Siemens | EZ877KZY1E | Instruction manual | Siemens iQ700 Electric cooktop Instruction manual

Siemens iQ700 Electric cooktop Instruction manual
Full surface induction cooktop
EZ8..KZ...
en Instruction manual
en
Table of contents
enI nst r uct i on manual
8 Intended use . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
( Important safety information . . . . . . . . . . . . . . . 6
] Causes of damage . . . . . . . . . . . . . . . . . . . . . . . . 8
Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
7 Environmental protection . . . . . . . . . . . . . . . . . . 9
Tips for saving energy . . . . . . . . . . . . . . . . . . . . . . . . . 9
Environmentally-friendly disposal . . . . . . . . . . . . . . . . . 9
f Induction cooking . . . . . . . . . . . . . . . . . . . . . . . . 9
Advantages of induction cooking . . . . . . . . . . . . . . . . . 9
Cookware. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
* Getting to know your appliance . . . . . . . . . . . . 11
Cooking surface. . . . . . . . . . . . .
The control panel . . . . . . . . . . . .
Overview of the menus. . . . . . . .
Cooking position display . . . . . .
Activate the active Light lighting.
Residual heat indicator. . . . . . . .
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
. 11
. 11
. 12
. 13
. 14
. 14
1 Operating the appliance . . . . . . . . . . . . . . . . . . 14
First-time use . . . . . . . . . . . . . . . . . . .
Switching the hob on and off . . . . . . .
Configuring cooking position settings
Chef's recommendations . . . . . . . . . .
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
. 14
. 14
. 14
. 15
O Time-setting options . . . . . . . . . . . . . . . . . . . . . 18
Cooking timer. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Short-term timer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Stopwatch function. . . . . . . . . . . . . . . . . . . . . . . . . . . 19
‚ Wireless temperature sensor . . . . . . . . . . . . . . 23
Preparing and maintaining the wireless temperature
sensor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Connecting the wireless temperature sensor to the
control panel. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Changing the battery . . . . . . . . . . . . . . . . . . . . . . . .
Declaration of Conformity . . . . . . . . . . . . . . . . . . . . .
.23
.23
.24
.24
.25
Ü Cooking sensor . . . . . . . . . . . . . . . . . . . . . . . . . 26
Cooking processes with the cooking sensor
Benefits . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Tips for cooking with the cooking sensor . . .
Setting the boiling point . . . . . . . . . . . . . . . .
Setting procedure . . . . . . . . . . . . . . . . . . . . .
Recommended dishes . . . . . . . . . . . . . . . . .
Meal assistant. . . . . . . . . . . . . . . . . . . . . . . .
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.26
.27
.27
.27
.28
.29
.32
‰ powerMove Pro . . . . . . . . . . . . . . . . . . . . . . . . . 33
Activation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .33
Deactivating . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .33
A Childproof lock. . . . . . . . . . . . . . . . . . . . . . . . . . 34
Activating and deactivating the childproof lock . . . . .34
Childproof lock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .34
ŠPause . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
Activation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .34
Deactivating . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .34
b Automatic safety cut-out . . . . . . . . . . . . . . . . . . 34
Q Basic settings. . . . . . . . . . . . . . . . . . . . . . . . . . . 35
Activation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Deactivating . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
To go to the basic settings: . .
Basic settings menu . . . . . . . .
Exiting the basic settings . . . .
Saving or discarding changes
x panBoost function . . . . . . . . . . . . . . . . . . . . . . . 21
o Home Connect . . . . . . . . . . . . . . . . . . . . . . . . . . 36
v PowerBoost function . . . . . . . . . . . . . . . . . . . . . 20
Recommendations for use . . . . . . . . . . . . . . . . . . . . . 21
Activation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Deactivating . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
z Keep warm function. . . . . . . . . . . . . . . . . . . . . . 22
Activation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Deactivating . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
s Transferring settings . . . . . . . . . . . . . . . . . . . . . 22
Activation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Setting up . . . . . . . . . . . . .
Home Connect settings . .
Software update . . . . . . . .
Remote diagnostics . . . . .
About data protection . . . .
Declaration of Conformity .
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.35
.35
.35
.35
.36
.38
.40
.40
.40
.40
e Hood control. . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
Setting up . . . . . . . . . . . . . . . . . .
Disconnecting from the network .
Control the hood via the hob . . .
Hood control settings . . . . . . . . .
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.41
.42
.42
.43
3
en
h Maximum power consumption . . . . . . . . . . . . . 44
D Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
Hob . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
Hob surround . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
{ Frequently Asked Questions (FAQ) . . . . . . . . . 45
3 Trouble shooting . . . . . . . . . . . . . . . . . . . . . . . . 48
Information, warnings and fault codes . . . . . . . . . . . . 48
Tips . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
Demo mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49
4 Customer service . . . . . . . . . . . . . . . . . . . . . . . . 50
E number and FD number . . . . . . . . . . . . . . . . . . . . . 50
Produktinfo
Additional information on products, accessories,
replacement parts and services can be found at
www.siemens-home.bsh-group.com and in the online
shop www.siemens-home.bsh-group.com/eshops
4
Intended use
8Intended use
Read these instructions carefully. Please keep
the instruction and installation manual, as well
as the appliance certificate, in a safe place for
later use or for subsequent owners.
Check the appliance after removing it from the
packaging. If it has suffered any damage in
transport, do not connect the appliance,
contact the Technical Assistance Service and
provide written notification of the damage
caused, otherwise you will lose your right to
any type of compensation.
Only a licensed professional may connect
appliances without plugs. Damage caused by
incorrect connection is not covered under
warranty.
This appliance must be installed according to
the installation instructions included.
This appliance is intended for private domestic
use and the household environment only. The
appliance must only be used for the
preparation of food and beverages. The
cooking process must be supervised. A short
cooking process must be supervised without
interruption. Only use the appliance in
enclosed spaces.
This appliance is intended for use up to a
maximum height of 4000 metres above sea
level.
Do not use covers. These can cause
accidents, for example due to overheating,
catching fire or materials shattering.
Only use safety devices or child protection
grilles approved by ourselves. Unsuitable
safety devices or child protection grilles may
result in accidents.
This appliance is not intended for operation
with an external clock timer or a remote
control.
This appliance may be used by children over
the age of 8 years old and by persons with
reduced physical, sensory or mental
capabilities or by persons with a lack of
experience or knowledge if they are
supervised or are instructed by a person
responsible for their safety how to use the
appliance safely and have understood the
associated hazards.
I nt ended us e
en
Children must not play with, on, or around the
appliance. Children must not clean the
appliance or carry out general maintenance
unless they are at least 15 years old and are
being supervised.
Keep children below the age of 8 years old at
a safe distance from the appliance and power
cable.
If you are using the cooking sensor, make
sure that the cooking zone you have
configured is the one on which the cookware
with the wireless temperature sensor is
located.
If you wear an active implantable medical
device (e.g. a pacemaker or defibrillator),
check with your doctor that it complies with
Council Directive 90/385/EEC of 20th June
1990, DIN EN 45502-2-1 and DIN EN 455022-2, and that it has been chosen, implanted
and programmed in accordance with VDE-ARE 2750-10. If these conditions are satisfied,
and if, in addition, non-metal cooking utensils
and cookware with non-metal handles are
used, it is safe to use this induction hob as
intended.
5
en
Important safety information
(Important safety
information
I mpor t ant saf et y i nf or mat i on
:Warning – Risk of fire!
Hot oil or grease ignite very easily. Never
leave hot fat or oil unattended. Never use
water to put out burning oil or fat. Switch off
the hob. Extinguish flames carefully using a
lid, fire blanket or something similar.
Risk
of fire!
■
The
cooking surface becomes very hot. Do
not set any combustible objects on the hob.
Do not store any objects on the hob.
Risk
of fire!
■
The
appliance gets hot. Do not keep
combustible objects or aerosol cans in
drawers directly underneath the hob.
Risk
of fire!
■
The
hob switches off automatically and can
no longer be operated. It may switch on
unintentionally at a later point. Switch off the
circuit breaker in the fuse box. Contact the
after-sales service.
Risk
burns!
■
Doofnot
use hob covers here.They can
cause accidents, for example due to
overheating, catching fire or materials
shattering.
■
: Warning – Risk of burns!
The cooking positions and the adjacent
areas, particularly the hob frame (if
present), become extremely hot. Never
touch the hot surfaces. Keep children away
from the appliance.
Risk
of burns!
■
The
hotplate heats up but the display does
not work. Switch off the fuse in the fuse box.
Inform technical after-sales service.
Risk
of burns!
■
Metal
objects on the hob quickly become
very hot. Never set metal objects, such as
knives, forks, spoons, lids, or other objects
that contain metal on the hob.
Risk
of fire!!
■
After
each use, always turn off the hob at
the main switch. Do not wait until the hob
turns off automatically after the pan is
removed.
■
6
: Warning. Risk of electric shock!
Incorrect repairs are dangerous. Repairs
may only be carried out and damaged
power cables replaced by one of our
trained after-sales technicians. If the
appliance is defective, unplug the appliance
from the mains or switch off the circuit
breaker in the fuse box. Contact the aftersales service.
Risk
electric
■
Doofnot
use shock!
any high-pressure cleaners or
steam cleaners, which can result in an
electric shock.
Risk
electric shock!
■
A of
defective
appliance may cause electric
shock. Never switch on a defective
appliance. Unplug the appliance from the
mains or switch off the circuit breaker in the
fuse box. Contact the after-sales service.
Risk
of electric
shock! in the glass ceramic
■
Cracks
or fractures
may cause electric shocks. Switch off the
circuit breaker in the fuse box. Contact the
after-sales service.
■
: Warning. Hazard due to magnetism!
The wireless cooking sensor is magnetic.The
magnetic elements may damage electronic
implants, e.g. pacemakers or insulin pumps.
People fitted with electronic implants should
therefore not carry the cooking sensor in their
pockets and always keep it at least 10 cm
away from their pacemaker or similar medical
device.
: Warning. Risk of fault!
A fan is located on the underside of this hob. If
a drawer is located on the underside of the
hob, do not store any small or sharp objects,
paper or tea towels in it. These may be sucked
in and damage the fan or impair the cooling.
There must be a clearance of at least 2 cm
between the contents of the drawer and the
fan entry point.
Important safety information
en
: Warning. Risk of injury!
The wireless cooking sensor is powered by
a battery, which may become damaged if it
is exposed to high temperatures. Remove
the sensor from the cookware and store it
away from any heat sources.
Risk
of injury!
■
The
cooking sensor may be very hot when
removing it from the saucepan. Wear oven
gloves or use a tea towel to remove it.
Risk
of injury!
■
When
cooking in a bain marie, the hob and
cooking container could shatter due to
overheating. The cooking container in the
bain marie must not directly touch the
bottom of the water-filled pot. Only use heatresistant cookware.
Risk
of injury! may suddenly jump due to
■
Saucepans
liquid between the pan base and the
cooking position. Always keep the cooking
position and saucepan bases dry.
■
7
en
Causes of damage
]Causes of damage
Caution!
Rough pan bases may scratch the hob.
■
Avoid leaving empty pots and pans on the hotplate.
Doing so may cause damage.
■
Do not place hot cookware on the control panel, the
display areas, the hob frame or the light strips at the
sides. This may cause damage.
■
Hard or pointed objects dropped on the hob may
damage it.
■
Aluminium foil and plastic containers will melt if
placed on the hotplate while it is hot. The use of
laminated sheeting is not recommended on the hob.
Causes of damge
■
Overview
You will find the most frequently caused damage in the
following table:
Damage
Stains
Scratches
Discolouration
Chips
8
Cause
Boiled over food.
Unsuitable cleaning agent.
Salt, sugar and sand.
Cookware with rough bases scratch the hob.
Unsuitable cleaning agent.
Pan abrasion.
Sugar, food with a high sugar content.
Measure
Remove boiled over food immediately with a glass scraper.
Only use cleaning agents that are suitable for this type of hob.
Do not use the hob as a work surface or storage space.
Check the cookware.
Only use cleaning agents that are suitable for this type of hob.
Lift pots and pans when moving them.
Remove boiled over food immediately with a glass scraper.
Environmental protection
7Environmental protection
In this section, you can find information about saving
energy and disposing of the appliance.
Envi r onment al pr ot ect i on
Tips for saving energy
■
■
■
■
■
■
Always use a matching lid with your cookware.
Cooking without a lid consumes significantly more
energy. Use a glass lid. This allows you to see into
the pan without removing the lid.
Use cookware with a flat base. Uneven bases
increase the energy consumption.
Always place items of cookware inside the usable
area of the cooking surface.
Use small pots and pans to cook small quantities.
Using cookware that is big but barely filled requires
a lot of energy.
Cook with as little water as possible. This saves
energy and preserves the vitamins and minerals in
vegetables.
Switch to a lower power level in good time. This
prevents energy from being wasted.
fInduction cooking
I nd u c t i o n c o k i n g
Advantages of induction cooking
Induction cooking is fundamentally different from
traditional cooking methods, as heat builds up directly
in the item of cookware. This offers numerous
advantages:
■
■
■
■
Dispose of packaging in an environmentally-friendly
manner.
This appliance is labelled in accordance with
European Directive 2012/19/EU concerning
used electrical and electronic appliances
(waste electrical and electronic equipment WEEE). The guideline determines the
framework for the return and recycling of used
appliances as applicable throughout the EU.
The wireless cooking sensor is battery-powered.
Dispose of spent batteries in an environmentally
responsible manner.
Saves time when boiling and frying.
Energy savings.
Easier to care for and clean. Spilled food does not
burn on as quickly.
Heat control and safety – the hob increases or
decreases the heat supply as soon as the user
changes the setting. If the cookware is removed, the
induction cooking position immediately interrupts the
heat supply without it having been switched off.
Cookware
Only use ferromagnetic cookware for induction cooking,
such as:
■
Environmentally-friendly disposal
en
■
■
Cookware made from enamelled steel
Cookware made from cast iron
Special induction-compatible cookware made from
stainless steel.
To find out whether your cookware is suitable for
induction cooking, check whether a magnet is attracted
to the base of the item or refer to the manufacturer's
specifications.
Some induction cookware does not have a fully
ferromagnetic base:
■
If the base of the cookware is only partially
ferromagnetic, only the area that is ferromagnetic will
heat up. This may mean that heat will not be
distributed evenly. The non-ferromagnetic area may
not heat up to a sufficient temperature for cooking.
9
en
■
Induction cooking
The ferromagnetic area will also be reduced if the
material from which the base of the cookware is
made contains aluminium, for example. This may
mean that the cookware will not become sufficiently
hot or even that it will not be detected.
Pan detection
The hob uses the ferromagnetic diameter and material
of the base of the cookware to automatically detect the
position, size and shape of the cookware being used.
Cookware with a base measuring 90 to 340 mm in
diameter is suitable for use.
‘FP
‘FP
‘FP
Unsuitable pans
Never use diffuser hobs or pans made from:
■
■
■
■
■
common thin steel
glass
earthenware
copper
aluminium
Properties of the base of the cookware
The material(s) from which the base of the cookware is
made can affect the cooking result. Cookware made of
materials that distribute heat evenly, such as saucepans
with a stainless steel sandwich base, save time and
energy.
Cookware with a completely flat base works best. If the
base of the cookware is uneven or embossed, this will
reduce the heat supply.
Cookware that has been removed or is of an
unsuitable size
Always place items of cookware inside the usable area
of the cooking surface. If the cookware is not positioned
correctly, is made of an unsuitable material or is not the
right size, the : symbol will appear next to the cooking
position display. Move the cookware or try again with a
different pot or pan.
If you lift the "active" cookware from the cooking surface
for more than 30 seconds, the cooking position
automatically switches off.
Empty cookware or cookware with a thin base
Do not heat empty items of cookware and do not use
cookware that has a thin base. The hob is equipped
with an internal safety system. However, an empty item
of cookware can heat up so quickly that the automatic
switch-off function has no time to react and an
excessively high temperature is reached. This could
melt the base of the cookware and damage the glass
plate. If this happens, switch off the hob and do not
touch the cookware. If this no longer works once it has
cooled down, contact our technical after-sales service.
10
Note: The cooking position displays may show a size
and shape that is different from the cookware actually
being used. This is normal and does not affect the
functioning of the hob. For more information, see the
section entitled ~ "Frequently Asked Questions
(FAQ)".
Getting to know your appliance
*Getting to know your
appliance
This section explains how to use the cooking surface,
the control panel and the various different functions of
the appliance.
en
Notes
■
Always keep the control panel clean and dry.
Moisture can prevent it from working properly.
■
Never place hot cookware on the touchscreen
display. The electronics could overheat.
Get i ng t o know your ap l i ance
Note: Depending on the appliance model, individual
details and colours may differ.
Cooking surface
The entire cooking surface of the hob supplies
induction heating. Place the item of cookware anywhere
on the usable cooking surface. The position, the size
and the shape of the cookware is detected
automatically.
Note: Up to five items of cookware can be heated on
the cooking surface at the same time.
Selection sensors
Main switch
#
E
H
=
a
Ÿ
Wi-Fi
Pause function
Hood control light
Hood control
Docking menu
l
'
®
Hob
1 Usable cooking surface
2 Control panel
The control panel
The control panel has buttons and a touchscreen
display.
Buttons
The buttons are touch-sensitive. To select a function,
touch the relevant symbol. The available functions will
appear in the display.
þ
V
ª
Info menu
Childproof lock
Basic settings
Stopwatch
Timer
powerMove Pro
Cooking modes menu
Power levels
”
ª
»
/
PowerMove Pro
Cooking sensor
Meal assistant
Cooking zone
1.0–9.0 Power levels
PowerBoost function
ï
Ý
è
x
ShortBoost function
Keep-warm function
Cooking timer
11
Getting to know your appliance
en
Touchscreen display
The touchscreen display gives you an overview of the
cookware on the cooking surface and the buttons for
activating the various functions.
When an item of cookware is set down on the cooking
surface, the cooking position display for this cookware
is shown on the display.
Status bar
You can access certain functions and other menus via
the status bar.
The status bar shows the following options:
■
■
■
■
■
■
■
E Wi-Fi
= Hood control light
a Hood control
% Docking menu
þ Stopwatch
® Basic settings
ÿ powerMove Pro
Docking menu
You can access certain functions and further menus via
the Docking menu.
To open the Docking menu, touch the % symbol at the
bottom of the main screen in the middle and swipe up.
Overview of the menus
The intuitive menu structure helps you to find your way
around the control panel of your hob. You can find out
more about the most important menus in this section.
Main screen
The main display provides an overview of the indicators
for the cookware on the cooking surface. It displays the
cooking mode, power levels, and the timer functions
that are set for the cooking zones that are switched on.
Settings area
Go to the settings area for a particular cooking position
if you want to configure the heat settings, cooking times
or the various cooking modes for this cooking position.
To bring up the settings area, touch the cooking
position indicator you require.
ž
3RZHUOHYHO
12
ERRVW
ERRVW
The Docking menu displays the following options:
■
■
■
Info menu l
Childproof lock '
Basic settings ®
To close the Docking menu, touch the × symbol again
and swipe down.
Info menu
You can access information about the appliance using
the Info menu.
To navigate to the Info menu, open the Docking menu
and touch the l symbol. The available options will be
displayed.
To exit the Info menu, touch the b symbol.
You can also access information about the functions
you are currently using. To do this, touch the symbol for
or the name of the function you require and hold it for a
few seconds. On the display, an info window will appear
that describes the current function.
Getting to know your appliance
Notifications and instructions
Shows information about a change in the appliance's
status or notifies user when they need to do something.
Follow the instructions in the display panel.
Cooking position display
Cooking modes menu
The hob has a number of different cooking modes.
Cooking zone detected
Cooking mode
” Power levels
ª powerMove Pro
» Cooking sensor
/ Meal assistant
Function
This enables you to select the power level
for each item of cookware.
This enables you to control a certain
power level according to the position of
the cookware by moving the cookware
from front to back over the cooking surface.
You can use the cooking sensor that is
attached to the outside of the cookware
to automatically keep the temperature at
a set level. These functions are designed
for foods that need to be cooked with a
lot of water or fried with a lot of oil/fat in
the pan.
Note: This function will be ready to use
once the wireless cooking sensor is connected to the control panel.
Cooking with food pre-selection
To navigate to the Cooking modes menu, select the
cooking position and touch the active cooking mode.
en
When you place an item of cookware on the cooking
surface, the indicator for the relevant cooking position
will light up on the touchscreen display.
The cookware has been detected on the cooking zone. The cooking zone indicator lights up.
Touch the indicator to select the cooking zone.
Selected cooking zone
The displayed cooking zone has been
selected. You can set the power level.
The cooking zone is activated
The displayed cooking zone has been activated. The selected power level lights up in the
display.
ž
3RZHUOHYHO
There is no cookware on the cooking zone
ERRVW
The cookware has been removed from the
cooking zone. The previously selected power
level changes colour.
Other indicators and symbols
The selected cooking zone cannot be programmed.
Touch the : symbol in the status bar for
more information.
Possible causes:
■
You can cook with up to five items of cookware evenly distributed over the cooking
surface at the same time.
■
The cookware is not suitable for use on an
induction hob.
■
The appliance has exceeded its maximum
power consumption.
13
Operating the appliance
en
Activate the active Light lighting.
The cooking surface has interactive light lines on the left
and right of the hob. The light lines show the position of
the cookware on the cooking surface and the status of
the relevant cooking zone.
For instructions on how to activate or deactivate the
light lines, see the section entitled ~ "Basic settings"
The following table shows the meanings of the different
colours:
Colour
White
Blue
Blue colour area
Orange
Red
Meaning
The cookware on the cooking surface has
been detected.
The segment of the cooking surface is
activated.
The powerMove Pro is activated.
You can move the cookware along the
blue light line.
Cooking sensor
Residual heat indicator
Note: If the red light strips on both sides of
the cooking surface flash, an error has occurred.
Residual heat indicator
The hob has two residual heat indicators:
■
■
Touch the f symbol on the main screen. One, two or
all three lines light up depending on the intensity of
the residual heat.
The brightness with which the red light strips light up
indicates the intensity of the residual heat.
They indicate that the cooking surface is still hot. Do not
touch the cooking surface while the indicators are still lit
or immediately after they have gone out.
The residual heat indicators will remain lit for as long as
the cooking surface is still hot, even after you switch the
hob off.
1Operating the appliance
This chapter explains how to set a cooking position.
The table shows heat settings and cooking times for
various meals.
Oper at i ng t he ap l i ance
First-time use
When you switch on the appliance for the first time, the
menu for selecting the initial settings appears on the
display. Select the settings you require.
Once you have confirmed these settings, the main
screen will appear.
Note: You can change the settings at any time.For
information on how to select these settings, see the
section entitled ~ "Basic settings".
Switching the hob on and off
The main switch is used to switch the hob on and off.
To switch the hob on: Touch the # symbol. The
indicator above the main switch lights up. After a short
switch-on time, the hob will be ready for operation.
To switch the hob off: Touch the # symbol. The
display switches off. All the cooking positions are
switched off.
The residual heat indicator will remain lit until the
cooking positions have cooled down sufficiently.
Notes
The hob will automatically switch off if the cooking
positions have been switched off for more than
30 seconds.
■
The settings are stored for 10 seconds after the hob
has been switched off. If you switch the hob back on
during this time, the option to confirm the previous
settings will appear on the main screen. For
information on this setting, see the section entitled
~ "Basic settings".
■
Configuring cooking position settings
The required heat setting is selected in the settings
area.
Heat setting 1.0
Heat setting 9.0
= lowest setting
= highest setting
Each heat setting has an intermediate setting ending in
.5.
Notes
■
To protect the fragile parts of your appliance from
overheating and electrical overloading, the hob may
temporarily reduce the power.
■
In order to prevent the appliance from producing
excess noise, the hob may temporarily reduce the
power.
14
Operating the appliance
Chef's recommendations
Selecting a cooking position and heat setting
The hob must be switched on.
Recommendations
1. Place the cookware on the cooking surface.
2. Touch the symbol for the cooking position you
■
require to select the cooking position. The settings
area for the cooking position you have selected will
appear on the display panel.
■
■
■
■
■
■
■
3. Swipe your finger over the settings area and touch
■
the heat setting you require.
■
ž
en
When heating up puree, cream soups and thick
sauces, stir occasionally.
Set heat setting 8 to 9 for preheating.
When cooking with the lid on, turn the heat setting
down as soon as steam escapes between the lid
and the cookware. Steam does not need to escape
for a good cooking result.
After cooking, keep the lid on the cookware until you
serve the food.
To cook with the pressure cooker, observe the
manufacturer's instructions.
Do not cook food for too long, otherwise the
nutrients will be lost. The kitchen clock can be used
to set the optimum cooking time.
For a more healthy cooking result, smoking oil
should be avoided.
To brown food, fry small portions in succession.
Cookware may reach high temperatures while the
food is cooking. We recommend that you use oven
gloves.
You can find recommendations for energy-efficient
cooking in section ~ "Environmental protection"
ERRVW
3RZHUOHYHO
The heat setting is set.
Changing the heat setting
Select the cooking position and then set the required
heat setting in the control panel.
Switching off a cooking position
Touch the cooking zone indicator on the main display
until the power level ó.ó appears. The cooking zone
switches itself off.
Note: If you place an item of cookware on the cooking
surface before switching on the hob, this will be
detected when you touch the main switch and the
cooking position display will appear on the touchscreen
display.
15
en
Operating the appliance
Recommended dishes
The table shows which heat setting is suitable for each
type of food. The cooking time may vary depending on
the type, weight, thickness and quality of the food.
Ongoing cooking setting
Time (mins)
1.0 - 1.5
1.0 - 2.0
-
Milk 1
1.5 - 2.0
1.5 - 2.5
-
Parboiled sausages 1
3.0 - 4.0
-
Defrosting and heating
Spinach, frozen
Goulash, frozen
3.0 - 4.0
3.0 - 4.0
15 - 25
35 - 55
Potato dumplings 1
4.5 - 5.5
20 - 30
Fish 1
White sauces, e.g. Béchamel sauce
Whisked sauces, e.g. Béarnaise sauce, Hollandaise sauce
4.0 - 5.0
10 - 15
1.0 - 2.0
3.0 - 4.0
3-6
8 - 12
2.5 - 3.5
2.0 - 3.0
15 - 30
30 - 40
4.5 - 5.5
4.5 - 5.5
6.0 - 7.0
25 - 35
15 - 30
6 - 10
3.5 - 4.5
3.5 - 4.5
2.5 - 3.5
3.5 - 4.5
4.5 - 5.5
120 - 180
15 - 60
10 - 20
7 - 20
-
4.0 - 5.0
4.0 - 5.0
3.0 - 4.0
50 - 65
60 - 100
50 - 60
Melting
Chocolate, couverture
Butter, honey, gelatine
Heating or keeping warm
Stew, e.g. lentil stew
Poaching, simmering
Boiling, steaming, braising
Rice (with double the quantity of water)
Rice pudding 3
Unpeeled boiled potatoes
Boiled potatoes
Pasta 1
Stew
Soups
Vegetables
Vegetables, frozen
Stew in a pressure cooker
Braising
Rolled roasting joint
Pot roast
Goulash 3
1 Without a lid
2 Turn frequently.
3 Preheat at level 8.0–8.5.
16
Operating the appliance
Ongoing cooking setting
Time (mins)
6.0 - 7.0
6.0 - 7.0
6.0 - 7.0
6 - 10
6 - 12
6 - 12
Poultry breast (2 cm thick) 2
7.0 - 8.0
5.0 - 6.0
6 - 12
10 - 20
Poultry breast, frozen 2
5.0 - 6.0
10 - 30
Rissoles (3 cm thick) 2
4.5 - 5.5
20 - 30
Hamburgers (2 cm thick) 2
Fish and fish fillet, plain
Fish and fish fillet, breaded
Fish, breaded and frozen, e.g. fish fingers
Prawns and scampi
Sautéing fresh vegetables and mushrooms
Asian-style stir-fries (vegetables and meat cut in strips)
Frozen dishes, e.g. stir-fries
Pancakes (cooked one after the other)
Omelette (cooked one after the other)
Fried eggs
6.0 - 7.0
10 - 20
5.0 - 6.0
6.0 - 7.0
6.0 - 7.0
7.0 - 8.0
7.0 - 8.0
7.0 - 8.0
6.5 - 7.5
6.5 - 7.5
3.5 - 4.5
5.0 - 6.0
8 - 20
8 - 20
8 - 15
4 - 10
10 - 20
15 - 20
6 - 10
3 - 10
3-6
8.0 - 9.0
7.0 - 8.0
6.0 - 7.0
6.0 - 7.0
6.0 - 7.0
5.5 - 6.5
-
Braising/frying with a small amount of oil 1
Escalope, plain or breaded
Escalope, frozen
Chops, plain or breaded 2
Steak (3 cm thick)
Deep-frying 1 (150-200 g per batch in 1-2 l oil, deep-fat fried in batches)
Frozen products, e.g. chips, chicken nuggets
Croquettes, frozen
Meat, e.g. chicken portions
Fish, breaded or battered
Vegetables, mushrooms, breaded, beer-battered or tempura
Small baked items, e.g. doughnuts, beer-battered fruit
en
1 Without a lid
2 Turn frequently.
3 Preheat at level 8.0–8.5.
17
en
Time-setting options
4. To confirm the selected time, touch the
J symbol.
The programmed time appears in the cooking zone
display.
OTime-setting options
Ti me- set i ng opt i ons
Your hob has three timer functions:
■
■
■
Programming the cooking time
Kitchen timer
Stopwatch function
Cooking timer
The cooking position will switch off automatically once
the time that is set has elapsed.
You can set a cooking time of up to 12 hours 59
minutes.
Setting procedure:
The cooking time begins to elapse.
1. Select the cooking position and required power
setting.
2. Touch the x symbol on the cooking zone's settings
area.
ž
Cooking sensor
When you set a cooking time for a cooking zone in
which the cooking sensor is activated, the cooking time
will not start counting down until the selected
temperature level has been reached.
Changing or deleting the time
To navigate to the cooking time, touch the cooking zone
indicator and then select the x symbol.
To change the cooking time, select a new cooking time
and then touch J Start.
ERRVW
To clear the time, touch p.
To return to the main screen, touch b.
3RZHUOHYHO
3. Set the time you require.
To set the number of hours, touch 00 h and select
the time in the settings area.
To set the number of minutes, touch 00 min and
select the time in the settings area.
The seconds appear above the minutes indicator.
You can set intervals of between 30 seconds and 5
minutes.
6ZLWFKRIIWLPHU
K PLQ
5HVHW
18
When the time has elapsed
The cooking position will switch itself off. An audible
signal will sound and the heat setting will be set to 0.0.
Touch the cooking position display to make the time
disappear and stop the audible signal.
Time-setting options
en
Short-term timer
Stopwatch function
You can set a time of up to 9 hours, 59 minutes and 59
seconds on the short-term timer.
You can activate it whether the hob is switched on or
off.
It works independently of the cooking positions and
other settings. This function does not automatically
switch off a cooking position.
The stopwatch function displays the time that has
elapsed since activation.
This functions independently from the cooking position
and from other settings. This function does not
automatically switch off a cooking position.
Setting procedure
The time will begin to elapse.
1. Touch the V sensor.
2. Set the time you require.
Deactivating
To set the number of hours, touch 00 h and select
the time in the settings area.
To set the number of minutes, touch 00 min and
select the time in the settings area.
The seconds appear above the minutes indicator.
You can set intervals of between 30 seconds and 5
minutes.
3. Touch the J symbol.
Activating
Touch the þ symbol in the main area.
To activate the short-term timer, touch the þ sensor.
To clear the time, touch Reset p .
To return to the main screen, touch the ¶ symbol.
The time will now start to elapse.
After a few seconds, the time will appear on the main
screen.
Changing or deleting the time
To activate the short-term timer, touch the V sensor
To change the cooking time, select a new cooking time
and then touch J Start.
To clear the time, touch p.
To return to the main screen, touch b.
When the time has elapsed
An audible signal will sound once the time has elapsed,
and a time of 00:00 will be displayed.
If you touch the V sensor, the time will disappear.
19
en
PowerBoost function
Activation
vPowerBoost function
The PowerBoost function enables you to heat up large
quantities of water faster than when using heat setting
9.
If the Boost option is displayed in the settings area of
the cookware, this function is available.
The powerBoost function is only available for one item
of cookware on each side of the cooking surface.
Power Bo st f unct i on
1. Select a cooking position.
2. Set boost in the settings area. The
Ý symbols will be lit.
ž
ERRVW
ï and
ERRVW
ERRVW
3RZHUOHYHO
3. Select the
If the powerBoost function is activated and you
configure the settings for a different cooking zone on
the same side of the cooking surface, the powerBoost
function will be deactivated and power level 9.0
selected automatically.
If the powerBoost function is activated, you can
configure settings in the middle of the cooking surface
for other items of cookware that are on both sides on
the cooking surface.
ï symbol.
ERRVW
ERRVW
3RZHUOHYHO
This function has now been activated.
ERRVW
Deactivating
Select the cooking position and set a different heat
setting in the settings area.
This function has now been deactivated.
Note: In certain circumstances, the PowerBoost
function can switch itself off automatically in order to
protect the electronic elements inside the hob.
20
panBoost function
Activation
xpanBoost function
The panBoost function enables you to heat cookware
faster than when using heat setting 9.
After deactivating the function, select the appropriate
heat setting for your food.
If the Boost option is displayed in the settings area of
the cookware, this function is available.
The panBoost function is only available for one item of
cookware on each side of the cooking surface.
panBo st f unct i on
1. Select a cooking position.
2. Set boost in the settings area. The
Ý symbols will be lit.
ERRVW
ERRVW
3RZHUOHYHO
3. Select the
Ý symbol.
ERRVW
ž
If the panBoost function is activated and you configure
the settings for a different cooking zone on the same
side of the cooking surface, the panBoost function will
be deactivated and power level 9.0 selected
automatically.
If the panBoost function is activated, you can configure
settings in the middle of the cooking surface for other
items of cookware that are on both sides on the
cooking surface.
ï and
ž
ERRVW
en
ERRVW
3RZHUOHYHO
This function has now been activated.
Deactivating
ERRVW
Touch the cooking position display and select any
power level in the settings area.
This function has now been deactivated.
Note: After 30 seconds, this function automatically
switches itself off.
The cooking position automatically switches back to
power level 9.0.
Recommendations for use
■
■
■
■
■
Always use cold cookware.
Use cookware with a fully flat base. Do not use
cookware with a thin base.
Never leave empty cookware, oil, butter or lard
unattended when it is being heated.
Do not place a lid on the cookware.
For information on the type, size and positioning of
the cookware, see the section entitled ~ "Induction
cooking".
21
en
Keep warm function
zKeep warm function
sTransferring settings
This function is suitable for melting chocolate or butter
and for keeping food warm.
Ke p war m f unct i on
Activation
1. Select a cooking position.
2. Select the first setting in the settings area. The
indicator will be lit.
è
This function lets you transfer the selected power level
or temperature setting and the cooking time from one
cooking position to another.
If you remove an item of cookware from the cooking
surface or move it, the cooking position it was
previously on stops heating. The settings for the
cooking position will be retained for 30 seconds.
When you place the cookware back in this position, the
same settings will be used.
Tr ansf er i ng set i ngs
Activation
1. Place an item of cookware on the cooking surface.
.HHSZDUP
ERRVW
3RZHUOHYHO
This function has now been activated.
Deactivating
1. Select the cooking position.
2. Select a different power level in the settings area.
The è indicator goes out.
This function has now been deactivated.
The cooking zone display shows the new position of the
cookware with power level.
2. Touch Apply confirm transferral of the settings.
7KHFRRNZDUHZDVWUDQVIHUUHGWRDQRWKHU
SRVLWLRQ'R\RXZDQWWRDSSO\WKH
VHWWLQJVWRWKHQHZSRVLWLRQ"
'LVFDUG
$SSO\
The settings have been transferred to the new cooking
position.
22
Wireless temperature sensor
‚Wireless temperature
sensor
en
Fitting the wireless temperature sensor
Attach the temperature sensor to the silicone patch and
align it correctly.
Wir el es t emper at ur e sensor
Connect the wireless cooking sensor to the control
panel before using the cooking sensor functions for the
first time.
Preparing and maintaining the wireless
temperature sensor
This section provides information on:
■
■
■
■
Attaching the silicone patch
Attaching the wireless cooking sensor
Cleaning
Replacing the battery
The silicone patch and temperature sensor can be
purchased from specialist retailers or through our
technical after-sales service or our official website. To
do this, quote the relevant reference number:
00577921
HZ39050
Set of 5 silicone patches
Temperature sensor and set of 5 silicone patches
Adhering the silicone patch
The silicone patch attaches the wireless cooking sensor
to the cookware.
If you are using an item of cookware with cooking
sensor functions for the first time, attach the silicone
patch directly to it. Proceed as follows:
1. That the adhesive area on the pan is free from
grease. Clean the pan, dry it thoroughly and wipe the
adhesive area with a spirit.
2. Remove the protective film from the silicone patch.
Adhere the silicone patch to the outside of the pan in
the correct place using the enclosed template as a
guide.
Notes
■
Ensure that the silicone patch is completely dry
before attaching the cooking sensor.
■
Fill the pot so that the contents reach high enough to
cover the cooking sensor's silicone patch.
■
To prevent overheating, do not attach the cooking
sensor to other hot cookware.
■
Remove the cooking sensor from the pot after
cooking. Store it in a clean, safe place away from
sources of heat.
■
You can use up to three cooking sensors at the
same time.
Connecting the wireless temperature sensor
to the control panel
To connect the wireless temperature sensor to the
control panel, follow the instructions below:
1. Open the docking menu.
2. Open the basic settings and select "Cooking sensor"
from the menu.
3. Select the Add a new cooking sensor option.
Press the » symbol on the wireless temperature
sensor within 30 seconds.
After a few seconds, the status of the connection
between the temperature sensor and the control
panel will appear on the display.
The cooking sensor functions are made available once
the wireless cooking sensor has been connected to the
control panel correctly.
3. Press down all over the surface of the silicone patch,
including in the centre.
The adhesive requires one hour to fully harden. Do not
use or clean the pan during this time.
Notes
■
Do not leave the pan with the silicone patch to soak
soapy water for long periods of time.
■
If the silicone patch comes off, attach a new one.
Notes
■
A faulty connection due to the wireless cooking
sensor not being detected may be caused by the
following:
– Bluetooth communication error.
– You did not press the symbol on the wireless
cooking sensor within 30 seconds.
– The battery in the wireless cooking sensor is
almost flat.
Reset the wireless cooking sensor and repeat the
connection procedure.
■
If there are problems with the connection due to a
transmission error, repeat the connection procedure.
If you continue to experience connection problems,
contact our technical after-sales services.
23
en
Wireless temperature sensor
Resetting the wireless temperature sensor
1. Touch the
» symbol on the cooking sensor for
approximately 8-10 seconds.
While you are doing this, the temperature sensor's
LED indicator will light up three times. When the LED
lights up for the third time, it will start to reset the
temperature sensor. Stop touching the symbol when
this happens.
Once the LED goes out, this means that the wireless
temperature sensor has been reset.
2. Repeat the connection procedure.
Changing the battery
Changi ng t he bat er y
If the temperature sensor does not light up when the
symbol is pressed, the battery is flat.
Changing the battery:
1. Remove the silicone cover from the lower section of
the temperature sensor housing and remove both
screws using a screwdriver.
Cleaning
Do not clean the wireless temperature sensor in the
dishwasher.
Temperature sensor
Clean the temperature sensor with a damp cloth. Never
clean it in the dishwasher. Do not immerse it in water or
clean it under running water.
Remove the temperature sensor from the saucepan
after cooking. Store it in a clean, safe place (such as in
its packaging) away from sources of heat.
2. Open the closure of the temperature sensor.
Remove the battery from the lower section of the
housing and insert a new battery (pay attention to
the correct orientation of the battery poles).
Silicone patch
Clean and dry before attaching to the temperature
sensor. Dishwasher safe.
Note:
Cookware with the silicone patch must not be left to
soak for long periods in soapy water.
Temperature sensor window
The sensor window must always be clean and dry.
Proceed as follows:
■
■
Remove dirt and oil splatters regularly.
Use a soft cloth or cotton buds and window cleaner
for cleaning.
Caution!
Do not use any metal objects to remove the battery.
Do not touch the battery connection points.
Notes
Do not use abrasive cleaning agents such as
scouring pads, scrubbing brushes or cream
cleaners.
■
Do not touch the sensor window with your fingers.
This may make it dirty or scratch it.
■
24
Wireless temperature sensor
en
3. Close the closure of the temperature sensor (the
notches for the screws on the closure must align
with the notches on the lower section of the
housing). Tighten the screws with a screwdriver.
4. Reattach the silicone cover to the lower section of
the temperature sensor housing.
Note:
Use only high-quality batteries of the type CR2032 in
order to guarantee a long service life.
Declaration of Conformity
BSH Hausgeräte GmbH hereby declares that the
appliance with wireless temperature sensor function
meets the basic requirements and other relevant
provisions of the Directive 2014/53/EU.
A detailed RED Declaration of Conformity can be found
online at www.siemens-home.bsh-group.com on the
product page of your appliance with the additional
documents.
The logos and the Bluetooth® brand are registered
trademarks and property of Bluetooth SIG, Inc. These
trademarks are used by BSH Hausgeräte GmbH under
licence. All other trademarks and brand names are
owned by the respective companies.
25
en
Cooking sensor
ÜCooking sensor
The cooking sensor is guaranteed to make cooking
simple and it promises outstanding cooking results.
The wireless cooking sensor continuously measures the
temperature of the cookware. This allows cooking to be
precisely regulated and the temperature to be
maintained at the required level at all times in order to
prevent excessively vigorous boiling and to achieve
perfect cooking results.
Add your food once the selected temperature has been
reached. The temperature is automatically kept
constant without you having to change the temperature
level.
Co ki ng sensor
Provided there is a wireless cooking sensor, the
cooking sensor is available over the entire cooking
surface.
The wireless cooking sensor forwards the temperature
of the cookware to the control panel.
The hob has a wireless cooking sensor. If necessary,
you can purchase this retroactively from specialist
retailers, via our technical after-sales service or in our
online shop. You can use up to three cooking sensors
at the same time.
Note: The cooking sensor can be ordered by quoting
the reference number HZ39050.
For more information on the cooking sensor, see the
section entitled ~ "Wireless temperature sensor".
Cooking processes with the cooking sensor
You can use the cooking sensor to select the best
cooking type for each kind of food.
The table shows the available cooking processes:
Cooking processes
Temperature
Cookware
Suitable for
Keeping warm, heating
70 ºC
E.g. punch, goulash
Poaching in milk
85 ºC
E.g. panna cotta, rice pudding
Poaching in water
90 °C
E.g. rice, quinoa
Boiling
100 °C
E.g. pasta, gnocchi, vegetables
Cooking in a pressure cooker
115 ºC
E.g. home-made broths, pulses
Deep-frying at a low temperature*
160 °C
E.g. doughnuts, fritters
Deep-frying at a medium temperature*
170 ºC
E.g. breaded fish, meatballs
Deep-frying at a high temperature*
180 ºC
E.g. chips, frozen
*Preheat with the lid on and deep-fry with the lid off.
26
Cooking sensor
Benefits
■
■
■
The cooking zone only emits heat when this is
necessary to maintain the temperature. This saves
energy.
The temperature is continuously monitored. This
means that the food will not spill over and you do not
need to change the temperature level.
The cooking sensor detects when the water or the oil
has reached the optimum temperature for adding
the food (foods that should be added at the start of
cooking are indicated in the table).
Notes
■
Use cookware with a thick, flat base. Do not use
cookware with a thin or deformed base.
■
Fill the item of cookware so that the contents reach
high enough to cover the cooking sensor's silicone
patch.
■
Do not remove the wireless cooking sensor from the
cookware during cooking.
■
After cooking, remove the wireless sensor from the
cookware. Take care when doing so because the
wireless cooking sensor may be very hot.
Tips for cooking with the cooking sensor
■
■
■
■
■
Keeping warm/heating: Portions of frozen products,
e.g. spinach. Place the frozen product in the
cookware. Add the volume of water specified by the
manufacturer.Cover the cookware with a lid. Select
the temperature recommended in the table.
Poaching: This cooking method is suitable for
cooking food at low temperatures, thickening
sauces, reducing stews and cooking with milk.
Select the temperature recommended in the table for
the food you want to cook.
Boiling: This cooking method allows you to boil
water with a lid on without it boiling over. This
temperature control allows water to be boiled more
efficiently. Select the temperature recommended in
the table.
Cooking in a pressure cooker: Follow the
manufacturer's recommendations. After the signal
tone sounds, continue cooking for the
recommended time. Select the temperature
recommended in the table.
Deep-fat frying: It is recommended that you heat oil
with a lid on.Once the signal tone has sounded,
remove the lid and add the food. Select the
temperature recommended in the table for the food
you want to cook.
en
Notes
■
Always cook with a lid, except when using the deepfrying function.
■
If no signal sounds, make sure that there is a lid on
the cookware. If there is a lid on the pan and still the
signal doesn´t sound, the appliance may have
reached its maximum power consumption or the
Maximum power consumption setting may have
been activated. This may affect the time required to
reach the selected temperature. Switch off or reduce
the power levels for the other pots and pans. See the
section entitled ~ "Basic settings"
■
Never leave oil unattended when it is being heated.
Use oil that is suitable for deep-frying. Do not mix
different cooking fats and oils – e.g. oil and lard – as
such mixtures may foam up when hot.
■
If you are not satisfied with the cooking result, e.g.
when cooking potatoes, next time use less water but
keep the recommended temperature level.
Setting the boiling point
The point at which water starts to boil depends on the
height of your home above sea level. If the water is
boiling too vigorously or not vigorously enough, you can
set the boiling point. Proceed as follows:
■
■
Open the Docking menu and the touch the ®
symbol. Go to the basic setting Set the boiling point.
The default basic setting is 200–400 m. If your
home is located at a height of between 200 and 400
metres above sea level, do not set the boiling point.
Select the setting that matches your home's height
above sea level.
Note: The temperature level 100 ºC is sufficient for
efficient boiling, even if the water does not boil very
strongly. You can always change the boiling point if you
wish – if you want the water to boil more strongly, for
example, you can select a lower altitude.
27
en
Cooking sensor
Setting procedure
1. Attach the cooking sensor to the saucepan; see the
section entitled
2. Fill the cookware with a sufficient amount of liquid,
3.
4.
5.
6.
7.
put the lid on and place it on the cooking surface.
See the section entitled ~ "Fitting the wireless
temperature sensor".
Touch the cooking position display for the cookware.
Touch the active cooking mode and select the
»Cooking sensor option.
Note: The cooking sensor is only available if the
wireless cooking sensor is connected to the control
panel. See the section entitled ~ "Wireless
temperature sensor"
Touch the » symbol for the wireless temperature
sensor.
Select the temperature level.
The function has now been activated.
The cooking position indicator and the selected
temperature flash until the selected temperature has
been reached. A signal then sounds.
When the signal tone sounds, remove the lid and
add the food. Leave the lid on while cooking.
Tip: If you want to set the temperature more precisely,
you can increase or decrease this by 1 °C to 5 °C. To
do this, touch the selected temperature and then touch
the © symbol.
Then select the required temperature.
To cancel and exit the menu, touch the ¶ symbol.
28
Cooking sensor
en
Recommended dishes
The following table shows a selection of dishes and is
arranged by food type. The temperature and the
cooking time depend on the amount, the condition and
the quality of the food.
Meat
Temperature
Time (mins)
90 °C
10 - 20
Meatballs 1
100 °C
20 - 30
Chicken 1
100 °C
60 - 90
Veal 1
100 °C
60 - 90
115 °C
115 °C
15 - 25
15 - 25
Deep-frying chicken portions 3
170 °C
10 - 15
Deep-frying meatballs 3
170 °C
10 - 15
Temperature
Time (mins)
90 °C
15 - 20
Deep-frying battered fish 2
170 °C
10 - 15
Deep-frying breaded fish 2
170 °C
10 - 15
Temperature
Time (mins)
100 °C
5 - 10
Poaching
Sausages 1
Boiling
Cooking in a pressure cooker
Chicken in a pressure cooker 2
Veal in a pressure cooker
2
Deep-frying
1
Pre-heat and cook with the lid on. Add the food when the audible signal sounds.
2 Add the food at the start.
3 Heat the oil with the lid on. Fry one portion after the other without the lid.
Fish
Poaching
Braised fish 1
Deep-frying
1
Pre-heat and cook with the lid on. Add the food when the audible signal sounds.
2 Heat the oil with the lid on. Fry one portion after the other without the lid.
Egg dishes
Boiling
Boiled eggs 1
1 Add the food at the start
29
Cooking sensor
en
Vegetables and pulses
Temperature
Time (mins)
Broccoli 1
100 °C
10 - 20
Cauliflower 1
100 °C
10 - 20
Spinach 1
100 °C
5 - 10
Brussels sprouts 1
100 °C
30 - 40
Green beans 1
100 °C
15 - 30
Chickpeas 2
100 °C
60 - 90
Peas 1
100 °C
15 - 20
Lentils 2
100 °C
45 - 60
115 °C
3-6
Haricot beans in a pressure cooker 2
115 °C
115 °C
25 - 35
25 - 35
Lentils in a pressure cooker 2
115 °C
10 - 20
Deep-frying breaded vegetables 3
170 °C
4-8
Deep-frying battered vegetables 3
170 °C
4-8
Deep-frying breaded mushrooms 3
170 °C
4-8
Deep-frying battered mushrooms 3
170 °C
4-8
Temperature
Time (mins)
85 °C
30 - 40
Gnocchi 1
100 °C
3-6
Boiling potatoes 2
Boiling sweet potatoes 2
100 °C
30 - 45
100 °C
30 - 45
115 °C
10 - 20
115 °C
10 - 20
160 °C
8 - 12
Boiling
Cooking in a pressure cooker
Vegetables in a pressure cooker 2
Chickpeas in a pressure cooker 2
Deep-frying
1
Pre-heat and cook with the lid on. Add the food when the audible signal sounds.
2 Add the food at the start.
3 Heat the oil with the lid on. Fry one portion after the other without the lid.
Potatoes
Poaching
Cooking potato dumplings 1
Boiling
Cooking in a pressure cooker
Potatoes in a pressure cooker 2
Sweet potatoes in a pressure cooker 2
Deep-frying
Potatoes with a spicy sauce 3
1
Pre-heat and cook with the lid on. Add the food when the audible signal sounds.
2 Add the food at the start.
3 Heat the oil with the lid on. Fry one portion after the other without the lid.
30
Cooking sensor
Pasta and cereals
Temperature
Time (mins)
Semolina pudding 3
85 °C
5 - 10
Parboiled rice 1
90 °C
25 - 35
Brown rice 2
90 °C
45 - 55
Exotic rice (e.g. basmati, Thai) 2
90 °C
8 - 12
Wild rice 2
90 °C
20 - 30
Quinoa 1
90 °C
10 - 12
Polenta 3
85 °C
3-8
Durum wheat pasta 3
100 °C
7 - 10
Fresh pasta 3
100 °C
3-5
Wholemeal pasta 3
100 °C
7 - 10
Durum wheat pasta, filled 3
100 °C
15 - 20
Fresh pasta, filled 3
100 °C
5-8
Rice in a pressure cooker 2
115 °C
6-8
Brown rice in a pressure cooker 2
115 °C
12 - 18
Temperature
Time (mins)
90 °C
10 - 15
Home-made broths 1
100 °C
60 - 90
Instant soups 2
100 °C
5 - 10
115 °C
20 - 30
Temperature
Time (mins)
Rice pudding 3
85 °C
40 - 50
Porridge 3
85 °C
10 - 15
Chocolate pudding 3
85 °C
3-5
en
Poaching
Boiling
Cooking in a pressure cooker
1
Pre-heat and cook with the lid on. Add the food when the audible signal sounds.
2 Add the food at the start.
3 Stir frequently.
Soups
Poaching
Instant creamy soups 2
Boiling
Cooking in a pressure cooker
Home-made broths in a pressure cooker 1
1 Add the food at the start.
2 Stir frequently.
Desserts
Poaching
1 Add the food at the start.
2 Heat the oil with the lid on. Fry one portion after the other without the lid.
3 Stir frequently.
31
Cooking sensor
en
Desserts
Temperature
Time (mins)
100 °C
15 - 25
Deep-frying jam-filled doughnuts 2
160 °C
5 - 10
Deep-frying ring doughnuts 2
160 °C
5 - 10
Deep-frying cream puffs 2
160 °C
5 - 10
Boiling
Compote 1
Deep-frying
1 Add the food at the start.
2 Heat the oil with the lid on. Fry one portion after the other without the lid.
3 Stir frequently.
Frozen products
Temperature
Time (mins)
Vegetables in a creamy sauce 4
70 °C
15 - 20
Defrosting broths 2
70 °C
15 - 25
100 °C
15 - 30
180 °C
4-8
Keeping warm, heating
Boiling
Green beans, frozen 1
Deep-frying
Deep-frying chips 3
1
Pre-heat and cook with the lid on. Add the food when the audible signal sounds.
2 Add the food at the start.
3 Heat the oil with the lid on. Fry one portion after the other without the lid.
4 Stir frequently.
Other
Temperature
Time (mins)
Heating goulash soup 1
70 °C
10 - 20
Heating mulled wine 1
70 °C
5 - 15
85 °C
3 - 10
Keeping warm, heating
Poaching
Heating milk 1
1 Add the food at the start.
Meal assistant
This function can be used to cook a wide variety of
food.The appliance will choose the optimal setting for
you.
Activation
1. Select a cooking position.
2. Touch the active cooking mode and select the Meal
assistant option.
3. Select the required food category.
4. Select the required meal.
You will be guided through the entire setting process for
the selected meal and given instructions on how to
prepare this meal.
32
Deactivating
Set the temperature to 0 or select a different cooking
mode.
powerMove Pro
en
3. Move the cookware over the cooking surface until
‰powerMove Pro
This function allows you to change the power level
during cooking simply by moving the cookware
forwards or backwards.
Activating this function will display the preset power
levels for the item of cookware. You can select one of
five available power levels depending on the position of
the cookware.
the power level you require is set. The power level
you have selected will appear on the cooking
position display.
power Move Pr o
Default power levels: è, ð.ó, î.ó, ì.ó and ê.ó.
For information on how to change the preset power
levels, see the section entitled ~ "Basic settings".
Note: If the function does not activate when you select
the power level, the appliance may have reached its
maximum power consumption. For information on how
to set the Maximum power consumption function, see
the section entitled ~ "Basic settings".
Activation
Place the cookware on the cooking surface.
1. Touch the
ª symbol in the main view.
Notes
■
If the function is not available for the cookware you
want to use, an audible signal will sound and the
function will not be activated.
■
If the function is not available for any of the
cookware you have set down, the ª symbol will not
appear on the main display.
Changing the heat setting
You can change the power levels while you are
cooking. To choose a different power level in the
programming area, touch the area you want to change
the power level of.
Note: If the function is deactivated, the power levels will
return to the default values
Deactivating
Touch the cooking zone indicator on the main display
until the power level ó.ó appears. The cooking zone
switches itself off.
This function has now been deactivated.
2. Touch the required cooking zone indicator.
6HOHFWWKHSDQ\RXZDQWWRDFWLYDWH
SRZHU0RYHIRU
'LVFDUG
The function has now been activated.
33
en
Childproof lock
AChildproof lock
You can use the childproof lock to prevent children
from switching on the hob.
Chi l dpr o f l ock
Activating and deactivating the childproof
lock
All cooking zones must be switched off.
Activation
1. Open the docking menu.
2. Touch the ' symbol.
The childproof lock is now activated. The hob is now
locked.
Deactivating
Follow the instructions on the display panel.
The lock is now released.
Childproof lock
With this function, the childproof lock automatically
activates when a hob is switched off.
Switching on and off
You can find out how to switch the automatic childproof
lock on in the ~ "Basic settings" section
ŠPause
The selected settings are retained while the pause
function is activated, but no power level is used and the
cooking times that have been set will stop.
If you have activated the alarm or the timer, it will
continue running. You cannot change the alarm time
when the pause function is activated.
The pause function has no effect on the main switch.
You can still switch off the hob at any time.
Pause
Activation
Touch the H symbol. The hob will remain locked for 30
minutes. You can now clean the surface of the
touchscreen display, for example, without inadvertently
changing the settings.
Deactivating
To deactivate the function before 30 minutes have
passed, touch the H symbol and then touch Continue.
The hob will switch off automatically after 30 minutes.
Note: If you move the cookware across the cooking
surface while the function is still activated, the settings
may be lost.
bAutomatic safety cut-out
If a cooking zone operates for an extended period and
no settings are changed, the automatic safety switch-off
is activated.
This stops the cooking zone from heating up. A
notification will appear on the display.
Touching any symbol will switch off the display. The
cooking zone can now be reset.
The point at which the automatic safety switch-off
becomes active depends on the power setting in use
(after 1 to 10 hours).
Aut omat i c saf et y cut - out
34
Basic settings
en
QBasic settings
The appliance has various basic settings. You can
adapt these settings to your personal requirements.
Basi c set i ngs
Settings
Language
Home Connect
Hood control cookConnect
Signal tones
Signal duration
Signal volume
Button tone
Touch field tone volume
Display brightness
activeLight
Childproof lock
reStart
Max. power consumption
Cooking sensor
Set the boiling point
powerMove Pro power levels
Appliance info.
Factory settings
--------
Description and options
You can change the language of the appliance.
Using this function, you can connect your appliance to your home network and a mobile end device.
You can use this to control important functions of your cooker hood via your hob, e.g. the fan speed and
light.
You can select which signal tones the appliance should sound.
You can change the duration of the signal tones.
Set the volume of the audible signals.
You can choose whether or not the appliance will sound when fields and symbols are touched on the
touchscreen.
Set the volume for when you touch a sensor.
You can change the brightness of the display.
Activate or deactivate activeLight.
You can use the child safety lock to lock the hob and prevent children from using it without supervision.
You can set how long your appliance saves the most recently used settings after it has been switched off.
You can restrict the hob's total power and adapt it to the local mains connection.
You can add a new temperature sensor.
You can enter your height above sea level to improve the cooking sensor's accuracy.
The preset settings for the powerMove Pro function can be changed.
You can view information about your appliance.
You can reset all the settings to the factory settings.
To go to the basic settings:
Open the docking menu and touch the ® symbol. All
cooking position must be switched off.
Basic settings menu
Slide your finger up or down to scroll through the
available settings. Touch a setting to access further
options in its sub-menu.
Within a sub-menu, touch the "¶" symbol to return to
the previous menu.
Exiting the basic settings
Touch the ¶ symbol to leave the "Basic settings"
menu.
Saving or discarding changes
If changes have been made, when you exit the basic
settings you will see a confirmation screen asking you if
you wish to save or reject any changes made.
35
en
Home Connect
oHome Connect
Home Con ect
This appliance is WLAN-enabled and settings can be
sent to the appliance via a mobile device.
If the appliance is not connected to the home network,
the appliance functions in the same way as a hob with
no network connection. The hob can always be
operated via the control panel.
The availability of the Home Connect function depends
on the availability of Home Connect services in your
country. Home Connect services are not available in
every country.You can find more information on this at
www.home-connect.com.
Notes
■
Hobs are not designed to be used unattended - you
must always keep an eye on the cooking process.
■
Ensure that you follow the safety instructions in this
instruction manual and that these are also observed
when operating the appliance via the Home Connect
app. You must also follow the instructions in the
Home Connect app.~ "Important safety
information" on page 6
■
Using the Home Connect app, you can send settings
to your appliance and then have to confirm them on
the appliance. It is not possible to operate the
appliance whilst you are away from home.
■
Operation on the appliance always has priority.
During this time, it is not possible to operate the
appliance using the Home Connect app.
Setting up
To implement settings via Home Connect, you must
have installed and set up the Home Connect app on
your mobile device.
Observe the Home Connect documents supplied for
this.
Follow the steps specified by the app to make the
settings.
The app must be open in order to perform the setup
process.
Automatic registration in the home network
You require a router that has WPS functionality.
You require access to your router.If you do not have
this, follow the steps for "Manually logging into your
home network".
1. Touch the
® symbol in the docking menu to open
the basic settings.
2. Touch the "Home Connect" setting.
3. Touch "Use wizard to configure settings" to launch
the Home Connect assistant.
+RPH&RQQHFW
8VHZL]DUGWRFRQILJXUHVHWWLQJV
A message will appear regarding the mobile device.
4. Touch "Next" to continue.
5. Press the WPS button on the router within the next
2 minutes.
A message will be displayed to notify you when the
hob is successfully connected to your home
network.
Note:
If it is unable to connect, relaunch the assistant or
manually log the appliance into your home network.
A message will appear to say that the appliance can
now be connected to the app.
6. Touch "Next" to begin the process of connecting to
the app.
&RQQHFWWRQHWZRUN
&RQQHFWLRQWRQHWZRUNVXFFHVVIXO
&RQWLQXHWRFRQQHFWWRWKHDSS
1H[W
A message is displayed to notify you that the
connection has been successful. The D symbol will
appear on the main screen. The brightness with which
the D symbol lights up indicates the strength of the
connection.
36
Home Connect
Manual registration in the home network
1. Touch the
® symbol in the docking menu to open
the basic settings.
2. Touch the "Home Connect" setting.
3. Touch "Use wizard to configure settings" to launch
the Home Connect assistant.
You will be asked to press the WPS button on your
router.
en
8. Touch "Next" to begin the process of connecting to
the app.
&RQQHFWWRQHWZRUN
&RQQHFWLRQWRQHWZRUNVXFFHVVIXO
&RQWLQXHWRFRQQHFWWRWKHDSS
4. Select "WPS not supported".
$XWRPDWLFQHWZRUNORJLQ
$FWLYDWHWKH:36IXQFWLRQRQ\RXUURXWHU
PLQV
1H[W
A message is displayed to notify you that the
connection has been successful. The D symbol will
appear on the main screen. The brightness with which
the D symbol lights up indicates the strength of the
connection.
:36QRWVXSSRUWHG
5. Read the message and touch Next to continue.
6. Open the network settings on your mobile device
and use the SSID "Home Connect" and the key
"Home Connect" to log your mobile device into the
hob network.
Note:
If it is unable to connect, relaunch the assistant and
manually log the appliance into your home network.
7. Follow the prompt in the app and enter the name
and password for your home network (Wi-Fi).
A message will appear to say that the appliance can
now be connected to the app.
37
en
Home Connect
Home Connect settings
You can adjust Home Connect to suit your
requirements at any time.
In the basic settings for your hob, navigate to the Home
Connect settings to display network and appliance
information.
Settings
Use wizard to configure settings
Connect to app
Setting via app
Wi-Fi
Disconnect from the network
Appliance info.
Description and options
The hob can be logged into your home network automatically or manually.
■
Use the assistant to configure the settings (automatic connection to the home network)*.
■
Use the assistant to configure the settings: WPS not supported (manually log into your home network).
Note: This setting is only displayed if the hob is not connected to your home network.
You can connect to one or more Home Connect accounts.
Note: This setting is only displayed if the hob is connected to your home network.
You can choose whether to allow cooking settings to be sent.
■
No: Only the hob's current status is displayed in the app.
■
Yes*: The cooking settings can be sent from the app to the hob. The cooking settings that are sent
must be confirmed on the hob.
Note: This setting is only displayed if the hob is connected to your home network.
You can switch off the hob's wireless module to disconnect it from the Wi-Fi.
■
Deactivated: Wireless module switched off.
■
Activated*: Wireless module connected.
Note: This setting is only displayed if the hob is connected to your home network.
You can delete the saved connections to the home network at any time.
Note: This setting is only displayed if the hob is connected to your home network.
This displays information about Home Connect and the network.
Note: This setting is only displayed if the hob is connected to your home network.
*Factory setting
--------
Note:
Use wizard to configure settings is only displayed if the
appliance is not yet connected to your home network.
All other settings are only displayed if the appliance is
already connected to your home network.
Wi-Fi symbols
The Wi-Fi indicator on the main screen changes
according to the status/quality of the connection and
the availability of the Home Connect server.
4. Select Off.
:L)L
2Q
2II
Deactivating Wi-Fi
If Wi-Fi has been activated, you can use the Home
Connect functions.
Note:
In networked standby mode, your appliance requires a
maximum of 2 W.
1. Touch the
® symbol in the docking menu to open
the basic settings.
2. Touch the "Home Connect" setting.
3. Touch "Wi-Fi".
38
This deactivates Wi-Fi; the D symbol will go out on the
control panel.
Home Connect
Disconnecting from the network
1. Touch the
Di scon ect i ng f r om t he net wor k
You can disconnect your hob from the network at any
time.
Note:
If your hob is disconnected from the network, it is not
possible to operate it using Home Connect.
1. Touch the
en
® symbol in the docking menu to open
the basic settings.
2. Touch the "Home Connect" setting.
3. Touch Disconnect from the network.
4. Touch "Next" to confirm.
'LVFRQQHFWIURPWKHQHWZRUN
'HOHWHDOOQHWZRUNVHWWLQJVIURPWKH
DSSOLDQFH"
® symbol in the docking menu to open
the basic settings.
2. Touch the "Home Connect" setting.
3. Select Connect to app.
+RPH&RQQHFW
&RQQHFWWRDSS
:L)L
6HWWLQJYLDDSS
'LVFRQQHFWIURPWKHQHWZRUN
$SSOLDQFHLQIR
You can also connect a second Home Connect account
to the hob. To do this, select Connect to app again.
4. Follow the instructions in the app to complete the
connection process.
1H[W
'LVFDUG
This disconnects the appliance from your home
network; the D symbol will go out on the control panel.
Note:
The network connection will also be deleted if you
restore the factory settings on your appliance.
Connecting to the network
Con ect i ng t o t he net wor k
1. Touch the
® symbol in the docking menu to open
the basic settings.
2. Touch the "Home Connect" setting.
3. Touch "Use wizard to configure settings" to launch
the Home Connect assistant.
4. Follow the instructions as per ~ "Automatic
registration in the home network" or ~ "Manual
registration in the home network".
Connect to the app
If the Home Connect app is installed on your mobile
device, you can connect it to your hob.
Notes
■
The appliance must be connected to the network.
■
The app must be open and be set up.
■
If your extractor hood is directly connected, first
disconnect the hob from your home network and
then initiate the connection process
again.~ "Disconnecting from the network"
on page 39~ "Connecting to the network"
on page 39
Settings via app
The Home Connect app provides easy access to the
basic settings and enables you to send the settings for
the cooking zones to the hob.
Notes
■
The hob must be switched on, but all cooking zones
must be switched off.
■
Operating the appliance directly from the appliance
always takes priority. If you operate the appliance
directly, you can operate it via the Home Connect
app.
■
The appliance is delivered with settings transfer
option activated.
■
If the settings transfer option is deactivated, only the
hob's operating status will be displayed in the Home
Connect app.
1. Touch the
® symbol in the docking menu to open
the basic settings.
2. Touch the "Home Connect" setting.
3. Select Setting via app.
+RPH&RQQHFW
&RQQHFWWRDSS
:L)L
6HWWLQJYLDDSS
'LVFRQQHFWIURPWKHQHWZRUN
$SSOLDQFHLQIR
4. To activate the settings transmission option, touch
On; to deactivate the settings transmission option,
touch Off.
39
en
Home Connect
Confirming settings
Once cooking settings have been successfully
transmitted to a cooking position, a message will
appear on the hob. You will be asked whether you want
to use these settings. To confirm that you want to use
these settings, touch "Apply". To reject these settings,
touch "Discard".
Software update
Using the software update function, the hob's software
can be updated (e.g. for the purpose of optimisation,
troubleshooting or security updates). To use the app,
you must first register as a Home Connect user, install
the app on your mobile device and connect to the
Home Connect server.
The Home Connect app will tell you when a software
update is available. You can start the software update
via the app or the hob. To do this, refer to the
instructions on the display.
Once the update has been successfully downloaded,
you can install it via the Home Connect app if you are
connected to your local area network.
The Home Connect app will notify you when the update
has been successfully installed.
Notes
■
You can continue to use the hob as normal while
updates are downloading.
■
Depending on your personal settings in the app,
software updates can also be set to download
automatically.
■
We recommend that you install security updates as
soon as possible.
About data protection
When your appliance is connected for the first time to a
WLAN network, which is connected to the Internet, your
appliance transmits the following categories of data to
the Home Connect server (initial registration):
■
■
■
■
Unique appliance identification (consisting of
appliance codes as well as the MAC address of the
installed WiFi communication module).
Security certificate of the WiFi communication
module (to ensure a secure IT connection).
The current software and hardware version of your
domestic appliance.
Status of any previous resetting to factory settings.
This initial registration prepares the Home Connect
functions for use and is only required when you want to
use these Home Connect functions for the first time.
Note:
Ensure that the Home Connect functions can be used
only in conjunction with the Home Connect app.
Information on data protection can be accessed in the
Home Connect app.
Declaration of Conformity
BSH Hausgeräte GmbH hereby declares that the
appliance which features Home Connect is in
accordance with the basic requirements and the other
relevant provisions of the directive 2014/53/EU.
A detailed RED Declaration of Conformity can be found
online at www.siemens-home.bsh-group.com on the
product page of your appliance with the additional
documents.
Remote diagnostics
If a fault occurs, the after-sales service can use remote
diagnostics to access your appliance.
Contact the after-sales service, making sure that your
appliance is connected to the Home Connect server
and checking that the remote diagnostics service is
available in your country.
Note:
For more information and to check whether the remote
diagnostics service is available in your country, please
visit the Help & Support area of the Home Connect
website for your country: www.home-connect.com
40
2.4 GHz band: max. 100 mW
5 GHz band: max. 100 mW
BE
BG
CZ
ES
FR
HR
HU
MT
NL
SK
FI
SE
5 GHz Wi-Fi: for indoor use only
y
DK
IT
AT
UK
DE
CY
PL
NO
EE
LV
PT
CH
IE
LT
RO
TR
EL
LU
SI
Hood control
eHood control
Ho d cont r ol
You can connect this appliance to a suitable extractor
hood and then control the functions of the hood via your
hob.
You have various options for connecting the appliances
together:
Home Connect
Two appliances can be connected using the Home
Connect app provided that both of them are Home
Connect-compatible.
Both appliances can be controlled via the app and via
the control panel.
Refer to the Home Connect documents supplied and
the Home Connect section for more information.
~ "Home Connect" on page 36
en
Connecting appliances via your home network
Use this type of connection if neither or one of the two
appliances is connected to the Home Connect app.
If the appliances are connected to each other via your
home network, you can use both the hood controls and
Home Connect to operate the hob.
Notes
■
Make sure you follow the safety instructions in the
instruction manual for your extractor hood and that
these are complied with even when operating the
appliance via the hood controls on the
hob.~ "Important safety information" on page 6
■
If the appliance is being operated by means of the
controls on the extractor hood, this mode of
operation always has priority. It is not possible to use
the hood controls on the hob during this time.
■
In networked standby mode, your appliance requires
a maximum of 2 W.
Setting up
To set up the connection between the hob and the
extractor hood, the hob must be switched on.
Connecting appliances directly
If the appliance is connected directly to an extractor
hood, the extractor hood can be controlled via the hob.
It is then not possible for either of the appliances to
connect to your home network or to the app. Both
appliances can be controlled via the control panel.
Connecting directly
Make sure that the extractor hood is switched off.
For more information refer to the section entitled
"Connecting to the hob" in the instruction manual for
your extractor hood.
Note:
If you connect your hob directly to the extractor hood, it
cannot be connected to your home network as well and
you will not be able to use Home Connect.
1. Touch the
® symbol in the docking menu to open
the basic settings.
2. Select the Hood control cookConnect hood control
setting.
3. Touch "Connect directly".
4. You have 2 minutes to initiate the connection
process on the extractor hood.
A message is displayed to notify you when the hob is
successfully connected to the extractor hood. The
symbols for the hood controls on the hob are displayed
on the main screen.
41
en
Hood control
Connecting via your home network
You require a router that has WPS functionality.
Access to your router is required. If you do not have
this, follow the steps listed under "Direct connection".
When you begin, make sure that the extractor hood is
connected to the same home network.
Control the hood via the hob
1. Touch the
Setting the fan
® symbol in the docking menu to open
the basic settings.
2. Select the Hood control cookConnect hood control
setting.
3. Touch "Connect to network".
4. Press the WPS button on the router within the next
2 minutes.
A message will be displayed to notify you when the
hob is successfully connected to your home
network.
5. You have 2 minutes to initiate the connection
process on the extractor hood.
A message is displayed to notify you when the hob is
successfully connected to the extractor hood. The
symbols for the hood controls on the hob are displayed
on the main screen.
Note:
Connection can only be established when both
appliances are connected to your home network and
the connection process has been initiated for both of
them. If the time allowed for connecting has already
expired for one of the two appliances, initiate the
connection process again.
Disconnecting from the network
Di scon ect i ng f r om t he net wor k
You can reset the connections you have saved for your
home network and extractor hood at any time.
1. Touch the
e symbol in the docking menu to open
the basic settings.
2. Touch the "Hood control" setting.
3. Touch "Disconnect".
The connection has been restored.
42
In the basic settings of your hob you can adjust the
behaviour of your extractor hood depending on the
switch-on/off of the hob or individual cooking zones.
~ "Hood control settings" on page 43
You can select other settings using the control panel.
Activation
1. Touch the
I symbol in the settings area.
The preset fan setting is shown on the display.
2. Select the fan setting you require.
Touch int 1 or int 2 to select one of the intensive
modes.
The fan has been activated.
Deactivating
1. Touch the I symbol in the settings area.
2. Select fan setting 0.
The fan has been deactivated.
Setting automatic mode
Activation
1. Touch the I symbol in the settings area.
2. Select !.
Automatic mode is activated.
The fan starts automatically when steam is produced.
Deactivating
1. Touch the I symbol in the settings area.
2. Select fan setting 0.
Automatic mode is deactivated.
Setting the hood lighting
The hood light can be switched on and off using the
control panel on the hob.
Touch the = symbol on the main screen.
Hood control
en
Hood control settings
Ho d cont r ol set i ngs
You can adapt the hood controls on the hob to suit your
needs at any time.
Note:
The settings will only be displayed if the appliance is
connected to an extractor hood.
Ajustes
Fan control
Fan run-on
Automatic light on
Automatic light off
Disconnect
*Factory settings
Descripción y opciones
If you wish, you can set the fan to start up after the hob is switched on, and you can configure the settings
depending on how you want the fan to run.
■
Switched off: You will need to switch the hood on manually when needed.
■
Switched on in automatic mode*: The hood switches on when setting an independent hob in automatic mode.
■
Switch on in standard fan run-on*: The hood switches on when setting an independent hob to a fixed
setting.
The fan continues running to ensure that residual odours are eliminated. The fan will switch off automatically afterwards.
■
Off
■
Switch on in automatic mode.*
■
Switch on in standard fan run-on.
■
No change: The fan settings will not change if you switch off the hob.
If you wish, you can set the hood light to automatically come on when the hob is switched on.
■
On* – The light switches on when you switch on the hob.
■
Off
You can specify whether you want the hood lighting to be switched off automatically when you switch off
the hob.
■
Deactivated*
■
Activated: The lighting switches off when the hob is switched off.
You can delete the connections to your home network and extractor hood that you have saved at any time.
--------
43
en
Maximum power consumption
hMaximum power
consumption
You can use the Maximum power consumption
function to set the total power of the hob.
The hob settings are preconfigured at the factory. Its
maximum performance is specified on the rating plate.
You can use the power manager function to change the
value to meet the requirements of the specific electrical
installation.
To ensure that this set value is not exceeded, the hob
has a series of components that intelligently and
automatically share the available power between the
cooking zones that are switched on.
While the Maximum power consumption function is
activated, the output of a cooking zone may temporarily
fall below the nominal value. If a cooking zone is
switched on and maximum power has been reached, a
corresponding message appears in the display. The
appliance controls and selects the highest power level
automatically.
For more information about how the total power of the
hob is changed, see the section entitled ~ "Basic
settings"
DCleaning
Suitable maintenance and cleaning products can be
purchased from the after-sales service or in our e-Shop.
Cl eani ng
Maxi mu power consumpt i on
Hob
Cleaning
Always clean the hob after cooking. This will prevent
food deposits from becoming burned on. Only clean the
hob after the residual heat indicator has gone out.
Clean the hob with a damp dish cloth and dry it with a
cloth or towel to prevent limescale build-up.
Only use cleaning agents that are suitable for this type
of hob. Observe the manufacturer's instructions on the
product packaging.
Never use:
■
■
■
■
■
■
Undiluted washing-up liquid
Cleaning agents designed for dishwashers
Abrasive cleaners
Harsh cleaning agents, such as oven spray and
limescale remover
Scouring pads
High-pressure cleaners or steam jet cleaners
Stubborn dirt is best removed with a glass scraper,
available from retailers. Observe the manufacturer's
instructions.
You can obtain a suitable glass scraper from customer
services or through our online shop.
Using a special sponge for cleaning glass-ceramic
hobs achieves a great cleaning result.
Potential marks
Limescale and water
marks
Clean the hob as soon as it has cooled down.
You can use a cleaning agent suitable for
glass-ceramic hobs.*
Sugar, rice starch or Clean immediately. Use a glass scraper. Cauplastic
tion: Risk of burns.*
* Then clean with a damp dish cloth and dry with a cloth or towel.
Note: Do not use any cleaning agents while the hob is
still hot. This may mark the surface. Make sure that any
residue left by cleaning agents is removed.
Hob surround
To prevent damage to the hob surround, observe the
following instructions:
■
■
■
■
44
Only use warm soapy water
Wash new dish cloths thoroughly before use.
Do not use harsh or abrasive cleaning agents.
Do not use a glass scraper or sharp objects.
Frequently Asked Questions (FAQ)
en
{Frequently Asked
Questions (FAQ)
Fr equent l y Asked Quest i ons ( FAQ)
Use
Nothing appears in the display.
The brightness may not be set correctly. Look at the display from above and set the brightness in the basic settings.
For more information about the settings, see the section entitled ~ "Basic settings".
The main display shows a warning message and a signal tone sounds.
Remove any liquid or remnants of food from the control panel. Remove any objects from the control panel.
For instructions on how to deactivate the signal tone, see the section entitled ~ "Basic settings".
--------
Noises
Why can I hear noises while I'm cooking?
Noises may be generated while using the hob depending on the base material of the cookware. These noises are normal for induction
technology. They do not indicate that there is a fault.
Possible noises:
A low humming noise of the kind a transformer makes:
Occurs when cooking at a high power level. The noise disappears or becomes quieter when the power level is reduced.
Quiet humming:
The cookware may be too small for the cooking position or not suitable for induction cooking. Use a bigger item of cookware or move it to
a different position on the cooking surface.
Quiet whistling:
This happens when the cookware is empty. The noise disappears when water or food is added to the cookware.
High-pitched whistling noises:
These may occur if two cooking positions are used at the highest power level at the same time. The whistling noises disappear or become
quieter when the power level is reduced.
Crackling:
This occurs when using cookware made from layers of different material or when using cookware of different sizes and different materials
at the same time. How loud the noise is may vary depending on the quantity of food you are cooking and the method you are using.
Fan noise:
The hob is equipped with a fan that automatically switches on at high temperatures. The fan may continue to run even after you have
switched off the hob if the temperature detected is still too high.
--------
Clicking:
Occasional clicking when activating or moving an item of cookware is completely normal.
Now and again, other completely random noises that have nothing to do with the cookware may occur.
45
en
Frequently Asked Questions (FAQ)
Cookware
Which types of cookware can be used with an induction hob?
For information on which types of cookware can be used with an induction hob, see the section entitled ~ "Induction cooking".
Why is the hob not heating up?
Make sure that the cookware is suitable for use with an induction hob. For information on the type, size and positioning of the cookware,
see the section entitled ~ "Induction cooking".
Why is it taking so long for the cookware to heat up or why is it not heating up correctly despite being on a high power level?
Make sure that the cookware is suitable for use with an induction hob. For information on the type, size and positioning of the cookware,
see the section entitled ~ "Induction cooking".
The depiction of the cookware on the touchscreen display does not match the actual cookware in terms of size and shape.
The depiction of the cookware on the touchscreen display is purely indicative.
Make sure that the item of cookware is inside the usable area of the cooking surface.
There is cookware on the cooking surface that is not being shown on the touchscreen display.
There are more than eight items of cookware on the cooking surface.
The cookware is too small: A diameter of between 90 and 340 mm is recommended.
Use a bigger item of cookware or cookware that is suitable for induction cooking. Alternatively, move the cookware to a different position
on the cooking surface. For information on which types of cookware can be used with an induction hob, see the section entitled
~ "Induction cooking".
There are two items of cookware on the cooking surface. However, the touchscreen display displays this as just one item of cookware.
If two pots or pans are placed very close together on the cooking surface, the touchscreen display may depict them as one item of cookware.
Move the two items away from each other until the touchscreen display depicts them separately.
There is an item of cookware on the cooking surface. However, the touchscreen display depicts two or more.
The base of the cookware may be deformed or embossed, or the cookware is not suitable for induction cooking.
Check how flat the base of the cookware is and place it back on the cooking surface. For information on the type, size and positioning of
the cookware, see the section entitled ~ "Induction cooking".
Not every item of cookware that is on the cooking surface can be activated.
You can place up to eight items of cookware on the cooking surface but only up to five evenly distributed items can be used at the same
time.
For information on how to position the cookware, see the section entitled ~ "Induction cooking"
You can cook with up to three items of cookware on each side. If there is an item of cookware in the centre of the cooking surface or an
item of cookware is too large, the number of "active" pots or pans is restricted.
For information on how to position the cookware, see the section entitled ~ "Induction cooking"
One of the items of cookware is not suitable for induction cooking. The : symbol appears on the touchscreen display next to the unsuitable pot or pan.
For information on which items of cookware are suitable for induction cooking, see the section entitled ~ "Induction cooking"
The appliance has exceeded its maximum power consumption or the Maximum power consumption setting has been activated.
Check the installation and configure the Maximum power consumption setting correctly. See the section entitled ~ "Basic settings"
The power level cannot be increased.
The appliance has reached its maximum power consumption or the Maximum power consumption setting has been activated.
Change how the items of cookware are arranged on the cooking surface. Check the installation and configure the Maximum power consumption setting correctly. See the section entitled ~ "Basic settings"
The cooking sensor is not available.
The appliance has reached its maximum power consumption or the Maximum power consumption setting has been activated.
To make the cooking sensor ready to use, reduce or switch off the power levels for the other pans. Change how the items of cookware are
arranged on the cooking surface. Check the installation and configure the Maximum power consumption setting correctly. See the section
entitled ~ "Maximum power consumption"
46
Frequently Asked Questions (FAQ)
en
If you use the appliance intensively, this may increase the required cooking times.
This may be due to the fact that internal safety mechanisms are preventing the cooker from overheating.
Try moving the cookware to a different position.
Bubbles are forming with an uneven distribution within the cookware.
Depending on the power level that is selected, the type of cookware or the combination with other cookware, bubbles may form unevenly.
This does not affect the temperature or the cooking process.
For information on the type, size and positioning of the cookware, see the section entitled ~ "Induction cooking"
--------
Cleaning
How do I clean the hob?
You can achieve the best results by using special glass-ceramic cleaning products. Do not use any harsh or abrasive cleaning products,
dishwater detergent (concentrated) or scouring pads.
For more information on cleaning and caring for your hob, see the section entitled ~ "Cleaning".
--------
Home network
Why will the hob not connect to the home network after the WPS button has been pressed on the router?
Once the "Connect automatically" option has been selected, press the WPS button on the router within the next two minutes.
If this time has already elapsed, repeat the connection procedure. If the problems persist, restore the appliance to factory settings; see
section ~ "Basic settings".
Why is my mobile device not logging into the Home Connect network?
Use the SSID "HomeConnect" and password "HomeConnect" to connect.
Make sure that you have entered all the characters correctly and that you have used upper and lower case in the relevant places.
--------
47
en
Trouble shooting
Information, warnings and fault codes
3Trouble shooting
Faults often have simple explanations. Please read the
information and tips provided below before calling the
after-sales service.
Tr oubl e sho t i ng
In the event of a problem, information, warnings or fault
codes will automatically appear on the display. Follow
the instructions on the touchscreen display to rectify the
problem.
Notes
■
A fault code will also be displayed with some
warnings. If necessary, provide the after-sales
service with the fault code.
■
If a fault occurs, the appliance will not switch to
standby mode.
Tips
Problem
The hob will not switch on.
The touchscreen display is not responding or has frozen.
The cooking zone's power level cannot be increased.
An audible signal will sound if there is something on the touchscreen display.
The hob is responding in an unusual manner or cannot be operated properly.
The electronics have overheated and have switched off the
affected cooking zone.
The electronics have overheated and all the cooking zones have
been switched off.
There is hot cookware near the control panel. The cooking zone
has been switched off to protect the electronics.
The cooking zone has overheated and has been switched off to
protect the work surface.
The transfer settings function cannot be activated.
Solution
Use other electrical appliances to check whether a short circuit has occurred in
the power supply.
Make sure that you have connected the appliance as shown in the circuit diagram.
If you are unable to rectify the fault, contact our technical after-sales service.
The control panel is damp or there is something on it. Dry the control panel or
remove the object.
The hob's total power output has been limited. Change the total power under Maximum power consumption in the basic settings.
If a very large item of cookware is being used, this may have an effect on the maximum power level for that half of the hob. Set the cookware down again.
Remove the object and reconfigure the hob settings.
Do not place hot cookware on the control panel.
Switch the appliance off using the main fuse or the circuit breaker in the fuse box.
Wait a few seconds before reconnecting the appliance.
Wait until the electronics have cooled down sufficiently. When the fault indicator
goes out, you can continue cooking.
Remove the cookware that is causing the problem. Wait a few seconds. When the
fault indicator goes out, you can continue cooking.
Wait until the electronics have cooled down sufficiently. Then switch the cooking
zone on again.
You have removed the active item of cookware from its position and set a pot or
pan of a different size down instead. Test with the same item of cookware.
The hob has been operating continuously for an extended period. The automatic safety cut-out function has been activated. See the section entitled
~ "Automatic safety cut-out"
The activeLight light strips at the sides are not lighting up.
Contact our technical after-sales service.
The cooking sensor has overheated and the cooking zone has
Wait until the temperature sensor has cooled down sufficiently. Then reactivate
been switched off. E8202
the function.
The cooking sensor has overheated and the adjacent cooking
If you are not using the cooking sensor, remove it from the cookware and keep it
zones have been switched off. E8203
away from other cooking zones or heat sources. Switch the cooking zones on
again.
The battery in the cooking sensor is almost flat. E8204
Replace the 3 V CR2032 battery. See the section entitled ~ "Changing the
battery"
The connection to the cooking sensor has been broken. E8205 Switch the function off and then on again.
The cooking sensor is broken/faulty. E8206
Contact our technical after-sales service.
48
Trouble shooting
en
Problem
The cooking sensor indicator will not light up and the cooking
sensor is not responding.
Solution
Replace the 3 V CR2032 battery. See the section entitled ~ "Changing the
battery"
If this does not solve the problem, press and hold the symbol on the cooking sensor for 8-10 seconds and then reconnect the cooking sensor to the hob. See the
section entitled ~ "Connecting the wireless temperature sensor to the control
panel"
If the problem persists, contact our technical after-sales service.
The indicator on the sensor flashes twice. The battery in the cook- Replace the 3 V CR2032 battery. See the section entitled ~ "Changing the
ing sensor is almost flat. You may be interrupted the next time you battery"
cook by the battery running out.
The indicator on the sensor flashes three times. The connection Press and hold the symbol on the cooking sensor for 8-10 seconds and then
to the cooking sensor has been broken.
reconnect the cooking sensor to the hob. See the section entitled ~ "Connecting
the wireless temperature sensor to the control panel"
The hob is unable to connect to your home network or the extrac- Switch the hob off and then on again.
tor hood. E7010
If the message appears again, contact our technical after-sales service.
The operating voltage is incorrect and outside of the normal oper- Contact your electricity supplier.
ating range. E9000/E9010
The hob is not connected correctly U400
Disconnect the hob from the mains. Make sure that you have connected the hob
as shown in the circuit diagram.
Demo mode
If the ± symbol is shown on the display, demo mode
is active. The appliance does not heat up in demo
mode. Disconnect the appliance from the power
supply.Wait a few seconds before reconnecting the
appliance. Then deactivate demo mode in the basic
settings within 3 minutes of switching on the appliance.
49
en
Customer service
4Customer service
Our after-sales service is there for you if your appliance
needs to be repaired. We will always find an
appropriate solution, also in order to avoid after-sales
personnel having to make unnecessary visits.
Cust omer ser vi ce
E number and FD number
Please quote the E number (product number) and the
FD number (production number) of your appliance
when contacting the after-sales service.
The rating plate bearing these numbers can be found:
■
■
On the appliance certificate.
On the lower section of the hob.
The E-number can also be found on the glass surface
of the hob. You can check the customer index (KI) and
FD number by going to the basic settings. Look up
section~ "Basic settings" for this.
Please note that a visit from an after-sales service
engineer is not free of charge in the event of misuse of
the appliance, even during the warranty period.
Please find the contact data of all countries in the
enclosed customer service list.
To book an engineer visit and product advice
GB
0344 892 8999
Calls charged at local or mobile rate.
IE
01450 2655
0.03 € per minute at peak. Off peak 0.0088 €
per minute.
Rely on the professionalism of the manufacturer. You
can therefore be sure that the repair is carried out by
trained service technicians who carry original spare
parts for your appliances.
50
%6++DXVJHUlWH*PE+
&DUO:HU\6WU0QFKHQ
*(50$1<
VLHPHQVKRPHEVKJURXSFRP
0DQXIDFWXUHGE\%6++DXVJHUlWH*PE+XQGHU7UDGHPDUN/LFHQVHRI6LHPHQV$*
*9001351343*
9001351343
980903(00)
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising