Siemens | LR97CAQ20 | Operating/installations instructions | Siemens iQ500 Ceiling hood Operating/installations instructions

Siemens iQ500 Ceiling hood Operating/installations instructions
Ceiling ventilation
VLHPHQVKRPHEVKJURXSFRPZHOFRPH
[en]Instructions for installation and use
5HJLVWHU
\RXU
SURGXFW
RQOLQH
en
Ú Table of contents
[ e n ] I n s t r u c t i o n s f o r i ns t a l a t i o n a n d u s e
INSTRUCTION MANUAL ..........................................................3
8 Intended use ......................................................... 3
( Important safety information .............................. 4
7 Environmental protection.................................... 6
Ç Operating modes.................................................. 7
1 Operating the appliance ...................................... 7
e Connecting to a hob .......................................... 10
o Home Connect.................................................... 11
2 Cleaning and maintenance................................ 13
3 Trouble shooting................................................ 15
4 Customer service ............................................... 16
INSTALLATION INSTRUCTIONS...........................................17
( Important safety information ............................ 18
K General information ........................................... 20
5 Installation .......................................................... 21
INSTRUCTION MANUAL
Produktinfo
Additional information on products, accessories,
replacement parts and services can be found at
www.siemens-home.bsh-group.com and in the online
shop www.siemens-home.bsh-group.com/eshops
8Intended use
Read these instructions carefully. Only then
will you be able to operate your appliance
safely and correctly. Retain the instruction
manual and installation instructions for future
use or for subsequent owners.
The appliance can only be used safely if it is
correctly installed according to the safety
instructions. The installer is responsible for
ensuring that the appliance works perfectly at
its installation location.
This appliance is intended for domestic use
and the household environment only. The
appliance is not intended for use outside. Do
not leave the appliance unattended during
operation. The manufacturer is not liable for
damage which is caused by improper use or
incorrect operation.
I nt ended us e
This appliance is intended for use up to a
maximum height of 2000 metres above sea
level.
This appliance may be used by children over
the age of 8 years old and by persons with
reduced physical, sensory or mental capacity
or by persons with a lack of experience or
knowledge if they are supervised by someone
who is responsible for their safety, or have
been instructed in how to use the appliance
safely and have understood the risks involved
in not using it properly.
Children must not play with the
appliance.Cleaning and user maintenance
must not be performed by children unless they
are over 15 years of age and are supervised.
Keep children below the age of 8 years old at
a safe distance from the appliance and power
cable.
Check the appliance for damage after
unpacking it. Do not connect the appliance if it
has been damaged in transport.
This appliance is not intended for operation
with an external clock timer or a remote
control.
3
en
Important safety information
:Warning – Danger of suffocation!
Packaging material is dangerous to children.
Never allow children to play with packaging
material.
In any case, consult your responsible Master
Chimney Sweep. He is able to assess the
house's entire ventilation setup and will
suggest the suitable ventilation measures to
you.
Unrestricted operation is possible if the vapour
extractor hood is operated exclusively in the
circulating-air mode.
: Warning – Danger of death!
: Warning – Risk of fire!
(Important safety
information
I mpor t ant saf et y i nf or mat i on
Risk of poisoning from flue gases that are
drawn back in.
Always ensure adequate fresh air in the room
if the appliance is being operated in exhaust
air mode at the same time as room airdependent heat-producing appliance is being
operated.
Room air-dependent heat-producing
appliances (e.g. gas, oil, wood or coaloperated heaters, continuous flow heaters or
water heaters) obtain combustion air from the
room in which they are installed and discharge
the exhaust gases into the open air through an
exhaust gas system (e.g. a chimney).
In combination with an activated vapour
extractor hood, room air is extracted from the
kitchen and neighbouring rooms - a partial
vacuum is produced if not enough fresh air is
supplied. Toxic gases from the chimney or the
extraction shaft are sucked back into the living
space.
■
Adequate incoming air must therefore
always be ensured.
■
An incoming/exhaust air wall box alone will
not ensure compliance with the limit.
Safe operation is possible only when the
partial vacuum in the place where the heatproducing appliance is installed does not
exceed 4 Pa (0.04 mbar). This can be
achieved when the air needed for combustion
is able to enter through openings that cannot
be sealed, for example in doors, windows,
incoming/exhaust air wall boxes or by other
technical means.
Fatty deposits in the grease filter may catch
fire. Regularly clean the grease filter. Never
operate the appliance without a grease
filter.
Risk
of fire!deposits in the grease filter may
■
Grease
catch fire. Never work with naked flames
close to the appliance (e.g. flambéing). Do
not install the appliance near a heatproducing appliance for solid fuel (e.g.
wood or coal) unless a closed, nonremovable cover is available. There must
be no flying sparks.
Risk
of oil
fire!
■
Hot
and fat can ignite very quickly. Never
leave hot fat or oil unattended. Never use
water to put out burning oil or fat. Switch off
the hotplate. Extinguish flames carefully
using a lid, fire blanket or something similar.
Risk
of fire!
■
When
gas burners are in operation without
any cookware placed on them, they can
build up a lot of heat. A ventilation
appliance installed above the cooker may
become damaged or catch fire. Only
operate the gas burners with cookware on
them.
Risk
of fire! several gas burners at the same
■
Operating
time gives rise to a great deal of heat. A
ventilation appliance installed above the
cooker may become damaged or catch fire.
Never operate two gas burners
simultaneously on the highest flame for
longer than 15 minutes. One large burner of
more than 5 kW (wok) is equivalent to the
power of two gas burners.
■
: Warning – Risk of burns!
The accessible parts become very hot when
in operation. Never touch hot parts. Keep
children at a safe distance.
Risk
of burns!
■
The
appliance will become hot during
operation, especially near the bulbs. Allow
the appliance to cool down before cleaning.
■
: Warning – Risk of injury!
Components inside the appliance may have
sharp edges. Wear protective gloves.
Risk of injury!
■
4
Important safety information
The appliance may fall down if it has not
been properly fastened in place. All
fastening components must be fixed firmly
and securely.
Risk
of injury!
■
The
appliance is heavy. To move the
appliance, 2 people are required. Use only
suitable tools and equipment.
Risk
of injury!
■
The
appliance is very heavy. The appliance
must not be fitted directly onto plasterboard
or similar lightweight materials. To ensure
correct installation, you must use a material
which is sufficiently stable and suitable for
both the structural conditions and the
weight of the appliance.
Risk
of injury!to the electrical or mechanical
■
Changes
assembly are dangerous and may lead to
malfunctions. Do not make any changes to
the electrical or mechanical assembly.
Risk
of filter
injury!
■
The
cover may swing out. Always open
and close the filter cover slowly. Ensure that
the filter cover does not swing out after it is
released.
Risk
of injury!
■
Risk
of trapping body parts when opening
and closing the filter cover. Do not reach
into the area behind the filter cover and
keep your hands away from the hinges.
Risk
of injury!can be easily swallowed by
■
Batteries
children. Keep batteries out of the reach of
children. Do not allow children to change
batteries without supervision.
Risk
of injury!may explode. Do not charge or
■
Batteries
short-circuit the batteries. Do not throw
batteries into a fire.
Risk
of injury!
■
The
connection terminals must not be short
circuited.
Risk
of injury!
■
Only
batteries of the specified type may be
used. Different types of batteries or old and
new batteries must not be mixed together.
Risk
of injury!
■
Rechargeable
batteries must not be used.
Risk of injury!
■
■
en
Use a stable ladder and make sure it is in a
secure position. Do not lean over the hob
and do not step on the work surface or the
hob.
Risk
of injury!
■
Risk
of falling when working on the
appliance. Use a stable stepladder.
Risk
of injury!
■
Before
cleaning the appliance, disconnect it
from the Home Connect app to ensure that
operation via the Home Connect app is not
possible.
: Warning – Risk of electric shock!
A defective appliance may cause electric
shock. Never switch on a defective
appliance. Unplug the appliance from the
mains or switch off the circuit breaker in the
fuse box. Contact the after-sales service.
Risk
of electric
shock!are dangerous. Repairs
■
Incorrect
repairs
may only be carried out and damaged
power cables replaced by one of our
trained after-sales technicians. If the
appliance is defective, unplug the appliance
from the mains or switch off the circuit
breaker in the fuse box. Contact the aftersales service.
Risk
of electric shock!
■
Penetrating
moisture may result in an
electric shock. Clean the appliance using a
damp cloth only. Before cleaning, pull out
the mains plug or switch off the circuit
breaker in the fuse box.
Risk
electric
■
Doofnot
use shock!
any high-pressure cleaners or
steam cleaners, which can result in an
electric shock.
■
5
en
Environmental protection
Causes of damage
Caution!
Risk of damage due to corrosion. Always
switch on the appliance while cooking to avoid
condensation. Condensate can produce
corrosion damage.
Always replace faulty bulbs to prevent the
remaining bulbs from overloading.
Risk of damage due to ingress of humidity into
the electronic circuitry. Never clean operator
controls with a wet cloth.
Surface damage due to incorrect cleaning.
Clean stainless steel surfaces in the direction
of the grain only. Do not use any stainless
steel cleaners for operator controls.
Surface damage due to strong or abrasive
cleaning agents. Never use strong and
abrasive cleaning agents.
Risk of damage as a result of incorrect
loading of design elements. Do not pull design
elements.Do not place objects on the design
elements or hang objects from them.
Caution!
Damage to the remote control caused by
leaking batteries. Remove the batteries in the
remote control if the remote control is not
being used over a longer period of time.
Caution!
Remove batteries that are flat or defective
from the remote control and dispose of them
safely in accordance with local regulations. Do
not dispose of batteries alongside general
household waste.
7Environmental protection
Your new appliance is particularly energy-efficient.
Here you can find tips on how to save even more
energy when using the appliance, and how to dispose
of your appliance properly.
Envi r onment al pr ot ect i on
Saving energy
■
■
■
■
■
■
■
During cooking, ensure that there is a sufficient
supply of air to enable the extractor hood to work
efficiently and with a low level of operating noise.
Adjust the fan speed to the amount of steam
produced during cooking. Only use intensive mode
when required. The lower the fan speed, the less
energy is consumed.
If cooking produces large amounts of steam, select
a higher fan speed in good time. If the cooking
steam has already spread around the kitchen, the
extractor hood will need to be operated for longer.
Switch off the extractor hood if you no longer require
it.
Switch off the lighting if you no longer require it.
Clean and (if required) replace the filter at regular
intervals in order to increase the effectiveness of the
ventilation system and to prevent the risk of fire.
Put the lid on to reduce cooking steam and
condensation.
Environmentally-friendly disposal
Dispose of packaging in an environmentally-friendly
manner.
This appliance is labelled in accordance with
European Directive 2012/19/EU concerning
used electrical and electronic appliances
(waste electrical and electronic equipment WEEE). The guideline determines the
framework for the return and recycling of used
appliances as applicable throughout the EU.
Disposing of batteries
Dispose of used batteries in an environmentally friendly
manner.
Batteries must not be disposed of in the
household waste after use. Consumers are
obliged by law to return all used batteries to a
retailer or other collection points.
The retailer is obliged to take back used
batteries free of charge.
6
Operating modes
en
ÇOperating modes
1Operating the appliance
Exhaust air mode
These instructions apply to several appliance variants.
It is possible that individual features are described
which do not apply to your appliance.
If your appliance has Home Connect, more functions
are only available in the Home Connect app.
Oper at i ng modes
The air which is drawn in is cleaned
by the grease filters and conveyed to
the exterior by a pipe system.
Note: The exhaust air must not be conveyed into a
functioning smoke or exhaust gas flue or into a shaft
which is used to ventilate installation rooms which
contain heat-producing appliances.
■
■
Before conveying the exhaust air into a nonfunctioning smoke or exhaust gas flue, obtain the
consent of the heating engineer responsible.
If the exhaust air is conveyed through the outer wall,
a telescopic wall box should be used.
Oper at i ng t he ap l i ance
Note: Switch on the extractor hood when you start
cooking and switch it off again several minutes after you
have finished cooking. This is the most effective way of
removing the kitchen fumes.
Remote control
Use the remote control to set and adjust the various
different functions of your appliance.
Note: Align the remote control as precisely as possible
to the infrared receiver for the LED display.
Circulating-air mode
The air which is drawn in is cleaned by
the grease filters and an activated
carbon filter and conveyed back into the
kitchen.
Note: To bind odours in circulating-air mode, you must
install an activated carbon filter. The different options for
operating the appliance in circulating-air mode can be
found in the brochure. Alternatively, ask your dealer.
The required accessories are available from specialist
retailers, from customer service or from the Online
Shop.
Symbol
#
w
B
x
}
@
A
y
D
y
Explanation
On/Off
Automatic mode/climateControl sensor
Light on/off
Reducing the brightness
Increasing the brightness
Increasing the fan setting
Decreasing the fan setting
Fan run-on
Home Connect
Resetting filter saturation
7
Operating the appliance
en
LED display
Switching off
Press the y button.
This immediately stops the fan run-on.
Intermittent ventilation
LED
1
2
3
4
5
6
7
8
Explanation
Fan setting 1
Fan setting 2
Fan setting 3
Intensive mode 1
Intensive mode 2
Automatic mode / fan run-on time / interval ventilation
Home Connect
Infrared receiver
Setting the fan
Switching on
1. Press the # button.
The fan starts at fan setting 2.
2. Press the @ or A button to set a different fan setting.
The corresponding LEDs light up on the appliance.
Note: The appliance has 3 fan settings and 2 intensive
modes.
Switching off
Press the # button.
Intensive setting
You can use the intensive setting if there is a large
build-up of odours and fumes/vapours.
Switching on
1. Press the # button.
The fan starts at fan setting 2.
2. Press the @ button twice in order to set intensive
mode 1.
3. Press the @ button three times in order to set
intensive mode 2.
The corresponding LEDs light up on the appliance.
Note: After approx. 6 minutes, the extractor hood
automatically switches back to fan setting 3.
This function is only available in the Home Connect app.
With interval ventilation, the ventilation system switches
on and off in the selected setting for the selected time.
LED 6 flashes continuously, the LED for the selected
ventilation setting lights up on the appliance.
As soon as the ventilation duration comes to an end,
the LED for the ventilation setting you have selected
goes out. LED 6 continues to flash.
Automatic mode
Switching on
1. Press the # button.
The fan starts at fan setting 2. The corresponding
LEDs light up.
2. Press the w button.
LED 6 on the appliance lights up and the optimum
fan setting is set automatically via a sensor.
Switching off
Switch off automatic mode using the w button.
The fan switches itself off automatically if the sensor
detects no further change in the air quality of the room.
Automatic mode can run for a maximum of four hours.
Sensor control
In automatic mode, a sensor in the extractor hood
detects the intensity of the cooking and roasting
odours. Depending on the sensor setting, the fan
automatically switches itself to another fan setting.
Possible sensor settings:
Default sensitivity setting: LED 3 (fan setting 3)
Lowest sensitivity setting: LED 1 (fan setting 1)
Highest sensitivity setting: LED 5 (intensive mode 2)
If the sensor control responds too strongly or not
enough, it can be changed accordingly:
1. When the appliance is switched off, press and hold
the # and w buttons for approx. 3 seconds.
2. Press the @ or A button to change the sensor control
setting.
Fan run-on time
Switching on
Press the y button.
The fan runs at fan setting 1. LED 1 on the appliance
lights up, LED 6 flashes.
After approx. 10 minutes, the fan switches off
automatically.
8
3. Press and hold the # and w buttons for approx.
3 seconds to save the setting or wait for approx.
10 seconds until the setting is automatically saved.
A signal tone will sound.
Note: Press the # button to cancel the setting.
Operating the appliance
Saturation display
Button tone
When the metal grease filters or the air recirculation
filter are saturated after the appliance has been
switched off, the corresponding symbols flash and a
repeated signal tone sounds:
Switching on or off
■
■
■
Metal grease filter: LED 1 flashes
Air recirculation filter: LED 2 flashes
Metal grease filter and air recirculation filter: LEDs
1 and 2 flash
If you have not yet done so, the metal grease filters
should now be cleaned or the air recirculation filter
replaced. ~ "Cleaning and maintenance" on page 13
The saturation indicators can be reset while they are
flashing. To do this, press the y button.
Switching over to circulating-air mode
For circulating-air mode, the electronic controller must
be switched over accordingly.
en
Note: Only button tones can be switched on and off.
Signal tones on the appliance cannot be switched off.
1. When the appliance is switched off, press and hold
the # and A buttons for approx. 3 seconds.
The LED in the currently selected setting lights up.
2. Press the @ or A button to change the setting.
The button tones are switched on if LED 1 lights up
on the appliance.
The button tones are switched off if LED 2 lights up
on the appliance.
3. Press and hold the # and A buttons for approx.
3 seconds to save the setting or wait for approx.
10 seconds until the setting is automatically saved.
A signal tone will sound.
Note: Press the # button to cancel the setting.
1. When the appliance is switched off, press and hold
2.
3.
4.
5.
the # and y buttons for approx. 3 seconds.
The LED for the currently active filter setting lights up
on the appliance.
Press the @ button/A button until LED 2 for
circulating-air mode (filter cannot be regenerated)
lights up on the appliance.
Press the @ button/ A button until LED 3 for
circulating-air mode (filter can be regenerated) lights
up on the appliance.
Press the @ button/A button until LED 1 on the
appliance for the electronic controller is switched
back to operation without air recirculation filter.
Press and hold the # and y buttons for approx.
3 seconds to save the setting or wait for approx.
10 seconds until the setting is automatically saved.
A signal tone will sound.
Note: Press the # button to cancel the setting.
Lighting
The lighting can be switched on and off independently
of the fan.
Press the B button.
Setting the brightness
Press and hold the x or } button until the required
brightness is reached.
Note: Colour temperature settings are available in the
Home Connect app provided the appliance has this
function.
9
en
Connecting to a hob
eConnecting to a hob
You can connect this appliance to a hob (if the hob
supports connection to the appliance) and then control
the functions of the hood via your hob.
Appliances can be connected to each other in different
ways:
Home Connect
Two appliances can be connected using the Home
Connect app provided that both of them are Home
Connect compatible.
Refer to the Home Connect documents supplied for
more information.
Con ect i ng t o a hob
Connecting appliances via your home network
If the appliances are connected to each other via your
home network, both the hood controls on the hob and
Home Connect can be used to operate the appliance.
Notes
Make sure you follow the safety instructions in the
instruction manual for your extractor hood and that
these are complied with even when operating the
appliance via the hood controls on the hob.
■
If the extractor hood is being operated by means of
the controls on the hood itself, this mode of
operation always has priority. It is not possible to use
the hood controls on the hob during this time.
■
Setting up a connection
The hood must be switched off before you can connect
the hob and extractor hood.
Connecting directly
Make sure that the hob is switched on and is in search
mode.
To do this, refer to the section entitled "Connecting to
the extractor hood" in the instruction manual for your
hob.
Notes
■
Before connecting the appliance, reset all existing
connections to the WiFi or other appliances.
■
If your extractor hood is connected directly to the
hob, it cannot be connected to your WiFi as well and
you will not be able to use Home Connect.
Connecting appliances directly
If the appliance is connected directly to a hob, it cannot
be connected to your home network as well. The
appliance will function as an extractor hood that is not
connected to the network and you can continue to
operate it via the control panel.
10
Press and hold the D button until the Home Connect
LED starts flashing.
The extractor hood has been connected to the hob
when the Home Connect LED stops flashing and
remains continuously lit.
Connecting via your home network
Follow the instructions in the section entitled "Automatic
login to your home network" or "Manually logging into
your home network" ~ "Home Connect" on page 11
Once the extractor hood is connected to your home
network, you can connect to the hob via the Home
Connect app. To do this. follow the instructions on your
mobile device.
Home Connect
oHome Connect
This appliance can be networked and also controlled
using a mobile device.
If the appliance is not connected to your home network,
it will function as an extractor hood with no network
connection and can still be operated via the display.
The availability of the Home Connect function depends
on the availability of Home Connect services in your
country. Home Connect services are not available in
every country. You can find more information on this at
www.home-connect.com.
Home Con ect
Notes
■
Ensure that you follow the safety instructions in this
instruction manual and that you comply with these
even when you are away from home and are
operating the appliance via the Home Connect app.
You must also follow the instructions in the Home
Connect app.
■
Operating the appliance directly from the appliance
always takes priority. It is not possible to operate the
appliance using the Home Connect app during this
time.
Setting up
To implement settings via Home Connect, you must
have installed and set up the Home Connect app on
your mobile device.
Refer to the Home Connect documents supplied for
more information.
The app will guide you through the entire registration
process. Follow the steps specified by the app to
implement the settings.
The app must be open in order to perform the set-up
process.
en
3. Press the WPS button on the router within the next
2 minutes.
If the extractor hood has successfully connected, it
will automatically connect to the Home Connect app.
LED 3 and LED 7 will flash.
Note: If the extractor hood has been unable to
connect, it will automatically allow you to manually
connect to your home network. The LED for fan
setting 2 and the Home Connect LED will flash. Log
the appliance into your home network manually or
press the A button to try logging in automatically
again.
4. On your mobile device, follow the instructions for
automatic network login.
The login process is complete when LED 7 on the
appliance stops flashing and remains continuously lit.
Manual registration in the home network
Notes
■
The extractor hood cannot be switched on during the
connection process. You can cancel the process at
any time by pressing the # symbol.
■
To connect the extractor hood to your home
network, the hood and the light must be switched off.
1. Press and hold the D button until LED 7 on the
appliance flashes.
2. Press the @ button twice to start logging into your
home network manually.
LED 2 and LED 7 will flash.
3. Follow the instructions in the app.
Notes
■
In networked standby mode, your appliance requires
a maximum of 2 W.
■
If you need your device's MAC address to connect to
your home network, you can find this next to the
rating plate inside the appliance (you will need to
remove the filter to see it).
Automatic registration in the home network
Notes
■
You need a router that has WPS functionality.
■
You need to be able to access your router. If you do
not have this, follow the steps for "Manually logging
into your home network".
■
The extractor hood cannot be switched on during the
connection process. You can cancel the process at
any time by pressing the # symbol.
■
To connect the extractor hood to your home
network, the hood and the light must be switched off.
If the extractor hood has successfully connected, it
will automatically connect to the Home Connect app.
LED 3 and LED 7 will flash.
4. On your mobile device, follow the instructions for
manually logging into your network.
The login process is complete when LED 7 on the
appliance stops flashing and remains continuously lit.
1. Press and hold the D button until LED 7 on the
appliance flashes.
2. Press the @ button.
LED 1 and LED 7 will flash.
11
en
Home Connect
Connecting to the app
If the Home Connect app is installed on your mobile
device, you can connect it to your extractor hood.
Notes
■
The appliance must be connected to the network.
■
The app must be open.
1. Press and hold the D button until LED 3 and LED
7 start flashing.
2. On your mobile device, follow the instructions in the
Home Connect app.
The connection process is complete when LED 7 on the
appliance stops flashing and remains continuously lit.
Resetting the connection
You can reset the connections you have saved on your
home network and on Home Connect at any time.
Press and hold the w and @ buttons until LED 7 on the
appliance goes out. An audible signal will sound.
About data protection
When your appliance is connected for the first time to a
WLAN network, which is connected to the Internet, your
appliance transmits the following categories of data to
the Home Connect server (initial registration):
■
Software update
Using the software update function, your extractor
hood's software can be updated (e.g. for the purpose of
optimisation, troubleshooting or security updates). To
do this, you need to be a registered Home Connect
user, have installed the app on your mobile device and
be connected to the Home Connect server.
As soon as a software update is available, you will be
informed through the Home Connect app and will be
able to start the software update via the app.
Once the update has been successfully downloaded,
you can start installing it via the Home Connect app if
you are on your local area network.
The Home Connect app will inform you once installation
is complete.
Notes
■
You can continue to use your extractor hood as
normal while updates are downloading.
■
Depending on your personal settings in the app,
software updates can also be set to download
automatically.
■
We recommend that you install security updates as
soon as possible.
■
■
■
Unique appliance identification (consisting of
appliance codes as well as the MAC address of the
installed WiFi communication module).
Security certificate of the WiFi communication
module (to ensure a secure IT connection).
The current software and hardware version of your
domestic appliance.
Status of any previous resetting to factory settings.
This initial registration prepares the Home Connect
functions for use and is only required when you want to
use these Home Connect functions for the first time.
Note: Ensure that the Home Connect functions can be
used only in conjunction with the Home Connect app.
Information on data protection can be accessed in the
Home Connect app.
Declaration of Conformity
BSH Hausgeräte GmbH hereby declares that the
appliance which features Home Connect is in
accordance with the basic requirements and the other
relevant provisions of the directive 2014/53/EU.
A detailed RED Declaration of Conformity can be found
online at www.siemens-home.bsh-group.com on the
product page of your appliance with the additional
documents.
Remote diagnostics
If a fault occurs, the after-sales service can use remote
diagnostics to access your appliance.
Contact the after-sales service, making sure that your
appliance is connected to the Home Connect server
and checking that the remote diagnostics service is
available in your country.
Note: For more information and to check whether the
remote diagnostics service is available in your country,
please visit the Help & Support area of the Home
Connect website for your country: www.homeconnect.com
12
2.4 GHz band: max. 100 mW
5 GHz band: max. 100 mW
BE
BG
CZ
ES
FR
HR
HU
MT
NL
SK
FI
SE
5 GHz Wi-Fi: for indoor use only
y
DK
IT
AT
UK
DE
CY
PL
NO
EE
LV
PT
CH
IE
LT
RO
TR
EL
LU
SI
Cleaning and maintenance
2Cleaning and maintenance
Cl eani ng and mai nt enance
:Warning – Risk of burns!
The appliance will become hot during operation,
especially near the bulbs. Allow the appliance to cool
down before cleaning.
: Warning
Risk of electric shock!
Penetrating moisture may result in an electric shock.
Clean the appliance using a damp cloth only. Before
cleaning, pull out the mains plug or switch off the
circuit breaker in the fuse box.
■
Do not use any high-pressure cleaners or steam
cleaners, which can result in an electric shock.
■
Risk of electric shock!
: Warning
Risk of injury!
The filter cover may swing out. Always open and
close the filter cover slowly. Ensure that the filter
cover does not swing out after it is released.
■
Risk of trapping body parts when opening and
closing the filter cover. Do not reach into the area
behind the filter cover and keep your hands away
from the hinges.
■
Before cleaning the appliance, disconnect it from the
Home Connect app to ensure that operation via the
Home Connect app is not possible.
■
Risk of injury!
Risk of injury!
Cleaning agents
To ensure that the different surfaces are not damaged
by using the wrong cleaning agent, observe the
information in the table. Do not use any of the following:
■
■
■
■
Harsh or abrasive cleaning agents,
Cleaning agents with a high alcohol content,
Hard scouring pads or cleaning sponges,
High-pressure cleaners or steam cleaners.
Wash new sponge cloths thoroughly before use.
en
Follow all instructions and warnings included with the
cleaning agents.
Area
Stainless steel
Cleaning agent
Hot soapy water:
Clean with a dish cloth and then dry with a
soft cloth.
Clean stainless steel surfaces in the grind
direction only.
Special stainless steel cleaning products are
available from our after-sales service or from
specialist retailers. Apply a very thin layer of
the cleaning product with a soft cloth.
Painted surfaces
Hot soapy water:
Clean using a damp dish cloth and dry with a
soft cloth/towel.
Do not use any stainless steel cleaners.
Aluminium and plastic Glass cleaner:
Clean with a soft cloth.
Glass
Glass cleaner:
Clean with a soft cloth. Do not use a glass
scraper.
Controls
Hot soapy water:
Clean using a damp dish cloth and dry with a
soft cloth/towel.
Risk of electric shock caused by penetrating
moisture.
Risk of damage to the electronics from penetrating moisture. Never clean operating controls with a wet cloth.
Do not use any stainless steel cleaners.
Cleaning the metal mesh grease filters
These instructions apply to several appliance variants. It
is possible that individual features are described which
do not apply to your appliance.
: Warning – Risk of fire!
Fatty deposits in the grease filter may catch fire.
Regularly clean the grease filter. Never operate the
appliance without a grease filter.
Notes
■
Do not use any aggressive, acidic or alkaline
cleaning products.
■
We recommend cleaning the grease filters every
2 months.
■
When cleaning the metal grease filters, also clean
the metal grease filter holder in the appliance using
a damp cloth.
■
The metal grease filters can be cleaned in the
dishwasher or by hand. We recommend cleaning by
hand.
13
en
Cleaning and maintenance
By hand:
Note: You can use a special grease solvent for
stubborn dirt. It can be ordered via the Online Shop.
■
■
■
Note: The filter cover may swing out. Always open
and close the filter cover slowly. Ensure that the filter
cover does not swing out after it is released.
Soak the metal mesh grease filters in a hot soapy
solution.
Clean the filters with a brush and then rinse them
thoroughly.
Leave the metal mesh grease filters to drain.
In the dishwasher:
Note: Slight discolouration may occur if the metal
grease filters are cleaned in the dishwasher. This
discolouration has no effect on the performance of the
metal grease filters.
■
■
■
■
Use normal domestic dishwashing detergents.
Do not clean heavily soiled metal grease filters
together with cookware.
Place the metal grease filters in the dishwasher,
leaving plenty of space around them. Do not trap the
metal grease filters.
Select a temperature of no more than 70 °C.
3. Open the lock.
Note: To avoid causing damage, do not bend the
metal grease filter.
Removing metal grease filter
: Warning – Risk of injury!
Use a stable ladder and make sure it is in a secure
position. Do not lean over the hob and do not step on
the work surface or the hob.
4. Take the metal grease filter out of the holder.
: Warning – Risk of injury!
The filter cover may swing out. Always open and close
the filter cover slowly. Ensure that the filter cover does
not swing out after it is released.
1. Press the lock on the filter cover.
Note: The filter cover is heavy. Take the filter cover
by two hands and hold in place.
2. Open the filter cover fully and without pulling on it.
14
Notes
– Fat may accumulate in the bottom of the metal
grease filter.
– Hold the metal grease filter level to prevent fat
from dripping out.
5. Clean the inside of the appliance.
6. Clean the metal grease filter and let it dry before
refitting.
Installing the metal mesh grease filter
1. Insert metal grease filter.
While doing this, place your other hand under the
metal grease filter.
2. Fold up metal grease filter and engage the lock.
3. Close the filter cover upwards.
Note: Ensure that the filter cover lock engages
correctly.
Trouble shooting
Replacing the batteries in the remote control
: Warning
Risk of injury!
Batteries can be easily swallowed by children. Keep
batteries out of the reach of children. Do not allow
children to change batteries without supervision.
■
Batteries may explode. Do not charge or short-circuit
the batteries. Do not throw batteries into a fire.
■
The connection terminals must not be short
circuited.
■
Only batteries of the specified type may be used.
Different types of batteries or old and new batteries
must not be mixed together.
■
Rechargeable batteries must not be used.
■
Risk of injury!
Risk of injury!
Risk of injury!
en
3Trouble shooting
Malfunctions often have simple explanations. Please
read the following notes before calling the after-sales
service.
Tr oubl e sho t i ng
: Warning – Risk of electric shock!
Incorrect repairs are dangerous. Repairs may only be
carried out and damaged power cables replaced by
one of our trained after-sales technicians. If the
appliance is defective, unplug the appliance from the
mains or switch off the circuit breaker in the fuse box.
Contact the after-sales service.
Risk of injury!
Caution!
Damage to the remote control caused by leaking
batteries. Remove the batteries in the remote control if
the remote control is not being used over a longer
period of time.
1. Remove the cover.
2. Remove the batteries.
LED lights
Defective LED lights must only be replaced by the
manufacturer, their customer service department or a
licensed technician (electrician).
Malfunction table
Fault
Possible cause
Solution
The appliance
does not work
The plug is not
plugged into the
mains
Power cut
Connect the appliance to the
power supply
The fuse is faulty
3. Correctly insert the new batteries (3 V CR 2032).
Caution!
Remove batteries that are flat or defective from the
remote control and dispose of them safely in
accordance with local regulations. Do not dispose of
batteries alongside general household waste.
Check whether other kitchen
appliances are working
Check in the fuse box to make
sure that the fuse for the
appliance is in working order
Call the after-sales service
The lighting is not The LED lights
working
are defective
The remote con- The battery is flat Change the batteries in the
trol is not working
remote control, see section
~ "Replacing the batteries
in the remote control"
on page 15
After the appliThe battery is
Change the batteries in the
ance has been
nearly flat
remote control, see section
switched off, the
~ "Replacing the batteries
LEDs 1-5 flash
in the remote control"
three times.
on page 15
LED 1 or LED 2
The metal grease Clean the metal grease filter
flashes in the dis- filter or the acti- or replace the activated charplay
vated charcoal fil- coal filter. ~ "Cleaning the
ter is saturated.
metal mesh grease filters"
on page 13
--------
15
Customer service
en
4Customer service
Accessories
When calling us, please give the product number (E
no.) and the production number (FD no.) so that we can
provide you with the correct advice. The rating plate
with these numbers can be found inside the appliance
(remove the metal mesh grease filter to gain access).
Note: These instructions apply to several appliance
models. It may be the case that an optional accessory
that is listed does not apply for your appliance.
Cust omer ser vi ce
(1U
)'
=1U
7\SH
You can make a note of the numbers of your appliance
and the telephone number of the after-sales service in
the space below to save time should it be required.
E no.
FD no.
After-sales serviceO
Please be aware that a visit by an after-sales engineer
will be charged if a problem turns out to be the result of
operator error, even during the warranty period.
Please find the contact data of all countries in the
enclosed customer service list.
To book an engineer visit and product advice
GB
0344 892 8999
Calls charged at local or mobile rate.
IE
01450 2655
0.03 € per minute at peak. Off peak 0.0088 €
per minute.
Rely on the professionalism of the manufacturer. You
can therefore be sure that the repair is carried out by
trained service technicians who carry original spare
parts for your appliances.
16
(not included in the scope of delivery)
Note: Observe the installation instructions in the
accessory.
Accessory/ies
CleanAir recirculation module with easy-change
filter (cannot be regenerated), stainless steel
CleanAir recirculation module with filter (can be
regenerated), stainless steel
CleanAir recirculation module with easy-change
filter (can be regenerated), white
CleanAir recirculation module with filter (can be
regenerated), white
Easy-change filter for circulating-air mode (cannot
be regenerated)
Filter for air recirculation module (can be regenerated)
--------
Order number
LZ20JCC50
LZ20JCD50
LZ20JCC20
LZ20JCD20
LZ56200
LZ00XXP00
Installation instructions
en
INSTALLATION INSTRUCTIONS
I nst al at i on i nst r uct i onsInstallation instructions
■
■
This appliance is fitted to the kitchen ceiling or a
sturdy suspended ceiling.
The surfaces of the appliance are sensitive. Avoid
damaging them during installation.
PLQ
PP
PD[
PP
PLQ
PP
PLQ
PP
PLQ
PP
PLQ
PP
D
E
PD[
PP
PLQ
PP
;
;
;
D
E
17
en
Important safety information
(Important safety
information
Read these instructions carefully. Only then
will you be able to operate your appliance
safely and correctly. Retain the instruction
manual and installation instructions for future
use or for subsequent owners.
Check the appliance for damage after
unpacking it. Do not connect the appliance if it
has been damaged in transport.
The appliance can only be used safely if it is
correctly installed according to the safety
instructions. The installer is responsible for
ensuring that the appliance works perfectly at
its installation location.
Only a licensed professional may connect
appliances without plugs. Damage caused by
incorrect connection is not covered under
warranty.
The surfaces of the appliance are easily
damaged. Avoid damaging them during
installation.
For the installation, observe the currently valid
building regulations and the regulations of the
local electricity and gas suppliers.
I mpor t ant saf et y i nf or mat i on
Room air-dependent heat-producing
appliances (e.g. gas, oil, wood or coaloperated heaters, continuous flow heaters
or water heaters) obtain combustion air
from the room in which they are installed
and discharge the exhaust gases into the
open air through an exhaust gas system
(e.g. a chimney).
In combination with an activated vapour
extractor hood, room air is extracted from
the kitchen and neighbouring rooms - a
partial vacuum is produced if not enough
fresh air is supplied. Toxic gases from the
chimney or the extraction shaft are sucked
back into the living space.
– Adequate incoming air must therefore
always be ensured.
– An incoming/exhaust air wall box alone
will not ensure compliance with the limit.
Safe operation is possible only when the
partial vacuum in the place where the heatproducing appliance is installed does not
exceed 4 Pa (0.04 mbar). This can be
achieved when the air needed for
combustion is able to enter through
openings that cannot be sealed, for
example in doors, windows, incoming/
exhaust air wall boxes or by other technical
means.
: Warning – Risk of death!
Risk of poisoning from flue gases that are
drawn back in. The exhaust air must not be
conveyed into a functioning smoke or
exhaust gas flue or into a shaft which is
used to ventilate installation rooms that
contain heating appliances. If the exhaust
air is to be conveyed into a non-functioning
smoke or exhaust gas flue, you must obtain
the consent of the heating engineer
responsible.
Danger
■
Risk of
ofdeath!
poisoning from flue gases that are
drawn back in.
Always ensure adequate fresh air in the
room if the appliance is being operated in
exhaust air mode at the same time as room
air-dependent heat-producing appliance is
being operated.
■
18
In any case, consult your responsible
Master Chimney Sweep. He is able to
assess the house's entire ventilation setup
and will suggest the suitable ventilation
measures to you.
Unrestricted operation is possible if the
vapour extractor hood is operated
exclusively in the circulating-air mode.
Danger
■
Risk of
ofdeath!
poisoning from flue gases that are
drawn back in. If installing a ventilation
system in a room with a heat-producing
appliance connected to a chimney/flue, the
electricity supply to the hood must be
equipped with a suitable safety switch.
Important safety information
: Warning – Risk of fire!
Fatty deposits in the grease filter may catch
fire. The specified safety clearances must
be complied with in order to prevent a buildup of heat. Refer to the information
provided for your cooker. If gas and electric
hobs are being operated together, the
largest specified clearance applies.
Risk
of fire!deposits in the grease filter may
■
Grease
catch fire. Never work with naked flames
close to the appliance (e.g. flambéing). Do
not install the appliance near a heatproducing appliance for solid fuel (e.g.
wood or coal) unless a closed, nonremovable cover is available. There must
be no flying sparks.
When conveying the exhaust air, official and
legal regulations (e.g. state building
regulations) must be followed.
■
: Warning – Risk of injury!
Components inside the appliance may have
sharp edges. Wear protective gloves.
Risk
of injury!
■
The
appliance may fall down if it has not
been properly fastened in place. All
fastening components must be fixed firmly
and securely.
Risk
of injury!
■
The
appliance is heavy. To move the
appliance, 2 people are required. Use only
suitable tools and equipment.
Risk
of injury!
■
The
appliance is very heavy. The appliance
must not be fitted directly onto plasterboard
or similar lightweight materials. To ensure
correct installation, you must use a material
which is sufficiently stable and suitable for
both the structural conditions and the
weight of the appliance.
Risk
of injury!to the electrical or mechanical
■
Changes
assembly are dangerous and may lead to
malfunctions. Do not make any changes to
the electrical or mechanical assembly.
Risk
of injury!
■
Risk
of falling when working on the
appliance. Use a stable stepladder.
Risk
of injury!
■
Risk
of trapping body parts when opening
and closing the hinges. Keep your hands
away from the hinges.
Risk
of filter
injury!
■
The
cover may swing out. Always open
and close the filter cover slowly. Ensure that
the filter cover does not swing out after it is
released.
■
en
: Warning – Risk of electric shock!
Components inside the appliance may have
sharp edges. These may damage the
connecting cable. Do not kink or pinch the
connecting cable during installation.
Risk
of electric
shock!
■
It must
always
be possible to disconnect
the appliance from the electricity supply.
The appliance must only be connected to a
protective contact socket that has been
correctly installed.
The mains plug of the mains power cable
must be easily accessible after installation
of the appliance. If this is not possible, an
all-pole isolating switch must be integrated
into the permanent electrical installation
according to the conditions of overvoltage
category III and according to the installation
regulations.
The permanent electrical installation must
only be wired by a professional electrician.
We recommend installing a residual-current
circuit breaker (RCCB) in the appliance's
power supply circuit.
Risk
of electric
shock!are dangerous. Repairs
■
Incorrect
repairs
may only be carried out and damaged
power cables replaced by one of our
trained after-sales technicians. If the
appliance is defective, unplug the appliance
from the mains or switch off the circuit
breaker in the fuse box. Contact the aftersales service.
■
: Warning – Danger of suffocation!
Packaging material is dangerous to children.
Never allow children to play with packaging
material.
19
en
General information
KGeneral information
The surfaces of the appliance are easily damaged.
Avoid damaging them during installation.
Gener al i nf or mat i on
Exhaust duct
Note: The appliance manufacturer does not assume
any warranty for complaints attributable to the pipe
section.
■
■
■
The appliance achieves its optimum performance by
means of a short, straight exhaust air pipe and as
large a pipe diameter as possible.
As a result of long rough exhaust air pipes, many
pipe bends or pipe diameters that are smaller than
150 mm, the optimum extraction performance is not
achieved and fan noise is increased.
The pipes or hoses for laying the exhaust air line
must consist of non-combustible material.
Risk of damage from returning condensate. Install the
exhaust duct in such a way that it falls away from the
appliance slightly (1° slope).
Round pipes
An inner diameter of 150 mm is recommended.
Flat ducts
The inner cross-section must correspond to the
diameter of the round pipes.
dia. 150 mm ca. 177 cm2
■
■
20
Flat ducts should have no sharp bends.
Use sealing strips for different pipe diameters.
Electrical connection
: Warning – Risk of electric shock!
It must always be possible to disconnect the appliance
from the electricity supply. The appliance must only be
connected to a protective contact socket that has been
correctly installed.
The mains plug of the mains power cable must be
easily accessible after installation of the appliance. If
this is not possible, an all-pole isolating switch must be
integrated into the permanent electrical installation
according to the conditions of overvoltage category III
and according to the installation regulations.
The permanent electrical installation must only be wired
by a professional electrician. We recommend installing
a residual-current circuit breaker (RCCB) in the
appliance's power supply circuit.
: Warning – Risk of electric shock!
Components inside the appliance may have sharp
edges. These may damage the connecting cable. Do
not kink or pinch the connecting cable during
installation.
The required connection information can be found on
the rating plate inside the appliance; to access it, you
will need to remove the activated charcoal filter.
Length of the cable: approx. 1.30 m
This appliance complies with the EC interference
suppression regulations.
The appliance must be disconnected from the power
supply whenever installation work is being carried out.
Installation
Installing the appliance
5Installation
I n s t a l a t i on
: Warning – Risk of injury!
Components inside the appliance may have sharp
edges. Wear protective gloves.
Preparing for installation
■
■
■
en
We recommend a distance of at least 700 mm and a
maximum of 1300 mm. The cooking vapours are
more difficult to draw in the further away they are
from the hob.
So that cooking vapours are optimally drawn in,
install the extractor hood in the middle of the hob.
The installation site must be easily accessible, so
that the appliance can be accessed freely for
servicing.
: Warning – Risk of injury!
Risk of trapping body parts when opening and closing
the hinges. Keep your hands away from the hinges.
1. Tilt the transport lock slightly upwards and carefully
pull it upwards and out at an angle.
Checking the ceiling
■
■
The ceiling must be flat, horizontal and adequately
load-bearing.
The max. weight of the appliance is 40 kg.
Notes
■
Check the cut-out area for existing cables of other
appliances.
■
When mounting the extractor hood, a suitable
substructure is required that is securely fastened to
the concrete ceiling.
■
Do not fit the appliance directly onto plasterboard (or
similar lightweight materials) in a suspended ceiling.
■
To ensure correct installation, you must use a
material which is sufficiently stable and suitable for
both the structural conditions and the weight of the
appliance.
2. Remove residues from polystyrene from the interior
of the appliance.
3. Remove the grease filter.
4. Fully insert the appliance into the cut-out until you
hear the mounting brackets engage.
Preparing the ceiling
The ceiling must still be sturdy after the cut-outs have
been made.
1. Cover the hob to protect it from damage.
2. Make the cut-out in the ceiling.
]
[
[
“
“
\
\
]
“ ²
“ ²
3. After making the cut-outs, remove any shavings.
21
Installation
en
5. Carefully screw in diagonally opposite screws.
Note: Tighten the screws one at a time so that the
appliance is not wedged in the cut-out.
4. Turn the fan box into the correct position according
to the installation situation.
5. Push the fan box to the side and connect the power
supply.
6. Carefully tighten screws in succession until the
appliance is flush-mounted on the ceiling.
Note: Do not overtighten the screws to ensure that
the appliance is not damaged.
Connecting the appliance
1. Press together the cable duct at the sides and
remove it.
6. Push the fan box to the other side and connect the
ducting.
7. Position the fan box in the centre and screw it firmly
in place.
8. Connect the cable.
2. Disconnect the cable at the appropriate point.
3. Undo the opposite screws to loosen the fan box.
7
9. Press together the cable duct at the sides, attach
and click into place.
22
Installation
Fitting the filter cover
Removing the appliance
: Warning – Risk of injury!
: Warning – Risk of injury!
: Warning – Risk of injury!
: Warning – Risk of injury!
1. Open the hinges on the filter cover.
2. Mount the filter cover on the designated screws and
1.
2.
3.
4.
Components inside the appliance may have sharp
edges. Wear protective gloves.
Risk of trapping body parts when opening and closing
the hinges. Keep your hands away from the hinges.
push it backwards/forwards depending on the key
hole opening into the narrow section.
3. Tighten the fastening screws of the hinges.
en
Components inside the appliance may have sharp
edges. Wear protective gloves.
Risk of trapping body parts when opening and closing
the hinges. Keep your hands away from the hinges.
Disconnect the appliance from the power supply.
Swing down the filter cover.
Remove the metal grease filters.
Press together the cable duct at the sides and
remove it.
5. Undo the screws on the hinges up to approx. 7 mm.
Note: Do not loosen them fully.
6. Unhook and remove the filter cover.
7. Loosen the screws on the fan box, remove the
ducting and pull out the mains plug. Then screw the
fan box firmly back in place.
8. Push the removal slide inwards to loosen the
mounting brackets.
4. Insert the metal grease filter.
5. Swing the filter cover up and ensure that it engages.
9. Release the appliance slowly at an angle.
23
%6++DXVJHUlWH*PE+
&DUO:HU\6WU0QFKHQ
*(50$1<
VLHPHQVKRPHEVKJURXSFRP
0DQXIDFWXUHGE\%6++DXVJHUlWH*PE+XQGHU7UDGHPDUN/LFHQVHRI6LHPHQV$*
*9001369477*
9001369477
980613
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising