Siemens | CI36BP01 | Installation instructions | Siemens iQ700 Built-in Fridge-freezer combination, noFrost, Top Freezer Installation instructions

Siemens iQ700 Built-in Fridge-freezer combination, noFrost, Top Freezer Installation instructions
en Installation instructions
CI36....
Built-in appliance
Table of Contents
Safety and Warning Information ........................
4
Installation Possibilities ......................................
5
Stand alone appliance ..............................................
5
Stand alone appliance with dividing wall ..............
1.
Adjusting the appliance
in the niche ........................................... 15
2.
Fastening the appliance
to the niche ceiling .............................. 16
5
3.
Stand alone appliance as an end section
to a row of kitchen units ...........................................
Fastening the appliance to the
side wall of the installation niche...... 16
5
4.
Installing the Appliance ......................................
6
Checking that the finger guard
moves easily ......................................... 17
Installation location ....................................................
6
1.
Fastening the plinth strip ................... 18
Atmosphere grades ..................................................
6
2.
Aligning the base cover .................... 18
3.
Stable installation ......................................................
6
Switching the appliance on
for the first time .................................... 19
Installation niche ........................................................
6
4.
Preparing the furniture doors ........... 19
Neighbouring kitchen furniture ................................
6
5.
Loading the appliance door ............. 19
Subsurface ..................................................................
6
6.
Removing positioning aids ............... 19
7.
Aligning the appliance ..............................................
6
Electrical Connection ..........................................
7
Fastening the adjusting rib
to the furniture door
(refrigerator compartment)................. 20
8.
Water Connection ................................................
7
Dimensions of the Installation Niche .................
8
Fastening the fixing rib
to the furniture door
(refrigerator compartment)................. 20
9.
Tools and Accessories which are needed ........
9
Scope of delivery .......................................................
9
Fastening the adjusting rib
to the furniture door
(freezer compartment) ........................ 21
Additional accessories .............................................
9
Miscellaneous ............................................................
9
Tools ............................................................................
9
Installation Manual .............................................. 10
10. Fastening the fixing rib
to the furniture door
(freezer compartment) ........................ 21
11. Mounting the furniture door
(freezer compartment) ........................ 22
12. Mounting the furniture door
(refrigerator compartment)................. 23
1.
Check the installation niche ............. 10
2.
Removing the packaging .................. 10
3.
Transporting the appliance ............... 11
1.
Fasten the finger protector ............... 25
4.
Installation preparation ...................... 11
2.
Attaching the covers .......................... 25
5.
Special installation steps ................... 11
3.
Tensioning the hinge springs
(refrigerator compartment)................. 26
1.
Attaching the anti-tipping brackets
to the wall .............................................. 12
2.
Attaching alternative anti-tilt device . 13
Preparing the water connection .............. 27
3.
Attaching the edge protectors ......... 13
4.
Sliding the appliance into
the installation niche............................ 14
Connecting the appliance
to the water supply .................................... 27
13. Screw on the lower fixing angle ...... 24
Special Installation Steps ...................................
27
Setting the door opening angle
(refrigerator compartment) ....................... 27
3
Safety and Warning Information
These mounting instructions are designed to help you
install your new appliance.
The manufacturer cannot be held liable for mounting
which has been improperly carried out. We recommend
that you allow a qualified specialist to set up and switch
the appliance on for the first time.
Following all information and keeping to the instructions
are preconditions for mounting and switching the
appliance on safely for the first time.
Keep the mounting instructions safe for use later on.
Before setting up and switching the appliance on for the
first time, read the mounting instructions fully and
thoroughly.
ã Warning
The appliances are very heavy and must be
secured from tipping when transporting, when
mounting and when operating. It is absolutely
necessary to fit an anti-tip device.
Keep the doors closed until the appliance has been
mounted completely and secured according to the
instructions in these mounting instructions.
Because of the weight/dimensions of the appliance
and to minimise the risk of injuries and damage to
the appliance at least two persons are necessary to
set-up the appliance securely.
Use the appliances according to the prescribed
application.
Pull out the plug or remove the fuse before
commencing work on the appliance.
Only customer service may change the power cord
and carry out any other repairs. Improper
installations and repairs may put the user at
considerable risk.
Apart from statutory national regulations, you
should stick to the connection terms relating to the
local electricity and water companies.
4
ã Caution
Setting up and mounting this appliance requires
extensive expertise in various trades (mechanics,
carpentry, plumbing, electrics).
It is the duty of the person setting the appliance up
to guarantee that it is set up and commissioned
securely.
Mistakes in setting the appliance up and damage
resulting from this do not come under the warranty
of the manufacturer. Terms of guarantee are found
in the operating instructions of the appliances.
Installation Possibilities
Various installation possibilities are available.
These are only limited by the kitchen design and the
finger protector function.
Stand alone appliance
Stand alone appliance as an end
section to a row of kitchen units
If a side of the appliance is visible, use a side covering.
The side covering must be connected firmly to the wall,
the floor and the upper cupboards before the appliance
is slid into the installation niche.
The dimensions of the side covering are governed by
the opposing niche wall. During installation, make sure
that the installation niche has right angles and has the
exact size necessary for the appliance.
Stand alone appliance with dividing
wall



When measuring the dividing wall for model 4, pay
attention to the thickness of the furniture front to be
mounted in order to avoid damage when opening
doors at the same time.
If the distance between the appliances is less than
160 mm, the auxiliary side heater must be used.
For further information see section “Tools and
Accessories which are needed”.
The minimum thickness of the dividing walls is
16 mm.
5
Installing the Appliance
Installation location
Installation niche
ã
It is important to keep to the stated dimensions of the
installation niche with a view to trouble-free fitting, and
the subsequent appearance of the kitchen furniture
frontage.
Caution:
The appliance is very heavy.
Weight (empty): 195 kg
The appliance should be installed in a dry, well
ventilated space.
The location should not be exposed to the direct
sunlight and should not lie next to a source of heat such
as a cooker or a radiator etc. If installation next to a
source of heat cannot be avoided, either a suitable
insulating plate should be used or you should keep to
the following minimum distances:

3 cm to electric or gas cookers.

30 cm to an oil-fired or solid-fuel cooker.
The floor of the installation location must not give way;
if required, reinforce floor. To ensure that the ice maker
functions correctly, the appliance must be upright.
Atmosphere grades
The climate class can be found on the rating plate. The
climate class indicates within which ambient
temperatures the appliance can be operated.
Climate class
Permitted ambient
temperature
SN
+10 °C to 32 °C
N
+16 °C to 32 °C
ST
+16 °C to 38 °C
T
+16 °C to 43 °C
Stable installation
The appliance is very heavy and has a tendency to tilt
forwards when the appliance door is opened.
The appliance must not be switched on until there is
no possibility of the appliance tilting over.
The safest method of installing the appliance in a stable
position is to use the supplied anti-tilt brackets.
If the installation cavity is adequately stable and the
appliance can be attached securely to the upper and
side walls of the cavity, it may be possible to dispense
with the anti-tilt brackets. A prerequisite for this is
always a firm connection between the cavity and back
wall!
In the case of doubt, the help of architect or specialist
builder should be enlisted.
6
Special care should be taken that the niche has right
angles. The side walls should not exhibit areas that
stick out, projections or unevenness.
You should determine the right angles of the installation
niche with appropriate means, e.g. by measuring
diagonally and by using a spirit level.
The side walls and the upper end of the installation
niche must be at least 16 mm thick.
Neighbouring kitchen furniture
The new appliance is screwed down tightly using parts
of the cabinet and the upper cabinet.
Care should therefore be taken, that all upper cabinets
to which something has been fastened are securely
connected to the subsurface or wall by appropriate
means.
The minimum thickness of the base should be
a minimum of 19 mm.
Subsurface
ã
Caution:
A fully laden appliance is heavy.
Weight (laden): approx. 540 kg
The subsurface must be level and even in order to
ensure that the appliance is securely installed and
works correctly.
The subsurface must be made from a hard, non-flexible
material.
The floor of the installation space must have the same
height as the rest of the space.
On account of the weight of a fully-laden appliance, it is
necessary to have a bearing subsurface. In the case of
doubt, the help of architect or specialist builder should
be enlisted.
Aligning the appliance
To ensure that the appliance functions correctly, it must
be set level with a spirit level.
If the appliance is not level, water may flow out of the
ice maker, ice cubes may be irregular or the doors may
not close properly.
Electrical Connection
Water Connection
The socket must be near the appliance and also freely
accessible following installation of the appliance.
ã
The appliance complies with the protection class I.
Connect the appliance to 220–240 V/50 Hz alternating
current via a correctly installed socket with protective
conductor. The socket must be fused with a 10 to 16 A
fuse.
A cold water connection is necessary for operating the
automatic ice maker. The water pressure must lie
between 1.7 and 10 bar. The installation must
correspond to the local plumbing regulations.
For appliances operated in non-European countries,
check whether the stated voltage and current type
match the values of your mains supply match the values
of the mains supply. These specifications can be found
on the rating plate.
ã
Warning:
Never connect the appliance to electronic energy
saver plugs. Our appliances can be used with
mains and sine-controlled inverters. Mainscontrolled inverters are used for photovoltaic
systems which are connected directly to the
power supply system. Sine-controlled inverters
must be used for isolated applications (e.g. on
ships or in mountain lodges) which are not
connected directly to the national grid.
Warning:
Connect the appliance to a cold water pipe only.
A separate shut-off valve should be installed in the coldwater inflow.
The shut-off valve should not be located behind the
appliance. It is recommended that you mount the shutoff valve directly next to the appliance or at another
place which is easily accessible.
When installing the water connection, pay attention to
the permissible installation area for the water mains.
For more information concerning the permissible
installation area, see the section “Dimensions of the
Installation Niche”.
Note, if the water line for the cold water connection
is not included in the product package:


For connection to the drinking water mains use
only water pipes which are suitable for drinking
water. Observe national regulations and the
connection conditions of the local water supply
companies.
The maximum outside diameter of the water mains
(without connecting pieces) is 10 mm.
7
Dimensions of the Installation Niche
Important:
The upper niche wall must consist of
a rigid, load bearing material
(minimum thickness 16 mm).
Important:
The lateral niche walls must be
completely even and free from
bumps. If the niche is formed as a
separate part, the side walls must be
completely even up to a depth of at
least 100 mm and free from bumps.
Key:
A
Area for installation of the water connection
B
Area for installation of the electric current
C
Depth of the installation niche, depending on the kitchen design
C = 610 mm minimum!
8
Tools and Accessories which are needed
Scope of delivery



Tools
Installation manual
Operating instructions
Installation accessories
Rechargeable screwdriver
Additional accessories
Lateral additional heating
T20 Torx-bit magnetic holder
Necessary when the distance between two appliances
is less than 160 mm.
Connecting element for furniture doors
For connecting two furniture doors (see explanation in
Section “C / 3. Switching the appliance on for the first
time”). It can be used for standard height furniture
doors without any preparation work.
T20 Torx screwdriver
8 mm socket wrench
Miscellaneous










Step ladder
Various size drills
Trolley, wheelbarrow or sack barrow
Hammer drill for drilling holes into the wall and floor
Various size drills for various materials
Wood plank, (min. 8 x 10 cm) as an alternative antitip device. Length should correspond to the width
of the installation niche.
Fixed spanner,
wrench size 13 mm
Water pump pliers
Various size wood screws
Screw (M8, at least 80 mm long), nut
Thin (1.5 mm), material suitable for protecting the
floor against damage (e.g. linoleum)
Suitable material for covering and protecting the
cabinets (e.g. protective film)
Adjustable spanner
Knife with an adjustable
blade
Adhesive tape
Note:
Before using, check whether the removed adhesive
tape leaves adhesive residue on the work surfaces!
Otherwise do not use on high-quality work
surfaces.
Metal tape measure, folding
ruler
Angle of contact
60 cm and 120 cm spirit
levels
Level, min. 120 cm long
9
Installation Manual
The following mounting instructions describe mounting
steps for various appliance models.
Therefore, deviations may occur from that shown in the
diagrams.
2.
Removing the packaging
ã
Warning:
 The appliance could tip over when unpacking.
 The appliance could tip over when the
Reference is made to specific mounting steps for
individual appliances.
1.
Check the installation niche
ã
Caution:
Before starting the installation, check carefully
that the installation cavity meets the requirements for a secure and trouble-free installation:
1.
Check the subsurface.
Follow the notes in the section “Installing the
Appliance”.
2.
Check the dimensions of the niche.
3.
Re-examine whether the niche has right angles.
4.
Re-examine the positioning of the plug.
Additionally follow the instructions in the sections
“Electrical Connection” and “Dimensions of the
Installation Niche”.
5.
appliance door is opened.
 The appliance is very heavy.
Risk of personal injury and damage to the
appliance!
Note:
Check the appliance for damage. Do not install the
appliance if there is visible damage. If there are queries,
please contact the dealer.
To protect the subsurface from damage whilst
installing:
1.
Place cardboard or plywood under the appliance.
2.
Remove packaging carton. Be careful when using
the knife so as not to damage the surface of the
appliance.
3.
Remove accessories from the outside of the
appliance.
Keep adhesive tape which was used to attach the
supplied accessories to the appliance. It is
used subsequently for attaching the edge
protection to the cavity walls (see Section “A /
3. Attaching the edge protectors”).
Check the positioning of the water connection (for
appliances with ice maker)
Additionally follow the instructions in the sections
“Water Connection” and “Dimensions of the
Installation Niche”.
6.
Re-examine the stability and fastening of the
neighbouring cabinet parts. All cabinet parts in the
vicinity of the appliance have to be firmly
connected to the wall.
7.
Re-examine that when opening the appliance door,
it does not collide with neighbouring kitchen parts
(for door opening angle).
4.
Remove transportation protection devices (a) and
lift appliance off the pallet – appliance is very
heavy!
5.
Carefully open the appliance – risk of tipping over
– and remove accessories and installation
materials from inside the appliance. Close the door
again.
Note:
Only remove the transporting securing units with
which the slide-in bases and the storage
compartments in the appliance are protected after
completing the installation as otherwise, parts
could be damaged.
10
3.
Transporting the appliance
4.
ã
Warning:
Unpack installation materials and accessories.
The appliance is very heavy. Handle it carefully,
as otherwise people helping to lift it could be hurt
or the appliance could be damaged.
To simplify installation, the packages are identified with
labels A, B, C and D corresponding with the manual
sections.
Installation preparation
The appliance has a height of 2,126 mm. If it is not
possible to support the appliance in a vertical position
because of the structure of the building, the appliance
can be transported on its side.
Note:
Never put the appliance up via its side! Risk of damage
to the appliance.
When putting the appliance up, pay attention to the
minimum height that is required at the assembly
location according to the following table.
Putting the appliance
up on via its back side
Putting the appliance
up via its side wall
5.
Special installation steps
This symbol indicates that additional steps need to be
taken before proceeding to the next chapter.
Special installation steps are described after section D.
Minimum height
218.5 cm
Never put the appliance
up via its side!
aufrichten!
Note:
Never push means of transportation under the front of
the appliance. Risk of damage to the appliance
1.
Transport the appliance with an aid to transport
which is suitable (sack barrow, trolley or
wheelbarrow).
2.
When transporting, secure the appliance from
being tipped.
 Water connection see “Preparing the
water connection“ and „Connecting
the appliance to the water supply”.
 Door opening angle see “Setting the
door opening angle
(refrigerator compartment)”.
11
1.
Attaching the anti-tipping brackets
to the wall
ã
Warning:
Ensure that in the wall area there are no
electrical wires or pipes which could be
damaged by pipes. Risk of injury or damage!
ã
Warning:
When installing or working with floor anchors
always use protective glasses and other
protective equipment or protective clothing – risk
of injury!
Note:



Each appliance requires 2 anti-tilt brackets.
The set supplied, contains fastening screws for
various subsurfaces. Select the fastening screws
corresponding to the local conditions.
If the anti-tilt brackets, and therefore the appliance,
cannot be securely attached with the supplied
fastening screws, another suitable method must be
used to attach the appliance securely.
The anti-tilt brackets (a) must overlap the appliance by at
least 105 mm to ensure that the appliance is stable.
If the minimum overlap cannot be observed due to
structural conditions, these can be overcome by the
attachment of a suitable device, e.g. an adequately
dimensioned beam (b) behind the brackets.
The length of the plank should correspond to the width
of the installation niche!
Important information concerning attachment with
wall plugs and screws:



1.
Determine the fastening points of the anti-tilt ribs.
Determine the actual dimensions according to the
section “Dimensions of the Installation Niche”.
2.
12
Screw on the anti-tilt brackets tightly. Re-examine to
make sure that the screws are firmly tightened.
Not suitable for use in light-weight masonry such as
hollow blocks or tiles!
Never use in fresh concrete which has not yet
hardened.
Do not use spiral-flute counterbores
(countersinking tool) to drill the holes.
2.
Attaching alternative anti-tilt
device
Important note:
If the anti-tilt brackets cannot be securely attached, a
wooden beam can be used above the appliance as an
alternative anti-tilt device. Care should be taken that
there is not a gap between the appliance and the
wooden beam. As far as possible, always screw the
wooden plank to the rear wall of the niche.
1.
3.
Attaching the edge protectors
To protect the edges of the installation cavity, it is
recommended to attach edge protection made of a
suitable material.
Attach the edge protection with the adhesive tape which
was used to attach the accessories to the appliance.
Cut the wooden plank to the required length (cross
section min. 8 x 10 cm). The length should
correspond to the width of the installation niche!
Note:
 If the installation niche is deeper than the
appliance, select a stronger beam or use two,
one behind the other.
 The plank must overlap the appliance by at least
50 mm.
This is a special installation step.
Instructions are provided after
section D.
 Water connection see “Preparing the
water connection”.
2.
Mark the installation height (underside edge of the
plank) on the rear wall of the niche.
3.
Select the screws according to the thickness of the
wooden plank: Length min. 2.5 x wood thickness,
diameter 12 or 14 mm.
Note:
Select the number of screws corresponding to the
niche width so that you ensure that the plank can
be securely mounted.
According to the subsurface:
4.
Look for the supports on the rear wall of the niche
and mark the drill holes on the plank
corresponding to the position of the support.
or
5.
Fasten suitable dowel into the rear wall.
6.
Pre-drill.
7.
Screw the plank onto the rear wall of the niche.
13
4.
Sliding the appliance into the installation niche
ã
Caution:
5.
Be careful when sliding the appliance into the
installation niche. Do not damage the water
connection or power cord.
Protect the mains lead from getting wedged under
or behind the appliance.
Recommended procedure:
Tie a piece of string in the middle of the power cord
and guide the string forwards over the appliance.
When pushing the appliance into the cavity, pull the
cable upwards with the string.
Note:
If the floor or appliance is skew in relation to the
installation niche, the height-adjustable wheels should
be correspondingly adjusted before sliding the
appliance into the niche.
or
Fasten the mains lead onto the floor with adhesive
tape, in the middle behind the appliance approx.
38 cm from the rear of the niche.
1.
Remove the base panelling.
2.
Unscrew the height-adjustable feet at the back of
the appliance by approx. 10 mm.
6.
Slide the appliance carefully into the niche.
3.
Plug the mains plug into the socket.
7.
4.
Insert water connection line into the protective pipe
on the rear of the appliance.
Remove edge protection from the installation cavity
(if previously attached).
ã
Warning:
The appliance may tilt when the water
connection line is inserted into the protective
pipe (a)!
14
1.
Adjusting the appliance in the
niche
The assembly gauge (b) is used to set
this height correctly. The upper edge of
the gauge must be in alignment with the
mark on the appliance.
Note:




To ensure that the appliance functions correctly,
it must be set level with a spirit level.
2.
Unscrew the height-adjustable feet at the front of
the appliance until the mark (a) on the base has
reached the indicated height (32 mm).
3.
Align the appliance vertically using the feet at the
back. Use spirit level.
Do not tip the appliance in the niche! When
screwing down the height adjustable feet, proceed
step by step. Lower by alternating left to right.
The rear feet can be set easier when the appliance
is not loaded on the rear.
When using a wooden plank as an alternative antitilt mechanism of these mounting instructions, turn
the appliance as far as it will go against the wooden
plank. Do not bend against the wooden plank.
The positioning supports are set out for the following
overall strengths of the furniture doors to be mounted.


19 mm
38 mm
Re-examine the actual thickness of the doors to be
mounted in order where necessary, to be able to
compensate possible digressions.
1.
Adjust the appliance to the existing furniture.
Keep the straight edge on the door, above the
positioning supports.
The height-adjustable feet on the front and rear can all
be adjusted from the front.
Front:
with a fixed spanner, wrench size 13 mm
Rear:
with a 8 mm socket spanner with flexible
shaft. Use cordless screwdriver.
A mark (a) is made on the base of the appliance which
serves as a standard measurement for setting the
height. When setting the height, raise the mark to
32 mm above the ground. This dimension is very
important for the subsequent adjustment of the cabinet
frontage.
15
2.
Fastening the appliance to the
niche ceiling
6.
Attach the covering ribs (b) onto the fastening
sheets (above).
Note:
It is essential to attach the appliance to the ceiling of the
cavity.
1.
Screw on the front bars of the fastening sheets
(above) with the upper cabinets.
2.
If there is a large crack available above the
appliance, integrate a wooden plank above the
appliance and pay attention that the crack is
completely filled.
3.
If there enough room on the top of the appliance fix
the the lateral bars of the fastening sheets (above)
to the side of the niche.
4.
Cut the connection ribs (a) to the desired height!
5.
Press connection ribs (a) into the covering ribs.
16
3.
Fastening the appliance to the side
wall of the installation niche
Screw on the bars of the fastening sheets with the
cabinet parts located next to them.
4.
Checking that the finger guard
moves easily
It is now essential to check that the finger guard moves
easily. At a later time any required corrections will be
more difficult.
This is a special installation step.
Instructions are provided after
section D.
 Water connection see “Connecting
the appliance to the water supply”.
Note:


The supplied finger protector can be used for both
sides of the hinges.
Because of different installation possibilities, the
finger protector has to be shortened to the required
length.
1.
Shorten the finger protector at the upper side
above the covering strip by 55 mm (1.).
2.
Push the cut-off remnant on the hinge side into the
gap between the appliance and cavity wall.
The part must be easy to push in and pull out (2.)!
3.
Ensure smooth running at all positions of the
door (3.).
17
1.
Fastening the plinth strip
Note:
Never cover the ventilation cracks in the base panelling.
Risk of damage to the appliance.
2.
1.
Place base cover on the appliance (do not screw
on).
2.
Measure the difference in depth A between the
base panelling and the base strip of the adjacent
lower cabinets.
3.
Remove the base panelling again.
4.
Adjust the brackets (a) to the dimensions A and
tighten.
5.
Fasten the base panelling.
Nominal dimensions to be observed:
1.
Where necessary, cut the base strip to the required
length.
2.
Place base cover on the appliance (do not screw
on).
3.
Take the protective film off from the adhesive pads
on the Velcro strip.
4.
Put the base strip onto the base panelling and push
firmly.
5.
Base strip can be screwed to the base cover from
behind. There are holes in the base cover for this
purpose.
18
Aligning the base cover
3.
Switching the appliance on for the
first time
The appliance should now be switched on for the first
time in order to ensure the accuracy of the following
mounting steps and with it, the appearance of the entire
kitchen frontage.
1.
Open the appliance door.
2.
Actuate the appliance’s On/Off button.
Only for appliances with a water connection:
In the case of possible damage of the water mains,
keep the shut-off tap closed in order to avoid the risk of
damage from water coming out.
4.
5.
Loading the appliance door
When attaching the furniture doors it is recommended
to load the storage sections in the door with weights in
order to ensure that the when adjusting crack
dimensions turn out to be as precise as possible.
Loading recommendations:
Loading of the appliance door
Refrigeration
compartment door
Freezer drawer
2 x 12 kg
10 kg
Preparing the furniture doors
Important note:
When working on the furniture doors, care should be
taken to the following:



Always carry out screwing jobs on the most stable
part of the furniture door. Never screw into fillings
or similar areas.
Always selects screws with a length smaller than
the thickness of the cabinet front.
Protect the surfaces of the furniture doors during
installation against damage.
The overall weight of the furniture door including the
handle should not exceed the following values:
Overall width of the furniture door
Refrigeration
compartment door
Freezer drawer
2 x 13 kg
6.
Removing positioning aids
Unscrew the positioning aids from the appliance door.
Note:
13 kg
Instead of one large door, two furniture doors can be
mounted next to each other in the case of appliances
with a width of 76 and 91 cm. These furniture doors are
then connected using a metal strip on the rear.
The positioning aids will still be needed in the course of
mounting.
This metal strip is available from your dealer as an
installation accessory (connection element for furniture
doors). For further information see section “Tools and
Accessories which are needed”.
Note:
The instructions for carrying out this work step can be
found in the separate installation instructions for this
accessory.
19
7.
Fastening the adjusting rib to the
furniture door
(refrigerator compartment)
8.
1.
Measure distance A between the adjusting rail and
the furniture parts above.
1.
Hang the furniture door on the threaded rod (a).
2.
Adjust the furniture door using the threaded rod
(Torx screwdriver).
Re-examine the dimensions of the crack
continuously. To do this, use the assembly
gauge (b).
3.
Transfer the position of the fastening screws on the
outer edge of the appliance door to the furniture
door and mark.
4.
Remove furniture door.
5.
On both lengths of the furniture door, draw
a parallel with the help of the positioning aid.
2.
Loosen the two nuts (a) and remove the adjusting
rib (b).
3.
Mark this value A on the rear side of the furniture
door.
4.
Determine the middle of the door and label it.
5.
Rest the adjusting rib on the furniture door and
align to the markings. Mark the drill holes.
6.
Pre-drill the holes.
7.
Tightly screw the adjusting rib.
Note:


20
Attach the adjusting rib with at least 6 screws on
the furniture door. One screw should be screwed in
under the threaded rod in each case.
The adjusting rib has a various holes for different
furniture door design variations. Always carry out
screwing jobs on the most stable part of the
furniture door.
Fastening the fixing rib to the
furniture door
(refrigerator compartment)
6.
Lengthen the markings to the parallels using an
angle of contact.
7.
Apply the fixing ribs (b) and mark out the holes.
8.
Pre-drill the holes.
9.
Screw on the fixing ribs (b).
6.
Pre-drill the holes.
7.
Tightly screw the adjusting rib.
Note:

10. Hang the furniture door on the threaded rods.
9.
Fastening the adjusting rib to the
furniture door
(freezer compartment)
1.
Measure distance A between the adjusting ribs and
the bottom edge of the refrigerator compartment
door.
2.
Loosen the two nuts (a) and remove the adjusting
rib (b).
3.
Mark this value A on the rear side of the furniture
door.
4.
Determine the middle of the door and label it.
5.
Rest the adjusting rib on the furniture door and
align to the markings. Mark the drill holes.

Attach the adjusting rib with at least 10 screws on
the furniture door. One screw should be screwed in
under the threaded rod in each case.
The adjusting rib has a various holes for different
furniture door design variations. Always carry out
screwing jobs on the most stable part of the
furniture door.
10. Fastening the fixing rib to the
furniture door
(freezer compartment)
1.
Hang the furniture door on the threaded rod (a).
2.
Adjust the furniture door using the threaded rod
(Torx screwdriver).
Re-examine the dimensions of the crack
continuously. To do this, use the assembly
gauge (b).
21
3.
Transfer the position of the fastening screws on the
outer edge of the appliance door to the furniture
door and mark.
11. Mounting the furniture door
(freezer compartment)
Note:
Now attach the door handles which should have been
screwed from behind!
4.
Remove furniture door.
5.
On both lengths of the furniture door, draw a
parallel with the help of the positioning aid.
6.
Lengthen the markings to the parallels using an
angle of contact.
7.
Apply the fixing ribs (b) and mark out the holes.
8.
Pre-drill the holes.
9.
Screw on the fixing ribs (b).
22
1.
Remove fixing bracket (a) from the appliance door.
To do this, loosen the fastening screws (b) only.
2.
Insert the removed fixing brackets (a) into the fixing
ribs (b) on the furniture door.
3.
Open the drawer.
4.
Hang furniture door with the adjusting rail onto the
threaded rods (1.).
5.
Lower furniture door and push the fixing brackets
down over the fastening screws on the appliance
door (2.).
10. Screw nuts onto the threaded rods of the adjusting
rail and tighten! This way, the lateral adjustment of
the door is fixed.
12. Mounting the furniture door
(refrigerator compartment)
Note:
Now attach the door handles which should have been
screwed from behind!
6.
Adjust the furniture door using the threaded rod
(Torx screwdriver).
Re-examine the dimensions of the crack
continuously.
7.
Close the door and re-examine to make sure that
the depth of the cabinet frontage corresponds with
the adjacent lying fronts. Correct if necessary.
8.
Tighten the fixing anglescrews in order to fix the
depth adjustment.
9.
Close the door and check the lateral adjustment.
Correct the adjustment by lightly banging on the
edge of the open door by hand.
1.
Remove fixing bracket (a) from the appliance door.
To do this, loosen the fastening screws (b) only.
2.
Insert the removed fixing brackets (a) into the fixing
ribs (b) on the furniture door.
3.
Open the appliance door.
23
4.
Hang furniture door with the adjusting rail onto the
threaded rods (1.).
5.
Lower furniture door and push the fixing brackets
down over the fastening screws on the appliance
door (2.).
10. Screw nuts onto the threaded rods of the adjusting
rail and tighten! This way, the lateral adjustment of
the door is fixed.
13. Screw on the lower fixing angle
The lateral adjustment of the door is fixed through the
lower fastening angles.
The number of the lower fastening angles depends on
the width and the design of the furniture door.
Screw on lower bracket. Pre-drill holes into the furniture
door!
6.
Adjust the furniture door using the threaded rod
(Torx screwdriver).
Re-examine the dimensions of the crack
continuously.
7.
Close the door and re-examine to make sure that
the depth of the cabinet frontage corresponds with
the adjacent lying fronts. Correct if necessary.
8.
Tighten the fixing anglescrews in order to fix the
depth adjustment.
9.
Close the door and check the lateral adjustment.
Correct the adjustment by lightly banging on the
edge of the open door by hand.
24
1.
Loosen screw.
2.
Push bracket over the screw.
3.
Check the lateral position of the door.
4.
Screw in the wood screws.
5.
Tighten the screws.
6.
Insert the coverings via the fixing angle.
1.
1.
Fasten the finger protector
4.
Attach the finger protector with the screws on the
fixing brackets.
5.
Test functioning and smooth running of the finger
protector by repeatedly opening and closing the
door.
When positioning the finger protector at the door,
ensure that the fixing holes in the cover strip
correspond with the boreholes in the fixing
brackets.
Mark now the bottom edge of the finger protector
and shorten accordingly.
2.
2.
Push the finger protector into the gap between the
appliance and the niche wall (1.).
3.
Press the cover strip of the finger protector from
top to bottom between the front of the furniture and
the door of the appliance (2.).
Ensure that the fixing holes in the cover strip
correspond with the boreholes in the fixing
brackets (3.)!
Attaching the covers
1.
Attach the cover ribs (a) & (b) to the doors and the
freezer compartment drawer.
2.
Attach the light switch cover.
The light switch cover can be screwed to the door.
25
3.
Attach the covering bar above the adjusting ribs of
the freezer compartment drawer.
This is a special installation step.
Instructions are provided after
section D.
 Door opening angle see “Setting the
door opening angle
(refrigerator compartment)”.
3.
Tensioning the hinge springs
(refrigerator compartment)
Turn the setting screw with a cross head screwdriver.
I = Spring tensioned
0 = Spring released
Installation of the appliance is now complete.
26
Special Installation Steps
Preparing the water connection
(only for appliances which require a water connection)
Note:
Turn off the main water tap in order to avoid damage
from escaping water.
1.
Connect connection line to the shut-off valve.
2.
Lay the connection pipe. Always keep to the given
installed area in order to avoid damaging the
connection pipe when sliding the appliance in later.
Connecting the appliance to the water
supply
Note:
Do not kink the connection pipe when bending it,
otherwise there is a risk of leaks and water damage.
1.
Remove the plugs from the appliance connection
(1.).
2.
Lay the water hose such that it ends at the
appliance connection (2.).
3.
Slide the union nut and the sealing element onto
the water hose.
4.
Attach the water hose to the appliance connection
and screw on the union nut (3.). Screw tightly, using
manual force.
5.
Screw the union nut tightly using the fixed spanner.
Do not over tighten!
6.
Push water hose back as far as possible into the
protective pipe (4.).
7.
Turn the shut-off valve and the main water tap.
8.
Re-examine the point of connection at the shut-off
valve and the appliance connection for leaks.
9.
Close the shut-off valve.
Setting the door opening angle
(refrigerator compartment)
According to the set up conditions, it may be necessary
to limit the door opening angle. A door opening angle
of 115° is set at the factory.
To set the door opening angle to 90°:
1.
Open the door to 90°.
2.
Drive in the stop pin with a hammer.
27
Siemens-Electrogeräte GmbH
Carl-Wery-Str. 34
81739 München
Germany
*9000650402*
9000650402
en
(9108)
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising