Siemens | LU93LCC20 | Instruction manual | Siemens iQ300 Built-under cooker hood Instruction manual

Siemens iQ300 Built-under cooker hood Instruction manual
Extractor hood
LU63LCC20, LU63LCC40, LU63LCC50, LU93LCC20
siemens-home.bsh-group.com/welcome
siemens-home.com/welcome
[en] Instruction manual
Register
your
product
online
Ú Table of contents
e[nuoIrs]ctimanul
Important safety information.....................................................3
Environmental protection ..........................................................5
Saving energy......................................................................................5
Environmentally-friendly disposal.....................................................5
Operating modes........................................................................5
Exhaust air mode ................................................................................5
Circulating-air mode ...........................................................................5
Operating the appliance ............................................................6
Setting the fan .....................................................................................6
Lighting .................................................................................................6
Cleaning and maintenance ........................................................6
Trouble shooting ........................................................................ 8
Fault table.............................................................................................8
After-sales service ..................................................................... 8
Accessories ................................................................................ 9
Produktinfo
Additional
information on
on products,
products, accessories,
accessories, replacement
replacement
Additional information
parts and
and services
services can
can be
be found
found at
at www.siemens-home.bshwww.siemens-home.com
parts
group.com
and in shop
the online
shop www.siemens-home.bshand in the online
www.siemens-eshop.com
group.com/eshops
: Important safety information
Read these instructions carefully. Only then
will you be able to operate your appliance
safely and correctly. Retain the instruction
manual and installation instructions for
future use or for subsequent owners.
The appliance can only be used safely if it
is correctly installed according to the safety
instructions. The installer is responsible for
ensuring that the appliance works perfectly
at its installation location.
This appliance is intended for domestic use
and the household environment only. The
appliance is not intended for use outside.
Do not leave the appliance unattended
during operation. The manufacturer is not
liable for damage which is caused by
improper use or incorrect operation.
This appliance is intended for use up to a
maximum height of 2000 metres above sea
level.
This appliance is not intended for use by
persons (including children) with reduced
physical, sensory or mental capabilities, or
lack of experience and knowledge, unless
they have been given supervision or
instruction concerning use of the appliance
by a person responsible for their safety.
Children must not play with, on, or around
the appliance. Children must not clean the
appliance or carry out general maintenance
unless they are at least 8 years old and are
being supervised.
Keep children below the age of 8 years old
at a safe distance from the appliance and
power cable.
Check the appliance for damage after
unpacking it. Do not connect the appliance
if it has been damaged in transport.
This appliance is not intended for operation
with an external clock timer or a remote
control.
Danger of suffocation!
Packaging material is dangerous to
children. Never allow children to play with
packaging material.
Danger of death!
Risk of poisoning from flue gases that are
drawn back in.
Always ensure adequate fresh air in the
room if the appliance is being operated in
exhaust air mode at the same time as room
air-dependent heat-producing appliance is
being operated.
Room air-dependent heat-producing
appliances (e.g. gas, oil, wood or coaloperated heaters, continuous flow heaters
or water heaters) obtain combustion air
from the room in which they are installed
and discharge the exhaust gases into the
open air through an exhaust gas system
(e.g. a chimney).
In combination with an activated vapour
extractor hood, room air is extracted from
the kitchen and neighbouring rooms - a
partial vacuum is produced if not enough
fresh air is supplied. Toxic gases from the
chimney or the extraction shaft are sucked
back into the living space.
■ Adequate incoming air must therefore
always be ensured.
■ An incoming/exhaust air wall box alone
will not ensure compliance with the limit.
3
Safe operation is possible only when the
partial vacuum in the place where the heatproducing appliance is installed does not
exceed 4 Pa (0.04 mbar). This can be
achieved when the air needed for
combustion is able to enter through
openings that cannot be sealed, for
example in doors, windows, incoming/
exhaust air wall boxes or by other technical
means.
In any case, consult your responsible
Master Chimney Sweep. He is able to
assess the house's entire ventilation setup
and will suggest the suitable ventilation
measures to you.
Unrestricted operation is possible if the
vapour extractor hood is operated
exclusively in the circulating-air mode.
Risk of fire!
■ Grease deposits in the grease filter may
catch fire.
Clean the grease filter at least every
2 months.
Never operate the appliance without the
grease filter.
■ Grease deposits in the grease filter may
catch fire. Never work with naked flames
close to the appliance (e.g. flambéing). Do
not install the appliance near a heatproducing appliance for solid fuel (e.g.
wood or coal) unless a closed, nonremovable cover is available. There must
be no flying sparks.
■ Hot oil and fat can ignite very quickly.
Never leave hot fat or oil unattended.
Never use water to put out burning oil or
fat. Switch off the hotplate. Extinguish
flames carefully using a lid, fire blanket or
something similar.
■ When gas burners are in operation without
any cookware placed on them, they can
build up a lot of heat. A ventilation
appliance installed above the cooker may
become damaged or catch fire. Only
operate the gas burners with cookware on
them.
Risk of fire!
Risk of fire!
Risk of fire!
Operating several gas burners at the
same time gives rise to a great deal of
heat. A ventilation appliance installed
above the cooker may become damaged
or catch fire. Never operate two gas
burners simultaneously on the highest
flame for longer than 15 minutes. One
large burner of more than 5 kW (wok) is
equivalent to the power of two gas
burners.
Risk of burns!
The accessible parts become very hot when
in operation. Never touch hot parts. Keep
children at a safe distance.
Risk of injury!
■ Components inside the appliance may
have sharp edges. Wear protective gloves.
■ Items placed on the appliance may fall
down. Do not place any objects on the
appliance.
■ The light emitted by LED lights is very
dazzling, and can damage the eyes (risk
group 1). Do not look directly into the
switched on LED lights for longer than
100 seconds.
Risk of electric shock!
■ A defective appliance may cause electric
shock. Never switch on a defective
appliance. Unplug the appliance from the
mains or switch off the circuit breaker in
the fuse box. Contact the after-sales
service.
■ Incorrect repairs are dangerous. Repairs
may only be carried out and damaged
power cables replaced by one of our
trained after-sales technicians. If the
appliance is defective, unplug the
appliance from the mains or switch off the
circuit breaker in the fuse box. Contact the
after-sales service.
■ Do not use any high-pressure cleaners or
steam cleaners, which can result in an
electric shock.
■
Risk of injury!
Risk of injury!
Risk of electric shock!
Risk of electric shock!
Causes of damage
Caution!
Risk of damage due to corrosion. Always switch on the
appliance while cooking to avoid condensation. Condensate
can produce corrosion damage.
Risk of damage due to ingress of humidity into the electronic
circuitry. Never clean operator controls with a wet cloth.
Surface damage due to incorrect cleaning. Clean stainless
steel surfaces in the direction of the grain only. Do not use any
stainless steel cleaners for operator controls.
Surface damage due to strong or abrasive cleaning agents.
Never use strong and abrasive cleaning agents.
Risk of fire!
Risk of damage from returning condensate. Install the exhaust
duct in such a way that it falls away from the appliance slightly
(1° slope).
4
Environmental protection
Your new appliance is particularly energy-efficient. Here you
can find tips on how to save even more energy when using the
appliance, and how to dispose of your appliance properly.
Saving energy
■
■
■
During cooking, ensure that there is a sufficient supply of air
so that the extractor hood can work efficiently and with a low
level of operating noise.
Adjust the fan speed to the intensity of the cooking fumes.
Only use intensive mode where this is required. A lower fan
speed means that less energy is consumed.
Dispose of packaging in an environmentally-friendly manner.
This appliance is labelled in accordance with
European Directive 2012/19/EU concerning used
electrical and electronic appliances (waste
electrical and electronic equipment - WEEE). The
guideline determines the framework for the return
and recycling of used appliances as applicable
throughout the EU.
If there are intensive cooking fumes, select a higher fan
speed in good time. If cooking fumes have already spread in
the kitchen, the extractor hood must be operated for longer.
■
Switch off the extractor hood if you no longer require it.
■
Switch off the lighting if you no longer require it.
■
Environmentally-friendly disposal
Clean and, if required, replace the filter at regular intervals in
order to increase the effectiveness of the ventilation system
and to prevent the risk of fire.
Operating modes
This appliance can be used in exhaust-air mode or circulatingair mode.
Exhaust air mode
Circulating-air mode
The air which is drawn in is cleaned by the
grease filters and an activated carbon filter and
conveyed back into the kitchen.
The air which is drawn in is cleaned by the
grease filters and conveyed to the exterior
by a pipe system.
Note: The air must not be discharged into a flue that is used for
exhausting fumes from appliances burning gas or other fuels
(not applicable to appliances that only discharge the air back
into the room).
■
■
Note: To bind odours in circulating-air mode, you must install
an activated carbon filter. The different options for operating the
appliance in circulating-air mode can be found in the brochure.
Alternatively, ask your dealer. The required accessories are
available from specialist outlets, from customer service or from
the Online Shop. The accessory numbers can be found at the
end of the instructions for use.
Before conveying the exhaust air into a non-functioning
smoke or exhaust gas flue, obtain the consent of the heating
engineer responsible.
If the exhaust air is conveyed through the outer wall, a
telescopic wall box should be used.
5
Operating the appliance
These instructions apply to several appliance variants. It is
possible that individual features are described which do not
apply to your appliance.
Note: Switch on the extractor hood when you start cooking and
switch it off again several minutes after you have finished
cooking. This is the most effective way of removing the kitchen
fumes.
Note: Fold the glass cover forwards. This increases the
extraction area.
Control panel
Setting the fan
Note: Always adjust the fan strength to meet current conditions.
If there is a large build-up of steam or fumes, select a high fan
setting.
Switching on
1. Press the a1 button.
Note: If the fan is switched on, an LED lights up.
The fan starts up at the speed to which it was last set.
2. Press the 2 or 3 button to set another fan speed.
Switching off
Press the a button.
Lighting
Explanation
‚1 Switches the fan on/off
2
Switches on fan speed 2
3
Switches on fan speed 3
=
Switches the lighting on/off
The lighting can be switched on and off independently of the
ventilation.
Press the = button.
Cleaning and maintenance
: Risk of burns!
The appliance becomes hot during operation. Allow the
appliance to cool down before cleaning.
Area
Cleaning agent
Stainless steel
Hot soapy water:
Clean with a dish cloth and then dry
with a soft cloth.
: Risk of electric shock!
Clean stainless steel surfaces in the
grind direction only.
Penetrating moisture may result in an electric shock. Clean the
appliance using a damp cloth only. Before cleaning, pull out the
mains plug or switch off the circuit breaker in the fuse box.
Special stainless steel cleaning products are available from our after-sales
service or from specialist retailers.
Apply a very thin layer of the cleaning
product with a soft cloth.
: Risk of electric shock!
Do not use any high-pressure cleaners or steam cleaners,
which can result in an electric shock.
: Risk of injury!
Painted surfaces
Components inside the appliance may have sharp edges. Wear
protective gloves.
Cleaning agents
To ensure that the different surfaces are not damaged by using
the wrong cleaning agent, observe the information in the table.
Do not use any of the following:
■
Harsh or abrasive cleaning agents,
■
Cleaning agents with a high alcohol content,
■
Hard scouring pads or cleaning sponges,
■
High-pressure cleaners or steam cleaners.
Wash new sponge cloths thoroughly before use.
Follow all instructions and warnings included with the cleaning
agents.
6
Hot soapy water:
Clean using a damp dish cloth and dry
with a soft cloth/towel.
Do not use any stainless steel cleaners.
Aluminium and plas- Glass cleaner:
tic
Clean with a soft cloth.
Glass
Glass cleaner:
Clean with a soft cloth. Do not use a
glass scraper.
Controls
Hot soapy water:
Clean using a damp dish cloth and dry
with a soft cloth/towel.
Risk of electric shock caused by penetrating moisture.
Risk of damage to the electronics from
penetrating moisture. Never clean
operating controls with a wet cloth.
Do not use any stainless steel cleaners.
Cleaning the metal mesh grease filters
Installing the metal mesh grease filter
These instructions apply to several appliance variants. It is
possible that individual features are described which do not
apply to your appliance.
1. Insert the metal mesh grease filter.
: Risk of fire!
2. Fold the metal mesh grease filter upwards, locking it in place.
Grease deposits in the grease filter may catch fire.
Clean the grease filter at least every 2 months.
Never operate the appliance without the grease filter.
Changing the activated charcoal filter (only in
circulating-air mode)
Notes
■ Do not use any aggressive, acidic or alkaline cleaning
agents.
■
■
When cleaning the metal mesh grease filters, also clean the
holder for the metal mesh grease filters in the appliance
using a damp cloth.
The metal mesh grease filters can be cleaned in the
dishwasher or by hand.
By hand:
Note: You can use a special grease solvent for stubborn dirt. It
can be ordered via the Online Shop.
■
Soak the metal mesh grease filters in a hot soapy solution.
■
Clean the filters with a brush and then rinse them thoroughly.
■
Leave the metal mesh grease filters to drain.
While doing this, place the other hand under the metal mesh
grease filter.
In order to guarantee efficient odour filtration, the filter must be
serviced regularly.
The activated charcoal filters must be replaced at least every
4 months.
Notes
■ The activated charcoal filters are not included in the delivery.
The activated charcoal filters can be obtained from specialist
retailers, from our after-sales service or from the Online Shop.
■
The activated charcoal filters cannot be cleaned or
reactivated.
Note: Only use genuine replacement filters. This ensures
optimal performance of the appliance.
1. Remove the metal grease filter, see the chapter Removing
the metal grease filter.
2. Undo the threaded joint on the activated charcoal filter cover.
In the dishwasher:
Note: If the metal mesh grease filters are cleaned in the
dishwasher, slight discolouration may occur. This has no effect
on the function of the metal mesh grease filters.
■
■
Do not clean heavily soiled metal mesh grease filters together
with utensils.
Place the metal mesh grease filters loosely in the dishwasher.
The metal mesh grease filters must not be wedged in.
Removing metal grease filter
1. Push the lock and then push the metal grease filter back and
pull it down.
While doing this, place your other hand under the metal
grease filter.
3. Remove the activated charcoal filter.
Note: To avoid causing damage, do not bend the metal
grease filter.
6. Install the metal grease filter, see the chapter Installing the
4. Insert the activated charcoal filter.
5. Screw the cover in place.
metal grease filter.
2. Take the metal grease filter out of the holder.
Note: Grease may accumulate in the bottom of the metal
grease filter. Hold the metal grease filter level to prevent
grease from dripping out.
3. After removing the metal grease filters, clean the inside of the
appliance.
4. Clean the metal grease filters and let them dry before re-
fitting them.
7
Trouble shooting
Malfunctions often have simple explanations. Please read the
following notes before calling the after-sales service.
: Risk of electric shock!
Incorrect repairs are dangerous. Repairs may only be carried
out and damaged power cables replaced by one of our trained
after-sales technicians. If the appliance is defective, unplug the
appliance from the mains or switch off the circuit breaker in the
fuse box. Contact the after-sales service.
Fault table
Problem
Possible cause Solution
The appliance
does not work
The plug is not Connect the appliance to
plugged into the the power supply
mains
The lighting
does not work.
Power cut
Check whether other
kitchen appliances are
working
The fuse is
faulty
Check in the fuse box to
make sure that the fuse for
the appliance is in working
order
The LED lights
are defective.
You can read about this in
the section entitled "Replacing the LED lights".
Replacing the LED lights
: Risk of electric shock!
When changing the bulbs, the bulb socket contacts are live.
Before changing the bulb, unplug the appliance from the mains
or switch off the circuit breaker in the fuse box.
: Risk of injury!
The light emitted by LED lights is very dazzling, and can
damage the eyes (risk group 1). Do not look directly into the
switched on LED lights for longer than 100 seconds.
Important! Only use bulbs of the same type and wattage.
'5%%)(
1. Lift the bulb cover slightly and move it towards the outside of
the appliance.
2. Unscrew the bulb and replace it with a bulb of the same type.
--------
3. Fit the bulb cover.
4. Plug in the mains plug and switch the fuse back on.
After-sales service
Our after-sales service is there for you if your appliance needs
to be repaired. We will always find the right solution in order to
avoid unnecessary visits from a service technician.
When calling us, please give the product number (E no.) and
the production number (FD no.) so that we can provide you with
the correct advice. The rating plate with these numbers can be
found inside the appliance (remove the metal mesh grease
filter to gain access).
You can make a note of the numbers of your appliance and the
telephone number of the after-sales service in the space below
to save time should it be required.
E no.
FD no.
After-sales serviceO
Please be aware that a visit by an after-sales engineer will be
charged if a problem turns out to be the result of operator error,
even during the warranty period.
Please find the contact data of all countries in the enclosed
customer service list.
8
To book an engineer visit and product advice
GB
0344 892 8999
Calls charged at local or mobile rate.
IE
01450 2655
0.03 € per minute at peak. Off peak 0.0088 € per
minute.
Rely on the professionalism of the manufacturer. You can
therefore be sure that the repair is carried out by trained service
technicians who carry original spare parts for your appliances.
Accessories
(not included in the scope of delivery)
Activated charcoal filter
LZ27001
--------
9
BSH Hausgeräte GmbH
Carl-Wery-Straße 34, 81739 München, GERMANY
siemens-home.com
siemens-home.bsh-group.com
0DQXIDFWXUHGE\%6++DXVJHUlWH*PE+XQGHU7UDGHPDUN/LFHQVHRI6LHPHQV$*
*9001208184*
9001208184
960501
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising