Siemens | LI60OA520 | Instruction manual | Siemens iQ100 Slimline cooker hood Instruction manual

Siemens iQ100 Slimline cooker hood Instruction manual
Extractor hood
LI60OA520
siemens-home.bsh-group.com/welcome
siemens-home.com/welcome
[en] Instruction manual
Register
your
product
online
Ú Table of contents
e[nuoIrs]ctimanul
Important safety information.....................................................4
Environmental protection ..........................................................5
Saving energy......................................................................................5
Environmentally-friendly disposal.....................................................5
Operating mode..........................................................................5
Exhaust air mode ................................................................................5
Operating the appliance ............................................................6
Controls ................................................................................................6
Filter drawer .........................................................................................6
Switching on the extractor hood ......................................................6
Lighting .................................................................................................6
Cleaning and maintenance ........................................................6
Removing and installing the filter ....................................................7
Replacing bulbs ..................................................................................7
Trouble shooting ........................................................................8
Fault table.............................................................................................8
After-sales service .....................................................................8
Produktinfo
Additional
information on
on products,
products, accessories,
accessories, replacement
replacement
Additional information
parts and
and services
services can
can be
be found
found at
at www.siemens-home.bshwww.siemens-home.com
parts
group.com
and in shop
the online
shop www.siemens-home.bshand in the online
www.siemens-eshop.com
group.com/eshops
3
Important safety information
Read these instructions carefully. Only then will you be able to
operate your appliance safely and correctly. Retain the
instruction manual and installation instructions for future use or
for subsequent owners.
The appliance can only be used safely if it is correctly installed
according to the safety instructions. The installer is responsible
for ensuring that the appliance works perfectly at its installation
location.
This appliance is intended for domestic use and the household
environment only. The appliance is not intended for use
outside. Do not leave the appliance unattended during
operation. The manufacturer is not liable for damage which is
caused by improper use or incorrect operation.
In any case, consult your responsible Master Chimney Sweep.
He is able to assess the house's entire ventilation setup and will
suggest the suitable ventilation measures to you.
Unrestricted operation is possible if the vapour extractor hood
is operated exclusively in the circulating-air mode.
This appliance is intended for use up to a maximum height of
2000 metres above sea level.
: Risk of fire!
This appliance is not intended for use by persons (including
children) with reduced physical, sensory or mental capabilities,
or lack of experience and knowledge, unless they have been
given supervision or instruction concerning use of the
appliance by a person responsible for their safety.
Children must not play with, on, or around the appliance.
Children must not clean the appliance or carry out general
maintenance unless they are at least 8 years old and are being
supervised.
Keep children below the age of 8 years old at a safe distance
from the appliance and power cable.
Check the appliance for damage after unpacking it. Do not
connect the appliance if it has been damaged in transport.
■
Risk of fire!
■
Risk of fire!
■
Risk of fire!
■
This appliance is not intended for operation with an external
clock timer or a remote control.
: Danger of suffocation!
Packaging material is dangerous to children. Never allow
children to play with packaging material.
Risk of fire!
■
: Danger of death!
Risk of poisoning from flue gases that are drawn back in.
Always ensure adequate fresh air in the room if the appliance is
being operated in exhaust air mode at the same time as room
air-dependent heat-producing appliance is being operated.
Grease deposits in the grease filter may catch fire.
Replace the grease filter at least every two months.
Never operate the appliance without the grease filter.
Grease deposits in the grease filter may catch fire. Never
work with naked flames close to the appliance (e.g.
flambéing). Do not install the appliance near a heatproducing appliance for solid fuel (e.g. wood or coal) unless
a closed, non-removable cover is available. There must be no
flying sparks.
Hot oil and fat can ignite very quickly. Never leave hot fat or
oil unattended. Never use water to put out burning oil or fat.
Switch off the hotplate. Extinguish flames carefully using a lid,
fire blanket or something similar.
When gas burners are in operation without any cookware
placed on them, they can build up a lot of heat. A ventilation
appliance installed above the cooker may become damaged
or catch fire. Only operate the gas burners with cookware on
them.
Operating several gas burners at the same time gives rise to
a great deal of heat. A ventilation appliance installed above
the cooker may become damaged or catch fire. Never
operate two gas burners simultaneously on the highest flame
for longer than 15 minutes. One large burner of more than
5 kW (wok) is equivalent to the power of two gas burners.
: Risk of burns!
The accessible parts become very hot when in operation. Never
touch hot parts. Keep children at a safe distance.
: Risk of injury!
■
Components inside the appliance may have sharp edges.
Wear protective gloves.
Items placed on the appliance may fall down. Do not place
any objects on the appliance.
Risk of injury!
■
Room air-dependent heat-producing appliances (e.g. gas, oil,
wood or coal-operated heaters, continuous flow heaters or
water heaters) obtain combustion air from the room in which
they are installed and discharge the exhaust gases into the
open air through an exhaust gas system (e.g. a chimney).
In combination with an activated vapour extractor hood, room
air is extracted from the kitchen and neighbouring rooms - a
partial vacuum is produced if not enough fresh air is supplied.
Toxic gases from the chimney or the extraction shaft are
sucked back into the living space.
■
■
Adequate incoming air must therefore always be ensured.
An incoming/exhaust air wall box alone will not ensure
compliance with the limit.
Safe operation is possible only when the partial vacuum in the
place where the heat-producing appliance is installed does not
exceed 4 Pa (0.04 mbar). This can be achieved when the air
needed for combustion is able to enter through openings that
cannot be sealed, for example in doors, windows, incoming/
exhaust air wall boxes or by other technical means.
4
: Risk of electric shock!
■
A defective appliance may cause electric shock. Never switch
on a defective appliance. Unplug the appliance from the
mains or switch off the circuit breaker in the fuse box.
Contact the after-sales service.
Incorrect repairs are dangerous. Repairs may only be carried
out and damaged power cables replaced by one of our
trained after-sales technicians. If the appliance is defective,
unplug the appliance from the mains or switch off the circuit
breaker in the fuse box. Contact the after-sales service.
Do not use any high-pressure cleaners or steam cleaners,
which can result in an electric shock.
Risk of electric shock!
■
Risk of electric shock!
■
Causes of damage
Caution!
Risk of damage due to corrosion. Always switch on the
appliance while cooking to avoid condensation. Condensate
can produce corrosion damage.
Always replace faulty bulbs to prevent the remaining bulbs from
overloading.
Risk of damage due to ingress of humidity into the electronic
circuitry. Never clean operator controls with a wet cloth.
Surface damage due to incorrect cleaning. Clean stainless
steel surfaces in the direction of the grain only. Do not use any
stainless steel cleaners for operator controls.
Surface damage due to strong or abrasive cleaning agents.
Never use strong and abrasive cleaning agents.
Risk of damage from returning condensate. Install the exhaust
duct in such a way that it falls away from the appliance slightly
(1° slope).
Environmental protection
Your new appliance is particularly energy-efficient. Here you
can find tips on how to save even more energy when using the
appliance, and how to dispose of your appliance properly.
Saving energy
■
■
■
■
During cooking, ensure that there is a sufficient supply of air
so that the extractor hood can work efficiently and with a low
level of operating noise.
Adjust the fan speed to the intensity of the cooking fumes.
Only use intensive mode where this is required. A lower fan
speed means that less energy is consumed.
If there are intensive cooking fumes, select a higher fan
speed in good time. If cooking fumes have already spread in
the kitchen, the extractor hood must be operated for longer.
■
■
Switch off the lighting if you no longer require it.
Clean and, if required, replace the filter at regular intervals in
order to increase the effectiveness of the ventilation system
and to prevent the risk of fire.
Environmentally-friendly disposal
Dispose of packaging in an environmentally-friendly manner.
This appliance is labelled in accordance with
European Directive 2012/19/EU concerning used
electrical and electronic appliances (waste
electrical and electronic equipment - WEEE). The
guideline determines the framework for the return
and recycling of used appliances as applicable
throughout the EU.
Switch off the extractor hood if you no longer require it.
Operating mode
This appliance can be used in air extraction mode.
Exhaust air mode
The air which is drawn in is cleaned by the
grease filters and conveyed to the exterior
by a pipe system.
Note: The air must not be discharged into a flue that is used for
exhausting fumes from appliances burning gas or other fuels
(not applicable to appliances that only discharge the air back
into the room).
Before conveying the exhaust air into a non-functioning smoke
or exhaust gas flue, obtain the consent of the heating engineer
responsible.
5
Operating the appliance
Note: Switch on the extractor hood when you start cooking and
switch it off again several minutes after you have finished
cooking. This is the most effective way of removing the kitchen
fumes.
Controls
Use the toggle switches to set and adjust the various different
functions of your appliance.
Note: The appliance starts with the functions that were set
when the pull-out was closed.
Pushing the filter drawer in
Hold the filter pull-out in the middle and push it in.
Note: The extractor hood and the lighting will switch off when
the pull-out is closed.
Switching on the extractor hood
Switching on
Set the toggle switch to ü.
Extractor hood
ü
Switches on power setting 1
Þ
Switches off the extractor hood
Lighting
[
Switches on/off the lighting
Filter drawer
Pulling out the filter drawer
Hold the filter pull-out in the middle and pull it out.
You can now access the controls and the appliance is ready for
operation.
Note: It can take up to 25 seconds for the backflow preventer
valve to open fully and for the appliance to reach its full
capacity.
Switching off
Set the toggle switch to Þ.
Lighting
The lighting will work even if the extractor hood is switched off.
Switching on
Move the toggle switch to the left.
Switching off
Move the toggle switch to the right.
Cleaning and maintenance
: Risk of burns!
Wash new sponge cloths thoroughly before use.
The appliance becomes hot during operation. Allow the
appliance to cool down before cleaning.
Follow all instructions and warnings included with the cleaning
agents.
: Risk of electric shock!
Area
Cleaning agent
Penetrating moisture may result in an electric shock. Clean the
appliance using a damp cloth only. Before cleaning, pull out the
mains plug or switch off the circuit breaker in the fuse box.
Stainless steel
Hot soapy water:
Clean with a dish cloth and then dry
with a soft cloth.
Clean stainless steel surfaces in the
grind direction only.
: Risk of electric shock!
Do not use any high-pressure cleaners or steam cleaners,
which can result in an electric shock.
Special stainless steel cleaning products are available from our after-sales
service or from specialist retailers.
Apply a very thin layer of the cleaning
product with a soft cloth.
Cleaning agents
To ensure that the different surfaces are not damaged by using
the wrong cleaning agent, observe the information in the table.
Do not use any of the following:
■
Harsh or abrasive cleaning agents,
■
Cleaning agents with a high alcohol content,
■
Hard scouring pads or cleaning sponges,
■
High-pressure cleaners or steam cleaners.
6
Painted surfaces
Hot soapy water:
Clean using a damp dish cloth and dry
with a soft cloth/towel.
Do not use any stainless steel cleaners.
Aluminium and plas- Glass cleaner:
tic
Clean with a soft cloth.
Area
Cleaning agent
In the dishwasher:
Glass
Glass cleaner:
Clean with a soft cloth. Do not use a
glass scraper.
Note: If the metal mesh grease filters are cleaned in the
dishwasher, slight discolouration may occur. This has no effect
on the function of the metal mesh grease filters.
Controls
Hot soapy water:
Clean using a damp dish cloth and dry
with a soft cloth/towel.
Risk of electric shock caused by penetrating moisture.
Risk of damage to the electronics from
penetrating moisture. Never clean
operating controls with a wet cloth.
Do not use any stainless steel cleaners.
Removing and installing the filter
The filter must be serviced regularly in order to guarantee
efficient filtration of odours and grease.
Metal grease filter
The metal grease filters must be cleaned every 100 operating
hours or at least every two months.
: Risk of fire!
Grease deposits in the grease filter may catch fire.
Clean the grease filter at least every 2 months.
Never operate the appliance without the grease filter.
Removing metal grease filter
■
■
Do not clean heavily soiled metal mesh grease filters together
with utensils.
Place the metal mesh grease filters loosely in the dishwasher.
The metal mesh grease filters must not be wedged in.
Installing the metal mesh grease filter
1. Insert metal grease filter.
2. Fold up metal grease filter and engage the lock.
Note: Ensure that the filter cover lock engages correctly.
Replacing bulbs
: Risk of electric shock!
When changing the bulbs, the bulb socket contacts are live.
Before changing the bulb, unplug the appliance from the mains
or switch off the circuit breaker in the fuse box.
: Risk of burns!
Halogen bulbs become very hot when switched on. There is still
a risk of burning for some time after they have been switched
off. Allow the halogen bulbs to cool down before replacing
them.
Important Only use a bulb of the same type and same power
(see also the bulb holder or rating plate).
The metal grease filters filter the grease out of kitchen steam.
To keep them in good working order, the filters should be
cleaned at least every two months.
+6*&8%*
Replacing halogen bulbs
Note: When inserting halogen bulbs, do not touch the glass
bulb. Use a clean cloth to insert the halogen bulbs.
1. Carefully remove the bulb ring using a suitable tool.
1. Hold the filter pull-out by the middle and pull it out.
2. Open the lock on the metal grease filters and remove the
filters from the retainer.
Note: Fat may accumulate in the bottom of the metal grease
filter. Hold the filters level to prevent fat from dripping out.
2. Remove the bulb and replace it with a bulb of the same type.
3. Insert bulb cover.
4. Insert the mains plug or switch on the fuse again.
Replace the bulb with one of the same type:
Voltage: 12 V
3. Clean the metal grease filters and filter cover.
Power: max. 20 W
4. Clean the appliance from the inside.
Socket: G4
Cleaning the metal mesh grease filters
Notes
Do not use any aggressive, acidic or alkaline cleaning
agents.
■
■
■
When cleaning the metal mesh grease filters, also clean the
holder for the metal mesh grease filters in the appliance
using a damp cloth.
The metal mesh grease filters can be cleaned in the
dishwasher or by hand.
By hand:
Note: You can use a special grease solvent for stubborn dirt. It
can be ordered via the Online Shop.
■
Soak the metal mesh grease filters in a hot soapy solution.
■
Clean the filters with a brush and then rinse them thoroughly.
■
Leave the metal mesh grease filters to drain.
7
Trouble shooting
Malfunctions often have simple explanations. Please read the
following notes before calling the after-sales service.
Fault table
: Risk of electric shock!
Problem
Incorrect repairs are dangerous. Repairs may only be carried
out and damaged power cables replaced by one of our trained
after-sales technicians. If the appliance is defective, unplug the
appliance from the mains or switch off the circuit breaker in the
fuse box. Contact the after-sales service.
The lighting does
not work.
After-sales service
Our after-sales service is there for you if your appliance needs
to be repaired. We will always find the right solution in order to
avoid unnecessary visits from a service technician.
When calling us, please give the product number (E no.) and
the production number (FD no.) so that we can provide you with
the correct advice. The rating plate with these numbers can be
found inside the appliance (remove the metal mesh grease
filter to gain access).
You can make a note of the numbers of your appliance and the
telephone number of the after-sales service in the space below
to save time should it be required.
E no.
FD no.
After-sales serviceO
Please be aware that a visit by an after-sales engineer will be
charged if a problem turns out to be the result of operator error,
even during the warranty period.
Please find the contact data of all countries in the enclosed
customer service list.
To book an engineer visit and product advice
GB
0344 892 8999
Calls charged at local or mobile rate.
IE
01450 2655
0.03 € per minute at peak. Off peak 0.0088 € per
minute.
Rely on the professionalism of the manufacturer. You can
therefore be sure that the repair is carried out by trained service
technicians who carry original spare parts for your appliances.
8
Possible cause
The appliance does The plug is not
not work
plugged into the
mains
Solution
Connect the appliance to the power
supply
Power cut
Check whether
other kitchen appliances are working
The fuse is faulty
Check in the fuse
box to make sure
that the fuse for the
appliance is in
working order
The bulbs are faulty. For information on
changing the bulbs,
see the "Replacing
Bulbs" section.
BSH Hausgeräte GmbH
Carl-Wery-Straße 34, 81739 München, GERMANY
siemens-home.com
siemens-home.bsh-group.com
0DQXIDFWXUHGE\%6++DXVJHUlWH*PE+XQGHU7UDGHPDUN/LFHQVHRI6LHPHQV$*
*9001104369*
9001104369
960720
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising