Siemens | LC21BA582 | Instruction manual | Siemens iQ700 Chimney hood Instruction manual

Siemens iQ700 Chimney hood Instruction manual
Extractor hood
LC21BA582
siemens-home.bsh-group.com/welcome
siemens-home.com/welcome
>HQ@ ,QVWUXFWLRQPDQXDO
Register
your
product
online
Ú Table of contents
e[nuoIrs]ctimanul
Important safety information.....................................................3
Environmental protection ..........................................................5
Environmentally-friendly disposal.....................................................5
Operating modes........................................................................5
Exhaust air mode ................................................................................5
Circulating-air mode ...........................................................................5
Operation ....................................................................................6
Setting the fan .....................................................................................6
Intensive setting ..................................................................................6
Automatic mode..................................................................................6
Sensor control .....................................................................................6
Lighting .................................................................................................6
Saturation display ...............................................................................7
Audible signal .....................................................................................7
Cleaning and maintenance........................................................ 7
Trouble shooting ........................................................................ 9
After-sales service ..................................................................... 9
Accessories for circulating-air mode ..............................................9
Produktinfo
Additional information
information on
on products,
products, accessories,
accessories, replacement
replacement
Additional
parts and
and services
services can
can be
be found
found at
at www.siemens-home.bshwww.siemens-home.com
parts
group.com
and in shop
the online
shop www.siemens-home.bshand in the online
www.siemens-eshop.com
group.com/eshops
: Important safety information
Read these instructions carefully. Only then
will you be able to operate your appliance
safely and correctly. Retain the instruction
manual and installation instructions for
future use or for subsequent owners.
The appliance can only be used safely if it
is correctly installed according to the safety
instructions. The installer is responsible for
ensuring that the appliance works perfectly
at its installation location.
This appliance is intended for domestic use
and the household environment only. The
appliance is not intended for use outside.
Do not leave the appliance unattended
during operation. The manufacturer is not
liable for damage which is caused by
improper use or incorrect operation.
This appliance may be used by children
over the age of 8 years old and by persons
with reduced physical, sensory or mental
capabilities or by persons with a lack of
experience or knowledge if they are
supervised or are instructed by a person
responsible for their safety how to use the
appliance safely and have understood the
associated hazards.
Children must not play with, on, or around
the appliance. Children must not clean the
appliance or carry out general maintenance
unless they are at least 8 years old and are
being supervised.
Keep children below the age of 8 years old
at a safe distance from the appliance and
power cable.
Check the appliance for damage after
unpacking it. Do not connect the appliance
if it has been damaged in transport.
This appliance is not intended for operation
with an external clock timer or a remote
control.
Danger of suffocation!
Packaging material is dangerous to
children. Never allow children to play with
packaging material.
Danger of death!
Risk of poisoning from flue gases that are
drawn back in.
Always ensure adequate fresh air in the
room if the appliance is being operated in
exhaust air mode at the same time as room
air-dependent heat-producing appliance is
being operated.
Room air-dependent heat-producing
appliances (e.g. gas, oil, wood or coaloperated heaters, continuous flow heaters
or water heaters) obtain combustion air
from the room in which they are installed
and discharge the exhaust gases into the
open air through an exhaust gas system
(e.g. a chimney).
3
In combination with an activated vapour
extractor hood, room air is extracted from
the kitchen and neighbouring rooms - a
partial vacuum is produced if not enough
fresh air is supplied. Toxic gases from the
chimney or the extraction shaft are sucked
back into the living space.
■ Adequate incoming air must therefore
always be ensured.
■ An incoming/exhaust air wall box alone
will not ensure compliance with the limit.
Safe operation is possible only when the
partial vacuum in the place where the heatproducing appliance is installed does not
exceed 4 Pa (0.04 mbar). This can be
achieved when the air needed for
combustion is able to enter through
openings that cannot be sealed, for
example in doors, windows, incoming/
exhaust air wall boxes or by other technical
means.
In any case, consult your responsible
Master Chimney Sweep. He is able to
assess the house's entire ventilation setup
and will suggest the suitable ventilation
measures to you.
Unrestricted operation is possible if the
vapour extractor hood is operated
exclusively in the circulating-air mode.
Risk of fire!
■ Grease deposits in the grease filter may
catch fire.
Clean the grease filter at least every
2 months.
Never operate the appliance without the
grease filter.
■ Grease deposits in the grease filter may
catch fire. Never work with naked flames
close to the appliance (e.g. flambéing). Do
not install the appliance near a heatproducing appliance for solid fuel (e.g.
wood or coal) unless a closed, nonremovable cover is available. There must
be no flying sparks.
Risk of fire!
Risk of fire!
4
Hot oil and fat can ignite very quickly.
Never leave hot fat or oil unattended.
Never use water to put out burning oil or
fat. Switch off the hotplate. Extinguish
flames carefully using a lid, fire blanket or
something similar.
■ When gas burners are in operation without
any cookware placed on them, they can
build up a lot of heat. A ventilation
appliance installed above the cooker may
become damaged or catch fire. Only
operate the gas burners with cookware on
them.
■ Operating several gas burners at the
same time gives rise to a great deal of
heat. A ventilation appliance installed
above the cooker may become damaged
or catch fire. Never operate two gas
burners simultaneously on the highest
flame for longer than 15 minutes. One
large burner of more than 5 kW (wok) is
equivalent to the power of two gas
burners.
Risk of burns!
The accessible parts become very hot when
in operation. Never touch hot parts. Keep
children at a safe distance.
Risk of injury!
■ Components inside the appliance may
have sharp edges. Wear protective gloves.
■ Items placed on the appliance may fall
down. Do not place any objects on the
appliance.
■ The light emitted by LED lights is very
dazzling, and can damage the eyes (risk
group 1). Do not look directly into the
switched on LED lights for longer than
100 seconds.
■
Risk of fire!
Risk of fire!
Risk of injury!
Risk of injury!
Risk of electric shock!
■ A defective appliance may cause electric
shock. Never switch on a defective
appliance. Unplug the appliance from the
mains or switch off the circuit breaker in
the fuse box. Contact the after-sales
service.
■ Incorrect repairs are dangerous. Repairs
may only be carried out and damaged
power cables replaced by one of our
trained after-sales technicians. If the
appliance is defective, unplug the
appliance from the mains or switch off the
circuit breaker in the fuse box. Contact the
after-sales service.
■ Do not use any high-pressure cleaners or
steam cleaners, which can result in an
electric shock.
Risk of electric shock!
Causes of damage
Caution!
Risk of damage due to corrosion. Always switch on the
appliance while cooking to avoid condensation. Condensate
can produce corrosion damage.
Always replace faulty bulbs to prevent the remaining bulbs from
overloading.
Risk of damage due to ingress of humidity into the electronic
circuitry. Never clean operator controls with a wet cloth.
Surface damage due to incorrect cleaning. Clean stainless
steel surfaces in the direction of the grain only. Do not use any
stainless steel cleaners for operator controls.
Surface damage due to strong or abrasive cleaning agents.
Never use strong and abrasive cleaning agents.
Risk of damage from returning condensate. Install the exhaust
duct in such a way that it falls away from the appliance slightly
(1° slope).
Risk of electric shock!
Environmental protection
Environmentally-friendly disposal
Dispose of packaging in an environmentally-friendly manner.
This appliance is labelled in accordance with
European Directive 2012/19/EU concerning used
electrical and electronic appliances (waste electrical
and electronic equipment - WEEE). The guideline
determines the framework for the return and recycling
of used appliances as applicable throughout the EU.
Operating modes
This appliance can be used in exhaust-air mode or circulatingair mode.
Circulating-air mode
The air which is drawn in is cleaned by the
grease filters and an activated carbon filter
and conveyed back into the kitchen.
Exhaust air mode
The air which is drawn in is cleaned by the
grease filters and conveyed to the exterior
by a pipe system.
Note: The exhaust air must not be conveyed into a functioning
smoke or exhaust gas flue or into a shaft which is used to
ventilate installation rooms which contain heat-producing
appliances.
■
■
Before conveying the exhaust air into a non-functioning
smoke or exhaust gas flue, obtain the consent of the heating
engineer responsible.
Notes
■ To bind odours in circulating-air mode, you must install an
activated carbon filter. The different options for operating the
appliance in circulating-air mode can be found in the
brochure. Alternatively, ask your dealer. The required
accessories are available from specialist retailers, from
customer service or from the Online Shop.
■
For appliances with an additional internal filter, only the
CleanAir recirculation module (see Accessories for
circulating-air mode) can be used.
If the exhaust air is conveyed through the outer wall, a
telescopic wall box should be used.
5
Operation
Note: Switch on the extractor hood when you start cooking and
switch it off again several minutes after you have finished
cooking. This is the most effective way of removing the kitchen
fumes.
Control panel
DXWR
Explanation
LQW
Automatic mode
#
Switches the fan on/off
Switching on
=
Switches on the lighting
1. Press the # button.
&
Switches on the Boost function (short-term maximum
power)
2. Press the ! button.
!
Switches on automatic mode with fan run-on
-|||+ Sets the fan level
Setting the fan
Note: Always adjust the fan strength to meet current conditions.
If there is a large build-up of steam or fumes, select a high fan
setting.
Switching on
1. Press the # button.
The fan starts at fan setting ƒ.
The fan starts at fan setting ƒ.
The optimum fan setting ‚, ƒ or „ is set automatically using
a sensor.
Switching off
Press the ! or # button.
Automatic mode is switched off.
The fan switches off automatically if the air quality in the room
falls below a certain level. Automatic mode can run for a
maximum of four hours.
Sensor control
Switching off the appliance
In automatic mode, a sensor in the extractor hood detects the
intensity of the cooking and roasting odours. Depending on the
sensor setting, the fan automatically switches to another fan
setting.
Press the # button.
Default sensitivity setting: „
2. Move your finger over the ||| settings range to set a different
fan setting.
Intensive setting
You can use the intensive setting if there is a large build-up of
odours and fumes/vapours.
Switching on
1. Move your finger to the right over the ||| settings range until
the intensive mode ‚2 is shown in the display panel.
The intensive mode ‚2 is activated.
2. Move your finger to the right over the ||| settings range until
the intensive mode ƒ2 is shown in the display panel.
The intensive mode ƒ2 is activated.
Note: The run time of the intensive mode is
approx. six minutes. Once this time has elapsed, the appliance
switches back to a lower fan setting.
Switching off
Move your finger to the left over the ||| settings range until you
set the required fan setting.
The intensive mode ends.
Boost function
The boost function is a short-term maximum power setting
which can be activated in any fan setting.
Press the & button.
After approx. 20 seconds, the fan switches back to the
previously set fan setting.
6
Lowest sensitivity setting: ‚
Highest sensitivity setting: †
Changing the sensitivity of the sensor
If the sensor control reacts too quickly or too slowly, change
the sensitivity setting.
1. When the fan is switched off, press and hold the ! button
for approx. four seconds.
The setting is displayed.
2. Move your finger to the left or right over the ||| settings
range to change the sensitivity setting.
3. Press and hold the ! button for approx. four seconds.
The change is saved.
Lighting
The lighting can be switched on and off independently of the
ventilation system.
Switching on or off
Press the = button.
Setting the brightness
Press and hold the = button until the required brightness is
reached.
Saturation display
When the metal grease filters or the activated charcoal filter
are/is saturated, a signal sounds for approx. four seconds after
the fan is switched off.
The corresponding symbols appear in the display panel:
■
Metal grease filter: !
■
Activated charcoal filter: "
■
Metal grease filter and activated charcoal filter: ! and "
flash alternately
If you have not yet done so, carry out the following steps now:
■
■
Clean the metal grease filters or replace the activated
charcoal filters; see section Cleaning and maintenance or the
"CleanAir air recirculation module" printed supplement.
Reset the saturation indicator; see section Cleaning and
maintenance.
Resetting the saturation displays
Press and hold the - button until the saturation indicator no
longer flashes.
The saturation indicator is reset.
Switching over the display for circulating-air mode
Starter set for circulating-air mode
For air recirculation, the electronic control display must be
switched over accordingly:
1. Check whether the extractor hood is connected and switched
off.
2. Press the # and ! buttons at the same time until ™"
lights up in the display panel.
The electronic control is switched over to air recirculation.
CleanAir recirculation module
For air recirculation, the electronic control display must be
switched over accordingly:
1. Check whether the extractor hood is connected and switched
off.
2. Press the # and ! buttons at the same time until ™"
lights up in the display panel.
3. Press the # and ! buttons at the same time until ’"
lights up in the display panel.
The electronic control is switched over to air recirculation.
Switching over the display for exhaust air mode
1. Check whether the extractor hood is connected and switched
off.
2. Press the # and ! buttons at the same time until ! lights
up in the display panel.
The electronic control is switched back to air extraction.
Audible signal
Switching on
1. Switch off the fan.
2. Press and hold the # and + buttons until an audible signal
sounds.
The audible signal is switched on.
Switching off
1. Switch off the fan.
2. Press and hold the # and + buttons until an audible signal
sounds.
The audible signal is switched off.
Cleaning and maintenance
: Risk of burns!
The appliance will become hot during operation, especially
near the bulbs. Allow the appliance to cool down before
cleaning.
: Risk of electric shock!
Follow all instructions and warnings included with the cleaning
agents.
Area
Cleaning agents
Stainless steel
Hot soapy water:
Clean with a dish cloth and dry with a
soft cloth.
Penetrating moisture may result in an electric shock. Clean the
appliance using a damp cloth only. Before cleaning, pull out the
mains plug or switch off the circuit breaker in the fuse box.
Clean stainless steel surfaces in the
direction of the grain only.
Special stainless steel cleaning products are available from our after-sales
service or from specialist retailers.
Apply a very thin layer of the cleaning
product with a soft cloth.
: Risk of electric shock!
Do not use any high-pressure cleaners or steam cleaners,
which can result in an electric shock.
: Risk of injury!
Components inside the appliance may have sharp edges. Wear
protective gloves.
Cleaning agents
Observe the information in the table to ensure that the different
surfaces are not damaged by using the wrong type of cleaning
agent. Do not use
■
harsh or abrasive cleaning agents,
■
cleaning agents with a high concentration of alcohol,
■
hard scouring pads or sponges,
■
high-pressure cleaners or steam cleaners.
Painted surfaces
Hot soapy water:
Clean using a damp dish cloth and dry
with a soft cloth/towel.
Do not use any stainless steel cleaners.
Aluminium and plas- Glass cleaner:
tic
Clean with a soft cloth.
Glass
Glass cleaner:
Clean with a soft cloth. Do not use a
glass scraper.
Wash new sponge cloths thoroughly before use.
7
Area
Cleaning agents
Operating controls
Hot soapy water:
Clean using a damp dish cloth and dry
with a soft cloth.
Risk of damage to the electronics from
penetrating moisture. Never clean operator controls with a wet cloth.
Do not use any stainless steel cleaners.
Removing metal grease filter
Cleaning the metal mesh grease filters
: Risk of fire!
Grease deposits in the grease filter may catch fire.
Clean the grease filter at least every 2 months.
Never operate the appliance without the grease filter.
Notes
Do not use any aggressive, acidic or alkaline cleaning
agents.
■
■
1. Open the lock and fold down the metal grease filter. While
doing this, place your other hand under the metal grease
filter.
■
2. For edge extraction filters, pull the metal grease filter
downwards. While doing this, place your other hand under
the metal grease filter.
The metal mesh grease filters can be cleaned in the
dishwasher or by hand.
In the dishwasher:
Note: If the metal mesh grease filters are cleaned in the
dishwasher, slight discolouration may occur. This has no effect
on the function of the metal mesh grease filters.
■
■
For additional filters, open the lock and fold down the metal
grease filter. While doing this, place your other hand under
the metal grease filter.
When cleaning the metal mesh grease filters, also clean the
holder for the metal mesh grease filters in the appliance
using a damp cloth.
Do not clean heavily soiled metal mesh grease filters together
with utensils.
Place the metal mesh grease filters loosely in the dishwasher.
The metal mesh grease filters must not be wedged in.
By hand:
Note: You can use a special grease solvent for stubborn dirt. It
can be ordered via the Online Shop.
■
Soak the metal mesh grease filters in a hot soapy solution.
■
Clean the filters with a brush and then rinse them thoroughly.
■
Leave the metal mesh grease filters to drain.
Installing the metal mesh grease filter
1. Insert the metal mesh grease filter.
Notes
■
■
Grease may accumulate in the bottom of the metal grease
filter.
Hold the metal grease filter level to prevent grease from
dripping out.
3. Clean the metal grease filter.
8
While doing this, place the other hand under the metal mesh
grease filter.
2. Fold the metal mesh grease filter upwards, locking it in place.
Trouble shooting
Malfunctions often have simple explanations. Please read the
following notes before calling the after-sales service.
: Risk of electric shock!
Incorrect repairs are dangerous. Repairs may only be carried
out and damaged power cables replaced by one of our trained
after-sales technicians. If the appliance is defective, unplug the
appliance from the mains or switch off the circuit breaker in the
fuse box. Contact the after-sales service.
LED lights
Defective LED lights must only be replaced by the
manufacturer, their customer service department or a licensed
technician (electrician).
Fault table
Fault
Possible cause
Solution
The appliance does not work
The plug is not plugged into the mains
Connect the appliance to the power
supply
Power cut
Check whether other kitchen appliances
are working
The fuse is faulty
Check in the fuse box to make sure that
the fuse for the appliance is in working
order
The lighting does not work
The bulbs are faulty
Call the after-sales service
! flashes in the display panel.
The metal grease filter is saturated.
Clean the filter; see section Cleaning
and maintenance.
" flashes in the display panel.
The activated charcoal filter is saturated. Replace the filter; see the "CleanAir air
recirculation module" printed supplement.
--------
After-sales service
Our after-sales service is there for you if your appliance needs
to be repaired. We will always find the right solution in order to
avoid unnecessary visits from a service technician.
Accessories for circulating-air mode
When calling us, please give the product number (E no.) and
the production number (FD no.) so that we can provide you with
the correct advice. The rating plate with these numbers can be
found inside the appliance (remove the metal mesh grease
filter to gain access).
Notes
■ Follow the installation instructions supplied with the
accessories.
You can make a note of the numbers of your appliance and the
telephone number of the after-sales service in the space below
to save time should it be required.
E no.
(not included in the delivery)
■
For appliances with an additional internal filter, only the
CleanAir recirculation module can be used.
Basic equipment: Starter set for circulating-air mode - narrow
1
FD no.
After-sales serviceO
Please be aware that a visit by an after-sales engineer will be
charged if a problem turns out to be the result of operator error,
even during the warranty period.
Please find the contact data of all countries in the enclosed
customer service list.
To book an engineer visit and product advice
GB
0344 892 8999
Calls charged at local or mobile rate.
IE
01450 2655
0.03 € per minute at peak. Off peak 0.0088 € per
minute.
Throw-away filter
2
Rely on the professionalism of the manufacturer. You can
therefore be sure that the repair is carried out by trained service
technicians who carry original spare parts for your appliances.
9
Basic equipment: Starter set for circulating-air mode - wide
3
Throw-away filter
4
Basic equipment: CleanAir recirculation module - narrow
5
Throw-away filter
6
Basic equipment: CleanAir recirculation module - wide
7
Throw-away filter
8
1
LZ53250 channel width 260 mm
2
LZ53251 channel width 260 mm
3
LZ53450 channel width 345 mm
4
LZ53451 channel width 345 mm
5
LZ57000 channel width 260 mm
6
LZ56200 channel width 260 mm
7
LZ57300 channel width 345 mm
8
LZ56200 channel width 345 mm
10
BSH Hausgeräte GmbH
Carl-Wery-Straße 34, 81739 München, GERMANY
siemens-home.com
siemens-home.bsh-group.com
Manufactured by BSH Hausgeräte GmbH under Trademark License of Siemens AG
*9000978245*
9000978245
941031
*
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising