Siemens | LF31IVP60 | Operating/installations instructions | Siemens iQ700 Cube Operating/installations instructions

Siemens iQ700 Cube Operating/installations instructions
Extractor hood
siemens-home.bsh-group.com/welcome
en ,QVWUXFWLRQVIRULQVWDOODWLRQDQGXVH
Register
your
product
online
en
Table of contents
INSTRUCTION MANUAL.......................................................... 2
INSTALLATION INSTRUCTIONS .......................................... 10
8 Intended use................................................................... 2
( Important safety information ........................................ 3
7 Environmental protection ............................................. 4
1 Operating the appliance................................................ 5
2 Cleaning and maintenance ........................................... 6
3 Trouble shooting ........................................................... 9
4 Customer service........................................................... 9
( Important safety information...................................... 11
K General information .................................................... 12
5 Installation ................................................................... 12
enI nst r uct i ons f or i nst al at i on and use
INSTRUCTION MANUAL
Produktinfo
Additional information on products, accessories,
replacement parts and services can be found at
www.siemens-home.bsh-group.com and in the online
shop www.siemens-home.bsh-group.com/eshops
8Intended use
Read these instructions carefully. Only then
will you be able to operate your appliance
safely and correctly. Retain the instruction
manual and installation instructions for future
use or for subsequent owners.
The appliance can only be used safely if it is
correctly installed according to the safety
instructions. The installer is responsible for
ensuring that the appliance works perfectly at
its installation location.
This appliance is intended for domestic use
and the household environment only. The
appliance is not intended for use outside. Do
not leave the appliance unattended during
operation. The manufacturer is not liable for
damage which is caused by improper use or
incorrect operation.
I nt ended us e
2
This appliance is intended for use up to a
maximum height of 2000 metres above sea
level.
This appliance may be used by children over
the age of 8 years old and by persons with
reduced physical, sensory or mental capacity
or by persons with a lack of experience or
knowledge if they are supervised by someone
who is responsible for their safety, or have
been instructed in how to use the appliance
safely and have understood the risks involved
in not using it properly.
Children must not play with the
appliance.Cleaning and user maintenance
must not be performed by children unless they
are over 15 years of age and are supervised.
Keep children below the age of 8 years old at
a safe distance from the appliance and power
cable.
Check the appliance for damage after
unpacking it. Do not connect the appliance if it
has been damaged in transport.
This appliance is not intended for operation
with an external clock timer or a remote
control.
Important safety information
(Important safety
information
:Warning
Danger of suffocation!
Packaging material is dangerous to children.
Never allow children to play with packaging
material.
I mpor t ant saf et y i nf or mat i on
: Warning
Risk of fire!
Fatty deposits in the grease filter may catch
fire. Regularly clean the grease filter. Never
operate the appliance without a grease
filter.
Risk
of fire!deposits in the grease filter may
■
Grease
catch fire. Never work with naked flames
close to the appliance (e.g. flambéing). Do
not install the appliance near a heatproducing appliance for solid fuel
(e.g. wood or coal) unless a closed, nonremovable cover is available. There must
be no flying sparks.
Risk
of oil
fire!
■
Hot
and fat can ignite very quickly. Never
leave hot fat or oil unattended. Never use
water to put out burning oil or fat. Switch off
the hotplate. Extinguish flames carefully
using a lid, fire blanket or something similar.
Risk
of fire!
■
When
gas burners are in operation without
any cookware placed on them, they can
build up a lot of heat. A ventilation
appliance installed above the cooker may
become damaged or catch fire. Only
operate the gas burners with cookware on
them.
Risk
of fire! several gas burners at the same
■
Operating
time gives rise to a great deal of heat. A
ventilation appliance installed above the
cooker may become damaged or catch fire.
Never operate two gas burners
simultaneously on the highest flame for
longer than 15 minutes. One large burner of
more than 5 kW (wok) is equivalent to the
power of two gas burners.
■
en
: Warning
Risk of burns!
The accessible parts become very hot when in
operation. Never touch hot parts. Keep
children at a safe distance.
: Warning
Risk of injury!
■
Components inside the appliance may have
sharp edges. Wear protective gloves.
Risk
of injury!
■
Items
placed on the appliance may fall
down. Do not place any objects on the
appliance.
Risk
of injury!
■
The
light emitted by LED lights is very
dazzling, and can damage the eyes (risk
group 1). Do not look directly into the
switched on LED lights for longer than
100 seconds.
: Warning
Risk of injury!
Items placed on the appliance may overload
the fasteners, potentially causing the
appliance to fall off the wall.Do not place items
on the appliance.
: Warning
Risk of electric shock!
■
A defective appliance may cause electric
shock. Never switch on a defective
appliance. Unplug the appliance from the
mains or switch off the circuit breaker in the
fuse box. Contact the after-sales service.
Risk
of electric
shock!are dangerous. Repairs
■
Incorrect
repairs
may only be carried out and damaged
power cables replaced by one of our
trained after-sales technicians. If the
appliance is defective, unplug the appliance
from the mains or switch off the circuit
breaker in the fuse box. Contact the aftersales service.
Risk
electric
■
Doofnot
use shock!
any high-pressure cleaners or
steam cleaners, which can result in an
electric shock.
3
en
Environmental protection
Causes of damage
Caution!
Risk of damage due to corrosion. Always
switch on the appliance while cooking to avoid
condensation. Condensate can produce
corrosion damage.
Always replace faulty bulbs to prevent the
remaining bulbs from overloading.
Risk of damage due to ingress of humidity into
the electronic circuitry. Never clean operator
controls with a wet cloth.
Surface damage due to incorrect cleaning.
Clean stainless steel surfaces in the direction
of the grain only. Do not use any stainless
steel cleaners for operator controls.
Surface damage due to strong or abrasive
cleaning agents. Never use strong and
abrasive cleaning agents.
Risk of damage as a result of incorrect
loading of design elements. Do not pull design
elements.Do not place objects on the design
elements or hang objects from them.
7Environmental protection
Your new appliance is particularly energy-efficient.
Here you can find tips on how to save even more
energy when using the appliance, and how to dispose
of your appliance properly.
Envi r onment al pr ot ect i on
Saving energy
■
■
■
■
■
■
During cooking, ensure that there is a sufficient
supply of air so that the extractor hood can work
efficiently and with a low level of operating noise.
Adjust the fan speed to the intensity of the cooking
fumes. Only use intensive mode where this is
required. A lower fan speed means that less energy
is consumed.
If there are intensive cooking fumes, select a higher
fan speed in good time. If cooking fumes have
already spread in the kitchen, the extractor hood
must be operated for longer.
Switch off the extractor hood if you no longer require
it.
Switch off the lighting if you no longer require it.
Clean and, if required, replace the filter at regular
intervals in order to increase the effectiveness of the
ventilation system and to prevent the risk of fire.
Environmentally-friendly disposal
Dispose of packaging in an environmentally-friendly
manner.
This appliance is labelled in accordance with
European Directive 2012/19/EU concerning
used electrical and electronic appliances
(waste electrical and electronic equipment WEEE). The guideline determines the
framework for the return and recycling of used
appliances as applicable throughout the EU.
4
Operating the appliance en
1Operating the appliance
These instructions apply to several appliance variants.
It is possible that individual features are described
which do not apply to your appliance.
Oper at i ng t he ap l i ance
Note: Switch on the extractor hood when you start
cooking and switch it off again several minutes after you
have finished cooking. This is the most effective way of
removing the kitchen fumes.
Control panel
Symbol
#
=
A
@
&
x
Explanation
Fan on/off
Light on/off/dimming
Intensive setting
You can use the intensive setting if there is a large
build-up of odours and fumes/vapours.
Decrease fan setting
Switching on
Increase fan setting/intensive mode 1, 2
Touch the @ symbol until 2 is shown on the display
panel.
Boost function (brief period at maximum power)
Fan run-on
Note: After approx. 6 minutes, the extractor hood
automatically switches back to fan setting 3.
Indicator/
symbol
Explanation
!
"
Metal grease filter saturation indicator
Activated charcoal filter saturation indicator
Switching off
If you want to end intensive mode before the preset
time expires, touch the A symbol to select the fan
setting you require.
1-3
Fan settings
Fan run-on
Boost function
Intensive mode
Switching on
x
2
Touch the & symbol.
Setting the fan
Switching on
■
■
Touch the # symbol.
The fan starts at setting ƒ.
Touch the + or - symbol to alter the fan speed.
Switching off
Touch the # symbol.
Note: After approximately 20 seconds, the extractor
hood automatically switches back to the fan setting that
was set beforehand.
Switching off
If you want to end the Boost function before the preset
time expires, touch the & symbol.
Fan run-on time
Lighting
Switching on
The lighting can be switched on and off independently
of the fan.
Touch the x symbol.
Touch the = symbol.
Setting the brightness
Press and hold the = symbol until the desired
brightness is reached.
The fan will run at fan setting 1.
After approximately 10 minutes, the fan will switch itself
off automatically.
Switching off
Touch the x symbol.
This immediately stops fan run-on.
5
en
Cleaning and maintenance
Saturation display
If the metal grease filters or activated charcoal filter are/
is saturated, the corresponding symbols will flash once
the appliance has been switched off:
■
■
■
Metal grease filter: !
Activated charcoal filter: "
Metal grease filter and activated charcoal filter: !
and "
If you have not yet done so, the metal grease filters
should now be cleaned or the activated charcoal filter
replaced. ~ "Cleaning and maintenance" on page 6
The saturation indicators can be reset while they are
flashing. To do this, touch the A symbol.
Switching over the display for air recirculation mode
For air recirculation mode, the electronic controller must
be switched over accordingly:
■
■
■
■
The extractor hood must be connected and switched
off.
Touch and hold the # and @ symbols at the same
time until "2" lights up for air recirculation mode
(filters that cannot be regenerated).
Repeatedly touching and holding this button
combination makes "3" light up for air recirculation
mode (filters that can be regenerated).
Repeatedly pressing and holding this button
combination switches the electronic controller back
over to air extraction mode ("1" ).
Audible signal
Switching on
Touch and hold the # and & symbols at the same time
for approximately 3 seconds when the fan is switched
off. An audible signal will sound as an
acknowledgement.
When the signal tone is activated, ‚ will be lit.
Switching off
Touch and hold the # and & symbols at the same time
for approximately 3 seconds when the fan is switched
off. An audible signal will sound as an
acknowledgement.
When the signal tone is deactivated, ‹ will be lit.
6
2Cleaning and maintenance
:Warning
Risk of injury!
Items placed on the appliance may overload the
fasteners, potentially causing the appliance to fall off the
wall.Do not place items on the appliance.
Cl eani ng and mai nt enance
: Warning
Risk of electric shock!
Penetrating moisture may result in an electric shock.
Clean the appliance using a damp cloth only. Before
cleaning, pull out the mains plug or switch off the circuit
breaker in the fuse box.
: Warning
Risk of electric shock!
Do not use any high-pressure cleaners or steam
cleaners, which can result in an electric shock.
: Warning
Risk of injury!
Components inside the appliance may have sharp
edges. Wear protective gloves.
: Warning
Risk of injury!
If appliances supported by cables are permitted to
swing to and fro, this may overload the fasteners,
potentially causing the appliance to fall off the wall.Do
not do anything that makes the appliance swing to and
fro.
Cleaning and maintenance
Cleaning agents
Removing metal grease filter
To ensure that the different surfaces are not damaged
by using the wrong cleaning product, follow the
instructions in the table. Do not use any of the following:
1. Open the lock and swing down the metal grease
■
■
■
■
■
■
■
Harsh or abrasive cleaning agents, e.g. scouring
powder or liquid scouring cleaner,
Cleaning products with a high alcohol content,
Hard scouring pads or cleaning sponges,
Pressure washers or steam cleaners,
Cleaning products that dissolve limescale,
Aggressive all-purpose cleaning products,
Oven spray.
en
filter. When you do this, take hold of the metal
grease filter from underneath with your other hand.
2. Take the metal grease filter out of the holder.
Note: Wash new sponge cloths thoroughly before use.
Note: Follow all instructions and warnings included with
the cleaning products.
Area
Stainless steel
Cleaning products
Hot soapy water:
Clean with a dish cloth and then dry with a
soft cloth.
Clean stainless steel surfaces in the direction
of the grain only.
Special stainless steel cleaning products are
available from our after-sales service or from
specialist retailers.Apply a very thin layer of
the cleaning product with a soft cloth.
Painted surfaces
Hot soapy water:
Clean using a damp dish cloth and then dry
with a soft cloth.
Do not use stainless steel cleaner.
Aluminium and plastic Hot soapy water:
Clean with a soft cloth.
Glass
Glass cleaner:
Clean with a soft cloth. Do not use a glass
scraper.
Controls
Hot soapy water:
Clean using a damp dish cloth and then dry
with a soft cloth.
Risk of electric shock caused by penetrating
moisture.
Risk of damage to the electronics caused by
penetrating moisture. Never clean controls
with a wet cloth.
Do not use stainless steel cleaner.
--------
Notes
– Fat may accumulate in the bottom of the metal
grease filter.
– Hold the metal grease filter level to prevent fat
from dripping out.
3. Clean the metal grease filter.
4. Clean the appliance support cables.
5. Clean the accessible parts of the housing. Clean the
inside of the appliance.
: Warning
Risk of injury!
Components inside the appliance may have sharp
edges. Wear protective gloves.
Cleaning the metal mesh grease filters
These instructions apply to several appliance variants. It
is possible that individual features are described which
do not apply to your appliance.
: Warning
Risk of fire!
Fatty deposits in the grease filter may catch fire.
Regularly clean the grease filter. Never operate the
appliance without a grease filter.
Notes
■
Do not use aggressive, acidic or alkaline cleaning
products.
■
We recommend cleaning the grease filters every 2
months.
■
When cleaning the metal grease filters, also clean
the metal grease filter holder in the appliance using
a damp cloth.
■
The metal grease filters can be cleaned in the
dishwasher or by hand.
7
en
Cleaning and maintenance
By hand:
Replacing the activated charcoal filter
Note: You can use a special degreaser to remove
stubborn dirt. This can be ordered from the online shop.
Note: To bind odours in circulating-air mode, you must
install an activated carbon filter. The different options for
operating the appliance in circulating-air mode can be
found in the brochure. Alternatively, ask your dealer.
The required accessories are available from specialist
retailers, from customer service or from the Online
Shop.
■
■
■
Soak the metal grease filters in hot soapy water.
Clean the filters with a brush and then rinse them
thoroughly.
Leave the metal grease filters to drain on an
absorbent material.
In the dishwasher:
Note: Slight discolouration may occur if the metal
grease filters are cleaned in the dishwasher. This
discolouration has no effect on the performance of the
metal grease filters.
■
■
■
■
1. Open the cover on the top of the appliance.
2. Remove the old activated charcoal filter and insert
the new one.
Use normal domestic dishwashing detergents.
Do not clean heavily soiled metal grease filters
together with cookware.
Place the metal grease filters in the dishwasher,
leaving plenty of space around them. Do not trap the
metal grease filters.
Select a temperature of no more than 50 °C.
Installing the metal mesh grease filter
: Warning
Risk of injury!
Components inside the appliance may have sharp
edges. Wear protective gloves.
Notes
■
Clean all accessible parts of the housing.
■
Clean the appliance support cables with care.
1. Insert the metal grease filter. When you do this, take
hold of the metal grease filter from underneath with
your other hand.
Note: Make sure that the metal grease filter is
positioned correctly.
2. Swing the metal grease filter up and click it into
place.
3. If the metal grease filter has not been inserted
correctly, open the lock and reinsert the metal
grease filter correctly.
8
3. Close the cover.
4. Reset the saturation indicator.~ "Saturation display"
on page 6
Trouble shooting
en
3Trouble shooting
4Customer service
Malfunctions often have simple explanations. Please
read the following notes before calling the after-sales
service.
When calling us, please quote the product number (E
no.) and the production number (FD no.) so that we can
provide you with the correct advice. These numbers can
be found on the rating plate on the top of the appliance
(to access it, you will need to remove the activated
charcoal filter).
Tr oubl e sho t i ng
: Warning
Risk of electric shock!
Incorrect repairs are dangerous. Repairs may only be
carried out and damaged power cables replaced by
one of our trained after-sales technicians. If the
appliance is defective, unplug the appliance from the
mains or switch off the circuit breaker in the fuse box.
Contact the after-sales service.
Malfunction table
Problem
The appliance
does not work
Possible cause
The plug is not
plugged in.
Power cut
Faulty fuse
The lighting does
not work.
The button illumination does not
work.
Solution
Connect the appliance to the
electricity supply
Check whether other kitchen
appliances are working
Check in the fuse box to make
sure that the fuse for the
appliance is OK
Call the after-sales service.
The LED lights
are defective.
The control unit is Call the after­sales service.
faulty.
--------
LED lights
Cust omer ser vi ce
E-Nr:
FD:
Z-Nr:
Type:
You can make a note of the numbers of your appliance
and the telephone number of the after-sales service in
the space below to save time should it be required.
E no.
FD no.
After-sales serviceO
Please be aware that a visit by an after-sales engineer
will be charged if a problem turns out to be the result of
operator error, even during the warranty period.
Please find the contact data of all countries in the
enclosed customer service list.
To book an engineer visit and product advice
GB
0344 892 8999
Calls charged at local or mobile rate.
IE
01450 2655
0.03 € per minute at peak. Off peak 0.0088 €
per minute.
Defective LED lights may be replaced by the
manufacturer, their customer service or a qualified
technician (electrician) only.
Rely on the professionalism of the manufacturer. You
can therefore be sure that the repair is carried out by
trained service technicians who carry original spare
parts for your appliances.
: Warning
Accessories
Risk of injury!
The light emitted by LED lights is very dazzling, and can
damage the eyes (risk group 1). Do not look directly
into the switched on LED lights for longer than
100 seconds.
(not included in the scope of delivery)
Note: These instructions apply to several appliance
models. It may be the case that an optional accessory
that is listed does not apply for your appliance.
Note: Observe the installation instructions in the
accessory.
Easy-change filter for CleanAir air recirculation
module (cannot be regenerated)
Easy-change filter for CleanAir air-recirculation
module (can be regenerated)
LZ56200
LZ00XXP00
--------
9
Installation instructions
en
INSTALLATION INSTRUCTIONS
I nst al at i on i nst r uct i onsInstallation instructions
[
[
[
[
[
[
! PP
! PP
■
■
10
This appliance is fitted to the kitchen ceiling or a
sturdy suspended ceiling.
The surfaces of the appliance are sensitive. Avoid
damaging them during installation.
Important safety information
(Important safety
information
Read these instructions carefully. Only then
will you be able to operate your appliance
safely and correctly. Retain the instruction
manual and installation instructions for future
use or for subsequent owners.
Check the appliance for damage after
unpacking it. Do not connect the appliance if it
has been damaged in transport.
The appliance can only be used safely if it is
correctly installed according to the safety
instructions. The installer is responsible for
ensuring that the appliance works perfectly at
its installation location.
Only a licensed professional may connect
appliances without plugs. Damage caused by
incorrect connection is not covered under
warranty.
The surfaces of the appliance are easily
damaged. Avoid damaging them during
installation.
For the installation, observe the currently valid
building regulations and the regulations of the
local electricity and gas suppliers.
I mpor t ant saf et y i nf or mat i on
: Warning
Risk of fire!
Fatty deposits in the grease filter may catch
fire. The specified safety clearances must
be complied with in order to prevent a buildup of heat. Refer to the information
provided for your cooker. If gas and electric
hobs are being operated together, the
largest specified clearance applies.
Risk
of fire!deposits in the grease filter may
■
Grease
catch fire. Never work with naked flames
close to the appliance (e.g. flambéing). Do
not install the appliance near a heatproducing appliance for solid fuel
(e.g. wood or coal) unless a closed, nonremovable cover is available. There must
be no flying sparks.
■
en
: Warning
Risk of injury!
■
Components inside the appliance may have
sharp edges. Wear protective gloves.
Risk
of injury!
■
The
appliance may fall down if it has not
been properly fastened in place. All
fastening components must be fixed firmly
and securely.
Risk
of injury!
■
The
appliance is heavy. To move the
appliance, 2 people are required. Use only
suitable tools and equipment.
Risk
of injury!to the electrical or mechanical
■
Changes
assembly are dangerous and may lead to
malfunctions. Do not make any changes to
the electrical or mechanical assembly.
Risk
of injury!
■
Risk
of falling when working on the
appliance. Use a stable stepladder.
: Warning
Risk of electric shock!
Components inside the appliance may have
sharp edges. These may damage the
connecting cable. Do not kink or pinch the
connecting cable during installation.
: Warning
Risk of electric shock!
It must always be possible to disconnect the
appliance from the power supply. If there is a
fixed connection, an all-pole isolating switch
with a contact gap of at least 3 mm must be
provided for the wiring. Only an electrician
may install the fixed connection.We
recommend installing a residual-current circuit
breaker (RCCB) in the appliance's power
supply circuit.
: Warning
Risk of electric shock!
Incorrect repairs are dangerous. Repairs may
only be carried out and damaged power
cables replaced by one of our trained aftersales technicians. If the appliance is defective,
unplug the appliance from the mains or switch
off the circuit breaker in the fuse box. Contact
the after-sales service.
: Warning
Danger of suffocation!
Packaging material is dangerous to children.
Never allow children to play with packaging
material.
11
en
General information
KGeneral information
Gener al i nf or mat i on
Preparing the ceiling
■
■
■
■
The ceiling must be flat, horizontal and have
adequate load-bearing capacity.
The depth of the bore holes must be the same
length as the screws. The wall plugs must have a
secure grip.
The enclosed screws and wall plugs are suitable for
solid brickwork. Suitable fasteners must be used for
other structures (e.g. plasterboard, porous concrete,
poroton bricks).
The maximum weight of the extractor hood is 26 kg.
Electrical connection
: Warning
Risk of electric shock!
It must always be possible to disconnect the appliance
from the power supply. If there is a fixed connection, an
all-pole isolating switch with a contact gap of at least
3 mm must be provided for the wiring. Only an
electrician may install the fixed connection.We
recommend installing a residual-current circuit breaker
(RCCB) in the appliance's power supply circuit.
5Installation
I ns t a l a t i o n
Preparing for installation
Caution!
Ensure that there are no electrical wires, gas pipes or
water pipes in the area where holes are to be drilled.
1. Cover the hob to protect it from damage.
2. Mark where the centre of the extractor hood should
be on the ceiling above the centre of the hob.
3. Using the template provided, mark the locations
where the bolts should be inserted on the ceiling.
4. Drill four 8 mm diameter holes to a depth of 80 mm
for fastening the appliance and press in the wall
plugs flush with the wall.
Preparing the appliance
1. Screw in the four bolts on the edge of the frame at
the marked locations, leaving them protruding out of
the frame by approx. 5 mm.
: Warning
Risk of electric shock!
Components inside the appliance may have sharp
edges. These may damage the connecting cable. Do
not kink or pinch the connecting cable during
installation.
The required connection information can be found on
the rating plate inside the appliance; to access it, you
will need to remove the activated charcoal filter.
Length of the cable: approx. 1.30 m
This appliance complies with the EC interference
suppression regulations.
The appliance must be disconnected from the power
supply whenever installation work is being carried out.
When the appliance is installed, protection must be
provided against accidental contact in the future.
12
min. 5 mm
2. Remove the film from the frame cover.
3. Remove the activated charcoal filter from the film.
4. Open the cover on the top of the appliance and
remove it ¨, insert the activated charcoal filter ©
and then close the cover.
Installation
en
2. Insert the two bolts on the ceiling through the
Fitting the frame
1. Screw in the two bolts, leaving them protruding out
of the ceiling by 5 - 9 mm ¨.
Note: Make sure that the bolts ¨, frame ©, frame
cover ª and control « are positioned correctly
relative to one another. The position of the control is
marked on the template.
openings provided in the frame ¨. Move the frame
to allow the bolts to be screwed into the keyhole
openings ©.
PP
PP
3. Use two more bolts to screw the frame in place.
ª
Tighten all the bolts fully.
4. Insert the four cables into the openings provided in
the frame and thread them through the labyrinth.
13
en
Installation
Establishing a connection to the mains
Fitting the frame cover
: Warning
1. Slide the frame cover up.
Risk of electric shock!
It must always be possible to disconnect the appliance
from the power supply. If there is a fixed connection, an
all-pole isolating switch with a contact gap of at least
3 mm must be provided for the wiring. Only an
electrician may install the fixed connection.We
recommend installing a residual-current circuit breaker
(RCCB) in the appliance's power supply circuit.
Note: Thread the mains power cable through the
opening in the frame cover and, if necessary,
carefully pull it down.
3(
1
/
Note: To find out the correct fuse rating, see the total
connected load (in watts) on the appliance's rating
plate.
1. Position the appliance underneath the frame.
2. Carefully thread the cables and the mains power
cable through the opening in the frame cover. Place
the frame cover down onto the appliance.
3. Mount the appliance on the wall and level it; see the
section entitled "Wall-mounting the appliance and
levelling it".
4. Thread the mains power cable through the opening
in the frame and then through the strain relief.
Caution!
Do not position the mains power cable that is inside
the frame underneath the frame.
2. Fit the frame cover onto the four bolts at the edge of
the frame.
Note: Slide the frame cover approx. 5 mm to the
right until you hear it click into place.
3(
1
/
3. Tighten the bolts at the edge of the frame.
4. Secure the covers to the magnets to hide the bolts
at the edges of the frame.
5. Connect the appliance to the power supply.
Caution!
Pay attention to the marks on the connection
terminals when connecting the wires (permissible
cross sections of the domestic wiring: 1 mm² 2.5 mm²) in the mains power cable.
6. Use an open-ended spanner (WAF 17) to tighten the
strain relief until the mains power cable is held firmly
and cannot move.
14
Installation
Attaching and aligning the appliance
1. Manually open the cable tensioners until the cable
can be inserted in it. Do not use any tools.
Note: Do not open the cable tensioners fully. The
cable tensioners may fall into the appliance.
2. Enlist the help of a second person to lift the
appliance and thread the cables into the cable
tensioners on the top of the appliance.
Note: Never shorten the cables.
en
4. If you need to position the appliance lower down, lift
it up ¨, push the cable tensioners down © and pull
the cables back out of the cable tensioners ª.
5. After aligning, tighten the cable tensioners so that
they are hand-tight. Do not use any tools.
3. Taking care to comply with the safety clearances,
slide the appliance up and level it.
15
BSH Hausgeräte GmbH
Carl-Wery-Straße 34, 81739 München
GERMANY
siemens-home.bsh-group.com
0DQXIDFWXUHGE\%6++DXVJHUlWH*PE+XQGHU7UDGHPDUN/LFHQVHRI6LHPHQV$*
*9001194887*
9001194887
971101
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising