatch. Xtalk is off.
PFD1 COOLING – PFD1 has poor
cooling. Reducing power usage.
MFD1 COOLING – MFD1 has poor
cooling. Reducing power usage.
PFD1 KEYSTK – PFD1 [key name]
Key is stuck.
MFD1 KEYSTK – MFD [key name]
Key is stuck.
82
Comments
The pilot profile data was lost. System reverts
to default pilot profile and settings. The pilot
may reconfigure the MFD & PFDs with preferred
settings, if desired.
The MFD and PFD are not communicating with
each other. The system should be serviced.
The PFD and/or MFD self-test has detected a
problem. The system should be serviced.
The PFD and/or MFD has incorrect software
installed. The system should be serviced.
The PFD configuration settings do not match
backup configuration memory. The system
should be serviced.
The MFD configuration settings do not match
backup configuration memory. The system
should be serviced.
The MFD and PFD have different software
versions installed. The system should be serviced.
The PFD and/or MFD is overheating and is
reducing power consumption by dimming the
display. If problem persists, the system should
be serviced.
A key is stuck on the PFD and/or MFD bezel.
Attempt to free the stuck key by pressing it
several times. The system should be serviced if
the problem persists.
Garmin G1000 Cockpit Reference Guide for the Piper PA-44-180 Seminole
190-01462-00 Rev. A
Annunciations & Alerts
Flight
Instruments
Comments
The PFD1 configuration module backup memory
has failed. The system should be serviced.
The PFD1 voltage is low. The system should be
serviced.
The MFD voltage is low. The system should be
serviced.
EIS
Nav/Com/
XPDR/Audio
Message
CNFG MODULE – PFD1
configuration module is inoperative.
PFD1 VOLTAGE – PFD1 has low
voltage. Reducing power usage
MFD1 VOLTAGE – MFD1 has low
voltage. Reducing power usage
The MFD and/or PFD detected a failure in the
navigation database. Attempt to reload the
navigation database. If problem persists, the
system should be serviced.
Procedures
The MFD and/or PFD detected a failure in the
basemap database.
Hazard
Avoidance
The MFD and/or PFD detected a failure in the
terrain database. Ensure that the terrain card
is properly inserted in display. Replace terrain
card. If problem persists, the system should be
serviced.
Additional
Features
Abnormal
Operation
The terrain database is present on another LRU,
but is missing on the specified LRU.
Annun/Alerts
The MFD and/or PFD detected a failure in the
obstacle database. Ensure that the data card is
properly inserted. Replace data card. If problem
persists, the system should be serviced.
Appendix
MFD1 DB ERR – MFD1 terrain
database missing.
PFD1 DB ERR – PFD1 terrain
database missing.
MFD1 DB ERR – MFD1 obstacle
database error exists.
PFD1 DB ERR – PFD1 obstacle
database error exists.
Comments
Flight
Planning
Message
MFD1 DB ERR – MFD1 navigation
database error exists.
PFD1 DB ERR – PFD1 navigation
database error exists.
MFD1 DB ERR – MFD1 basemap
database error exists.
PFD1 DB ERR – PFD1 basemap
database error exists.
MFD1 DB ERR – MFD1 terrain
database error exists.
PFD1 DB ERR – PFD1 terrain
database error exists.
GPS Nav
DATABASE MESSAGE ADVISORIES
Index
190-01462-00 Rev. A
Garmin G1000 Cockpit Reference Guide for the Piper PA-44-180 Seminole
83
Message
MFD1 DB ERR – MFD1 obstacle
database missing.
PFD1 DB ERR – PFD1 obstacle
database missing.
MFD1 DB ERR – MFD1 airport
terrain database error exists.
PFD1 DB ERR – PFD1 airport
terrain database error exists.
MFD1 DB ERR – MFD1 airport
terrain database missing.
PFD1 DB ERR – PFD1 airport
terrain database missing.
MFD1 DB ERR – MFD1 Safe Taxi
database error exists.
PFD1 DB ERR – PFD1 Safe Taxi
database error exists.
MFD1 DB ERR – MFD1 Chartview
database error exists.
Comments
The obstacle database is present on another LRU,
but is missing on the specified LRU.
The MFD and/or PFD detected a failure in the
airport terrain database. Ensure that the data
card is properly inserted. Replace data card. If
problem persists, the system should be serviced.
The airport terrain database is present on
another LRU, but is missing on the specified LRU.
The MFD and/or PFD detected a failure in the
SafeTaxi database. Ensure that the data card is
properly inserted. Replace data card. If problem
persists, the system should be serviced.
The MFD detected a failure in the ChartView
database (optional feature). Ensure the data card
is properly inserted. Replace data card. If problem
persists, system should be serviced.
MFD1 DB ERR – MFD1 FliteCharts The MFD detected a failure in the FliteCharts
database error exists.
database (optional feature). Ensure the data card
is properly inserted. Replace data card. If problem
persists, system should be serviced.
MFD1 DB ERR – MFD1 Airport
The MFD detected a failure in the Airport Directory
Directory database error exists.
database. Ensure that the data card is properly
inserted. Replace data card. If problem persists,
the system should be serviced.
Index
Appendix
Annun/Alerts
Abnormal
Operation
Additional
Features
Hazard
Avoidance
Procedures
Flight
Planning
GPS Nav
Nav/Com/
XPDR/Audio
EIS
Flight
Instruments
Annunciations & Alerts
84
Garmin G1000 Cockpit Reference Guide for the Piper PA-44-180 Seminole
190-01462-00 Rev. A
Annunciations & Alerts
EIS
Nav/Com/
XPDR/Audio
GPS Nav
Flight
Planning
Procedures
Hazard
Avoidance
Additional
Features
Abnormal
Operation
Annun/Alerts
Appendix
Comments
The PFD and MFD have different navigation
database versions or regions installed. Crossfill
is off. Check the AUX-SYSTEM STATUS Page
to determine versions or regions. Also, check
the AUX-SYSTEM STATUS Page for a database
synchronization function not completed. After
synchronization is complete, power must be
turned off, then on.
DB MISMATCH – Standby
The PFD and MFD have different standby
Navigation database mismatch.
navigation database versions or regions installed.
Check the AUX-SYSTEM STATUS Page to
determine versions or regions. Also, check the
AUX-SYSTEM STATUS Page for a database
synchronization function not completed. After
synchronization is complete, power must be
turned off, then on.
DB MISMATCH – Terrain database The PFDs and MFD have different terrain database
mismatch.
versions or types installed. Install correct terrain
database version or type in all displays. Check the
AUX-SYSTEM STATUS Page to determine versions
or regions. Also, check the AUX-SYSTEM STATUS
Page for a database synchronization function not
completed. After synchronization is complete,
power must be turned off, then on.
DB MISMATCH – Obstacle
The PFDs and MFD have different obstacle
database mismatch.
database installed. Install correct obstacle
database in all displays. Check the AUX-SYSTEM
STATUS Page to determine versions or regions.
Also, check the AUX-SYSTEM STATUS Page
for a database synchronization function not
completed. After synchronization is complete,
power must be turned off, then on.
Flight
Instruments
Message
DB MISMATCH – Navigation
database version mismatch. Xtalk
is off.
Index
190-01462-00 Rev. A
Garmin G1000 Cockpit Reference Guide for the Piper PA-44-180 Seminole
85
Message
DB MISMATCH – Airport Terrain
database mismatch.
NAV DB UPDATED – Active
navigation database updated.
TERRAIN DISABLED – Terrain
Awareness DB resolution too low.
TERRAIN DSP – [PFD1 or
MFD1] Terrain awareness display
unavailable.
Comments
The PFD and MFD have different airport terrain
databases installed. Check the AUX-SYSTEM
STATUS Page to determine versions or regions.
Also, check the AUX-SYSTEM STATUS Page
for a database synchronization function not
completed. After synchronization is complete,
power must be turned off, then on.
System has updated the active navigation
database from the standby navigation database.
Terrain database of sufficient resolution (9 arcsecond or better) is not currently installed.
One of the terrain, airport terrain, or obstacle
databases required for TAWS in the specified PFD
or MFD is missing or invalid.
GMA 1347 MESSAGE ADVISORIES
Message
Comments
GMA1 FAIL – GMA1 is inoperative. The audio panel self-test has detected a failure.
The audio panel is unavailable. The system
should be serviced.
GMA1 CONFIG – GMA1 config
The audio panel configuration settings do not
error. Config service req’d.
match backup configuration memory. The system
should be serviced.
The audio panel has incorrect software installed. The
MANIFEST – GMA1 software
system should be serviced.
mismatch, communication halted.
The audio panel self-test has detected a problem
GMA1 SERVICE – GMA1 needs
in the unit. Certain audio functions may still be
service. Return unit for repair.
available, and the audio panel may still be usable.
The system should be serviced when possible.
Index
Appendix
Annun/Alerts
Abnormal
Operation
Additional
Features
Hazard
Avoidance
Procedures
Flight
Planning
GPS Nav
Nav/Com/
XPDR/Audio
EIS
Flight
Instruments
Annunciations & Alerts
86
Garmin G1000 Cockpit Reference Guide for the Piper PA-44-180 Seminole
190-01462-00 Rev. A
Annunciations & Alerts
The GIA1 and/or GIA2 configuration settings do
not match backup configuration memory. The
system should be serviced.
Flight
Planning
The GIA1 and/or GIA2 temperature is too low
to operate correctly. Allow units to warm up to
operating temperature.
GPS Nav
The GIA1 and/or GIA2 have an error in the audio
configuration. The system should be serviced.
Nav/Com/
XPDR/Audio
Procedures
The GIA1 and/or GIA2 temperature is too
high. If problem persists, the system should be
serviced.
Hazard
Avoidance
The GIA1 and/or GIA2 self-test has detected
a problem in the unit. The system should be
serviced.
Additional
Features
Abnormal
Operation
A GIA mismatch has been detected, where only
one is SBAS capable.
Annun/Alerts
Appendix
The GIA1 and/or GIA 2 has incorrect software
installed. The system should be serviced.
Garmin G1000 Cockpit Reference Guide for the Piper PA-44-180 Seminole
Index
190-01462-00 Rev. A
Comments
EIS
Message
GIA1 CONFIG – GIA1 config error.
Config service req’d.
GIA2 CONFIG – GIA2 config error.
Config service req’d.
GIA1 CONFIG – GIA1 audio config
error. Config service req’d.
GIA2 CONFIG – GIA2 audio config
error. Config service req’d.
GIA1 COOLING – GIA1
temperature too low.
GIA2 COOLING – GIA2
temperature too low.
GIA1 COOLING – GIA1 over
temperature.
GIA2 COOLING – GIA2 over
temperature.
GIA1 SERVICE – GIA1 needs
service. Return the unit for repair.
GIA2 SERVICE – GIA2 needs
service. Return the unit for repair.
HW MISMATCH – GIA hardware
mismatch. GIA1 communication
halted.
HW MISMATCH – GIA hardware
mismatch. GIA2 communication
halted.
MANIFEST – GIA1 software
mismatch, communication halted.
MANIFEST – GIA2 software
mismatch, communication halted.
Flight
Instruments
GIA 63W MESSAGE ADVISORIES
87
Index
Appendix
Annun/Alerts
Abnormal
Operation
Additional
Features
Hazard
Avoidance
Procedures
Flight
Planning
GPS Nav
Nav/Com/
XPDR/Audio
EIS
Flight
Instruments
Annunciations & Alerts
Message
MANIFEST – GFC software
mismatch, communication halted.
MANIFEST – COM1 software
mismatch, communication halted.
MANIFEST – COM2 software
mismatch, communication halted.
MANIFEST – NAV1 software
mismatch, communication halted.
MANIFEST – NAV2 software
mismatch, communication halted.
COM1 CONFIG – COM1 config
error. Config service req’d..
COM2 CONFIG – COM2 config
error. Config service req’d.
COM1 TEMP – COM1 over temp.
Reducing transmitter power.
COM2 TEMP – COM2 over temp.
Reducing transmitter power.
COM1 SERVICE – COM1 needs
service. Return unit for repair.
COM2 SERVICE – COM2 needs
service. Return unit for repair.
COM1 PTT – COM1 push-to-talk
key is stuck.
COM2 PTT – COM2 push-to-talk
key is stuck.
COM1 RMT XFR – COM1 remote
transfer key is stuck.
COM2 RMT XFR – COM2 remote
transfer key is stuck.
88
Comments
Incorrect servo software is installed, or gain
settings are incorrect.
The COM1 and/or COM2 has incorrect software
installed. The system should be serviced.
The NAV1 and/or NAV2 has incorrect software
installed. The system should be serviced.
The COM1 and/or COM2 configuration settings
do not match backup configuration memory. The
system should be serviced.
The system has detected an over temperature
condition in COM1 and/or COM2. The
transmitter is operating at reduced power. If the
problem persists, the system should be serviced.
The system has detected a failure in COM1 and/
or COM2. COM1 and/or COM2 may still be
usable. The system should be serviced when
possible.
The COM1 and/or COM2 external push-to-talk
switch is stuck in the enable (or “pressed”)
position. Press the PTT switch again to cycle its
operation.
If the problem persists, the system should be
serviced.
The COM1 and/or COM2 transfer switch is stuck
in the enabled (or “pressed”) position. Press
the transfer switch again to cycle its operation.
If the problem persists, the system should be
serviced.
Garmin G1000 Cockpit Reference Guide for the Piper PA-44-180 Seminole
190-01462-00 Rev. A
Annunciations & Alerts
Loss of GPS navigation due to GPS failure.
Abort approach due to loss of GPS navigation.
Vertical guidance generated by SBAS is
unavailable, use LNAV only minimums.
Displayed after passing the first waypoint of a
true north approach when the nav angle is set
to ‘AUTO’.
Flight
Planning
Procedures
A failure has been detected in the GPS1 and/
or GPS2 receiver. The receiver may still be
available. The system should be serviced.
Hazard
Avoidance
Additional
Features
A failure has been detected in the NAV1 and/
or NAV2 receiver. The receiver may still be
available. The system should be serviced.
Abnormal
Operation
Garmin G1000 Cockpit Reference Guide for the Piper PA-44-180 Seminole
Index
A failure has been detected in glideslope
receiver 1 and/or receiver 2. The system should
be serviced.
Appendix
The remote NAV1 and/or NAV2 transfer switch is
stuck in the enabled (or “pressed”) state. Press
the transfer switch again to cycle its operation.
If the problem persists, the system should be
serviced.
Annun/Alerts
190-01462-00 Rev. A
Loss of GPS navigation due to position error.
GPS Nav
G/S2 FAIL – G/S2 is inoperative.
Nav/Com/
XPDR/Audio
G/S1 FAIL – G/S1 is inoperative.
EIS
GPS1 SERVICE – GPS1 needs
service. Return unit for repair.
GPS2 SERVICE – GPS2 needs
service. Return unit for repair.
NAV1 SERVICE – NAV1 needs
service. Return unit for repair.
NAV2 SERVICE – NAV2 needs
service. Return unit for repair.
NAV1 RMT XFR – NAV1 remote
transfer key is stuck.
NAV2 RMT XFR – NAV2 remote
transfer key is stuck.
Comments
GPS integrity is insufficient for the current phase
of flight.
Loss of GPS navigation due to insufficient
satellites.
Flight
Instruments
Message
LOI – GPS integrity lost. Crosscheck
with other NAVS.
GPS NAV LOST – Loss of GPS
navigation. Insufficient satellites.
GPS NAV LOST – Loss of GPS
navigation. Position error.
GPS NAV LOST – Loss of GPS
navigation. GPS fail.
ABORT APR – Loss of GPS
navigation. Abort approach.
APR DWNGRADE – Approach
downgraded.
TRUE APR – True north approach.
Change HDG reference to TRUE.
89
Index
Appendix
Annun/Alerts
Abnormal
Operation
Additional
Features
Hazard
Avoidance
Procedures
Flight
Planning
GPS Nav
Nav/Com/
XPDR/Audio
EIS
Flight
Instruments
Annunciations & Alerts
Message
G/S1 SERVICE – G/S1 needs
service. Return unit for repair.
G/S2 SERVICE – G/S2 needs
service. Return unit for repair.
TRN AUD FAIL – Trn Awareness
audio source unavailable.
TERRAIN AUD CFG – Trn
Awareness audio config error.
Service req’d.
Comments
A failure has been detected in glideslope
receiver 1 and/or receiver 2. The receiver may
still be available. The system should be serviced
when possible.
The audio source for terrain awareness is offline.
Check GIA1 or GIA 2.
Terrain audio alerts are not configured properly.
The system should be serviced.
GEA 71 MESSAGE ADVISORIES
Message
Comments
GEA1 CONFIG – GEA1 config error. The GEA1 configuration settings do not match
Config service req’d.
those of backup configuration memory. The
G1000 system should be serviced.
MANIFEST – GEA1 software
The #1 GEA 71 has incorrect software installed.
mismatch, communication halted. The G1000 system should be serviced.
GTX 33/33 W/ES MESSAGE ADVISORIES
Message
XPDR1 CONFIG – XPDR1 config
error. Config service req’d.
Comments
The transponder configuration settings do not
match those of backup configuration memory.
The system should be serviced.
MANIFEST – GTX1 software
The transponder has incorrect software installed.
mismatch, communication halted.
The system should be serviced.
XPDR1 SRVC – XPDR1 needs
The #1 transponder should be serviced when
service. Return unit for repair.
possible.
XPDR1 FAIL – XPDR1 is
There is no communication with the #1
inoperative.
transponder.
XPDR1 ADS-B FAIL – XPDR1
ADS-B is inoperative. Other transponder functions
unable to transmit ADS-B messages. may be available. Service when possible.
90
Garmin G1000 Cockpit Reference Guide for the Piper PA-44-180 Seminole
190-01462-00 Rev. A
Annunciations & Alerts
Hazard
Avoidance
Additional
Features
Abnormal
Operation
Annun/Alerts
MANIFEST – GRS1 software
mismatch, communication halted.
Procedures
GEO LIMITS – AHRS1 too far
North/South, no magnetic compass.
Flight
Planning
AHRS1 GPS – AHRS1 not receiving
backup GPS information.
AHRS1 GPS – AHRS1 operating
exclusively in no-GPS mode.
AHRS1 SERVICE – AHRS1 needs
service. Return unit for repair.
AHRS1 SRVC – AHRS1 Magneticfield model needs update.
AHRS1 CONFIG – AHRS1 config
error. Config service req’d.
GPS Nav
AHRS1 GPS – AHRS1 not receiving
any GPS information.
Nav/Com/
XPDR/Audio
AHRS1 GPS – AHRS1 using backup
GPS source.
Comments
The #1 AHRS is not receiving true airspeed from
the air data computer. The AHRS relies on GPS
information to augment the lack of airspeed.
The system should be serviced.
The #1 AHRS is using the backup GPS path.
Primary GPS path has failed. The system should
be serviced when possible.
The #1 AHRS is not receiving any or any useful
GPS information. Check AFMS limitations. The
system should be serviced.
The #1 AHRS is not receiving backup GPS
information. The system should be serviced.
The #1 AHRS is operating exclusively in no-GPS
mode. The system should be serviced.
A failure has been detected in the #1 AHRS. The
system should be serviced.
The #1 AHRS earth magnetic field model is out of
date. Update magnetic field model when practical.
AHRS configuration settings do not match those
of backup configuration memory. The system
should be serviced.
The aircraft is outside geographical limits for
approved AHRS operation. Heading is flagged
as invalid.
The #1 AHRS has incorrect software installed.
The system should be serviced.
EIS
Message
AHRS1 TAS – AHRS1 not receiving
airspeed.
Flight
Instruments
GRS 77 MESSAGE ADVISORIES
Appendix
Index
190-01462-00 Rev. A
Garmin G1000 Cockpit Reference Guide for the Piper PA-44-180 Seminole
91
GMU 44 MESSAGE ADVISORIES
Message
HDG FAULT – AHRS1
magnetometer fault has occurred.
MANIFEST – GMU1 software
mismatch, communication halted.
Flight
Planning
GDL69 FAIL – GDL 69 has failed.
Annun/Alerts
Abnormal
Operation
Additional
Features
Hazard
Avoidance
Message
GDL69 CONFIG – GDL 69 config
error. Config service req’d.
MANIFEST – GDL software
mismatch, communication halted.
Comments
GDL 69 configuration settings do not match
those of backup configuration memory. The
system should be serviced.
A failure has been detected in the GDL 69. The
receiver is unavailable. The system should be
serviced
The GDL 69 has incorrect software installed.
The system should be serviced.
GTS 800 MESSAGE ADVISORIES
Message
GTS CONFIG – GTS config error.
Config service req’d.
MANIFEST – GTS software
mismatch, communication halted.
Comments
The GTS and GDU have incompatible
configurations. This alert is also set when the
GTS has an invalid mode S address configured or
the mode S address does not match both XPDR
mode S addresses.
The GTS has incorrect software installed. The
system should be serviced.
Index
Appendix
Comments
A fault has occurred in the #1 GMU 44.
Heading is flagged as invalid. The AHRS uses
GPS for backup mode operation. The G1000
system should be serviced.
The GMU 44 has incorrect software installed.
The G1000 system should be serviced.
GDL 69A MESSAGE ADVISORIES
Procedures
GPS Nav
Nav/Com/
XPDR/Audio
EIS
Flight
Instruments
Annunciations & Alerts
92
Garmin G1000 Cockpit Reference Guide for the Piper PA-44-180 Seminole
190-01462-00 Rev. A
Annunciations & Alerts
Comments
The GDC 74A has incorrect software installed.
The system should be serviced.
EIS
Message
MANIFEST – GDC1 software
mismatch, communication halted.
Flight
Instruments
GDC 74A MESSAGE ADVISORIES
Flight
Planning
Procedures
Hazard
Avoidance
Additional
Features
Abnormal
Operation
Annun/Alerts
Appendix
Comments
Upon power-up, the system detects that a
stored flight plan waypoint is locked. This
occurs when an navigation database update
eliminates an obsolete waypoint. The flight
plan cannot find the specified waypoint and
flags this message. This can also occur with
user waypoints in a flight plan that is deleted.
Remove the waypoint from the flight plan if it
no longer exists in any database,
Or
update the waypoint name/identifier to reflect
the new information.
FPL WPT MOVE – Flight plan
The system has detected that a waypoint
waypoint moved.
coordinate has changed due to a new navigation
database update. Verify that stored flight plans
contain correct waypoint locations.
TIMER EXPIRD – Timer has expired. The system notifies the pilot that the timer has
expired.
DB CHANGE – Database changed. This occurs when a stored flight plan contains
Verify user modified procedures.
procedures that have been manually edited.
This alert is issued only after an navigation
database update. Verify that the user-modified
procedures in stored flight plans are correct and
up to date.
GPS Nav
Message
FPL WPT LOCK – Flight plan
waypoint is locked.
Nav/Com/
XPDR/Audio
MISCELLANEOUS MESSAGE ADVISORIES
Index
190-01462-00 Rev. A
Garmin G1000 Cockpit Reference Guide for the Piper PA-44-180 Seminole
93
Message
DB CHANGE – Database changed.
Verify stored airways.
Comments
This occurs when a stored flight plan contains
an airway that is no longer consistent with the
navigation database. This alert is issued only
after an navigation database update. Verify
use of airways in stored flight plans and reload
airways as needed.
FPL TRUNC – Flight plan has been This occurs when a newly installed navigation
truncated.
database eliminates an obsolete approach
or arrival used by a stored flight plan. The
obsolete procedure is removed from the flight
plan. Update flight plan with current arrival or
approach.
WPT ARRIVAL – Arriving at
Arriving at waypoint [xxxx], where [xxxx] is the
waypoint -[xxxx]
waypoint name.
STEEP TURN – Steep turn ahead.
A steep turn is 15 seconds ahead. Prepare to
turn.
INSIDE ARSPC – Inside airspace.
The aircraft is inside the airspace.
ARSPC AHEAD – Airspace ahead
Special use airspace is ahead of aircraft. The
less than 10 minutes.
aircraft will penetrate the airspace within 10
minutes.
ARSPC NEAR – Airspace near and Special use airspace is near and ahead of the
ahead.
aircraft position.
ARSPC NEAR – Airspace near – less Special use airspace is within 2 nm of the
than 2 nm.
aircraft position.
APR INACTV – Approach is not
The system notifies the pilot that the loaded
active.
approach is not active. Activate approach when
required.
SLCT FREQ – Select appropriate
The system notifies the pilot to load the
frequency for approach.
approach frequency for the appropriate NAV
receiver. Select the correct frequency for the
approach.
Index
Appendix
Annun/Alerts
Abnormal
Operation
Additional
Features
Hazard
Avoidance
Procedures
Flight
Planning
GPS Nav
Nav/Com/
XPDR/Audio
EIS
Flight
Instruments
Annunciations & Alerts
94
Garmin G1000 Cockpit Reference Guide for the Piper PA-44-180 Seminole
190-01462-00 Rev. A
Annunciations & Alerts
Additional
Features
Abnormal
Operation
Annun/Alerts
Appendix
Index
95
Hazard
Avoidance
Garmin G1000 Cockpit Reference Guide for the Piper PA-44-180 Seminole
Procedures
190-01462-00 Rev. A
Flight
Planning
VNV – Unavailable. Excessive
crosstrack error.
VNV – Unavailable. Parallel course
selected.
IAF waypoint for parallel offset has been
passed.
IAF waypoint for parallel offset has been
passed.
The position of the selected waypoint [xxxx]
is not calculated based on the WGS84 map
reference datum and may be positioned in error
as displayed. Do not use GPS to navigate to
the selected non-WGS84 waypoint.
Stormscope has failed. The G1000 system
should be serviced.
The current vertical waypoint can not be
reached within the maximum flight path angle
and vertical speed constraints. The system
automatically transitions to the next vertical
waypoint.
The current track angle error exceeds the limit,
causing the vertical deviation to go invalid.
The lateral flight plan contains a procedure
turn, vector, or other unsupported leg type
prior to the active vertical waypoint. This
prevents vertical guidance to the active vertical
waypoint.
The current crosstrack exceeds the limit, causing
vertical deviation to go invalid.
A parallel course has been selected, causing the
vertical deviation to go invalid.
GPS Nav
VNV – Unavailable. Excessive track
angle error.
VNV – Unavailable. Unsupported
leg type in flight plan.
Bad parallel track geometry.
Nav/Com/
XPDR/Audio
STRMSCP FAIL – Stormscope has
failed.
UNABLE V WPT – Can’t reach
current vertical waypoint.
Comments
The system notifies the pilot to set the CDI to
the correct NAV receiver. Set the CDI to the
correct NAV receiver.
EIS
PTK FAIL – Parallel track
unavailable: bad geometry.
PTK FAIL – Parallel track
unavailable: past IAF.
PTK FAIL – Parallel track
unavailable: past IAF.
NON WGS84 WPT – Do not use
GPS for navigation to [xxxx]
Flight
Instruments
Message
SLCT NAV – Select NAV on CDI for
approach.
Index
Appendix
Annun/Alerts
Abnormal
Operation
Additional
Features
Hazard
Avoidance
Procedures
Flight
Planning
GPS Nav
Nav/Com/
XPDR/Audio
EIS
Flight
Instruments
Annunciations & Alerts
Message
TRAFFIC FAIL – Traffic device has
failed.
Comments
The system is no longer receiving data from
the traffic system. The traffic device should be
serviced.
FAILED PATH – A data path has
A data path connected to the GDU, GSD 41, or
failed.
the GIA 63W has failed.
MAG VAR WARN – Large magnetic The GDU’s internal model cannot determine
variance. Verify all course angles.
the exact magnetic variance for geographic
locations near the magnetic poles. Displayed
magnetic course angles may differ from the
actual magnetic heading by more than 2°.
SVT DISABLED – Out of available
Synthetic Vision is disabled because the aircraft
terrain region.
is not within the boundaries of the installed
terrain database.
SVT DISABLED – Terrain DB
Synthetic Vision is disabled because a terrain
resolution too low.
database of sufficient resolution (9 arc-second
or better) is not currently installed.
SCHEDULER [#] – <message>.
Message criteria entered by the user.
CHECK CRS – Database course for Selected course for LOC1 differs from published
LOC1 / [LOC ID] is [CRS]°.
localizer course by more than 10 degrees.
CHECK CRS – Database course for Selected course for LOC2 differs from published
LOC2 / [LOC ID] is [CRS]°.
localizer course by more than 10 degrees.
HOLD EXPIRED – Holding EFC time Expect Further Clearance (EFC) time has expired
expired.
for the User Defined Hold.
[PFD1 or MFD1] CARD 1 REM –
The SD card was removed from the top card
Card 1 was removed. Reinsert card. slot of the PFD or MFD. The SD card needs to
be reinserted.
[PFD1 or MFD1] CARD 2 REM –
The SD card was removed from the bottom card
Card 2 was removed. Reinsert card. slot of the PFD or MFD. The SD card needs to
be reinserted.
[PFD1 or MFD1] CARD 1 ERR –
The SD card in the top card slot of the PFD or
Card 1 is invalid.
MFD contains invalid data.
[PFD1 or MFD1] CARD 2 ERR –
The SD card in the bottom card slot of the PFD
Card 2 is invalid.
or MFD contains invalid data.
96
Garmin G1000 Cockpit Reference Guide for the Piper PA-44-180 Seminole
190-01462-00 Rev. A
Annunciations & Alerts
Flight
Instruments
FLIGHT PLAN IMPORT/EXPORT MESSAGES
In some circumstances, some messages may appear in conjunction with others.
Procedures
Hazard
Avoidance
Additional
Features
Abnormal
Operation
Annun/Alerts
Appendix
Index
97
Flight
Planning
Garmin G1000 Cockpit Reference Guide for the Piper PA-44-180 Seminole
GPS Nav
190-01462-00 Rev. A
Nav/Com/
XPDR/Audio
Description
A flight plan file stored on the SD card was
successfully imported as a stored flight
plan.
‘File contained user waypoints only.
The file stored on the SD card did not
User waypoints imported successfully.
contain a flight plan, only user waypoints.
No stored flight plan data was modified.’ These waypoints have been saved to the
system user waypoints. No flight plans
stored in the system have been modified.
‘No flight plan files found to import.’
The SD card contains no flight plan data.
‘Flight plan import failed.’
Flight plan data was not successfully
imported from the SD card.
‘Flight plan partially imported.’
Some flight plan waypoints were
successfully imported from the SD card,
however others had errors and were not
imported. A partial stored flight plan now
exists in the system.
‘File contained user waypoints only.’
The file stored on the SD card did not
contain a flight plan, only user waypoints.
One or more of these waypoints did not
import successfully.
‘Too many points. Flight plan truncated.’ The flight plan on the SD card contains
more waypoints than the system can
support. The flight plan was imported with
as many waypoints as possible.
‘Some waypoints not loaded. Waypoints The flight plan on the SD card contains one
locked.’
or more waypoints that the system cannot
find in the navigation database. The flight
plan has been imported, but must be edited
within the system before it can be activated
for use.
EIS
Flight Plan Import/Export Results
‘Flight plan successfully imported.’
Flight Plan Import/Export Results
‘User waypoint database full. Not all
loaded.’
‘One or more user waypoints renamed.’
‘Flight plan successfully exported.’
‘Flight plan export failed.’
Description
The flight plan file on the SD card contains
user waypoints. The quantity of stored user
waypoints has exceeded system capacity,
therefore not all the user waypoints on the
SD card have been imported. Any flight
plan user waypoints that were not imported
are locked in the flight plan. The flight plan
must be edited within the system before it
can be activated for use.
One or more imported user waypoints were
renamed when imported due to naming
conflicts with waypoints already existing in
the system.
The stored flight plan was successfully
exported to the SD card.
The stored flight plan was not successfully
exported to the SD card. The SD card may
not have sufficient available memory or the
card may have been removed prematurely.
Index
Appendix
Annun/Alerts
Abnormal
Operation
Additional
Features
Hazard
Avoidance
Procedures
Flight
Planning
GPS Nav
Nav/Com/
XPDR/Audio
EIS
Flight
Instruments
Annunciations & Alerts
98
Garmin G1000 Cockpit Reference Guide for the Piper PA-44-180 Seminole
190-01462-00 Rev. A
Annunciations & Alerts
EIS
Nav/Com/
XPDR/Audio
GPS Nav
Flight
Planning
Procedures
Hazard
Avoidance
Pilot Profile Import/Export Results
Description
‘No pilot profile plan files found to
Displayed if the SD card does not have one
import.’
or more valid pilot profile filenames.
‘Overwrite existing profile?’
Displayed if the profile name matches the
name of existing profile.
‘Profile name invalid. Enter a different
Displayed if the profile name is invalid.
profile name.’
‘All available pilot profiles in use. Delete Displayed if the maximum number for pilot
a profile before importing another.’
profiles has been reached.
‘Pilot profile import failed.’
Displayed if the importing operation fails
for any other reason.
‘Pilot profile import succeeded.’
Displayed if the importing operation
succeeds.
‘Overwrite existing file?’
Displayed if the filename matches the name
of an existing file on the SD card.
‘Pilot profile export failed.’
Displayed if the export operation fails.
‘Pilot profile export succeeded.’
Displayed if the export operation succeeds.
Flight
Instruments
PILOT PROFILE IMPORT/EXPORT MESSAGES
Additional
Features
Abnormal
Operation
Annun/Alerts
Appendix
Index
190-01462-00 Rev. A
Garmin G1000 Cockpit Reference Guide for the Piper PA-44-180 Seminole
99
Index
Appendix
Annun/Alerts
Abnormal
Operation
Additional
Features
Hazard
Avoidance
Procedures
Flight
Planning
GPS Nav
Nav/Com/
XPDR/Audio
EIS
Flight
Instruments
Annunciations & Alerts
Blank Page
100
Garmin G1000 Cockpit Reference Guide for the Piper PA-44-180 Seminole
190-01462-00 Rev. A
Appendix
Flight
Instruments
APPENDIX
PFD SOFTKEY MAP
EIS
CAS
Nav/Com/
XPDR/Audio
CAS ↑
CAS ↓
GPS Nav
Flight
Planning
Top Level PFD Softkeys
Procedures
WX LGND
METAR
Select the BACK or OFF Softkey
to return to the top-level softkeys.
TRFC-2
Hazard
Avoidance
TRFC-1
Additional
Features
Inset Map Softkeys
Level 2
CAS ↓
OFF
190-01462-00 Rev. A
Removes Inset Map
Garmin G1000 Cockpit Reference Guide for the Piper PA-44-180 Seminole
101
Index
INSET
Displayed only when a sufficient number of items
are displayed in the Annunciation Window to
warrant scrolling
When available, scrolls up through the alerts when
pressed
When available, scrolls down through the alerts
when pressed
Displays Inset Map in PFD lower left corner
Appendix
CAS ↑
Description
Annun/Alerts
CAS
Abnormal
Operation
Level 1
Level 1
Level 2
Description
DCLTR (3) Selects desired amount of map detail; cycles
through declutter levels:
DCLTR (No Declutter): All map features visible
DCLTR-1: Declutters land data
DCLTR-2: Declutters land and SUA data
DCLTR-3: Removes everything except the active
flight plan
WX LGND Displays icon and age on the Inset Map for the
selected weather products (optional)
TRAFFIC Cycles through traffic display options:
TRFC-1: Traffic displayed on inset map
TRFC-2: Traffic Map Page is displayed in the inset
map window. (optional feature)
Displays topographical data (e.g., coastlines, terrain,
TOPO
rivers, lakes) and elevation scale on Inset Map
Hazard
Avoidance
Procedures
Flight
Planning
GPS Nav
Nav/Com/
XPDR/Audio
EIS
Flight
Instruments
Appendix
TERRAIN
Displays terrain information on Inset Map
NEXRAD
Displays NEXRAD weather and coverage
information on Inset Map (optional feature)
Displays SiriusXM lightning information on Inset
Map (optional feature)
Displays METAR flags on airport symbols shown on
the Inset Map (optional)
Additional
Features
XM LTNG
Index
Appendix
Annun/Alerts
Abnormal
Operation
METAR
102
Garmin G1000 Cockpit Reference Guide for the Piper PA-44-180 Seminole
190-01462-00 Rev. A
Appendix
Flight
Instruments
DME
SYN VIS
ALT UNIT
HSI FMT
EIS
Select the BACK Softkey
to return to the top-level softkeys
Nav/Com/
XPDR/Audio
METERS
GPS Nav
360 HSI
BACK
ARC HSI
IN
HPA
Flight
Planning
Procedures
PATHWAY
SYN TERR HRZN HDG APTSIGNS
Level 1
Level 2
Hazard
Avoidance
PFD Configuration Softkeys
SYN VIS
SYN TERR
Appendix
HRZN HDG Displays compass heading along the
Zero-Pitch line
Annun/Alerts
PATHWAY
Displays second-level softkeys for
additional PFD configurations
Displays the softkeys for enabling or
disabling Synthetic Vision features
Displays rectangular boxes
representing the horizontal and
vertical flight path of the active flight
plan
Enables synthetic terrain depiction
PFD
Abnormal
Operation
Description
Additional
Features
Level 3
Index
190-01462-00 Rev. A
Garmin G1000 Cockpit Reference Guide for the Piper PA-44-180 Seminole
103
Level 1
Level 2
Level 3
Description
APTSIGNS
Displays position markers for
airports within approximately
15 nm of the current aircraft
position. Airport identifiers are
displayed when the airport is within
approximately 9 nm.
Resets PFD to default settings,
including changing units to standard
Displays softkeys to select wind data
parameters
Wind direction arrows with
headwind and crosswind components
Wind direction arrow and speed
Nav/Com/
XPDR/Audio
EIS
Flight
Instruments
Appendix
GPS Nav
DFLTS
WIND
Flight
Planning
OPTN 1
OPTN 2
Procedures
OPTN 3
Hazard
Avoidance
OFF
Press to display the DME
information window
Cycles the Bearing 1 Information
Window through NAV1 or GPS/
waypoint identifier and GPS-derived
distance information.
Displays the HSI formatting softkeys
Additional
Features
DME
Abnormal
Operation
BRG1
HSI FRMT
Annun/Alerts
360 HSI
ARC HSI
Index
Appendix
BRG2
ALT UNIT
104
Wind direction arrow with
headwind/tailwind and crosswind
components
Information not displayed
Displays the HSI in a 360 degree
format
Displays the HSI in an arc format
Cycles the Bearing 2 Information
Window through NAV2 or GPS/
waypoint identifier and GPS-derived
distance information.
Displays softkeys for setting the
altimeter and BARO settings to
metric units
Garmin G1000 Cockpit Reference Guide for the Piper PA-44-180 Seminole
190-01462-00 Rev. A
Appendix
Level 2
Level 3
METERS
STD BARO
Flight
Planning
Hazard
Avoidance
Select the BACK Softkey to return
to the top-level softkeys.
Additional
Features
Transponder Softkeys
Level 3
Description
STBY
ALT
Garmin G1000 Cockpit Reference Guide for the Piper PA-44-180 Seminole
105
Index
190-01462-00 Rev. A
Appendix
GND
Annun/Alerts
ON
Selects Standby Mode (transponder does
not reply to any interrogations)
Selects Mode A (transponder replies to
interrogations)
Selects Mode C – Altitude Reporting Mode
(transponder replies to identification and
altitude interrogations)
Manually selects Ground Mode, the
transponder does not allow Mode A
and Mode C replies, but it does permit
acquisition squitter and replies to discretely
addressed Mode S interrogations.
Abnormal
Operation
Displays transponder mode selection softkeys
XPDR
Procedures
Select the BACK Softkey to return
to the top-level softkeys.
Level 2
GPS Nav
ADS-B TX
Level 1
Nav/Com/
XPDR/Audio
HPA
When enabled, displays altimeter in
meters
Press to display the BARO setting as
inches of mercury
Press to display the BARO setting as
hectopacals
Sets barometric pressure to 29.92 in
Hg (1013 hPa)
EIS
IN
Description
Flight
Instruments
Level 1
Level 1
Level 2
Level 3
Description
0—7
Automatically enters the VFR code (1200 in
the U.S.A. only)
Displays transponder code selection
softkeys 0-7
Use numbers to enter code
BKSP
Removes numbers entered, one at a time
VFR
CODE
Nav/Com/
XPDR/Audio
EIS
Flight
Instruments
Appendix
TMR/REF
Activates/deactivates transmission of the
aircraft’s three-dimensional position and
aircraft heading for reception by ADS-B
systems.
Activates the Special Position Identification
(SPI) pulse for 18 seconds, identifying the
transponder return on the ATC screen
Displays Timer/References Window
NRST
Displays Nearest Airports Window
MSG
Displays Message Window
Hazard
Avoidance
Procedures
Flight
Planning
GPS Nav
ADS-B TX
IDENT
MFD SOFTKEY MAP
ENGINE
DCLTR
Additional
Features
MAP
SHW CHRT
(optional)
DCLTR-1
Press the ENGINE Softkey to return
to the previous softkey level.
Abnormal
Operation
ENGINE
DEC FUEL
DCLTR-2
INC FUEL
RST FUEL
Annun/Alerts
DCLTR-3
(Default softkey
is dependant on
the selection made
in the map setup
options)
(optional)
TRAFFIC
PROFILE
TOPO
TERRAIN
AIRWAYS
Press the BACK Softkey on this
level to return to the top softkey level.
(optional)
(optional)
NEXRAD
XM LTNG
METAR
LEGEND
BACK
AIRWY ON
Appendix
AIRWY LO
AIRWAY HI
Index
MFD Softkeys
106
Garmin G1000 Cockpit Reference Guide for the Piper PA-44-180 Seminole
190-01462-00 Rev. A
Appendix
Level 2
ENGINE
Abnormal
Operation
TERRAIN
Additional
Features
TOPO
Hazard
Avoidance
PROFILE
Procedures
TRAFFIC
Flight
Planning
MAP
Annun/Alerts
Displays the default engine
softkey level. Press again
to return to the previous
softkey level
Press to decrease fuel
quantity in 1-gallon
increments
Press to increase fuel
quantity in 1-gallon
increments
Resets remaining fuel to
zero
Enables second-level
Navigation Map softkeys
Displays traffic information
on Navigation Map
(optional)
Displays/removes Profile
View on Navigation Map
Page
Displays topographical data
(e.g., coastlines, terrain,
rivers, lakes) and elevation
scale on Navigation Map
Displays terrain
information on Navigation
Map
GPS Nav
RST FUEL
Description
Nav/Com/
XPDR/Audio
INC FUEL
Level 4
EIS
DEC FUEL
Level 3
Flight
Instruments
Level 1
Appendix
Index
190-01462-00 Rev. A
Garmin G1000 Cockpit Reference Guide for the Piper PA-44-180 Seminole
107
Level 1
Level 2
AIRWAYS
Flight
Planning
GPS Nav
Nav/Com/
XPDR/Audio
EIS
Flight
Instruments
Appendix
Procedures
NEXRAD
Abnormal
Operation
Additional
Features
Hazard
Avoidance
XM LTNG
Annun/Alerts
METAR
Index
Appendix
LEGEND
BACK
108
Level 3
Level 4
Description
Displays airways on the
map; cycles through the
following:
AIRWAYS: No airways
are displayed
AIRWY ON: All airways
are displayed
AIRWY LO: Only low
altitude airways are
displayed
AIRWY HI: Only high
altitude airways are
displayed
Displays NEXRAD weather
and coverage information
on the Navigation Map
(optional)
Displays XM lightning
information on Navigation
Map (optional feature). XM
lightning and Stormscope
lightning are mutually
exclusive when displaying
on the Navigation Map.
Displays METAR flags on
airport symbols shown
on the Navigation Map
(optional)
Displays the legend for
the selected weather
products. Available only
when NEXRAD, XM LTNG,
PROFILE and/or METAR
softkeys are selected.
Returns to top-level softkeys
Garmin G1000 Cockpit Reference Guide for the Piper PA-44-180 Seminole
190-01462-00 Rev. A
Appendix
Level 2
Level 3
Level 4
Description
Annun/Alerts
Appendix
Index
109
Abnormal
Operation
Garmin G1000 Cockpit Reference Guide for the Piper PA-44-180 Seminole
Additional
Features
190-01462-00 Rev. A
Hazard
Avoidance
In some cases it may be necessary to obtain an unlock code from Garmin in order
to make the database product functional. It may also be necessary to have the system
configured by a Garmin authorized service facility in order to use some database features.
If an error occurs during synchronization, an error message will be displayed,
followed by the affected display in the Sync Status section of the Database Window.
If synchronization completes on one display, but an error occurs on another, the error
message will be displayed with the affected displays listed after it. When an error
message is displayed, the problem must be corrected before synchronization can be
completed. A power cycle is required to restart synchronization when ‘Card Full’ or
‘Err’ is shown.
Procedures
NOTE: When loading database updates, the ‘DB Mismatch’ message will
be displayed until database synchronization is complete, followed by turning
system power off, then on. Synchronization can be monitored on the AUXSYSTEM STATUS Page.
Flight
Planning
CAUTION: Never disconnect power to the system when loading a database.
Power interruption during the database loading process could result in maintenance being required to reboot the system.
GPS Nav
LOADING UPDATED DATABASES
Nav/Com/
XPDR/Audio
SHW CHRT
EIS
Selects desired amount of
map detail; cycles through
declutter levels:
DCLTR (No Declutter):
All map features visible
DCLTR-1: Declutters land
data
DCLTR-2: Declutters land
and SUA data
DCLTR-3: Removes
everything except the
active flight plan
When available, displays
optional airport and
terminal procedure charts
DCLTR (3)
Flight
Instruments
Level 1
Error Message
Description
Canceled
Database synchronization has been canceled by removing the
bottom SD card in display being updated
Card Full
SD card does not contain sufficient memory
Err
Displayed for all other errors that may cause the synchronization
process to be halted
Timeout
System timed-out prior to the database transfer completing
Updating Basemap, SafeTaxi, Airport Terrain, Obstacle, and Airport
Directory Databases
These databases may be copied to one Supplemental Data Card, then automatically
synchronized to other card in the system:
Appendix
Annun/Alerts
Abnormal
Operation
Additional
Features
Hazard
Avoidance
Procedures
Flight
Planning
GPS Nav
Nav/Com/
XPDR/Audio
EIS
Flight
Instruments
Appendix
1)
With system power OFF, remove the MFD database card from the bottom
card slot of the MFD.
2)
Update the basemap, SafeTaxi, airport terrain, obstacle and/or airport
directory databases on the MFD card.
3)
Insert the MFD database card into the bottom card slot of the MFD.
4)
Apply power to the system, check that the databases are initialized and
displayed on the power-up screen. If a ‘Verifying’ message is seen, wait for
the system to finish loading before proceeding to step 5.
5)
Acknowledge the Power-up Page agreement by pressing the ENT Key or
the right most softkey.
6)
Turn the large FMS Knob to select the AUX Page group on the MFD.
7)
Turn the small FMS Knob to select the System Status Page.
8)
Monitor the Sync Status in the Database Window. Wait for all databases to
complete synching, indicated by ‘Complete’ being displayed.
9)
Remove and reapply power to the system.
10) Turn the large FMS Knob to select the AUX Page group on the MFD.
11) Turn the small FMS Knob to select the System Status Page.
Index
12) Press the Display Database Selection Softkey to show database information
for each display (MFD1 DB or PFD1 DB). Verify the correct database cycle
information is shown for each database for each display.
110
Garmin G1000 Cockpit Reference Guide for the Piper PA-44-180 Seminole
190-01462-00 Rev. A
Appendix
Flight
Instruments
Updating Terrain, FliteCharts, and ChartView Databases
These databases must be copied to both Supplemental Data Cards:
With system power OFF, remove the Supplemental Data Card from the
bottom card slot of the MFD and PFD.
2)
Update the terrain and/or FliteCharts or ChartView databases on each of
the Supplemental Data Cards.
3)
Insert the updated Supplemental Data Cards into the bottom card slot of
the MFD and PFD.
4)
Apply power to the system, check that the databases are initialized and
displayed on the power-up screen. A ‘Verifying’ message may be seen.
If this message is present, wait for the system to finish loading before
proceeding to step 5.
5)
Acknowledge the Power-up Page agreement by pressing the ENT Key or
the right most softkey.
6)
Turn the large FMS Knob to select the AUX Page group on the MFD.
7)
Turn the small FMS Knob to select the System Status Page.
8)
Press the Display Database Selection Softkey to show database information
for each display (MFD1 DB or PFD1 DB). Verify the correct database cycle
information is shown for each database for each display.
9)
Remove power from the system.
EIS
1)
Nav/Com/
XPDR/Audio
GPS Nav
Flight
Planning
Procedures
Hazard
Avoidance
Additional
Features
Abnormal
Operation
Annun/Alerts
Appendix
Index
190-01462-00 Rev. A
Garmin G1000 Cockpit Reference Guide for the Piper PA-44-180 Seminole
111
Loading the Jeppesen Navigation Database as the Active Navigation
Database
The Jeppesen Navigation Database that is loaded to internal memory as the active
database will be used by the system.
NOTE: Loading the Jeppesen Navigation Database as the active database
prior to its effective date will result in the expiration date on the power-up
screen and the effective date on the AUX-System Status Page being displayed
in yellow.
GPS Nav
Nav/Com/
XPDR/Audio
EIS
Flight
Instruments
Appendix
Flight
Planning
With the system OFF, insert the SD card containing the new navigation database
version into the top card slot of the display (PFD or MFD) to be updated (label
of SD card facing left).
2)
Turn the system ON. A prompt is displayed in the upper left corner of the
display:
3)
4)
Press the NO Softkey to proceed to loading the active database.
A prompt similar to the following is displayed. Press the YES Softkey to update
the active navigation database.
Index
Appendix
Annun/Alerts
Abnormal
Operation
Additional
Features
Hazard
Avoidance
1)
Procedures
NOTE: After the navigation database is loaded or copied, the top SD card
may be removed.
112
Garmin G1000 Cockpit Reference Guide for the Piper PA-44-180 Seminole
190-01462-00 Rev. A
Appendix
After the update completes, the display starts in normal mode.
6)
Turn the system OFF and remove the SD card from the top card slot.
7)
Repeat steps 1 through 6 for the other display (PFD or MFD).
8)
Apply power to the system and press the ENT Key to acknowledge the startup
screen.
9)
Turn the large FMS Knob to select the AUX Page group on the MFD.
Flight
Instruments
5)
Flight
Planning
Procedures
The purpose of the Standby Navigation Database is to allow the loading of the
next cycle of the Jeppesen Navigation Database to the bottom SD card, prior to its
effective date. (The Jeppesen Navigation Database is available from Jeppesen seven
days prior to its effective date.)
GPS Nav
Loading the Jeppesen Navigation Database as the Standby Navigation
Database
Nav/Com/
XPDR/Audio
11) Press the Display Database Selection Softkey to show active navigation
database information for each display (MFD1 DB, PFD1 DB). Verify the
correct active navigation database cycle information is shown for each display.
EIS
10) Turn the small FMS Knob to select the System Status Page.
Hazard
Avoidance
NOTE: After the navigation database is loaded or copied, the top SD card
may be removed.
Additional
Features
With the system OFF, insert the SD card containing the new navigation
database version into the top card slot of the MFD.
2)
Verify that an SD card is inserted in the bottom slot of the PFD and the
MFD.
3)
Turn the system ON. A prompt is displayed.
4)
Press the YES Softkey. The navigation database is copied to the SD card in
the bottom card slot of the MFD.
Abnormal
Operation
1)
Annun/Alerts
Appendix
Index
190-01462-00 Rev. A
Garmin G1000 Cockpit Reference Guide for the Piper PA-44-180 Seminole
113
5)
After the navigation database files are copied to the bottom SD card, press
any key to verify, as instructed.
6)
After database verification is complete, press any key to continue as
instructed on the display.
7)
Press the NO Softkey. The display now starts in normal mode. Since the
database effective date is not yet valid, it should not be loaded as the
active database. The display now starts in normal mode. Do not remove
power while the display is starting.
8)
Press the ENT Key to acknowledge the startup screen.
9)
Turn the large FMS Knob to select the AUX Page group on the MFD.
GPS Nav
Nav/Com/
XPDR/Audio
EIS
Flight
Instruments
Appendix
10) Turn the small FMS Knob to select the System Status Page.
Procedures
Flight
Planning
11) The new database is copied to the SD card in the bottom card slot of the
PFD. Progress can be monitored in the SYNC STATUS field. When copying
is finished, ‘Complete’ is displayed.
Hazard
Avoidance
NOTE: During the synchronization process, version differences between
standby navigation databases will exist. This will result in the system
displaying a ‘DB Mismatch’ alert for the standby navigation databases. This
alert will remain until the next power cycle.
Additional
Features
12) Turn system power OFF.
13) Remove the SD card from the top card slot of the MFD.
14) Turn system power ON.
Abnormal
Operation
15) Press the ENT Key to acknowledge the startup screen.
16) Turn the large FMS Knob to select the AUX Page group on the MFD.
Annun/Alerts
17) Turn the small FMS Knob to select the System Status Page.
Index
Appendix
18) Press the Display Database Selection Softkey to show standby navigation
database information for each display (MFD1 DB, PFD1 DB). Verify the
correct standby navigation database cycle information is shown for each
display.
114
Garmin G1000 Cockpit Reference Guide for the Piper PA-44-180 Seminole
190-01462-00 Rev. A
Appendix
EIS
At startup, the system compares this version of the MV DB with that presently being
used by the AHRS (GRS). If the system determines the MV DB needs to be updated,
a prompt is displayed on the Navigation Map Page, as shown in the following figure.
Flight
Instruments
Magnetic Field Variation Database Update
Nav/Com/
XPDR/Audio
GPS Nav
GRS Magnetic Field Variation Database Update Prompt
Flight
Planning
Procedures
Loading the magnetic field variation database update:
With ‘OK’ highlighted, as shown in the previous figure, press the ENT Key
on the MFD. A progress monitor is displayed as shown in the following
figure.
Hazard
Avoidance
Additional
Features
Abnormal
Operation
Uploading Database to GRS
Annun/Alerts
Appendix
Index
190-01462-00 Rev. A
Garmin G1000 Cockpit Reference Guide for the Piper PA-44-180 Seminole
115
Index
Appendix
Annun/Alerts
Abnormal
Operation
Additional
Features
Hazard
Avoidance
Procedures
Flight
Planning
GPS Nav
Nav/Com/
XPDR/Audio
EIS
Flight
Instruments
Appendix
Blank Page
116
Garmin G1000 Cockpit Reference Guide for the Piper PA-44-180 Seminole
190-01462-00 Rev. A
Index
Horizon heading 57
Abnormal
Operation
I
Inhibit 54, 56
Inhibit TAWS 56
Inhibit Terrain 54
Insertion Point Indicator 31
Inset Map 101, 102
IOI 77, 78, 79, 80
Annun/Alerts
Appendix
J
Index
190-01462-00 Rev. A
H
Jeppesen 59
Garmin G1000 Cockpit Reference Guide for the Piper PA-44-180 Seminole
Additional
Features
Data Link Receiver 81
DB Mismatch 109, 114
DCLTR Softkey 58
Flight ID 50
Flight path marker 57
Flight plan import/export messages 97
FliteCharts® 58, 59
Frequency Transfer 12
Fuel
Calculations 9
Quantity 6
Hazard
Avoidance
D
F
Procedures
Caution alerts 76
CDI 1, 11, 95
Channel Presets 62
ChartView 58, 59
Clearance player 12
Clearance recorder 12
Code selection softkeys 11
COM 11, 12, 69
Edit a flight plan 35
Enable Terrain 54
Endurance, calculated (ENDUR) 8, 9
Engine manifold pressure 6, 7
Flight
Planning
C
E
GPS Nav
Barometric Altitude Minimums 2
Barometric pressure 105
Nav/Com/
XPDR/Audio
B
Dead Reckoning 70
DEC FUEL softkey 9
Declutter 70, 102, 109
Designated altitudes 18, 19
Direct-to 15
DME 11
DR mode 70, 71, 72
EIS
Activate a flight plan 16
Active Channel 61
Active database 112
Active Navigation Database 112
AC-U-KWIK 60
ADF 11
ADS-B 48, 106
AHRS 73, 91, 92
Airport Directory 60
Airport Signs 57, 58
Airways 108
Altimeter setting 1, 70
AOPA 60
AOPA’s Airport Directory 60
Approach channel 41
Audio panel controls
NAV1, NAV2 11
Flight
Instruments
A
Index-1
Index
Appendix
Annun/Alerts
Abnormal
Operation
Additional
Features
Hazard
Avoidance
Procedures
Flight
Planning
GPS Nav
Nav/Com/
XPDR/Audio
EIS
Flight
Instruments
Index
M
Map panning 46
Message advisories 82, 83, 86, 87, 90,
91, 92, 93
METAR 45
MKR/MUTE 12
Mode S 105
Mode selection softkeys 11
Multi Function Display (MFD)
Softkeys 106
N
NAV 11, 12
NAV1 1, 11
NAV2 1, 11
Navigation database 17, 19
NEXRAD 45, 102, 108
O
OBS 2
Obstacles 85, 86, 87
P
Standby Navigation Database 113
Store Flight Plan 34
SVT 57, 96
Synchronization 110
SYNC Status 114
Synthetic Vision System 57
T
Tachometer 6, 7
TAF 45
TAS 91
TAWS 55, 56, 79
TAWS-B 55
Terrain 52, 53, 55, 85, 102, 107
Terrain-SVS 53, 54
Timer 2, 93
Topographical data 102, 107
Traffic 45, 49, 107
Traffic Advisory 49
Traffic map page 49, 50, 51, 52
Transponder 11, 105, 106
V
Pathways 57, 58
Pilot Profile 64
Profile View 107
vertical path guidance 18
Vertical speed guidance 19
VNV 15, 70, 95
Voice alerts 75
R
W
Reversionary mode 69
ROC 77, 79
Warning alerts 75
Waypoint Selection Submenu 28, 29
Weather data link page 46
Wind data 104
S
SafeTaxi® 58
SBAS 40, 54, 56, 71, 87, 89
Scheduler 63
SiriusXM lightning 102, 108
SiriusXM Weather 46
Index-2
Garmin G1000 Cockpit Reference Guide for the Piper PA-44-180 Seminole
190-01462-00 Rev. A
Garmin International, Inc.
1200 East 151st Street
Olathe, KS 66062, U.S.A.
p: 913.397.8200 f: 913.397.8282
Garmin AT, Inc.
2345 Turner Road SE
Salem, OR 97302, U.S.A.
p: 503.391.3411 f: 503.364.2138
Garmin (Europe) Ltd
Liberty House, Bulls Copse Road
Hounsdown Business Park
Southampton, SO40 9RB, U.K.
p: 44/0870.8501241 f: 44/0870.8501251
Garmin Corporation
No. 68, Jangshu 2nd Road
Shijr, Taipei County, Taiwan
p: 886/2.2642.9199 f: 886/2.2642.9099
www.garmin.com
© 2013 Garmin Ltd. or its subsidiaries
190-01462-00 Rev. A
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising