Siemens | LC60BA530 | Instruction manual | Siemens iQ100 Chimney hood Instruction manual

Siemens iQ100 Chimney hood Instruction manual
Extractor hood
LC60BA530, LC90BA530
siemens-home.bsh-group.com/welcome
siemens-home.com/welcome
[en] Instruction manual
Register
your
product
online
Ú Table of contents
e[nuoIrs]ctimanul
Important safety information.....................................................3
Environmental protection ..........................................................4
Saving energy......................................................................................4
Environmentally-friendly disposal.....................................................4
Operating mode..........................................................................4
Exhaust air mode ................................................................................4
Operating the appliance ............................................................5
Controls ................................................................................................5
Lighting .................................................................................................5
Cleaning and maintenance ........................................................5
Removing and installing the filter ....................................................6
Trouble shooting ........................................................................ 6
LED lights .............................................................................................6
Fault table.............................................................................................6
After-sales service ..................................................................... 7
Special accessories ................................................................... 7
Produktinfo
Additional
information on
on products,
products, accessories,
accessories, replacement
replacement
Additional information
parts and
and services
services can
can be
be found
found at
at www.siemens-home.bshwww.siemens-home.com
parts
group.com
and in shop
the online
shop www.siemens-home.bshand in the online
www.siemens-eshop.com
group.com/eshops
Important safety information
Read these instructions carefully. Only then will you be able to
operate your appliance safely and correctly. Retain the
instruction manual and installation instructions for future use or
for subsequent owners.
The appliance can only be used safely if it is correctly installed
according to the safety instructions. The installer is responsible
for ensuring that the appliance works perfectly at its installation
location.
This appliance is intended for domestic use and the household
environment only. The appliance is not intended for use
outside. Do not leave the appliance unattended during
operation. The manufacturer is not liable for damage which is
caused by improper use or incorrect operation.
This appliance is intended for use up to a maximum height of
2000 metres above sea level.
This appliance is not intended for use by persons (including
children) with reduced physical, sensory or mental capabilities,
or lack of experience and knowledge, unless they have been
given supervision or instruction concerning use of the
appliance by a person responsible for their safety.
Room air-dependent heat-producing appliances (e.g. gas, oil,
wood or coal-operated heaters, continuous flow heaters or
water heaters) obtain combustion air from the room in which
they are installed and discharge the exhaust gases into the
open air through an exhaust gas system (e.g. a chimney).
In combination with an activated vapour extractor hood, room
air is extracted from the kitchen and neighbouring rooms - a
partial vacuum is produced if not enough fresh air is supplied.
Toxic gases from the chimney or the extraction shaft are
sucked back into the living space.
■
■
Adequate incoming air must therefore always be ensured.
An incoming/exhaust air wall box alone will not ensure
compliance with the limit.
Safe operation is possible only when the partial vacuum in the
place where the heat-producing appliance is installed does not
exceed 4 Pa (0.04 mbar). This can be achieved when the air
needed for combustion is able to enter through openings that
cannot be sealed, for example in doors, windows, incoming/
exhaust air wall boxes or by other technical means.
Children must not play with, on, or around the appliance.
Children must not clean the appliance or carry out general
maintenance unless they are at least 8 years old and are being
supervised.
Keep children below the age of 8 years old at a safe distance
from the appliance and power cable.
Check the appliance for damage after unpacking it. Do not
connect the appliance if it has been damaged in transport.
This appliance is not intended for operation with an external
clock timer or a remote control.
: Danger of suffocation!
Packaging material is dangerous to children. Never allow
children to play with packaging material.
In any case, consult your responsible Master Chimney Sweep.
He is able to assess the house's entire ventilation setup and will
suggest the suitable ventilation measures to you.
Unrestricted operation is possible if the vapour extractor hood
is operated exclusively in the circulating-air mode.
: Risk of fire!
■
: Danger of death!
Risk of poisoning from flue gases that are drawn back in.
Always ensure adequate fresh air in the room if the appliance is
being operated in exhaust air mode at the same time as room
air-dependent heat-producing appliance is being operated.
Grease deposits in the grease filter may catch fire.
Replace the grease filter at least every two months.
Never operate the appliance without the grease filter.
Grease deposits in the grease filter may catch fire. Never
work with naked flames close to the appliance (e.g.
flambéing). Do not install the appliance near a heatproducing appliance for solid fuel (e.g. wood or coal) unless
a closed, non-removable cover is available. There must be no
flying sparks.
Hot oil and fat can ignite very quickly. Never leave hot fat or
oil unattended. Never use water to put out burning oil or fat.
Switch off the hotplate. Extinguish flames carefully using a lid,
fire blanket or something similar.
Risk of fire!
■
Risk of fire!
■
Risk of fire!
3
■
When gas burners are in operation without any cookware
placed on them, they can build up a lot of heat. A ventilation
appliance installed above the cooker may become damaged
or catch fire. Only operate the gas burners with cookware on
them.
Operating several gas burners at the same time gives rise to
a great deal of heat. A ventilation appliance installed above
the cooker may become damaged or catch fire. Never
operate two gas burners simultaneously on the highest flame
for longer than 15 minutes. One large burner of more than 5
kW (wok) is equivalent to the power of two gas burners.
: Risk of electric shock!
■
Risk of fire!
■
: Risk of burns!
A defective appliance may cause electric shock. Never switch
on a defective appliance. Unplug the appliance from the
mains or switch off the circuit breaker in the fuse box.
Contact the after-sales service.
Incorrect repairs are dangerous. Repairs may only be carried
out and damaged power cables replaced by one of our
trained after-sales technicians. If the appliance is defective,
unplug the appliance from the mains or switch off the circuit
breaker in the fuse box. Contact the after-sales service.
Do not use any high-pressure cleaners or steam cleaners,
which can result in an electric shock.
Risk of electric shock!
■
Risk of electric shock!
■
The accessible parts become very hot when in operation. Never
touch hot parts. Keep children at a safe distance.
Causes of damage
: Risk of injury!
Caution!
■
Components inside the appliance may have sharp edges.
Wear protective gloves.
Items placed on the appliance may fall down. Do not place
any objects on the appliance.
The light emitted by LED lights is very dazzling, and can
damage the eyes (risk group 1). Do not look directly into the
switched on LED lights for longer than 100 seconds.
Risk of injury!
■
Risk of injury!
■
Risk of damage due to corrosion. Always switch on the
appliance while cooking to avoid condensation. Condensate
can produce corrosion damage.
Risk of damage due to ingress of humidity into the electronic
circuitry. Never clean operator controls with a wet cloth.
Surface damage due to incorrect cleaning. Clean stainless
steel surfaces in the direction of the grain only. Do not use any
stainless steel cleaners for operator controls.
Surface damage due to strong or abrasive cleaning agents.
Never use strong and abrasive cleaning agents.
Risk of damage from returning condensate. Install the exhaust
duct in such a way that it falls away from the appliance slightly
(1° slope).
Environmental protection
Your new appliance is particularly energy-efficient. Here you
can find tips on how to save even more energy when using the
appliance, and how to dispose of your appliance properly.
Saving energy
■
■
■
■
During cooking, ensure that there is a sufficient supply of air
so that the extractor hood can work efficiently and with a low
level of operating noise.
Adjust the fan speed to the intensity of the cooking fumes.
Only use intensive mode where this is required. A lower fan
speed means that less energy is consumed.
If there are intensive cooking fumes, select a higher fan
speed in good time. If cooking fumes have already spread in
the kitchen, the extractor hood must be operated for longer.
■
■
Switch off the lighting if you no longer require it.
Clean and, if required, replace the filter at regular intervals in
order to increase the effectiveness of the ventilation system
and to prevent the risk of fire.
Environmentally-friendly disposal
Dispose of packaging in an environmentally-friendly manner.
This appliance is labelled in accordance with
European Directive 2012/19/EU concerning used
electrical and electronic appliances (waste
electrical and electronic equipment - WEEE). The
guideline determines the framework for the return
and recycling of used appliances as applicable
throughout the EU.
Switch off the extractor hood if you no longer require it.
Operating mode
This appliance can be used in air extraction mode.
Exhaust air mode
The air which is drawn in is cleaned by the
grease filters and conveyed to the exterior
by a pipe system.
4
Note: The air must not be discharged into a flue that is used for
exhausting fumes from appliances burning gas or other fuels
(not applicable to appliances that only discharge the air back
into the room).
Before conveying the exhaust air into a non-functioning smoke
or exhaust gas flue, obtain the consent of the heating engineer
responsible.
Operating the appliance
Note: Switch on the extractor hood when you start cooking and
switch it off again several minutes after you have finished
cooking. This is the most effective way of removing the kitchen
fumes.
Controls
In the control panel, use the buttons to set the appliance's
different functions.
Control panel
Button
Explanation
#
Switches the extractor hood on and off
B
Switches the lighting on and off
Extractor hood
Switching on or off
Press the # button.
%
Note: It can take up to 25 seconds for the backflow preventer
valve to open fully and for the appliance to reach its full
capacity.
Lighting
The lighting will work even if the extractor hood is switched off.
Display
Explanation
Switching on or off
"
Appliance is switched on
Press the B button.
Cleaning and maintenance
: Risk of burns!
The appliance becomes hot during operation. Allow the
appliance to cool down before cleaning.
: Risk of electric shock!
Follow all instructions and warnings included with the cleaning
agents.
Area
Cleaning agent
Stainless steel
Hot soapy water:
Clean with a dish cloth and then dry
with a soft cloth.
Penetrating moisture may result in an electric shock. Clean the
appliance using a damp cloth only. Before cleaning, pull out the
mains plug or switch off the circuit breaker in the fuse box.
Clean stainless steel surfaces in the
grind direction only.
: Risk of electric shock!
Special stainless steel cleaning products are available from our after-sales
service or from specialist retailers.
Apply a very thin layer of the cleaning
product with a soft cloth.
Do not use any high-pressure cleaners or steam cleaners,
which can result in an electric shock.
Cleaning agents
To ensure that the different surfaces are not damaged by using
the wrong cleaning agent, observe the information in the table.
Do not use any of the following:
■
Harsh or abrasive cleaning agents,
■
Cleaning agents with a high alcohol content,
■
Hard scouring pads or cleaning sponges,
■
High-pressure cleaners or steam cleaners.
Painted surfaces
Hot soapy water:
Clean using a damp dish cloth and dry
with a soft cloth/towel.
Do not use any stainless steel cleaners.
Aluminium and plas- Glass cleaner:
tic
Clean with a soft cloth.
Glass
Glass cleaner:
Clean with a soft cloth. Do not use a
glass scraper.
Controls
Hot soapy water:
Clean using a damp dish cloth and dry
with a soft cloth/towel.
Wash new sponge cloths thoroughly before use.
Risk of electric shock caused by penetrating moisture.
Risk of damage to the electronics from
penetrating moisture. Never clean
operating controls with a wet cloth.
Do not use any stainless steel cleaners.
5
Removing and installing the filter
The filter must be serviced regularly in order to guarantee
efficient filtration of odours and grease.
Metal grease filter
The metal grease filters must be cleaned every 100 operating
hours or at least every two months.
: Risk of fire!
Grease deposits in the grease filter may catch fire.
Clean the grease filter at least every 2 months.
Never operate the appliance without the grease filter.
2. Clean the metal grease filters.
3. Clean the inside of the appliance.
Cleaning the metal mesh grease filters
Notes
■ Do not use any aggressive, acidic or alkaline cleaning
agents.
■
■
When cleaning the metal mesh grease filters, also clean the
holder for the metal mesh grease filters in the appliance
using a damp cloth.
The metal mesh grease filters can be cleaned in the
dishwasher or by hand.
Removing metal grease filter
By hand:
The metal grease filters filter the grease out of kitchen steam.
To keep them in good working order, the filters should be
cleaned at least every two months.
Note: You can use a special grease solvent for stubborn dirt. It
can be ordered via the Online Shop.
■
Soak the metal mesh grease filters in a hot soapy solution.
■
Clean the filters with a brush and then rinse them thoroughly.
■
Leave the metal mesh grease filters to drain.
In the dishwasher:
Note: If the metal mesh grease filters are cleaned in the
dishwasher, slight discolouration may occur. This has no effect
on the function of the metal mesh grease filters.
1. Open the lock on the metal grease filters and remove the
filters from the retainer.
■
■
Notes
■
■
Do not clean heavily soiled metal mesh grease filters together
with utensils.
Place the metal mesh grease filters loosely in the dishwasher.
The metal mesh grease filters must not be wedged in.
When you do this, take hold of the metal grease filters from
underneath with your other hand.Make sure that the metal
grease filters do not fall and damage the hob.
Installing the metal mesh grease filter
Fat may accumulate in the bottom of the metal grease
filters. Hold the filters level to prevent fat from dripping out.
2. Fold up metal grease filter and engage the lock.
1. Insert metal grease filter.
Note: Make sure that the filter lock engages properly.
Trouble shooting
Malfunctions often have simple explanations. Please read the
following notes before calling the after-sales service.
Fault table
: Risk of electric shock!
Problem
Possible cause Solution
The appliance
does not work
The plug is not Connect the appliance to
plugged into the the power supply
mains
Incorrect repairs are dangerous. Repairs may only be carried
out and damaged power cables replaced by one of our trained
after-sales technicians. If the appliance is defective, unplug the
appliance from the mains or switch off the circuit breaker in the
fuse box. Contact the after-sales service.
LED lights
Defective LED lights may be replaced by the manufacturer, their
after-sales service or a qualified technician (electrician) only.
The lighting
does not work.
--------
6
Power cut
Check whether other
kitchen appliances are
working
The fuse is
faulty
Check in the fuse box to
make sure that the fuse for
the appliance is in working
order
The LED lights
are defective.
Call the after-sales service.
After-sales service
Our after-sales service is there for you if your appliance needs
to be repaired. We will always find the right solution in order to
avoid unnecessary visits from a service technician.
Please be aware that a visit by an after-sales engineer will be
charged if a problem turns out to be the result of operator error,
even during the warranty period.
When calling us, please give the product number (E no.) and
the production number (FD no.) so that we can provide you with
the correct advice. The rating plate with these numbers can be
found inside the appliance (remove the metal mesh grease
filter to gain access).
Please find the contact data of all countries in the enclosed
customer service list.
You can make a note of the numbers of your appliance and the
telephone number of the after-sales service in the space below
to save time should it be required.
E no.
FD no.
After-sales serviceO
To book an engineer visit and product advice
GB
0344 892 8999
Calls charged at local or mobile rate.
IE
01450 2655
0.03 € per minute at peak. Off peak 0.0088 € per
minute.
Rely on the professionalism of the manufacturer. You can
therefore be sure that the repair is carried out by trained service
technicians who carry original spare parts for your appliances.
Special accessories
(not supplied)
Note: Follow the installation instructions supplied with the
accessories.
Accessory
Order number
Backboard, 60 cm
LZ50660
Backboard, 90 cm
LZ50960
--------
7
BSH Hausgeräte GmbH
Carl-Wery-Straße 34, 81739 München, GERMANY
siemens-home.com
siemens-home.bsh-group.com
0DQXIDFWXUHGE\%6++DXVJHUlWH*PE+XQGHU7UDGHPDUN/LFHQVHRI6LHPHQV$*
*9001104373*
9001104373
960720
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising