Siemens | CI30RP01 | Installation instructions | Siemens iQ700 Built-in Fridge Installation instructions

Siemens iQ700 Built-in Fridge Installation instructions
en Installation instruction
CI24R..
CI30R..
FI18N..
FI24N..
FI24D..
CI24W..
Built-in appliance
q~ÄäÉ=çÑ=`çåíÉåí
Safety and warning information .........................
4
Installation possibilities ......................................
5
Stand alone appliance ..............................................
5
Side-by-Side set up ...................................................
5
Stand alone appliance with dividing wall ..............
5
Stand alone appliance as an end section
to a row of kitchen units ...........................................
5
Installing the appliance .......................................
6
Installation location ....................................................
6
Atmosphere grades ..................................................
6
Stable installation ......................................................
6
Installation niche ........................................................
6
Neighbouring kitchen furniture ................................
6
Subsurface ..................................................................
7
Aligning the appliance ..............................................
7
Electrical connection ...........................................
7
Water connection .................................................
7
Dimensions of the installation niche .................
8
Tools and accessories which are needed .........
1.
Adjusting the appliance
in the niche .......................................... 15
2.
Fastening the appliance
to the niche ceiling ............................. 15
3.
Fastening the appliance to the side
wall of the installation niche .............. 16
4.
Checking that the finger guard
moves easily ........................................ 16
1.
Fastening the plinth strip ................... 18
2.
Aligning the base cover .................... 18
3.
Switching the appliance
on for the first time ............................. 19
4.
Preparing the furniture doors ........... 19
5.
Loading the appliance door ............. 19
6.
Removing positioning aids ............... 19
7.
Fastening the adjusting rib
to the furniture door ........................... 20
8.
Fastening the fixing rib
to the furniture door ........................... 20
9.
Mounting the furniture door .............. 21
10. Screw on the lower fixing angle ...... 22
1.
Fasten the finger protector ............... 23
9
2.
Attaching the covers .......................... 23
Scope of delivery .......................................................
9
3.
Tensioning the hinge springs ........... 24
Additional accessories .............................................
9
Miscellaneous ............................................................
9
Changing over the door hinges .............. 25
Tools ............................................................................
9
Removing/changing the sealing mat ..... 27
Installation manual .............................................. 10
Side-by-Side set up .................................... 28
Special installation steps ...................................
25
1.
Check the installation niche ............. 10
Preparing the water connection .............. 30
2.
Removing the packaging .................. 10
3.
Transporting the appliance ............... 11
Connecting the appliance
to the water supply .................................... 30
4.
Installation preparation ...................... 11
Aligning ice and water dispenser ............ 31
5.
Special installation steps ................... 11
Attaching covering strips .......................... 32
1.
Attaching the anti-tipping brackets
to the wall ............................................. 12
Setting the door opening angle ............... 33
2.
Attaching alternative anti-tilt
device ................................................... 13
3.
Attaching the edge protectors ......... 13
4.
Attaching the fastening
sheets (lateral)...................................... 13
5.
Sliding the appliance into the
installation niche ................................. 14
P
Safety and warning information
These mounting instructions are designed to help you
install your new appliance.
The manufacturer cannot be held liable for mounting
which has been improperly carried out. We recommend
that you allow a qualified specialist to set up and switch
the appliance on for the first time.
Following all information and keeping to the instructions
are preconditions for mounting and switching the
appliance on safely for the first time.
Keep the mounting instructions safe for use later on.
Before setting up and switching the appliance on for the
first time, read the mounting instructions fully and
thoroughly.
ã Warning
The appliances are very heavy and must be
secured from tipping when transporting, when
mounting and when operating. It is absolutely
necessary to fit an anti-tip device.
Keep the doors closed until the appliance has been
mounted completely and secured according to the
instructions in these mounting instructions.
Because of the weight / dimensions of the
appliance and to minimise the risk of injuries and
damage to the appliance at least two persons are
necessary to set-up the appliance securely.
Use the appliances according to the prescribed
application.
Pull out the plug or remove the fuse before
commencing work on the appliance.
Only customer service may change the power cord
and carry out any other repairs. Improper
installations and repairs may put the user at
considerable risk.
Apart from statutory national regulations, you
should stick to the connection terms relating to the
local electricity and water companies.
Q
ã Caution
Setting up and mounting this appliance requires
extensive expertise in various trades (mechanics,
carpentry, plumbing, electrics).
It is the duty of the person setting the appliance up
to guarantee that it is set up and commissioned
securely.
Mistakes in setting the appliance up and damage
resulting from this do not come under the warranty
of the manufacturer. Terms of guarantee are found
in the operating instructions of the appliances.
Installation Possibilities
Various installation possibilities are available.
These are only limited by the kitchen design and the
finger protector function.
Stand alone appliance with dividing
wall
Stand alone appliance
Side-by-Side set up



When measuring the dividing wall for model 4, pay
attention to the thickness of the furniture front to be
mounted in order to avoid damage when opening
doors at the same time.
If the distance between the appliances is less than
160 mm, the auxiliary side heater must be used.
For further information see section “Tools and
Accessories which are needed”.
The minimum thickness of the dividing walls
is 16 mm.
Stand alone appliance as an end
section to a row of kitchen units
If a side of the appliance is visible, use a side covering.
The side covering must be connected firmly to the wall,
the floor and the upper cupboards before the appliance
is slid into the installation niche.
The dimensions of the side covering are governed by
the opposing niche wall. During installation, make sure
that the installation niche has right angles and has the
exact size necessary for the appliance.
R
Installing the appliance
Installation location
Stable installation
ã
The appliance is very heavy and has a tendency to tilt
forwards when the appliance door is opened.
The appliance must not be switched on until there
is no possibility of the appliance tilting over.
Caution:
The appliance is very heavy. Data relating to the
weight when empty is found in the following
table:
Appliance
Weight (empty)
Refrigerator 60.3 cm
approx. 131 kg
Refrigerator 75.6 cm
approx. 145 kg
Freezer 45.1 cm *
approx. 109 kg
Freezer 60.3 cm *
approx. 131 kg
In the case of doubt, the help of architect or specialist
builder should be enlisted.
Freezer 75.6 cm *
approx. 145 kg
Installation niche
Wine storage cabinet 45.1 cm
approx. 109 kg
Wine storage cabinet 60.3 cm
approx. 131 kg
It is important to keep to the stated dimensions of the
installation niche with a view to trouble-free fitting, and
the subsequent appearance of the kitchen furniture
frontage.
* without water and ice dispenser
The appliance should be installed in a dry, well
ventilated space.
The location should not be exposed to the direct
sunlight and should not lie next to a source of heat such
as a cooker or a radiator etc. If installation next to a
source of heat cannot be avoided, either a suitable
insulating plate should be used or you should keep to
the following minimum distances:

3 cm to electric or gas cookers.

30 cm to an oil-fired or solid-fuel cooker.
The floor of the installation location must not give way;
if required, reinforce floor. To ensure that the ice maker
functions correctly, the appliance must be upright.
Atmosphere grades
The climate class can be found on the rating plate.
The climate class indicates within which ambient
temperatures the appliance can be operated.
S
The safest method of installing the appliance in a stable
position is to use the supplied anti-tilt brackets.
Climate class
Permitted ambient
temperature
SN
+10 °C to 32 °C
N
+16 °C to 32 °C
ST
+16 °C to 38 °C
T
+16 °C to 43 °C
If the installation cavity is adequately stable and the
appliance can be attached securely to the upper and
side walls of the cavity, it may be possible to dispense
with the anti-tilt brackets. A prerequisite for this is
always a firm connection between the cavity and back
wall!
Special care should be taken that the niche has right
angles. The side walls should not exhibit areas that
stick out, projections or unevenness.
You should determine the right angles of the installation
niche with appropriate means, e.g. by measuring
diagonally and by using a spirit level.
The side walls and the upper end of the installation
niche must be at least 16 mm thick.
Neighbouring kitchen furniture
The new appliance is screwed down tightly using parts
of the cabinet and the upper cabinet.
Care should therefore be taken, that all upper cabinets
to which something has been fastened are securely
connected to the subsurface or wall by appropriate
means.
The minimum thickness of the base should be
a minimum of 19 mm.
Subsurface
ã
Electrical connection
Caution:
A fully laden appliance is heavy, data relating to
the weight when empty is found in the following
table.
Appliance
Weight (laden)
Refrigerator 60.3 cm
approx. 400 kg
Refrigerator 75.6 cm
approx. 500 kg
Freezer 45.1 cm *
approx. 250 kg
Freezer 60.3 cm *
approx. 350 kg
Freezer 75.6 cm *
approx. 425 kg
Wine storage cabinet 45.1 cm
approx. 245 kg
Wine storage cabinet 60.3 cm
approx. 310 kg
The socket must be near the appliance and also freely
accessible following installation of the appliance.
The appliance complies with the protection class I.
Connect the appliance to 220–240 V/50 Hz alternating
current via a correctly installed socket with protective
conductor. The socket must be fused with a 10 to 16 A
fuse.
For appliances operated in non-European countries,
check whether the stated voltage and current type
match the values of your mains supply match the values
of the mains supply. These specifications can be found
on the rating plate.
ã
Warning:
Never connect the appliance to electronic energy
saver plugs. Our appliances can be used with
mains and sine-controlled inverters. Mainscontrolled inverters are used for photovoltaic
systems which are connected directly to the
power supply system. Sine-controlled inverters
must be used for isolated applications (e.g. on
ships or in mountain lodges) which are not
connected directly to the national grid.
* without water and ice dispenser
The subsurface must be level and even in order to
ensure that the appliance is securely installed and
works correctly.
The subsurface must be made from a hard, non-flexible
material.
The floor of the installation space must have the same
height as the rest of the space.
Water connection
On account of the weight of a fully-laden appliance, it is
necessary to have a bearing subsurface. In the case of
doubt, the help of architect or specialist builder should
be enlisted.
ã
Aligning the appliance
To ensure that the appliance functions correctly, it must
be set level with a spirit level.
If the appliance is not level, water may flow out of the
ice maker, ice cubes may be irregular or the doors may
not close properly.
Warning:
Connect the appliance to a cold water pipe only.
A cold water connection is necessary for operating the
automatic ice maker. The water pressure must lie
between 1.7 and 10 bar. The installation must
correspond to the local plumbing regulations.
A separate shut-off valve should be installed in the coldwater inflow.
The shut-off valve should not be located behind the
appliance. It is recommended that you mount the shutoff valve directly next to the appliance or at another
place which is easily accessible.
When installing the water connection, pay attention to
the permissible installation area for the water mains.
For more information concerning the permissible
installation area, see the section “Dimensions of the
installation niche”.
Note, if the water line for the cold water connection is
not included in the product package:


For connection to the drinking water mains use
only water pipes which are suitable for drinking
water. Observe national regulations and the
connection conditions of the local water supply
companies.
The maximum outside diameter of the water mains
(without connecting pieces) is 10 mm.
T
Dimensions of the installation niche
X
Y
457 mm
229 mm
610 mm
305 mm
762 mm
381 mm
Important:
The upper niche wall must consist of
a rigid, load bearing material
(minimum thickness 16 mm).
Important:
The lateral niche walls must be
completely even and free from
bumps. If the niche is formed as a
separate part, the side walls must be
completely even up to a depth of at
least 100 mm and free from bumps.
Key:
A
Area for installation of the water connection
B
Area for installation of the electric current
C
Depth of the installation niche, depending on the kitchen design
C = 610 mm minimum!
U
Tools and accessories which are needed
Scope of delivery



Tools
Installation manual
Operating instructions
Installation accessories
Rechargeable screwdriver
Additional accessories
Installation accessories for side-by-side installation
T20 Torx-bit magnetic
holder
For permanent connection of two appliances,
e.g. a freezer next to a refrigerator.
Lateral additional heating
T20 Torx screwdriver
Necessary when the distance between two appliances
is less than 160 mm.
Connecting element for furniture doors
For connecting two furniture doors (see explanation in
Section “4. Preparing the furniture doors”). It can be
used for standard height furniture doors without any
preparation work.
8 mm socket wrench
Various size drills
Miscellaneous










Step ladder
Fixed spanner SW 13 mm
Trolley, wheelbarrow or sack barrow
Hammer drill for drilling holes into the wall and floor
Various size drills for various materials
Wood plank, (min. 8 x 10 cm) as an alternative antitip device. Length should correspond to the width
of the installation niche.
Water pump pliers
Adjustable spanner
Various size wood screws
Screw (M8, at least 80 mm long), nut
Thin (1.5 mm), material suitable for protecting the
floor against damage (e.g. linoleum)
Suitable material for covering and protecting the
cabinets (e.g. protective film)
Knife with an adjustable
blade
Metal tape measure,
folding ruler
Adhesive tape
Note:
Before using, check whether the removed adhesive
tape leaves adhesive residue on the work surfaces!
Otherwise do not use on high-quality work
surfaces.
Angle of contact
60 cm and 120 cm spirit
levels
Level, min. 120 cm long
V
Installation manual
The following mounting instructions describe mounting
steps for various appliance models.
Therefore, deviations may occur from that shown in the
diagrams.
2.
Removing the packaging
ã
Warning:
 The appliance could tip over when unpacking.
 The appliance could tip over when the
Reference is made to specific mounting steps for
individual appliances.
1.
Check the installation niche
ã
Caution:
Before starting the installation, check carefully
that the installation cavity meets the requirements for a secure and trouble-free installation:
1.
Check the subsurface.
Follow the notes in the section “Installing the
appliance”.
2.
Check the dimensions of the niche.
3.
Re-examine whether the niche has right angles.
4.
Re-examine the positioning of the plug.
Additionally follow the instructions in the sections
“Electrical connection” and “Dimensions of the
installation niche”.
5.
appliance door is opened.
 The appliance is very heavy.
Risk of personal injury and damage to the
appliance!
Note:
Check the appliance for damage. Do not install the
appliance if there is visible damage. If there are queries,
please contact the dealer.
To protect the subsurface from damage whilst
installing:
1.
Place cardboard or plywood under the appliance.
2.
Remove packaging carton. Be careful when using
the knife so as not to damage the surface of the
appliance.
3.
Remove accessories from the outside of the
appliance.
Keep adhesive tape which was used to attach the
supplied accessories to the appliance. It is
used subsequently for attaching the edge
protection to the cavity walls (see Section
“A / 4. Sliding the appliance into the installation
niche”).
Check the positioning of the water connection
(for appliances with ice maker)
Additionally follow the instructions in the sections
“Water connection” and “Dimensions of the
installation niche”.
6.
Re-examine the stability and fastening of the
neighbouring cabinet parts. All cabinet parts in the
vicinity of the appliance have to be firmly
connected to the wall.
7.
Re-examine that when opening the appliance door,
it does not collide with neighbouring kitchen parts
(for door opening angle).
4.
Remove transportation protection devices (a) and
lift appliance off the pallet – appliance is very
heavy!
5.
Carefully open the appliance – risk of tipping over
– and remove accessories and installation
materials from inside the appliance. Close the door
again.
Note:
Only remove the transporting securing units with
which the slide-in bases and the storage
compartments in the appliance are protected after
completing the installation as otherwise, parts
could be damaged.
NM
3.
Transporting the appliance
4.
ã
Warning:
Unpack installation materials and accessories.
The appliance is very heavy. Handle it carefully,
as otherwise people helping to lift it could be hurt
or the appliance could be damaged.
To simplify installation, the packages are identified with
labels A, B and C corresponding with the manual
sections.
Installation preparation
The appliance has a height of 2,126 mm. If it is not
possible to support the appliance in a vertical position
because of the structure of the building, the appliance
can be transported on its side.
Note:
Never put the appliance up via its side! Risk of damage
to the appliance.
When putting the appliance up, pay attention to the
minimum height that is required at the assembly
location according to the following table.
Putting the appliance
up on via its back
side
Putting the appliance
up via its side wall
5.
Special installation steps
This symbol indicates that additional steps need to be
taken before proceeding to the next chapter.
Special installation steps are described after section D.
Minimum height
218.5 cm
Never put the appliance
up via its side!
aufrichten!
Note:
Never push means of transportation under the front of
the appliance. Risk of damage to the appliance
 Exchanging the door stops see
“Special installation steps”.
 Sealing mat, see “Removing/
changing the sealing mat”.
 Side-by-Side set up see “Side-by-
Side set up”.
 Water connection see “Preparing the
water connection“ and „Connecting
the appliance to the water supply”.
 Ice water dispenser, see “Aligning
ice and water dispenser”.
 Cover strips for the wine cooler, see
“Attaching covering strips”
 Door opening angle see “Setting the
door opening angle”.
1.
Transport the appliance with an aid to transport
which is suitable (sack barrow, trolley or
wheelbarrow).
2.
When transporting, secure the appliance from
being tipped.
NN
1.
Attaching the anti-tipping brackets
to the wall
ã
Warning:
Ensure that in the wall area there are no
electrical wires or pipes which could be
damaged by pipes. Risk of injury or damage!
ã
Warning:
When installing or working with floor anchors
always use protective glasses and other
protective equipment or protective clothing –
risk of injury!
Note:




Each appliance requires 2 anti-tilt brackets.
The set supplied, contains fastening screws for
various subsurfaces. Select the fastening screws
corresponding to the local conditions.
A total of 2 anti-tilt brackets are used for a side-byside installation.
If the anti-tilt brackets, and therefore the appliance,
cannot be securely attached with the supplied
fastening screws, another suitable method must be
used to attach the appliance securely.
The anti-tilt brackets (a) must overlap the appliance by at
least 105 mm to ensure that the appliance is stable.
If the minimum overlap cannot be observed due to
structural conditions, these can be overcome by the
attachment of a suitable device, e.g. an adequately
dimensioned beam (b) behind the brackets.
The length of the plank should correspond to the width
of the installation niche!
Important information concerning attachment with
wall plugs and screws:



NK
aÉíÉêãáåÉ=íÜÉ=Ñ~ëíÉåáåÖ=éçáåíë=çÑ=íÜÉ=~åíáJíáäí=êáÄëK=
Determine the actual dimensions according to the
section “Dimensions of the installation niche”.
2.
NO
Screw on the anti-tilt brackets tightly. Re-examine to
make sure that the screws are firmly tightened.
Not suitable for use in light-weight masonry such as
hollow blocks or tiles!
Never use in fresh concrete which has not yet
hardened.
Do not use spiral-flute counterbores
(countersinking tool) to drill the holes.
2.
Attaching alternative anti-tilt
device
Important note:
If the anti-tilt brackets cannot be securely attached,
a wooden beam can be used above the appliance as
an alternative anti-tilt device. Care should be taken that
there is not a gap between the appliance and the
wooden beam. As far as possible, always screw the
wooden plank to the rear wall of the niche.
1.
3.
Attaching the edge protectors
To protect the edges of the installation cavity, it is
recommended to attach edge protection made of
a suitable material.
Attach the edge protection with the adhesive tape which
was used to attach the accessories to the appliance
Cut the wooden plank to the required length (cross
section min. 8 x 10 cm). The length should
correspond to the width of the installation niche!
Note:
 If the installation niche is deeper than the
appliance, select a stronger beam or use two,
one behind the other.
 The plank must overlap the appliance by at least
50 mm.
4.
Attaching the fastening sheets
(lateral)
Attach the fastening sheets (lateral) to the appliance.
2.
Mark the installation height (underside edge of the
plank) on the rear wall of the niche.
3.
Select the screws according to the thickness of the
wooden plank: Length min. 2.5 x wood thickness,
diameter 12 or 14 mm.
Note:
Select the number of screws corresponding to the
niche width so that you ensure that the plank can
be securely mounted.
According to the subsurface:
4.
Look for the supports on the rear wall of the niche
and mark the drill holes on the plank
corresponding to the position of the support.
or
5.
Fasten suitable dowel into the rear wall.
6.
Pre-drill.
7.
Screw the plank onto the rear wall of the niche.
These are special installation steps.
Instructions are provided after
section D.
 Exchanging the door stops see
“Special installation steps”.
 Sealing mat, see “Removing/
changing the sealing mat”.
 Side-by-Side set up see “Side-by-
Side set up”.
 Water connection see “Preparing the
water connection”.
NP
5.
Sliding the appliance into the installation niche
ã
Caution:
5.
Be careful when sliding the appliance into the
installation niche. Do not damage the water
connection or power cord.
Protect the mains lead from getting wedged under
or behind the appliance.
Recommended procedure:
Tie a piece of string in the middle of the power cord
and guide the string forwards over the appliance.
When pushing the appliance into the cavity, pull the
cable upwards with the string.
Note:
If the floor or appliance is skew in relation to the
installation niche, the height-adjustable wheels should
be correspondingly adjusted before sliding the
appliance into the niche.
or
Fasten the mains lead onto the floor with adhesive
tape, in the middle behind the appliance approx.
38 cm from the rear of the niche.
1.
Remove the base panelling.
2.
Unscrew the height-adjustable feet at the back of
the appliance by approx. 10 mm.
6.
Slide the appliance carefully into the niche.
3.
Plug the mains plug into the socket.
7.
4.
Insert water connection line into the protective pipe
on the rear of the appliance.
Remove edge protection from the installation cavity
(if previously attached).
ã
Warning:
The appliance may tilt when the water
connection line is inserted into the protective
pipe (a)!
NQ
1.
Adjusting the appliance in the
niche
2.
Unscrew the height-adjustable feet at the front of
the appliance until the mark on the base has
reached the indicated height (32 mm).
3.
Align the appliance vertically using the feet at the
back. Use spirit level.
Note:




To ensure that the appliance functions correctly,
it must be set level with a spirit level.
Do not tip the appliance in the niche! When
screwing down the height adjustable feet, proceed
step by step. Lower by alternating left to right.
The rear feet can be set easier when the appliance
is not loaded on the rear.
When using a wooden plank as an alternative antitilt mechanism of these mounting instructions, turn
the appliance as far as it will go against the wooden
plank. Do not bend against the wooden plank.
The positioning supports are set out for the following
overall strengths of the furniture doors to be mounted.


19 mm
38 mm
Re-examine the actual thickness of the doors to be
mounted in order where necessary, to be able to
compensate possible digressions.
1.
Adjust the appliance to the existing furniture.
Keep the straight edge on the door, above the
positioning supports.
2.
Fastening the appliance to the
niche ceiling
Note:
It is essential to attach the appliance to the ceiling of the
cavity.
1.
Screw on the front bars of the fastening sheets
(above) with the upper cabinets.
2.
If there is a large crack available above the
appliance, integrate a wooden plank above the
appliance and pay attention that the crack is
completely filled.
The height-adjustable feet on the front and rear can all
be adjusted from the front.
Front:
with a fixed spanner SW 13 mm
Rear:
with a 8 mm socket spanner with flexible
shaft. Use cordless screwdriver.
A mark (a) is made on the base of the appliance which
serves as a standard measurement for setting the
height. When setting the height, raise the mark to
32 mm above the ground. This dimension is very
important for the subsequent adjustment of the cabinet
frontage.
The assembly gauge (b) is used to set
this height correctly. The upper edge of
the gauge must be in alignment with the
mark on the appliance.
NR
3.
If there enough room on the top of the appliance fix
the the lateral bars of the fastening sheets (above)
to the side of the niche.
3.
Fastening the appliance to the side
wall of the installation niche
Screw on the bars of the fastening sheets (lateral)
with the cabinet parts located next to them.
4.
Cut the connection ribs (a) to the desired height!
5.
Press connection ribs (a) into the covering ribs.
6.
Attach the covering ribs (b) onto the fastening
sheets (above),
Note:
In the case of a Side-by-Side installation this installation
step is not possible. These parts have been removed.
4.
Checking that the finger guard
moves easily
It is now essential to check that the finger guard moves
easily. At a later time any required corrections will be
more difficult.
Note:


1.
Note:
If the installation is side-by-side, connect the cover rails
of both appliances using the bolt from the installation
accessories for side-by-side installation.
NS
The supplied finger protector can be used for both
sides of the hinges.
Because of different installation possibilities, the
finger protector has to be shortened to the required
length.
Shorten the finger protector at the upper side
above the covering strip by 55 mm (NK).
2.
Push the cut-off remnant on the hinge side into the
gap between the appliance and cavity wall.
The part must be easy to push in and pull out (OK)!
These is a special installation step.
Instructions are provided after
section D.
 Water connection see “Connecting
the appliance to the water supply”.
3.
Ensure smooth running at all positions of the
door (PK).
NT
1.
Fastening the plinth strip
Note:
Never cover the ventilation cracks in the base panelling.
Risk of damage to the appliance.
2.
1.
Place base cover on the appliance (do not screw
on).
2.
Measure the difference in depth A between the
base panelling and the base strip of the adjacent
lower cabinets.
3.
Remove the base panelling again.
4.
Adjust the brackets (a) to the dimensions A and
tighten.
5.
Fasten the base panelling.
Nominal dimensions to be observed:
1.
Where necessary, cut the base strip to the required
length.
2.
Place base cover on the appliance (do not screw
on).
3.
Take the protective film off from the adhesive pads
on the Velcro strip.
4.
Put the base strip onto the base panelling and push
firmly.
5.
Base strip can be screwed to the base cover from
behind. There are holes in the base cover for this
purpose.
NU
Aligning the base cover
3.
Switching the appliance on for the
first time
The appliance should now be switched on for the first
time in order to ensure the accuracy of the following
mounting steps and with it, the appearance of the entire
kitchen frontage.
1.
Open the appliance door.
2.
Actuate the appliance’s On/Off button.
5.
Loading the appliance door
When attaching the furniture doors it is recommended
to load the storage sections in the door with weights in
order to ensure that the when adjusting crack
dimensions turn out to be as precise as possible.
Loading recommendations:
Appliance width
Loading of the appliance door
Only for appliances with a water connection:
45.1 cm
10 kg
In the case of possible damage of the water mains,
keep the shut-off tap closed in order to avoid the risk of
damage from water coming out.
60.3 cm
15 kg
75.6 cm
20 kg
4.
Preparing the furniture doors
Important note:
When working on the furniture doors, care should be
taken to the following:



Always carry out screwing jobs on the most stable
part of the furniture door. Never screw into fillings
or similar areas.
Always selects screws with a length smaller than
the thickness of the cabinet front.
Protect the surfaces of the furniture doors during
installation against damage.
The overall weight of the furniture door including the
handle should not exceed the following values:
6.
Appliance width
*
Overall width of the furniture door
Removing positioning aids
Unscrew the positioning aids from the appliance door.
45.1 cm
20 kg (8.5 kg *)
Note:
60.3 cm
25 kg (14.5 kg *)
The positioning aids will still be needed in the course of
mounting.
75.6 cm
29 kg
Wine storage compartment
Instead of one large door, two furniture doors can be
mounted next to each other in the case of appliances
with a width of 76 and 91 cm. These furniture doors are
then connected using a metal strip on the rear.
This metal strip is available from your dealer as an
installation accessory (Connection element for furniture
doors). For further information see section “Tools and
Accessories which are needed”.
Note:
The instructions for carrying out this work step can be
found in the separate installation instructions for this
accessory.
NV
7.
1.
Fastening the adjusting rib to the
furniture door

Measure distance A between the adjusting rail and
the furniture parts above.

Note:
8.
2.
Loosen the two nuts (a) and remove the adjusting
rib (b).
3.
Mark this value A on the rear side of the furniture
door.
4.
Determine the middle of the door and label it.
5.
Rest the adjusting rib on the furniture door and
align to the markings. Mark the drill holes.
6.
Pre-drill the holes.
7.
Tightly screw the adjusting rib.
One screw should be screwed in under the
threaded rod in each case.
The adjusting rib has a various holes for different
furniture door design variations. Always carry out
screwing jobs on the most stable part of the
furniture door.
Fastening the fixing rib to the
furniture door
1.
Hang the furniture door on the threaded rod (a).
2.
Adjust the furniture door using the threaded rod
(Torx screwdriver)
Re-examine the dimensions of the crack
continuously. To do this, use the assembly
gauge (b).
3.
Transfer the position of the fastening screws on the
outer edge of the appliance door to the furniture
door and mark.
4.
Remove furniture door.
The minimum number of screws required for this
depends on the width of the furniture door.
OM
5.
On both lengths of the furniture door, draw
a parallel with the help of the positioning aid.
9.
Mounting the furniture door
Note:
Now attach the door handles which should have been
screwed from behind!
6.
Lengthen the markings to the parallels using an
angle of contact.
7.
Apply the fixing ribs (b) and mark out the holes.
8.
Pre-drill the holes.
9.
Screw on the fixing ribs (b).
1.
Remove fixing bracket (a) from the appliance door.
To do this, loosen the fastening screws (b) only.
2.
Insert the removed fixing brackets (a) into the fixing
ribs (b) on the furniture door.
3.
Open the appliance door.
ON
4.
Hang furniture door with the adjusting rail onto the
threaded rods (1.).
5.
Lower furniture door and push the fixing brackets
down over the fastening screws on the appliance
door (2.).
10. Screw nuts onto the threaded rods of the adjusting
rail and tighten! This way, the lateral adjustment of
the door is fixed.
10. Screw on the lower fixing angle
The lateral adjustment of the door is fixed through the
lower fastening angles.
The number of the lower fastening angles depends on
the width and the design of the furniture door.
Screw on lower bracket. Pre-drill holes into the furniture
door!
1.
Loosen screw.
Adjust the furniture door using the threaded rod
(Torx screwdriver) Re-examine the dimensions of
the crack continuously.
2.
Push bracket over the screw.
3.
Check the lateral position of the door.
4.
Screw in the wood screws.
7.
Close the door and re-examine to make sure that
the depth of the cabinet frontage corresponds with
the adjacent lying fronts. Correct if necessary.
5.
Tighten the screws.
8.
Tighten the fixing anglescrews in order to fix the
depth adjustment.
9.
Close the door and check the lateral adjustment.
Correct the adjustment by lightly banging on the
edge of the open door by hand.
6.
Insert the coverings via the fixing angle.
6.
OO
1.
1.
Fasten the finger protector
4.
Attach the finger protector with the screws on the
fixing brackets.
5.
Test functioning and smooth running of the finger
protector by repeatedly opening and closing the
door.
When positioning the finger protector at the door,
ensure that the fixing holes in the cover strip
correspond with the boreholes in the fixing
brackets.
Mark now the bottom edge of the finger protector
and shorten accordingly.
2.
2.
Push the finger protector into the gap between the
appliance and the niche wall (NK).
3.
Press the cover strip of the finger protector from
top to bottom between the front of the furniture and
the door of the appliance (OK). Ensure that the fixing
holes in the cover strip correspond with the
boreholes in the fixing brackets (PK)!
Attaching the covers
1.
Attach the cover rail.
2.
Attach the light switch cover.
The light switch cover can be screwed to the door.
OP
Only in the case of individual appliances:
1.
Screw on the angle (a) for fastening the cover ribs.
3.
Tensioning the hinge springs
Turn the setting screw with a cross head screwdriver.
I = Spring tensioned
0 = Spring released
2.
Attach the cover ribs (c) to the fastening sheets (b)
and the angles (a).
These are special installation steps.
Instructions are provided after
section D.
 Ice water dispenser, see “Aligning
ice and water dispenser”.
 Cover strips for the wine cooler, see
“Attaching covering strips”
 Door opening angle see “Setting the
door opening angle”.
Only in the case of a side-by-side set up:
Installation of the appliance is now complete.
Insert the cover rib in the crack between the appliances.
The cover rail is included in the installation accessories
for side-by-side installation.
OQ
Special installation steps
Changing over the door hinges
ã
3.
Unscrew the door.
4.
Remove the hinges.
5.
Remove ventilation grille.
Warning:
Before carrying out any work to the door hinges,
release the spring pressure – risk of injury!
Note:


1.
2.
The door stop cannot be exchanged in the case of
freezers with ice and water dispensers.
It is easier to change over the door hinges if the
appliance is placed on its back (place transport
pallet underneath).
Release the spring pressure on the hinge.
In addition,set the screw from I to 0.
Remove the hinge covering.
OR
6.
Re-attach ventilation grille for the changed door
hinges.
7.
Swap the hinge angle to the other side.
8.
Attach ventilation grille.
9.
Swap the fixing parts on the door to the other side.
A replacement part for the ventilation grille is enclosed
with the appliance for adjustment to the changed door
hinges.
OS
10. Attach the hinges to the appliance. Exchange the
hinges crosswise!
Removing/changing the sealing mat
Freezers are fitted with a sealing mat at the factory for
side-by-side installation.
If a single appliance is installed, the sealing mat is not
required and can be removed.
11. Screw the door to the hinges.
The sealing mat is essential for side-by-side installation.
If the door hinges were fitted to the other side of the
door, the sealing mat must also be moved to the
opposite side of the appliance.
12. Tighten the screw. In addition, set the screw from I
to 0.
13. Attach the hinge covers.
OT
Side-by-Side set up
3.
Unscrewing the base panelling.
If a side-by-side set up of two appliances is envisaged,
connect the two appliances to one another now.
1.
Unpack the installation accessories for side-by-side
installation and check that none of the accessories
is missing.
Note:


2.
OU
Freezers are fitted with a sealing mat at the factory
for side-by-side installation.
In this case continue with Step 6.
Always attach sealing mat to the appliance situated
on the left.
4.
Place sealing mat on the appliance and secure with
the attachment pins.
5.
Attach the moisture-absorbing strips from the
installation accessories for side-by-side installation
to the side panel using adhesive tape.
Place appliances side-by-side in the planned
installation configuration.
6.
Screw the connection clamps from the installation
accessories for side-by-side installation to the side
of both appliances. Note the position of the clamps!
8.
Push the appliances together until the angle
brackets interlock.
9.
Insert pins through the angle brackets.
10. Push front of appliances completely together.
7.
Screw the angle brackets from the installation
accessories for side-by-side installation to the
handle side of both appliances.
11. Unscrew screws from the top of the appliance and
in their place screw on the installation aids from the
installation accessories for side-by-side installation.
OV
12. Press appliances completely together by gripping
the installation aids with water pump pliers.
Preparing the water connection
13. When the appliances have been pushed
completely together, push the bar from above
through the connection clamps.
(only for appliances which require a water connection)
Note:
Turn off the main water tap in order to avoid damage
from escaping water.
1.
Connect connection line to the shut-off valve.
2.
Lay the connection pipe. Always keep to the given
installed area in order to avoid damaging the
connection pipe when sliding the appliance in later.
14. Press appliances completely together by gripping
the appliance base with water pump pliers.
15. When the appliances have been pushed
completely together, push the bar from the front
through the connection clamps. Use a suitable tool
to insert the bar all the way.
Connecting the appliance to the water
supply
Note:
Do not kink the connection pipe when bending it,
otherwise there is a risk of leaks and water damage.
16. Remove installation aids.
PM
1.
Remove the plugs from the appliance connection
(1.).
2.
Lay the water hose such that it ends at the
appliance connection (2.).
3.
Slide the union nut and the sealing element onto
the water hose.
4.
Attach the water hose to the appliance connection
and screw on the union nut (3.). Screw tightly, using
manual force.
5.
Screw the union nut tightly using the fixed spanner.
Do not over tighten!
6.
Push water hose back as far as possible into the
protective pipe (4.).
For furniture doors with a 19 mm thickness:
7.
Turn the shut-off valve and the main water tap.
8.
Re-examine the point of connection at the shut-off
valve and the appliance connection for leaks.
9.
Close the shut-off valve.
3.
For furniture doors with a 38 mm thickness:
3.
Aligning ice and water dispenser
(only in the case of freezers with ice and water
dispenser)
Slide the covering frame onto the ice and water
dispenser and press in until the frame is flush with
the door surface.
Press lengthening frame onto the covering frame.
Slide the covering frame onto the ice and water
dispenser and press in until the frame is flush with
the door surface.
Note:
In the case of appliances with a high-grade steel door,
there is a special covering frame.
The ice and water dispenser can be adjusted within the
section of the furniture door. In this way, it is possible to
undertake parallel adjustment to the furniture door in
order to achieve an optimal overall impression.
Note:
We recommend mounting the covering frames before
aligning the ice and water dispenser.
1.
Remove the water capture bowl (a) from the ice
and water dispenser.
2.
Remove the covering (b) from the capture bowl.
PN
1.
Loosen the screws on the 4 clips (1.).
2.
Place a slit screwdriver into one of the 4 slits and
shift the blocks laterally such that the ice and water
dispenser has an equal distance to the furniture
door (2.).
3.
(only for the wine storage cabinet)
1.
In certain circumstances, if the frame width is
narrow, the side of the covering strip has to be
shortened. To determine the required length of the
side, lay trial pieces next to the covering strip.
2.
Slide the covering strips on the longitudinal side
into the gap between the furniture door (a) and the
glass pane (b).
Retighten the screws on the clips (3.).
4.
Apply the covering.
5.
Insert the water capture bowl.
PO
Attaching covering strips
3.
Cut the covering strips of the shortest sides to the
required length.
Setting the door opening angle
According to the set up conditions, it may be necessary
to limit the door opening angle. A door opening angle
of 115° is set at the factory.
To set the door opening angle to 90°:
4.
1.
Open the door to 90°.
2.
Drive in the stop pin with a hammer.
Push cover strips into the gap between the furniture
door (a) and glass pane (b).
PP
Siemens-Electrogeräte GmbH
Carl-Wery-Str. 34
81739 München
Germany
*9000650374*
9000650374
en
(9107)
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising