Siemens | EH475MG11E | Instruction manual | Siemens iQ100 Electric cooktop Instruction manual

Siemens iQ100 Electric cooktop Instruction manual
EH3..ME1..
[en] Instruction manual .............................................................. 2
*9000308580*
9000308580
(+0(
‘
‘
Ú Table of contents
Safety warnings and advice ...................................................... 3
Safety instructions...............................................................................3
Elements that may damage the appliance ....................................3
Protecting the environment....................................................... 4
Environmentally-friendly disposal of waste products ...................4
Energy-saving advice .........................................................................4
Induction cooking ...................................................................... 4
Advantages of induction cooking ....................................................4
Suitable pans.......................................................................................4
Familiarise yourself with the appliance.................................... 5
The control panel ................................................................................5
The hotplates .......................................................................................5
Residual heat indicator ......................................................................5
Programming the hob ............................................................... 6
Switching the hob on and off ...........................................................6
Setting the hotplate ............................................................................6
Cooking guidelines.............................................................................6
The Powerboost Function ......................................................... 8
Use limitations ..................................................................................... 8
To activate............................................................................................ 8
To turn off............................................................................................. 8
Time programming function ..................................................... 8
Turning off a hotplate automatically ................................................ 8
Automatic timer ................................................................................... 8
The timer .............................................................................................. 9
Automatic time limitation .......................................................... 9
Basic settings............................................................................. 9
To access the basic settings......................................................... 10
Care and cleaning .................................................................... 10
Hob..................................................................................................... 10
Hob frame ......................................................................................... 10
Fixing malfunctions ................................................................ 10
Normal noise while the appliance is working ............................ 11
After-sales service ................................................................... 11
Produktinfo
Additional information on products, accessories, replacement
parts and services can be found at www.siemens-home.com
and in the online shop www.siemens-eshop.com
2
Ø = cm
ã=Safety warnings and advice
Please read these instructions carefully. We advise you not to
use the appliance until you have read them.
The hotplate heats up, but the display does not work
Keep the operation and installation instructions. If the appliance
is passed on to another user, please ensure that the
documentation is also passed on with it.
Turn off the hotplate if the indicator does not work. Contact the
Technical Assistance Service.
Check the appliance after removing it from the packaging. If it
has suffered any damage in transport, do not connect the
appliance, contact the Technical Assistance Service and
provide written notification of the damage caused, otherwise
you will lose your right to any type of compensation.
Safety instructions
Risk of burns!!
The hob switches off
Risk of fire!!
If the hob switches off automatically and cannot be used, it can
subsequently switch on by itself. To avoid this the hob must be
disconnected from the mains. Please contact the Technical
Assistance Service.
This device has been designed exclusively for home use. Only
use the hob for food preparation. The appliance must not be
left unsupervised while in use.
Do not place metal objects on the induction hotplate
Safe operation
Do not leave knives, forks, spoons, lids or other metal objects
that can heat up very quickly on the hob.
To use this appliance safely, adults and children who, as a
result of
■
physical, sensory or mental disability,
■
or lack of experience or knowledge,
are not capable of using this appliance, should not do so
without the supervision of a responsible adult.
Children must be supervised to ensure that they do not play
with the appliance.
Oil and fat too hot
Risk of fire!!
Oil or fat that is too hot quickly catches fire. Do not leave
overheated oil or fat unwatched. If the oil or fat catches fire,
never use water to put it out. Extinguish the flames with a lid or
a plate. Switch off the hotplate.
Cooking food using the bain-marie method
The bain-marie method allows you to cook food in a saucepan
submerged in a larger pan containing water. The water cooks
the food with a gentle and constant heat, rather than directly
from the heat of the hotplate. When cooking food in bain-marie,
you must prevent tins, glass containers or other material from
resting directly on the base of the pan containing the water, to
prevent the glass on the hob and the pan from breaking due to
hotplate reheating.
Risk of burns!!
Fan care
Malfunction risk!
The bottom of the hob is equipped with a fan. If there is a
drawer under the hob it should not be used to store small
objects or paper, since they could damage the fan or interfere
with the cooling if they are sucked into it.
Caution!
There should be a minimum distance of 2 cm between the
drawer and the fan entrance.
Incorrect repairs
Risk of electric shock!!
Poor repairs are dangerous. Switch off the appliance if it is
faulty. Contact the Technical Assistance Service. Repairs and
the replacement of faulty connection cables may only be
performed by qualified personnel from the Technical
Assistance Service.
Caution!
Do not touch hot hotplates. Keep children away from the hob.
This appliance complies with safety and electromagnetic
compatibility standards. However, people with pacemakers
must refrain from approaching the appliance when in use. It is
impossible to ensure that all of these devices available on the
market comply with current electromagnetic compatibility
standards, and that interference which may prevent the device
from working correctly will not occur. It is also possible that
people with other types of devices, such as a hearing aids,
could experience some discomfort.
Risk of fire!!
Switching off the hob
Hot hob
Risk of burns!!
■
■
Never place flammable objects on the hob
Do not keep flammable items or aerosols in the drawers
beneath the hob.
After each use, always turn off the hob at the main switch. Do
not wait until the hob turns off automatically after the pan is
removed.
Wet hotplates and pan bases
Elements that may damage the appliance
Risk of injury!!
Caution!
Liquid between the bottom of the pan and the hob can produce
steam pressure. Which may cause the pan to jump. Always
ensure that the hotplate and the base of the pan are kept dry.
Cracks in the hob
Risk of electric shock!!
Disconnect the appliance from the mains if the hob is broken or
cracked.
Contact the Technical Assistance Service.
■
■
■
■
■
Rough pan bases may scratch the hob.
Avoid leaving empty pots and pans on the hotplate. Doing so
may cause damage.
Do not place hot pans on the control panel, the indicator
area, or the hob frame. Doing so may cause damage.
Hard or pointed objects dropped on the hob may damage it.
Aluminium foil and plastic containers will melt if placed on the
hotplate while it is hot. The use of laminated sheeting is not
recommended on the hob.
3
Overview
The following table presents the most common damage
caused:
Damage
Cause
Measure
Stains
Food spillage
Immediately remove spilt food using a glass scraper.
Unsuitable cleaning products
Only use cleaning products specifically designed for glass-ceramic hobs.
Scratches
Salt, sugar and sand
Do not use the hob as a tray or working surface.
Pans with rough bottoms may scratch Check pans.
the glass ceramic
Fading
Unsuitable cleaning products
Only use cleaning products specifically produced for glass-ceramic hobs.
Contact with pans
Lift pots and pans before moving them around.
Chips
Sugar, substances with a high sugar Immediately remove spilt food using a glass scraper.
content
Protecting the environment
Unpack the appliance and dispose of its packaging in such a
way that no damage is caused to the environment.
■
■
Environmentally-friendly disposal of waste
products
This appliance conforms to the Waste Electrical and
Electronic Equipment Directive WEEE 2002/96/EC.
This directive defines the framework for recycling used
appliances within European territory
■
Energy-saving advice
■
Always place the correct lid on the pan. Cooking with an
uncovered pan will result in a four-fold increase in energy
use.
■
Use pans equipped with a solid, flat bottom. Curved pan
bases increase energy consumption.
The diameter of the pan base must coincide with the
diameter of the hotplate. This generally means the pan base
diameter is greater than that of the hotplate. If the diameter of
the pan is not the same as the diameter of the hotplate, it is
preferable to use a pan with a bottom that is larger in
diameter than the hotplate, otherwise half the energy will be
wasted. Please note: Whether the cookware manufacturer
has indicated the diameter of the top of the pan.
Choose pans of a size suited to the amount of food you are
going to cook. A large pan that is only half full will use a great
amount of energy.
Use a small amount of water when cooking. This saves
energy, and vegetables retain their vitamins and minerals.
■
Select a lower power level.
■
special cutlery for stainless steel induction pan
Induction cooking
Advantages of induction cooking
Induction cooking represents a radical change from the
traditional method of heating; the heat is generated directly in
the pan. It therefore offers a number of advantages:
■
■
■
■
Time savings for cooking and frying; since the pan is heated
directly.
Energy is saved.
Care and cleaning are simpler. Foods that have spilt do not
burn as quickly.
Heat and safety control; the hob supplies or cuts off power
immediately when the control knob is turned on. The
induction hotplate stops supplying heat if the pan is removed
without having previously switched it off.
Suitable pans
Ferromagnetic pans
Only ferromagnetic pans are suitable for induction cooking,
these may be made from:
■
enamelled steel
■
cast iron
4
To determine whether a pan is suitable, check to see if a
magnet will stick to it.
Special induction pans
There is another type of pan specially made for induction, the
base of which is not entirely ferromagnetic. Check the diameter,
since this could affect detection of the pan, as well as the
cooking results.
Unsuitable pans
Never use pans made from:
■
common thin steel
■
glass
■
earthenware
■
copper
■
aluminium
Characteristics of the pan base
The characteristics of the pan base may affect the uniformity of
the cooking results. Pans made from materials which help
diffuse heat, such as stainless steel sandwich pans, distribute
heat uniformly, saving time and energy.
pan and switch the hotplate off. If it fails to work after it has
cooled down, please contact the Technical Assistance Service.
Absence of pan or unsuitable size
If no pan is placed on the selected hotplate, or if it is made of
unsuitable material or is not the correct size, the power level
displayed on the hotplate indicator will flash. Place a suitable
pan on the hotplate to stop the flashing. If this takes more than
90 seconds, the hotplate will switch off automatically.
Pan detection
Each hotplate has a minimum limit for detecting pans, which
varies depending on the material of the pan being used. You
should therefore use the hotplate that is most suitable for the
diameter of your pan.
Empty pans or those with a thin base
Do not heat empty pans, nor use pans with a thin base. The
hob is equipped with an internal safety system. However, an
empty pan may heat up so quickly that the "automatic switch
off" function may not have time to react and the pan may reach
very high temperatures. The base of the pan could melt and
damage the glass on the hob. In this case, do not touch the
Double or triple hotplate
These hotplates can detect pans of different sizes. Depending
on the material and properties of the pan, the hotplate will
adapt automatically, switching on part or all of the hotplate and
supplying sufficient power to obtain good cooking results.
Familiarise yourself with the appliance
These instructions for use are applicable to other hobs. On
page 2 an overview of the models is provided, along with
information on measurements.
The control panel
,QGLFDWLRQVIRU
SRZHUOHYHO³É
IXQFWLRQDOLW\¯
UHVLGXDOKHDW‡¤
SRZHUERRVWIXQFWLRQ°
&RQWUROSDQHO
IRU
PDLQVZLWFK
WRVHOHFWWKH
FRRNLQJ]RQH
,QGLFDWLRQVIRU
WLPH
SURJUDP
IXQFWLRQ
&RQWUROSDQHOIRU
WLPHSURJUDP
IXQFWLRQ
3URJUDPPLQJSDQHOIRU
SRZHUOHYHOVHOHFWLRQ
DQGWLPHSURJUDPIXQFWLRQ
Control surfaces
Pressing a symbol activates its corresponding function.
Notes
The settings will not change if several symbols are pressed at
the same time. This enables the programming zone to be
cleaned when food is spilt.
■
■
Always keep the control surfaces dry. Moisture can affect
proper functioning.
The hotplates
Hotplate
Turning on and off
$ Single hotplate
Always use cookware of a suitable size.
Use only cookware suitable for induction cooking; see the section on suitable cookware.
Residual heat indicator
The hob has a residual heat indicator for each hotplate to show
those which are still hot. Avoid touching a hotplate that displays
this.
Even when switched off, the œ/• light will remain on as long as
the hotplate remains hot.
If the pan is removed before the hotplate is turned off the œ/•
indicators and the selected power level will appear alternately.
5
Programming the hob
This section will show you how to program the hotplates. The
table contains power levels and cooking times for several
dishes.
Switching the hob on and off
The hob is turned on and off with the main switch.
To switch on: press the # symbol. The indicator above the
main switch lights up. The hob is ready for use.
Selecting the power level
The hob must be switched on.
1. Press the ¤ symbol of the desired hotplate. The ‹ and N
symbols light up in the display.
2. Within the next 10 seconds, slide a finger on the
programming panel until the desired power level lights up.
To switch off: press the # symbol until the indicator above the
main switch disappears. All hotplates are off. The residual heat
indicator stays on until the hotplates have cooled down
completely.
Note: The hob switches off automatically when all the hotplates
are switched off for more than 20 seconds.
Setting the hotplate
The desired power level is set in the programming panel.
Power level 1 = minimum power.
Power level 9 = maximum power.
Each power level has an intermediate setting. This is marked
with a dot.
3. To change the power level, select the hotplate and set the
desired level using the programming panel.
Switch off the hotplate
Select the hotplate and set it to ‹ in the programming panel.
The hotplate turns off and the residual heat indicator appears.
Notes
■ Upon selecting a hotplate the N symbol is displayed. It may
then proceed to be adjusted.
■
If no pan has been placed on the induction hotplate, the
selected power level flashes. After a certain time has
elapsed, the hotplate switches off.
Cooking guidelines
The table below contains some examples.
The cooking times depend on the power level, type, weight and
quality of the food. As such they are approximate.
Remove purées, creams and thick sauces from time to time, if
they get too hot.
Use power level 9 to begin cooking.
Power levels influence the cooking results.
Ongoing cooking
setting
Ongoing cooking time
in minutes
Chocolate, chocolate coating, butter, honey
1-1.
-
Gelatine
1-1.
-
Stew (e.g., lentils)
1-2
-
Milk**
1.-2.
-
Sausages heated in water**
3-4
-
Frozen spinach
2­-3
5-15 min
Frozen goulash
2­-3
20-30 min
Potato pancakes
4­-5*
20-30 min
Fish
4 -5*
10-15 min
White sauces (e.g., bechamel)
1-2
3-6 min
Whipped sauces (e.g., Bearnaise, Hollandaise)
3-4
8-12 min
Melt
Heating and warming
Defrosting and heating
Slow cooking, simmering
* Continue cooking without a lid
** Uncovered
6
Ongoing cooking
setting
Ongoing cooking time
in minutes
Rice (with a double amount of water)
2-3
15-30 min
Rice pudding
2-3
25-35 min
Unpeeled potatoes
4-5
25-30 min
Peeled potatoes with salt
4-5
15-25 min
Pasta
6 -7*
6-10 min
Soups
3­-4
15-60 min
Vegetables
2­-3
10-20 min
Greens, frozen foods
3­-4
7-20 min
Cooked in a pressure cooker
4­-5
-
Meat roll
4-5
50-60 min
Roast
4-5
60-100 min
Goulash
3­-4
50-60 min
Steaks, plain or breaded
6-7
6-10 min
Frozen steaks
6-7
8-12 min
Chops, plain or breaded
6-7
8-12 min
Beefsteak (3 cm thick)
7-8
8-12 min
Chicken breast (2 cm thick)
5-6
10-20 min
Frozen chicken breast
5-6
10-30 min
Fish and fish fillet without breading
5-6
8-20 min
Fish and fish fillet with breading
6-7
8-20 min
Frozen breaded fish (e.g., fish fingers)
6-7
8-12 min
Prawns and shrimps
7-8
4-10 min
Frozen meals (e.g., stir-fries)
6-7
6-10 min
Crepes
6-7
fry one portion at a time
Omelette
3­-4
fry one portion at a time
Fried eggs
5-6
3-6 min
Frozen foods (e.g., French fries, chicken nuggets)
8-9
fry one portion at a time
Frozen croquettes
7-8
Meatballs
7-8
Meat (e.g., chicken pieces)
6-7
Fish, in breadcrumbs or batter
6-7
Greens, mushrooms, in breadcrumbs or batter (e.g., baby mushrooms)
6-7
Confectionary products (e.g., fritters, fruit in batter)
4-5
Boiling, steaming, roasting
Roasting
Broil**
Frying** (150-200g per serving with 1-2 l. of oil)
* Continue cooking without a lid
** Uncovered
7
The Powerboost Function
The Powerboost function can be used to heat food more
quickly than using the power level Š.
To activate
Use limitations
2. Press the programming panel located above the @› symbol.
The function has been activated.
This function is available on all hotplates, provided that no other
hotplate in the same group is operating, (see diagram).
Otherwise, the › and Š symbols will flash on the display of the
selected hotplate; then the power level is automatically set Š.
In model 1, the powerboost function may be activated at the
same time for all hotplates (see picture).
0RGHO
1. Select the power level Š.
To turn off
Press the programming panel located above the @› symbol.
The Powerboost function has been deactivated.
Note: In certain circumstances, the Powerboost function may
turn off automatically in order to protect the electronic
components inside the hob.
0RGHO
0RGHO
Time programming function
This function may be used in two different ways:
■
to automatically switch off a hotplate.
■
as a timer.
Turning off a hotplate automatically
Enter the cooking time for the required hotplate. The hotplate
turns off automatically once the time has elapsed.
How to program
1. Select the required power level.
2. Press the 0 symbol. The x indicator of the hotplate lights
up. ‹‹ is displayed in the time program function display. To
select another hotplate, press the 0 symbol several times
until the x indicator for the desired hotplate lights up.
3. Select the required cooking time in the programming panel.
The possible previous setting is, from left to right 1, 2, 3, etc.,
up to 10 minutes. Within the next 10 seconds, continue
passing through the options in the programming panel until
reaching the desired time.
Automatic programming
If the previous setting from 1 to 5 is pressed in the
programming panel, the cooking time is reduced by one
minute, if it is held down the time is automatically reduced to
one minute.
If the previous setting from 6 to 10 is pressed in the
programming panel , the cooking time is increased by one
minute, if it is held down the time is automatically increased to
99 minutes.
Once the time has elapsed
The hotplate switches off. An audible signal sounds and ‹‹
appears in the time program function display for 10 seconds.
Thex indicator lights up. Pressing the 0 symbol turns off the
indicators and stops the signal.
Changing or cancelling the time
Select the hotplate and then press the symbol 0. Change the
cooking time using the programming panel or set to ‹‹.
Notes
■ If a cooking time has been programmed in several zones, it
can be set to display all time values. To do this, press the 0
symbol several times until the x indicator for the required
hotplate lights up.
■
Cooking times of up to 99 minutes can be programmed.
Automatic timer
With this function you may select a cooking time for all
hotplates. Once a hotplate is switched on, the selected time will
begin to count down. The hotplate will automatically switch off
when the cooking time has elapsed.
After a few seconds, the cooking time begins to count down.
Instructions on activating the timer are found in the chapter
entitled "Basic settings".
Note: The cooking time of a zone may be cancelled or
changed:
Press the 0 symbol several times until the required x
indicator lights up. Change the cooking time in the
programming panel, or set to ‹‹.
8
The timer
Once the time has elapsed
The timer can be set for periods of up to 99 minutes. It is
independent of the other settings. This function does not
automatically switch off a hotplate.
‹‹ is shown, and the W indicator comes on. After 10 seconds
Programming
Pressing the 0 symbol turns off the indicators and stops the
beep.
1. Press the 0 symbol several times until the W indicator lights
up. ‹‹ lights up in the time program function display.
2. Select the desired time in the programming panel.
The timer starts to count down after a few seconds.
A warning beep sounds. In the time program function display
the indicators turn off.
Changing or cancelling the time
Press the 0 symbol several times until the W indicator lights
up. Change the cooking time in the programming panel, or set
to ‹‹.
Automatic time limitation
If the hotplate remains in use for a long time and no changes
are made in the settings, the automatic time limitation function
is triggered.
The hotplate stops heating. On the hotplate display, ”and ‰
flash alternately.
The indicator goes out when any symbol is pressed. The
hotplate can now be reset.
When the automatic time function is used, it is governed by the
selected power level (from 1 to 10 hours).
Basic settings
The device has several basic settings. These settings may be
adapted to the needs of the user.
Indicator
Function
™ƒ
Beeps
‹ Most signals deactivated.
‚ Some beeps deactivated.
ƒ All beeps activated.*
™†
Automatic timer
‹ Switched off.*
‚-ŠŠ Automatic shut-off time
™‡
Duration of the time program function warning signal
‚ 10 seconds*.
ƒ 30 seconds.
„ 1 minute.
™ˆ
Power-Management function
‹ = Deactivated.*
‚ = 1,000 W minimum power.
‚. = 1,500 W.
ƒ = 2,000 W.
etc.
Š or Š. = maximum power of the hob.
™Š
Hotplate time selection
‹ Unlimited: the last hotplate programmed remains selected.*
‚ limited: The hotplate will only remain selected for 10 seconds.
™‹
Return to default settings
‹ Personal settings.*
‚ Return to factory settings.
*Factory settings
9
To access the basic settings
3. Press the 0 symbol several times until the indicator for the
desired function appears on the left of the screen.
The hob must be turned off.
4. Then select the desired setting in the programming panel.
1. Turn on the hob with the main switch.
2. Within the next 10 seconds, press the 0 symbol and hold for
4 seconds.
5. Press the 0 symbol again and hold for more than 4
seconds.
™ƒ is displayed on the left of the screen and ‹ on the right.
The settings will have been correctly saved.
Quit
To leave the basic settings, turn off the hob at the main switch.
Care and cleaning
The advice and warnings contained in this section aim to guide
you in cleaning and maintaining the hob, so that it is kept in the
best possible condition
Hob
1. Release the scraper safety catch
2. Use the blade to clean the hob surface
Do not attempt to clean the hob surface with the base of the
scraper. This could result in scratching.
ã=Risk of injury!!
Cleaning
Clean the hob after each use. This prevents food remains left
on the surface from burning. Wait until the hob is cold enough
before attempting to clean it.
Only use cleaning products specifically designed for glassceramic hobs. Follow the instructions provided on the
packaging.
Care of the appliance
Apply an additive to protect and preserve the hob. Follow the
advice and warnings provided with the product.
Do not use:
■
Abrasive products
■
heavy-duty cleaners, like oven sprays and stain removers
■
Pads that may scratch
■
High-pressure or steam cleaners
The blade is extremely sharp. Risk of cuts. Protect the blade
when not in use. Replace the blade immediately when any
imperfections are found.
Hob frame
In order to avoid damage to the hob frame, follow the
indications below:
Glass scraper
■
Use only slightly soapy hot water
■
Do not use sharp or abrasive products
■
Do not use a glass scraper
Remove dried-on food remains using a glass scraper.
Fixing malfunctions
Malfunctions are generally caused by minor faults. Before
contacting the Technical Assistance Service, make sure you
have read the following recommendations and warnings.
Indicator
Malfunction
Measure
none
The electric power supply has been
interrupted.
Use other electrical appliances to check if there has been a power
cut.
The appliance has not been correctly
connected following the connection
diagram.
Make sure that the appliance has been connected correctly.
Electronic system malfunction.
If in the above checks, the malfunction is not resolved, contact the
Technical Assistance Service.
* If the warning persists call the Technical Assistance Service.
Do not place hot pans on the control panel.
10
Indicator
Malfunction
Measure
“ flashing
The control panel is wet or an object is
resting on it.
Dry the control panel area or remove the object.
Ҥ + number / Electronic system malfunction.
š + number /
¡ + number
Disconnect the hob from the mains. Wait 30 seconds or so, then
connect it again.*
”‹ / ”Š
There is an internal error in the system.
Disconnect the hob from the mains. Wait 30 seconds or so, then
connect it again.*
”ƒ
The electronic system has overheated and Wait until the electronic system has cooled down completely. Then
the corresponding hotplate has been
press any symbol on the hob.*
switched off.
”…
The electronic system has overheated and
all hotplates have been switched off.
—‚
Supply voltage outside normal operating
limits.
—ƒ / —„
The hotplate has overheated and switched Wait until the electronic system has cooled down sufficiently before
off to protect its working surface.
switching it back on.
Please contact the local electricity board.
* If the warning persists call the Technical Assistance Service.
Do not place hot pans on the control panel.
Normal noise while the appliance is working
Induction heating technology is based on the creation of
electromagnetic fields that generate heat directly at the base of
the pan. Depending on how the pan has been manufactured,
these may produce certain noises or vibrations such as those
described below:
A deep humming sound as in a transformer
This noise is produced when cooking on a high power level. It
is caused by the amount of energy transferred from the hob to
the pan. The noise disappears or becomes faint when the
power level is lowered.
A low whistling sound
This noise is produced when the pan is empty. It disappears
when water or food is added to the pan.
A crackling soolund
This noise occurs in pans which are made from different
materials superimposed on one another. It is caused by the
vibrations that occur ajoining surfaces of the different
superimposed materials. The noise comes from the pan. The
amount of food and cooking method can vary.
A high-pitched whistling sound
This noise is produced mainly in pans made from different
materials superimposed on one another, and it occurs when
such pans are heated at maximum power on two hotplates at
the same time. The whistling disappears or becomes fainter as
soon as the power level is lowered.
Noise from the fan
For proper use of the electronic system, the temperature of the
hob must be controlled. For this purpose, the hob has a fan
that starts working after detecting excess temperatures at
different power levels. The fan may also work due to inertia
after the hob has been switched off, if the temperature detected
is still too high.
The noises described are normal, they are part of induction
heating technology and not a sign of malfunction.
After-sales service
Our after-sales service is there for you if your appliance should
need to be repaired. We are committed fo find the best solution
also in order to avoid an unnecessary call-out.
E number and FD number:
Please quote the E number (product number) and the FD
number (production number) of your appliance when
contacting the after-sales service. The rating plate bearing
these numbers can be found on the appliance certificate.
Please note that a visit from an after-sales service engineer is
not free of charge, even during the warranty period.
To book an engineer visit and product advice
GB
0844 8928999
Calls from a BT landline will be charged at up to
3 pence per minute. A call set-up fee of up to 6 pence
may apply.
IE
01450 2655
Trust the expertise of the manufacturer, and rest assured that
the repair will be carried out by trained service technicians
using original spare parts for your domestic appliance.
Please find the contact data of all countries in the enclosed
customer service list.
11
Siemens-Electrogeräte GmbH
Carl-Wery-Straße 34
81739 München
DEUTSCHLAND
(901015)
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising