Siemens | LR18HLT25 | Installation Instruction | Siemens iQ700 Ceiling cooker hood White Installation Instruction

Siemens iQ700 Ceiling cooker hood White Installation Instruction
Ceiling ventilation
[en]
Instructions for installation and use
en
Table of contents
[en] I nst r uct i ons f or i nst al at i on and use Cei l i ng vent i l at i on
INSTRUCTION MANUAL ..........................................................3
8 Intended use ......................................................... 3
( Important safety information .............................. 4
7 Environmental protection.................................... 6
Ç Operating mode.................................................... 6
1 Operating the appliance ...................................... 7
e Connecting to a hob .......................................... 10
o Home Connect.................................................... 11
2 Cleaning and maintenance................................ 13
3 Trouble shooting................................................ 16
4 Customer service ............................................... 16
INSTALLATION INSTRUCTIONS...........................................17
( Important safety information ............................ 18
K General information ........................................... 19
5 Installation .......................................................... 19
INSTRUCTION MANUAL
Produktinfo
Additional information on products, accessories,
replacement parts and services can be found at
www.siemens-home.bsh-group.com and in the online
shop www.siemens-home.bsh-group.com/eshops
8Intended use
Read these instructions carefully. Only then
will you be able to operate your appliance
safely and correctly. Retain the instruction
manual and installation instructions for future
use or for subsequent owners.
The appliance can only be used safely if it is
correctly installed according to the safety
instructions. The installer is responsible for
ensuring that the appliance works perfectly at
its installation location.
This appliance is intended for domestic use
and the household environment only. The
appliance is not intended for use outside. Do
not leave the appliance unattended during
operation. The manufacturer is not liable for
damage which is caused by improper use or
incorrect operation.
This appliance is intended for use up to a
maximum height of 2000 metres above sea
level.
I nt ended us e
This appliance may be used by children over
the age of 8 years old and by persons with
reduced physical, sensory or mental capacity
or by persons with a lack of experience or
knowledge if they are supervised by someone
who is responsible for their safety, or have
been instructed in how to use the appliance
safely and have understood the risks involved
in not using it properly.
Children must not play with the
appliance.Cleaning and user maintenance
must not be performed by children unless they
are over 15 years of age and are supervised.
Keep children below the age of 8 years old at
a safe distance from the appliance and power
cable.
Check the appliance for damage after
unpacking it. Do not connect the appliance if it
has been damaged in transport.
This appliance is not intended for operation
with an external clock timer or a remote
control.
3
en
Important safety information
(Important safety
information
:Warning – Danger of suffocation!
Packaging material is dangerous to children.
Never allow children to play with packaging
material.
I mpor t ant saf et y i nf or mat i on
: Warning – Risk of fire!
Fatty deposits in the grease filter may catch
fire. Regularly clean the grease filter. Never
operate the appliance without a grease
filter.
Risk
of fire!deposits in the grease filter may
■
Grease
catch fire. Never work with naked flames
close to the appliance (e.g. flambéing). Do
not install the appliance near a heatproducing appliance for solid fuel (e.g.
wood or coal) unless a closed, nonremovable cover is available. There must
be no flying sparks.
Risk
of oil
fire!
■
Hot
and fat can ignite very quickly. Never
leave hot fat or oil unattended. Never use
water to put out burning oil or fat. Switch off
the hotplate. Extinguish flames carefully
using a lid, fire blanket or something similar.
Risk
of fire!
■
When
gas burners are in operation without
any cookware placed on them, they can
build up a lot of heat. A ventilation
appliance installed above the cooker may
become damaged or catch fire. Only
operate the gas burners with cookware on
them.
Risk
of fire! several gas burners at the same
■
Operating
time gives rise to a great deal of heat. A
ventilation appliance installed above the
cooker may become damaged or catch fire.
Never operate two gas burners
simultaneously on the highest flame for
longer than 15 minutes. One large burner of
more than 5 kW (wok) is equivalent to the
power of two gas burners.
■
: Warning – Risk of burns!
The accessible parts become very hot when in
operation. Never touch hot parts. Keep
children at a safe distance.
4
: Warning – Risk of injury!
Components inside the appliance may have
sharp edges. Wear protective gloves.
Risk
of injury!
■
The
appliance may fall down if it has not
been properly fastened in place. All
fastening components must be fixed firmly
and securely.
Risk
of injury!
■
The
appliance is heavy. To move the
appliance, 2 people are required. Use only
suitable tools and equipment.
Risk
of injury!
■
The
appliance is very heavy. The appliance
must not be fitted directly onto plasterboard
or similar lightweight materials. To ensure
correct installation, you must use a material
which is sufficiently stable and suitable for
both the structural conditions and the
weight of the appliance.
Risk
of injury!to the electrical or mechanical
■
Changes
assembly are dangerous and may lead to
malfunctions. Do not make any changes to
the electrical or mechanical assembly.
Risk
of filter
injury!
■
The
cover may swing out. Always open
and close the filter cover slowly. Ensure that
the filter cover does not swing out after it is
released.
Risk
of injury!
■
Risk
of trapping body parts when opening
and closing the filter cover. Do not reach
into the area behind the filter cover and
keep your hands away from the hinges.
Risk
of injury!can be easily swallowed by
■
Batteries
children. Keep batteries out of the reach of
children. Do not allow children to change
batteries without supervision.
Risk
of injury!may explode. Do not charge or
■
Batteries
short-circuit the batteries. Do not throw
batteries into a fire.
Risk
of injury!
■
The
connection terminals must not be short
circuited.
Risk
of injury!
■
Only
batteries of the specified type may be
used. Different types of batteries or old and
new batteries must not be mixed together.
Risk
of injury!
■
Rechargeable
batteries must not be used.
Risk
of injury!
■
Items
placed on the appliance may fall
down. Do not place any objects on the
appliance.
Risk
of injury! movement of the appliance may
■
Oscillating
result in injury. Do not do anything that
makes the appliance swing to and fro.
When moving the appliance up and down,
leave sufficient distance to the appliance.
Risk
of injury! supported by cables are
■
If appliances
permitted to swing to and fro, this may
overload the fasteners, potentially causing
the appliance to fall off the wall.Do not do
anything that makes the appliance swing to
and fro.
■
Important safety information
Risk
Items
of injury!
placed on the appliance may
overload the fasteners, potentially causing
the appliance to fall off the wall.Do not
place items on the appliance.
Risk
of injury!
■
Objects
left on the hob may tip over when
the filter cover is opened. This can cause
burns. Clear the hob before opening the
filter cover.
Risk
injury!
■
In of
the
case of damaged cables or unusual
noises during the upward or downward
movement, the appliance must no longer be
used.
Risk
of injury!
■
Before
cleaning the appliance, disconnect it
from the Home Connect app to ensure that
operation via the Home Connect app is not
possible.
■
: Warning – Risk of electric shock!
A defective appliance may cause electric
shock. Never switch on a defective
appliance. Unplug the appliance from the
mains or switch off the circuit breaker in the
fuse box. Contact the after-sales service.
Risk
of electric
shock!are dangerous. Repairs
■
Incorrect
repairs
may only be carried out and damaged
power cables replaced by one of our
trained after-sales technicians. If the
appliance is defective, unplug the appliance
from the mains or switch off the circuit
breaker in the fuse box. Contact the aftersales service.
Risk
of electric shock!
■
Penetrating
moisture may result in an
electric shock. Clean the appliance using a
damp cloth only. Before cleaning, pull out
the mains plug or switch off the circuit
breaker in the fuse box.
Risk
electric
■
Doofnot
use shock!
any high-pressure cleaners or
steam cleaners, which can result in an
electric shock.
Risk
of electric
■
If cables
areshock!
damaged or there is a spring
fracture in the cable spool unit, the
appliance must no longer be used.
■
en
Causes of damage
Caution!
Risk of damage due to corrosion. Always
switch on the appliance while cooking to avoid
condensation. Condensate can produce
corrosion damage.
Always replace faulty bulbs to prevent the
remaining bulbs from overloading.
Risk of damage due to ingress of humidity into
the electronic circuitry. Never clean operator
controls with a wet cloth.
Surface damage due to incorrect cleaning.
Clean stainless steel surfaces in the direction
of the grain only. Do not use any stainless
steel cleaners for operator controls.
Surface damage due to strong or abrasive
cleaning agents. Never use strong and
abrasive cleaning agents.
Risk of damage as a result of incorrect
loading of design elements. Do not pull design
elements.Do not place objects on the design
elements or hang objects from them.
Caution!
Damage to the remote control caused by
leaking batteries. Remove the batteries in the
remote control if the remote control is not
being used over a longer period of time.
Caution!
Remove batteries that are flat or defective
from the remote control and dispose of them
safely in accordance with local regulations. Do
not dispose of batteries alongside general
household waste.
Items placed on the appliance may damage
the appliance or adjacent cooktops when the
appliance is extended or retracted. Do not
place any objects on the moving parts of the
appliance.
Caution!
There is a risk of surface damage if you do not
peel off the protective film.Remove the
protective film from all parts of the appliance
before using the appliance for the first time.
5
en
Environmental protection
7Environmental protection
Your new appliance is particularly energy-efficient.
Here you can find tips on how to save even more
energy when using the appliance, and how to dispose
of your appliance properly.
Envi r onment al pr ot ect i on
Saving energy
■
■
■
■
■
■
Adjust the fan speed to the amount of cooking
vapour produced during cooking. Only use intensive
mode when required. The lower the fan speed, the
less energy is consumed.
If cooking produces large amounts of vapour, select
a higher fan speed in good time. If the cooking
vapours have already spread around the kitchen, the
appliance will need to be operated for longer.
Switch the appliance off when you are not using it.
Switch the lighting off when are you are not using it.
Clean and (if required) replace the filter at regular
intervals in order to increase the effectiveness of the
ventilation system and to prevent the risk of fire.
Put the lid on to reduce cooking vapours and
condensation.
Environmentally-friendly disposal
Dispose of packaging in an environmentally-friendly
manner.
This appliance is labelled in accordance with
European Directive 2012/19/EU concerning
used electrical and electronic appliances
(waste electrical and electronic equipment WEEE). The guideline determines the
framework for the return and recycling of used
appliances as applicable throughout the EU.
Disposing of batteries
Dispose of used batteries in an environmentally friendly
manner.
Batteries must not be disposed of in the
household waste after use. Consumers are
obliged by law to return all used batteries to a
retailer or other collection points.
The retailer is obliged to take back used
batteries free of charge.
6
ÇOperating mode
This appliance is intended for use in circulating-air
mode.
Oper at i ng mode
Circulating-air mode
The air which is drawn in is cleaned by the
grease filters and an odour filter, and
conveyed back into the kitchen.
Note: To bind odours in circulating-air mode, you must
install an odour filter. The different options for operating
the appliance in circulating-air mode can be found in
our catalogue. Alternatively, ask your specialist retailer.
The required accessories are available from specialist
retailers, from our after-sales service or from the online
shop.
Operating the appliance
1Operating the appliance
These instructions apply to several appliance variants.
It is possible that individual features are described
which do not apply to your appliance.
If your appliance has Home Connect, more functions
are only available in the Home Connect app.
en
LED display
Oper at i ng t he ap l i ance
Note: Switch on the extractor hood when you start
cooking and switch it off again several minutes after you
have finished cooking. This is the most effective way of
removing the kitchen fumes.
Remote control
Use the remote control to set and adjust the various
different functions of your appliance.
Note: Align the remote control as precisely as possible
to the infrared receiver for the LED display on the
appliance.
LED
1
2
3
4
5
6
7
8
Explanation
Fan setting 1
Fan setting 2
Fan setting 3
Intensive mode 1
Intensive mode 2
Automatic mode / fan run-on time / interval ventilation
Home Connect
Infrared receiver
Lift-up functions
You can move the appliance downwards, upwards or to
a defined position using the † and … buttons.
Moving the appliance down
Press the † button.
The appliance moves downwards.
Notes
■
If you briefly press the † button, the appliance
moves downwards as far as the last saved position.
■
If you press the † button for approx. one second,
the appliance moves fully downwards.
Symbol
#
B
…
†
@
A
w
„
D
y
Explanation
Switch the appliance on/off, switch the fan on/off
Switch the light on/off, adjust the brightness
Start up the appliance
Shut down the appliance
Increase the fan setting
Decrease the fan setting
Switch on automatic mode
Switch on the boost function
Connect Home Connect
Reset the filter saturation
Moving the appliance up
Press the … button.
The appliance moves upwards.
Notes
■
If you briefly press the … button, the appliance
moves upwards as far as the last saved position.
■
If you press the … button for approx. one second,
the appliance moves fully upwards.
Setting the fan
Switching on
1. Press the # button.
The appliance moves to the most recently stored
position, the fan starts at fan setting 2.
2. Press the @ or A button to set a different fan setting.
The corresponding LEDs light up on the appliance.
Switching off
Press the # button.
The fan run-on is activated, LED 6 on the appliance
flashes and the appliance moves into the run-on
position. After approx. 10 minutes, the fan switches off
automatically, the appliance moves up as far as it will
go.
7
en
Operating the appliance
Intensive setting
Automatic mode
You can use the intensive setting if there is a large
build-up of odours and fumes/vapours.
Switching on
Switching on
1. Press the # button.
The appliance moves to the most recently stored
position, the fan starts in fan setting 2. LED 2 lights
up on the appliance.
2. Press the @ button twice in order to set intensive
mode 1.
3. Press the @ button again in order to set intensive
mode 2.
The corresponding LEDs light up on the appliance.
Note: After approx. 6 minutes, the appliance
automatically switches back to fan setting 3.
Fan run-on time
Switching on
Note: The fan run-on is used to dry the odour filter when
you have finished cooking.
1. Press the # button.
The appliance moves to the most recently stored
position, the fan starts in fan setting 2. LED 2 lights
up on the appliance.
2. Press the A button twice.
LED 1 and LED 6 flash on the appliance. After
approx. 10 minutes, the fan switches off
automatically and the appliance moves up as far as
it will go.
Switching off
To end the fan run-on early, press the # button.
This immediately stops the fan run-on. The appliance
moves up as far as it will go.
1. Press the # button.
The appliance moves to the last-saved position, the
fan starts at fan setting 2. Led 2 lights up on the
appliance.
2. Press the w button.
LED 6 on the appliance lights up and the optimum
fan setting is set automatically via a sensor.
Switching off
End automatic mode using the w button.
The appliance switches to the fan setting that was
previously set.
The fan switches itself off automatically if the sensor
detects no further change in the air quality of the room.
Automatic mode can run for a maximum of four hours.
If automatic mode is ended using the # button, the
appliance moves to the run-on position. The fan
switches off automatically after approx. 10 minutes, the
appliance moves fully upwards.
Sensor control
In automatic mode, a sensor in the appliance detects
the intensity of the cooking and roasting fumes.
Depending on the sensor setting, the fan automatically
switches itself to another fan setting.
Possible sensor settings:
Default sensitivity setting: LED 3
Lowest sensitivity setting: LED 1
Highest sensitivity setting: LED 5
If the sensor control responds too strongly or not
enough, it can be changed accordingly:
1. When the appliance is switched off, press and hold
the # and w buttons for approx. 3 seconds.
Intermittent ventilation
2. Press the @ or A button to change the sensor control
This function is only available in the Home Connect app.
With interval ventilation, the ventilation system switches
on and off in the selected setting for the selected time.
LED 6 flashes continuously, the LED for the selected
ventilation setting lights up on the appliance.
As soon as the ventilation duration comes to an end,
the LED for the ventilation setting you have selected
goes out. LED 6 continues to flash.
3. Press and hold the # and w buttons for approx.
8
setting.
3 seconds to save the setting or wait for around
10 seconds until the setting is saved automatically.
A signal tone will sound.
Note: Press the # button to cancel the setting.
Operating the appliance
en
Boost function
Lighting
Switching on
Press the „ button.
The lighting can be switched on and off independently
of the fan.
Press the B button.
Setting the brightness
Press and hold the B button for approx. 1 second until
the required brightness is reached.
Note: After approx. 20 seconds, the fan automatically
switches back to the fan setting that was set
beforehand.
Switching off
Press the „ button to end the boost function before the
preset time expires.
Note: Colour temperature settings are available in the
Home Connect app provided the appliance has this
function.
Saturation display
Button tone
If the grease filter or odour filter is saturated, the
corresponding LEDs will flash and a repeated signal
tone will sound after the appliance has been switched
off:
■
■
■
Grease filter: LED 1 flashes
Odour filter: LED 2 flashes
Grease filter and odour filter: LEDs 1 and 2 flash
The grease filters should now be cleaned or the odour
filter needs to be replaced. ~ "Cleaning and
maintenance" on page 13
The saturation indicators can be reset while they are
flashing. To do this, press the y button.
Settings for using the odour filter
1. When the appliance is switched off, press and hold
2.
3.
4.
5.
the # and y buttons for approx. 3 seconds.
The LED for the currently active filter setting lights up
on the appliance.
Press the @ button/A button until LED 2 for
circulating-air mode (filter cannot be regenerated)
lights up on the appliance.
Press the @ button/ A button until LED 3 for
circulating-air mode (filter can be regenerated) lights
up on the appliance.
Press the @ button/A button until LED 1 on the
appliance for the electronic controller is switched
back to operation without the air recirculation filter.
Press and hold the # and y buttons for approx.
3 seconds to save the setting or wait for around
10 seconds until the setting is saved automatically.
A signal tone will sound.
Switching on or off
Note: Only button tones can be switched on and off.
Signal tones on the appliance cannot be switched off.
1. When the appliance is switched off, press and hold
the # and A buttons for approx. 3 seconds.
The LED in the currently selected setting lights up.
2. Press the @ or A button to change the setting.
The button tones are switched on if LED 1 lights up
on the appliance.
The button tones are switched off if LED 2 lights up
on the appliance.
3. Press and hold the # and A buttons for approx.
3 seconds to save the setting or wait for around
10 seconds until the setting is saved automatically.
A signal tone will sound.
Note: Press the # button to cancel the setting.
Note: Press the # button to cancel the setting.
9
en
Connecting to a hob
eConnecting to a hob
You can connect this appliance to a hob (if the hob
supports connection to the appliance) and then control
the functions of the hood via your hob.
There are various options for connecting the appliances
together:
Home Connect
Two appliances can be connected using the Home
Connect app provided that both of them are Home
Connect-compatible.
Refer to the Home Connect documents supplied for
more information.
Con ect i ng t o a hob
Connecting appliances via your home network
If the appliances are connected to each other via your
home network, both the hood controls on the hob and
Home Connect can be used to operate the appliance.
Notes
Make sure you follow the safety instructions in the
instruction manual for your extractor hood and that
these are complied with even when operating the
appliance via the hood controls on the hob.
■
If the appliance is being operated by means of the
controls on the extractor hood, this mode of
operation always has priority. It is not possible to use
the hood controls on the hob during this time.
■
Setting up a connection
The hood must be switched off before you can connect
the hob and extractor hood.
Connecting directly
Make sure that the hob is switched on and is in search
mode.
To do this, refer to the section entitled "Connecting to
the extractor hood" in the instruction manual for your
hob.
Connecting appliances directly
If the appliance is connected directly to a hob, it cannot
be connected to your home network as well. The
appliance works like an extractor hood that is not
connected to the network and you can continue to
operate it via the control panel.
10
Notes
■
Before connecting the appliances, reset all existing
connections to your home network or other
appliances.
■
If your extractor hood is connected directly to the
hob, it cannot be connected to your home network
as well and you will not be able to use Home
Connect.
Press and hold the D button until the Home Connect
LED starts flashing.
The extractor hood has been connected to the hob
when the Home Connect LED stops flashing and
remains continuously lit.
Connecting via your home network
Follow the instructions in the section entitled "Automatic
login to your home network" or "Manually logging into
your home network" ~ "Home Connect" on page 11
Once the extractor hood is connected to your home
network, you can connect to the hob via the Home
Connect app. To do this. follow the instructions on your
mobile device.
Home Connect
oHome Connect
This appliance can be networked and also controlled
using a mobile device.
If the appliance is not connected to your home network,
it will function as an extractor hood with no network
connection and can still be operated via the display.
The availability of the Home Connect function depends
on the availability of Home Connect services in your
country. Home Connect services are not available in
every country. You can find more information on this at
www.home-connect.com.
Home Con ect
Notes
■
Ensure that you follow the safety instructions in this
instruction manual and that you comply with these
even when you are away from home and are
operating the appliance via the Home Connect app.
You must also follow the instructions in the Home
Connect app.
■
Operating the appliance directly from the appliance
always takes priority. It is not possible to operate the
appliance using the Home Connect app during this
time.
Setting up
To implement settings via Home Connect, you must
have installed and set up the Home Connect app on
your mobile device.
Refer to the Home Connect documents supplied for
more information.
The app will guide you through the entire registration
process. Follow the steps specified by the app to
implement the settings.
The app must be open in order to perform the set-up
process.
en
3. Press the WPS button on the router within the next
2 minutes.
Once the connection has been established, the
extractor hood will connect to the Home Connect
app automatically. LED 3 and LED 7 will flash.
Note: If the extractor hood has been unable to
connect, it will automatically allow you to manually
connect to your home network. The LED for fan
setting 2 and the Home Connect LED will flash. Log
the appliance into your home network manually or
press the A button to try logging in automatically
again.
4. On your mobile device, follow the instructions for
automatic network login.
The login process is complete when LED 7 on the
appliance stops flashing and remains continuously lit.
Manual registration in the home network
Notes
■
The extractor hood cannot be switched on during the
connection process. You can cancel the process at
any time by pressing the # symbol.
■
To connect the extractor hood to your home
network, the hood and the light must be switched off.
1. Press and hold the D button until LED 7 on the
appliance flashes.
2. Press the @ button twice to start logging into your
home network manually.
LED 2 and LED 7 will flash.
3. Follow the instructions in the app.
Notes
■
In networked standby mode, your appliance requires
a maximum of 2 W.
■
If you need your device's MAC address to connect to
your home network, you can find this next to the
rating plate inside the appliance (you will need to
remove the filter to see it).
Automatic registration in the home network
Notes
■
You need a router that has WPS functionality.
■
You need to be able to access your router. If this is
not the case, follow the steps for "Manually logging
into your home network".
■
The extractor hood cannot be switched on during the
connection process. You can cancel the process at
any time by pressing the # symbol.
■
To connect the extractor hood to your home
network, the hood and the light must be switched off.
Once the connection has been established, the
extractor hood will connect to the Home Connect
app automatically. LED 3 and LED 7 will flash.
4. On your mobile device, follow the instructions for
manually logging into your network.
The login process is complete when LED 7 on the
appliance stops flashing and remains continuously lit.
1. Press and hold the D button until LED 7 on the
appliance flashes.
2. Press the @ button.
LED 1 and LED 7 will flash.
11
en
Home Connect
Connecting to the app
If the Home Connect app is installed on your mobile
device, you can connect it to your extractor hood.
Notes
■
The appliance must be connected to the network.
■
The app must be open.
1. Press and hold the D button until LED 3 and LED
7 start flashing.
2. On your mobile device, follow the instructions in the
Home Connect app.
The connection process is complete when LED 7 on
the appliance stops flashing and remains continuously
lit.
Software update
Using the software update function, your extractor
hood's software can be updated (e.g. for the purpose of
optimisation, troubleshooting or security updates). To
do this, you need to be a registered Home Connect
user, have installed the app on your mobile device and
be connected to the Home Connect server.
As soon as a software update is available, you will be
informed through the Home Connect app and will be
able to start the software update via the app.
Once the update has been successfully downloaded,
you can start installing it via the Home Connect app if
you are on your local area network.
The Home Connect app will inform you once installation
is complete.
Notes
■
You can continue to use your extractor hood as
normal while updates are downloading.
■
Depending on your personal settings in the app,
software updates can also be set to download
automatically.
■
We recommend that you install security updates as
soon as possible.
Resetting the connection
You can reset the connections you have saved on your
home network and on Home Connect at any time.
Press and hold the w and @ buttons until LED 7 on the
appliance goes out. An audible signal will sound.
About data protection
When your appliance is connected for the first time to a
WLAN network, which is connected to the Internet, your
appliance transmits the following categories of data to
the Home Connect server (initial registration):
■
■
■
■
Unique appliance identification (consisting of
appliance codes as well as the MAC address of the
installed WiFi communication module).
Security certificate of the WiFi communication
module (to ensure a secure IT connection).
The current software and hardware version of your
domestic appliance.
Status of any previous resetting to factory settings.
This initial registration prepares the Home Connect
functions for use and is only required when you want to
use these Home Connect functions for the first time.
Note: Ensure that the Home Connect functions can be
used only in conjunction with the Home Connect app.
Information on data protection can be accessed in the
Home Connect app.
Declaration of Conformity
BSH Hausgeräte GmbH hereby declares that the
appliance which features Home Connect is in
accordance with the basic requirements and the other
relevant provisions of the directive 2014/53/EU.
A detailed RED Declaration of Conformity can be found
online at www.siemens-home.bsh-group.com on the
product page of your appliance with the additional
documents.
Remote diagnostics
If a fault occurs, the after-sales service can use remote
diagnostics to access your appliance.
Contact the after-sales service, making sure that your
appliance is connected to the Home Connect server
and checking that the remote diagnostics service is
available in your country.
Note: For more information and to check whether the
remote diagnostics service is available in your country,
please visit the Help & Support area of the Home
Connect website for your country: www.homeconnect.com
12
2.4 GHz band: max. 100 mW
5 GHz band: max. 100 mW
BE
BG
CZ
ES
FR
HR
HU
MT
NL
SK
FI
SE
5 GHz Wi-Fi: for indoor use only
y
DK
IT
AT
UK
DE
CY
PL
NO
EE
LV
PT
CH
IE
LT
RO
TR
EL
LU
SI
Cleaning and maintenance
2Cleaning and maintenance
Cl eani ng and mai nt enance
:Warning
Risk of electric shock!
■
Penetrating moisture may result in an electric shock.
Clean the appliance using a damp cloth only. Before
cleaning, pull out the mains plug or switch off the
circuit breaker in the fuse box.
■
Do not use any high-pressure cleaners or steam
cleaners, which can result in an electric shock.
Risk of electric shock!
: Warning
Risk of injury!
Oscillating movement of the appliance may result in
injury. Do not do anything that makes the appliance
swing to and fro. When moving the appliance up and
down, leave sufficient distance to the appliance.
■
The filter cover may swing out. Always open and
close the filter cover slowly. Ensure that the filter
cover does not swing out after it is released.
■
Risk of trapping body parts when opening and
closing the filter cover. Do not reach into the area
behind the filter cover and keep your hands away
from the hinges.
■
Before cleaning the appliance, disconnect it from the
Home Connect app to ensure that operation via the
Home Connect app is not possible.
■
Risk of injury!
Risk of injury!
Risk of injury!
Cleaning agents
To ensure that the different surfaces are not damaged
by using the wrong cleaning agent, observe the
information in the table. Do not use any of the following:
■
■
■
■
Harsh or abrasive cleaning agents,
Cleaning agents with a high alcohol content,
Hard scouring pads or cleaning sponges,
High-pressure cleaners or steam cleaners.
Wash new sponge cloths thoroughly before use.
en
Follow all instructions and warnings included with the
cleaning agents.
Area
Stainless steel
Cleaning agent
Hot soapy water:
Clean with a dish cloth and then dry with a
soft cloth.
Clean stainless steel surfaces in the grind
direction only.
Special stainless steel cleaning products are
available from our after-sales service or from
specialist retailers. Apply a very thin layer of
the cleaning product with a soft cloth.
Painted surfaces
Hot soapy water:
Clean using a damp dish cloth and dry with a
soft cloth/towel.
Do not use any stainless steel cleaners.
Aluminium and plastic Glass cleaner:
Clean with a soft cloth.
Glass
Glass cleaner:
Clean with a soft cloth. Do not use a glass
scraper.
Controls
Hot soapy water:
Clean using a damp dish cloth and dry with a
soft cloth/towel.
Risk of electric shock caused by penetrating
moisture.
Risk of damage to the electronics from penetrating moisture. Never clean operating controls with a wet cloth.
Do not use any stainless steel cleaners.
Removing the grease filters
: Warning
Risk of injury!
■
Oscillating movement of the appliance may result in
injury. Do not do anything that makes the appliance
swing to and fro. When moving the appliance up and
down, leave sufficient distance to the appliance.
■
The filter cover may swing out. Always open and
close the filter cover slowly. Ensure that the filter
cover does not swing out after it is released.
■
Risk of trapping body parts when opening and
closing the filter cover. Do not reach into the area
behind the filter cover and keep your hands away
from the hinges.
■
If appliances supported by cables are permitted to
swing to and fro, this may overload the fastening
elements. This could cause the appliance to fall off
the wall. Do not do anything that makes the
appliance swing to and fro.
■
Objects left on the hob may tip over when the filter
cover is opened. This can cause burns. Clear the
hob before opening the filter cover.
Risk of injury!
Risk of injury!
Risk of injury!
Risk of injury!
13
en
Cleaning and maintenance
1. Press down on the locks on the filter cover.
Note: The filter cover is heavy. Take the filter cover
by two hands and hold in place.
Cleaning the grease filters
: Warning – Risk of fire!
Fatty deposits in the grease filter may catch fire.
Regularly clean the grease filter. Never operate the
appliance without a grease filter.
Notes
■
Do not use any aggressive, acidic or alkaline
cleaning products.
■
We recommend that you to clean the grease filters
every two months.
■
When cleaning the grease filters, also clean the
grease filter holder in the appliance using a damp
cloth.
■
The grease filters can be cleaned in the dishwasher
or by hand. We recommend cleaning by hand.
By hand:
2. Open the filter cover fully and without pulling on it.
Note: You can use a special degreaser to remove
stubborn dirt. It can be ordered via the online shop.
■
■
■
Soak the grease filters in hot detergent solution.
Clean the filters with a brush and then rinse them
thoroughly.
Allow the grease filters to drain.
In the dishwasher:
Note: Slight discolouration may occur if cleaning in the
dishwasher. This discolouration has no effect on the
performance of the grease filters.
■
3. Open the locking mechanism on the grease filter.
Note: Do not bend the grease filter to avoid causing
damage.
■
■
■
Use normal domestic dishwashing detergents.
Do not clean heavily soiled grease filters together
with tableware.
Place the grease filters in the dishwasher leaving
plenty of space around them. Do not the wedge the
grease filters in.
Select a temperature of no more than 70 °C.
Fitting the grease filters
1. Fit the grease filters.
4. Remove the grease filter from the holder.
Notes
– Fat may accumulate in the bottom of the grease
filter.
– Hold the filter level to prevent fat from dripping
out.
5. Clean the accessible parts of the housing. Clean the
inside of the appliance.
6. Clean the grease filter and let it dry before refitting.
7. Clean the appliance support cables.
Note: Individual wires may protrude out of the
cables.
14
To do this, take hold of the grease filter from
underneath with your other hand.
2. Fold the grease filter upwards and engage the locks.
3. Close the filter cover upwards.
Note: Ensure that the filter cover locks engage
correctly.
Cleaning and maintenance
en
Replacing the odour filter
Replacing the batteries in the remote control
Note: To bind odours in circulating-air mode, you must
install an odour filter. The different options for operating
the appliance in circulating-air mode can be found in
our catalogue. Alternatively, ask your specialist retailer.
The required accessories are available from specialist
retailers, from our after-sales service or from the online
shop.
: Warning
1. Remove the grease filters.
2. Open the odour filter cartridge.
Risk of injury!
Risk of injury!
■
Batteries can be easily swallowed by children. Keep
batteries out of the reach of children. Do not allow
children to change batteries without supervision.
■
Batteries may explode. Do not charge or short-circuit
the batteries. Do not throw batteries into a fire.
■
The connection terminals must not be short
circuited.
■
Only batteries of the specified type may be used.
Different types of batteries or old and new batteries
must not be mixed together.
■
Rechargeable batteries must not be used.
Risk of injury!
Risk of injury!
Risk of injury!
Caution!
Damage to the remote control caused by leaking
batteries. Remove the batteries in the remote control if
the remote control is not being used over a longer
period of time.
1. Remove the cover.
2. Remove the batteries.
3. Remove the old odour filter.
4. Insert the new odour filter.
Note: Note the correct installation direction for the
odour filter.
3. Correctly insert the new batteries (3 V CR 2032).
5. Fit the grease filters.
Caution!
Remove batteries that are flat or defective from the
remote control and dispose of them safely in
accordance with local regulations. Do not dispose of
batteries alongside general household waste.
15
en
Trouble shooting
3Trouble shooting
Malfunctions often have simple explanations. Please
read the following notes before calling the after-sales
service.
Tr oubl e sho t i ng
: Warning – Risk of electric shock!
Incorrect repairs are dangerous. Repairs may only be
carried out and damaged power cables replaced by
one of our trained after-sales technicians. If the
appliance is defective, unplug the appliance from the
mains or switch off the circuit breaker in the fuse box.
Contact the after-sales service.
LED lights
Defective LED lights must only be replaced by the
manufacturer, their customer service department or a
licensed technician (electrician).
Fault
Possible cause
Solution
The appliance is
not working
Power failure
Check whether other kitchen
appliances are working
Check the fuse box to make
sure that the fuse for the
appliance is in working order
Call our after-sales service
The lighting is not The LED lights
working
are faulty
Plug is not correctly plugged
into the filter
cover.
The remote con- The battery is flat
trol is not working
LED 1 or
LED 2 flashes in
the display
Unusual noises
during the
upward or downward movement
of the appliance
A signal tone
sounds three
times
Once the appliance has been
connected to the
power supply, the
lighting switches
on automatically
--------
16
Insert the plug, see the section entitled ~ "Fitting the
filter cover" on page 23
Change the batteries in the
remote control, see section
~ "Replacing the batteries
in the remote control"
on page 15
The grease filter Clean the grease filter or
or the odour filter change the odour filter.
is saturated.
~ "Cleaning and
maintenance" on page 13
Cables may be
Call our after-sales service
damaged
Reference movement was not
started
Demo mode is
switched on
When calling us, please give the product number (E
no.) and the production number (FD no.) so that we can
provide you with the correct advice. The rating plate
with these numbers can be found inside the appliance
(remove the metal mesh grease filter to gain access).
Cust omer ser vi ce
(1U
)'
=1U
7\SH
You can make a note of the numbers of your appliance
and the telephone number of the after-sales service in
the space below to save time should it be required.
E no.
FD no.
After-sales serviceO
Malfunction table
The fuse is faulty
4Customer service
Perform the reference movement using the … and †
buttons
To switch off demo mode:
Press and hold the # and B
buttons for approx. 3 seconds
Please be aware that a visit by an after-sales engineer
will be charged if a problem turns out to be the result of
operator error, even during the warranty period.
Please find the contact data of all countries in the
enclosed customer service list.
To book an engineer visit and product advice
GB
0344 892 8999
Calls charged at local or mobile rate.
IE
01450 2655
0.03 € per minute at peak. Off peak 0.0088 €
per minute.
Rely on the professionalism of the manufacturer. You
can therefore be sure that the repair is carried out by
trained service technicians who carry original spare
parts for your appliances.
Accessories
(not included in the scope of delivery)
Note: These instructions apply to several appliance
models. It may be the case that an optional accessory
that is listed does not apply for your appliance.
Note: Observe the installation instructions in the
accessory.
Accessories
Odour filter (can be regenerated)
Odour filter (cannot be regenerated)
--------
Order number
LZ20JXP00
LZ21JXB16
Installation instructions
en
INSTALLATION INSTRUCTIONS
This appliance is fitted to the kitchen ceiling or a
sturdy suspended ceiling.
The surfaces of the appliance are sensitive. Avoid
damaging them during installation.
Installation instructions
I n s t a l a t i on i n s t r u c t i o n s
■
■
[
[
[
[
PLQ
PP
[
[
PLQ
PP
17
en
Important safety information
(Important safety
information
Read these instructions carefully. Only then
will you be able to operate your appliance
safely and correctly. Retain the instruction
manual and installation instructions for future
use or for subsequent owners.
Check the appliance for damage after
unpacking it. Do not connect the appliance if it
has been damaged in transport.
The appliance can only be used safely if it is
correctly installed according to the safety
instructions. The installer is responsible for
ensuring that the appliance works perfectly at
its installation location.
Only a licensed professional may connect
appliances without plugs. Damage caused by
incorrect connection is not covered under
warranty.
The surfaces of the appliance are easily
damaged. Avoid damaging them during
installation.
For the installation, observe the currently valid
building regulations and the regulations of the
local electricity and gas suppliers.
I mpor t ant saf et y i nf or mat i on
: Warning – Risk of fire!
Fatty deposits in the grease filter may catch
fire. The specified safety clearances must
be complied with in order to prevent a buildup of heat. Refer to the information
provided for your cooker. If gas and electric
hobs are being operated together, the
largest specified clearance applies.
Risk
of fire!deposits in the grease filter may
■
Grease
catch fire. Never work with naked flames
close to the appliance (e.g. flambéing). Do
not install the appliance near a heatproducing appliance for solid fuel (e.g.
wood or coal) unless a closed, nonremovable cover is available. There must
be no flying sparks.
■
: Warning – Risk of injury!
Components inside the appliance may have
sharp edges. Wear protective gloves.
Risk
of injury!
■
The
appliance may fall down if it has not
been properly fastened in place. All
fastening components must be fixed firmly
and securely.
Risk
of injury!
■
The
appliance is heavy. To move the
appliance, 2 people are required. Use only
suitable tools and equipment.
■
18
Risk
of injury!
■
The
appliance is very heavy. The appliance
must not be fitted directly onto plasterboard
or similar lightweight materials. To ensure
correct installation, you must use a material
which is sufficiently stable and suitable for
both the structural conditions and the
weight of the appliance.
Risk
of injury!to the electrical or mechanical
■
Changes
assembly are dangerous and may lead to
malfunctions. Do not make any changes to
the electrical or mechanical assembly.
Risk
of injury!
■
Risk
of falling when working on the
appliance. Use a stable stepladder.
Risk
of injury!
■
Risk
of trapping body parts when opening
and closing the hinges. Keep your hands
away from the hinges.
Risk
of filter
injury!
■
The
cover may swing out. Always open
and close the filter cover slowly. Ensure that
the filter cover does not swing out after it is
released.
: Warning – Risk of electric shock!
Components inside the appliance may have
sharp edges. These may damage the
connecting cable. Do not kink or pinch the
connecting cable during installation.
Risk
of electric
shock!
■
It must
always
be possible to disconnect
the appliance from the electricity supply.
The appliance must only be connected to a
protective contact socket that has been
correctly installed.
The mains plug of the mains power cable
must be easily accessible after installation
of the appliance. If this is not possible, an
all-pole isolating switch must be integrated
into the permanent electrical installation
according to the conditions of overvoltage
category III and according to the installation
regulations.
The permanent electrical installation must
only be wired by a professional electrician.
We recommend installing a residual-current
circuit breaker (RCCB) in the appliance's
power supply circuit.
Risk
of electric
shock!are dangerous. Repairs
■
Incorrect
repairs
may only be carried out and damaged
power cables replaced by one of our
trained after-sales technicians. If the
appliance is defective, unplug the appliance
from the mains or switch off the circuit
breaker in the fuse box. Contact the aftersales service.
■
: Warning – Danger of suffocation!
Packaging material is dangerous to children.
Never allow children to play with packaging
material.
General information
KGeneral information
The surfaces of the appliance are easily damaged.
Avoid damaging them during installation.
Gener al i nf or mat i on
5Installation
I ns t a l a t i o n
Preparing for installation
■
Electrical connection
■
: Warning – Risk of electric shock!
It must always be possible to disconnect the appliance
from the power supply. If there is a fixed connection, an
all-pole isolating switch with a contact gap of at least
3 mm must be provided for the wiring. Only an
electrician may install the fixed connection.We
recommend installing a residual-current circuit breaker
(RCCB) in the appliance's power supply circuit.
: Warning – Risk of electric shock!
Components inside the appliance may have sharp
edges. These may damage the connecting cable. Do
not kink or pinch the connecting cable during
installation.
The required connection data can be found on the
rating plate inside the appliance; remove the odour filter
to access this.
This appliance complies with the EC interference
suppression regulations.
The appliance must be disconnected from the power
supply whenever installation work is being carried out.
When the appliance is installed, protection must be
provided against accidental contact in the future.
en
■
■
Recommended ceiling height up to 3.50 m.
The cooking vapours are more difficult to draw in the
further away they are from the hob. We recommend
a distance of at least 700 mm and a maximum of
1500 mm.
So that cooking vapours are optimally drawn in,
install the extractor hood in the middle of the hob.
The installation site must be easily accessible, so
that the appliance can be accessed freely for
servicing.
Checking the ceiling
■
■
■
■
The ceiling must be flat, horizontal and adequately
load-bearing.
The depth of the bore holes must be the same
length as the screws.
The enclosed screws are suitable only for concrete
ceilings.
The max. weight of the appliance is 80 kg.
Notes
■
When fixing the appliance in place, a suitable
substructure is required that is securely fastened to
the concrete ceiling.
■
Do not fit the appliance directly onto plasterboard (or
similar lightweight materials) in a suspended ceiling.
■
To ensure correct installation, you must use a
material which is sufficiently stable and suitable for
both the structural conditions and the weight of the
appliance.
Preparing the ceiling
1. Cover the hob to protect it from damage.
2. Determine the position of the frame. In doing so,
determine where the middle should be based on the
hob.
3. Measure and mark the positions of the fastening
screws.
4. Drill four holes with a diameter of 6 mm for the fixing.
Caution!
Ensure that there are no electrical wires, gas pipes
or water pipes in the area where holes are to be
drilled.
19
Installation
en
6. Lift the appliance at the corners, turn it over and
Fitting the frame
1. Screw the two opposite screws into the ceiling until
they protrude out of the ceiling by approx. 7 mm.
Note: Note the correct position of the screws and
the frame.
position it on the scissor lift table so that the
appliance is lying on the frame.
Note: Do not place the appliance on the grease
filters as these could be damaged.
PP
PP
7. Leave a gap of at least 700 mm between the hob
2. Guide the frame through the screws on the ceiling.
3. Move the frame so that the screws lock into place in
the key hole openings and can be screwed in tightly.
and the lower edge of the appliance.
Note: When securing cables, ensure that the
maximum distance between the frame cover and the
top edge of the appliance is 1.20 m.
Connecting the appliance
Ensure that there is sufficient fuse protection for the
household wiring. The voltage and frequency of the
appliance must match the electrical wiring (see rating
plate).
The appliance corresponds to protection class 1 and
must only be operated with a protective earth
connection.
The appliance must be disconnected from the power
supply whenever installation work is being carried out.
When the appliance is installed, protection against
contact must be provided.
Only a licensed professional may connect the
appliance. They are subject to the requirements of the
local electricity provider.
: Warning – Risk of electric shock!
4. Align the frame and use two more screws to secure
it in place.
5. Place a scissor lift table or another suitable device
under the appliance.
It must always be possible to disconnect the appliance
from the power supply. If there is a fixed connection, an
all-pole isolating switch with a contact gap of at least
3 mm must be provided for the wiring. Only an
electrician may install the fixed connection.We
recommend installing a residual-current circuit breaker
(RCCB) in the appliance's power supply circuit.
Note: To find out the correct fuse rating, see the total
connected load (in watts) on the appliance's rating
plate.
1. Pull the protective tube over the on-site cable.
Note: Shorten the protective tube where necessary.
20
Installation
2. Plug the on-site cable into the connecting terminal.
en
5. Thread the cables through the openings of the frame
cover.
1
/
6. Undo the strain relief on the cable on the appliance
and pull out the cable.
7. Thread the cable on the appliance through the
3. Thread the four cables into the lock nuts.
Note: Do not insert the lock nuts into the openings to
avoid damaging the appliance's limit switch.
opening in the frame cover and use the strain relief
supplied to secure it.
Caution!
There is a risk of damage to the appliance if the
cable is coiled up. Always secure the cable firmly
using the strain relief so that it does not coil up fully
in the appliance.
4. To protect against scratches, position a spacer on
the appliance and place the frame cover on top of it.
8. Remove the strain relief fitted at the factory.
Note: Keep the strain relief and do not throw it away.
9. Thread four cables into the cable tensioner and
apply equal tension.
Note: Never shorten the cables.
21
en
Installation
10. Adjust the cables if necessary. To do this, relieve the
load on the appliance, loosen the cable tensioner
and push it upwards.
14. Place a scissor lift table or another suitable device
under the appliance.
The appliance hangs on the cables from the ceiling.
15. Pull out the cable on the appliance completely.
Caution!
There is a risk of damage to the appliance if the
cable is coiled up. Hold the cable so that it does not
coil up fully in the appliance.
16. Plug the cable on the appliance into the connecting
terminal and insert it in the strain relief.
1
11. Thread the four enclosed cable clamps and secure
in place approx. 2 cm in front of the cable tensioner.
Note: Tighten the screws by hand.
/
17. Close the cable cover.
18. Carefully lift the frame cover.
19. Place the ends of the cable behind the frame cover.
20. Securely tighten the frame cover with the lock nuts
PP
finger-tight.
Note: Do not use a tool to avoid damaging the frame
cover.
12. Align the appliance using a spirit level.
21. Remove the spacer from the appliance.
22. Connect a power supply.
23. To start the reference movement, press the
13. Remove the protective film from the appliance.
Note: Carefully remove the protective foil around the
cables so that the appliance's limit switch is not
damaged.
22
… button on the remote control.
Note: A reference movement is used to determine
the correct actual position using a reference switch.
The appliance moves upwards.
24. If the appliance has moved fully upwards, press the
† button on the remote control.
The appliance moves downwards. The reference
movement ends when the appliance has moved fully
down.
Installation
Fitting the filter cover
en
5. Insert the on-site cable for the lighting.
: Warning – Risk of injury!
Components inside the appliance may have sharp
edges. Wear protective gloves.
: Warning – Risk of injury!
Risk of trapping body parts when opening and closing
the hinges. Keep your hands away from the hinges.
1. Set the required height of the appliance using the …
and † buttons on the remote control.
Note: If you have not carried out a reference
movement, the appliance automatically moves all the
way upwards and downwards.
2. Open the hinges on the filter cover.
3. Mount the filter cover on the designated screws and
push it backwards/forwards depending on the key
hole opening into the narrow section.
4. Tighten the fastening screws of the hinges.
6. Close the cover on the cable duct.
7. Remove the grease filter.
Note: Do not bend the grease filter to avoid causing
damage.
8. Open the odour filter cartridge.
9. Unpack the odour filter.
23
en
Installation
10. Insert the odour filter.
Note: Note the correct installation direction for the
odour filter.
10. Loosen the cable on the appliance from the
connecting terminal and from the strain relief.
1
Removing the appliance
: Warning – Risk of injury!
Risk of trapping body parts when opening and closing
the hinges. Keep your hands away from the hinges.
: Warning – Risk of injury!
/
11. Fit the grease filters.
12. Swing the filter cover up and ensure that it engages.
11. Secure the cable on the appliance using the strain
relief so that it does not coil up.
Caution!
There is a risk of damage to the appliance if the
cable is coiled up. Always secure the cable firmly
using the strain relief so that it does not coil up fully
in the appliance.
Components inside the appliance may have sharp
edges. Wear protective gloves.
1. Cover the hob to protect it from damage.
2. Press the † button on the remote control.
The appliance moves fully downwards.
3. Place a scissor lift table or another suitable device
under the appliance.
4. Move the scissor lift table up until the tension on the
terminal and remove the protective tube.
1
appliance cables is removed.
Notes
– Place the appliance on the scissor lift table so
that the appliance and the frame are lying on it.
– Do not place the appliance on the grease filters
as these could be damaged.
5. Disconnect the appliance from the power supply.
6. To protect against scratches, position a spacer on
the appliance.
7. Carefully loosen the screws on the frame cover.
Note: Do not use any tools. Ensure that lock nuts do
not fall into the opening in the appliance, in order to
prevent damage to the limit switch.
12. Detach the on-site cable from the connecting
/
13. Loosen the four cable clamps.
8. Place the frame cover down carefully.
9. Open the cable cover at the side using a
screwdriver.
24
Installation
en
14. Open the cable tensioner and pull out the cables.
15. Thread the cables out of the frame cover.
16. Thread the cable on the appliance through the
opening in the frame cover and use the strain relief
to secure it.
Caution!
There is a risk of damage to the appliance if the
cable is coiled up. Always secure the cable firmly
using the strain relief so that it does not coil up fully
in the appliance.
17. Remove the diagonally opposite screws on the
frame.
18. Loosen the two other diagonally opposite screws,
move the frame and remove it.
25
6
6
BSH Hausgeräte GmbH
Carl-Wery-Str. 34
81739 München
GERMANY
Manufactured by BSH Hausgeräte GmbH under Trademark License of Siemens AG
siemens-home.bsh-group.com
*9001442561*
9001442561 (990731)
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising