Garmin | G1000: Socata TBM 700 | Garmin G1000: Socata TBM 700 G1000 Cockpit Reference Guide for the Socata TBM 700

Garmin G1000: Socata TBM 700 G1000 Cockpit Reference Guide for the Socata TBM 700
G1000
®
Integrated Flight Deck
Cockpit Reference Guide
FLIGHT INSTRUMENTS
ENGINE & AIRFRAME SYSTEMS
NAV/COM/TRANSPONDER/AUDIO PANEL
AUTOMATIC FLIGHT CONTROL SYSTEM
GPS NAVIGATION
FLIGHT PLANNING
PROCEDURES
HAZARD AVOIDANCE
ADDITIONAL FEATURES
ABNORMAL OPERATION
ANNUNCIATIONS & ALERTS
APPENDIX
INDEX
Copyright © 2010, 2014, 2015 Garmin Ltd. or its subsidiaries. All rights reserved.
This manual reflects the operation of System Software version 0829.01 or later for the Socata
TBM 700 A, B, C, and N. Some differences in operation may be observed when comparing the
information in this manual to earlier or later software versions.
Garmin International, Inc., 1200 East 151st Street, Olathe, Kansas 66062, U.S.A.
Tel: 913/397.8200Fax: 913/397.8282
Garmin AT, Inc., 2345 Turner Road SE, Salem, OR 97302, U.S.A.
Tel: 503/391.3411Fax 503/364.2138
Garmin (Europe) Ltd, Liberty House, Hounsdown Business Park, Southampton, SO40 9LR, U.K.
Tel: 44 (0) 23 8052 4000Fax: 44 (0) 23 8052 4004
Garmin Corporation, No. 68, Jangshu 2nd Road, Shijr, Taipei County, Taiwan
Tel: 886/02.2642.9199
Fax: 886/02.2642.9099
For after-hours emergency, aircraft on ground (AOG) technical support for Garmin panel mount
and integrated avionics systems, please contact Garmin’s AOG Hotline at 913.397.0836.
Web Site Address: www.garmin.com
Except as expressly provided herein, no part of this manual may be reproduced, copied,
transmitted, disseminated, downloaded or stored in any storage medium, for any purpose
without the express written permission of Garmin. Garmin hereby grants permission to
download a single copy of this manual and of any revision to this manual onto a hard drive or
other electronic storage medium to be viewed for personal use, provided that such electronic
or printed copy of this manual or revision must contain the complete text of this copyright
notice and provided further that any unauthorized commercial distribution of this manual or any
revision hereto is strictly prohibited.
Garmin® and G1000® are registered trademarks of Garmin Ltd. or its subsidiaries. WATCH®,
FliteCharts®, and SafeTaxi® are trademarks of Garmin Ltd. or its subsidiaries. These trademarks
may not be used without the express permission of Garmin.
NavData® is a registered trademark of Jeppesen, Inc.; Stormscope® is a registered trademark of
L-3 Communications; and SiriusXM® is a registered trademark of SiriusXM Satellite Radio, Inc.
AOPA Membership Publications, Inc. and its related organizations (hereinafter collectively
“AOPA”) expressly disclaim all warranties, with respect to the AOPA information included in this
data, express or implied, including, but not limited to, the implied warranties of merchantability
and fitness for a particular purpose. The information is provided “as is” and AOPA does not
warrant or make any representations regarding its accuracy, reliability, or otherwise. Under
no circumstances including negligence, shall AOPA be liable for any incidental, special or
consequential damages that result from the use or inability to use the software or related
documentation, even if AOPA or an AOPA authorized representative has been advised of the
possibility of such damages. User agrees not to sue AOPA and, to the maximum extent allowed
by law, to release and hold harmless AOPA from any causes of action, claims or losses related
to any actual or alleged inaccuracies in the information. Some jurisdictions do not allow the
limitation or exclusion of implied warranties or liability for incidental or consequential damages
so the above limitations or exclusions may not apply to you.
May, 2015
190-01247-01 Rev. A
Printed in the U.S.A.
Warnings, Cautions & Notes
WARNING: Navigation and terrain separation must NOT be predicated upon
the use of the terrain avoidance feature. The terrain avoidance feature is NOT
intended to be used as a primary reference for terrain avoidance and does
not relieve the pilot from the responsibility of being aware of surroundings
during flight. The terrain avoidance feature is only to be used as an aid for
terrain avoidance. Terrain data is obtained from third party sources. Garmin
is not able to independently verify the accuracy of the terrain data.
WARNING: The displayed minimum safe altitudes (MSAs) are only advisory
in nature and should not be relied upon as the sole source of obstacle and
terrain avoidance information. Always refer to current aeronautical charts
for appropriate minimum clearance altitudes.
WARNING: The altitude calculated by G1000 GPS receivers is geometric
height above Mean Sea Level and could vary significantly from the altitude
displayed by pressure altimeters, such as the GDC 74B Air Data Computer,
or other altimeters in the aircraft. GPS altitude should never be used for
vertical navigation. Always use pressure altitude displayed by the G1000
PFD or other pressure altimeters in aircraft.
WARNING: Do not use outdated database information. Databases used in
the G1000 system must be updated regularly in order to ensure that the
information remains current. Pilots using any outdated database do so
entirely at their own risk.
WARNING: Do not use basemap (land and water data) information for
primary navigation. Basemap data is intended only to supplement other
approved navigation data sources and should be considered as an aid to
enhance situational awareness.
WARNING: Traffic information shown on system displays is provided as an
aid in visually acquiring traffic. Pilots must maneuver the aircraft based only
upon ATC guidance or positive visual acquisition of conflicting traffic.
WARNING: Use of the Stormscope is not intended for hazardous weather
penetration (thunderstorm penetration). Stormscope information, as
displayed on the G1000 MFD, is to be used only for weather avoidance, not
penetration.
190-01247-01 Rev. A
Garmin G1000 Cockpit Reference Guide for the Socata TBM 700
Warnings, Cautions & Notes
WARNING: Do not use datalink weather products (e.g., SiriusXM WX
Satellite Weather, GFDS World Wide Weather, or FIS-B) for hazardous weather
penetration. Weather information provided by these products is aged by up
to several minutes and may not depict actual weather conditions as they
currently appear.
WARNING: NEXRAD weather data is to be used for long-range planning
purposes only. Due to inherent delays in data transmission and the relative
age of the data, NEXRAD weather data should not be used for short-range
weather avoidance.
WARNING: The Garmin G1000, as installed in the Socata TBM 700 aircraft, has
a very high degree of functional integrity. However, the pilot must recognize
that providing monitoring and/or self-test capability for all conceivable system
failures is not practical. Although unlikely, it may be possible for erroneous
operation to occur without a fault indication shown by the G1000. It is
thus the responsibility of the pilot to detect such an occurrence by means of
cross-checking with all redundant or correlated information available in the
cockpit.
WARNING: For safety reasons, G1000 operational procedures must be learned
on the ground.
WARNING: The United States government operates the Global Positioning
System and is solely responsible for its accuracy and maintenance. The GPS
system is subject to changes which could affect the accuracy and performance
of all GPS equipment. Portions of the Garmin G1000 utilize GPS as a
precision electronic NAVigation AID (NAVAID). Therefore, as with all NAVAIDs,
information presented by the G1000 can be misused or misinterpreted and,
therefore, become unsafe.
WARNING: To reduce the risk of unsafe operation, carefully review and
understand all aspects of the G1000 Pilot’s Guide documentation and the
Socata TBM 700 Airplane Flight Manual. Thoroughly practice basic operation
prior to actual use. During flight operations, carefully compare indications
from the G1000 to all available navigation sources, including the information
from other NAVAIDs, visual sightings, charts, etc. For safety purposes, always
resolve any discrepancies before continuing navigation.
Garmin G1000 Cockpit Reference Guide for the Socata TBM 700
190-01247-01 Rev. A
Warnings, Cautions & Notes
WARNING: The illustrations in this guide are only examples. Never use
the G1000 to attempt to penetrate a thunderstorm. Both the FAA Advisory
Circular, Subject: Thunderstorms, and the Aeronautical Information Manual
(AIM) recommend avoiding “by at least 20 miles any thunderstorm identified
as severe or giving an intense radar echo.”
WARNING: Lamp(s) inside this product may contain mercury (HG) and must
be recycled or disposed of according to local, state, or federal laws. For
more information, refer to our website at www.garmin.com/aboutGarmin/
environment/disposal.jsp.
WARNING: Because of variation in the earth’s magnetic field, operating the
system within the following areas could result in loss of reliable attitude and
heading indications. North of 72° North latitude at all longitudes. South of
70° South latitude at all longitudes. North of 65° North latitude between
longitude 75° W and 120° W. (Northern Canada). North of 70° North latitude
between longitude 70° W and 128° W. (Northern Canada). North of 70° North
latitude between longitude 85° E and 114° E. (Northern Russia). South of
55° South latitude between longitude 120° E and 165° E. (Region south of
Australia and New Zealand).
WARNING: Do not use GPS to navigate to any active waypoint identified as
a ‘NON WGS84 WPT’ by a system message. ‘NON WGS84 WPT’ waypoints are
derived from an unknown map reference datum that may be incompatible
with the map reference datum used by GPS (known as WGS84) and may be
positioned in error as displayed.
WARNING: Do not use a QFE altimeter setting with this system. System
functions will not operate properly with a QFE altimeter setting. Use only
a QNH altimeter setting for height above mean sea level, or the standard
pressure setting, as applicable.
CAUTION: The PFD and MFD displays use a lens coated with a special
anti-reflective coating that is very sensitive to skin oils, waxes, and abrasive
cleaners. CLEANERS CONTAINING AMMONIA WILL HARM THE ANTIREFLECTIVE COATING. It is very important to clean the lens using a clean,
lint-free cloth and an eyeglass lens cleaner that is specified as safe for antireflective coatings.
190-01247-01 Rev. A
Garmin G1000 Cockpit Reference Guide for the Socata TBM 700
Warnings, Cautions & Notes
CAUTION: The Garmin G1000 does not contain any user-serviceable parts.
Repairs should only be made by an authorized Garmin service center.
Unauthorized repairs or modifications could void both the warranty and the
pilot’s authority to operate this device under FAA/FCC regulations.
NOTE: All visual depictions contained within this document, including screen
images of the G1000 panel and displays, are subject to change and may not
reflect the most current G1000 system and aviation databases. Depictions
of equipment may differ slightly from the actual equipment.
NOTE: This device complies with part 15 of the FCC Rules. Operation is
subject to the following two conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
NOTE: The data contained in the terrain and obstacle databases comes from
government agencies. Garmin accurately processes and cross-validates the
data, but cannot guarantee the accuracy and completeness of the data.
NOTE: This product, its packaging, and its components contain chemicals
known to the State of California to cause cancer, birth defects, or reproductive
harm. This notice is being provided in accordance with California’s Proposition
65. If you have any questions or would like additional information, please
refer to our web site at www.garmin.com/prop65.
NOTE: Interference from GPS repeaters operating inside nearby hangars can
cause an intermittent loss of attitude and heading displays while the aircraft
is on the ground. Moving the aircraft more than 100 yards away from the
source of the interference should alleviate the condition.
NOTE: Use of polarized eyewear may cause the flight displays to appear dim
or blank.
NOTE: The purpose of this Cockpit Reference Guide is to provide the pilot
a resource with which to find operating instructions on the major features
of the G1000 system more easily. It is not intended to be a comprehensive
operating guide. Complete operating procedures for the system are found
in the G1000 Pilot’s Guide for this aircraft.
Garmin G1000 Cockpit Reference Guide for the Socata TBM 700
190-01247-01 Rev. A
Warnings, Cautions & Notes
NOTE: The FAA has asked Garmin to remind pilots who fly with Garmin
database-dependent avionics of the following:
• It is the pilot’s responsibility to remain familiar with all FAA regulatory
and advisory guidance and information related to the use of databases in
the National Airspace System.
• Garmin equipment will only recognize and use databases that are
obtained from Garmin or Jeppesen. Databases obtained from Garmin
or Jeppesen are assured compliance with all data quality requirements
(DQRs) by virtue of a Type 2 Letter of Authorization (LOA) from the FAA. A
copy of the Type 2 LOA is available for each database and can be viewed
at http://fly.garmin.com by selecting ‘Type 2 LOA Status.’
• Use of a current Garmin or Jeppesen database in your Garmin equipment
is required for compliance with established FAA regulatory guidance, but
does not constitute authorization to fly any and all terminal procedures
that may be presented by the system. It is the pilot’s responsibility to
operate in accordance with established AFM(S) and regulatory guidance or
limitations as applicable to the pilot, the aircraft, and installed equipment.
NOTE: The pilot/operator must review and be familiar with Garmin’s database
exclusion list as discussed in SAIB CE-14-04 to determine what data may be
incomplete. The database exclusion list can be viewed at www.flygarmin.
com by selecting ‘Database Exclusions List.’
NOTE: The pilot/operator must have access to Garmin and Jeppesen database alerts and consider their impact on the intended aircraft operation. The
database alerts can be viewed at www.flygarmin.com by selecting ‘Aviation
Database Alerts.’
NOTE: If the pilot/operator wants or needs to adjust the database, contact
Garmin Product Support to coordinate the revised DQRs.
NOTE: Garmin requests the flight crew report any observed discrepancies
related to database information. These discrepancies could come in the form
of an incorrect procedure; incorrectly identified terrain, obstacles and fixes;
or any other displayed item used for navigation or communication in the air
or on the ground. Go to FlyGarmin.com and select ‘Report An Aviation Data
Error Report.’
190-01247-01 Rev. A
Garmin G1000 Cockpit Reference Guide for the Socata TBM 700
Warnings, Cautions & Notes
Blank Page
Garmin G1000 Cockpit Reference Guide for the Socata TBM 700
190-01247-01 Rev. A
Record of Revisions
Part Number
190-01247-00
190-01247-01
Change Summary
Initial Release
Added CPDLC
Added GWX 70
Updated CAS messages
Updated Engine Indications
Added Satellite Telephone and SMS Messaging Service
Added Maintenance Logs
Added Auxillary Video
Updated Loading Database information
Updated System Message Adivsories
Added Weather Radar Overlay on Navigation Map Page
Added Profile View
Added other GDU 14.02 parameters
Revision Date of Revision Affected Pages
A
May, 2015
All
190-01247-01 Rev. A
Description
Production Release
Garmin G1000 Cockpit Reference Guide for the Socata TBM 700
RR-1
Record of Revisions
Blank Page
RR-2
Garmin G1000 Cockpit Reference Guide for the Socata TBM 700
190-01247-01 Rev. A
Table of Contents
Flight Instruments........................................................................................................................ 1
Selecting the Altimeter Barometric Pressure Setting....................................................... 1
Selecting Standard Barometric Pressure.............................................................................. 1
Change Altimeter Barometric Pressure Setting Units....................................................... 1
Synchronizing the Altimeter Barometric Pressure Settings............................................ 1
Synchronize CDI......................................................................................................................... 1
Change Navigation Sources.................................................................................................... 2
Enable/Disable OBS Mode While Navigating with GPS..................................................... 2
Generic Timer.............................................................................................................................. 2
Configure Vspeed Bugs............................................................................................................. 2
Set Barometric/Radar Altimeter Minimum Descent Altitude.......................................... 3
Manually Testing the Radar Altimeter (KRA 405B only)................................................... 3
Displaying Wind Data............................................................................................................... 3
Changing HSI Format................................................................................................................ 4
Engine & Airframe Systems..................................................................................................... 5
Electrical System........................................................................................................................ 6
Fuel System............................................................................................................................... 10
General Systems...................................................................................................................... 11
Nav/Com/Transponder/Audio Panel.................................................................................. 13
Enter or Change Flight ID...................................................................................................... 13
ADF Tuning (Optional)............................................................................................................. 13
DME Tuning............................................................................................................................... 13
Enter a Transponder Code..................................................................................................... 14
Selecting a COM Radio........................................................................................................... 14
Selecting a NAV Radio............................................................................................................ 14
NAV/COM Tuning...................................................................................................................... 14
Intercom..................................................................................................................................... 15
Controller Pilot Data Link Communications (Optional).................................................. 15
Passenger Address (PA) System............................................................................................ 19
Clearance Recorder and Player............................................................................................ 19
Automatic Flight Control System...................................................................................... 21
Flight Director Activation...................................................................................................... 21
Vertical Modes.......................................................................................................................... 22
Lateral Modes........................................................................................................................... 23
GPS Navigation............................................................................................................................ 25
Direct-to Navigation............................................................................................................... 25
Activate a Stored Flight Plan................................................................................................ 26
Activate a Flight Plan Leg...................................................................................................... 26
Stop Navigating a Flight Plan............................................................................................... 27
Vertical Navigation (VNAV)................................................................................................... 27
190-01247-01 Rev. A
Garmin G1000 Cockpit Reference Guide for the Socata TBM 700
i
Table of Contents
Flight Planning............................................................................................................................. 29
Weight Planning....................................................................................................................... 29
Trip Planning............................................................................................................................. 29
Create a User Waypoint Defined by Latitude & Longitude............................................ 31
Create a User Waypoint Defined by Radials from Other Waypoints............................ 32
Create a User Waypoint Defined by a Radial & Distance from Another Waypoint... 34
Delete a User Waypoint.......................................................................................................... 35
Create a Flight Plan................................................................................................................. 36
Import a Flight Plan from an SD Card................................................................................. 37
Insert a Waypoint in the Active Flight Plan....................................................................... 37
Enter an Airway in a Flight Plan........................................................................................... 38
Invert An Active Flight Plan................................................................................................... 39
Remove a Departure, Arrival, Approach, or Airway from a Flight Plan...................... 39
Store a Flight Plan................................................................................................................... 39
Edit a Stored Flight Plan........................................................................................................ 40
Delete a Waypoint from the Flight Plan............................................................................. 40
Invert and Activate a Stored Flight Plan............................................................................ 40
Copy a Flight Plan.................................................................................................................... 41
Delete a Flight Plan................................................................................................................. 41
Graphical Flight Plan Creation.............................................................................................. 41
Export a Flight Plan to an SD Card...................................................................................... 42
Procedures...................................................................................................................................... 43
Load and Activate a Departure Procedure........................................................................ 43
Activate A Departure Leg...................................................................................................... 43
Load An Arrival Procedure..................................................................................................... 43
Activate An Arrival Leg.......................................................................................................... 44
Load and/or Activate an Approach Procedure.................................................................. 44
Activate An Approach in the Active Flight Plan................................................................ 45
Activate a Vector to Final Approach Fix............................................................................. 45
Activate A Missed Approach in the Active Flight Plan.................................................... 46
Hazard Avoidance....................................................................................................................... 47
Customizing the Hazard Displays on the Navigation Map............................................. 47
STORMSCOPE® (Optional)..................................................................................................... 47
SiriusXM Weather (Optional)................................................................................................ 49
Traffic Systems......................................................................................................................... 51
Terrain And Obstacle Proximity............................................................................................ 54
Terrain-SVS................................................................................................................................ 54
Terrain Awareness & Warning System (TAWS) Display.................................................... 56
Profile View Terrain and Obstacles...................................................................................... 58
Airborne Color Weather Radar............................................................................................. 59
ii
Garmin G1000 Cockpit Reference Guide for the Socata TBM 700
190-01247-01 Rev. A
Table of Contents
Additional Features................................................................................................................... 63
Synthetic Vision........................................................................................................................ 63
Terminal Procedure Charts.................................................................................................... 64
AOPA Airport Directory.......................................................................................................... 66
SiriusXM® Satellite Radio Entertainment.......................................................................... 67
Satellite Telephone & SMS Messaging Service................................................................. 69
Maintenance Logs.................................................................................................................... 80
Auxiliary Video (Optional)..................................................................................................... 80
Scheduler................................................................................................................................... 82
Pilot Profiles............................................................................................................................. 83
Abnormal Operation................................................................................................................. 87
Reversionary Mode................................................................................................................. 87
Abnormal COM Operation..................................................................................................... 87
Hazard Displays with Loss of GPS Position........................................................................ 87
Unusual Attitudes.................................................................................................................... 88
Dead Reckoning....................................................................................................................... 88
Annunciations & Alerts............................................................................................................ 91
CAS Messages........................................................................................................................... 91
Comparator Annunciations.................................................................................................... 93
Reversionary Sensor Annunciations.................................................................................... 93
AFCS Alerts................................................................................................................................ 94
Terrain-SVS Alerts.................................................................................................................... 95
Terrain-SVS System Status Annunciations......................................................................... 96
TAWS Alerts............................................................................................................................... 97
Voice Alerts............................................................................................................................... 99
MFD & PFD Message Advisories......................................................................................... 100
Database Message Advisories............................................................................................ 101
GMA 1347D Message Advisories........................................................................................ 104
GIA 63W Message Advisories.............................................................................................. 105
GEA 71 Message Advisories................................................................................................. 108
GTX 33/33D Message Advisories......................................................................................... 109
GRS 77 Message Advisories................................................................................................. 109
GMU 44 Message Advisories............................................................................................... 111
GDL 69A Message Advisories.............................................................................................. 112
GWX Message Advisories..................................................................................................... 112
GDC 74B Message Advisories.............................................................................................. 113
GCU 475 Message Advisories.............................................................................................. 113
GMC 710 Message Advisories............................................................................................. 114
GTS 820 Message Advisories............................................................................................... 114
GSR 56 Message Advisories................................................................................................. 114
Miscellaneous Message Advisories.................................................................................... 115
Flight Plan Import/Export Messages................................................................................. 119
190-01247-01 Rev. A
Garmin G1000 Cockpit Reference Guide for the Socata TBM 700
iii
Table of Contents
Appendix........................................................................................................................................ 121
PFD Softkey Map................................................................................................................... 121
MFD Softkey Map.................................................................................................................. 127
Updating Databases.............................................................................................................. 129
Index............................................................................................................................................Index-1
iv
Garmin G1000 Cockpit Reference Guide for the Socata TBM 700
190-01247-01 Rev. A
Flight Instruments
Flight
Instruments
FLIGHT INSTRUMENTS
SELECTING THE ALTIMETER BAROMETRIC PRESSURE SETTING
EAS
Turn the BARO Knob to select the desired setting.
Nav/Com/
XPDR/Audio
SELECTING STANDARD BAROMETRIC PRESSURE
Press the BARO Knob.
AFCS
CHANGE ALTIMETER BAROMETRIC PRESSURE SETTING UNITS
2)
Select the ALT UNIT Softkey.
3)
Select the IN Softkey to display the barometric pressure setting in inches of
mercury (in Hg).
Or:
4)
Procedures
Select the HPA Softkey to display the barometric pressure setting in
hectopascals.
Select the BACK Softkey to return to the top-level softkeys.
Hazard
Avoidance
SYNCHRONIZING THE ALTIMETER BAROMETRIC PRESSURE SETTINGS
2)
Press the FMS Knob to activate the cursor.
3)
Turn the large FMS Knob to highlight BARO in the SYNCHRONIZATION
Window.
4)
Turn the small FMS Knob clockwise to ON or counterclockwise to OFF.
Abnormal
Operation
Select the AUX-SYSTEM SETUP Page on the MFD.
Additional
Features
1)
Annun/
Alerts
SYNCHRONIZE CDI
2)
Press the FMS Knob to activate the cursor.
3)
Turn the large FMS Knob to highlight CDI in SYNCHRONIZATION Window.
4)
Turn the small FMS Knob clockwise to ON or counterclockwise to OFF.
Garmin G1000 Cockpit Reference Guide for the Socata TBM 700
Index
Select the AUX-SYSTEM SETUP Page on the MFD.
Appendix
1)
190-01247-01 Rev. A
Flight
Planning
Select the PFD Softkey to display the second-level softkeys.
GPS Nav
1)
1
CHANGE NAVIGATION SOURCES
1)
Select the CDI Softkey to change from GPS to VOR1 or LOC1. This places
the light blue tuning box over the NAV1 standby frequency in the upper left
corner of the PFD.
2)
Select the CDI Softkey again to change from VOR1 or LOC1 to VOR2
or LOC2. This places the light blue tuning box over the NAV2 standby
frequency.
3)
Select the CDI Softkey a third time to return to GPS.
ENABLE/DISABLE OBS MODE WHILE NAVIGATING WITH GPS
1)
Select the OBS Softkey to select OBS Mode.
2)
Turn a CRS Knob to select the desired course to/from the waypoint. Press
the CRS Knob to synchronize the Selected Course with the bearing to the
next waypoint.
3)
Select the OBS Softkey again to disable OBS Mode.
GENERIC TIMER
1)
Select the TMR/REF Softkey, then turn the large FMS Knob to select the
time field (hh/mm/ss). Turn the FMS Knobs to set the desired time, then
press the ENT Key. The UP/DOWN field is now highlighted.
2)
Turn the small FMS Knob to display the UP/DOWN window. Turn the FMS
Knob to select ‘UP’ or ‘DOWN’, then press the ENT Key. ‘START?’ is now
highlighted.
3)
Press the ENT Key to START, STOP, or RESET the timer (if the timer is
counting DOWN, it will start counting UP after reaching zero). Press the
CLR Key or the TMR/REF Softkey to remove the window.
CONFIGURE VSPEED BUGS
1) Select the TMR/REF Softkey.
2) Turn the large FMS Knob to highlight the desired Vspeed.
3) Use the small FMS Knob to change the Vspeed in 1-kt increments (when a
Appendix
Annun/
Alerts
Abnormal
Operation
Additional
Features
Hazard
Avoidance
Procedures
Flight
Planning
GPS Nav
AFCS
Nav/Com/
XPDR/Audio
EAS
Flight
Instruments
Flight Instruments
Index
speed has been changed from a default value, an asterisk appears next to
the speed).
2
Garmin G1000 Cockpit Reference Guide for the Socata TBM 700
190-01247-01 Rev. A
Flight Instruments
5)
Turn the small FMS Knob clockwise to ON or counterclockwise to OFF.
6)
To remove the window, press the CLR Key or the TMR/REF Softkey.
EAS
Press the ENT Key or turn the large FMS Knob to highlight the ON/OFF
field.
Flight
Instruments
4)
SET BAROMETRIC/RADAR ALTIMETER MINIMUM DESCENT ALTITUDE
Nav/Com/
XPDR/Audio
1) Press the TMR/REF Softkey.
Turn the small FMS Knob clockwise to select BARO or RAD ALT.
4)
Press the ENT Key.
5)
Use the small FMS Knob to enter the desired altitude.
6)
Press the ENT Key.
7)
To remove the window, press the CLR Key or the TMR/REF Softkey.
Flight
Planning
3)
GPS Nav
Turn the large FMS Knob to highlight the OFF/BARO/RAD ALT field to the
right of ‘MINIMUMS’.
AFCS
2)
2)
Select the RA TEST Softkey. The Radar Altitude window displays 50
feet, and ‘RA TEST’ is displayed to the left of the Radar Altitude window,
indicating a properly functioning system.
3)
Selecting the RA TEST Softkey again, or exiting the System Status Page
cancels the test.
Additional
Features
Select the AUX-SYSTEM STATUS Page on the MFD.
Hazard
Avoidance
1)
Procedures
MANUALLY TESTING THE RADAR ALTIMETER (KRA 405B ONLY)
Abnormal
Operation
DISPLAYING WIND DATA
2)
Select the WIND Softkey to display wind data below the Selected Heading.
3)
Select one of the OPTN softkeys to change how wind data is displayed.
4)
To remove the Wind Data Window, select the OFF Softkey.
Appendix
Select the PFD Softkey.
Annun/
Alerts
1)
Index
190-01247-01 Rev. A
Garmin G1000 Cockpit Reference Guide for the Socata TBM 700
3
CHANGING HSI FORMAT
EAS
Flight
Instruments
Flight Instruments
1)
Press the PFD Softkey.
2)
Press the HSI FRMT Softkey.
3)
Press the 360 HSI Softkey to display the full size HSI.
Nav/Com/
XPDR/Audio
Or:
Index
Appendix
Annun/
Alerts
Abnormal
Operation
Additional
Features
Hazard
Avoidance
Procedures
Flight
Planning
GPS Nav
AFCS
Press the ARC HSI Softkey to display the arc style HSI.
4
Garmin G1000 Cockpit Reference Guide for the Socata TBM 700
190-01247-01 Rev. A
Engine & Airframe Systems
Flight
Instruments
ENGINE & AIRFRAME SYSTEMS
EAS
1
1
8
Nav/Com/
XPDR/Audio
2
2
AFCS
9
3
3
10
5
6
6
13
15
8
9
15
10
Additional
Features
14
Hazard
Avoidance
7
Procedures
12
4
Flight
Planning
11
5
GPS Nav
4
11
Abnormal
Operation
13
14
Appendix
EIS Display (Reversionary Mode)
(Models A, B, and C)
(Model N similar)
Annun/
Alerts
EIS Display, Normal Mode
(Models A, B, and C shown)\
(Model N similar)
Index
190-01247-01 Rev. A
Garmin G1000 Cockpit Reference Guide for the Socata TBM 700
5
1
Torque
9
Differential Pressure
2
Propeller Speed
10
Fuel Quantity
3
Generator Speed
11
Fuel Flow
4
Interturbine Temperature
12
Fuel Pressure (Optional)
5
Oil Pressure
13
Battery and Generator Currents
6
Oil Temperature
14
Battery and Essential Bus Voltages
7
CAS Display
15
8
Cabin Pressure Altitude and Change
Rate
Elevator, Aileron, and Rudder Trim
and Flap Position
ELECTRICAL SYSTEM
1) Select the SYSTEM Softkey to display the softkeys for the synoptics system.
2) Select the ELEC Softkey to display the Electrical System Page.
1
2
3
4
Procedures
Flight
Planning
GPS Nav
AFCS
Nav/Com/
XPDR/Audio
EAS
Flight
Instruments
Engine & Airframe Systems
Additional
Features
Hazard
Avoidance
5
6
Abnormal
Operation
11
Appendix
Annun/
Alerts
7
10
9
8
Index
Electrical Synoptics Page
6
Garmin G1000 Cockpit Reference Guide for the Socata TBM 700
190-01247-01 Rev. A
Engine & Airframe Systems
Essential Bus
2
Main Generator
8
Battery Bus Voltage
3
Ground Power Unit Door
9
Essential Bus Voltage
4
Battery
10
DC Buses 1through 4
5
Amperage
11
Main Bus
6
Battery Bus
Nav/Com/
XPDR/Audio
7
EAS
Standby Generator
Flight
Instruments
1
Disconnected
Connected
Disconnected
GPS Nav
Connected
AFCS
Active generator currents are displayed below the generator icons. A disconnected
generator is indicated in gray; the current is removed from the display and the switch
symbol is closed.
Flight
Planning
Procedures
Hazard
Avoidance
Generator Status
Selected
GPU Door Closed
Not Selected
Abnormal
Operation
GPU Door Open
Additional
Features
GPU status information is removed from the electrical diagram when the GPU door
is closed. If the GPU door is open and selected, the GPU status is shown in green;
when the door is open, but not selected, the status is shown in gray with the switch
closed. A CAS message, ‘GPU DOOR’ is generated if the GPU door is open.
Annun/
Alerts
Appendix
Index
GPU Door Status
190-01247-01 Rev. A
Garmin G1000 Cockpit Reference Guide for the Socata TBM 700
7
Battery connection status to the main bus is indicated in green; direction of
current flow is indicated with an arrow next to the current readout. If the battery is
disconnected from the main bus, the switch is closed. Battery overheating is indicated
in red with a ‘BAT OVHT’ annunciation; a CAS message is also generated.
EAS
Flight
Instruments
Engine & Airframe Systems
Disconnected
Battery Overheat
Battery Status
Battery and essential bus voltages are displayed using gauges. DC buses are shown
in green when energized. When not energized, the connection line to the main bus is
removed and the bus label is displayed in red.
Additional
Features
Hazard
Avoidance
Procedures
Flight
Planning
GPS Nav
AFCS
Nav/Com/
XPDR/Audio
Connected
Appendix
Annun/
Alerts
Abnormal
Operation
Battery and Essential Bus Low Voltage
Index
Bus Not Energized
DC Bus Status
8
Garmin G1000 Cockpit Reference Guide for the Socata TBM 700
190-01247-01 Rev. A
Engine & Airframe Systems
Essential Bus Connected to
the Main Bus
EAS
Essential Bus Connected to
the Battery Bus
Flight
Instruments
The Emergency Buses switch has two positions, UP (open) and DN (ground). If the
switch is in the UP position, the essential bus is connected to the battery bus. If the
switch is in the DN position, the essential bus is connected to the main bus.
Nav/Com/
XPDR/Audio
AFCS
GPS Nav
Essential Bus Connections
Flight
Planning
A red “X” over a component indicates invalid data or a failed unit.
Procedures
Hazard
Avoidance
Additional
Features
Abnormal
Operation
Annun/
Alerts
Appendix
Index
190-01247-01 Rev. A
Garmin G1000 Cockpit Reference Guide for the Socata TBM 700
9
FUEL SYSTEM
1) Select the SYSTEM Softkey to display the softkeys for the synoptics system.
2) Select the FUEL Softkey to display the Fuel System Page.
EAS
Flight
Instruments
Engine & Airframe Systems
Nav/Com/
XPDR/Audio
3
AFCS
4
2
6
1
7
Procedures
Flight
Planning
GPS Nav
5
Hazard
Avoidance
8
Index
Appendix
Annun/
Alerts
Abnormal
Operation
Additional
Features
9
1
Left Fuel Tank
6
Fuel Selector
2
Left Fuel Line
7
Right Fuel Tank
3
Fuel Pressure
8
Right Fuel Line
4
Engine Driven Boost Pump
9
Fuel Flow Data
5
Auxiliary Boost Pump
Fuel Synoptics Page
Status of the fuel selector is indicated between the fuel tank symbols. The mode,
automatic (AUTO) or manual (MAN) is shown beneath the fuel selector symbol.
10
Garmin G1000 Cockpit Reference Guide for the Socata TBM 700
190-01247-01 Rev. A
Engine & Airframe Systems
Switching
Right
Manual
Fuel Tank Fuel Tank Fuel Tank
Selection Selected Selection
Fuel
Selector
Off
Flight
Instruments
Left Fuel
Tank
Selected
EAS
Nav/Com/
XPDR/Audio
Fuel Selector Status
GPS Nav
Flight
Planning
Fuel Boost Pump Fuel Boost Pump Fuel Boost Pump
On
Off (Auto)
Off (Manual)
AFCS
If the auxiliary fuel boost pump is on, the symbol is displayed in green. The mode,
automatic (AUTO) or manual (MAN) is displayed next to the pump symbol. If the
boost pump is off, the symbol is shown in light blue (automatic mode) or red (manual
mode).
Procedures
Hazard
Avoidance
Auxiliary Boost Pump Status
Additional
Features
GENERAL SYSTEMS
Garmin G1000 Cockpit Reference Guide for the Socata TBM 700
Index
190-01247-01 Rev. A
Appendix
Invalid sensor information is indicated with a red ‘X’.
Annun/
Alerts
The General Synoptics Page aircraft diagram displays open doors in red (CAS messages also generated). Statuses of stall sensor, propeller, and pitot probes heat are also
indicated on the diagram:
• White indicates that heat is off (propeller)
• Green indicates heat is on
• Yellow indicates heat has failed (stall sensor, propeller and pitot tube).
Abnormal
Operation
1) Select the SYSTEM Softkey to display the softkeys for the synoptics system.
2) Select the GEN Softkey to display the Fuel System Page.
11
Engine & Airframe Systems
7
EAS
Flight
Instruments
6
Nav/Com/
XPDR/Audio
5
4
8
AFCS
3
GPS Nav
2
Additional
Features
Hazard
Avoidance
Procedures
Flight
Planning
1
1
Rear Cargo Door Open
5
Pitot Probe 2
2
Cabin Door Open
6
Forward Cargo Door Open
3
Pilot Door Open
7
Propeller Heaters
4
Pitot Probe 1
8
Stall Warning Sensor
Index
Appendix
Annun/
Alerts
Abnormal
Operation
General Synoptics Page
12
Garmin G1000 Cockpit Reference Guide for the Socata TBM 700
190-01247-01 Rev. A
Nav/Com/XPDR/Audio Panel
Flight
Instruments
NAV/COM/TRANSPONDER/AUDIO PANEL
ENTER OR CHANGE FLIGHT ID
Turn the small FMS Knob to enter the first character.
3)
Turn the large FMS Knob to select the next field.
4)
Turn the small FMS Knob to enter the next desired character.
5)
Repeat steps 3 and 4 until the desired Flight ID is entered.
6)
Press the ENT Key to update the Flight ID. Do not perform any other
G1000 functions until ‘updating’ is no longer displayed.
AFCS
2)
GPS Nav
Turn the large FMS Knob to select the next desired field.
4)
Turn the small FMS Knob to enter the desired number.
5)
Repeat steps 3 and 4 until the desired ADF frequency is entered.
6)
Press the ENT Key to accept the new frequency.
7)
Press the ENT Key again to transfer the frequency to the active field.
8)
Turn the large FMS Knob to select the MODE field.
9)
Turn the small FMS Knob to select ANT, ADF, ADF/BFO, or ANT/BFO.
Abnormal
Operation
3)
Additional
Features
Turn the small FMS Knob to enter the first digit of the desired ADF
frequency.
Hazard
Avoidance
2)
Procedures
Press the ADF/DME Softkey.
Flight
Planning
ADF TUNING (OPTIONAL)
1)
Nav/Com/
XPDR/Audio
Press the TMR/REF Softkey, then turn the large FMS Knob to highlight the
Flight ID field.
EAS
1)
10) Press the ENT Key to complete the selection.
Annun/
Alerts
DME TUNING
2)
Turn the large FMS to select the DME source field.
3)
Turn the small FMS Knob to select the desired Nav radio.
4)
Press the ENT Key to complete the selection.
190-01247-01 Rev. A
Garmin G1000 Cockpit Reference Guide for the Socata TBM 700
Index
Press the ADF/DME or DME Softkey.
Appendix
1)
13
ENTER A TRANSPONDER CODE
1)
Press the XPDR Softkey to display the transponder mode selection softkeys.
2)
If two transponders are available, press XPDR1 or XPDR2 to set the active
transponder. Otherwise, proceed to step 3.
3)
Press the CODE Softkey to display the transponder code selection softkeys,
for digit entry.
4)
Use the digit keys to enter the code in the code field. When entering the
code, the next key in sequence must be pressed within 10 seconds, or the
entry is cancelled and restored to the previous code. Five seconds after the
fourth digit has been entered, the transponder code becomes active.
SELECTING A COM RADIO
Transmit/Receive
Press the COM1 MIC, COM2 MIC, or COM3 MIC Key (HF, if installed) on
the audio panel.
Flight
Planning
GPS Nav
AFCS
Nav/Com/
XPDR/Audio
EAS
Flight
Instruments
Nav/Com/XPDR/Audio Panel
Press the COM1, COM2, or COM3 Key (HF, if installed) on the audio panel.
SELECTING A NAV RADIO
1)
To begin navigating using a navigation radio, press the CDI Softkey on the
PFD to select VOR1/LOC1 (NAV1) or VOR2/LOC2 (NAV2).
2)
Press the NAV1, NAV2, DME, or ADF Key on the audio panel to select or
deselect the navigation radio audio source. All radio keys can be selected
individually or together.
1)
Press the small tuning knob to select the desired radio for tuning. A light
blue box highlights the radio frequency to be tuned.
Appendix
NAV/COM TUNING
2)
Turn the respective tuning knobs to enter the desired frequency into the
standby frequency field. The large knob enters MHz and the small knob
enters kHz.
Index
Annun/
Alerts
Abnormal
Operation
Additional
Features
Hazard
Avoidance
Procedures
Receive Only
3)
Press the Frequency Transfer Key to place the frequency into the active
frequency field.
14
Garmin G1000 Cockpit Reference Guide for the Socata TBM 700
190-01247-01 Rev. A
Nav/Com/XPDR/Audio Panel
Additional
Features
Abnormal
Operation
Annun/
Alerts
Appendix
Index
15
Hazard
Avoidance
Garmin G1000 Cockpit Reference Guide for the Socata TBM 700
Procedures
190-01247-01 Rev. A
Flight
Planning
A flight plan must be filed prior to logging on to the CPDLC system. After entering
flight plan information in the required fields and successfully logging on to the system,
messages may be sent and received.
The following parameters are used to log on to the system:
• Facility
• Flight ID
• Destination Airport
• Filed Departure Airport
• File Departure Time (Optional)
GPS Nav
Connecting to the CPDLC System
AFCS
The CPDLC (Controller Pilot Data Link Communications) system provides data link
communication between the aircraft and an Air Traffic Control facility. Communication
is normally in the form of text message elements that resemble phraseology used in
voice communications with ATC.
Generally, messages are closed with an acknowledgement or acceptance. When a
message is acknowledged, the connection with the ATC facility is not terminated, but
kept active for future communication.
Communication hand-off to the next ATC facility is usually performed automatically,
but may also be accomplished manually by the pilot.
Nav/Com/
XPDR/Audio
CONTROLLER PILOT DATA LINK COMMUNICATIONS (OPTIONAL)
EAS
Pressing the INTR COM Key on either Audio Panel selects and deselects the
intercom on both Audio Panels. The annunciator is lit when the intercom is active.
The intercom connects the pilot and copilot together. Either the pilot or copilot may
select or deselect the intercom.
The CABIN Key initiates two way communication between the pilot or copilot and
the passengers in the cabin. The annunciator is lit when the cabin intercom is active
on either Audio Panel.
The MAN SQ Key allows either automatic or manual control of the intercom
squelch setting. Pressing the MAN SQ Key enables manual squelch control, indicated
by the MAN SQ annunciator.
During manual squelch operation, pressing the ICS Knob switches between volume
and squelch adjustment, lighting the associated annunciator beneath the knob. When
the MAN SQ annunciator is lit, the ICS Knob controls both volume and squelch. When
the MAN SQ annunciator is extinguished, the ICS Knob controls only volume.
Flight
Instruments
INTERCOM
Nav/Com/XPDR/Audio Panel
Flight
Planning
GPS Nav
AFCS
Nav/Com/
XPDR/Audio
EAS
Flight
Instruments
Performing the system log-on:
1)
From the MFD, select the CPDLC Softkey. Ensure ‘Link Available’ is
displayed in the Status Box.
2)
Select the LOGON Softkey.
3)
Turn the large FMS Knob to place the selection cursor over the Facility field.
4)
Turn the small FMS Knob to select the desired ATC facility to which the
CPDLC connection will be established.
5)
Press the ENT Key to complete the entry.
6)
Turn the large FMS Knob to place the selection cursor over the Flight ID
field.
7)
Turn the small FMS Knob to enter the Flight ID or aircraft registration
number.
8)
Press the ENT Key to complete the entry.
9)
Turn the large FMS Knob to place the selection cursor over the Destination
Airport field.
Procedures
10) Enter the identifier of the destination airport used in the filed flight plan
and press the ENT Key.
Additional
Features
Hazard
Avoidance
11) The Filed Departure Airport field is prefilled with the airport identifier
corresponding to the current aircraft location. If the flight plan was filed
using a different airport identifier, turn the large FMS Knob to place the
selection cursor over the Filed Departure Airport field, enter the departure
airport, and press the ENT Key.
Abnormal
Operation
12) (Optional) Turn the large FMS Knob to place the selection cursor over the
Filed Departure Time field.
13) (Optional) Enter the departure time used in the filed flight plan and press
the ENT Key.
Index
Appendix
Annun/
Alerts
14) Turn the large FMS Knob to place the selection cursor over SEND and
press the ENT Key. The Status immediately indicates ‘Connecting’. After
successful log-on, the Status indicates ‘Waiting For CPDLC’. Once a CPDLC
session is initiated by ATC, the Status indicates ‘Connected’ and the Current
Facility field is populated with the name of the facility. If a transfer to
another facility is needed, the Next Facility field is populated. Pressing the
LOGOFF Softkey terminates the log-on process.
16
Garmin G1000 Cockpit Reference Guide for the Socata TBM 700
190-01247-01 Rev. A
Nav/Com/XPDR/Audio Panel
Creating a message consists of choosing from a pre-determined list of requests,
entering the required information, and sending the request.
EAS
To create messages:
From the MFD, select the CPDLC Softkey.
2)
Select the NEW Softkey. The CPDLC Thread Window appears.
3)
With the Response/Request field highlighted, turn the small FMS Knob
to select the desired request from the list and press the ENT Key. For
discussion purposes, ‘Request [level]’ is selected.
4)
Highlight the Level field and enter the desired altitude. To toggle between
multiple units of measure (FT or FL), highlight the first numeric position and
turn the small FMS Knob counterclockwise.
5)
Press the ENT Key to complete the entry.
6)
Highlight the Reason field and enter the desired reason from the list.
7)
Press the ENT Key to complete the entry.
8)
Highlight the SEND Button and press the ENT Key.
Nav/Com/
XPDR/Audio
1)
AFCS
Flight
Planning
Procedures
Hazard
Avoidance
Responding to an ATC message consists of choosing from a pre-determined list
of responses or acknowledgements, then sending the response or acknowledgement.
Additional
Features
To respond to a message:
From the MFD, select the CPDLC Softkey.
2)
Turn the large FMS Knob to place the selection cursor over the desired
message and press the ENT Key.
3)
Turn the small FMS Knob to select the desired Response/Request from the
list and press the ENT Key.
4)
Highlight the SEND Button and press the ENT Key.
Abnormal
Operation
1)
Annun/
Alerts
Appendix
Viewing CPDLC Message Dialogs
17
Index
The status of a string of messages, or dialog, may be checked and past message
dialogs viewed. When G1000 power is cycled, the list of message dialogs is deleted.
Garmin G1000 Cockpit Reference Guide for the Socata TBM 700
GPS Nav
Responding to an ATC Message
190-01247-01 Rev. A
Flight
Instruments
Creating a Message
Nav/Com/XPDR/Audio Panel
1)
From the MFD, select the CPDLC Softkey.
2)
Turn the large FMS Knob to place the selection cursor over the desired
message to view and press the ENT Key.
3)
Press the ENT Key to view the CPDLC Thread.
Deleting Message Dialogs
While the G1000 deletes the list of message dialogs when power is turned off,
individual message dialogs may also be deleted manually. Message dialogs considered
closed may also be deleted.
To delete a single message dialog:
Procedures
Flight
Planning
GPS Nav
AFCS
Nav/Com/
XPDR/Audio
EAS
Flight
Instruments
To view messages:
2)
Turn the large FMS Knob to place the selection cursor over the desired
message to delete.
3)
Select the DELETE Softkey. A confirmation window appears.
4)
Highlight OK and press the ENT Key.
Hazard
Avoidance
Additional
Features
1)
From the MFD, select the CPDLC Softkey.
2)
Select the DEL ALL Softkey. A confirmation window appears.
3)
Highlight OK and press the ENT Key.
Disconnecting from the CPDLC System
After successfully initiating a CPDLC session, the LOGOFF Softkey becomes
available.
To Log-off the CPDLC System:
Annun/
Alerts
Abnormal
Operation
From the MFD, select the CPDLC Softkey.
To delete all closed message dialogs:
Appendix
Index
1)
1)
From the MFD, select the CPDLC Softkey.
2)
Select the LOGOFF Softkey.
Enabling/Disabling Data Mode
It may be desirable to disable Data Mode on the GDR 66 VHF Data Link Transceiver,
or conversely, to enable it.
18
Garmin G1000 Cockpit Reference Guide for the Socata TBM 700
190-01247-01 Rev. A
Nav/Com/XPDR/Audio Panel
From the MFD, select the CPDLC Softkey.
2)
Press the Menu Key to display the page menu.
3)
Turn the small FMS Knob to highlight ‘Disable Data Mode’ and press the
ENT Key.
EAS
1)
Flight
Instruments
To disable data mode on the GDR 66:
Nav/Com/
XPDR/Audio
To enable data mode on the GDR 66:
2)
Press the Menu Key to display the page menu.
3)
Turn the small FMS Knob to highlight ‘Enable Data Mode’ and press the
ENT Key.
GPS Nav
From the MFD, select the CPDLC Softkey.
AFCS
1)
PASSENGER ADDRESS (PA) SYSTEM
Appendix
Index
19
Annun/
Alerts
Garmin G1000 Cockpit Reference Guide for the Socata TBM 700
Abnormal
Operation
190-01247-01 Rev. A
Additional
Features
Recorded COM audio is stored in separate memory blocks. Once 2.5 minutes
of recording time have been reached, the recorder begins recording over the stored
memory blocks, starting from the oldest block.
The PLAY Key controls the play function. The PLAY annunciator flashes to indicate
when play is in progress. The PLAY annunciator turns off after playback is finished.
Pressing the PLAY Key once plays the latest recorded memory block and then
returns to normal operation. Pressing the PLAY Key again during play of a memory
block stops play. If a COM input signal is detected during play of a recorded memory
block, play is halted.
Pressing the PLAY Key twice within one-half second while audio is playing plays
the previous block of recorded audio. Each subsequent two presses of the PLAY Key
within one-half second backtracks through the recorded memory blocks to reach and
play any recorded block.
Hazard
Avoidance
NOTE: Pressing the PLAY key on the pilot’s Audio Panel plays recorded
audio to the Pilot. Pressing the PLAY key on the Copilot’s Audio Panel plays
recorded audio to the Copilot.
Procedures
CLEARANCE RECORDER AND PLAYER
Flight
Planning
A passenger address system is provided by pressing the PA Key to deliver messages
to the passengers. The message is heard by the other pilot on the headset only if the
INTR COM Key is enabled. PA messages are one way from the flight deck to the
passengers.
Index
Appendix
Annun/
Alerts
Abnormal
Operation
Additional
Features
Hazard
Avoidance
Procedures
Flight
Planning
GPS Nav
AFCS
Nav/Com/
XPDR/Audio
EAS
Flight
Instruments
Nav/Com/XPDR/Audio Panel
Blank Page
20
Garmin G1000 Cockpit Reference Guide for the Socata TBM 700
190-01247-01 Rev. A
AFCS
An initial press of a key listed in the following table (when the flight director is not
active) activates the pilot-side flight director in the listed modes.
Modes Selected
GPS
VOR
LOC
HDG Key
Heading Select
HDG
Appendix
Approach**
PIT
PIT
GP
GS
PIT
Annun/
Alerts
APR Key
Pitch Hold (default)
Pitch Hold (default)
Glidepath
Glideslope
Pitch Hold (default)
Abnormal
Operation
Backcourse***
PIT
*Valid VNV flight plan must be entered before VNV Key press activates flight director.
***The selected navigation receiver must have a valid LOC signal before BC Key press activates flight
director.
Garmin G1000 Cockpit Reference Guide for the Socata TBM 700
21
Index
**The selected navigation receiver must have a valid VOR or LOC signal or active GPS course before
NAV or APR Key press activates flight director.
190-01247-01 Rev. A
Additional
Features
BC Key
Pitch Hold (default)
Hazard
Avoidance
Navigation**
Procedures
NAV Key
GA Switch
ROL
ROL
ROL
TO
GA
ROL
ROL
ROL
GPS
VOR
LOC
BC
Vertical
Pitch Hold (default)
PIT
Pitch Hold (default)
PIT
Pitch Hold (default)
PIT
Takeoff (on ground)
TO
Go Around (in air)
GA
Altitude Hold
ALT
Vertical Speed
VS
Vertical Path Tracking* VPTH
Flight
Planning
ALT Key
VS Key
VNV Key
Lateral
Roll Hold (default)
Roll Hold (default)
Roll Hold (default)
Takeoff (on ground)
Go Around (in air)
Roll Hold (default)
Roll Hold (default)
Roll Hold (default)
FD Key
AP Key
CWS Button
GPS Nav
Control Pressed
AFCS
FLIGHT DIRECTOR ACTIVATION
Nav/Com/
XPDR/Audio
NOTE: If the attitude information required for the default flight director modes
becomes invalid or unavailable, the autopilot automatically disengages.
EAS
NOTE: If sensor information (other than attitude) required for a flight director
mode becomes invalid or unavailable, the flight director automatically reverts
to the default mode for that axis.
Flight
Instruments
AUTOMATIC FLIGHT CONTROL SYSTEM
Index
Appendix
Annun/
Alerts
Abnormal
Operation
Additional
Features
Hazard
Avoidance
Procedures
Flight
Planning
GPS Nav
AFCS
Nav/Com/
XPDR/Audio
EAS
Flight
Instruments
AFCS
VERTICAL MODES
Vertical Mode
Pitch Hold
Selected Altitude
Armed
Altitude Hold
Vertical Speed
Description
Control Annunciation
Holds the current aircraft pitch attitude;
may be used to climb/descend to the (default)
Selected Altitude
AFCS armed to capture the altitude
displayed in the Selected Altitude
*
window
Holds the current Altitude Reference
ALT Key
Maintains the current aircraft vertical
speed; may be used to climb/descend VS Key
to the Selected Altitude
Flight Level Change, Maintains the current aircraft airspeed
IAS Hold
(in KIAS or Mach Number) while the
FLC Key
Flight Level Change, aircraft is climbing/descending to the
Selected Altitude
Mach Hold
VNAV
VNAV Target
Altitude Armed
Glidepath
Glideslope
Takeoff
Go Around
Captures and tracks the VNAV flight VNV
path
Key
AFCS armed to capture the altitude
displayed in the VNAV Target Altitude
**
window
Captures and tracks the SBAS glidepath
on approach
APR Key
Captures and tracks the ILS glideslope
on approach
Commands a preprogrammed constant
pitch attitude and wings level in
preparation for takeoff
GA
Disengages the autopilot and Switch
commands a constant preprogrammed
pitch attitude and wings level
PIT
ALTS
ALT
nnnnn ft
VS
nnnn fpm
FLC
nnn kt
FLC
M .nnn
VPTH
ALTV
GP
GS
TO
GA
* ALTS armed automatically when PIT, VS, FLC, or GA active, and under VPTH when Selected Altitude
is to be captured instead of VNAV Target Altitude
** ALTV armed automatically under VPTH when VNAV Target Altitude is to be captured instead of
Selected Altitude
22
Garmin G1000 Cockpit Reference Guide for the Socata TBM 700
190-01247-01 Rev. A
AFCS
Roll Hold
Description
Holds current aircraft roll attitude
or rolls wings level, depending on
commanded bank angle
Limits maximum commanded roll angle
Heading Select
Captures and tracks Selected Heading
HDG
GPS
Captures and tracks selected navigation
source (GPS, VOR, LOC)
NAV
Key
VOR
Flight
Planning
LOC
Captures and tracks a localizer signal
for backcourse approaches
BC Key
Procedures
BC
Hazard
Avoidance
GPS
Captures and tracks selected navigation
APR Key
source (GPS, VOR, LOC)
VAPP
Additional
Features
LOC
Annun/
Alerts
TO
GA
Switch
Appendix
Commands a constant preprogrammed
constant pitch attitude and wings level
in preparation for takeoff
Disengages autopilot and commands
a preprogrammed constant pitch
attitude and wings level
Abnormal
Operation
Go Around
*
GPS Nav
Takeoff
BANK
Key
HDG
Key
ROL
AFCS
Navigation, GPS
Arm/Capture/Track
Navigation, VOR
Enroute Arm/
Capture/Track
Navigation, LOC
Arm/Capture/Track
(No Glideslope)
Backcourse Arm/
Capture/Track
Approach, GPS
Arm/Capture/Track
Approach, VOR
Arm/Capture/Track
Approach, ILS Arm/
Capture/Track
(Glideslope Mode
automatically armed)
(default)
Nav/Com/
XPDR/Audio
Low Bank
Control Annunciation
EAS
Lateral Mode
Flight
Instruments
LATERAL MODES
GA
190-01247-01 Rev. A
Garmin G1000 Cockpit Reference Guide for the Socata TBM 700
Index
* No annunciation appears in the AFCS Status Box. The low bank angle range is indicated in green
along the Roll Scale of the Attitude Indicator.
23
Index
Appendix
Annun/
Alerts
Abnormal
Operation
Additional
Features
Hazard
Avoidance
Procedures
Flight
Planning
GPS Nav
AFCS
Nav/Com/
XPDR/Audio
EAS
Flight
Instruments
AFCS
Blank Page
24
Garmin G1000 Cockpit Reference Guide for the Socata TBM 700
190-01247-01 Rev. A
GPS Navigation
Flight
Instruments
GPS NAVIGATION
DIRECT-TO NAVIGATION
2)
3)
6)
9)
12)
1)
2)
5)
190-01247-01 Rev. A
Garmin G1000 Cockpit Reference Guide for the Socata TBM 700
25
Index
6)
Appendix
4)
) on the PFD or controller.
Turn the large FMS Knob to place the cursor in the desired selection field.
Turn the small FMS Knob to begin selecting the desired identifier, location,
etc.
Press the ENT Key.
The cursor is now flashing on ‘ACTIVATE?’. If no altitude constraint or
course is desired, press the ENT Key to activate. To enter an altitude
constraint, proceed to step 6.
Turn the large FMS Knob to place the cursor over the ‘ALT’ altitude field.
Annun/
Alerts
3)
Press the Direct-to Key (
Abnormal
Operation
Direct-to Navigation using the PFD
Additional
Features
11)
Hazard
Avoidance
10)
Procedures
8)
Flight
Planning
7)
GPS Nav
5)
) Key on the MFD Control Unit.
Enter the waypoint identifier.
Press the ENT Key to confirm the identifier. The ‘Activate?’ field is
highlighted.
If no altitude constraint or course is desired, press the ENT Key to activate.
To enter an altitude constraint, proceed to step 5.
Turn the large FMS Knob to place the cursor over the ‘VNV’ altitude field.
Enter the desired altitude.
Press the ENT Key. If the waypoint entered is an airport, the option to
select MSL or AGL is now displayed. If the waypoint is not an airport,
proceed to step 9.
Turn the small FMS Knob to select ‘MSL’ or ‘AGL’.
Press the ENT Key. The cursor is now flashing in the VNV offset distance
field.
Enter the desired offset distance before (-) the waypoint.
Press the ENT Key. The ‘Activate?’ field is highlighted.
Press the ENT Key to activate.
AFCS
4)
Press the Direct-to (
Nav/Com/
XPDR/Audio
1)
EAS
Direct-to Navigation using the MFD
EAS
Flight
Instruments
GPS Navigation
7)
Turn the small FMS Knob to enter the desired altitude.
8)
Press the ENT Key. If the waypoint entered is an airport, the option to
select MSL or AGL is now displayed. If the waypoint is not an airport,
proceed to step 10.
9)
Turn the small FMS Knob to select ‘MSL’ or ‘AGL’.
Nav/Com/
XPDR/Audio
10) Press the ENT Key. The cursor is placed in the ‘OFFSET’ field.
11) Turn the small FMS Knob to enter the desired target altitude offset from
the selected Direct-to.
AFCS
12) Press the ENT Key to highlight ‘Activate?’ or turn the large FMS Knob to
highlight the ‘CRS’ field.
14) Press the ENT Key to highlight ‘ACTIVATE?’.
15) Press the ENT Key again to activate the Direct-to.
ACTIVATE A STORED FLIGHT PLAN
1)
Press the FPL Key and turn the small FMS Knob to display the Flight Plan
Catalog Page.
2)
Press the FMS Knob to activate the cursor.
3)
Turn the large FMS Knob to highlight the desired flight plan
4)
Select the ACTIVE Softkey. The confirmation window is now displayed.
5)
With ‘OK’ highlighted, press the ENT Key to activate the flight plan. To cancel
the flight plan activation, turn the large FMS Knob to highlight ‘CANCEL’ and
press the ENT Key.
ACTIVATE A FLIGHT PLAN LEG
Annun/
Alerts
Abnormal
Operation
Additional
Features
Hazard
Avoidance
Procedures
Flight
Planning
GPS Nav
13) Turn the small FMS Knob to enter the desired course to the waypoint.
1)
From the Active Flight Plan Page, press the FMS Knob to activate the cursor
and turn the large FMS Knob to highlight the desired waypoint.
2)
Select the ACT LEG Softkey.
Appendix
OR
Index
Press the MENU Key, select the ‘Activate Leg’ option from the page menu
and press the ENT Key. This step must be used when activating a leg from
the PFD.
3)
26
With ‘Activate’ highlighted, press the ENT Key.
Garmin G1000 Cockpit Reference Guide for the Socata TBM 700
190-01247-01 Rev. A
GPS Navigation
Flight
Instruments
STOP NAVIGATING A FLIGHT PLAN
2)
Press the MENU Key to display the Page Menu Window.
3)
Turn the large FMS Knob to highlight ‘Delete Flight Plan’ and press the ENT
Key. With ‘OK’ highlighted, press the ENT Key to deactivate the flight plan.
This will not delete the stored flight plan, only the active flight plan.
VERTICAL NAVIGATION (VNAV)
AFCS
GPS Nav
The navigation database only contains altitudes for procedures that call for “Cross
at” altitudes. If the procedure states “Expect to cross at,” the altitude is not in the
database. In this case the altitude may be entered manually.
Nav/Com/
XPDR/Audio
Press the FPL Key to display the Active Flight Plan Page.
EAS
1)
Flight
Planning
Procedures
Large White
Text
Large Light
Blue Text
Hazard
Avoidance
Small Light
Blue Text
Abnormal
Operation
Small White Text
with Altitude
Restriction Bar
Additional
Features
Small Light
Blue Subdued
Text
Annun/
Alerts
Cross AT or ABOVE 5,000 ft
Appendix
Cross AT 2,300 ft
Cross AT or BELOW 3,000 ft
Index
190-01247-01 Rev. A
Garmin G1000 Cockpit Reference Guide for the Socata TBM 700
27
Since altitudes loaded with an arrival procedure are published only for turbojet
aircraft, the altitudes are displayed as white text indicating that the altitudes are
displayed for reference only. An arrival waypoint altitude may be used (or “designated”)
as is, or changed to a different altitude. An altitude is designated by pressing the FMS
Knob and turning the large FMS Knob to place the cursor on the desired altitude and
pressing the ENT Key or entering a different value and pressing the ENT Key. The
altitude is now displayed as blue text, indicating that the altitude is now designated to
give vertical speed and deviation guidance.
Approach waypoint altitude constraints are designated in the same way as
previously described for arrivals. These altitudes are also displayed as blue text after
being designated for use. Waypoint altitude constraints may be designated up to, but
not including the FAF. The FAF is always a “reference only” altitude and cannot be
designated, unless the selected approach does not provide vertical guidance. In this
case, the FAF altitude can be designated.
White Text
Light Blue Text
Light Blue
Subdued Text
Large Text Altitude calculated by
the system estimating
the altitude of the
aircraft as it passes over
the navigation point.
This altitude is provided
as a reference and is
not designated to be
used in determining
vertical flight path
guidance.
Altitude has been
entered by the pilot.
Altitude is designated
for use in giving vertical
flight path guidance.
Altitude does not match
the published altitude
in navigation database
or no published altitude
exists.
The system cannot
use this altitude
in determining
vertical flight path
guidance.
Small Text Altitude is not
designated to be used
in determining vertical
flight path guidance.
Altitude has been
retrieved from the
navigation database
and is provided as a
reference.
Altitude is designated for
use in giving vertical flight
path guidance. Altitude
has been retrieved from
the navigation database
or has been entered by
the pilot and matches a
published altitude in the
navigation database.
The system cannot
use this altitude in
determining vertical
flight path guidance.
Index
Appendix
Annun/
Alerts
Abnormal
Operation
Additional
Features
Hazard
Avoidance
Procedures
Flight
Planning
GPS Nav
AFCS
Nav/Com/
XPDR/Audio
EAS
Flight
Instruments
GPS Navigation
28
Garmin G1000 Cockpit Reference Guide for the Socata TBM 700
190-01247-01 Rev. A
Flight Planning
Flight
Instruments
FLIGHT PLANNING
WEIGHT PLANNING
EAS
All procedures apply to the MFD unless otherwise stated.
Entering Weight Parameters
Procedures
3)
Select the FOB SYNC Softkey to enter the fuel on board quantity as read
from the aircraft fuel quantity sensors.
Additional
Features
Turn the large FMS Knob to place the cursor in the ‘FUEL ON BOARD’ field.
Or:
Annun/
Alerts
Press the FMS Knob to remove the cursor.
Abnormal
Operation
Manually enter the desired fuel quantity.
6)
Hazard
Avoidance
2)
Enter the desired reserve fuel quantity.
Flight
Planning
If necessary, press the FMS Knob to activate the cursor.
5)
GPS Nav
1)
Press the ENT Key. The cursor is now in the ‘FUEL RESERVES’ field.
AFCS
Entering Fuel Parameters
4)
Nav/Com/
XPDR/Audio
The Weight Planning Page is displayed after system power-up. If it is necessary to
return to this page, turn the large FMS Knob to select the ‘AUX’ page group. Turn the
small FMS Knob to select the first rectangular page icon.
1) Select the EMPTY WT Softkey to place the cursor in the Basic Empty
Weight field.
2) Enter the desired aircraft empty weight.
3) Press the ENT Key. The cursor is now over the ‘PILOT & STORES’ field.
4) Enter the desired weight of Pilot & Stores.
5) Press the ENT Key.
6) Continue repeating these steps until all desired weights have been entered.
TRIP PLANNING
Appendix
Turn the large FMS Knob to select the ‘AUX’ page group.
2)
Turn the small FMS Knob to select the second rectangular page icon.
3)
The current ‘PAGE MODE’ is displayed at the top of the page: ‘AUTOMATIC’
or ‘MANUAL’. To change the page mode, select the AUTO or MANUAL
Softkey.
190-01247-01 Rev. A
Garmin G1000 Cockpit Reference Guide for the Socata TBM 700
29
Index
1)
Flight Planning
Flight
Instruments
4)
For Direct-to planning:
a) Select the WPTS Softkey and verify that the starting waypoint field
indicates ‘P.POS’ (present position).
EAS
b) If necessary, press the MENU Key and select ‘Set WPT to Present
Position’ to display ‘P.POS’.
Nav/Com/
XPDR/Audio
c) Press the ENT Key and the flashing cursor moves to the ending
waypoint field.
AFCS
d) Enter the identifier of the ending waypoint and press the ENT Key to
accept the waypoint.
Or:
GPS Nav
For point-to-point planning:
a) Enter the identifier of the starting waypoint.
Flight
Planning
b) Once the waypoint’s identifier is entered, press the ENT Key to accept
the waypoint. The flashing cursor moves to the ending waypoint.
c) Again, enter the identifier of the ending waypoint.
Procedures
d) Press the ENT Key to accept the waypoint.
Or:
Hazard
Avoidance
For flight plan leg planning:
a) Select the FPL Softkey (at the bottom of the display).
Additional
Features
b) Turn the small FMS Knob to select the desired flight plan (already
stored in memory), by number.
c) Turn the large FMS Knob to highlight the ‘LEG’ field.
Annun/
Alerts
Abnormal
Operation
d) Turn the small FMS Knob to select the desired leg of the flight plan, or
select ‘CUM’ to apply trip planning calculations to the entire flight plan.
Selecting ‘FPL 00’ displays the active flight plan. If an active flight plan
is selected, ‘REM’ will be an available option to display planning data
for the remainder of the flight plan.
Appendix
NOTE: The page mode must be set to ‘MANUAL’ to perform the following
steps.
5)
Turn the large FMS Knob to highlight the departure time (DEP TIME) field.
Index
NOTE: The departure time on the Trip Planning Page is used for preflight
planning. Refer to the Utility Page for the actual flight departure time.
30
Garmin G1000 Cockpit Reference Guide for the Socata TBM 700
190-01247-01 Rev. A
Flight Planning
8)
The flashing cursor moves to the fuel flow field. Enter the fuel flow. Press
the ENT Key when finished. Note that in ‘AUTOMATIC’ page mode, fuel flow
is provided by the system.
9)
The flashing cursor moves to the fuel onboard field. Modify the fuel onboard.
Press the ENT Key when finished. In ‘AUTOMATIC’ mode, fuel onboard is
provided by the entry made on the Weight Planning Page.
Abnormal
Operation
3)
Select the NEW Softkey. A waypoint is created at the current aircraft
position.
4)
Enter the desired waypoint name.
5)
Press the ENT Key.
190-01247-01 Rev. A
Garmin G1000 Cockpit Reference Guide for the Socata TBM 700
Index
Turn the small FMS Knob to select the User WPT Information Page.
Appendix
2)
Annun/
Alerts
Turn the large FMS Knob on the MFD Control Unit to select the ‘WPT’ page
group.
Additional
Features
CREATE A USER WAYPOINT DEFINED BY LATITUDE & LONGITUDE
1)
Hazard
Avoidance
13) The flashing cursor moves to the air temperature (TOTAL AIR TEMP) field. Enter
the desired air temperature. Press the ENT Key when finished. Note that in
‘AUTOMATIC’ page mode, air temperature is provided by the system outside
air temperature.
Procedures
12) The flashing cursor moves to the barometric setting (PRESSURE) field. Enter
the desired baro setting. Press the ENT Key when finished. Note that in
‘AUTOMATIC’ page mode, the baro setting is provided by the setting entered
on the PFD.
Flight
Planning
11) The flashing cursor moves to the altitude (IND ALTITUDE) field. Enter the
altitude. Press the ENT Key when finished. Note that in ‘AUTOMATIC’ page
mode, altitude is provided by the system.
GPS Nav
10) The flashing cursor moves to the calibrated airspeed (CALIBRATED AS) field.
Enter the calibrated airspeed. Press the ENT Key when finished. Note that
in ‘AUTOMATIC’ page mode, calibrated airspeed is provided by the system.
AFCS
The flashing cursor moves to the ground speed (GS) field. Enter the ground
speed. Press the ENT Key when finished. Note that in ‘automatic’ page
mode, ground speed is provided by the system.
Nav/Com/
XPDR/Audio
7)
EAS
Enter the departure time. Press the ENT Key when finished. Departure time
may be entered in local or UTC time, depending upon system settings.
Flight
Instruments
6)
31
Flight Planning
Flight
Instruments
6)
The cursor is now in the ‘WAYPOINT TYPE’ field. If desired, the waypoint
can be made temporary (deleted automatically when the system is turned
off). If the waypoint is to remain in the system, proceed to step 7.
EAS
a) Turn the large FMS Knob one click to the left to highlight
‘TEMPORARY’.
Nav/Com/
XPDR/Audio
With the cursor in the ‘WAYPOINT TYPE’ field, turn the small FMS Knob to
display a list of waypoint types.
8)
Turn the small FMS Knob to select LAT/LON (latitude and longitude).
9)
Press the ENT Key.
CREATE A USER WAYPOINT DEFINED BY RADIALS FROM OTHER WAYPOINTS
1)
Turn the large FMS Knob on the MFD Control Unit to select the ‘WPT’ page
group.
2)
Turn the small FMS Knob to select the User WPT Information Page.
3)
Select the NEW Softkey. A waypoint is created at the current aircraft
position.
4)
Enter the desired waypoint name.
5)
Press the ENT Key.
6)
The cursor is now in the ‘WAYPOINT TYPE’ field. If desired, the waypoint
can be made temporary (deleted automatically when the system is turned
off). If the waypoint is to remain in the system, proceed to step 7.
Additional
Features
Hazard
Avoidance
Procedures
Flight
Planning
GPS Nav
7)
AFCS
b) Press the ENT Key to place a check-mark in the box. Turn the large
FMS Knob to place the cursor back in the ‘WAYPOINT TYPE’ field.
Abnormal
Operation
a) Turn the large FMS Knob one click to the left to highlight
‘TEMPORARY’.
Appendix
Annun/
Alerts
b) Press the ENT Key to place a check-mark in the box. Turn the large
FMS Knob to place the cursor back in the ‘WAYPOINT TYPE’ field.
7)
With the cursor in the ‘WAYPOINT TYPE’ field, turn the small FMS Knob to
display a list of waypoint types.
8)
Turn the small FMS Knob to select RAD/RAD (radial/radial).
9)
Press the ENT Key.
Index
10) The cursor moves to the ‘REFERENCE WAYPOINTS’ field. With the first
waypoint name highlighted, use the FMS Knobs to enter the desired
waypoint name. Waypoints may also be selected as follows:
32
Garmin G1000 Cockpit Reference Guide for the Socata TBM 700
190-01247-01 Rev. A
Flight Planning
b) Turn the large FMS Knob to select the desired waypoint.
EAS
c) Press the ENT Key.
Flight
Instruments
a) When a flight plan is active, turning the small FMS Knob to the left will
display a list of the flight plan waypoints.
Or:
AFCS
b) Turn the small FMS Knob to the right to display the ‘NRST’ airports to
the aircraft’s current position.
Nav/Com/
XPDR/Audio
a) Turn the small FMS Knob to the left. Initially, a flight plan waypoint list
is displayed.
c) Turn the large FMS Knob to select the desired waypoint.
GPS Nav
d) Press the ENT Key.
Or:
Procedures
b) Turn the small FMS Knob to the right to display the ‘RECENT’
waypoints.
Flight
Planning
a) Turn the small FMS Knob to the left. Initially, a flight plan waypoint list
is displayed.
c) Turn the large FMS Knob to select the desired waypoint.
d) Press the ENT Key.
b) Turn the small FMS Knob to the right to display the ‘USER’ waypoints.
c) Turn the large FMS Knob to select the desired waypoint.
12) Press the ENT Key.
Annun/
Alerts
11) Press the ENT Key. The cursor is displayed in the ‘RAD’ (radial) field. Enter
the desired radial from the reference waypoint.
Abnormal
Operation
d) Press the ENT Key.
Additional
Features
a) Turn the small FMS Knob to the left. Initially, a flight plan waypoint list
is displayed.
Hazard
Avoidance
Or:
13) Repeat step 10 to enter the next waypoint name.
Index
15) Press the ENT Key.
16) Press the FMS Knob to remove the flashing cursor.
190-01247-01 Rev. A
Garmin G1000 Cockpit Reference Guide for the Socata TBM 700
Appendix
14) Press the ENT Key. The cursor is displayed in the ‘RAD’ (radial) field for the
second waypoint. Enter the desired radial from the reference waypoint.
33
CREATE A USER WAYPOINT DEFINED BY A RADIAL & DISTANCE FROM
ANOTHER WAYPOINT
1)
Turn the large FMS Knob on the MFD Control Unit to select the ‘WPT’ page
group.
2)
Turn the small FMS Knob to select the User WPT Information Page.
3)
Select the NEW Softkey. A waypoint is created at the current aircraft
position.
4)
Enter the desired waypoint name.
5)
Press the ENT Key.
6)
The cursor is now in the ‘WAYPOINT TYPE’ field. If desired, the waypoint
can be made temporary (deleted automatically when the system is turned
off). If the waypoint is to remain in the system, proceed to step 7.
GPS Nav
AFCS
Nav/Com/
XPDR/Audio
EAS
Flight
Instruments
Flight Planning
Flight
Planning
a) Turn the large FMS Knob one click to the left to highlight
‘TEMPORARY’.
Hazard
Avoidance
Procedures
b) Press the ENT Key to place a check-mark in the box. Turn the large
FMS Knob to place the cursor back in the ‘WAYPOINT TYPE’ field.
7)
With the cursor in the ‘WAYPOINT TYPE’ field, turn the small FMS Knob to
display a list of waypoint types.
8)
Turn the small FMS Knob to select RAD/DIS (radial/distance).
9)
Press the ENT Key.
Additional
Features
10) The cursor moves to the ‘REFERENCE WAYPOINTS’ field. With the first
waypoint name highlighted, use the FMS Knobs to enter the desired
waypoint name. Waypoints may also be selected as follows:
Abnormal
Operation
a) When a flight plan is active, turning the small FMS Knob to the left will
display a list of the flight plan waypoints.
b) Turn the large FMS Knob to select the desired waypoint.
Annun/
Alerts
c) Press the ENT Key.
Or:
Appendix
a) Turn the small FMS Knob to the left. Initially, a flight plan waypoint list
is displayed.
Index
b) Turn the small FMS Knob to the right to display the ‘NRST’ airports to
the aircraft’s current position.
c) Turn the large FMS Knob to select the desired waypoint.
d) Press the ENT Key.
34
Garmin G1000 Cockpit Reference Guide for the Socata TBM 700
190-01247-01 Rev. A
Flight Planning
a) Turn the small FMS Knob to the left. Initially, a flight plan waypoint list
is displayed.
EAS
b) Turn the small FMS Knob to the right to display the ‘RECENT’
waypoints.
Flight
Instruments
Or:
Nav/Com/
XPDR/Audio
c) Turn the large FMS Knob to select the desired waypoint.
d) Press the ENT Key.
Or:
c) Turn the large FMS Knob to select the desired waypoint.
GPS Nav
b) Turn the small FMS Knob to the right to display the ‘USER’ waypoints.
AFCS
a) Turn the small FMS Knob to the left. Initially, a flight plan waypoint list
is displayed.
d) Press the ENT Key.
Procedures
12) Press the ENT Key.
13) The cursor is now displayed in the ‘DIS’ (distance) field. Enter the desired
distance from the reference waypoint.
Hazard
Avoidance
14) Press the ENT Key.
15) Press the FMS Knob to remove the flashing cursor.
Additional
Features
DELETE A USER WAYPOINT
Turn the large FMS Knob to select the ‘WPT’ page group.
2)
Turn the small FMS Knob to select the User WPT Information Page.
3)
Press the FMS Knob to activate the cursor.
4)
Turn the large FMS Knob to the place the cursor in the ‘USER WAYPOINT LIST’
field.
5)
Turn the small FMS Knob to highlight the desired waypoint.
6)
Select the DELETE Softkey.
7)
The message ‘Would you like to delete the user waypoint?’ is displayed. With
‘YES’ highlighted, press the ENT Key.
Appendix
Index
35
Annun/
Alerts
Garmin G1000 Cockpit Reference Guide for the Socata TBM 700
Abnormal
Operation
1)
190-01247-01 Rev. A
Flight
Planning
11) Press the ENT Key. The cursor is displayed in the ‘RAD’ (radial) field. Enter
the desired radial from the reference waypoint.
CREATE A FLIGHT PLAN
NOTE: When creating a flight plan in the Active Flight Plan Window, the first
leg is activated automatically after it is created.
EAS
Flight
Instruments
Flight Planning
Procedures
Flight
Planning
GPS Nav
AFCS
Nav/Com/
XPDR/Audio
Creating an active flight plan:
1) Press the FPL Key.
2) Press the FMS Knob to activate the cursor (only on MFD).
3) Turn the small FMS Knob to display the Waypoint Information Window.
(Turning it clockwise displays a blank Waypoint Information Window,
turning it counter-clockwise displays the Waypoint Information Window
with a waypoint selection submenu allowing selection of active flight plan,
nearest, recent, user, or airway waypoints).
4) Enter the identifier, facility, or city name of the departure waypoint or select
a waypoint from the submenu of waypoints and press the ENT Key. The
active flight plan is modified as each waypoint is entered.
5) Repeat step numbers 3 and 4 to enter each additional flight plan waypoint.
6) When all waypoints have been entered, press the FMS Knob to remove the
cursor.
Index
Appendix
Annun/
Alerts
Abnormal
Operation
Additional
Features
Hazard
Avoidance
Creating a stored flight plan:
1) Press the FPL Key.
2) Turn the small FMS Knob clockwise to display the Flight Plan Catalog Page.
3) Select the NEW Softkey; or press the MENU Key, highlight ‘Create New
Flight Plan’, and press the ENT Key to display a blank flight plan for the
first empty storage location.
4) Turn the small FMS Knob to display the Waypoint Information Window.
(Turning it clockwise displays a blank Waypoint Information Window,
turning it counter-clockwise displays the Waypoint Information Window
with a waypoint selection submenu allowing selection of active flight plan,
nearest, recent, user, or airway waypoints).
5) Enter the identifier, facility, or city name of the departure waypoint or select
a waypoint from the submenu of waypoints and press the ENT Key.
6) Repeat step numbers 4 and 5 to enter each additional flight plan waypoint.
7) When all waypoints have been entered, press the FMS Knob to return to
the Flight Plan Catalog Page. The new flight plan is now in the list.
36
Garmin G1000 Cockpit Reference Guide for the Socata TBM 700
190-01247-01 Rev. A
Flight Planning
Insert the SD card containing the flight plan in the top card slot on the
MFD.
2)
Press the FPL Key on the MFD Control Unit to display the Active Flight Plan
Page on the MFD.
3)
Turn the small FMS Knob to select the Flight Plan Catalog Page.
4)
Press the FMS Knob to activate the cursor.
Nav/Com/
XPDR/Audio
5)
Turn either FMS Knob to highlight an empty or existing flight plan.
6)
Select the IMPORT Softkey.
AFCS
1)
EAS
Flight
Instruments
IMPORT A FLIGHT PLAN FROM AN SD CARD
Or:
Press the ENT Key.
Additional
Features
8)
Hazard
Avoidance
Turn the small FMS Knob to highlight the desired flight plan for importing.
Procedures
7)
Flight
Planning
If an existing flight plan is selected, an ‘Overwrite existing flight plan?
OK or CANCEL’ prompt is displayed. Press the ENT Key to choose to
overwrite the selected flight plan and see a list of the available flight
plans on the SD card. If overwriting the existing flight plan is not
desired, select ‘CANCEL’ using the FMS Knob, press the ENT Key, select
another existing or empty flight plan, and again select the IMPORT
Softkey.
GPS Nav
If an empty flight plan is selected, a list of the available flight plans on
the SD card will be displayed.
INSERT A WAYPOINT IN THE ACTIVE FLIGHT PLAN
Press the FPL Key to display the active flight plan.
2)
If necessary, press the FMS Knob to activate the cursor.
3)
Turn the large FMS Knob to highlight the desired flight plan waypoint. The
new waypoint is inserted before the highlighted waypoint.
4)
Turn the small FMS Knob. The Waypoint Information Window is now
displayed.
5)
Enter the new flight plan waypoint by one of the following:
Abnormal
Operation
1)
Annun/
Alerts
Appendix
a) Enter the user waypoint identifier, facility, or city.
Index
b) Press the ENT Key.
Or:
190-01247-01 Rev. A
Garmin G1000 Cockpit Reference Guide for the Socata TBM 700
37
Flight Planning
Flight
Instruments
a) Turn the small FMS Knob to the left. Initially, a flight plan waypoint list
is displayed.
EAS
b) Turn the small FMS Knob to the right to display the ‘NRST’ airport
waypoints to the aircraft’s current position.
c) Turn the large FMS Knob to select the desired waypoint.
Nav/Com/
XPDR/Audio
d) Press the ENT Key.
Or:
AFCS
a) Turn the small FMS Knob to the left. Initially, a flight plan waypoint list
is displayed.
c) Turn the large FMS Knob to select the desired waypoint.
d) Press the ENT Key.
e) Press the ENT Key again to “accept” the waypoint.
ENTER AN AIRWAY IN A FLIGHT PLAN
1)
Press the FPL Key.
2)
Press the FMS Knob to activate the cursor (not required on the PFD).
3)
Turn the large FMS Knob to highlight the waypoint field after the desired
airway entry point. If this previous waypoint is not a valid airway entry
point, a valid entry point should be entered at this time.
4)
Turn the small FMS Knob one click clockwise and select the LD AIRWY
Softkey, or press the MENU Key and select “Load Airway”. The Select
Airway Page is displayed. The LD AIRWY Softkey or the “Load Airway”
menu item is available only when an acceptable airway entry waypoint has
been chosen (the waypoint ahead of the cursor position).
5)
Turn the FMS Knob to select the desired airway from the list, and press the
ENT Key. Low altitude airways are shown first in the list, followed by “all”
altitude airways, and then high altitude airways.
6)
Turn the FMS Knob to select the desired airway exit point from the list, and
press the ENT Key. ‘LOAD?’ is highlighted.
7)
Press the ENT Key. The system returns to editing the flight plan with the
new airway inserted.
Index
Appendix
Annun/
Alerts
Abnormal
Operation
Additional
Features
Hazard
Avoidance
Procedures
Flight
Planning
GPS Nav
b) Turn the small FMS Knob to the right to display the ‘RECENT’
waypoints.
38
Garmin G1000 Cockpit Reference Guide for the Socata TBM 700
190-01247-01 Rev. A
Flight Planning
2)
Press the MENU Key to display the Page Menu.
3)
Turn the large FMS Knob to highlight ‘Invert Flight Plan’.
4)
Press the ENT Key. The original flight plan remains intact in its flight plan
catalog storage location.
5)
With ‘OK’ highlighted, press the ENT Key to invert the flight plan.
Nav/Com/
XPDR/Audio
Press the FPL Key to display the active flight plan.
EAS
1)
Flight
Instruments
INVERT AN ACTIVE FLIGHT PLAN
Press the FPL Key to display the active flight plan. Press the FMS Knob to
activate the cursor.
Flight
Planning
Or, for a stored flight plan:
GPS Nav
1)
AFCS
REMOVE A DEPARTURE, ARRIVAL, APPROACH, OR AIRWAY FROM A FLIGHT
PLAN
a) Press the MFD FPL Key and turn the small FMS Knob to select the
Flight Plan Catalog Page.
Procedures
b) Press the FMS Knob to activate the cursor.
c) Turn the large FMS Knob to highlight the desired flight plan.
3)
Press the CLR Key to display a confirmation window.
4)
With ‘OK’ highlighted, press the ENT Key to remove the selected procedure
or airway.
Abnormal
Operation
Turn the large FMS Knob to highlight the title for the approach, departure,
arrival, or airway to be deleted. Titles appear in white directly above the
procedure’s waypoints.
Additional
Features
2)
Hazard
Avoidance
d) Select the EDIT Softkey.
STORE A FLIGHT PLAN
2)
Turn the large FMS Knob to highlight ‘Store Flight Plan’ and press the ENT Key.
3)
With ‘OK’ highlighted, press the ENT Key to store the flight plan.
Appendix
After creating a flight plan on either the PFD or MFD, it may be saved by
pressing the MENU Key.
Annun/
Alerts
1)
Index
190-01247-01 Rev. A
Garmin G1000 Cockpit Reference Guide for the Socata TBM 700
39
EDIT A STORED FLIGHT PLAN
1)
Press the FPL Key for the MFD and turn the small FMS Knob to display the
Flight Plan Catalog Page.
2)
Press the FMS Knob to activate the cursor.
3)
Turn the large FMS Knob to highlight the desired flight plan.
4)
Select the EDIT Softkey.
5)
Turn the large FMS Knob to place the cursor in the desired location.
6)
Enter the changes, then press the ENT Key.
7)
Press the FMS Knob to return to the Flight Plan Catalog Page.
DELETE A WAYPOINT FROM THE FLIGHT PLAN
1)
Flight
Planning
GPS Nav
AFCS
Nav/Com/
XPDR/Audio
EAS
Flight
Instruments
Flight Planning
Or, for a stored flight plan:
Procedures
a) Press the FPL Key of the MFD and turn the small FMS Knob to select
the Flight Plan Catalog Page.
b) Press the FMS Knob to activate the cursor.
Hazard
Avoidance
c) Turn the large FMS Knob to highlight the desired flight plan.
Annun/
Alerts
Abnormal
Operation
Additional
Features
d) Select the EDIT Softkey.
2)
Turn the large FMS Knob to highlight the waypoint to be deleted.
3)
Press the CLR Key to display a ‘REMOVE (Wpt Name)?’ confirmation
window.
4)
With ‘OK’ highlighted, press the ENT Key to remove the waypoint. To cancel
the delete request, turn the large FMS Knob to highlight ‘CANCEL’ and press
the ENT Key.
5)
Once all changes have been made, press the FMS Knob to remove the
cursor.
INVERT AND ACTIVATE A STORED FLIGHT PLAN
Index
Appendix
Press the FPL Key to display the active flight plan. Press the FMS Knob to
activate the cursor.
40
1)
Press the FPL Key for the MFD.
2)
Turn the small FMS Knob to select the Flight Plan Catalog Page.
3)
Press the FMS Knob to activate the cursor.
Garmin G1000 Cockpit Reference Guide for the Socata TBM 700
190-01247-01 Rev. A
Flight Planning
Select the INVERT Softkey. ‘Invert and activate stored flight plan?’ is
displayed.
6)
With ‘OK’ highlighted, press the ENT Key. The selected flight plan is now
inverted and activated. The original flight plan remains intact in its flight plan
catalog storage location.
COPY A FLIGHT PLAN
Press the FPL Key for the MFD.
2)
Turn the small FMS Knob to select the Flight Plan Catalog Page.
3)
Press the FMS Knob to activate the cursor.
4)
Turn the large FMS Knob to highlight the flight plan to be copied.
5)
Select the COPY Softkey. A ‘Copy to flight plan #?’ confirmation window is
displayed.
6)
With ‘OK’ highlighted, press the ENT Key to copy the flight plan. To cancel,
turn the large FMS Knob to highlight ‘CANCEL’ and press the ENT Key.
AFCS
1)
Turn the small FMS Knob to select the Flight Plan Catalog Page.
3)
Press the FMS Knob to activate the cursor.
4)
Turn the large FMS Knob to highlight the flight plan to be deleted.
5)
Select the DELETE Softkey. A ‘Delete flight plan #?’ confirmation window is
displayed.
6)
With ‘OK’ highlighted, press the ENT Key to delete the flight plan. To cancel,
turn the large FMS Knob to highlight ‘CANCEL’ and press the ENT Key.
Hazard
Avoidance
2)
Additional
Features
Abnormal
Operation
Annun/
Alerts
GRAPHICAL FLIGHT PLAN CREATION
2)
Press the Joystick to activate the map pointer. Use the Joystick to move
the pointer to the desired point on the map to be inserted as a waypoint in
the flight plan.
41
Index
Press the FPL Key to display the Active Flight Plan Page on the MFD.
Appendix
1)
Garmin G1000 Cockpit Reference Guide for the Socata TBM 700
Procedures
Press the FPL Key for the MFD.
Flight
Planning
1)
GPS Nav
DELETE A FLIGHT PLAN
190-01247-01 Rev. A
Nav/Com/
XPDR/Audio
5)
EAS
Turn the large FMS Knob to highlight the desired flight plan.
Flight
Instruments
4)
3)
The default insertion point is at the end of the flight plan. If the selected
waypoint is to be placed anywhere other than the end of the flight plan,
press the FMS Knob to activate the cursor. Waypoints are inserted ABOVE
the cursor. Turn the large FMS Knob to select the desired insertion point.
4)
Select the LD WPT Softkey. The selected waypoint is inserted at the selected
point. The default user waypoint naming is USR000, USR001, USR002, and
so on.
5)
To change the user waypoint name, follow the procedure for modifying a user
waypoint.
EXPORT A FLIGHT PLAN TO AN SD CARD
1)
Insert the SD card into the top card slot on the MFD.
2)
Press the FPL Key on the MFD Contol Unit to display the Active Flight Plan
Page on the MFD.
3)
Turn the small FMS Knob to select the Flight Plan Catalog Page.
4)
Press the FMS Knob to activate the cursor.
5)
Turn the large FMS Knob to highlight the flight plan to be exported.
6)
Select the EXPORT Softkey.
7)
Press the ENT Key to confirm the export.
Index
Appendix
Annun/
Alerts
Abnormal
Operation
Additional
Features
Hazard
Avoidance
Procedures
Flight
Planning
GPS Nav
AFCS
Nav/Com/
XPDR/Audio
EAS
Flight
Instruments
Flight Planning
42
Garmin G1000 Cockpit Reference Guide for the Socata TBM 700
190-01247-01 Rev. A
Procedures
Flight
Instruments
PROCEDURES
LOAD AND ACTIVATE A DEPARTURE PROCEDURE
EAS
3)
Press the ENT Key. The cursor is displayed in the ‘DEPARTURE’ field with a
list of available departures.
4)
Turn the large FMS Knob to highlight the desired departure.
5)
Press the ENT Key. A list of runways may be displayed for the departure. If
so, turn either FMS Knob to select the desired runway.
6)
Press the ENT Key. The cursor is displayed in the ‘TRANSITION’ field with a
list of available transitions.
7)
Turn the large FMS Knob to highlight the desired transition.
8)
Press the ENT Key.
9)
With ‘LOAD?’ highlighted, press the ENT Key. The departure is active when
the flight plan is active.
Flight
Planning
Turn the large FMS Knob to highlight ‘SELECT DEPARTURE’.
Hazard
Avoidance
Press the FPL Key for the MFD to display the active flight plan.
2)
Press the FMS Knob to activate the cursor.
3)
Turn the large FMS Knob to highlight the TO waypoint of the desired leg
within the departure.
4)
Select the ACT LEG Softkey. A confirmation window showing the selected
leg is displayed.
5)
With ‘ACTIVATE’ highlighted, press the ENT Key.
Additional
Features
1)
Abnormal
Operation
Annun/
Alerts
LOAD AN ARRIVAL PROCEDURE
Press the PROC Key.
2)
Turn the large FMS Knob to highlight ‘SELECT ARRIVAL’.
3)
Press the ENT Key. The cursor is displayed in the ‘ARRIVAL’ field with a list
of available arrivals.
Appendix
1)
43
Index
Garmin G1000 Cockpit Reference Guide for the Socata TBM 700
Procedures
ACTIVATE A DEPARTURE LEG
190-01247-01 Rev. A
GPS Nav
2)
AFCS
Press the PROC Key.
Nav/Com/
XPDR/Audio
1)
Nav/Com/
XPDR/Audio
EAS
Flight
Instruments
Procedures
5)
Press the ENT Key. A list of transitions is displayed for the selected arrival.
6)
Turn either FMS Knob to select the desired transition.
7)
Press the ENT Key. A list of runways may be displayed for the selected
arrival.
8)
Turn the large FMS Knob to highlight the desired runway.
9)
Press the ENT Key.
10) With ‘LOAD?’ highlighted, press the ENT Key.
AFCS
11) The arrival becomes part of the active flight plan.
ACTIVATE AN ARRIVAL LEG
Procedures
Flight
Planning
GPS Nav
Turn the large FMS Knob to highlight the desired arrival.
1)
Press the FPL Key to display the active flight plan.
2)
Press the FMS Knob to activate the cursor.
3)
Turn the large FMS Knob to highlight the TO waypoint of the desired leg
within the arrival.
4)
Select the ACT LEG Softkey. A confirmation window showing the selected
leg is displayed.
5)
With ‘ACTIVATE’ highlighted, press the ENT Key.
LOAD AND/OR ACTIVATE AN APPROACH PROCEDURE
Additional
Features
Hazard
Avoidance
4)
Index
Appendix
Annun/
Alerts
Abnormal
Operation
NOTE: If certain GPS parameters (SBAS, RAIM, etc.) are not available, some
published approach procedures for the desired airport may not be displayed
in the list of available approaches.
44
1)
Press the PROC Key.
2)
Turn the large FMS Knob to highlight ‘SELECT APPROACH’.
3)
Press the ENT Key. A list of available approaches for the destination airport
is displayed.
4)
Turn either FMS Knob to highlight the desired approach.
5)
Press the ENT Key. A list of available transitions for the selected approach
procedure is now displayed.
Garmin G1000 Cockpit Reference Guide for the Socata TBM 700
190-01247-01 Rev. A
Procedures
8)
If desired, the DA/MDA for the selected approach procedure may be
entered and displayed on the PFD. Turn the small FMS Knob in the
direction of the green arrow to change the display from OFF to BARO.
9)
Press the ENT Key. The cursor moves to the altitude field. Turn the small
FMS Knob to enter the published DA/MDA for the selected approach
procedure.
AFCS
Press the ENT Key. The cursor moves to the MINIMUMS field.
Nav/Com/
XPDR/Audio
7)
EAS
Turn either FMS Knob to select the desired transition. The “Vectors”
option assumes vectors will be received to the final course segment of
the approach and will provide navigation guidance relative to the final
approach course.
Flight
Instruments
6)
GPS Nav
10) Press the ENT Key. ‘LOAD? or ACTIVATE?’ is now displayed with ‘LOAD?’
highlighted.
11) Turn the large FMS Knob to select either ‘LOAD?’ or ‘ACTIVATE?’.
Flight
Planning
Procedures
Selecting ‘LOAD?’ enters the selected approach procedure into the active
flight plan, but is not currently active. Selecting ‘ACTIVATE?’ enters the
selected approach procedure into the active flight plan and activates the
first leg of the approach.
12) Press the ENT Key.
Hazard
Avoidance
ACTIVATE AN APPROACH IN THE ACTIVE FLIGHT PLAN
Press the PROC Key.
2)
Turn the large FMS Knob to highlight ‘ACTIVATE APPROACH’.
3)
Press the ENT Key.
Additional
Features
1)
Abnormal
Operation
ACTIVATE A VECTOR TO FINAL APPROACH FIX
2)
Turn the large FMS Knob to highlight ‘ACTIVATE VECTOR-TO-FINAL’.
3)
Press the ENT Key.
4)
The final approach course becomes the active leg.
Appendix
Press the PROC Key.
Annun/
Alerts
1)
Index
190-01247-01 Rev. A
Garmin G1000 Cockpit Reference Guide for the Socata TBM 700
45
ACTIVATE A MISSED APPROACH IN THE ACTIVE FLIGHT PLAN
Nav/Com/
XPDR/Audio
EAS
Flight
Instruments
Procedures
1)
Press the PROC Key.
2)
Turn the large FMS Knob to highlight ‘ACTIVATE MISSED APPROACH’.
3)
Press the ENT Key. A confirmation window is displayed.
4)
With ‘ACTIVATE’ highlighted, press the ENT Key.
Or:
Index
Appendix
Annun/
Alerts
Abnormal
Operation
Additional
Features
Hazard
Avoidance
Procedures
Flight
Planning
GPS Nav
AFCS
Press the go-around button.
46
Garmin G1000 Cockpit Reference Guide for the Socata TBM 700
190-01247-01 Rev. A
Hazard Avoidance
Flight
Instruments
HAZARD AVOIDANCE
CUSTOMIZING THE HAZARD DISPLAYS ON THE NAVIGATION MAP
With the Navigation Map Page displayed, press the MENU Key to display
the Navigation Map Page Menu. The cursor flashes on the ‘Map Setup’
option.
2)
Press the ENT Key. The Map Setup Menu is displayed. Turn the small FMS
Knob to select ‘Weather’ to customize the display of weather features.
Select ‘Traffic’ to customize the display of traffic.
3)
Press the small FMS Knob to return to the Navigation Map Page.
EAS
1)
AFCS
Procedures
Select the STRMSCP Softkey. Select the STRMSCP Softkey again to
remove Stormscope Lightning Data from the Navigation Map Page.
Additional
Features
Lightning Age
Strike is less than 6 seconds old
Hazard
Avoidance
2)
Symbol
Abnormal
Operation
Strike is between 6 and 60 seconds old
Annun/
Alerts
Strike is between 1 and 2 minutes old
Strike is between 2 and 3 minutes old
2)
Turn either FMS Knob to highlight ‘Map Setup’.
3)
Press the ENT Key.
4)
Turn the small FMS Knob to highlight ‘Weather’.
190-01247-01 Rev. A
Garmin G1000 Cockpit Reference Guide for the Socata TBM 700
Index
Press the MENU Key (with the Navigation Map Page displayed).
Appendix
Select ‘Cell’ or ‘Strike’ as the Stormscope Lightning Mode
1)
Flight
Planning
Displaying Stormscope Lightning Data on the Navigation Map Page
Select the MAP Softkey.
GPS Nav
WARNING: The Stormscope system is not intended to be used for hazardous
thunderstorm penetration. Weather information on the G1000 MFD is
approved for weather avoidance only. Refer to the WX-500 Pilot’s Guide for
detailed operation.
1)
Nav/Com/
XPDR/Audio
STORMSCOPE® (OPTIONAL)
47
Nav/Com/
XPDR/Audio
EAS
Flight
Instruments
Hazard Avoidance
5)
Press the ENT Key.
6)
Turn the large FMS Knob to place the cursor in the ‘STRMSCP MODE’ field.
7)
Turn the small FMS Knob to display the ‘Cell/Strike’ window.
8)
Turn either FMS Knob to select ‘Cell’ or ‘Strike’. Press the ENT Key.
9)
Push the FMS Knob to return to the Navigation Map Page.
AFCS
Clear Stormscope Lightning Data from the Navigation Map Page
1)
Press the MENU Key (with the Navigation Map Page displayed).
2)
Turn either FMS Knob to highlight the ‘Clear Stormscope® Lightning’ field
and press the ENT Key.
GPS Nav
NOTE: If heading input is lost, strikes and/or cells must be cleared manually
Flight
Planning
after the execution of each turn. This is to ensure that the strike and/or cell
positions are depicted accurately in relation to the nose of the aircraft.
Procedures
Stormscope Page
1)
Turn the large FMS Knob until the Map Page group is selected.
2)
Turn the small FMS Knob until the Stormscope Page is selected.
1)
Select the Stormscope Page.
2)
Select the MODE Softkey. The CELL and STRIKE Softkeys are displayed.
Select the CELL Softkey to display ‘CELL’ data or select the STRIKE Softkey
to display ‘STRIKE’ data. ‘CELL’ or ‘STRIKE’ is displayed in the mode box
located in the upper left corner of the Stormscope Page.
Abnormal
Operation
Additional
Features
Hazard
Avoidance
Change the Stormscope Lightning Mode Between ‘Cell’ and ‘Strike’
Annun/
Alerts
NOTE: “Cell mode” uses a clustering program to identify clusters of electrical
activity that indicate cells.
Appendix
Change the Viewing Mode Between 360˚ and 120˚
1)
Select the Stormscope Page.
2)
Select the VIEW Softkey. The 360 and ARC Softkeys are displayed. Select
the 360 Softkey to display a 360˚ viewing area or select the ARC Softkey to
display a 120˚ viewing area.
Index
Select the CLEAR Softkey to remove all Stormscope lightning data from the
display.
48
Garmin G1000 Cockpit Reference Guide for the Socata TBM 700
190-01247-01 Rev. A
Hazard Avoidance
Nav/Com/
XPDR/Audio
Displaying SiriusXM Weather on the Navigation Map Page
Select the MAP Softkey.
2)
Select the NEXRAD or SiriusXM LTNG Softkey to display the desired
weather. Select the applicable softkey again to remove weather data from
the Navigation Map Page.
GPS Nav
Display METAR and TAF information on the Airport Information Page
Turn the small FMS Knob to select the Airport Information Page.
3)
Select the WX Softkey to display METAR and TAF text (METAR and TAF
information is updated every 12 minutes).
Procedures
2)
Flight
Planning
Turn the large FMS Knob to select the WPT Page Group.
AFCS
1)
1)
EAS
WARNING: Use of SiriusXM weather for hazardous weather penetration is
not recommended. Weather information provided by SiriusXM Radio Service
is approved only for weather avoidance, not penetration.
Flight
Instruments
SIRIUSXM WEATHER (OPTIONAL)
Displaying Weather on the Weather Data Link Page
Turn the large FMS Knob to select the Map Page Group.
2)
Turn the small FMS Knob to select the Weather Data Link Page.
3)
Select the available softkeys to select the desired SiriusXM weather product.
4)
Select the LEGEND Softkey to view the legends for the selected products.
If necessary, turn either FMS Knob to scroll through the list. Press the small
FMS Knob or the ENT Key to return to the map.
Hazard
Avoidance
1)
Move the Joystick to place the panning arrow on AIRMETs, TFRs, METARs,
SIGMETs, PIREPs or AIREPs.
Appendix
2)
Annun/
Alerts
Push in the Joystick to display the panning arrow.
Abnormal
Operation
1)
Additional
Features
Map Panning Information – Weather Data Link Page
Index
190-01247-01 Rev. A
Garmin G1000 Cockpit Reference Guide for the Socata TBM 700
49
Hazard Avoidance
Flight
Instruments
3)
Press the ENT Key to display pertinent information for the selected product.
Nav/Com/
XPDR/Audio
EAS
Note that pressing the ENT Key when panning over an AIRMET or a
SIGMET displays an information box that shows the text of the report.
Panning over an airport with METAR information does not display more
information but allows the user to press the ENT Key and select that
Airport’s Information Page to display the text of the report. Pressing the
ENT Key when panning over a TFR displays TFR specific information.
Weather Products and Symbols
AFCS
Wx Product
Status Icons
Description
GPS Nav
NEXRAD - Available for the US and Canada. The age of the displayed data
for each is shown at the right.
Flight
Planning
ECHO TOP - The age of the displayed data is shown at the right. Not
displayed when CLOUD TOP is displayed.
Procedures
CLOUD TOP - The age of the displayed data is shown at the right. Not
displayed when ECHO TOP is displayed.
Hazard
Avoidance
SiriusXM LIGHTNING - The age of the displayed data is shown at the right.
Additional
Features
SIGMET & AIRMET - The age of the displayed data for each is shown at the
right.
Abnormal
Operation
CELL MOVEMENT - The age of the displayed data is shown at the right.
METAR - Available for the US and Canada. The age of the displayed data for
each is shown at the right.
Appendix
Annun/
Alerts
SURFACE ANALYSIS with CITY FORECAST - The upper symbol depicts
Surface Analysis. The lower symbol depicts City Forecast. The age of the
displayed data for each is shown at the right. The selected forecast period is
shown at the bottom.
Index
FREEZING LEVEL - The age of the displayed data is shown at the right.
50
Garmin G1000 Cockpit Reference Guide for the Socata TBM 700
190-01247-01 Rev. A
Hazard Avoidance
Flight
Instruments
Wx Product
Status Icons
Description
WINDS ALOFT - Available for the US and Canada. The age of the displayed
data for each is shown at the right. The altitude selection is shown at the
bottom.
EAS
COUNTY WARNING - The age of the displayed data is shown at the right.
Nav/Com/
XPDR/Audio
CYCLONE WARNING - The age of the displayed data is shown at the right.
AFCS
AIREP - The age of the displayed data is shown at the right.
GPS Nav
PIREP - The age of the displayed data is shown at the right. Urgent Pireps
are displayed in yellow.
Flight
Planning
TURBULENCE - The age of the displayed data is shown at the right. The
altitude selection is shown at the bottom.
Procedures
ICING POTENTIAL - The age of the displayed data is shown at the right.
The altitude selection is shown at the bottom.
Hazard
Avoidance
TRAFFIC SYSTEMS
Index
51
Appendix
Garmin G1000 Cockpit Reference Guide for the Socata TBM 700
Annun/
Alerts
190-01247-01 Rev. A
Description
Non-Threat Traffic
(intruder is beyond 5 nm and greater than 1200’ vertical separation)
Proximity Advisory (PA) (Not available with TIS system)
(intruder is within 5 nm and less than 1200’ vertical separation)
Traffic Advisory (TA)
(closing rate, distance, and vertical separation meet TA criteria)
Abnormal
Operation
Traffic Symbol
Additional
Features
• If Traffic information Service (TIS) is configured, STANDBY, OPERATE, and
TNA MUTE softkeys are displayed.
• If a Traffic Advisory System (TAS) is configured, STANDBY, NORMAL, TEST,
and ALT MODE softkeys are displayed.
Hazard Avoidance
Flight
Instruments
Traffic Symbol
Description
Traffic Advisory Off Scale
EAS
Traffic Advisory (TA) arrow with ADS-B directional information. Points in
the direction of the intruder aircraft track (GTS 820 only).
Nav/Com/
XPDR/Audio
Proximity Advisory (PA) arrow with ADS-B directional information. Points
in the direction of the aircraft track (GTS 820 only).
AFCS
Non-threat traffic arrow with ADS-B directional information. Points in the
direction of the intruder aircraft track (GTS 820 only).
GPS Nav
PA or Non-threat traffic arrow with ADS-B directional information, but
positional accuracy is degraded. Points in the direction of the aircraft
track (GTS 820 only).
Flight
Planning
Traffic Symbol Description
Procedures
Traffic Information Service (TIS)
Hazard
Avoidance
NOTE: If the G1000 is configured to use an optional Traffic Advisory System
(TAS), TIS is not available for use.
Additional
Features
NOTE: Traffic Information Service (TIS) is only available when the aircraft is
within the service volume of a TIS capable terminal radar site.
Index
Appendix
Annun/
Alerts
Abnormal
Operation
Displaying Traffic on the Traffic Map Page
52
1)
Turn the large FMS Knob to select the Map Page Group.
2)
Turn the small FMS Knob to select the Traffic Map Page.
3)
Select the OPERATE Softkey to begin displaying traffic. ‘OPERATING’ is
displayed in the Traffic Mode field.
4)
Select the STANDBY Softkey to place the system in the Standby Mode.
‘STANDBY’ is displayed in the Traffic Mode field.
5)
Rotate the Joystick clockwise to display a larger area or rotate counterclockwise to display a smaller area.
6)
Select the TNA MUTE Softkey to mute the “TIS Not Available” aural alert.
Garmin G1000 Cockpit Reference Guide for the Socata TBM 700
190-01247-01 Rev. A
Hazard Avoidance
Ensure TIS is operating. With the Navigation Map displayed, select the
MAP Softkey.
2)
Select the TRAFFIC Softkey. Traffic is now displayed on the map.
EAS
1)
Flight
Instruments
Displaying Traffic on the Navigation Map
Nav/Com/
XPDR/Audio
Traffic Advisory System (TAS) (Optional)
System Self Test
Set the range to 2/6 nm.
2)
Select the STANDBY Softkey.
3)
Select the TEST Softkey.
AFCS
1)
4)
Select the ALT MODE Softkey to change the altitude volume. Select the
desired altitude volume by selecting the BELOW, NORMAL, ABOVE, or
UNREST (unrestricted) Softkey. The selection is displayed in the Altitude
Mode field.
5)
Select the STANDBY Softkey to place the system in the Standby Mode.
‘STANDBY’ is displayed in the Traffic Mode field.
6)
Rotate the Joystick clockwise to display a larger area or rotate counterclockwise to display a smaller area.
7)
Select the FLT ID Softkey (GTS 820 only) to enable or disable Flight ID
displayed with the intruder information.
Appendix
Select the NORMAL Softkey to begin displaying traffic. ‘OPERATING’ is
displayed in the Traffic Mode field.
Annun/
Alerts
3)
Abnormal
Operation
Turn the small FMS Knob to select the second rectangular page icon.
Additional
Features
2)
Hazard
Avoidance
Turn the large FMS Knob to select the Map Page Group.
Procedures
1)
Displaying Traffic on the Navigation Map
Ensure TAS is operating.
2)
With the Navigation Map displayed, select the MAP Softkey.
3)
Select the TRAFFIC Softkey. Traffic is now displayed on the map.
190-01247-01 Rev. A
Garmin G1000 Cockpit Reference Guide for the Socata TBM 700
Index
1)
Flight
Planning
Self test takes approximately eight seconds to complete. When completed
successfully, traffic symbols are displayed and a voice alert “TAS System Test
OK” is heard. If the self test fails, the system reverts to Standby Mode and
a voice alert “TAS System Test Fail” is heard.
Displaying Traffic on the Traffic Map Page
GPS Nav
4)
53
TERRAIN AND OBSTACLE PROXIMITY
NOTE: Terrain data is not displayed when the aircraft latitude is greater than
75 degrees north or 60 degrees south.
EAS
Flight
Instruments
Hazard Avoidance
1)
Turn the large FMS Knob to select the Map Page Group.
2)
Turn the small FMS Knob to select the last rectangular page icon.
3)
If desired, select the VIEW Softkey to access the ARC and 360 Softkeys.
When the ARC Softkey is selected, a radar-like 120° view is displayed.
Select the 360 Softkey to return to the 360° default display.
4)
Rotate the Joystick clockwise to display a larger area or rotate counterclockwise to display a smaller area.
Hazard
Avoidance
Procedures
Flight
Planning
GPS Nav
AFCS
Nav/Com/
XPDR/Audio
Displaying Terrain and Obstacles on the Terrain Proximity Page
Terrain/Obstacle Location
Red
Terrain/Obstacle above or within 100’
below current aircraft altitude.
Yellow
Terrain/Obstacle between 100’ and
1000’ below current aircraft altitude.
Black
Terrain/Obstacle is more than 1000’
below aircraft altitude.
Abnormal
Operation
Additional
Features
Displaying Terrain and Obstacles on the Navigation Map
1)
With the Navigation Map displayed, select the MAP Softkey.
2)
Select the TERRAIN Softkey. Terrain and obstacle proximity will now be
displayed on the map.
TERRAIN-SVS
NOTE: Terrain-SVS is only available when the Synthetic Vision System (SVS)
option is installed and the TAWS option has not been installed.
Appendix
Annun/
Alerts
Color
Index
NOTE: Terrain data is not displayed when the aircraft latitude is greater than
75 degrees north or 60 degrees south.
54
Garmin G1000 Cockpit Reference Guide for the Socata TBM 700
190-01247-01 Rev. A
Hazard Avoidance
2)
Turn the small FMS Knob to select the Terrain-SVS Page.
3)
If desired, select the VIEW Softkey to access the ARC and 360 softkeys.
When the ARC Softkey is selected, a radar-like 120° view is displayed.
Select the 360 Softkey to return to the 360° default display.
4)
Rotate the Joystick clockwise to display a larger area or rotate counterclockwise to display a smaller area.
Terrain/Obstacle above or within 100’
below current aircraft altitude.
Yellow
Terrain/Obstacle between 100’ and
1000’ below current aircraft altitude.
Black
Terrain/Obstacle is more than 1000’
below aircraft altitude.
Flight
Planning
Red
GPS Nav
Terrain/Obstacle Location
AFCS
Color
Nav/Com/
XPDR/Audio
Turn the large FMS Knob to select the Map Page Group.
EAS
1)
Flight
Instruments
Display Terrain on the TERRAIN-SVS Page
Procedures
Enable/Disable Aviation Data
While the Terrain-SVS Page is displayed, press the MENU Key.
2)
Turn the small FMS Knob to select “Show (or Hide) Aviation Data”.
3)
Press the ENT Key.
Hazard
Avoidance
1)
Additional
Features
Terrain-SVS Inhibit
Abnormal
Operation
Inhibit Terrain
While the Terrain-SVS Page is displayed, select the INHIBIT Softkey.
Or:
1) Press the MENU Key.
2) Turn the small FMS Knob to select ‘Inhibit Terrain’.
3) Press the ENT Key.
Annun/
Alerts
Appendix
Index
190-01247-01 Rev. A
Garmin G1000 Cockpit Reference Guide for the Socata TBM 700
55
Hazard Avoidance
Nav/Com/
XPDR/Audio
EAS
Flight
Instruments
Enable Terrain
While the Terrain-SVS Page is displayed, select the INHIBIT Softkey.
Or:
1) While the Terrain-SVS Page is displayed, press the MENU Key.
2) Turn the small FMS Knob to select ‘Enable Terrain’.
3) Press the ENT Key.
GPS Nav
AFCS
NOTE: If Terrain-SVS alerts are inhibited when the Final Approach Fix is the
active waypoint in a GPS SBAS approach, a LOW ALT annunciation may appear
on the PFD next to the altimeter if the current aircraft altitude is at least 164
feet below the prescribed altitude at the Final Approach Fix.
Flight
Planning
TERRAIN AWARENESS & WARNING SYSTEM (TAWS) DISPLAY
Procedures
WARNING: The TAWS display shows supplemental information only. It should
not be used for navigation.
Hazard
Avoidance
NOTE: Terrain data is not displayed when the aircraft latitude is greater than
75 degrees north or 60 degrees south.
Additional
Features
NOTE: TAWS operation is only available when the G1000 is configured for a
TAWS-B installation.
Annun/
Alerts
Abnormal
Operation
Manual System Test
1)
While the TAWS-B Page is displayed, press the MENU Key.
2)
Turn the small FMS Knob to select ‘Test TAWS’.
3)
Press the ENT Key. During the test ‘TAWS TEST’ is displayed in the center
of the TAWS-B Page.
Appendix
When all is in working order, “TAWS System Test, OK” is heard.
Index
Display Terrain on the TAWS-B Page
56
1)
Turn the large FMS Knob to select the Map Page Group.
2)
Turn the small FMS Knob to select the TAWS-B Page.
Garmin G1000 Cockpit Reference Guide for the Socata TBM 700
190-01247-01 Rev. A
Hazard Avoidance
4)
Rotate the Joystick clockwise to display a larger area or rotate counterclockwise to display a smaller area.
Terrain/Obstacle above or within 100’
below current aircraft altitude.
Yellow
Terrain/Obstacle between 100’ and
1000’ below current aircraft altitude.
Black
Terrain/Obstacle is more than 1000’
below aircraft altitude.
GPS Nav
Red
AFCS
Terrain/Obstacle Location
Nav/Com/
XPDR/Audio
Color
EAS
If desired, select the VIEW Softkey to access the ARC and 360 softkeys.
When the ARC Softkey is selected, a radar-like 120° view is displayed.
Select the 360 Softkey to return to the 360° default display.
Flight
Instruments
3)
Enable/Disable Aviation Data
2)
Turn the small FMS Knob to select “Show (or Hide) Aviation Data”.
3)
Press the ENT Key.
Procedures
While the TAWS-B Page is displayed, press the MENU Key.
Flight
Planning
1)
TAWS Inhibit
Additional
Features
Abnormal
Operation
Inhibit TAWS
While the TAWS-B Page is displayed, select the INHIBIT Softkey.
Or:
1) Press the MENU Key.
2) Turn the small FMS Knob to select ‘Inhibit TAWS’.
3) Press the ENT Key.
Hazard
Avoidance
NOTE: If TAWS alerts are inhibited when the Final Approach Fix is the active
waypoint in a GPS SBAS approach, a LOW ALT annunciation may appear on
the PFD next to the altimeter if the current aircraft altitude is at least 164
feet below the prescribed altitude at the Final Approach Fix.
Annun/
Alerts
Appendix
Index
190-01247-01 Rev. A
Garmin G1000 Cockpit Reference Guide for the Socata TBM 700
57
Hazard Avoidance
PROFILE VIEW TERRAIN AND OBSTACLES
The system offers a Profile View of terrain and obstacles relative to the aircraft’s
current flight path and altitude on the Navigation Map Page of the MFD. Profile View
does not provide terrain or obstacle caution or warning annunciations or voice alerts,
nor does it display potential impact points inside the Profile View.
Enabling/Disabling Profile View
Procedures
Flight
Planning
GPS Nav
AFCS
Nav/Com/
XPDR/Audio
EAS
Flight
Instruments
Enable TAWS
While the TAWS-B Page is displayed, select the INHIBIT Softkey.
Or:
1) While the TAWS-B Page is displayed, press the MENU Key.
2) Turn the small FMS Knob to select ‘Enable TAWS’.
3) Press the ENT Key.
1)
On the Navigation Map Page, press the MENU Key.
2)
Select ‘Show Profile View’ or ‘Hide Profile View’ (choice dependent on
current state) and press the ENT Key.
Hazard
Avoidance
Enabling/Disabling Terrain on the Profile View
1)
Select the Navigation Map Page.
2)
Select the MAP Softkey.
Additional
Features
3) Select the TERRAIN Softkey.
Appendix
Annun/
Alerts
Abnormal
Operation
Customizing the Profile Path display on the Navigation Map Page
1)
Select the Navigation Map Page.
2)
Press the MENU Key.
3)
With ‘Map Setup’ highlighted, press the ENT Key.
4)
Turn the small FMS Knob to select the ‘Profile’ Group and press the ENT
Key.
5)
Turn the large FMS Knob or press the ENT Key to scroll through product
selections.
Index
• PROFILE PATH – Turns the display of the Profile Path on or off and sets
maximum map range at which the Profile Path is shown
58
Garmin G1000 Cockpit Reference Guide for the Socata TBM 700
190-01247-01 Rev. A
Hazard Avoidance
7)
8)
Press the ENT Key to select an option.
Press the FMS Knob or CLR Key to return to the Navigation Map Page with
the changed settings.
EAS
Turn the small FMS Knob to scroll through options (ON/OFF, range settings).
Flight
Instruments
6)
AIRBORNE COLOR WEATHER RADAR
Nav/Com/
XPDR/Audio
WARNING: Begin transmitting only when it is safe to do so. If it is desired to
transmit while the aircraft is on the ground, no personnel or objects should
be within 11 feet of the antenna.
AFCS
Flight
Planning
Displaying Weather on the Weather Radar Page
Turn the large FMS Knob to select the Map Page Group.
2)
Turn the small FMS Knob to select the Weather Radar Page.
3)
Select the MODE Softkey.
4)
If the aircraft is on the ground, select the STANDBY Softkey to initiate the
one minute warm-up period. After the warm-up is complete, the radar will
enter the Standby Mode. After the aircraft is airborne, select the WEATHER
Softkey.
Procedures
1)
If desired, select the VERTICAL Softkey for vertical scanning.
Annun/
Alerts
6)
Abnormal
Operation
Turn the Joystick to select the desired range.
2)
Select the MAP Softkey.
3)
Select the WX RADAR Softkey.
190-01247-01 Rev. A
Garmin G1000 Cockpit Reference Guide for the Socata TBM 700
Index
Select the Navigation Map Page.
Appendix
Enabling/Disabling Weather Radar on the Navigation Map Page
1)
Additional
Features
If the aircraft is already airborne, select the WEATHER or GROUND
Softkey. The one-minute warm-up period will be initiated, after which the
radar will begin transmitting. The horizontal scan is initially displayed.
Hazard
Avoidance
Or:
5)
GPS Nav
CAUTION: In Standby Mode, the antenna is parked at the center line. It
is always a good idea to put the radar in Standby Mode before taxiing the
aircraft to prevent the antenna from bouncing on the bottom stop and possibly
causing damage to the radar assembly.
59
Hazard Avoidance
AFCS
Nav/Com/
XPDR/Audio
EAS
Flight
Instruments
Or:
1)
On the Navigation Map Page, press the MENU Key.
2)
With ‘Map Setup’ highlighted, press the ENT Key.
3)
Turn the small FMS Knob to select the ‘Weather’ group, then press the ENT
Key.
4)
Turn the large FMS Knob to scroll through the product selections and
highlight the WX RADAR overlay selection (‘On’ or ‘Off’). Turn the small
FMS knob to highlight the desired selection.
5)
To remove the menu, press the FMS Knob or CLR Key.
Annun/
Alerts
Abnormal
Operation
Additional
Features
Hazard
Avoidance
Procedures
Flight
Planning
GPS Nav
Adjusting Antenna Tilt
Move the Joystick up or down to adjust the tilt of the antenna up or down.
Monitor the displayed tilt value in the TILT field.
When scanning vertically, a Tilt Line may be displayed to aid in positioning the tilt
of the antenna. If the Tilt Line is not displayed, perform the following steps:
1) Press the MENU Key
2) Turn the large FMS Knob to select ‘Show Tilt Line’.
3) Press the ENT Key.
Adjusting Antenna Bearing
Move the Joystick right or left to adjust the azimuth position of the antenna right
or left. Monitor the displayed bearing value in the BEARING field.
When scanning horizontally, a Bearing Line may be displayed to aid in positioning
the antenna for the vertical scan. If the Bearing Line is not displayed, perform the
following steps:
1) Press the MENU Key
2) Turn the large FMS Knob to select ‘Show Bearing Line’.
3) Press the ENT Key.
Appendix
Vertically Scan a Storm Cell
1) While in the Horizontal Scan view, move the Joystick to place the Bearing
Line on the desired storm cell, or other area, to be vertically scanned.
Index
2)
60
Select the VERTICAL Softkey. A vertical ‘slice’ of the selected area will now
be displayed.
Garmin G1000 Cockpit Reference Guide for the Socata TBM 700
190-01247-01 Rev. A
Hazard Avoidance
4)
Turn the Joystick to adjust the range.
5)
To select a new area to be vertically scanned, select the HORIZON Softkey
to return to the Horizontal Scan view and repeat the previous steps.
Select the GAIN Softkey to activate the cursor in the ‘GAIN’ field.
2)
Turn the small FMS Knob to adjust the gain for the desirable level. The
gain setting is visible in the gain field as a movable horizontal bar in
a flashing box. The line pointer is a reference depicting the calibrated
position.
3)
Press the FMS Knob to remove the cursor.
4)
Select the GAIN Softkey again to recalibrate the gain. ‘CALIBRATED’ will be
displayed in the ‘GAIN’ field.
GPS Nav
1)
AFCS
WARNING: Changing the gain in Weather Mode will cause precipitation
intensity to be displayed as a color not representative of the true intensity.
Remember to return the gain setting to ‘Calibrated’ for viewing the actual
intensity of precipitation.
Nav/Com/
XPDR/Audio
Adjusting Gain
EAS
Move the Joystick right or left to move the scanned “slice” a few degrees
right or left.
Flight
Instruments
3)
Flight
Planning
Procedures
Hazard
Avoidance
Ground Mapping
Press the MODE Softkey.
2)
Press the GROUND Softkey to place the radar in Ground Map Mode.
3)
Press the BACK Softkey.
4)
Press the FMS Knob to activate the cursor.
5)
Turn the large FMS Knob to place the cursor in the ‘TILT’ field.
6)
Adjust the antenna tilt angle by turning the small FMS Knob to position the
ground returns as desired.
7)
Press the FMS Knob to remove the cursor.
Additional
Features
1)
Abnormal
Operation
Annun/
Alerts
Appendix
Index
190-01247-01 Rev. A
Garmin G1000 Cockpit Reference Guide for the Socata TBM 700
61
Hazard Avoidance
AFCS
Nav/Com/
XPDR/Audio
EAS
Flight
Instruments
Sector Scan
2)
Press the FMS Knob to display the cursor.
3)
Turn the large FMS Knob to place the cursor in the SECTOR SCAN field.
4)
Turn the small FMS Knob to select the desired scan range setting.
5)
If desired, readjust the Bearing Line with the Joystick to change the center
of the Sector Scan.
6)
Press the FMS Knob to remove the cursor.
GPS Nav
Antenna Stabilization
Flight
Planning
Procedures
Hazard
Avoidance
Additional
Features
Abnormal
Operation
While in the Horizontal Scan Mode, move the Joystick right or left to place
the Bearing Line in the desired position. The location of the Bearing Line
will become the center point of the Sector Scan.
1)
To activate or deactivate the antenna stabilization, select the MODE
Softkey.
2)
Select the STAB ON Softkey to activate antenna stabilization or select
the STAB OFF Softkey to deactivate. The current stabilization condition is
shown in the upper right of the weather radar display.
Weather Attenuated Color Highlight (WATCH®)
To activate or deactivate the WATCH® feature, select the WATCH Softkey. This
feature is only available in the Horizontal Scan Mode.
Weather Alert
To activate or deactivate Weather Alert, select the WX ALRT Softkey. Activating
and deactivating will also enable or inhibit the alert on the PFD.
Automatic Standby
When the weather radar system is in the Weather or Ground Map Mode, upon
landing the system will automatically switch to Standby Mode.
Index
Appendix
Annun/
Alerts
1)
62
Garmin G1000 Cockpit Reference Guide for the Socata TBM 700
190-01247-01 Rev. A
Additional Features
Flight
Instruments
ADDITIONAL FEATURES
SYNTHETIC VISION
EAS
Nav/Com/
XPDR/Audio
WARNING: Use appropriate primary systems for navigation, and for terrain,
obstacle, and traffic avoidance. SVS is intended as an aid to situational
awareness only and may not provide the accuracy and/or fidelity upon which
to solely base decisions and/or plan maneuvers to avoid terrain, obstacles, or
traffic.
AFCS
Hazard
Avoidance
Additional
Features
Abnormal
Operation
Displaying Synthetic Terrain
2)
Press the SYN VIS Softkey.
3)
Press the SYN TERR Softkey.
4)
Press the BACK Softkey to return to the previous page.
Appendix
Press the PFD Softkey.
Annun/
Alerts
1)
Procedures
Pathways
Flight Path Marker
Horizon Heading Marks
Terrain and Obstacle Alerting
Three-dimensional Traffic
Airport Signs
Runway Display
Flight
Planning
•
•
•
•
•
•
•
GPS Nav
Synthetic Vision System (SVS) functionality is offered as an optional enhancement
to the G1000 Integrated Flight Deck System.
SVS is primarily comprised of a computer-generated forward-looking, attitude
aligned view of the topography immediately in front of the aircraft from the pilot’s
perspective. SVS information is shown on the primary flight display (PFD).
SVS offers a three-dimensional view of terrain and obstacles. Terrain and
obstacles that pose a threat to the aircraft in flight are shaded yellow or red.
In addition to SVS enhancement to the PFD, the following feature enhancements
have been added to the PFD:
Index
190-01247-01 Rev. A
Garmin G1000 Cockpit Reference Guide for the Socata TBM 700
63
Additional Features
Nav/Com/
XPDR/Audio
EAS
Flight
Instruments
Displaying Pathways
2)
Press the SYN VIS Softkey.
3)
If not already enabled, press the SYN TERR Softkey.
4)
Press the PATHWAY Softkey.
5)
Press the BACK Softkey to return to the previous page.
AFCS
GPS Nav
Flight
Planning
1)
Press the PFD Softkey.
2)
Press the SYN VIS Softkey.
3)
If not already enabled, press the SYN TERR Softkey.
4)
Press the HRZN HDG Softkey.
5)
Press the BACK Softkey to return to the previous page.
Procedures
Displaying Airport Signs
Hazard
Avoidance
Additional
Features
Press the PFD Softkey.
Displaying Heading on the Horizon
1)
Press the PFD Softkey.
2)
Press the SYN VIS Softkey.
3)
If not already enabled, press the SYN TERR Softkey.
4)
Press the APTSIGNS Softkey.
5)
Press the BACK Softkey to return to the previous page.
TERMINAL PROCEDURE CHARTS
NOTE: With the availability of SafeTaxi®, ChartView, or FliteCharts®, it may
be necessary to carry another source of charts on-board the aircraft.
Abnormal
Operation
Annun/
Alerts
Appendix
Index
1)
SafeTaxi®
SafeTaxi® is an enhanced feature that gives greater map detail as the map range
is adjusted in on the airport. The airport display on the map reveals runways with
numbers, taxiways identifiers, and airport landmarks including ramps, buildings,
control towers, and other prominent features. Resolution is greater at lower map
ranges. The aircraft symbol provides situational awareness while taxiing.
64
Garmin G1000 Cockpit Reference Guide for the Socata TBM 700
190-01247-01 Rev. A
Additional Features
Abnormal
Operation
Annun/
Alerts
Select the DP, STAR, APR, WX, and NOTAM softkeys to access charts for
departures, arrivals, approaches, weather and NOTAMs. Note that NOTAMS
are only available with ChartView.
3)
Select the GO BACK Softkey to return to the previous page.
65
Index
2)
Appendix
Move the map pointer to point to a desired point on the map and select the
SHW CHRT Softkey.
Garmin G1000 Cockpit Reference Guide for the Socata TBM 700
Additional
Features
Or:
190-01247-01 Rev. A
Hazard
Avoidance
Select the SHW CHRT Softkey when displayed.
Procedures
1)
Flight
Planning
View Charts from the Navigation Map Page
GPS Nav
FliteCharts® resemble the paper version of AeroNav Services terminal procedures
charts. The charts are displayed with high-resolution and in color for applicable
charts. Current aircraft position is not displayed on FliteCharts.
The FliteCharts database contains procedure charts for the United States only.
This database is updated on a 28-day cycle. If not updated within 180 days of the
expiration date, FliteCharts will no longer function.
AFCS
FliteCharts®
Nav/Com/
XPDR/Audio
ChartView resembles the paper version of Jeppesen terminal procedures charts.
The charts are displayed in full color with high-resolution. The MFD depiction shows
the aircraft position on the moving map in the plan view of most approach charts and
on airport diagrams.
The ChartView database is updated on a 14-day cycle. If the ChartView database
is not updated within 70 days of the expiration date, ChartView will no longer
function.
EAS
ChartView
Flight
Instruments
Pressing the DCLTR Softkey (declutter) once removes the taxiway markings and
airport identification labels. Pressing the DCLTR Softkey twice removes VOR station
ID, the VOR symbol, and intersection names if within the airport plan view. Pressing
the DCLTR Softkey a third time removes the airport runway layout, unless the airport
in view is part of an active route structure. Pressing the DCLTR Softkey again cycles
back to the original map detail.
The SafeTaxi database contains detailed airport diagrams for selected airports.
These diagrams provide the pilot with situational awareness by displaying the aircraft
position in relation to taxiways, ramps, runways, terminals, and services. This
information should not be used by the pilot as the basis for maneuvering the aircraft
on the ground. This database is updated on a 56-day cycle.
Additional Features
Nav/Com/
XPDR/Audio
EAS
Flight
Instruments
View Charts from the Active Flight Plan Page
1)
While viewing the Active Flight Plan Page, press the FMS Knob to activate
the cursor.
2)
Turn the large FMS Knob to select the departure airport, destination
airport, departure, arrival, or approach.
3)
Select the SHW CHRT Softkey. The appropriate chart is displayed, if
available for the item selected.
4)
Select the GO BACK Softkey to return to the previous page.
While viewing a chart press the MENU Key to display the Page Menu
OPTIONS.
2)
Turn the large FMS Knob to highlight the ‘Chart Setup’ Menu Option and
press the ENT Key.
3)
Turn the large FMS Knob to move between the ‘FULL SCREEN’ and ‘COLOR
SCHEME’ Options.
4)
Turn the small FMS Knob to choose between the ‘On’ and ‘Off’ Full Screen
Options.
5)
Turn the small FMS Knob to choose between ‘Day’, ‘Auto’, and ‘Night’
Options.
6)
In Auto Mode, turn the large FMS Knob to select the percentage field and
change percentage with the small FMS Knob. The percentage of change is
the day/night crossover point based on backlighting intensity.
7)
Press the FMS Knob when finished to remove the Chart Setup Menu.
AOPA AIRPORT DIRECTORY
AOPA Airport Directory adds enhanced airport information when viewing airports
on the WPT-Airport Information Page.
This database is updated four times per year. Check fly.garmin.com for the current
database.
View Airport Directory Information
While viewing the WPT-Airport Information Page, if necessary, select the
INFO-1 Softkey to change the softkey label to display INFO-2. AOPA
airport information is displayed on the right half of the display.
Index
Appendix
Abnormal
Operation
1)
Annun/
Alerts
Additional
Features
Hazard
Avoidance
Procedures
Flight
Planning
GPS Nav
AFCS
Change Day/Night View
66
Garmin G1000 Cockpit Reference Guide for the Socata TBM 700
190-01247-01 Rev. A
Additional Features
The XM Radio Page provides information and control of the audio entertainment
features of the SiriusXM Satellite Radio.
2)
Turn the small FMS Knob to select SiriusXM Radio.
3)
Select the RADIO Softkey to show the XM Radio Page where audio
entertainment is controlled.
AFCS
Turn the large FMS Knob to select the Auxiliary Page Group.
Nav/Com/
XPDR/Audio
1)
EAS
Selecting the XM Radio Page
Flight
Instruments
SIRIUSXM® SATELLITE RADIO ENTERTAINMENT
Active Channel and Channel List
Flight
Planning
Selecting a Category
Additional
Features
Abnormal
Operation
While on the XM Radio Page, select the CHNL Softkey.
2)
Select the CH + Softkey to go down through the list in the Channel Box, or
move up the list with the CH – Softkey.
Appendix
Or:
Annun/
Alerts
1)
Press the FMS Knob to highlight the channel list and turn the large FMS
Knob to scroll through the channels.
Index
With the desired channel highlighted, press the ENT Key.
Garmin G1000 Cockpit Reference Guide for the Socata TBM 700
Hazard
Avoidance
Select an Available Channel within the Selected Category
190-01247-01 Rev. A
Procedures
The Category Box of the XM Radio Page displays the currently selected category
of audio.
1) Select the CATGRY Softkey on the XM Radio Page.
2) Select the CAT + and CAT - softkeys to cycle through the categories.
Or:
Turn the small FMS Knob to display the ‘Categories’ list. Highlight the
desired category with the small FMS Knob.
3) Press the ENT Key.
3)
GPS Nav
The Active Channel Box on the XM Radio Page displays the currently selected
channel. The Channels List Box of the XM Radio Page shows a list of the available
channels for the selected category.
67
Additional Features
1)
While on the XM Radio Page, select the CHNL Softkey.
2)
Select the DIR CH Softkey. The channel number in the Active Channel Box
is highlighted.
3)
Select the numbered softkeys located on the bottom of the display to
directly select the desired channel number.
4)
Press the ENT Key to activate the selected channel.
Nav/Com/
XPDR/Audio
EAS
Flight
Instruments
Entering a Channel Directly
AFCS
Assigning Channel Presets
Procedures
Flight
Planning
GPS Nav
Up to 15 channels from any category can be assigned a preset number.
1) On the XM Radio Page, with the desired channel active, select the
PRESETS Softkey to access the first five preset channels (PS1 - PS5).
2) Select the MORE Softkey to access the next five channels (PS6 – PS10),
and again to access the last five channels (PS11 – PS15). Selecting the
MORE Softkey repeatedly cycles through the preset channels.
3) Select the SET Softkey.
4) Select any one of the (PS1 - PS15) softkeys to assign a number to the
active channel.
Abnormal
Operation
Additional
Features
Hazard
Avoidance
Adjusting Volume
1)
With the XM Radio Page displayed, select the VOL Softkey.
2)
Select the VOL – Softkey to reduce volume or select the VOL + Softkey to
increase volume. (Once the VOL Softkey is selected, the volume can also be
adjusted using the small FMS Knob.)
3)
Select the MUTE Softkey to mute the audio. Select the MUTE Softkey
again to unmute the audio.
Index
Appendix
Annun/
Alerts
SiriusXM Radio volume may also be adjusted on each passenger headset.
68
Garmin G1000 Cockpit Reference Guide for the Socata TBM 700
190-01247-01 Rev. A
Additional Features
EAS
Operation of these features in the cockpit is accomplished through the AUXTELEPHONE, AUX-TEXT MESSAGING, AUX-REPORT STATUS, and AUX-WI-FI
SETUP Pages.
Flight
Instruments
SATELLITE TELEPHONE & SMS MESSAGING SERVICE
Registering System With Garmin
Nav/Com/
XPDR/Audio
AFCS
A subscriber account must be established prior to using the Iridium Satellite
System. Before setting up an Iridium account, obtain the serial number of the Iridium
Transceiver (GSR1) and the System ID by viewing the AUX- SYSTEM STATUS Page.
Contact Garmin at 1-866-739-5687 in the United States or 913-397-8200, ext. 1135.
Disable/Enable Iridium Transceiver
GPS Nav
Iridium telephone may be turned on or off by performing the following steps.
Flight
Planning
To enable the Iridium telephone system:
With the AUX-TELEPHONE Page displayed, select the MENU Key on the
MFD to display the Page Menu.
2)
Turn either FMS Knob to place the cursor on ‘Enable Iridium Transmission’.
3)
Press the ENT Key.
Hazard
Avoidance
To disable the Iridium telephone system:
2)
Turn either FMS Knob to place the cursor on ‘Disable Iridium Transmission’.
3)
Press the ENT Key.
Abnormal
Operation
With the AUX-TELEPHONE Page displayed, select the MENU Key on the
MFD to display the Page Menu.
Telephone Communication
Turn the small FMS Knob to select the AUX-TELEPHONE Page.
190-01247-01 Rev. A
Garmin G1000 Cockpit Reference Guide for the Socata TBM 700
Index
2)
Appendix
To view the Telephone Page:
Annun/
Alerts
The pilot or copilot can place and answer calls on the Iridium satellite network.
Control and monitoring of telephone functions are accomplished through the AUXTELEPHONE Page.
Turn the large FMS Knob on the MFD to select the AUX page group.
Additional
Features
1)
1)
Procedures
1)
69
Additional Features
Flight
Instruments
Internal
Phone
External
Phone
Description
EAS
Phone is Idle
Nav/Com/
XPDR/Audio
Phone is ringing
AFCS
Phone has a dial tone (off hook) or connected to
another phone
GPS Nav
Phone dialed is busy
Flight
Planning
Phone is dialing another phone
Procedures
Phone has failed
Hazard
Avoidance
Phone status not known
Abnormal
Operation
Additional
Features
Phone is disabled
Annun/
Alerts
Phone is reserved for data transmission
Appendix
Calling other phone or incoming call from other phone
Index
Other phone is on hold
Phones are connected
70
Garmin G1000 Cockpit Reference Guide for the Socata TBM 700
190-01247-01 Rev. A
Additional Features
Press the TEL Key on the audio panel.
2)
Select the ANSWER Softkey on the MFD.
Nav/Com/
XPDR/Audio
1)
EAS
Answering an incoming call:
Flight
Instruments
Incoming Calls
When viewing MFD pages other than the AUX-TELEPHONE Page, a pop-up alert
will be displayed, accompanied by a ringtone heard on the selected cockpit audio. The
pop-up alert may be inhibited at times, such as during takeoff. In addition to the popup alert, a ringing phone symbol will be displayed to the right of the MFD page title.
AFCS
Or:
While viewing the AUX-TELEPHONE Page:
Press the MENU Key to display the Page Menu.
3)
Turn either FMS Knob to place the cursor on ‘Answer Incoming Call’.
4)
Press the ENT Key.
With the AUX-TELEPHONE Page displayed, press the MENU Key on the
MFD to display the Page Menu.
2)
Turn either FMS Knob to place the cursor on ‘Disable Incoming Call Alerts’.
3)
Press the ENT Key. The voice and pop-up alert will not be displayed now
when an incoming call is received.
Annun/
Alerts
1)
Abnormal
Operation
Disabling incoming call alerts:
Additional
Features
Selecting the IGNORE Softkey will extinguish the pop-up window and leave the
current call unanswered. Selecting the IGNRE ALL Softkey will extinguish the popup window for the current and all future incoming calls and leave the current call
unanswered. Selecting the TEL Softkey will display the AUX-TELEPHONE Page allowing additional call information to be viewed before answering.
Hazard
Avoidance
2)
Procedures
Press the TEL Key on the audio panel.
Flight
Planning
1)
GPS Nav
NOTE: The Push-to-Talk switch is not utilized for telephone communication.
The microphone is active after selecting the ANSWER Softkey, and stays active
until the call is terminated.
Appendix
Index
190-01247-01 Rev. A
Garmin G1000 Cockpit Reference Guide for the Socata TBM 700
71
Additional Features
Flight
Instruments
Outgoing Calls
Voice calls can be made from the cockpit through the Iridium Satellite Network.
Nav/Com/
XPDR/Audio
EAS
To make a call:
1)
Press the TEL Key on the audio panel.
2)
Select the DIAL Softkey on the MFD.
Or:
While viewing the AUX-TELEPHONE Page:
AFCS
a) Press the TEL Key on the audio panel.
b) Press the MENU Key to display the Page Menu.
GPS Nav
c) Turn either FMS Knob to place the cursor on ‘Dial a Phone Call’.
d) Press the ENT Key.
Index
Appendix
Annun/
Alerts
Abnormal
Operation
Additional
Features
Hazard
Avoidance
Procedures
Flight
Planning
3)
Selecting the number softkeys on the MFD, enter 00 + country code +
area code + phone number when calling a non-satellite telephone system.
Enter 00 + Satellite Country Code (shown in the following table) + phone
number when placing a call to another satellite telephone system.
Satellite System
Inmarsat
ICO
Country Code
870
Ellipso
Iridium
Globalstar
8812 or 8813
8816 or 8817
8818 or 8819
8810 or 8811
4)
Press the ENT Key. ‘OK’ is highlighted.
5)
Press the ENT Key. The system will begin calling the number.
When the phone is answered, the connection is established. To exit the call, select
the HANGUP Softkey.
Text Messaging (SMS)
Messages may be sent to an email address or text message capable cellular telephone.
Message length is limited to 160 characters, including the email address.
The text messaging user interface is mainly through the AUX-TEXT MESSAGING
Page.
72
Garmin G1000 Cockpit Reference Guide for the Socata TBM 700
190-01247-01 Rev. A
Additional Features
Turn the large FMS Knob on the MFD to select the AUX page group.
2)
Turn the small FMS Knob to select SATELLITE PHONE.
3)
If necessary, press the SMS Softkey to display the AUX-TEXT MESSAGING
Page.
Nav/Com/
XPDR/Audio
Message Symbol
EAS
1)
Flight
Instruments
Viewing the Text Messaging Page
Description
AFCS
Received text message that has not been opened
GPS Nav
Received text message that has been opened
Flight
Planning
Saved text message, draft not sent
Procedures
System is sending text message
Hazard
Avoidance
Text message has been sent
Additional
Features
System failed to send text message
73
Index
Garmin G1000 Cockpit Reference Guide for the Socata TBM 700
Appendix
190-01247-01 Rev. A
Annun/
Alerts
Viewing a Text Message When Received
When viewing MFD pages other than the AUX-TEXT MESSAGING Page, a pop-up
alert will be displayed when a new text message is received.
Press the VIEW Softkey to view the message. Pressing the IGNORE Softkey will
extinguish the pop-up window and leave the text message unopened. Pressing the
IGNR ALL Softkey will extinguish the pop-window and ignore all future incoming
text messages. Pressing the SMS Softkey will display the AUX-TEXT MESSAGING
Page.
The pop-up alerts may be enabled or disabled through the Page Menu.
Abnormal
Operation
Predefined text message
Additional Features
Nav/Com/
XPDR/Audio
EAS
Flight
Instruments
Enable/Disable Incoming Text Message Pop-Up Alerts
1)
With the AUX-TEXT MESSAGING Page displayed, press the MENU Key on
the MFD to display the Page Menu.
2)
Turn either FMS Knob to place the cursor on ‘Disable New Message
Popups’ or ‘Enable New Message Popups’.
3)
Press the ENT Key. The pop-up alert will not be displayed when an
incoming text message is received.
AFCS
Reply to a Text Message
While viewing the text message, press the REPLY Softkey.
GPS Nav
Or:
a) Press the MENU Key to display the Page Menu.
b) Turn either FMS Knob to place the cursor on ‘Reply To Message’.
Flight
Planning
c) Press the ENT Key.
Procedures
Sending a Text Message
1)
While viewing the AUX-TEXT MESSAGING Page, press the NEW Softkey.
Or:
Hazard
Avoidance
a) Press the MENU Key to display the Page Menu.
b) Turn either FMS Knob to place the cursor on ‘Draft New Message’.
2)
The TEXT MESSAGE DRAFT Window is now displayed with the cursor in
the ‘TO’ field. Enter the desired telephone number or email address. Entry
can be accomplished through the alphanumeric keys on the controller, or
combination of the FMS Knob on the controller and softkeys on the MFD.
The FMS Knob is used to enter letters and numbers, or numbers can be
entered from the MFD by pressing the NUMBERS Softkey. Press the CAP
LOCK Softkey to create upper and lower case alpha characters. Special
characters can be accessed by pressing the SYMBOLS Softkey.
3)
Press the ENT Key. The cursor is now displayed in the ‘MESSAGE’ field.
4)
Enter the desired message using any combination of entry methods as
described in step 2.
Index
Appendix
Annun/
Alerts
Abnormal
Operation
Additional
Features
c) Press the ENT Key.
74
Garmin G1000 Cockpit Reference Guide for the Socata TBM 700
190-01247-01 Rev. A
Additional Features
Press the ENT Key.
6)
Press the SEND Softkey to send the message immediately, or press the
SAVE Softkey to save the message in Outbox for sending at a later time.
Press the CANCEL Softkey to delete the message.
Flight
Instruments
5)
Turn either FMS Knob to select ‘Edit Predefined Messages’.
3)
Press the ENT Key. The PREDEFINED MESSSAGES view is now displayed.
4)
Press the NEW Softkey.
Flight
Planning
2)
GPS Nav
While viewing the AUX-TEXT MESSAGING Page, press the MENU Key to
display the Page Menu.
AFCS
1)
Or:
Procedures
a) Press the MENU Key to display the Page Menu.
b) Turn either FMS Knob to place the cursor on ‘Draft New Predefined
Message’.
Hazard
Avoidance
c) Press the ENT Key. The PREDEFINED SMS TEXT MESSAGE Window is
now displayed.
Press the ENT Key. The cursor is now displayed in the ‘MESSAGE’ field.
7)
Enter the desired message using any combination of entry methods as
described in step 5.
8)
Press the ENT Key.
9)
Press the SAVE Softkey. The new predefined message is now shown in
the displayed list. Pressing the CANCEL Softkey will delete the message
without saving.
Appendix
Index
Garmin G1000 Cockpit Reference Guide for the Socata TBM 700
Annun/
Alerts
6)
Abnormal
Operation
The cursor is displayed in the ‘TITLE’ field. Enter the desired message title.
Entry can be accomplished through the alphanumeric keys on the controller,
or combination of the FMS Knob on the controller and softkeys on the MFD.
The FMS Knob is used to enter letters and numbers, or numbers can be
entered from the MFD by pressing the NUMBERS Softkey. Press the CAP
LOCK Softkey to create upper and lower case alpha characters. Special
characters can be accessed by pressing the SYMBOLS Softkey.
Additional
Features
5)
190-01247-01 Rev. A
Nav/Com/
XPDR/Audio
Create a Predefined Text Message
EAS
Predefined Text Messages
Time and effort can be saved in typing text messages that are used repeatedly by
saving these messages as a predefined message.
75
Additional Features
Flight
Instruments
10) Press the MENU Key to display the Page Menu.
11) Turn either FMS Knob to place the cursor on ‘Stop Editing Predefined
Message’.
EAS
12) Press the ENT Key.
1)
While viewing the AUX-TEXT MESSAGING Page, press the NEW Softkey.
2)
The TEXT MESSAGE DRAFT Window is now displayed with the cursor in
the ‘TO’ field. Enter the desired telephone number or email address. Entry
can be accomplished through the alphanumeric keys on the controller, or
combination of the FMS Knob on the controller and softkeys on the MFD.
The FMS Knob is used to enter letters and numbers, or numbers can be
entered from the MFD by pressing the NUMBERS Softkey. Press the CAP
LOCK Softkey to create upper and lower case alpha characters. Special
characters can be accessed by pressing the SYMBOLS Softkey.
3)
Press the ENT Key. The cursor is now displayed in the ‘MESSAGE’ field.
4)
Press the PREDEFD Softkey. The PREDEFINED MESSAGE MENU Window is
displayed.
6)
Press the ENT Key. The predefined message text is inserted into the
message field. If desired, the message can be edited by using the FMS
Knobs.
7)
Press the ENT Key.
8)
Press the SEND Softkey to transmit the message.
Text Message Boxes
Received text messages reside in the Inbox as ‘Read’ or ‘Unread’ messages. The
Outbox contains ‘Sent” and ‘Unsent’ text messages. Saved messages that are meant to
be sent later are stored as Drafts. Each text message box may be viewed separately, or
together in any combination.
Show Inbox Messages
Appendix
Annun/
Alerts
Abnormal
Operation
Additional
Features
Hazard
Avoidance
Procedures
Flight
Planning
GPS Nav
AFCS
Nav/Com/
XPDR/Audio
Send a Predefined Text Message
While viewing the AUX-TEXT MESSAGING Page, press the ARRANGE
Softkey, then press the INBOX Softkey.
Index
Or:
a) Press the MENU Key to display the Page Menu.
76
Garmin G1000 Cockpit Reference Guide for the Socata TBM 700
190-01247-01 Rev. A
Additional Features
Flight
Instruments
b) Turn either FMS Knob to place the cursor on ‘Show Inbox Messages’.
c) Press the ENT Key. The message box selected for viewing is indicated
at the bottom left of the list window.
EAS
Show Outbox Messages
Nav/Com/
XPDR/Audio
While viewing the AUX-TEXT MESSAGING Page, press the ARRANGE
Softkey, then press the OUTBOX Softkey.
Or:
a) Press the MENU Key to display the Page Menu.
GPS Nav
c) Press the ENT Key. The message box selected for viewing is indicated
at the bottom left of the list window.
AFCS
b) Turn either FMS Knob to place the cursor on ‘Show Outbox Messages’.
Show Draft Messages
Flight
Planning
While viewing the AUX-TEXT MESSAGING Page, press the ARRANGE
Softkey, then press the DRAFTS Softkey.
Procedures
Or:
a) Press the MENU Key to display the Page Menu.
Hazard
Avoidance
b) Turn either FMS Knob to place the cursor on ‘Show Draft Messages’.
c) Press the ENT Key. The message box selected for viewing is indicated
at the bottom left of the list window.
Additional
Features
Abnormal
Operation
Arranging Text Messages
The viewed messages may be listed according to the date/time the message was
sent or received, the type of message (read, unread, sent, unsent, etc.), or by message
address.
View Messages Sorted by Message Date/Time:
Annun/
Alerts
While viewing the AUX-TEXT MESSAGING Page, press the ARRANGE
Softkey, then press the TIME Softkey.
Appendix
Or:
a) Press the MENU Key to display the Page Menu.
Index
b) Turn either FMS Knob to place the cursor on ‘Sort By Date/Time’.
c) Press the ENT Key. The sorting selection is indicated at the bottom
center of the list window.
190-01247-01 Rev. A
Garmin G1000 Cockpit Reference Guide for the Socata TBM 700
77
Additional Features
Flight
Instruments
View Messages Sorted by Message Type
While viewing the AUX-TEXT MESSAGING Page, press the ARRANGE
Softkey, then press the TYPE Softkey.
EAS
Or:
a) Press the MENU Key to display the Page Menu.
Nav/Com/
XPDR/Audio
b) Turn either FMS Knob to place the cursor on ‘Sort By Type’.
AFCS
c) Press the ENT Key. The sorting selection is indicated at the bottom
center of the list window.
View Messages Sorted by Address:
GPS Nav
While viewing the AUX-TEXT MESSAGING Page, press the ARRANGE
Softkey, then press the ADDRESS Softkey.
Or:
Flight
Planning
a) Press the MENU Key to display the Page Menu.
b) Turn either FMS Knob to place the cursor on ‘Sort By Address’.
Procedures
c) Press the ENT Key. The sorting selection is indicated at the bottom
center of the list window.
Additional
Features
Hazard
Avoidance
Viewing The Content of a Text Message
1)
While viewing the AUX-TEXT MESSAGING Page, select the desired message box.
2)
Press the FMS Knob to activate the cursor.
3)
Turn either FMS Knob to select the desired message.
4)
Press the VIEW Softkey.
Abnormal
Operation
Or:
Press the ENT Key.
Annun/
Alerts
Or:
a) Press the MENU Key to display the Page Menu.
Appendix
b) Turn either FMS Knob to place the cursor on ‘View Selected Message’.
c) Press the ENT Key.
5)
To close the text message, press the CLOSE Softkey.
Index
Or:
78
Garmin G1000 Cockpit Reference Guide for the Socata TBM 700
190-01247-01 Rev. A
Additional Features
Flight
Instruments
a) Press the MENU Key to display the Page Menu.
b) Turn either FMS Knob to place the cursor on ‘Close Message’.
c) Press the ENT Key.
2)
Turn either FMS Knob to select the desired message.
3)
Press the MRK READ Softkey.
AFCS
While viewing the Inbox on the AUX-TEXT MESSAGING Page, press the
FMS Knob to activate the cursor.
Nav/Com/
XPDR/Audio
1)
EAS
Mark Selected Message As Read
Or:
GPS Nav
a) Press the MENU Key to display the Page Menu.
b) Turn either FMS Knob to place the cursor on ‘Mark Selected Message
As Read’.
Flight
Planning
c) Press the ENT Key.
The message symbol now indicates the message has been opened.
Turn either FMS Knob to place the cursor on ‘Mark All New Messages As
Read’.
3)
Press the ENT Key. A confirmation window is displayed.
4)
With cursor highlighting ‘YES’, press the ENT Key. The message symbols
now indicate all the message have been opened.
Abnormal
Operation
2)
Additional
Features
While viewing the Inbox on the AUX-TEXT MESSAGING Page, press the
MENU Key to display the Page Menu.
Hazard
Avoidance
1)
Procedures
Mark All Messages As Read
Delete a Message
2)
Turn either FMS Knob to select the desired message.
3)
Press the DELETE Softkey.
Appendix
While viewing the Inbox on the AUX-TEXT MESSAGING Page, press the
FMS Knob to activate the cursor.
Annun/
Alerts
1)
Or:
b) Turn either FMS Knob to place the cursor on ‘Delete Selected Message’.
c) Press the ENT Key.
190-01247-01 Rev. A
Garmin G1000 Cockpit Reference Guide for the Socata TBM 700
79
Index
a) Press the MENU Key to display the Page Menu.
MAINTENANCE LOGS
The system provides recording of CAS, CMC, exceedances, and other critical
aircraft data that occur while the aircraft is on the ground or in flight.
The Maintenance Logs feature is accessible by entering a password. No pilot action
is required.
Viewing the Maintenance Logs Page:
1) Turn the large FMS Knob on the MFD to select the AUX page group.
2) Turn the small FMS Knob to select ‘MAINTENANCE LOG’. The AUXMAINTENANCE LOGS Page is now displayed.
AUXILIARY VIDEO (OPTIONAL)
There are four modes of operation of the auxiliary video display: Full-Screen,
Full-Screen with Digital Zoom, Split-Screen with Map, and Split-Screen with Map and
Digital Zoom.
Flight
Planning
GPS Nav
AFCS
Nav/Com/
XPDR/Audio
EAS
Flight
Instruments
Additional Features
Procedures
Displaying auxiliary video:
1) Turn the large FMS Knob to select the AUX page group.
2) Turn the small FMS Knob to select VIDEO and display the AUX-VIDEO Page.
The video display softkeys shown below appear on the AUX - VIDEO Page.
Selecting video menu options:
1) While viewing the AUX - VIDEO Page press the MENU Key to display the
Page Menu OPTIONS.
2)
Turn the large FMS Knob to highlight the desired video adjustment option
and press the ENT Key.
Once the ENT key is pressed on any option, the page menu closes and returns to
the AUX - VIDEO Page.
Video Setup
Video brightness, contrast, and saturation may be adjusted be selecting the setup
function. While viewing the setup function softkeys, after 45 seconds of softkey
inactivity, the system reverts to the AUX VIDEO Page softkeys.
Index
Appendix
Annun/
Alerts
Abnormal
Operation
Additional
Features
Hazard
Avoidance
Control of the AUX - VIDEO Page can also be accessed through the Page Menu.
80
Garmin G1000 Cockpit Reference Guide for the Socata TBM 700
190-01247-01 Rev. A
Additional Features
EAS
Nav/Com/
XPDR/Audio
AFCS
GPS Nav
Display Selection
Appendix
Index
81
Annun/
Alerts
Garmin G1000 Cockpit Reference Guide for the Socata TBM 700
Abnormal
Operation
Pressing the VID ZM + or VID ZM - Softkeys increases or decreases video display
magnification between 1x and 10x.
The Joystick can be used to increase or decrease the range setting on the map
display or zoom in and out on the video display. While in the Split-Screen mode,
pressing the MAP ACTV or VID ACTV Softkey determines which display the Joystick
adjusts. Pressing the softkey to display MAP ACTV allows the Joystick to control the
range setting of the map display. Pressing the softkey to display VID ACTV allows the
Joystick to control the zoom setting of the video display.
When zooming in on the video display, a Zoom Window will appear in the upper
right of the display. A box within this window indicates the portion of the display
currently being viewed. The currently displayed portion of the full display may be
adjusted by using the Joystick.
Additional
Features
Zoom/Range
Hazard
Avoidance
While on the AUX - VIDEO Page, press the INPUT Softkey to select the video
source.
Procedures
Input Selection
Flight
Planning
Pressing the HIDE MAP Softkey removes the map and displays video on the full
screen. The softkey label changes to grey with black characters. Pressing the HIDE
MAP Softkey again restores the map view and the small video image. The softkey label
returns to white characters on a black background.
190-01247-01 Rev. A
Flight
Instruments
Adjusting the video settings:
1) With the AUX-VIDEO Page displayed, press the SETUP Softkey.
2) Press the BRIGHT - or BRIGHT +, to adjust display brightness in five
percent increments from 0 to 100%.
3) Press the CNTRST- or CNTRST +, to adjust display contrast in five
percent increments from 0 to 100%.
4) Press the SAT - or SAT +, to adjust display saturationin five percent
increments from 0 to 100%.
5) If desired, return the display to the default settings by pressing the RESET
Softkey.
6) Press the BACK Softkey to return to the previous softkey level.
SCHEDULER
The Scheduler feature can be used to enter and display reminder messages (e.g.,
Hot Section Inspection or Phase 1 Maintenance Check) in the Messages Window on
the PFD. Messages can be set to display based on a specific date and time (event), once
the message timer reaches zero (one-time; default setting), or recurrently whenever
the message timer reaches zero (periodic). Message timers set to periodic alerting
automatically reset to the original timer value once the message is displayed. When
power is cycled, all messages are retained until deleted, and message timer countdown
is resumed.
Entering a Scheduler Message
Hazard
Avoidance
Procedures
Flight
Planning
GPS Nav
AFCS
Nav/Com/
XPDR/Audio
EAS
Flight
Instruments
Additional Features
1)
Select the AUX - Utility Page.
2)
Press the FMS Knob momentarily to activate the flashing cursor.
3)
Turn the large FMS Knob to highlight the first empty scheduler message
naming field.
4)
Use the FMS Knob to enter the message text to be displayed in the
Messages Window and press the ENT Key.
5)
Press the ENT Key again or use the large FMS Knob to move the cursor to
the field next to Type.
6)
Turn the small FMS Knob to select the message type:
• Event—Message issued at the specified date/time
Additional
Features
• One-time—Message issued when the message timer reaches zero
(default setting)
Annun/
Alerts
Abnormal
Operation
• Periodic—Message issued each time the message timer reaches zero
7)
Press the ENT Key again or use the large FMS Knob to move the cursor to
the next field.
8)
For periodic and one-time message, use the FMS Knob to enter the timer
value (HH:MM:SS) from which to countdown and press the ENT Key.
9)
For event-based messages:
Appendix
a) Use the FMS Knob to enter the desired date (DD-MM-YY) and press
the ENT Key.
Index
b) Press the ENT Key again or use the large FMS Knob to move the cursor
to the next field.
c) Use the FMS Knob to enter the desired time (HH:MM) and press the
ENT Key.
82
Garmin G1000 Cockpit Reference Guide for the Socata TBM 700
190-01247-01 Rev. A
Additional Features
Deleting a Scheduler Message
EAS
1) Select the AUX - Utility Page.
3)
Turn the large FMS Knob to highlight the name field of the scheduler
message to be deleted.
4)
Press the CLR Key to clear the message text. If the CLR Key is pressed
again, the message is restored.
AFCS
Press the FMS Knob momentarily to activate the flashing cursor.
Nav/Com/
XPDR/Audio
2)
Flight
Instruments
10) Press the ENT Key again or use the large FMS Knob to move the cursor to
enter the next message.
5)
Abnormal
Operation
Press the FMS Knob momentarily to activate the flashing cursor.
Annun/
Alerts
3) Turn the large FMS Knob to highlight ‘CREATE’ in the Pilot Profile Box.
4)
Additional
Features
1) Use the FMS Knob to select the AUX - System Setup Page.
2)
Hazard
Avoidance
Creating a Profile
Procedures
When the system is powered on, the last selected pilot profile is shown on the MFD
power-up screen. The system can store up to 25 profiles; the currently active profile,
the amount of memory used, and the amount of memory available are shown at the
top of the AUX - System Setup Page in the box labeled ‘Pilot Profile’.
Flight
Planning
PILOT PROFILES
GPS Nav
Press the ENT Key while the message line is cleared to clear the message
text.
Scheduler messages appear in the Messages Window on the PFD. When a scheduler
message is waiting, the MSG Softkey label flashes. Selecting the MSG Softkey opens
the Messages Window and acknowledges the scheduler message. Selecting the MSG
Softkey again removes the Messages Window from the display, and the scheduler
message is deleted from the message queue.
Press the ENT Key. A ‘Create Profile’ window is displayed.
Appendix
5) Use the FMS Knob to enter a profile name up to 16 characters long and
press the ENT Key. Pilot profile names cannot begin with a blank as the
first letter.
Index
190-01247-01 Rev. A
Garmin G1000 Cockpit Reference Guide for the Socata TBM 700
83
EAS
Flight
Instruments
Additional Features
6)
In the next field, use the small FMS Knob to select the desired settings
upon which to base the new profile. Profiles can be created based on
Garmin factory defaults, default profile settings (initially based on Garmin
factory defaults unless edited by the pilot), or current system settings.
7)
Press the ENT Key.
Nav/Com/
XPDR/Audio
8) With ‘CREATE’ highlighted, press the ENT Key to create the profile.
Or:
AFCS
Use the large FMS Knob to select ‘CREATE and ACTIVATE’ and press the
ENT Key to activate the new profile.
GPS Nav
9)
To cancel the process, select ‘CANCEL’ with the large FMS Knob and press
the ENT Key.
10) Press the FMS Knob to deactivate the cursor.
Flight
Planning
Selecting an Active Profile
1) Use the FMS Knob to select the AUX - System Setup Page.
Procedures
2)
Press the FMS Knob momentarily to activate the flashing cursor.
3) Turn the large FMS Knob to highlight the active profile field in the Pilot
Profile Box.
Hazard
Avoidance
4) Turn the small FMS Knob to display the pilot profile list and highlight the
desired profile.
5) Press the ENT Key. The system loads and displays the system settings for
Additional
Features
the selected profile.
6)
Press the FMS Knob to deactivate the cursor.
Abnormal
Operation
Renaming a Profile
1) Use the FMS Knob to select the AUX - System Setup Page.
Annun/
Alerts
2)
Press the FMS Knob momentarily to activate the flashing cursor.
3) Turn the large FMS Knob to highlight ‘RENAME’ in the Pilot Profile Box.
Appendix
4)
Press the ENT Key.
5) In the ‘Rename Profile’ window, turn the FMS Knob to select the profile to
rename.
Index
6)
Press the ENT Key.
7) Use the FMS Knob to enter a new profile name up to 16 characters long
and press the ENT Key.
84
Garmin G1000 Cockpit Reference Guide for the Socata TBM 700
190-01247-01 Rev. A
Additional Features
9)
Flight
Instruments
8) With ‘RENAME’ highlighted, press the ENT Key.
To cancel the process, use the large FMS Knob to select ‘CANCEL’ and
press the ENT Key.
EAS
10) Press the FMS Knob to deactivate the cursor.
Deleting a Profile
2)
GPS Nav
1) Use the FMS Knob to select the AUX - System Setup Page.
Press the FMS Knob momentarily to activate the flashing cursor.
Flight
Planning
3) Turn the large FMS Knob to highlight ‘DELETE’ in the Pilot Profile Box.
4)
Press the ENT Key.
Procedures
5) In the ‘Delete Profile’ window, turn the FMS Knob to select the profile to
delete.
6)
Press the ENT Key.
9)
Press the FMS Knob to deactivate the cursor.
Additional
Features
To cancel the process, use the large FMS Knob to select ‘CANCEL’ and
press the ENT Key.
Hazard
Avoidance
7) With ‘DELETE’ highlighted, press the ENT Key.
8)
Insert an SD card containing the pilot profile(s) into the top card slot on the
MFD.
2)
Turn the FMS Knob to select the AUX - System Setup Page.
3)
Select the IMPORT Softkey.
4)
The system displays the Pilot Profile Importing Window with ‘IMPORT’
highlighted. To change the selected profile to be imported from the SD card
(shown as ‘SELECT FILE’), turn the large FMS Knob to highlight the profile
file name, then turn the small FMS Knob to highlight a profile from the list,
and press the ENT Key.
Index
85
Appendix
Garmin G1000 Cockpit Reference Guide for the Socata TBM 700
Annun/
Alerts
1)
Abnormal
Operation
Importing a Profile from an SD Card
190-01247-01 Rev. A
AFCS
desired profile to delete, select another profile, then delete the desired
profile.
Nav/Com/
XPDR/Audio
NOTE: The profile that is currently active cannot be deleted. If this is the
Additional Features
EAS
Flight
Instruments
5)
AFCS
Nav/Com/
XPDR/Audio
6)
7)
Flight
Planning
GPS Nav
8)
If desired, the profile name to be used after profile has been imported can
be changed by turning the FMS Knob to highlight the ‘PROFILE NAME’
field, then use the large and small FMS Knobs to enter the name, and press
the ENT Key. Imported profile names cannot begin with a blank space or
be named ‘DEFAULT’, ‘GARMIN DEFAULTS’ or ‘DEFAULT SETTINGS’.
With ‘IMPORT’ highlighted, press the ENT Key.
If the imported profile name is the same as an existing profile on the
system, the system displays an ‘Overwrite existing file? OK or CANCEL’
prompt. Press the ENT Key to replace profile on the system with the profile
imported from the SD card, or turn the FMS Knob to highlight ‘CANCEL’
and press the ENT Key to return to the Pilot Profile Importing Window.
If successful, the system displays ‘Pilot profile import succeeded.’ in the
IMPORT RESULTS window below. With ‘OK’ highlighted, press the ENT or
CLR Keys or press the FMS Knob to return to the AUX - System Setup Page.
The imported profile becomes the active profile.
Exporting a Profile to an SD Card
Procedures
1)
Hazard
Avoidance
2)
3)
Additional
Features
4)
Abnormal
Operation
5)
Index
Appendix
Annun/
Alerts
6)
7)
86
Insert the SD card for storing the Pilot Profile into the top card slot on the
MFD.
Turn the FMS Knob to select the AUX - System Setup Page.
If necessary, activate the desired pilot profile to export. Only the currently
active Pilot Profile can be exported.
Select the EXPORT Softkey. The system displays the Pilot Profile Exporting
Window.
To export the pilot profile using the current supplied name, press the ENT
Key with ‘EXPORT’ highlighted. To change the profile file name turn the
large FMS Knob to highlight the ‘SELECT FILE’ field, then enter the new
name with the large and small FMS Knobs, then press the ENT Key. Then
press the ENT Key with ‘EXPORT’ highlighted.
If the profile name to be exported is the same as an existing profile file
name on the SD card, the system displays an ‘Overwrite existing file? OK
or CANCEL’ prompt. Press the ENT Key to replace the profile on the SD
card with the profile to be exported, or turn the FMS Knob to highlight
‘CANCEL’ and press the ENT Key to return to the Pilot Profile Exporting
Window without exporting the profile.
If successful, the EXPORT RESULTS window displays ‘Pilot profile export
succeeded.’ With ‘OK’ highlighted, press the ENT or CLR Keys, or press the
FMS Knob to return to the AUX - System Setup Page.
Garmin G1000 Cockpit Reference Guide for the Socata TBM 700
190-01247-01 Rev. A
Abnormal Operation
Flight
Instruments
ABNORMAL OPERATION
REVERSIONARY MODE
GPS Nav
Flight
Planning
NOTE: The Socata TBM 700 Airplane Flight Manual (AFM) always takes
precedence over the information found in this section.
AFCS
• PFD1 – By pressing the DISPLAY BACKUP Button on the left audio panel.
• MFD – By pressing the DISPLAY BACKUP Button on the left or the right
audio panel.
• PFD2 – By pressing the DISPLAY BACKUP Button on the right audio
panel.
Nav/Com/
XPDR/Audio
Activation of reversionary display mode is accomplished by pressing the DISPLAY
BACKUP Button on the appropriate audio panel.
EAS
Reversionary mode must be entered manually in the case of PFD1, PFD2,
or MFD failure. In reversionary mode, critical flight instrumentation is combined
with engine instrumentation on the remaining display.
Procedures
ABNORMAL COM OPERATION
Abnormal
Operation
If GPS position is lost, or becomes invalid, selected hazards being displayed on the
Navigation Map Page are removed until GPS position is again established.
Additional
Features
HAZARD DISPLAYS WITH LOSS OF GPS POSITION
Hazard
Avoidance
When a COM tuning failure is detected by the system, the emergency frequency
(121.500 MHz) is automatically loaded into the active frequency field of the COM
radio for which the tuning failure was detected. In the event of a failure of both PFDs,
the emergency frequency (121.500 MHz) automatically becomes the active frequency
on both COM radios.
Annun/
Alerts
Appendix
Loss of Hazard Functions with Loss of GPS
Position
Index
190-01247-01 Rev. A
Garmin G1000 Cockpit Reference Guide for the Socata TBM 700
87
UNUSUAL ATTITUDES
The PFD ‘declutters’ when the aircraft enters an unusual attitude. Only the primary
functions are displayed in these situations.
The following information is removed from the PFD (and corresponding softkeys
are disabled) when the aircraft experiences unusual attitudes:
• Traffic Annunciations
• AFCS Annunciations
• Flight Director
Command Bars
• Inset Map
• Temperatures
• DME Information
Window
• Wind Data
• Selected Heading Box
• Selected Course Box
• Transponder Status
Box
• System Time
• PFD Setup Menu
• Windows displayed in
the lower right corner
of the PFD:
– Timer/References
– Nearest Airports
– Flight Plan
– Messages
– Procedures
– ADF/DME Tuning
• Barometric Minimum
Descent Altitude Box
• Glideslope, Glidepath,
and Vertical Deviation
Indicators
• Altimeter Barometric
Setting
• Radar Altimeter
• Selected Altitude
• VNV Target Altitude
Extreme Pitch Indication
DEAD RECKONING
While in Enroute or Oceanic phase of flight, if the G1000 detects an invalid GPS
solution or is unable to calculate a GPS position, the system automatically reverts to
Dead Reckoning (DR) Mode. In DR Mode, the G1000 uses its last-known position
combined with continuously updated airspeed and heading data (when available) to
calculate and display the aircraft’s current estimated position.
Index
Appendix
Annun/
Alerts
Abnormal
Operation
Additional
Features
Hazard
Avoidance
Procedures
Flight
Planning
GPS Nav
AFCS
Nav/Com/
XPDR/Audio
EAS
Flight
Instruments
Abnormal Operation
88
Garmin G1000 Cockpit Reference Guide for the Socata TBM 700
190-01247-01 Rev. A
Abnormal Operation
EAS
Nav/Com/
XPDR/Audio
AFCS
GPS Nav
Flight
Planning
Procedures
Hazard
Avoidance
Additional
Features
Abnormal
Operation
DR Mode is indicated on the G1000 by the appearance of the letters ‘DR’
superimposed in yellow over the ‘own aircraft’ symbol as shown in the following
figure. In addition, ‘DR’ is prominently displayed, also in yellow, on the HSI slightly
above and to the right of the aircraft symbol on the CDI as shown in the following
figure. The CDI deviation bar is displayed in yellow, but will be removed from the
display after 20 minutes. Lastly, but at the same time, a ‘GPS NAV LOST’ alert message
appears on the PFD.
Normal navigation using GPS/SBAS source data resumes automatically once a valid
GPS solution is restored.
It is important to note that estimated navigation data supplied by the G1000 in
DR Mode may become increasingly unreliable and must not be used as a sole means
of navigation. If, while in DR Mode, airspeed and/or heading data is also lost or
not available, the DR function may not be capable of estimating your position and,
consequently, the system may display a path that is different than the actual movement
of the aircraft. Estimated position information displayed by the G1000 through
DR while there is no heading and/or airspeed data available should not be used for
navigation.
DR Mode is inherently less accurate than the standard GPS/SBAS Mode due to the
lack of satellite measurements needed to determine a position. Changes in wind speed
and/or wind direction compounds the relative inaccuracy of DR Mode. Because of this
degraded accuracy, the crew must maintain position awareness using other navigation
equipment until GPS-derived position data is restored.
Flight
Instruments
NOTE: Dead Reckoning Mode only functions in Enroute (ENR) or Oceanic
(OCN) phase of flight. In all other phases, an invalid GPS solution produces
a “NO GPS POSITION” annunciation on the map and the G1000 stops
navigating in GPS Mode.
Annun/
Alerts
Appendix
Symbolic Aircraft
(Map pages and Inset Map)
Index
CDI ‘DR’ Indication on PFD
Dead Reckoning Indications
190-01247-01 Rev. A
Garmin G1000 Cockpit Reference Guide for the Socata TBM 700
89
As a result of operating in DR Mode, all GPS-derived data is computed based upon
an estimated position and is displayed as yellow text on the display to denote degraded
navigation source information. This data includes the following:
• Navigation Status Box fields except Active Leg, TAS, and DTK
• GPS Bearing Pointer
• Wind data and pointers in the Wind Data Box on the PFD
• Current Track Indicator
• All Bearing Pointer Distances
• Active Flight Plan distances, bearings, and ETE values
Also, while the G1000 is in DR Mode, the autopilot will couple to GPS for up to 20
minutes. Terrain Proximity, TERRAIN-SVS, and TAWS are also disabled. Additionally,
the accuracy of all nearest information (airports, airspaces, and waypoints) is
questionable. Finally, airspace alerts continue to function, but with degraded
accuracy.
Index
Appendix
Annun/
Alerts
Abnormal
Operation
Additional
Features
Hazard
Avoidance
Procedures
Flight
Planning
GPS Nav
AFCS
Nav/Com/
XPDR/Audio
EAS
Flight
Instruments
Abnormal Operation
90
Garmin G1000 Cockpit Reference Guide for the Socata TBM 700
190-01247-01 Rev. A
Annunciations & Alerts
Flight
Instruments
ANNUNCIATIONS & ALERTS
CAS MESSAGES
EAS
Warning Messages
Procedures
Hazard
Avoidance
Additional
Features
Abnormal
Operation
PARK BRAKE
TORQUE
Flight
Planning
OXYGEN
GPS Nav
OIL PRESS
Comments
Battery temperature over 70°C
Bleed temperature high
Cabin altitude over 10,000 ft
Cabin pressure differential over 6.2 psi
Pilot or cabin door open
Engine compartment fire (temperature over 200°C; if installed)
Dissymmetry between left- and right-hand flaps
Fuel tank selectors set to “Off”
Fuel pressure below 10 psi
Engine start (models A, B, & C): ITT over 1000°C, 870°C (5 seconds),
or 800°C (20 seconds)
Engine start (model N only): ITT over 1000°C, 870°C (5 seconds), or
840°C (20 seconds)
Engine running: ITT over 800°C
Oil pressure below 60 psi
Oxygen cylinder closed (gaseous oxygen systems). Oxygen system
has been activated (chemical oxygen systems).
Parking brake applied
Torque greater than or equal to 121.4% maximum torque (N only)
AFCS
ITT
Nav/Com/
XPDR/Audio
Messages
BAT OVERHEAT
BLEED TEMP
CABIN ALTITUDE
CABIN DIFF PRESS
DOOR
FIRE
FLAPS ASYM
FUEL OFF
FUEL PRESS
Annun/
Alerts
Appendix
Index
190-01247-01 Rev. A
Garmin G1000 Cockpit Reference Guide for the Socata TBM 700
91
Caution Messages
Messages
AP ON YD OFF
AUTO SEL
AUX BOOST PMP ON
BAT AMP
BAT OFF
BLEED OFF
CHIP
FRONT CARGO DOOR
FUEL IMBALANCE
GPS Nav
AFCS
Nav/Com/
XPDR/Audio
EAS
Flight
Instruments
Annunciations & Alerts
Index
Appendix
Annun/
Alerts
Abnormal
Operation
Additional
Features
Hazard
Avoidance
Procedures
Flight
Planning
FUEL LOW L-R*
GPU DOOR
IGNITION
INERT SEP FAIL
INERT SEP ON
LOW LVL FAIL L-R*
LOW VOLTAGE
MAIN GEN
NG HI
OIL PRESS
OIL TEMP
PITOT HT ON 1-2*
PITOT NO HT 1-2*
PROP DEICE FAIL
PROP DEICE ON
STALL HEAT ON
STALL NO HEAT
STARTER
VACUUM LOW
Comments
Autopilot is on and the Yaw Damper is off
Fuel timer off or out of service
Electric fuel pump running (manual or automatic mode)
Battery current over 50 A while on ground
Battery off
Flow control and shut-off valve/shut-off valve closed
Oil chip detector on (if installed)
Forward baggage door open
Fuel tanks imbalanced by more than 25 USGAL (A, B, and C) or
15 USGAL (N) for >30 seconds
Fuel quantity less than or equal to 9.1 USGAL in specified tank
GPU receptacle door not closed
Ignition exciter running
Inertial separator failure
Inertial separator extended
Low fuel level sensor failure for specified tank
Battery voltage below 26 V
Starter generator unconnected
Generator speed is more than 103%
Oil pressure between 60 and 100 psi
Oil temperature below 0°C or above 104°C
Specified pitot heat (#1 or #2) on while engine off
Specified pitot heat (#1 or #2) off
Prop deice selected and not on
Prop deice on while engine off
Stall warning heat on while engine off
Stall warning heat off
Starter generator running
Vacuum pressure less than 3.75 in Hg
* Only affected side (L, R, L-R or 1, 2, 1-2) displayed in CAS message; applicable messages listed here
display L-R or 1-2 for example
92
Garmin G1000 Cockpit Reference Guide for the Socata TBM 700
190-01247-01 Rev. A
Annunciations & Alerts
Flight
Instruments
COMPARATOR ANNUNCIATIONS
EAS
Comparator
Condition
Window Text
ALT MISCOMP Difference in altitude sensors is > 200 ft.
If both airspeed sensors detect < 35 knots, this is inhibited.
Nav/Com/
XPDR/Audio
IAS MISCOMP If either airspeed sensor detects > 35 knots, and the difference in sensors is > 10
kts.
If either airspeed sensor detects > 80 knots, and the difference in sensors is > 7
kts.
AFCS
HDG MISCOMP Difference in heading sensors is > 6 degrees.
PIT MISCOMP
Difference in pitch sensors is > 5 degrees.
GPS Nav
ROL MISCOMP Difference in roll sensors is > 6 degrees.
ALT NO COMP No data from one or both altitude sensors.
Flight
Planning
IAS NO COMP No data from one or both airspeed sensors.
HDG NO COMP No data from one or both heading sensors.
No data from one or both pitch sensors.
Procedures
PIT NO COMP
ROL NO COMP No data from one or both roll sensors.
Condition
Additional
Features
Both PFDs are displaying data from the number one Air Data Computer.
Both PFDs are displaying data from the number two Air Data Computer.
Both PFDs are displaying data from the number one Attitude & Heading Reference
System.
BOTH ON GPS1
BOTH ON GPS2
USING ADC1
USING ADC2
USING AHRS1
Both PFDs are displaying data from the number one GPS receiver.
Both PFDs are displaying data from the number two GPS receiver.
PFD2 is displaying data from the #1 Air Data Computer.
PFD1 is displaying data from the #2 Air Data Computer.
Index
190-01247-01 Rev. A
Appendix
Both PFDs are displaying data from the number two Attitude & Heading Reference
System.
PFD2 is displaying data from the #1 AHRS.
Garmin G1000 Cockpit Reference Guide for the Socata TBM 700
Annun/
Alerts
BOTH ON AHRS2
Abnormal
Operation
Reversionary
Sensor
Window Text
BOTH ON ADC1
BOTH ON ADC2
BOTH ON AHRS1
Hazard
Avoidance
REVERSIONARY SENSOR ANNUNCIATIONS
93
Annunciations & Alerts
Nav/Com/
XPDR/Audio
EAS
Flight
Instruments
Reversionary
Sensor
Window Text
USING AHRS2
USING GPS1
USING GPS2
Condition
PFD1 is displaying data from the #2 AHRS.
PFD2 is displaying data from the #1 GPS.
PFD1 is displaying data from the #2 GPS.
Alert Condition Annunciation
Rudder Mistrim
Right
Rudder Mistrim
Left
Aileron Mistrim
Right
Aileron Mistrim
Left
Elevator Mistrim
Down
Elevator Mistrim
Up
Pitch Trim Failure
Additional
Features
Hazard
Avoidance
Procedures
Flight
Planning
GPS Nav
AFCS
AFCS ALERTS
Abnormal
Operation
(or stuck MEPT
Switch)
Yaw Trim Failure
Appendix
Annun/
Alerts
(or stuck MEYT
Switch)
Yaw Damper
Failure
Index
Yaw servo providing sustained force in the indicated
direction. Aircraft rudder retrim after substantial pitch and
power changes required.
Roll servo providing sustained force in the indicated
direction
Pitch servo providing sustained force in the indicated
direction. May indicate a failure of the pitch trim servo or
trim system.
If AP engaged, take control of the aircraft and disengage AP
If AP disengaged, move MEPT switches separately to
unstick
If AP engaged, take control of the aircraft and disengage AP
If AP disengaged, move the MEYT switch to check if a stuck
switch is causing the annunciation
YD control failure; AP also inoperative
Roll Failure
Roll axis control failure; AP inoperative
Pitch Failure
Pitch axis control failure; AP inoperative
System Failure
94
Description
AP and MEPT are unavailable; FD may still be available
Garmin G1000 Cockpit Reference Guide for the Socata TBM 700
190-01247-01 Rev. A
Annunciations & Alerts
Description
Preflight Test
Nav/Com/
XPDR/Audio
Preflight system test failed; aural alert sounds at failure
EAS
Performing preflight system test; aural alert sounds at
completion
Do not press the AP DISC Switch during servo power-up
and preflight system tests as this may cause the preflight
system test to fail or never to start (if servos fail their powerup tests). Power must be cycled to the servos to remedy
the situation.
Flight
Instruments
Alert Condition Annunciation
AFCS
TERRAIN-SVS ALERTS
Aural
Message
Flight
Planning
MFD
Pop-Up Alert
GPS Nav
Alert Type
PFD/MFD
TERRAIN-SVS
Page
Annunciation
Reduced Required Obstacle
Clearance Warning (ROC)
“Warning; Obstacle,
Obstacle”
Imminent Obstacle Impact
Warning (IOI)
“Warning; Obstacle,
Obstacle”
Reduced Required Terrain
Clearance Caution (RTC)
“Caution; Terrain,
Terrain”
Imminent Terrain Impact
Caution (ITI)
“Caution; Terrain,
Terrain”
Reduced Required Obstacle
Clearance Caution (ROC)
“Caution; Obstacle,
Obstacle”
Imminent Obstacle Impact
Caution (IOI)
“Caution; Obstacle,
Obstacle”
Abnormal
Operation
“Warning; Terrain,
Terrain”
Additional
Features
Imminent Terrain Impact
Warning (ITI)
Hazard
Avoidance
“Warning; Terrain,
Terrain”
Procedures
Reduced Required Terrain
Clearance Warning (RTC)
Annun/
Alerts
Appendix
Index
190-01247-01 Rev. A
Garmin G1000 Cockpit Reference Guide for the Socata TBM 700
95
TERRAIN-SVS SYSTEM STATUS ANNUNCIATIONS
TERRAIN-SVS Page
Annunciation
Aural Message
TERRAIN TEST
None
None
“Terrain System
Test OK”
None
None
TERRAIN DATABASE FAILURE
None
Terrain System Test
Fail
TERRAIN FAIL
“Terrain System
Failure”
Terrain or Obstacle
database unavailable
or invalid,
invalid software
configuration, system
audio fault
TERRAIN FAIL
“Terrain System
Failure”
NO GPS POSITION
“Terrain System
Not Available”
None
“Terrain System
Not Available”
None
“Terrain System
Available”
Alert Type
PFD/MFD Alert
Annunciation
System Test in
Progress
System Test Pass
None
Terrain Alerting is
disabled
MFD Terrain or
Obstacle database
unavailable or invalid.
Terrain-SVS operating
with PFD Terrain or
Obstacle databases
None
No GPS position
Excessively degraded
GPS signal, Out of
database coverage
area
Sufficient GPS signal
received after loss
None
Index
Appendix
Annun/
Alerts
Abnormal
Operation
Additional
Features
Hazard
Avoidance
Procedures
Flight
Planning
GPS Nav
AFCS
Nav/Com/
XPDR/Audio
EAS
Flight
Instruments
Annunciations & Alerts
96
Garmin G1000 Cockpit Reference Guide for the Socata TBM 700
190-01247-01 Rev. A
Annunciations & Alerts
Alert Type
MFD
Pop-Up Alert
“Pull Up”
or
Imminent Obstacle
Impact Warning
(IOI)
or
or
“Terrain Ahead; Terrain Ahead”
or
“Caution, Terrain; Caution,
Terrain”
“Caution, Obstacle; Caution,
Obstacle”
or
“Obstacle Ahead; Obstacle
Ahead”
Appendix
or
Annun/
Alerts
Reduced Required
Obstacle Clearance
Caution (ROC)
or
“Caution, Terrain; Caution,
Terrain”
or
“Terrain Ahead; Terrain Ahead”
Abnormal
Operation
Imminent Terrain
Impact Caution (ITI)
“Obstacle Ahead, Pull Up;
Obstacle Ahead, Pull Up”
or
“Obstacle, Obstacle; Pull Up,
Pull Up”
Additional
Features
Reduced Required
Terrain Clearance
Caution (RTC)
“Obstacle, Obstacle; Pull Up,
Pull Up”
or
“Obstacle Ahead, Pull Up;
Obstacle Ahead, Pull Up”
Hazard
Avoidance
Reduced Required
Obstacle Clearance
Warning (ROC)
Terrain Ahead, Pull Up; Terrain
Ahead, Pull Up”
or
“Terrain, Terrain; Pull Up, Pull Up”
Procedures
or
Flight
Planning
Imminent Terrain
Impact Warning
(ITI)
“Terrain, Terrain; Pull Up, Pull Up”
or
“Terrain Ahead, Pull Up; Terrain
Ahead, Pull Up”
GPS Nav
or
AFCS
Reduced Required
Terrain Clearance
Warning (RTC)
Nav/Com/
XPDR/Audio
Excessive Descent
Rate Warning (EDR)
Aural Message
EAS
PFD/MFD
TAWS-B Page
Annunciation
Flight
Instruments
TAWS ALERTS
Index
190-01247-01 Rev. A
Garmin G1000 Cockpit Reference Guide for the Socata TBM 700
97
Alert Type
Hazard
Avoidance
Additional
Features
Abnormal
Operation
Annun/
Alerts
Appendix
Index
PFD/MFD
TAWS-B Page
Annunciation
MFD
Pop-Up Alert
Imminent Obstacle
Impact Caution
(IOI)
Aural Message
“Obstacle Ahead; Obstacle
Ahead”
or
“Caution, Obstacle; Caution,
Obstacle”
or
Premature Descent
Alert Caution (PDA)
Altitude Callout
“500”
“Too Low, Terrain”
None
None
“Five-Hundred”
Excessive Descent
Rate Caution (EDR)
“Sink Rate”
Negative Climb
Rate Caution
(NCR)
Procedures
Flight
Planning
GPS Nav
AFCS
Nav/Com/
XPDR/Audio
EAS
Flight
Instruments
Annunciations & Alerts
“Don’t Sink”
or
“Too Low, Terrain”
or
TAWS System Status Annunciations
TAWS-B Page Annunciation
Aural
Message
TAWS TEST
None
None
“TAWS System
Test OK”
None
None
TERRAIN DATABASE FAILURE
None
TAWS-B System Test Fail
TAWS FAIL
“TAWS System
Failure”
Terrain or Obstacle
database unavailable or
invalid, invalid software
configuration, system
audio fault
TAWS FAIL
“TAWS System
Failure”
Alert Type
PFD/MFD Alert
Annunciation
System Test in Progress
System Test Pass
None
TAWS Alerting is disabled
MFD Terrain or Obstacle
database unavailable or
invalid. TAWS operating
with PFD Terrain or
Obstacle databases
98
None
Garmin G1000 Cockpit Reference Guide for the Socata TBM 700
190-01247-01 Rev. A
Annunciations & Alerts
PFD/MFD Alert
Annunciation
No GPS position
None
NO GPS POSITION
“TAWS Not
Available”
None
“TAWS Not
Available”
None
“TAWS
Available”
Nav/Com/
XPDR/Audio
Sufficient GPS signal
received after loss
Aural
Message
EAS
Excessively degraded GPS
signal, Out of database
coverage area
TAWS-B Page Annunciation
Flight
Instruments
Alert Type
AFCS
VOICE ALERTS
“Minimums, minimums”
The aircraft has descended below the preset barometric minimum descent
altitude.
“Vertical track”
The aircraft is one minute from Top of Descent. Issued only when vertical
navigation is enabled.
“Airspeed, Airspeed”
Played when the indicated airspeed is below a given threshold for a
given aircraft configuration. Note this alert may be heard under normal
conditions during the landing flare.
“Traffic, Traffic”
The aircraft is outside the Traffic Information Service (TIS) coverage area.
Played when a Traffic Advisory (TA) is issued with a TAS system.
Played when the TAS system passes a pilot-initiated self test.
Additional
Features
“TAS System Test OK”
“TAS System Test Failed”
Played when a Traffic Advisory (TA) is issued with the TIS system.
Hazard
Avoidance
“Traffic Not Available”
Procedures
“Traffic”
Flight
Planning
Description
Played when the TAS system fails a pilot-initiated self test.
Played to indicate bearing of traffic from own aircraft (GTS 820 only).
“High”, “Low”, “Same
Altitude” (if within 200
feet of own altitude), or
“Altitude not available”
Played to indicate altitude of traffic relative to own aircraft (GTS 820 only).
Annun/
Alerts
Appendix
Played to indicate distance of traffic from own aircraft (GTS 820 only).
Index
190-01247-01 Rev. A
Abnormal
Operation
“One o’clock” through
“Twelve o’clock”
or “No Bearing”
“Less than one mile”,
“One Mile” through “Ten
Miles”, or “More than ten
miles”
GPS Nav
Voice Alert
Garmin G1000 Cockpit Reference Guide for the Socata TBM 700
99
MFD & PFD MESSAGE ADVISORIES
Message
Comments
DATA LOST – Pilot stored data was The pilot profile data was lost. System reverts
lost. Recheck settings.
to default pilot profile and settings. The pilot
may reconfigure the MFD & PFDs with preferred
settings, if desired.
XTALK ERROR – A flight display
The MFD and PFDs are not communicating
crosstalk error has occurred.
with each other. The G1000 system should be
serviced.
PFD1 SERVICE – PFD1 needs
service. Return unit for repair.
PFD2 SERVICE – PFD2 needs
The PFD and/or MFD self-test has detected a
service. Return unit for repair.
problem. The G1000 system should be serviced.
MFD1 SERVICE – MFD1 needs
service. Return unit for repair.
MANIFEST – PFD1 software
mismatch, communication halted.
MANIFEST – PFD2 software
The PFD and/or MFD has incorrect software
mismatch, communication halted. installed. The G1000 system should be serviced.
MANIFEST – MFD1 software
mismatch, communication halted.
PFD1 CONFIG – PFD1 config error.
The PFD configuration settings do not match
Config service req’d.
backup configuration memory. The G1000
PFD2 CONFIG – PFD2 config error. system should be serviced.
Config service req’d.
MFD1 CONFIG – MFD1 config
The MFD configuration settings do not match
error. Config service req’d.
backup configuration memory. The G1000
system should be serviced.
SW MISMATCH – GDU software
The MFD and PFDs have different software
version mismatch. Xtalk is off.
versions installed. The G1000 system should be
serviced.
Index
Appendix
Annun/
Alerts
Abnormal
Operation
Additional
Features
Hazard
Avoidance
Procedures
Flight
Planning
GPS Nav
AFCS
Nav/Com/
XPDR/Audio
EAS
Flight
Instruments
Annunciations & Alerts
100
Garmin G1000 Cockpit Reference Guide for the Socata TBM 700
190-01247-01 Rev. A
Annunciations & Alerts
Comments
Flight
Instruments
The PFD and/or MFD is overheating and is
reducing power consumption by dimming the
display. If problem persists, the G1000 system
should be serviced.
EAS
Nav/Com/
XPDR/Audio
A key is stuck on the PFD and/or MFD bezel.
Attempt to free the stuck key by pressing it
several times. The G1000 system should be
serviced if the problem persists.
AFCS
GPS Nav
Additional
Features
Abnormal
Operation
Comments
The MFD and/or PFD detected a failure in the
navigation database. Attempt to reload the
navigation database. If problem persists, the
G1000 system should be serviced.
Annun/
Alerts
Appendix
Message
MFD1 DB ERR – MFD1 navigation
database error exists.
PFD1 DB ERR – PFD1 navigation
database error exists.
PFD2 DB ERR – PFD2 navigation
database error exists.
Hazard
Avoidance
DATABASE MESSAGE ADVISORIES
Procedures
The PFD1 configuration module backup memory
has failed. The G1000 system should be
serviced.
The PFD1 voltage is low. The G1000 system
should be serviced.
The PFD2 voltage is low. The G1000 system
should be serviced.
The MFD voltage is low. The G1000 system
should be serviced.
Flight
Planning
Message
PFD1 COOLING – PFD1 has poor
cooling. Reducing power usage.
PFD2 COOLING – PFD2 has poor
cooling. Reducing power usage.
MFD1 COOLING – MFD1 has poor
cooling. Reducing power usage.
PFD1 KEYSTK – PFD1 [key name]
Key is stuck.
PFD2 KEYSTK – PFD2 [key name]
Key is stuck.
MFD1 KEYSTK – MFD [key name]
Key is stuck.
CNFG MODULE – PFD1
configuration module is
inoperative.
PFD1 VOLTAGE – PFD1 has low
voltage. Reducing power usage
PFD2 VOLTAGE – PFD2 has low
voltage. Reducing power usage
MFD1 VOLTAGE – MFD1 has low
voltage. Reducing power usage
Index
190-01247-01 Rev. A
Garmin G1000 Cockpit Reference Guide for the Socata TBM 700
101
Message
MFD1 DB ERR – MFD1 basemap
database error exists.
PFD1 DB ERR – PFD1 basemap
database error exists.
PFD2 DB ERR – PFD2 basemap
database error exists.
MFD1 DB ERR – MFD1 terrain
database error exists.
PFD1 DB ERR – PFD1 terrain
database error exists.
PFD2 DB ERR – PFD2 terrain
database error exists.
MFD1 DB ERR – MFD1 terrain
database missing.
PFD1 DB ERR – PFD1 terrain
database missing.
PFD2 DB ERR – PFD2 terrain
database missing.
MFD1 DB ERR – MFD1 obstacle
database error exists.
PFD1 DB ERR – PFD1 obstacle
database error exists.
PFD2 DB ERR – PFD2 obstacle
database error exists.
MFD1 DB ERR – MFD1 obstacle
database missing.
PFD1 DB ERR – PFD1 obstacle
database missing.
PFD2 DB ERR – PFD2 obstacle
database missing.
Comments
The MFD and/or PFD detected a failure in the
basemap database.
The MFD and/or PFD detected a failure in the
terrain database. Ensure that the terrain card is
properly inserted in display. Replace terrain card.
If problem persists, The G1000 system should be
serviced.
The terrain database is present on another LRU,
but is missing on the specified LRU.
The MFD and/or PFD detected a failure in the
obstacle database. Ensure that the data card is
properly inserted. Replace data card. If problem
persists, The G1000 system should be serviced.
The obstacle database is present on another LRU,
but is missing on the specified LRU.
Index
Appendix
Annun/
Alerts
Abnormal
Operation
Additional
Features
Hazard
Avoidance
Procedures
Flight
Planning
GPS Nav
AFCS
Nav/Com/
XPDR/Audio
EAS
Flight
Instruments
Annunciations & Alerts
102
Garmin G1000 Cockpit Reference Guide for the Socata TBM 700
190-01247-01 Rev. A
Annunciations & Alerts
Comments
Flight
Instruments
The MFD and/or PFD detected a failure in the
airport terrain database. Ensure that the data
card is properly inserted. Replace data card. If
problem persists, The G1000 system should be
serviced.
EAS
Nav/Com/
XPDR/Audio
Abnormal
Operation
Annun/
Alerts
Appendix
Index
103
Additional
Features
Garmin G1000 Cockpit Reference Guide for the Socata TBM 700
Hazard
Avoidance
190-01247-01 Rev. A
Procedures
The MFD detected a failure in the ChartView
database (optional feature). Ensure that the
data card is properly inserted. Replace data card.
If problem persists, The G1000 system should be
serviced.
MFD1 DB ERR – MFD1 FliteCharts The MFD detected a failure in the FliteCharts
database error exists.
database (optional feature). Ensure that the
data card is properly inserted. Replace data card.
If problem persists, The G1000 system should be
serviced.
DB MISMATCH – Navigation
The PFDs and MFD have different navigation
database version mismatch. Xtalk database versions installed. Crossfill is off.
is off.
Install correct navigation database version in all
displays.
Flight
Planning
The MFD and/or PFD detected a failure in the
Safe Taxi database. Ensure that the data card is
properly inserted. Replace data card. If problem
persists, The G1000 system should be serviced.
GPS Nav
The airport terrain database is present on
another LRU, but is missing on the specified LRU.
AFCS
Message
MFD1 DB ERR – MFD1 airport
terrain database error exists.
PFD1 DB ERR – PFD1 airport
terrain database error exists.
PFD2 DB ERR – PFD2 airport
terrain database error exists.
MFD1 DB ERR – MFD1 airport
terrain database missing.
PFD1 DB ERR – PFD1 airport
terrain database missing.
PFD2 DB ERR – PFD2 airport
terrain database missing.
MFD1 DB ERR – MFD1 Safe Taxi
database error exists.
PFD1 DB ERR – PFD1 Safe Taxi
database error exists.
PFD2 DB ERR – PFD2 Safe Taxi
database error exists.
MFD1 DB ERR – MFD1 Chartview
database error exists.
Message
DB MISMATCH – Navigation
database type mismatch. Xtalk is
off.
Comments
The PFDs and MFD have different navigation
database types installed (Americas, European,
etc.). Crossfill is off. Install correct navigation
database type in all displays.
DB MISMATCH – Terrain database The PFDs and MFD have different terrain
version mismatch.
database versions installed. Install correct terrain
database version in all displays.
DB MISMATCH – Terrain database The PFDs and MFD have different terrain
type mismatch.
database types installed. Install correct terrain
database type in all displays.
DB MISMATCH – Obstacle
The PFDs and MFD have different obstacle
database version mismatch.
database versions installed. Install correct
obstacle database version in all displays.
DB MISMATCH – Airport Terrain
The PFDs and MFD have different airport terrrain
database mismatch.
databases installed. Install correct airport terrain
database in all displays.
NAV DB UPDATED – Active
System has updated the active navigation
navigation database updated.
database from the standby navigation database.
TERRAIN DSP – [PFD1, PFD2 or
One of the terrain, airport terrain, or obstacle
MFD1] Terrain awareness display
databases required for TAWS in the specified PFD
unavailable.
or MFD is missing or invalid.
GMA 1347D MESSAGE ADVISORIES
Message
Comments
GMA1 FAIL – GMA1 is inoperative. The audio panel self-test has detected a failure.
GMA2 FAIL – GMA2 is inoperative. The audio panel is unavailable. The G1000
system should be serviced.
GMA XTALK – GMA crosstalk error An error has occurred in transferring data
has occurred.
between the two GMAs. The G1000 system
should be serviced.
Index
Appendix
Annun/
Alerts
Abnormal
Operation
Additional
Features
Hazard
Avoidance
Procedures
Flight
Planning
GPS Nav
AFCS
Nav/Com/
XPDR/Audio
EAS
Flight
Instruments
Annunciations & Alerts
104
Garmin G1000 Cockpit Reference Guide for the Socata TBM 700
190-01247-01 Rev. A
Annunciations & Alerts
Comments
Flight
Instruments
The audio panel configuration settings do not
match backup configuration memory. The
G1000 system should be serviced.
EAS
The audio panel has incorrect software installed. The
G1000 system should be serviced.
Flight
Planning
Comments
Appendix
Index
Garmin G1000 Cockpit Reference Guide for the Socata TBM 700
Annun/
Alerts
The GIA1 and/or GIA2 temperature is too high.
If problem persists, the G1000 system should be
serviced.
Abnormal
Operation
The GIA1 and/or GIA2 temperature is too low
to operate correctly. Allow units to warm up to
operating temperature.
Additional
Features
The GIA1 and/or GIA2 have an error in the audio
configuration. The G1000 system should be
serviced.
Hazard
Avoidance
The GIA1 and/or GIA2 configuration settings do
not match backup configuration memory. The
G1000 system should be serviced.
Procedures
190-01247-01 Rev. A
GPS Nav
GIA 63W MESSAGE ADVISORIES
Message
GIA1 CONFIG – GIA1 config error.
Config service req’d.
GIA2 CONFIG – GIA2 config error.
Config service req’d.
GIA1 CONFIG – GIA1 audio config
error. Config service req’d.
GIA2 CONFIG – GIA2 audio config
error. Config service req’d.
GIA1 COOLING – GIA1
temperature too low.
GIA2 COOLING – GIA2
temperature too low.
GIA1 COOLING – GIA1 over
temperature.
GIA2 COOLING – GIA2 over
temperature.
AFCS
The audio panel self-test has detected a problem in
the unit. Certain audio functions may still be available, and the audio panel may still be usable. The
G1000 system should be serviced when possible.
Nav/Com/
XPDR/Audio
Message
GMA1 CONFIG – GMA1 config
error. Config service req’d.
GMA2 CONFIG – GMA2 config
error. Config service req’d.
MANIFEST – GMA1 software
mismatch, communication halted.
MANIFEST – GMA2 software
mismatch, communication halted.
GMA1 SERVICE – GMA1 needs
service. Return unit for repair.
GMA2 SERVICE – GMA2 needs
service. Return unit for repair.
105
Message
GIA1 SERVICE – GIA1 needs
service. Return the unit for repair.
GIA2 SERVICE – GIA2 needs
service. Return the unit for repair.
HW MISMATCH – GIA hardware
mismatch. GIA1 communication
halted.
HW MISMATCH – GIA hardware
mismatch. GIA2 communication
halted.
MANIFEST – GIA1 software
mismatch, communication halted.
MANIFEST – GIA2 software
mismatch, communication halted.
MANIFEST – GFC software
mismatch, communication halted.
COM1 TEMP – COM1 over temp.
Reducing transmitter power.
COM2 TEMP – COM2 over temp.
Reducing transmitter power.
Comments
COM1 SERVICE – COM1 needs
service. Return unit for repair.
COM2 SERVICE – COM2 needs
service. Return unit for repair.
COM1 PTT – COM1 push-to-talk
key is stuck.
COM2 PTT – COM2 push-to-talk
key is stuck.
The system has detected a failure in COM1
and/or COM2. COM1 and/or COM2 may still be
usable. The G1000 system should be serviced
when possible.
The GIA1 and/or GIA2 self-test has detected a
problem in the unit. The G1000 system should
be serviced.
A GIA mismatch has been detected, where only
one is SBAS capable.
The GIA1 and/or GIA 2 has incorrect software
installed. The G1000 system should be serviced.
Incorrect servo software is installed, or gain
settings are incorrect.
The system has detected an over temperature
condition in COM1 and/or COM2. The
transmitter is operating at reduced power. If the
problem persists, the G1000 system should be
serviced.
The COM1 and/or COM2 external push-to-talk
switch is stuck in the enable (or “pressed”)
position. Press the PTT switch again to cycle its
operation.
If the problem persists, the G1000 system should
be serviced.
Index
Appendix
Annun/
Alerts
Abnormal
Operation
Additional
Features
Hazard
Avoidance
Procedures
Flight
Planning
GPS Nav
AFCS
Nav/Com/
XPDR/Audio
EAS
Flight
Instruments
Annunciations & Alerts
106
Garmin G1000 Cockpit Reference Guide for the Socata TBM 700
190-01247-01 Rev. A
Annunciations & Alerts
EAS
Nav/Com/
XPDR/Audio
AFCS
GPS Nav
Flight
Planning
Procedures
Hazard
Avoidance
Additional
Features
Abnormal
Operation
Annun/
Alerts
Comments
The COM1 and/or COM2 transfer switch is stuck
in the enabled (or “pressed”) position. Press the
transfer switch again to cycle its operation. If
the problem persists, the G1000 system should
be serviced.
LOI – GPS integrity lost. Crosscheck GPS integrity is insufficient for the current phase
with other NAVS.
of flight.
GPS NAV LOST – Loss of GPS
Loss of GPS navigation due to insufficient
navigation. Insufficient satellites.
satellites.
GPS NAV LOST – Loss of GPS
Loss of GPS navigation due to position error.
navigation. Position error.
GPS NAV LOST – Loss of GPS
Loss of GPS navigation due to GPS failure.
navigation. GPS fail.
ABORT APR – Loss of GPS
Abort approach due to loss of GPS navigation.
navigation. Abort approach.
APR DWNGRADE – Approach
Vertical guidance generated by SBAS is
downgraded.
unavailable, use LNAV only minimums.
TRUE APR – True north approach. Displayed after passing the first waypoint of a
Change HDG reference to TRUE.
true north approach when the nav angle is set
to ‘AUTO’.
GPS1 SERVICE – GPS1 needs
A failure has been detected in the GPS1
service. Return unit for repair.
and/or GPS2 receiver. The receiver may still be
GPS2 SERVICE – GPS2 needs
available. The G1000 system should be serviced.
service. Return unit for repair.
NAV1 SERVICE – NAV1 needs
A failure has been detected in the NAV1
service. Return unit for repair.
and/or NAV2 receiver. The receiver may still be
NAV2 SERVICE – NAV2 needs
available. The G1000 system should be serviced.
service. Return unit for repair.
Flight
Instruments
Message
COM1 RMT XFR – COM1 remote
transfer key is stuck.
COM2 RMT XFR – COM2 remote
transfer key is stuck.
Appendix
Index
190-01247-01 Rev. A
Garmin G1000 Cockpit Reference Guide for the Socata TBM 700
107
Message
NAV1 RMT XFR – NAV1 remote
transfer key is stuck.
NAV2 RMT XFR – NAV2 remote
transfer key is stuck.
Comments
The remote NAV1 and/or NAV2 transfer switch
is stuck in the enabled (or “pressed”) state.
Press the transfer switch again to cycle its
operation. If the problem persists, the G1000
system should be serviced.
G/S1 FAIL – G/S1 is inoperative.
G/S2 FAIL – G/S2 is inoperative.
A failure has been detected in glideslope
receiver 1 and/or receiver 2. The G1000 system
should be serviced.
G/S1 SERVICE – G/S1 needs
service. Return unit for repair.
G/S2 SERVICE – G/S2 needs
service. Return unit for repair.
A failure has been detected in glideslope
receiver 1 and/or receiver 2. The receiver may
still be available. The G1000 system should be
serviced when possible.
GEA 71 MESSAGE ADVISORIES
Message
Comments
GEA1 CONFIG – GEA1 config error. The GEA1 configuration settings do not match
Config service req’d.
those of backup configuration memory. The
G1000 system should be serviced.
GEA2 CONFIG – GEA2 config error. The GEA2 configuration settings do not match
Config service req’d.
those of backup configuration memory. The
G1000 system should be serviced.
MANIFEST – GEA1 software
The #1 GEA 71 has incorrect software installed.
mismatch, communication halted. The G1000 system should be serviced.
MANIFEST – GEA2 software
The #2 GEA 71 has incorrect software installed.
mismatch, communication halted. The G1000 system should be serviced.
Index
Appendix
Annun/
Alerts
Abnormal
Operation
Additional
Features
Hazard
Avoidance
Procedures
Flight
Planning
GPS Nav
AFCS
Nav/Com/
XPDR/Audio
EAS
Flight
Instruments
Annunciations & Alerts
108
Garmin G1000 Cockpit Reference Guide for the Socata TBM 700
190-01247-01 Rev. A
Annunciations & Alerts
Procedures
Hazard
Avoidance
Additional
Features
Abnormal
Operation
Annun/
Alerts
Appendix
AHRS2 TAS – AHRS2 not receiving
valid airspeed.
Comments
The #1 AHRS is not receiving true airspeed from
the air data computer. The AHRS relies on GPS
information to augment the lack of airspeed.
The G1000 system should be serviced.
The #2 AHRS is not receiving true airspeed from
the air data computer. The AHRS relies on GPS
information to augment the lack of airspeed.
The G1000 system should be serviced.
Flight
Planning
Message
AHRS1 TAS – AHRS1 not receiving
valid airspeed.
GPS Nav
GRS 77 MESSAGE ADVISORIES
AFCS
MANIFEST – GTX1 software
mismatch, communication halted.
MANIFEST – GTX2 software
mismatch, communication halted.
XPDR1 SRVC – XPDR1 needs
service. Return unit for repair.
XPDR2 SRVC – XPDR2 needs
service. Return unit for repair.
XPDR1 FAIL – XPDR1 is
inoperative.
XPDR2 FAIL – XPDR2 is
inoperative.
Nav/Com/
XPDR/Audio
XPDR2 CONFIG – XPDR2 config
error. Config service req’d.
Comments
The transponder configuration settings do not
match those of backup configuration memory.
The G1000 system should be serviced.
The transponder configuration settings do not
match those of backup configuration memory.
The G1000 system should be serviced.
The transponder has incorrect software installed.
The G1000 system should be serviced.
The transponder has incorrect software installed.
The G1000 system should be serviced.
The #1 transponder should be serviced when
possible.
The #2 transponder should be serviced when
possible.
There is no communication with the #1
transponder.
There is no communication with the #2
transponder.
EAS
Message
XPDR1 CONFIG – XPDR1 config
error. Config service req’d.
Flight
Instruments
GTX 33/33D MESSAGE ADVISORIES
Index
190-01247-01 Rev. A
Garmin G1000 Cockpit Reference Guide for the Socata TBM 700
109
Message
Comments
AHRS1 GPS – AHRS1 using backup The #1 AHRS is using the backup GPS path.
GPS source.
Primary GPS path has failed. The G1000 system
should be serviced when possible.
AHRS2 GPS – AHRS2 using backup The #2 AHRS is using the backup GPS path.
GPS source.
Primary GPS path has failed. The G1000 system
should be serviced when possible.
AHRS1 GPS – AHRS1 not receiving The #1 AHRS is not receiving any or any useful
any GPS information.
GPS information. Check AFMS limitations. The
G1000 system should be serviced.
AHRS2 GPS – AHRS2 not receiving The #2 AHRS is not receiving any or any useful
any GPS information.
GPS information. Check AFMS limitations. The
G1000 system should be serviced.
AHRS1 GPS – AHRS1 not receiving The #1 AHRS is not receiving backup GPS
backup GPS information.
information. The G1000 system should be
serviced.
AHRS2 GPS – AHRS2 not receiving The #2 AHRS is not receiving backup GPS
backup GPS information.
information. The G1000 system should be
serviced.
AHRS1 GPS – AHRS1 operating
The #1 AHRS is operating exclusively in no-GPS
exclusively in no-GPS mode.
mode. The G1000 system should be serviced.
AHRS2 GPS – AHRS2 operating
The #2 AHRS is operating exclusively in no-GPS
exclusively in no-GPS mode.
mode. The G1000 system should be serviced.
AHRS MAG DB – AHRS magnetic
The #1 AHRS and #2 AHRS magnetic model
model database version mismatch. database versions do not match.
AHRS1 SRVC – AHRS1 Magnetic- The #1 AHRS earth magnetic field model is out
field model needs update.
of date. Update magnetic field model when
practical.
AHRS2 SRVC – AHRS2 Magnetic- The #2 AHRS earth magnetic field model is out
field model needs update.
of date. Update magnetic field model when
practical.
Index
Appendix
Annun/
Alerts
Abnormal
Operation
Additional
Features
Hazard
Avoidance
Procedures
Flight
Planning
GPS Nav
AFCS
Nav/Com/
XPDR/Audio
EAS
Flight
Instruments
Annunciations & Alerts
110
Garmin G1000 Cockpit Reference Guide for the Socata TBM 700
190-01247-01 Rev. A
Annunciations & Alerts
Comments
Flight
Instruments
The aircraft is outside geographical limits for
approved AHRS operation. Heading is flagged
as invalid.
EAS
The #1 AHRS has incorrect software installed.
The G1000 system should be serviced.
The #2 AHRS has incorrect software installed.
The G1000 system should be serviced.
Nav/Com/
XPDR/Audio
AFCS
Message
GEO LIMITS – AHRS1 too far
North/South, no magnetic compass.
GEO LIMITS – AHRS2 too far
North/South, no magnetic compass.
MANIFEST – GRS1 software
mismatch, communication halted.
MANIFEST – GRS2 software
mismatch, communication halted.
GMU 44 MESSAGE ADVISORIES
Procedures
Hazard
Avoidance
Additional
Features
The GMU 44 has incorrect software installed.
The G1000 system should be serviced.
Abnormal
Operation
MANIFEST – GMU1 software
mismatch, communication halted.
MANIFEST – GMU2 software
mismatch, communication halted.
Comments
A fault has occurred in the #1 GMU 44.
Heading is flagged as invalid. The AHRS uses
GPS for backup mode operation. The G1000
system should be serviced.
A fault has occurred in the #2 GMU 44.
Heading is flagged as invalid. The AHRS uses
GPS for backup mode operation. The G1000
system should be serviced.
Flight
Planning
HDG FAULT – AHRS2
magnetometer fault has occurred.
GPS Nav
Message
HDG FAULT – AHRS1
magnetometer fault has occurred.
Annun/
Alerts
Appendix
Index
190-01247-01 Rev. A
Garmin G1000 Cockpit Reference Guide for the Socata TBM 700
111
GDL 69A MESSAGE ADVISORIES
Message
GDL69 CONFIG – GDL 69 config
error. Config service req’d.
GDL69 FAIL – GDL 69 has failed.
MANIFEST – GDL software
mismatch, communication halted.
Message
GWX CONFIG – GWX config error.
Config service req’d.
GWX FAIL – GWX is inoperative.
Additional
Features
GWX SERVICE – GWX needs
service. Return unit for repair.
MANIFEST – GWX software
mismatch, communication halted.
WX ALERT – Possible severe
weather ahead.
Comments
GWX configuration settings do not match those
of the GDU configuration. The G1000 system
should be serviced.
The GDU is not recieving status packet from the
GWX or the GWX is reporting a fault. The GWX
radar system should be serviced.
A failure has been detected in the GWX. The
GWX may still be usable.
The GWX has incorrect software installed. The
G1000 system should be serviced.
Possible severe weather detected within +/- 10
degrees of the aircraft heading at a range of 80
to 320 nm.
Index
Appendix
Annun/
Alerts
Abnormal
Operation
Comments
GDL 69 configuration settings do not match
those of backup configuration memory. The
G1000 system should be serviced.
A failure has been detected in the GDL 69.
The receiver is unavailable. The G1000 system
should be serviced
The GDL 69 has incorrect software installed.
The G1000 system should be serviced.
GWX MESSAGE ADVISORIES
Hazard
Avoidance
Procedures
Flight
Planning
GPS Nav
AFCS
Nav/Com/
XPDR/Audio
EAS
Flight
Instruments
Annunciations & Alerts
112
Garmin G1000 Cockpit Reference Guide for the Socata TBM 700
190-01247-01 Rev. A
Annunciations & Alerts
Comments
EAS
GDC1 or GDC2 is reporting that the altitude
error correction is unavailable.
Nav/Com/
XPDR/Audio
GDC1 or GDC2 is reporting that the airspeed
error correction is unavailable.
AFCS
GPS Nav
The GDC 74B has incorrect software installed.
The G1000 system should be serviced.
Flight
Planning
Message
ADC1 ALT EC – ADC1 altitude error
correction is unavailable.
ADC2 ALT EC – ADC2 altitude error
correction is unavailable.
ADC1 AS EC – ADC1 airspeed error
correction is unavailable.
ADC2 AS EC – ADC2 airspeed error
correction is unavailable.
MANIFEST – GDC1 software
mismatch, communication halted.
MANIFEST – GDC2 software
mismatch, communication halted.
Flight
Instruments
GDC 74B MESSAGE ADVISORIES
Abnormal
Operation
Annun/
Alerts
MANIFEST – GCU software
mismatch, communication halted.
GCU KEYSTK – GCU [key name]
Key is stuck.
Additional
Features
GCU FAIL – GCU is inoperative.
Comments
GCU 475 configuration settings do not match
those of backup configuration memory. The
G1000 system should be serviced.
A failure has been detected in the GCU 475.
The GCU 475 is unavailable.
The GCU 475 has incorrect software installed.
The G1000 system should be serviced.
A key is stuck on the GCU 475 bezel. Attempt
to free the stuck key by pressing it several times.
The G1000 system should be serviced if the
problem persists.
Hazard
Avoidance
Message
GCU CNFG – GCU Config error.
Config service req’d.
Procedures
GCU 475 MESSAGE ADVISORIES
Appendix
Index
190-01247-01 Rev. A
Garmin G1000 Cockpit Reference Guide for the Socata TBM 700
113
GMC 710 MESSAGE ADVISORIES
Message
GMC CONFIG – GMC Config error.
Config service req’d.
GMC FAIL – GMC is inoperative.
MANIFEST – GMC software
mismatch. Communication halted.
GMC KEYSTK – GMC [key name]
Key is stuck.
Comments
Error in the configuration of the GMC 710.
A failure has been detected in the GMC 710.
The GMC 710 is unavailable.
The GMC 710 has incorrect software installed.
The G1000 system should be serviced.
A key is stuck on the GMC 710 bezel. Attempt
to free the stuck key by pressing it several times.
The G1000 system should be serviced if the
problem persists.
GTS 820 MESSAGE ADVISORIES
Message
GTS CONFIG – GTS config error.
Config service req’d.
MANIFEST – GTS software
mismatch, communication halted.
Comments
The GTS and GDU have incompatible
configurations. This alert is also set when the
GTS has an invalid mode S address configured or
the mode S address does not match both XPDR
mode S addresses.
The GTS has incorrect software installed. The
G1000 system should be serviced.
GSR 56 MESSAGE ADVISORIES
Message
GSR1 FAIL – GSR1 has failed.
Comments
A fault has been detected in the #1 GSR 56.
The system should be serviced.
Index
Appendix
Annun/
Alerts
Abnormal
Operation
Additional
Features
Hazard
Avoidance
Procedures
Flight
Planning
GPS Nav
AFCS
Nav/Com/
XPDR/Audio
EAS
Flight
Instruments
Annunciations & Alerts
114
Garmin G1000 Cockpit Reference Guide for the Socata TBM 700
190-01247-01 Rev. A
Annunciations & Alerts
Nav/Com/
XPDR/Audio
AFCS
GPS Nav
Flight
Planning
Procedures
Hazard
Avoidance
Additional
Features
Abnormal
Operation
Annun/
Alerts
Appendix
Comments
Upon power-up, the G1000 system detects that
a stored flight plan waypoint is locked. This
occurs when an navigation database update
eliminates an obsolete waypoint. The flight
plan cannot find the specified waypoint and
flags this message. This can also occur with
user waypoints in a flight plan that is deleted.
Remove the waypoint from the flight plan if it
no longer exists in any database,
Or
update the waypoint name/identifier to reflect
the new information.
FPL WPT MOVE – Flight plan
The system has detected that a waypoint
waypoint moved.
coordinate has changed due to a new
navigation database update. Verify that stored
flight plans contain correct waypoint locations.
TIMER EXPIRD – Timer has expired. The system notifies the pilot that the timer has
expired.
DB CHANGE – Database changed. This occurs when a stored flight plan contains
Verify user modified procedures.
procedures that have been manually edited.
This alert is issued only after an navigation
database update. Verify that the user-modified
procedures in stored flight plans are correct and
up to date.
DB CHANGE – Database changed. This occurs when a stored flight plan contains
Verify stored airways.
an airway that is no longer consistent with the
navigation database. This alert is issued only
after an navigation database update. Verify
use of airways in stored flight plans and reload
airways as needed.
EAS
Message
FPL WPT LOCK – Flight plan
waypoint is locked.
Flight
Instruments
MISCELLANEOUS MESSAGE ADVISORIES
Index
190-01247-01 Rev. A
Garmin G1000 Cockpit Reference Guide for the Socata TBM 700
115
Index
Appendix
Annun/
Alerts
Abnormal
Operation
Additional
Features
Hazard
Avoidance
Procedures
Flight
Planning
GPS Nav
AFCS
Nav/Com/
XPDR/Audio
EAS
Flight
Instruments
Annunciations & Alerts
Message
FPL TRUNC – Flight plan has been
truncated.
Comments
This occurs when a newly installed navigation
database eliminates an obsolete approach
or arrival used by a stored flight plan. The
obsolete procedure is removed from the flight
plan. Update flight plan with current arrival or
approach.
LOCKED FPL – Cannot navigate
This occurs when the pilot attempts to activate
locked flight plan.
a stored flight plan that contains locked
waypoint. Remove locked waypoint from flight
plan. Update flight plan with current waypoint.
WPT ARRIVAL – Arriving at
Arriving at waypoint [xxxx], where [xxxx] is the
waypoint -[xxxx]
waypoint name.
STEEP TURN – Steep turn ahead.
A steep turn is 15 seconds ahead. Prepare to
turn.
INSIDE ARSPC – Inside airspace.
The aircraft is inside the airspace.
ARSPC AHEAD – Airspace ahead
Special use airspace is ahead of aircraft. The
less than 10 minutes.
aircraft will penetrate the airspace within 10
minutes.
ARSPC NEAR – Airspace near and Special use airspace is near and ahead of the
ahead.
aircraft position.
ARSPC NEAR – Airspace near – less Special use airspace is within 2 nm of the
than 2 nm.
aircraft position.
APR INACTV – Approach is not
The system notifies the pilot that the loaded
active.
approach is not active. Activate approach when
required.
SLCT FREQ – Select appropriate
The system notifies the pilot to load the
frequency for approach.
approach frequency for the appropriate NAV
receiver. Select the correct frequency for the
approach.
SLCT NAV – Select NAV on CDI for The system notifies the pilot to set the CDI to
approach.
the correct NAV receiver. Set the CDI to the
correct NAV receiver.
116
Garmin G1000 Cockpit Reference Guide for the Socata TBM 700
190-01247-01 Rev. A
Annunciations & Alerts
Comments
Flight
Instruments
Bad parallel track geometry.
EAS
Invalid leg type for parallel offset.
Procedures
Hazard
Avoidance
Additional
Features
Abnormal
Operation
Annun/
Alerts
Appendix
Index
117
Flight
Planning
Garmin G1000 Cockpit Reference Guide for the Socata TBM 700
GPS Nav
190-01247-01 Rev. A
AFCS
IAF waypoint for parallel offset has been
passed.
The current vertical waypoint can not be
reached within the maximum flight path angle
and vertical speed constraints. The system
automatically transitions to the next vertical
waypoint.
VNV – Unavailable. Unsupported
The lateral flight plan contains a procedure
leg type in flight plan.
turn, vector, or other unsupported leg type
prior to the active vertical waypoint. This
prevents vertical guidance to the active vertical
waypoint.
VNV – Unavailable. Excessive track The current track angle error exceeds the limit,
angle error.
causing the vertical deviation to go invalid.
VNV – Unavailable. Excessive
The current crosstrack exceeds the limit,
crosstrack error.
causing vertical deviation to go invalid.
VNV – Unavailable. Parallel course A parallel course has been selected, causing
selected.
the vertical deviation to go invalid.
NON WGS84 WPT – Do not use GPS The position of the selected waypoint [xxxx]
navigation to [xxxx].
is not calculated based on the WGS84 map
reference datum and may be positioned in
error as displayed. Do not use GPS to navigate
to the selected non-WGS84 waypoint.
TRAFFIC FAIL – Traffic device has
The G1000 is no longer receiving data from
failed.
the traffic system. The traffic device should be
serviced.
FAILED PATH – A data path has
A data path connected to the GDU or the GIA
failed.
63/W has failed.
Nav/Com/
XPDR/Audio
Message
PTK FAIL – Parallel track unavailable:
bad geometry.
PTK FAIL – Parallel track unavailable:
invalid leg type.
PTK FAIL – Parallel track unavailable:
past IAF.
UNABLE V WPT – Can’t reach
current vertical waypoint.
Message
MAG VAR WARN – Large magnetic
variance. Verify all course angles.
Comments
The GDU’s internal model cannot determine
the exact magnetic variance for geographic
locations near the magnetic poles. Displayed
magnetic course angles may differ from the
actual magnetic heading by more than 2°.
SVS – SVS DISABLED: Out of
Synthetic Vision is disabled because the aircraft
available terrain region.
is not within the boundaries of the installed
terrain database.
SVS – SVS DISABLED: Terrain DB
Synthetic Vision is disabled because a terrain
resolution too low.
database of sufficient resolution (9 arc-second
or better) is not currently installed.
SCHEDULER [#] – <message>.
Message criteria entered by the user.
ECS – Service required.
The environmental control system has failed.
CRUISE I – Cruise I conditions met. Cruise I engine trend data log has been
captured.
CRUISE II – Cruise II conditions met. Cruise II engine trend data log has been
captured.
EXCEEDANCE – Engine exceedance
An engine exceedance log has been captured.
data is being logged.
Index
Appendix
Annun/
Alerts
Abnormal
Operation
Additional
Features
Hazard
Avoidance
Procedures
Flight
Planning
GPS Nav
AFCS
Nav/Com/
XPDR/Audio
EAS
Flight
Instruments
Annunciations & Alerts
118
Garmin G1000 Cockpit Reference Guide for the Socata TBM 700
190-01247-01 Rev. A
Annunciations & Alerts
Flight
Instruments
FLIGHT PLAN IMPORT/EXPORT MESSAGES
In some circumstances, some messages may appear in conjunction with others.
Description
EAS
Flight Plan Import/Export
Results
Some flight plan waypoints were successfully imported from
the SD card, however others had errors and were not imported.
A partial stored flight plan now exists in the system.
‘File contained user waypoints only.’
The file stored on the SD card did not contain a flight plan,
only user waypoints. One or more of these waypoints did not
import successfully.
‘Too many points. Flight plan truncated.’
The flight plan on the SD card contains more waypoints than
the system can support. The flight plan was imported with as
many waypoints as possible.
‘Some waypoints not loaded. Waypoints locked.’
The flight plan on the SD card contains one or more waypoints
that the system cannot find in the navigation database. The
flight plan has been imported, but must be edited within the
system before it can be activated for use.
‘User waypoint database full. Not all
loaded.’
The flight plan file on the SD card contains user waypoints.
The quantity of stored user waypoints has exceeded system
capacity, therefore not all the user waypoints on the SD card
have been imported. Any flight plan user waypoints that were
not imported are locked in the flight plan. The flight plan must
be edited within the system before it can be activated for use.
The stored flight plan was successfully exported to the SD card.
‘Flight plan export failed.’
The stored flight plan was not successfully exported to the SD
card. The SD card may not have sufficient available memory or
the card may have been removed prematurely.
190-01247-01 Rev. A
Garmin G1000 Cockpit Reference Guide for the Socata TBM 700
119
Index
‘Flight plan successfully exported.’
Appendix
‘One or more user waypoints renamed.’ One or more imported user waypoints were renamed when
imported due to naming conflicts with waypoints already
existing in the system.
Annun/
Alerts
‘Flight plan partially imported.’
Abnormal
Operation
Flight plan data was not successfully imported from the SD card.
Additional
Features
‘Flight plan import failed.’
Hazard
Avoidance
The SD card contains no flight plan data.
Procedures
‘No flight plan files found to import.’
Flight
Planning
The file stored on the SD card did not contain a flight plan,
only user waypoints. These waypoints have been saved to the
system user waypoints. No flight plans stored in the system
have been modified.
GPS Nav
‘File contained user waypoints only.
User waypoints imported successfully. No stored flight plan data was
modified.’
AFCS
A flight plan file stored on the SD card was successfully
imported as a stored flight plan.
Nav/Com/
XPDR/Audio
‘Flight plan successfully imported.’
Index
Appendix
Annun/
Alerts
Abnormal
Operation
Additional
Features
Hazard
Avoidance
Procedures
Flight
Planning
GPS Nav
AFCS
Nav/Com/
XPDR/Audio
EAS
Flight
Instruments
Annunciations & Alerts
Blank Page
120
Garmin G1000 Cockpit Reference Guide for the Socata TBM 700
190-01247-01 Rev. A
Appendix
Flight
Instruments
APPENDIX
PFD SOFTKEY MAP
EAS
Nav/Com/
XPDR/Audio
AFCS
GPS Nav
Top Level PFD Softkeys
Flight
Planning
METAR
STRMSCP
TRFC-1
Procedures
WX LGND
Additional
Features
Inset Map Softkeys
Level 2
Level 3
Description
Displays Inset Map in PFD lower left corner
INSET
Selects desired amount of map detail; cycles
through declutter levels:
DCLTR (No Declutter): All map features
visible
DCLTR-1: Declutters land data
DCLTR-2: Declutters land and SUA data
DCLTR-3: Removes everything except the
active flight plan
190-01247-01 Rev. A
Garmin G1000 Cockpit Reference Guide for the Socata TBM 700
121
Index
DCLTR (3)
Appendix
Removes Inset Map
Annun/
Alerts
OFF
Abnormal
Operation
Level 1
Hazard
Avoidance
Select the BACK Softkey
to return to the top-level softkeys.
TRFC-2
Level 1
Level 2
Level 3
TRAFFIC
Nav/Com/
XPDR/Audio
AFCS
TOPO
TERRAIN
Displays Stormscope weather and coverage
information on the Inset Map (optional)
Displays NEXRAD weather and coverage
information on Inset Map (optional)
Displays SiriusXM lightning information on
Inset Map (optional)
Displays METAR flags on airport symbols
shown on the Inset Map (optional)
GPS Nav
STRMSCP
Flight
Planning
NEXRAD
XM LTNG
Procedures
Description
Displays icon and age on the Inset Map for
the selected weather products (optional)
Cycles through traffic display options:
TRFC-1: Traffic displayed on inset map
TRFC-2: Traffic Map Page is displayed in
the inset map window
Displays topographical data (e.g.,
coastlines, terrain, rivers, lakes) and
elevation scale on Inset Map
Displays terrain information on Inset Map
WX LGND
EAS
Flight
Instruments
Appendix
Additional
Features
Hazard
Avoidance
METAR
ADC2
Abnormal
Operation
ADC1
AHRS1
BACK
AHRS2
MSG
Select the BACK Softkey to
return to the top level softkeys.
Annun/
Alerts
Sensor Softkeys
Level 2
122
Level 3
Description
ADC1
Displays softkeys for selecting the #1 and
#2 AHRS and Air Data Computers
Selects the #1 Air Data Computer
ADC2
Selects the #2 Air Data Computer
SENSOR
Index
Appendix
Level 1
Garmin G1000 Cockpit Reference Guide for the Socata TBM 700
190-01247-01 Rev. A
Appendix
Level 2
Level 3
Description
AHRS1
Selects the #1 AHRS
AHRS2
Selects the #2 AHRS
Flight
Instruments
Level 1
EAS
ADF/DME
Nav/Com/
XPDR/Audio
SYN VIS
ALT UNIT
HSI FMT
AFCS
Select the BACK Softkey
to return to the top-level softkeys
GPS Nav
METERS
BACK
ARC HSI
IN
Flight
Planning
360 HSI
HPA
Procedures
Hazard
Avoidance
PATHWAY
SYN TERR HRZN HDG APTSIGNS
Additional
Features
PFD Configuration Softkeys
Level 2
Level 3
PFD
190-01247-01 Rev. A
Garmin G1000 Cockpit Reference Guide for the Socata TBM 700
123
Index
SYN TERR
Appendix
PATHWAY
Displays second-level softkeys for
additional PFD configurations
Displays the softkeys for enabling or
disabling Synthetic Vision features
Displays rectangular boxes representing
the horizontal and vertical flight path of
the active flight plan
Enables synthetic terrain depiction
Annun/
Alerts
SYN VIS
Description
Abnormal
Operation
Level 1
Level 1
Level 2
Nav/Com/
XPDR/Audio
EAS
Flight
Instruments
Appendix
AFCS
DFLTS
Flight
Planning
GPS Nav
WIND
Level 3
HRZN HDG Displays compass heading along the
Zero-Pitch line
APTSIGNS Displays position markers for airports
within approximately 15 nm of the
current aircraft position. Airport
identifiers are displayed when the
airport is within approximately 9 nm.
Resets PFD to default settings, including
changing units to standard
Displays softkeys to select wind data
parameters
Wind direction arrows with headwind
OPTN 1
and crosswind components
Wind direction arrow and speed
OPTN 2
Procedures
OPTN 3
Select to display the DME information
window
BRG1
Cycles the Bearing 1 Information
Window through NAV1 or GPS/
waypoint identifier and GPS-derived
distance information.
Displays the HSI formatting softkeys
Displays the HSI in a 360 degree format
Displays the HSI in an arc format
Cycles the Bearing 2 Information
Window through NAV2 or GPS/
waypoint identifier and GPS-derived
distance information.
Displays softkeys for setting the altimeter
and BARO settings to metric units
Abnormal
Operation
HSI FRMT
Annun/
Alerts
360 HSI
ARC HSI
Appendix
BRG2
ALT UNIT
Index
Wind direction arrow with direction
and speed
Information not displayed
DME
Additional
Features
Hazard
Avoidance
OFF
METERS
124
Description
When enabled, displays altimeter in
meters
Garmin G1000 Cockpit Reference Guide for the Socata TBM 700
190-01247-01 Rev. A
Appendix
Level 2
Level 3
Description
Select to display the BARO setting as
inches of mercury
HPA
Select to display the BARO setting as
hectopacals
EAS
IN
Flight
Instruments
Level 1
Nav/Com/
XPDR/Audio
Sets altimeter setting to standard
barometric pressure
STD BARO
AFCS
GPS Nav
MSG
Hazard
Avoidance
Select the BACK Softkey to return
to the top-level softkeys.
Transponder Softkeys
Level 2
Level 3
Description
XPDR2
Selects the #2 transponder as active.
STBY
Selects Standby Mode (transponder does
not reply to any interrogations)
Selects Mode A (transponder replies to
interrogations)
190-01247-01 Rev. A
Garmin G1000 Cockpit Reference Guide for the Socata TBM 700
Index
XPDR1
Displays transponder mode selection
softkeys
Selects the #1 transponder as active.
Appendix
XPDR
Annun/
Alerts
Displays the ADF/DME Tuning Window
Abnormal
Operation
ADF/DME
ON
Additional
Features
Level 1
Procedures
MSG
Flight
Planning
Select the BACK Softkey to return
to the top-level softkeys.
125
Level 1
Level 2
Level 3
Description
0—7
Selects Mode C – Altitude Reporting Mode
(transponder replies to identification and
altitude interrogations)
Manually selects Ground Mode, the
transponder does not allow Mode A
and Mode C replies, but it does permit
acquisition squitter and replies to discretely
addressed Mode S interrogations.
Automatically enters the VFR code (1200 in
the U.S.A. only)
Displays transponder code selection
softkeys 0-7
Use numbers to enter code
BKSP
Removes numbers entered, one at a time
ALT
EAS
Flight
Instruments
Appendix
Nav/Com/
XPDR/Audio
GND
AFCS
VFR
TMR/REF
Activates the Special Position Identification
(SPI) pulse for 18 seconds, identifying the
transponder return on the ATC screen
Displays Timer/References Window
NRST
Displays Nearest Airports Window
MSG
Displays Message Window
IDENT
Index
Appendix
Annun/
Alerts
Abnormal
Operation
Additional
Features
Hazard
Avoidance
Procedures
Flight
Planning
GPS Nav
CODE
126
Garmin G1000 Cockpit Reference Guide for the Socata TBM 700
190-01247-01 Rev. A
Appendix
or
SYSTEM
CPDLC
CAS
(optional)
(optional)
SHW CHRT
CHKLIST
DCLTR-1
CAS↓
EAS
CAS↑
DCLTR
MAP
Flight
Instruments
MFD SOFTKEY MAP
DCLTR-2
TRAFFIC
PROFILE
TOPO
TERRAIN
AIRWAYS
(optional)
(optional)
PRECIP
or
DL LTNG
or
NEXRAD
STRMSCP
XM LTNG
Select the BACK Softkey on this level
to return to the top softkey level.
(optional)
(optional)
(optional)
METAR
LEGEND
WX RADAR
BACK
Nav/Com/
XPDR/Audio
DCLTR-3
AFCS
AIRWY ON
AIRWY LO
GPS Nav
AIRWAY HI
(optional)
SYSTEM
CPDLC
LOGON
LOGOFF
NEW
DELETE
DEL ALL
BACK
CHKLIST
(optional)
CPDLC
MAP
ELEC
+250 FT
-250 FT
+25 FT
FUEL
GEN
CHKLIST
-25 FT
ACCEPT
Flight
Planning
SYSTEM
BACK
Procedures
MFD Softkeys
Level 2
Description
or
CAS
GEN
Displays the General Synoptics Page for the anti-ice
system and doors
When available, accesses CPDLC softkeys.
LOGON
Displays Logon screen for the CPDLC system
LOGOFF
Displays Logoff screen for the CPDLC system
NEW
Accesses New CPDLC message screen
CPDLC
190-01247-01 Rev. A
Garmin G1000 Cockpit Reference Guide for the Socata TBM 700
Index
Displays the Fuel Synoptics Page
Appendix
FUEL
Annun/
Alerts
Scroll up or down (Displayed only when a
sufficient number of items are displayed in the
Crew Alerting System Display to warrant scrolling)
Displays the Electrical Synoptics Page
Abnormal
Operation
CAS ↑
and
CAS ↓
ELEC
Additional
Features
Accesses the Synoptics page softkeys and the
Landing Field Elevation softkeys
SYSTEM
Hazard
Avoidance
Level 1
127
Level 1
EAS
Flight
Instruments
Appendix
Level 2
DELETE
Delete selected CPDLC message.
DEL ALL
Delete all CPDLC messages.
BACK
Returns display to previous softkey level
Enables second-level Navigation Map softkeys
Displays traffic information on Navigation Map
PROFILE
Displays/removes Vertical Situation Display on
Navigation Map Page
Displays topographical data (e.g., coastlines,
terrain, rivers, lakes) and elevation scale on
Navigation Map
Displays terrain information on Navigation Map
AFCS
TRAFFIC
TOPO
GPS Nav
Nav/Com/
XPDR/Audio
MAP
TERRAIN
Hazard
Avoidance
Procedures
Flight
Planning
AIRWAYS
Additional
Features
STRMSCP
NEXRAD
Abnormal
Operation
or
PRECIP
Annun/
Alerts
XM LTNG
or
Appendix
DL LTNG
Index
METAR
128
Description
Displays airways on the map; cycles through the
following:
AIRWAYS: No airways are displayed
AIRWY ON: All airways are displayed
AIRWY LO: Only low altitude airways are
displayed
AIRWY HI: Only high altitude airways are
displayed
Displays Stormscope weather and coverage
information on Navigation Map (optional feature)
Displays NEXRAD weather and coverage information on
the Navigation Map (optional)
Displays Connext precipitation on Navigation Map
(optional)
Displays XM WX lightning information on the
Navigation Map (optional)
Displays Connext Worldwide Weather lightning
information on the Navigation Map (optional)
Displays METAR flags on airport symbols shown on
the Navigation Map
Garmin G1000 Cockpit Reference Guide for the Socata TBM 700
190-01247-01 Rev. A
Appendix
Level 2
Description
Procedures
Appendix
Index
129
Annun/
Alerts
In some cases it may be necessary to obtain an unlock code from Garmin in order
to make the database product functional. It may also be necessary to have the system
configured by a Garmin authorized service facility in order to use some database features.
Abnormal
Operation
NOTE: DO NOT use the database SD cards for any purpose other than database
storage.
Additional
Features
NOTE: When loading database updates, the ‘DB Mismatch’ message will
be displayed until database synchronization is complete, followed by turning
system power off, then on. Synchronization can be monitored on the AUXSYSTEM STATUS Page.
Hazard
Avoidance
CAUTION: Never disconnect power to the system when loading a database.
Power interruption during the database loading process could result in
maintenance being required to reboot the system.
Garmin G1000 Cockpit Reference Guide for the Socata TBM 700
Flight
Planning
UPDATING DATABASES
190-01247-01 Rev. A
GPS Nav
When available, displays optional checklists
AFCS
CHKLIST
Nav/Com/
XPDR/Audio
SHW
CHRT
Selects desired amount of map detail; cycles
through declutter levels:
DCLTR (No Declutter): All map features visible
DCLTR-1: Declutters land data
DCLTR-2: Declutters land and SUA data
DCLTR-3: Removes everything except the active
flight plan
When available, displays optional airport and
terminal procedure charts
DCLTR (3)
EAS
Displays the legend for the selected weather
products. Available only when NEXRAD, XM
LTNG, and/or METAR softkeys are selected.
WX RADAR Displays the weather radar scan on the Navigation
Map (optional)
Returns to top-level softkeys
BACK
LEGEND
Flight
Instruments
Level 1
If an error occurs during synchronization, an error message will be displayed,
followed by the affected display in the Sync Status section of the Database Window. If
synchronization completes on one display, but an error occurs on another, the error
message will be displayed with the affected displays listed after it. When an error message
is displayed, the problem must be corrected before synchronization can be completed.
A power cycle is required to restart synchronization when ‘Card Full’ or ‘Err’ is shown.
Error Message
Description
Canceled
Database synchronization has been canceled by removing the
bottom SD card in display being updated
Card Full
SD card does not contain sufficient memory
Err
Displayed for all other errors that may cause the synchronization
process to be halted
Timeout
System timed-out prior to the database transfer completing
Updating Basemap, SafeTaxi, Airport Terrain, Obstacle, and Airport
Directory Databases
These databases may be copied to one Supplemental Data Card, then automatically
synchronized to other card in the system:
Index
Appendix
Annun/
Alerts
Abnormal
Operation
Additional
Features
Hazard
Avoidance
Procedures
Flight
Planning
GPS Nav
AFCS
Nav/Com/
XPDR/Audio
EAS
Flight
Instruments
Appendix
130
1)
With system power OFF, remove the MFD database card from the bottom
card slot of the MFD.
2)
Update the basemap, SafeTaxi, airport terrain, obstacle and/or airport
directory databases on the MFD card.
3)
Insert the MFD database card into the bottom card slot of the MFD.
4)
Apply power to the system, check that the databases are initialized and
displayed on the power-up screen. If a ‘Verifying’ message is seen, wait for
the system to finish loading before proceeding to step 5.
5)
Acknowledge the Power-up Page agreement by pressing the ENT Key or
the right most softkey.
6)
Turn the large FMS Knob to select the AUX Page group on the MFD.
7)
Turn the small FMS Knob to select the System Status Page.
8)
Monitor the Sync Status in the Database Window. Wait for all databases to
complete synching, indicated by ‘Complete’ being displayed.
9)
Remove and reapply power to the system.
Garmin G1000 Cockpit Reference Guide for the Socata TBM 700
190-01247-01 Rev. A
Appendix
11) Turn the small FMS Knob to select the System Status Page.
Nav/Com/
XPDR/Audio
Updating Terrain, FliteCharts, and ChartView Databases
3)
Insert the updated Supplemental Data Cards into the bottom card slot of
the MFD and PFD. The Supplemental Data Card containing the FliteCharts
or ChartView database is inserted in the MFD.
4)
Apply power to the system, check that the databases are initialized and
displayed on the power-up screen. A ‘Verifying’ message may be seen.
If this message is present, wait for the system to finish loading before
proceeding to step 5.
5)
Acknowledge the Power-up Page agreement by pressing the ENT Key or
the right most softkey.
6)
Turn the large FMS Knob to select the AUX Page group on the MFD.
7)
Turn the small FMS Knob to select the System Status Page.
8)
Press the Display Database Selection Softkey to show database information
for each display (MFD1 DB or PFD1 DB). Verify the correct database cycle
information is shown for each database for each display.
9)
Remove power from the system.
Procedures
Copy the updated terrain database to both Supplemental Data Cards. Copy
the updated FliteCharts or ChartView database to one Supplemental Data
Card.
Hazard
Avoidance
Additional
Features
Abnormal
Operation
Annun/
Alerts
Loading the Jeppesen Navigation Database as the Active Navigation
Database
131
Index
NOTE: Loading the Jeppesen Navigation Database as the active database
prior to its effective date will result in the expiration date on the power-up
screen and the effective date on the AUX-System Status Page being displayed
in yellow.
Appendix
The Jeppesen Navigation Database that is loaded to internal memory as the active
database will be used by the system.
Garmin G1000 Cockpit Reference Guide for the Socata TBM 700
Flight
Planning
2)
GPS Nav
With system power OFF, remove the Supplemental Data Card from the
bottom card slot of the MFD and PFD.
AFCS
1)
190-01247-01 Rev. A
EAS
12) Press the Display Database Selection Softkey to show database information
for each display (MFD1 DB or PFD1 DB). Verify the correct database cycle
information is shown for each database for each display.
Flight
Instruments
10) Turn the large FMS Knob to select the AUX Page group on the MFD.
Flight
Instruments
Appendix
EAS
With the system OFF, insert the SD card containing the new navigation database
version into the top card slot of the display (PFD1, PFD2 or MFD) to be updated
(label of SD card facing left).
2)
Turn the system ON. A prompt is displayed in the upper left corner of the
display:
3)
4)
Press the NO Softkey to proceed to loading the active database.
A prompt similar to the following is displayed. Press the YES Softkey to update
the active navigation database.
5)
After the update completes, the display starts in normal mode.
6)
Turn the system OFF and remove the SD card from the top card slot.
7)
Repeat steps 1 through 6 for the other displays (PFD1, PFD2 or MFD).
8)
Apply power to the system and press the ENT Key to acknowledge the startup
screen.
9)
Turn the large FMS Knob to select the AUX Page group on the MFD.
Index
Appendix
Annun/
Alerts
Abnormal
Operation
Additional
Features
Hazard
Avoidance
Procedures
Flight
Planning
GPS Nav
AFCS
1)
Nav/Com/
XPDR/Audio
NOTE: After the navigation database is loaded or copied, the top SD card
may be removed.
10) Turn the small FMS Knob to select the System Status Page.
132
Garmin G1000 Cockpit Reference Guide for the Socata TBM 700
190-01247-01 Rev. A
Appendix
Nav/Com/
XPDR/Audio
AFCS
The purpose of the Standby Navigation Database is to allow the loading of the
next cycle of the Jeppesen Navigation Database to the bottom SD card, prior to its
effective date. (The Jeppesen Navigation Database is available from Jeppesen seven
days prior to its effective date.)
EAS
Loading the Jeppesen Navigation Database as the Standby Navigation
Database
Flight
Instruments
11) Press the Display Database Selection Softkey to show active navigation
database information for each display (MFD1 DB, PFD1 DB, PFD2 DB). Verify
the correct active navigation database cycle information is shown for each
display.
With the system OFF, insert the SD card containing the new navigation
database version into the top card slot of the MFD.
2)
Verify that an SD card is inserted in the bottom slot of each PFD and the
MFD.
3)
Turn the system ON. A prompt similar to the following is displayed.
4)
Press the YES Softkey. The navigation database is copied to the SD card in
the bottom card slot of the MFD.
Flight
Planning
1)
GPS Nav
NOTE: After the navigation database is loaded or copied, the top SD card
may be removed.
Procedures
Hazard
Avoidance
Additional
Features
Abnormal
Operation
Annun/
Alerts
Appendix
Index
190-01247-01 Rev. A
Garmin G1000 Cockpit Reference Guide for the Socata TBM 700
133
5)
After the navigation database files are copied to the bottom SD card, the
display will appear as shown in the following figure.
6)
As instructed on the display, press any key to continue. The display will now
appear as shown in the following figure.
7)
Press any key to continue. The display will now appear as shown in the
following figure.
8)
Press the NO Softkey. The display now starts in normal mode. Since the
database effective date is not yet valid, it should not be loaded as the
active database. The display now starts in normal mode. Do not remove
power while the display is starting.
9)
Press the ENT Key to acknowledge the startup screen.
Appendix
Annun/
Alerts
Abnormal
Operation
Additional
Features
Hazard
Avoidance
Procedures
Flight
Planning
GPS Nav
AFCS
Nav/Com/
XPDR/Audio
EAS
Flight
Instruments
Appendix
Index
10) Turn the large FMS Knob to select the AUX Page group on the MFD.
11) Turn the small FMS Knob to select the System Status Page.
134
Garmin G1000 Cockpit Reference Guide for the Socata TBM 700
190-01247-01 Rev. A
Appendix
Flight
Instruments
12) The new database is copied to the SD card in the bottom card slot of each
PFD. Progress can be monitored in the SYNC STATUS field. When copying
is finished, ‘Complete’ is displayed.
13) Turn system power OFF.
EAS
14) Remove the SD card from the top card slot of the MFD.
Nav/Com/
XPDR/Audio
15) Turn system power ON.
16) Press the ENT Key to acknowledge the startup screen.
17) Turn the large FMS Knob to select the AUX Page group on the MFD.
Flight
Planning
Procedures
To manually activate the standby navigation database:
1) From the AUX-SYSTEM STATUS Page, select the STANDBY DB Softkey.
2) A prompt similar to the following figure below is displayed, select ‘Yes’
to overwrite the Active Navigation Database with the Standby Navigation
Database. Select ‘No’ to cancel.
GPS Nav
19) Press the Display Database Selection Softkey to show standby navigation
database information for each display (MFD1 DB, PFD1 DB, PFD2 DB).
Verify the correct standby navigation database cycle information is shown
for each display.
AFCS
18) Turn the small FMS Knob to select the System Status Page.
Hazard
Avoidance
Additional
Features
Abnormal
Operation
Annun/
Alerts
Standby Nav Database Activation Confirmation Window
Appendix
Index
190-01247-01 Rev. A
Garmin G1000 Cockpit Reference Guide for the Socata TBM 700
135
Loading the magnetic field variation database update:
A copy of the current magnetic field variation database (MV DB) is included with
the navigation database. At startup, the system compares this version of the MV
DB with that presently being used by each AHRS (GRS1 and GRS2). If the system
determines the MV DB needs to be updated, a prompt is displayed on the Navigation
Map Page, as shown in the following figure.
GPS Nav
AFCS
Nav/Com/
XPDR/Audio
EAS
Flight
Instruments
Appendix
GRS1 Magnetic Field Variation Database Update Prompt
With ‘OK’ highlighted, press the ENT Key on the MFD. A progress monitor
is displayed.
Additional
Features
Hazard
Avoidance
Procedures
Flight
Planning
1)
Abnormal
Operation
Uploading Database to GRS1
When the upload is complete, the prompt for the next GRS upload is
displayed.
Index
Appendix
Annun/
Alerts
2)
GRS2 Magnetic Field Variation Database Update Prompt
136
Garmin G1000 Cockpit Reference Guide for the Socata TBM 700
190-01247-01 Rev. A
Appendix
With ‘OK’ highlighted, press the ENT Key on the MFD. A progress monitor
is displayed. When the upload is complete, the system is ready for use.
Flight
Instruments
3)
EAS
Nav/Com/
XPDR/Audio
AFCS
Uploading Database to GRS2
GPS Nav
Flight
Planning
Procedures
Hazard
Avoidance
Additional
Features
Abnormal
Operation
Annun/
Alerts
Appendix
Index
190-01247-01 Rev. A
Garmin G1000 Cockpit Reference Guide for the Socata TBM 700
137
Index
Appendix
Annun/
Alerts
Abnormal
Operation
Additional
Features
Hazard
Avoidance
Procedures
Flight
Planning
GPS Nav
AFCS
Nav/Com/
XPDR/Audio
EAS
Flight
Instruments
Appendix
Blank Page
138
Garmin G1000 Cockpit Reference Guide for the Socata TBM 700
190-01247-01 Rev. A
Index
Procedures
E
Hazard
Avoidance
Edit a flight plan 40
Enable Terrain 56
Essential bus voltage 6
Additional
Features
F
Index
Index-1
Appendix
Garmin G1000 Cockpit Reference Guide for the Socata TBM 700
Annun/
Alerts
Flap position 6
Asymmetrical deflection warning 91
Flight Director 21
Flight ID 13
Flight path marker 63
FliteCharts® 64, 65
Frequency Transfer 14
Fuel
Alerts 91–92
Flow 6
Pressure 6
Quantity 6
Abnormal
Operation
190-01247-01 Rev. A
Flight
Planning
Cabin pressure altitude 6
Warning 91
CDI 1, 2, 14, 116
Cell 47, 48
Data link communication 15
DB Mismatch 129
DCLTR Softkey 65
Dead Reckoning 88
Declutter 88, 121, 129
Designated altitudes 28
Differential cabin pressure 6
Warning 91
Direct-to 25
DME 13, 14
Door status 11
DR mode 88, 89, 90
GPS Nav
C
D
AFCS
Barometric Altitude Minimums 3
Battery
Alerts 92
Current 6
Overheat warning 91
Voltage 6
Bearing line 60, 62
Nav/Com/
XPDR/Audio
B
EAS
Activate a flight plan 26
Active Channel 67
Active database 132
Active Navigation Database 131
ADF 13, 14, 88
AHRS 109, 110, 111, 113, 114
Airport Signs 63, 64
Airways 128
Air Data Computer 93
Alert messages 112
ALT 53
Altimeter setting 1, 88
Altitude mode 53
Altitude volume 53
Antenna stabilization 62
Antenna tilt 60
AOPA’s Airport Directory 66
ATC 15, 16, 17
Attitude & Heading Reference System
93
Audio panel controls
NAV1, NAV2 14
Cell mode 48
Channel Presets 68
ChartView 64, 65
Code selection softkeys 14
COM 14, 87
CPDLC 15, 16, 17, 18
Flight
Instruments
A
Index
Appendix
Annun/
Alerts
Abnormal
Operation
Additional
Features
Hazard
Avoidance
Procedures
Flight
Planning
GPS Nav
AFCS
Nav/Com/
XPDR/Audio
EAS
Flight
Instruments
Index
G
Gain 61
Generator
Current 6
Speed 6
Ground mapping 61
H
HF 14
Horizontal scan 61
Horizon heading 63
I
Inhibit 55, 57
Inhibit TAWS 57
Inhibit Terrain 55
Inset Map 121, 122, 128
Interturbine Temperature (ITT) 6
Warning 91
IOI 95, 97, 98
Iridium 69, 72
Iridium satellite network 69
Minimums 99
MISCOMP 93
Mode S 126
Mode selection softkeys 14
Multi Function Display (MFD)
Softkeys 127
N
NAV 14
NAV1 2, 14
NAV2 2, 14
Navigation database 27, 28
NEXRAD 49, 122, 128
O
J
OBS 2
Obstacles 104, 106
Oil, engine
Alerts 91
Pressure 6
Temperature 6
Overspeed Protection 22
Oxygen
Warning 91
Jeppesen 65
P
L
Pathways 63, 64
PIT 93
Predefined message 75
Propeller speed 6
Lightning 47, 48
M
Map panning 49
Message advisories 100, 101, 104,
109, 111, 113, 114, 115
Message dialogs 17, 18
Messages window 83
METAR 49
Index-2
R
Response/Request 17
Reversionary Mode
EICAS 5
Reversionary mode 87
ROC 95, 97
Garmin G1000 Cockpit Reference Guide for the Socata TBM 700
190-01247-01 Rev. A
Index
Nav/Com/
XPDR/Audio
V
AFCS
Vertical speed guidance 28
Vertical track 99
Video settings 81
VNV 25, 88, 117
Vspeed 2
GPS Nav
W
Abnormal
Operation
Annun/
Alerts
Appendix
Index
Garmin G1000 Cockpit Reference Guide for the Socata TBM 700
Additional
Features
XM lightning 122
XM weather 49
XM WX lightning 128
Hazard
Avoidance
TA 99
TAF 49
TAS 53, 99, 109
TAWS 56, 57, 58, 97
TAWS-B 56
Telephone 69, 71, 72, 74, 76
Terrain 54, 56, 104, 122, 128
Terrain-SVS 54, 55, 56
Text message 73, 75, 76
Text messaging 72
Tilt line 60
Timer 2, 115
Topographical data 122, 128
Torque 6
Warning 91
Traffic 47, 52, 128
Procedures
X
Flight
Planning
WATCH® 62
Waypoint Selection Submenu 36
Weather Attenuated Color Highlight 62
Weather data link page 49
Weather radar 59
Wind data 124
T
190-01247-01 Rev. A
EAS
SafeTaxi® 64
SBAS 22, 44, 56, 57, 89, 106, 107
Scheduler 82
SD Card 85, 86, 129, 130, 132, 133,
134, 135
Sector scan 62
Sensor 93
SMS 69
STAB 62
Standby 59
Standby Navigation Database 133, 135
Store Flight Plan 39
Stormscope lightning data 47, 48
Strike 47
Strike mode 48
Supplemental Data Card 130, 131
SVS 63, 118
Synchronization 130
Synthetic Vision System 63
Traffic advisory 52
Traffic Advisory 99
Traffic map page 52, 53, 54
Transponder 13, 14, 125, 126
Trim 6
Flight
Instruments
S
Index-3
Index
Appendix
Annun/
Alerts
Abnormal
Operation
Additional
Features
Hazard
Avoidance
Procedures
Flight
Planning
GPS Nav
AFCS
Nav/Com/
XPDR/Audio
EAS
Flight
Instruments
Index
Blank Page
Index-4
Garmin G1000 Cockpit Reference Guide for the Socata TBM 700
190-01247-01 Rev. A
Garmin International, Inc.
1200 East 151st Street
Olathe, KS 66062, U.S.A.
p: 913.397.8200 f: 913.397.8282
Garmin AT, Inc.
2345 Turner Road SE
Salem, OR 97302, U.S.A.
p: 503.391.3411 f: 503.364.2138
Garmin (Europe) Ltd
Liberty House, Hounsdown Business Park
Southampton, SO40 9LR, U.K.
p: 44 (0) 23 8052 4000 f: 44 (0) 23 8052 4004
Garmin Corporation
No. 68, Jangshu 2nd Road
Shijr, Taipei County, Taiwan
p: 886/2.2642.9199 f: 886/2.2642.9099
www.garmin.com
© 2010, 2014, 2015 Garmin Ltd. or its subsidiaries
190-01247-01 Rev. A
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising