Samsung | WM55R | User manual | Samsung WM65R User manual

Samsung WM65R User manual
User Manual
WM55R WM65R
The colour and the appearance may differ depending on the product, and the content in the
manual is subject to change without prior notice to improve the performance.
Recommended hours of use per day of this product is under 16 hours. If the product is used for
longer than 16 hours a day, the warranty may be void.
An administration fee may be charged in the following situations:
(a) An engineer is called out at your request, but it is found that the product has no defect (i.e.,
where the user manual has not been read).
(b) You bring the unit to a repair centre, but it is found that the product has no defect (i.e.,
where the user manual has not been read).
You will be informed of the administration fee amount before a technician visits.
© Samsung Electronics
Samsung Electronics owns the copyright for this manual. Use or reproduction of this manual in parts or entirety without the authorization of Samsung Electronics is prohibited.
Trademarks other than Samsung Electronics are property of their respective owners.
Table of contents
Before Using the Product
Writing
Safety Precautions
Storage
Electricity and safety
Installation
Operation
4
4
4
5
6
Precautions for Use
8
Preparations
Checking the Components
9
Parts
10
Ports
Tray (optional purchase)
11
12
IMPORT
What's a 'Roll'?
21
PEN MODE
Screen Elements
Drawing
Erasing
Changing the pen thickness and colour
22
22
23
23
23
BRUSH MODE
Screen Elements
Changing the brush colour
24
24
25
Managing Rolls
ROLL EXPLORER
26
27
Page Viewer
28
Note On/Off
29
Using the Selection Tools
30
Connecting to a Mobile Device
Connecting using Smart View or Screen
Mirroring
Connecting using NFC tagging
32
Connecting to a PC
Connecting using a cable
Connecting via the WiFi Display function
33
33
33
Importing from a USB Device
34
Importing from a Network Drive
34
Source Window
35
Document view
36
Image view
37
32
32
Before Installing the Product (Installation
Guide)
WM55R
WM65R
13
13
14
EXPORT
Sending Email
39
Installing the Wall Mount
Installing the Wall Mount
Wall Mount Kit Specifications (VESA)
15
15
15
Printing
Installing Flip Printing Software
Setting up the printer
40
40
40
Connecting to a network
Network Settings (Wired)
Network Settings (Wireless)
Use WPS
16
16
18
20
Exporting to a USB Device
42
Sharing your screen
43
Exporting from a Network Drive
44
Sending to a mobile device
44
2
Table of contents
Menu
Specifications
Connect
45
General
64
System
53
Preset Timing Modes
66
Picture
56
Support
58
Troubleshooting Guide
Problems and Solutions
59
Appendix
Responsibility for the Pay Service (Cost to
Customers)
67
Not a product defect
67
A Product damage caused by customer's fault 67
67
Others
Prevention of Afterimage Burn-in
What is afterimage burn-in?
Recommended prevention practices
68
68
68
Licence
68
3
Chapter 01
Before Using the Product
Safety Precautions
Warning
A serious or fatal injury may result if instructions are not followed.
Caution
Personal injury or damage to properties may result if instructions are not followed.
Storage
Due to the characteristics of high-glossy products, using a UV humidifier nearby may create
white-colored stains on the product.
"" Contact Customer Service Centre if the inside of the product needs cleaning (service fee
will be charged).
Electricity and safety
Warning
Activities marked by this symbol are prohibited.
Do not use a damaged power cord or plug, or a loose power socket.
An electric shock or fire may result.
Do not use multiple products with a single power socket.
Instructions marked by this symbol must be followed.
Overheated power sockets may cause a fire.
Do not touch the power plug with wet hands. Otherwise, an electric shock may result.
Do not bend or pull the power cord with force. Be careful not to leave the power cord
under a heavy object.
Damage to the cord may result in a fire or electric shock.
Do not place the power cord or product near heat sources.
A fire or electric shock may result.
4
Insert the power plug all the way in so it is not loose.
An unsecure connection may cause a fire.
Connect the power plug to a grounded power socket (type 1 insulated devices only).
An electric shock or injury may result.
Clean any dust around the pins of the power plug or the power socket with a dry cloth.
A fire may result.
Caution
Installation
Warning
DO NOT PLACE CANDLES, INSECT REPELLANTS OR CIGARETTES ON TOP OF THE
PRODUCT. DO NOT INSTALL THE PRODUCT NEAR HEAT SOURCES.
A fire may result.
Do not install the product in poorly ventilated spaces such as a bookcase or closet.
Do not disconnect the power cord while the product is being used.
The product may become damaged by an electric shock.
Only use the power cord provided with your product by Samsung. Do not use the power
cord with other products.
An increased internal temperature may cause a fire.
Do not install the product on an unstable or vibrating surface (insecure shelf, sloped
surface, etc.)
•• The product may fall and become damaged and/or cause an injury.
A fire or electric shock may result.
•• Using the product in an area with excess vibration may damage the product or
cause a fire.
Keep the power socket where the power cord is connected unobstructed.
Do not expose the product to direct sunlight, heat, or a hot object such as a stove.
The power cord must be disconnected to cut off power to the product when an issue
occurs.
The product lifespan may be reduced or a fire may result.
Hold the plug when disconnecting the power cord from the power socket.
•• The product may fall and injure children.
An electric shock or fire may result.
•• As the front is heavy, install the product on a flat and stable surface.
Do not install the product within the reach of young children.
Edible oil, such as soybean oil, can damage or deform the product. Do not install the
product in a kitchen or near a kitchen counter.
Have a technician install the wall-mount hanger.
•• Installation by an unqualified person can result in an injury.
•• Only use approved cabinets.
Install the product at least 10 cm away from the wall to allow ventilation.
An increased internal temperature may cause a fire.
5
Keep the plastic packaging out of the reach of children.
Children may suffocate.
Do not install the product in a vehicle or a place exposed to dust, moisture (water drips,
etc.), oil, or smoke.
A fire or electric shock may result.
Caution
Operation
Warning
There is a high voltage inside the product. Never disassemble, repair or modify the
product yourself.
•• A fire or electric shock may result.
•• Contact Samsung Customer Service Centre for repairs.
Do not set down the product on its front.
Do not let children hang from the product or climb on top of it.
The screen may become damaged.
Children may become injured or seriously harmed.
Do not drop the product while moving.
Product failure or personal injury may result.
If the product is dropped or the outer case is damaged, turn off the power switch and
disconnect the power cord. Then contact Samsung Customer Service Centre.
Set down the product gently.
Continued use can result in a fire or electric shock.
Product failure or personal injury may result.
Do not leave heavy objects or items that children like (toys, sweets, etc.) on top of the
product.
Installing the product in an unusual place (a place exposed to a lot of fine dust, chemical
substances, extreme temperatures or a significant presence of moisture, or a place
where the product will operate continuously for an extended period of time) may
seriously affect its performance.
Be sure to consult Samsung Customer Service Centre if you want to install the
product at such a place.
The product or heavy objects may fall as children try to reach for the toys or sweets
resulting in a serious injury.
Do not move the product by pulling the power cord or any cable.
Product failure, an electric shock or fire may result from a damaged cable.
Do not lift or move the product by pulling the power cord or any cable.
Product failure, an electric shock or fire may result from a damaged cable.
Ensure the vents are not blocked by tablecloths or curtains.
An increased internal temperature may cause a fire.
Do not insert metallic objects (chopsticks, coins, hairpins, etc) or objects that burn easily
(paper, matches, etc) into the product (via the vent or input/output ports, etc).
•• Be sure to power off the product and disconnect the power cord when water
or other foreign substances have entered the product. Then contact Samsung
Customer Service Centre.
•• Product failure, an electric shock or fire may result.
6
Do not place objects containing liquid (vases, pots, bottles, etc) or metallic objects on
top of the product.
•• Be sure to power off the product and disconnect the power cord when water
or other foreign substances have entered the product. Then contact Samsung
Customer Service Centre.
•• Product failure, an electric shock or fire may result.
Before moving the product, turn off the power switch and disconnect the power cable
and all other connected cables.
Damage to the cord may result in a fire or electric shock.
If the product generates abnormal sounds, a burning smell or smoke, disconnect the
power cord immediately and contact Samsung Customer Service Centre.
An electric shock or fire may result.
During a lightning or thunderstorm, power off the product and remove the power cable.
A fire or electric shock may result.
Do not drop objects on the product or apply impact.
A fire or electric shock may result.
Caution
Do not use humidifiers or stoves around the product.
A fire or electric shock may result.
Do not touch the screen when the product has been turned on for an extended period of
time as it will become hot.
Do not place heavy objects on the product.
Product failure or personal injury may result.
Leaving the screen fixed on a stationary image for an extended period of time may cause
afterimage burn-in or defective pixels.
Activate power-saving mode or a moving-picture screen saver if you will not be using
the product for an extended period of time.
Disconnect the power cord from the power socket if you do not plan on using the product
for an extended period of time (vacation, etc).
Dust accumulation combined with heat can cause a fire, electric shock or electric
leakage.
If a gas leakage is found, do not touch the product or power plug. Also, ventilate the area
immediately.
Use the product at the recommended resolution and frequency.
Sparks can cause an explosion or fire.
Do not use or keep combustible spray or an inflammable substance near the product.
Looking at the screen too close for an extended period of time can deteriorate your
eyesight.
An explosion or fire may result.
Rest your eyes for more than 5 minutes for every 1 hour of product use.
Your eyesight may deteriorate.
Eye fatigue will be relieved.
Store small accessories out of the reach of children.
7
Precautions for Use
Be careful that if you use the supplied pen with a load exceeding 2.5 kg, scratches may occur on the
protective glass.
If you use a ballpoint pen other than the supplied pen, be careful that the screen may be stained
with ink or damaged.
Do not use a dirty brush to avoid screen damage.
"" We recommend that you use the supplied pen. Do not use sharp, pointed objects other than
the pen.
"" If dust or dirt from the supplied pen remains on the protective glass, clean it referring to
the instructions below.
Cleaning the exterior and display
Wipe the surface with a slightly wet, soft cloth, and then wipe with a dry cloth.
1
2
3
8
Chapter 02
Preparations
Checking the Components
"" Contact the vendor where you
purchased the product if any
components are missing.
Quick Setup Guide
"" The appearance of the components
may differ from the images shown.
Warranty card
(Not available in some locations)
Regulatory guide
Power cord
Cover Terminal, Screw (M4 x
L10) x 2
Cover Cable, Screw (M4 x L10)
"" Refer to the installation guide for the
WMR stand or wall amount (available
for optional purchase).
USB cable
Touch Pen x 2
9
Parts
"" The colour and shape of parts may differ from what is shown. Specifications are subject to change without
notice to improve quality.
Parts
Description
Power button
•• Press and hold the button to turn off the product.
•• In writing mode, shortly press the Power button to switch to the screen saver mode.
•• The pen is magnetic. Keep it by attaching to the marked location.
""
: WM55R,
: WM65R
Power indicator
Power button
Speaker
10
Ports
"" The colour and shape of parts may differ from what is shown. Specifications are subject to change without
notice to improve quality.
Ports
USB
(1.0A)
LAN
USB
Description
(1.0A)
"" The USB ports on the product accept a maximum constant current of 1.0A. If the
maximum value is exceeded, USB ports may not work.
LAN
SERVICE
HDMI IN 2
SERVICE
Dedicated to service technicians.
"" This port is for servicing only and has no user function. Do not connect a cable to
this port.
HDMI IN 2
AUDIO
OUT
Connects to a network using a LAN cable. (10/100 Mbps)
"" Use Cat7(*STP Type) cable for the connection.
*Shielded Twist Pair.
HDMI IN 1
TOUCH
OUT
Connect to a USB memory device.
Connects to a source device using a HDMI cable.
HDMI IN 1
TOUCH OUT
Allows touch-based control of the PC screen connected through the HDMI IN 1 or HDMI
IN 2 port. Use a USB cable to connect between the TOUCH OUT port on the rear of the
product and the PC.
AUDIO OUT
Outputs sound to an audio device via an audio cable.
11
Tray (optional purchase)
"" Trays are sold separately. Contact your vendor for assistance to make a purchase.
"" The colour and shape of parts may differ from what is shown. Specifications are subject to change without
notice to improve quality.
Ports
Description
USB
Connect to a USB memory device.
USB IN
Provides USB connectivity to PC.
USB OUT
1 Use an USB cable between the USB OUT port on the product and a USB port on a PC
to connect them.
2 Insert an USB storage device to the USB IN port.
3 You can check the USB device connected to the tray from the PC.
TOUCH OUT
Allows touch-based control of the PC screen connected through the HDMI IN 3 port.
Use a USB cable to connect between the TOUCH OUT port on the tray and the PC.
HDMI IN 3
An HDMI port for displaying input from an external source.
SCREEN SHARE
An HDMI port for connecting to an external display.
•• Tag your mobile device to the NFC pad for connection.
"" In writing mode, an NFC tagging can automatically perform Smart View or
Screen Mirroring on your mobile device.
"" This function is supported only on Android 8.0 Oreo version or later of Samsung
mobile devices.
•• Tag an NFC card to the NFC pad to enter an email address automatically.
"" While creating an email, an email address is automatically entered if it is read
from the encoded NFC tag.
"" For how to enter an email address in the NFC card, refer to 'Sending Email'.
12
Before Installing the Product (Installation
Guide)
This product can be wall-mounted. The exclusive Samsung stand (for WM55R) and wall mount
(for WM65R) are available for optional purchase.
"" Do not install or use the product with its front facing up. Touch-based functions may not
work properly.
WM55R
Ventilation
"" Contact Samsung Customer Service Centre for further details.
Installation on a Perpendicular Wall
A Minimum 15 mm
B Ambient temperature: 35 ℃ or less
"" When installing the product on a perpendicular wall, allow at least 15
mm of space between the product and wall surface for ventilation and
ensure that the ambient temperature is kept below 35 °C.
A
Rotation
"" Contact Samsung Customer Service Centre for further details.
•• To use the product in landscape mode, turn it anticlockwise and make sure the power
indicator is on the right after turning.
B
Installation on an Indented Wall
A Minimum 15 mm
B Minimum 25 mm
B
C Ambient temperature: 35 ℃ or less
"" When installing the product on an indented wall, allow at least the
space specified above between the product and wall for ventilation and
ensure that the ambient temperature is kept below 35 °C.
A
B
C
13
WM65R
Ventilation
"" Contact Samsung Customer Service Centre for further details.
Installation on a Perpendicular Wall
A Minimum 0 mm
B Ambient temperature: 35 ℃ or less
A
B
Installation on an Indented Wall
A Minimum 0 mm
B Minimum 25 mm
B
C Ambient temperature: 35 ℃ or less
"" When installing the product on an indented wall, allow at least the
space specified above between the product and wall for ventilation and
ensure that the ambient temperature is kept below 35 °C.
A
B
C
14
Installing the Wall Mount
Installing the Wall Mount
•• The wall mount kit allows you to mount the product on the wall.
•• For detailed information on installing the wall mount, see the instructions provided with the wall mount.
•• We recommend you contact a technician for assistance when installing the wall mount bracket.
•• Samsung Electronics is not responsible for any damage to the product or injury to yourself or others if you select to install the wall mount on your own.
Wall Mount Kit Specifications (VESA)
•• Samsung wall mount kits contain a detailed installation manual and all parts necessary for assembly are
provided.
"" Install your wall mount on a solid wall perpendicular to the floor.
To install the product on the other wall area, contact the nearest
agency.
•• Do not use screws that are longer than the standard length or do not comply with the VESA standard screw
specifications. Screws that are too long may cause damage to the inside of the product.
If you install the product on a slanted wall, it may fall and result in
severe personal injury.
•• For wall mounts that do not comply with the VESA standard screw specifications, the length of the screws may
differ depending on the wall mount specifications.
•• Do not fasten the screws too firmly. This may damage the product or cause the product to fall, leading to
personal injury. Samsung is not liable for these kinds of accidents.
•• Samsung is not liable for product damage or personal injury when a non-VESA or non-specified wall mount is
used or the consumer fails to follow the product installation instructions.
•• Always have at least two people mount the product on a wall.
•• Standard dimensions for wall mount kits are shown in the table below.
Model Name
VESA screw hole specs (A * B) in
millimeters
Standard Screw
Quantity
400 × 400
M8
4
WM55R
WM65R
"" Do not install your Wall Mount Kit while your product is turned on. It may result in personal injury due to electric
shock.
15
Connecting to a network
•• Depending on how your network is configured, you may be able to attach your product to
your LAN by connecting the LAN port on the back of your product directly to a network wall
outlet using a LAN cable.
See the diagram below. Note that the wall outlet is attached to a modem or router
elsewhere in your house.
Network Settings (Wired)
LAN
The Modem Port on the Wall
RJ45
Connecting to a Wired Network
There are three ways to attach your product to your LAN using cable.
•• You can attach your product to your LAN by connecting the LAN port on the back of your
product to an external modem using a LAN cable. See the diagram below.
External Modem
The Modem Port on the Wall
(ADSL / VDSL)
Modem Cable
RJ45
LAN Cable
•• You can attach your product to your LAN by connecting the LAN port on the back of your
product to an IP Sharer which is connected to an external modem. Use LAN cable for the
connection. See the diagram below.
The Modem Port on the Wall
External Modem
IP Sharer
(ADSL / VDSL)
(having DHCP server)
Modem Cable
LAN Cable
LAN Cable
LAN
LAN
RJ45
If you have a Dynamic Network, you should use an ADSL modem or router that supports
the Dynamic Host Configuration Protocol (DHCP). Modems and routers that support DHCP
automatically provide the IP address, subnet mask, gateway, and DNS values your product
needs to access the Internet so you do not have to enter them manually. Most home networks
are Dynamic Networks.
Some networks require a Static IP address. If your network requires a Static IP address, you
must enter the IP address, subnet mask, gateway, and DNS values manually on your product
Cable Setup Screen when you set up the network connection. To get the IP address, subnet
mask, gateway, and DNS values, contact your Internet Service Provider (ISP).
If you have a Windows computer, you can also get these values through your computer.
"" You can use ADSL modems that support DHCP if your network requires a Static IP address.
"" ADSL modems that support DHCP also let you use Static IP addresses.
LAN Cable
16
Set the network connection to use Internet services such as perform software upgrades.
Automatic Open Network Settings (Wired)
Connect to the network using a LAN cable.
How to set up manually
1 Set Network Type to Wired from the Open Network Settings page.
2 The network test screen appears and the verification process starts. Press Cancel. The
verification process stops.
Make sure a LAN cable is connected first.
3 Select IP Settings on network connection screen. The IP Settings screen appears.
How to set up automatically
4 Select the field at the top and then set IP setting to Enter manually Repeat the entry
1 Set Network Type to Wired from the Open Network Settings page.
process for each field in the IP Address.
2 The network test screen appears and verifies the network connection.
"" Setting IP setting to Enter manually automatically changes DNS setting to Enter
manually.
When the connection has been verified, the “Success! Your device is connected to the
Internet. If you have any problems using online services, please contact your Internet
service provider.” message appears.
"" If the connection process fails, check the LAN port connection.
"" If the automatic process cannot find the network connection values or if you want to set the
connection manually, go to the next section(Manual Open Network Settings (Wired)).
5 When done, select OK at the bottom of the page. The network test screen appears and the
verification process starts.
6 When the connection has been verified, the “Success! Your device is connected to the
Internet. If you have any problems using online services, please contact your Internet
service provider.” message appears.
Manual Open Network Settings (Wired)
Offices may use static IP addresses.
If this is the case, ask the network administrator for the IP address, subnet mask, gateway and
DNS server address. Enter these values manually.
Getting the Network Connection Values
To view the Network connection values on most Windows computers, follow these steps.
1 Right click the Network icon on the bottom right of the screen.
2 In the pop-up menu that appears, click Status.
3 On the dialog that appears, click the Support tab.
4 On the Support Tab, click the Details button. The Network connection values are displayed.
17
Network Settings (Wireless)
Connecting to a Wireless Network
Wireless IP sharer
(router having DHCP server)
The LAN Port on the Wall
Automatic Network Setup (Wireless)
Most wireless networks have an optional security system that requires devices that access the
network to transmit an encrypted security code called an Access or Security Key. The Security
Key is based on a Pass Phrase, typically a word or a series of letters and numbers of a specified
length you were asked to enter when you set up security for your wireless network. If you use
this method of setting up the network connection, and have a Security Key for your wireless
network, you will have to enter the Pass Phrase during the the automatic or manual setup
process.
How to set up automatically
1 Set Network Type to Wireless from the Open Network Settings page.
2 The Network function searches for available wireless networks. When done, it displays a list
LAN Cable
Samsung recommends using IEEE 802.11n. When you play video over a network connection, the
video may not play smoothly.
"" Select a channel for the wireless IP sharer that is not currently being used. If the channel set
for the wireless IP sharer is currently being used by another device nearby, this will result in
interference and communication failure.
"" Your product supports only the following wireless network security protocols.
If you select the Pure High-throughput (Greenfield) 802.11n mode and the Encryption type is
set to WEP, TKIP or TKIP AES (WPS2Mixed) on your AP or wireless router, Samsung products
will not support a connection in compliance with new Wi-Fi certification specifications.
"" If your wireless router supports WPS (Wi-Fi Protected Setup), you can connect to the
network via PBC (Push Button Configuration) or PIN (Personal Identification Number). WPS
will automatically configure the SSID and WPA key in either mode.
"" Connection Methods: You can setup the wireless network connection in three ways.
Auto Setup (Using the Auto Network Search function), Manual Setup, Use WPS
"" This product supports Enterprise WPA2 (TLS/TTLS/PEAP).
of the available networks.
3 In the list of networks, select a network.
"" If the desired wireless router does not appear, select Refresh to search again.
"" If the router cannot be found after retrying, select the Add Network.
4 If the Enter the password for (AP Name). screen appears, go to step 5. If you select a
wireless router that does not have security, go to step 7.
5 If the router has security, enter the Enter the password for (AP Name). (Security key or PIN).
6 When done, select Done. The network connection screen appears and the verification
process starts.
"" A connection with the router is established, but the Internet cannot be accessed. In this
case, contact your Internet service provider.
7 When the connection has been verified, the “Success! Your device is connected to the
Internet. If you have any problems using online services, please contact your Internet
service provider.” message appears.
18
Manual Network Setup (Wireless)
How to set up manually
Offices may use static IP addresses.
1 Set Network Type to Wireless from the Open Network Settings page.
If this is the case, ask the network administrator for the IP address, subnet mask, gateway and
DNS server address. Enter these values manually.
Getting the Network Connection Values
To view the Network connection values on most Windows computers, follow these steps.
1 Right click the Network icon on the bottom right of the screen.
2 In the pop-up menu that appears, click Status.
3 On the dialog that appears, click the Support tab.
4 On the Support Tab, click the Details button. The Network connection values are displayed.
2 The Network function searches for available wireless networks. When done, it displays a list
of the available networks.
3 In the list of networks, select a network.
"" If the desired wireless router does not appear, select Refresh to search again.
"" If the router cannot be found after retrying, select the Stop button.
The Add Network button appears.
4 If the Enter the password for (AP Name). screen appears, go to step 5. If you select a
wireless router that does not have security, go to step 7.
5 If the router has security, enter the Enter the password for (AP Name). (Security key or PIN).
6 When done, select Done. The network connection screen appears and the verification
process starts.
7 Select Cancel while network connections are being attempted. This will stop the
connection.
8 Select IP Settings on network connection screen. The IP Settings screen appears.
9 Select the field at the top and then set IP setting to Enter manually. Repeat the entry
process for each field in the IP Address.
"" Setting IP setting to Enter manually automatically changes DNS setting to Enter
manually.
10 When done, select OK at the bottom of the page. The network test screen appears and the
verification process starts.
11 When the connection has been verified, the “Success! Your device is connected to the
Internet. If you have any problems using online services, please contact your Internet
service provider.” message appears.
19
Use WPS
How to set up using Use WPS
If your router has a Use WPS button, follow these steps.
1 Set Network Type to Wireless from the Open Network Settings page.
2 Select Use WPS.
3 Press the WPS or PBC button on your wireless router within the next two minutes. Your
product automatically acquires all the network setting values it needs and connects to your
network.
4 The network connection screen appears, and network setup is done.
20
Chapter 03
Writing
What's a 'Roll'?
•• Files are called 'rolls' in this product. A 'roll' is a file with multiple pages linked together.
•• A roll can have up to 20 pages linked together.
"" BRUSH MODE supports one page only.
•• Pages are linked horizontally in landscape orientation, and vertically in portrait orientation.
"" You can open only one roll on one screen. For more information, refer to 'Managing Rolls'.
Landscape orientation
Portrait orientation
Page 1
Page 2
Page 1
Page 2
21
PEN MODE
Buttons
Screen Elements
Description
IMPORT
View the screen of a mobile device or PC connected to the product, or import data
such as images from a connected USB or network drive.
EXPORT
Share your creations in various ways.
Manage and change the rolls and settings.
IMPORT
EXPORT
Move or edit the created rolls for each page.
Create a layer to write or draw on over the screen which can also be saved the
captured image.
Select and edit / capture / email / print the pen or brush content.
Undo or redo the last action.
•• If any page editing actions such as page adding, deleting, and moving are
is reset.
found,
""
can be performed up to 20 times for each individual.
Close the current roll and create a new roll.
Page breaking line
See page lines.
Scroll through pages.
Bezel Scroll
Scroll the black area to move the pages.
22
Drawing
Changing the pen thickness and colour
You can freely use the supplied pen to write anything you
want.
•• Thin Tip (
•• Thick Tip (
You can change the pen colour by touching and holding the screen with the pen.
): Pen Type
): Highlighter Type
Erasing
You can use your finger or palm to erase your writing.
23
BRUSH MODE
Screen Elements
IMPORT
EXPORT
Buttons
Description
IMPORT
View the screen of a mobile device or PC connected to the product, or import data such as
images from a connected USB or network drive.
EXPORT
Share your creations in various ways.
Manage and change the rolls and settings.
Select and edit / capture / email / print the pen or brush content.
Undo or redo the last action.
•• If any page editing actions such as page adding, deleting, and moving are found,
is reset.
""
can be performed up to 5 times for each individual.
Close the current roll and create a new roll.
"" Changes in the thickness depending on the area touching the screen apply immediately. (max. 2 cm)
"" Brush use is recommended.
"" BRUSH MODE supports single touch only.
24
Changing the brush colour
After touching the palette on the screen, you can draw a picture by selecting the desired mode
during watercolors and emulsifications.
WATER
OIL
: Dry colours to stop blending.
: Extract the colour from the selected point.
: Delete the selected area.
25
Managing Rolls
Buttons
Description
NEW
Create a new roll.
SAVE
Save the current roll.
ROLLS
Open, delete or export saved rolls.
PEN MODE / BRUSH
MODE
Choose a mode.
FORMS
Change the background format.
"" This menu is only visible in PEN MODE mode.
NEW
SAVE
LOCK / UNLOCK
ROLLS
•• UNLOCK: To unlock a locked roll, press the six-digit password you set when locking the
roll.
BRUSH MODE
FORMS
"" Once unlocked, the current roll remains unlocked until it is locked again.
LOCK
VOLUME
•• LOCK: Press a six-digit password to lock the current roll.
VOLUME
Adjust the volume.
SETTINGS
You can see the configuration menu.
HOW TO USE
You can view How To Use.
SETTINGS
HOW TO USE
26
ROLL EXPLORER
Deleting / Exporting rolls
→ Rolls
→ Rolls → Select
Open, browse and manage rolls via the Rolls explorer.
You can select multiple rolls to export or delete.
Rolls
All
By name
By date
Select
Select
KED
LOC
KED
KED
KED
LOC
KED
LOC
KED
LOC
KED
LOC
KED
KED
KED
LOC
KED
KED
LOC
KED
LOC
KED
KED
KED
KED
KED
KED
LOC
LOC
LOC
LOC
LOC
LOC
KED
LOC
KED
LOC
LOC
KED
LOC
KED
KED
LOC
LOC
KED
LOC
LOC
KED
KED
LOC
LOC
KED
KED
KED
LOC
LOC
KED
KED
KED
KED
KED
KED
KED
LOC
LOC
LOC
LOC
LOC
LOC
KED
LOC
KED
KED
KED
LOC
KED
LOC
KED
LOC
KED
LOC
KED
LOC
LOC
KED
LOC
KED
LOC
KED
LOC
KED
LOC
LOC
KED
LOC
KED
LOC
KED
LOC
KED
KED
LOC
KED
LOC
KED
LOC
LOC
KED
LOC
LOC
KED
LOC
LOC
KED
LOC
LOC
KED
KED
LOC
KED
LOC
LOC
KED
LOC
KED
LOC
KED
KED
LOC
KED
KED
LOC
KED
LOC
KED
LOC
KED
KED
LOC
KED
LOC
KED
KED
LOC
KED
LOC
KED
LOC
KED
Cancel
LOC
KED
KED
LOC
KED
LOC
KED
Delete
KED
LOC
KED
LOC
KED
LOC
KED
LOC
KED
LOC
KED
LOC
KED
LOC
LOC
KED
LOC
KED
LOC
KED
LOC
KED
LOC
KED
LOC
KED
LOC
KED
LOC
KED
LOC
KED
LOC
Export
LOC
LOC
LOC
LOC
LOC
LOC
LOC
Parts
All
Description
You can view the list by the mode you want.
•• All / Pen Mode / Brush Mode
By name ↔ By date
Set the sort order of files.
Select
Select multiple rolls to export or delete.
File Name
Rename the file.
Rolls
Browse and open a desired roll.
Parts
Export
Description
Share the selected rolls any way you like.
•• Email(
) / USB( ) / Network Drive(
Delete
Delete the selected rolls.
Cancel
Deselect the roll.
)
"" To open a locked roll ( ), press the six-digit password.
"" The rolls are sorted by recent date.
27
Page Viewer
"" This menu is only visible in PEN MODE mode.
Parts
Page number
Focus
You can move or edit the created rolls for each page.
IMPORT
Description
Displays the page number.
Displays the page you are currently viewing.
•• When you tap a page, the focus is moved to it.
Delete the focused page.
EXPORT
Add a new page to the focused position.
"" You can create up to 20 pages per roll.
01
02
03
04
05
Page viewer area
28
Note On/Off
Add a layer over the screen to write or draw on. This can be useful for adding
note to content from an external source.
"" This menu is only visible in PEN MODE mode.
1 Tap to add a new note layer over the screen.
2 Take note on the layer.
3 Tap
and close.
•• Save / Don't Save / Cancel
29
Using the Selection Tools
Rotation
Resize
Move
Select and edit / capture / email / print the pen or brush content. Use
move, rotate, or resize the selection.
to
EDIT
Resize
Capture / email / print
1 Tap
in the screen bottom. A select box appears on the screen.
"" Drag the
of the select box to adjust the size.
2 Select the area and choose from
/
/
options.
"" The product must be connected to a network to use the email or print option.
Editing pen and brush content
"" The changes apply to pen and brush content only.
1 Tap
in the screen bottom. A select box appears on the screen.
"" Drag the
2 Tap
of the select box to adjust the size.
to enable editing for the selected area.
3 Move, rotate or resize the selected area and tap
"" Tap
.
to abort the changes.
30
Chapter 04
IMPORT
You can view the screen of a mobile device or PC connected to the product, or import data such
as images from a connected USB or network drive.
•• Touch IMPORT at the top of the screen to select the desired device.
Icons
Description
Displays the screen from a mobile device by using Smart View or Screen
Mirroring function.
Displays your PC screen imported using HDMI connection or WiFi display.
IMPORT
Import images, native FLIP files, and documents from a USB device.
Import images, native FLIP files, and documents from a network drive.
MOBILE
PC
IMPORT
USB
EXPORT
NETWORK DRIVE
"" The native FLIP format (.iwb) refers to files that are directly saved from the device and only
supported by FLIP devices.
"" Supportable image file formats: JPG, BMP, PNG, MPO
"" Supported document file formats: DOC, PPT, PDF, XLS, XLSX
31
Connecting to a Mobile Device
IMPORT → MOBILE
Connecting using Smart View or Screen Mirroring
Connecting using NFC tagging
"" This feature is only available when the product is equipped with a tray (optional purchase).
"" This function is supported only on Android 8.0 Oreo version or later of Samsung mobile
devices.
"" In writing mode, an NFC tagging can automatically perform Smart View or Screen Mirroring
on your mobile device.
Smart View
1 Drag down the top bar on the mobile device screen to start Smart View or Screen Mirroring.
2 Select this product from the list of devices displayed on the screen.
–– The initial device name is [FLIP] Samsung WMR Series.
"" You can control the mobile device from the product screen.
1 Turn on the NFC feature on a supported mobile device.
2 Tag the mobile device to the NFC pad.
"" You can control the mobile device from the product screen.
"" HDCP (High-bandwidth Digital Content Protection) contents will not show on the screen if
PIP Capture is set to On.
32
Connecting to a PC
Connecting via the WiFi Display function
"" This function is only available for the PC that support the WiFi Display function.
IMPORT → PC
IMPORT
MOBILE
USB
PC
NETWORK DRIVE
PC
STEP. 02
HDMI 1
HDMI 2
HDMI 3
Wireless
Remote PC
STEP. 01
"" HDMI 3 is available when the product is equipped with a tray (optional purchase).
Connecting using a cable
1 Connect the product to the PC using an HDMI cable.
"" HDCP contents will not show on the screen if PIP Capture is set to On.
HDMI IN
1 Select Action Center or Devices in the taskbar notification area of the PC.
2 Click Connect or Project and select a [Flip] Samsung WMR Series device to complete the
connection.
"" The connection procedure may vary depending on the PC.
"" After the WiFi Display connection is made, you can control the PC screen from the product
screen.
"" This function is only supported by Windows 10.
2 Select IMPORT → PC → HDMI from the top of the screen.
3 To control the PC from the product screen, connect the supplied USB cable to the TOUCH
OUT port on the product.
"" If used in a multi-screen setup, make sure you have configured FLIP as the main display.
TOUCH OUT
33
Importing from a USB Device
Importing from a Network Drive
IMPORT → USB
IMPORT → NETWORK DRIVE
IMPORT
IMPORT
MOBILE
PC
USB
USB
USB1
MOBILE
NETWORK DRIVE
PC
USB
NETWORK DRIVE
NETWORK DRIVE
USB2
NETWORK1
NETWORK2
Add
Connect an external HDD or a USB storage device.
Connect the network drive to bring files.
"" Import images, native FLIP files (.iwb), and documents.
"" You can register a network drive while the network is connected.
For information about how to connect to a network, see 'Connecting to a network'.
"" You can register a network drive account at � → SETTINGS → Connect → Advanced
Settings → Network Drive → Add Account.
To register a network drive account, you must enter the Address, Username, and Password.
To register your network drive account, refer to 'Add Account' for Network Drive.
"" Import images, native FLIP files (.iwb), and documents.
34
Source Window
When you connect a PC or a mobile device to the product, the source window appears.
Parts
Device name
Description
Menu bar
Drag the source window to move to the desired position.
Device name
Displays the name of the connected device.
Capture the source window.
"" This feature is not available when PIP Capture is set to Off.
Rotate the source window.
"" This function is supported only on Android 8.0 Oreo version or later of Samsung
mobile devices.
Change the input screen position or view it on full screen.
/
/
/
/
••
"" When the product is in portrait orientation, the full screen mode is supported
only on the Android 8.0 Oreo version or later of Samsung mobile devices.
Close the source window.
Adjust the size of the source window.
35
Document view
Displays the document file you select to import from a USB device or network drive.
"" Supported document file formats: DOC, PPT, PDF, XLS, XLSX
Parts
File name
Description
Menu bar
Drag the menu bar to move the viewer around.
File name
Name of the currently viewing file.
Capture the viewer screen.
Change the input screen position or view it on full screen.
••
/
/
/
/
Close the viewer.
Tap
or
to move between pages.
Adjust size of the viewer.
9/11
36
Image view
Select the file to import from the USB device or network drive.
Parts
File name
Description
Menu bar
Drag the menu bar to move the viewer around.
File name
Name of the currently viewing file.
Tap
to paste the image to the roll.
Rotate the image.
Change the input screen position or view it on full screen.
••
/
/
/
/
Close the source window. Close the viewer.
Adjust size of the viewer.
37
Chapter 05
EXPORT
You can export your created rolls in various ways.
Icons
Description
Send your created rolls via email.
EXPORT
Print your created rolls.
Export your created rolls to a connected USB device.
EMAIL
PRINT
USB
SCREEN SHARE
NETWORK DRIVE
MOBILE
Share your screen with selected devices.
IMPORT
EXPORT
Export your created rolls to a registered and connected network drive.
Send the roll to a mobile device.
38
Sending Email
To send your created rolls via email, first register your email account.
"" You can register your email account at � → SETTINGS → Connect → Advanced Settings → Email.
EXPORT → EMAIL
EMAIL
To
Subject
1
Send
*****@***. ***
[FLIP] Samsung WMR Series ****-**-**, **:**
2
"" If you set Sender Authentication to Personal Account at � → SETTINGS → Connect → Advanced Settings →
Email, you must authenticate your account each time you send an email. See below.
–– You can send emails when Sender Authentication is set to Personal Account as long as you have an account
on that mail server (SMTP Server Name and SMTP Port Number).
Note that it requires the sender to provide the SMTP account ID and password, as well as the sender address
for every email.
–– If you set Sender Authentication to Default Account, you can use the SMTP ID and password you saved
to Default Account to send emails. (The sender address is usually identical to the SMTP ID, with some
exceptions depending on the SMTP server.)
–– For the SMTP information required to register a mail server, contact your mail server administrator.
"" Files saved as dedicated files are converted to PDF files and sent.
Parts
Description
Enter the recipient's email address.
•• Press and type text by using the virtual keyboard.
"" Press on the virtual keyboard to enter text by handwriting.
To
"" Search recipient in Local Address Book or LDAP server.
"" Equip the product with a tray (optional purchase) to automatically enter the
address by tagging an NFC card or sticker containing the information.
: Explains where to tag the NFC card.
––
–– Using the NFC Writing App in mobile device or PC, etc, register an email
address with the NDEF Standard <Text> Record Type to an NFC Forum Type 2
Card sold on the market.
Subject
The email subject is automatically set to the device name and the current date.
Send
Send the email.
Change the page view mode for the roll to send.
Select the pages to send.
39
Printing
Installing Flip Printing Software
Follow the onscreen instructions to install Flip Printing Software.
To print, you must set up the Print Server and the Clock Set.
To set up the Print Server, the product and the printer you want and your PC must be connected
to the same network.
"" The installation takes about 10 minutes, and the time taken may vary depending on your PC
environment.
Flip Printing Software must be also installed on the PC connected.
PC installation requirements
"" For information about how to connect to a network, see 'Connecting to a network'.
•• Supported operating systems:
Windows 7(32/64 bit), Windows 10(32/64 bit), MAC
"" You can set up the Print Server at � → SETTINGS → Connect → Advanced Settings → Print
Server.
"" You can set Clock Set at � → SETTINGS → System → Time → Clock Set.
"" The Flip Printing Software is available on the website
– http://displaysolutions.samsung.com
– http://www.samsung.com
"" Devices that transfer files, such as virtual printers (PDF, XPS, One note, etc.) or fax
machines, are not supported, but only printers that can print actual paper are supported.
"" For print paper size, only A4 is supported.
"" When installing the software, make sure that critical Windows updates are already
installed. Update Windows to the latest version before beginning the setup.
"" For Windows 7, make sure that Service Pack 1 is already installed.
Setting up the printer
After the Flip Printing Software is installed, make the following settings on the product
onscreen menu.
Setting up automatically
1 Select � → SETTINGS → Connect → Advanced Settings menu.
2 Select Print Server → Connect to Server → Auto.
Setting up manually
1 Select � → SETTINGS → Connect → Advanced Settings menu.
2 Select Print Server → Connect to Server → Manual, and then enter the Server IP address of
the PC where Flip Printing Software is installed.
40
EXPORT → PRINT
Parts
PRINT
Print
Description
Printer
Displays a list of connected printers. Select a printer to print the roll with.
Copies
Set the number of prints.
Print preview area
Preview the roll to print.
Print
Start the printing.
Colour Mode
Select the colour to print the roll with.
Printer
Copies
1
Colour Mode
01
2
Change the page view mode of the roll to print.
Select the pages to print.
41
Exporting to a USB Device
EXPORT → USB
EXPORT
EMAIL
PRINT
USB
SCREEN SHARE
NETWORK DRIVE
USB
USB1
MOBILE
SAVE
USB2
Connect an external HDD or a USB storage device.
"" Your device saves files in two versions (IWB and PDF formats).
42
Sharing your screen
Share your screen with selected devices.
EXPORT → SCREEN SHARE
1 Use an HDMI cable to connect the PC to the HDMI IN port on the product or tray (optional
Connecting with HDMI cables
purchase).
2 Use an HDMI cable to connect the display to the SCREEN SHARE port.
EXPORT
EMAIL
PRINT
SCREEN SHARE
USB
SCREEN SHARE
NETWORK DRIVE
MOBILE
SAVE
3 From the top of the screen, select EXPORT → SCREEN SHARE → Wired.
"" If the PC is connected to the HDMI IN 3 port on a tray (optional purchase) without
setting it, the PC screen is shared on the display instead.
4 The screen is shared on the display.
Wired
Wireless
"" This option supports UHD (50 Hz / 60 Hz) and FHD (50 Hz / 60 Hz) only.
"" The screen may blink once or twice upon when connecting for the first time or when there
is a change in the WMR product or source state.
Connecting wirelessly
From the top of the screen, select EXPORT → SCREEN SHARE → Wireless and then the device to
share the screen with.
"" SCREEN SHARE feature works best when using FLIP in landscape orientation.
"" Devices must support Screen Mirroring in order to use SCREEN SHARE with.
Buttons
Description
Change Device
Change devices to share the screen with.
Disconnect
Stop sharing.
43
Exporting from a Network Drive
Sending to a mobile device
EXPORT → NETWORK DRIVE
EXPORT → MOBILE
View the screen of the product from a mobile device.
EXPORT
EMAIL
PRINT
USB
SCREEN SHARE
NETWORK DRIVE
MOBILE
NETWORK DRIVE
"" Sharing is only available for rolls at the moment.
Download Samba client to your mobile device and enter the following information which can
be found on the product screen.
•• Wi-Fi Name, Wi-Fi Password, Server IP address
NETWORK1
NETWORK2
Add
Connect the network drive to save files.
"" You can register a network drive while the network is connected.
For information about how to connect to a network, see 'Connecting to a network'.
"" You can register a network drive account at � → SETTINGS → Connect → Advanced
Settings → Network Drive → Add Account.
To register a network drive account, you must enter the Address, Username, and Password.
To register your network drive account, refer to 'Add Account' for Network Drive.
"" Your device saves files in two versions (IWB and PDF formats).
44
Chapter 06
Menu
→ SETTINGS
Connect
2nd
3rd
Network
Description
Configure your device's network.
Network Status
View your current network and internet status.
Open Network Settings
Configure network settings to connect to an available network.
WPA Certificate Manager
Manage the certificates installed on this device.
•• Install Certificate
•• Delete Certificate
External Device Manager
Reset Network
Restore the network settings to the factory default.
Input Device Manager
Set up keyboards to use with your Signage. You can add keyboards and configure their settings.
•• Bluetooth Device List
•• Keyboard Settings
•• Mouse Settings
Device Connect Manager
Allow devices on your network, like smartphones and tablets, to share content with your Signage.
•• Access Notification
•• Device List
45
2nd
3rd
Description
Advanced Settings
Email
Set up an email account for sending emails.
•• SMTP Server Name: SMTP server address
•• SMTP Port Number: SMTP server port
•• SSL/TLS: Enable or disable SSL/TLS
•• Sender Authentication: Choose the authentication mode to be used when sending emails
–– Personal Account / Default Account
•• Default Account: Default SMTP account
•• Password: Password for the default SMTP account
•• Sender Email: Sender's email address
•• Recipient Address: Select from options to manage email contacts after successfully send emails
–– Auto Save / Do Not Save / Delete All
•• Local Address Book: Import contacts from a USB device or delete them.
–– Import / Delete Local Address Book
"" For more information, refer to 'Importing Local Address Book contacts'.
46
Importing Local Address Book contacts
Using Local Address Book contacts
To use FLIP Local Address Book, first Import contacts from a CSV file using a USB device.
Automatically search and suggest from the list of contacts when selecting recipient(s) in
EXPORT → EMAIL.
1 Use LDAP: Set Don't Use.
� → SETTINGS → Connect → Advanced Settings → Enter password → LDAP → Set LDAP
Connection → Use LDAP → Don't Use
2 Set up details under Email menu.
� → SETTINGS → Connect → Advanced Settings → Enter password → Email
"" To use this function, complete setting details under Email menu.
Deleting Local Address Book contacts
� → SETTINGS → Connect → Advanced Settings → Enter password → Email → Local Address
Book → Delete Local Address Book
3 Edit and save your Local Address Book to a USB device.
Make a list of contacts in the following structure and save it to the root directory as
RecentSearchList.csv.
–– RecentSearchList.csv structure (example)
emailid1@samsung.com
Name1
Level1
Team1
Company1
emailid2@samsung.com
Name2
Level2
Team2
Company2
emailid3@samsung.com
Name3
Level3
Team3
Company3
4 Connect the USB device to FLIP to import contacts.
� → SETTINGS → Connect → Advanced Settings → Enter password → Email → Local Address
Book → Import
"" The USB device and its contents may not be detected properly if a USB extension cable
is used. (USB hubs are not supported.)
"" Do not remove the USB device while loading.
"" If more than two USB devices are connected, some of them may not be detected.
"" USB devices that require higher operating power need to be connected to the USB
(1.0A) port on the back.
"" The file system supports FAT, exFAT, and NTFS formats.
47
2nd
3rd
Description
Advanced Settings
Print Server
Set up the Print Server to use the printing function.
"" For more information, refer to 'Printing'.
•• Connect to Server
–– Auto: View and select one from a list of server IP addresses of the PCs where Flip Printing Software is installed,
available on the network.
–– Manual: Enter the Server IP address of the PC where Flip Printing Software is installed.
•• Server IP: Enter the Server IP address of the PC where Flip Printing Software is installed.
•• Server Port: Enter the Server Port address of the PC where Flip Printing Software is installed.
Network Drive
Add or edit network drive accounts. You can only add network drives by using Samba.
•• Add Account: Add new network drive accounts. Only Samba can be added to the network drive.
"" SAMBA 2.0 or later is supported. If you cannot connect to the network drive, update SAMBA to the latest version.
"" To register a network drive account, you must enter the Address, Username, and Password.
–– Address: //computer IP address/shared folder name
"" When entering an address, be sure to use / instead
of ₩ and \.
For example, if you share a folder named
"sharedfolder" on a PC with IP address of
12.34.56.789, enter "//12.34.56.789/sharedfolder"
as the address.
Add Account
Address
//12.34.56.789/sharedfolder
Username
DomainName\WindowsAccount
Password
********
–– Username: A Windows account with permissions to
the shared folder
"" When entering a domain, be sure to use ₩ or \.
For example, DomainName₩WindowsAccount
Save
Cancel
–– Password: The password you set for your Windows
account
•• Edit Account: Edit network drive accounts.
48
2nd
3rd
Description
Advanced Settings
LDAP
Set LDAP connection or configure connected LDAP queries.
•• Set LDAP Connection
Configure a new LDAP connection.
–– Use LDAP: Whether or not to use LDAP
–– Import Setup Value: Can fetch the following settings from LDAPConnectionConfig.txt stored on the USB(Password
excluded)
"" For more information, refer to 'How to create a text file for use of LDAP'.
–– Authentication Type: Kerberos, Anonymous or Basic whichever is supported by the LDAP server
–– User ID: DN(Distinguished Name) of the User ID that is used in the LDAP server
"" The format of User ID complies with the DN format of LDAP.
e.g. cn=admin, dc=myldap, dc=com
–– Password: Password that is used for authentication of the LDAP server
–– Server Address: IP or URL of the LDAP server
–– Server Port Number: Port number of the LDAP server
–– Base DN: Top DN that is to be used for search in the DIT(Directory Information Tree) when connecting the LDAP
–– SSL/TLS: Whether or not to use SSL/TLS
"" When SSL/TLS is set to be Use, the encrypted data communication is enabled.
–– Use Untrusted Certificates: Whether or not to allow untrusted certificates
"" The following menu is activated when setting the Authentication Type to Kerberos.
–– Kerberos Realm: Kerberos realm data
–– KDC Host: KDC Host URL
–– KDC Port: KDC Host port number
49
2nd
3rd
Description
Advanced Settings
LDAP
•• LDAP Query Configuration
Set the query for the connected LDAP.
–– UID: Change the user UID that is used in LDAP.
–– Email: Change the Email that is used in LDAP.
–– Name: Change the user name (common name) that is used in LDAP.
–– Last Name: Change the surname of the user that is used in LDAP.
–– Position: Change the title that is used in LDAP.
–– Company name: Change the company name that is used in LDAP.
–– Department: Change the department name that is used in LDAP.
–– Use Custom Query: Fetches the user defined query from LDAPQuery.txt (case sensitive) stored on the USB.
"" For more information, refer to 'How to create a text file for use of LDAP'.
"" Press the Reset button to restore the settings to the factory defaults.
"" When the mapping does not match, the search result does not include the attributes.
Server Network Settings
Set up your server network connection and related functions.
•• Connect to server : Connect to MagicInfo server.
•• Server Access : Allow or deny access to MagicInfo server.
•• Proxy server : Set up your proxy server connection and related functions.
50
How to create a text file for use of LDAP
The LDAP configuration basically consists of many long sentences.
(2) Allocation of values (VAL) for each key
During LDAP configuration, FLIP can be fetched using the text file to prevent typos and make a
batch setting.
User ID: Enter the User ID.
"" Input of file name and content should be case sensitive for correct operation.
Server Port Number: Enter the Port of the LDAP server.
•• Format of LDAPConnectionConfig.txt
(1) Example of the text file
User ID=cn=Manager, dc=example, dc=com
Server Address=123.456.789.012
Server Port Number=12345
Base DN=dc=samsung, dc=example, dc=com
SSL/TLS=Don't Use
Use Untrusted Certificates=Don't Use
Authentication Type=Basic
Server Address: Enter the IP or URL of the LDAP server.
SSL/TLS: Enter Use or Don't Use.
Use Untrusted Certificates: Enter Use or Don't Use.
Authentication Type: Enter Basic or Anonymous.
‒‒ The following three items will be added if you select Kerberos type verification.
Kerberos Realm: Fill in the Kerberos field (Example: MYLDAP.LDAP)
KDC Host: Enter the KDC Host URL (Example: krb1.myldap.com)
KDC Port: Enter the KDC Host Port (Example: 88)
"" If you select to use Kerberos type verification, use the original Kerberos User ID for
a User ID instead of User ID in DN(Distinguished Name) format. (Example: Mirko)
Kerberos Realm=MYLDAP.COM
KDC Host=krb1.myldap.com
KDC Port=88
51
•• Format of LDAPQuery.txt
(1) Example of the text file
UID=uid
Email=mail
Name=cn
Last Name=sn
Position=title
Company Name=o
Department=departmentNumber
Query=(|(mail=*<A>*)(cn=*<A>*))
(2) Allocation of values (VAL) for each key
1) Mapping part (all rows except the last)
‒‒Includes all rows except the last, in the order of UID, Email, Name, Last Name,
Position, Company name, and Department.
‒‒Values are mapped in the following manner.
On the left of "=" syntax is the name that is seen in the LDAP Query Configuration
menu (also on the left) and mapped to the values on the right side of "=" (the actual
LDAP Server attributes).
‒‒You can choose attributes to change values. For instance, you can change the rightside values without changing the left-side values.
2) Query part
‒‒<A> is the Keyword that is used for a Search.
‒‒The syntax for the Use Custom Query complies with the LDAP Query rule excluding
<A>.
For example, when <A> is included in the mail or cn attribute, you can create it as
follows.
Query=(|(mail=*<A>*)(cn=*<A>*))
52
System
2nd
3rd
Language
Rolls
Description
Change your Language settings.
Auto Save
Automatically save all data.
Delete All
Delete all data from the device, including locked data.
Period for Delete All
Set a regular reset interval at which all data on the internal storage will be deleted.
Time
Configure various time-related settings.
Clock Set
Set current date and time.
DST
Adjust clock for Daylight Saving Time.
"" Start Date, End Date and Time Offset are enabled only when DST is set to On.
Smart Security
Change PIN
The security provided to protect your display device and connected storage devices against viruses includes.
Scan
Inspect your display device and connected storage devices to check for viruses.
Isolated List
Check the list of items that have been isolated they contain viruses.
Change your 6-digit Personal Identification Number (PIN).
"" The default PIN number is 000000.
"" Change the PIN to keep your device secure.
Device Name
Enter Device Name.
You can find this name on the device being used over the network.
Sound Output
Select speakers for sound output.
53
2nd
3rd
Tap to turn on
Description
Turn Tap to Turn On on or off. Enables you to turn on the screen with just a tap.
•• Off / On
Advanced Settings
Configure advanced settings which includes USB Lock, Network Lock, and Delete All Files.
Enter your 6 digit PIN number. The default PIN number is "000000".
"" If you want to change the PIN number, use the Change PIN function.
"" Change the PIN to keep your device secure.
Screen Saver
Set up the sreensaver. The selected image can be used as a custom screensaver.
Screen Lock
Run Screen Lock.
"" Tap and hold the screen to release Screen Lock.
USB Lock
Set up a USB Lock. After setting up, the device will be restarted to apply the settings.
•• Off / Read-only / All On
Network Lock
Set up a Network Lock.
Auto Power Off
Choose how long the display will stay on before turning off after no user interaction is detected.
Remote Standby
Turn Remote Standby on or off. By activating this feature, the network connection is maintained when the product is turned
off.
PIP Capture
Turn PIP Capture on or off.
"" HDCP contents will not show on the screen if PIP Capture is set to On.
Power on Source Setting
Set the default source when turning on the power. By setting this, either Roll or Source is turned on at power on.
Auto Source Switching
Set Auto Source Switching. By activating this feature, newly connected sources are displayed automatically.
PIP Screen Default Size
Set the default size for the PIP screen.
•• Full Screen / Partial Screen
54
2nd
3rd
Description
Advanced Settings
Clone Product
Export this device's settings or import from other devices.
Self Diagnosis
Run self diagnosis on the email, LDAP, or print server. A USB storage device must be connected to run a self diagnosis.
"" You can download a detailed self-diagnosis report including information about emails, LDAP, print servers, and other
information saved to the product to a USB device.
Start Setup
Go through the initial setup steps like you did the first time you used this product.
55
Picture
2nd
3rd
Description
Backlight
Adjust backlight brightness to your preference. 100 is the brightest setting.
Colour Temperature
It sets colour temperature. The value and temperature increase simultaneously, so the ratio of blue colour rises.
(Range: 2800K - 16000K)
White Balance
Input Signal Plus
R-Gain / G-Gain / B-Gain / R-Offset /
G-Offset / B-Offset / Reset
Adjust the colour temperature of the picture so that white objects appear brighter.
Expands the input signal range for HDMI connections.
"" Supports resolutions up to 3840 x 2160 @ 60 Hz with Input Signal Plus expansion set to On.
Supports resolutions up to 3840 x 2160 @ 30 Hz with Input Signal Plus expansion set to Off.
Supported Resolutions for UHD Input Signals
Check the supported resolution for UHD input signals.
•• Resolution: 3840 x 2160p, 4096 x 2160p
If Input Signal Plus is set to Off
Frame rate (fps)
Colour Depth / Chroma Sampling
RGB 4:4:4
YCbCr 4:4:4
YCbCr 4:2:2
YCbCr 4:2:0
50 / 60
8 bit
-
-
-
O
If Input Signal Plus is set to On
Frame rate (fps)
Colour Depth / Chroma Sampling
RGB 4:4:4
YCbCr 4:4:4
YCbCr 4:2:2
YCbCr 4:2:0
50 / 60
8 bit
O
O
O
O
10 bit
-
-
O
O
12 bit
-
-
O
O
56
2nd
HDMI Black Level
3rd
Description
Adjust the black level to optimise the HDMI picture brightness and contrast.
"" This function is available only when the product is connected to a PC using an HDMI cable and the Source window is
turned on.
Reset Picture
Restore all picture settings to the factory default.
57
Support
2nd
3rd
Software Update
Description
Update the software installed on your product.
Update now
Update software by downloading update files.
–– Online update
"" Requires an internet connection.
–– Update with a USB device
After downloading the update file from the Samsung website and storing it on a USB device, connect the USB device
to the product to update.
"" Make sure you saved the update file in a top-level folder.
•• Current Version: This is the software version already installed in the product.
Auto update
Automatically start software updates once your device is powered off.
"" Requires an internet connection.
Contact Samsung
Contact information for assistance with your device.
"" Go to Contact Samsung and find the product Model Code and Software Version.
Reset All
It initializes all items in the total menu.
58
Chapter 07
Troubleshooting Guide
Problems and Solutions
"" Before calling Samsung Customer
Service Centre, test your product
as follows. If the problem persists,
contact Samsung Customer Service
Centre.
"" If the product is not turned on
or off when you operate the
buttons or motion sensor of the
product, you can turn it on or off
with the Samsung remote control
or Samsung remote control
application.
Source window (HDMI) issue
Blank spaces are found on all four sides of the screen when The blank spaces found on the screen have nothing to do with the product.
an HDMI cable is connected to the product and PC.
Blank spaces on the screen are caused by the PC or graphics card. To resolve the problem,
adjust the screen size in the HDMI settings for the graphics card.
If the graphics card settings menu does not have an option to adjust the screen size, update
the graphics card driver to the latest version.
(Please contact the graphics card or computer manufacturer for further details about how to
adjust the screen settings.)
The images on the screen look distorted.
Check the cable connection to the product.
The screen is not clear. The screen is blurry.
Set the resolution and frequency to the recommended level.
The screen appears unstable and shaky.
Check that the resolution and frequency of the PC and graphics card are set within a range
compatible with the product. Then, change the screen settings if required by referring to
'Preset Timing Modes'.
There are shadows or ghost images left on the screen.
59
Source window (HDMI) issue
White does not really look white.
Go to Picture and adjust the White Balance settings.
The product will turn off automatically.
Make sure the power cable is connected properly to the product and power outlet.
The screen display does not look normal.
Encoded video content may cause the display to appear corrupted in scenes featuring fast
moving objects such as in a sports event or action video.
Low signal level or low picture quality may cause the display to appear corrupted. This does not
mean the product is defective.
A mobile device within a distance of one-meter radius may cause static on analogue and digital
products.
The brightness and colour do not look normal.
From the menu, select � → SETTINGS → Support → Reset All to try resetting the screen.
The display looks unstable and then freezes.
The screen may freeze when a resolution other than the recommended resolution is used or
if the signal is not stable. To resolve the issue, change the PC resolution to the recommended
resolution.
The screen cannot be displayed in full screen.
If the source window is set to full screen mode while in portrait orientation, a black bar appears
at both the top and bottom.
Change to landscape orientation, and then switch the Source window to full screen mode.
60
Sound issue
There is no sound.
Check the volume.
The volume is too low.
Adjust the volume.
If the volume is still low after turning it up to the maximum level, adjust the volume on your PC
sound card or software programme.
Video is available but there is no sound.
If an HDMI cable is connected, check the audio output settings on the PC.
If a source device is used
•• Check the audio output settings for the source device.
(For example, if your monitor is connected to HDMI, you may need to change the audio
option of your video output device to HDMI.)
Reconnect the power cable to the device and then reboot the device.
There is static coming from the speakers.
Low signal level can cause corrupted sound.
There is audible sound when the volume is muted.
Audio settings for main speakers are separate from the internal speakers on the product.
Changing or muting the volume on the product does not affect an external amplifier(decoder).
61
Touch function issues
The icons can be touched but the drawings cannot.
Use the provided product-specific pen.
Touching does not work when HDMI connection is used.
Check whether the TOUCH OUT port on the product is connected to a USB port on the PC using
a USB cable.
•• HDMI IN 1 or HDMI IN 2 → TOUCH OUT on the rear of the product
•• HDMI IN 3 → TOUCH OUT on the tray
I use two pens, but they do not work well.
Make sure that there is enough space between the two pens at multi-touching.
Touches break, reaction speed gets slow, and so on.
Make sure that there are no foreign substances on the screen surface.
Check whether the screen is broken.
Make sure that the product is not exposed to direct sunlight.
62
Other issue
The product smells like plastic.
The plastic smell is normal and disappears over time.
Small particles are found on the edges of the product.
The particles are part of the product design. The product is not defective.
When I try to change the PC resolution, a message "The
defined resolution is not supported." appears.
The message "The defined resolution is not supported." appears if the input source resolution
exceeds the maximum resolution of the product.
To resolve the issue, change the PC resolution to a resolution supported on the product.
There is no sound from the speakers in HDMI mode when a
DVI-HDMI cable is connected.
DVI cables do not transmit sound data.
HDMI Black Level is not functioning properly on an HDMI
device with YCbCr output.
This function works only when the HDMI signal of the external device is RGB output.
There is no sound in HDMI mode.
Displayed picture colours may not look normal. Video or sound may not be available. This can
occur if a source device that only supports an older version of the HDMI standard is connected
to the product.
63
Chapter 08
Specifications
General
"" Horizontal Frequency
The time required to scan a single
line from the left to the right side
of the screen is called a horizontal
cycle. The reciprocal number of a
horizontal cycle is called horizontal
frequency. Horizontal frequency is
measured in kHz.
"" Vertical Frequency
The product displays a single image
multiple times per second (like a
fluorescent light) to display what
the viewer sees. The rate of a single
image being displayed repeatedly per
second is called vertical frequency
or refresh rate. Vertical frequency is
measured in Hz.
Model Name
Panel
Synchronization
Resolution
WM55R
WM65R
Size
55 CLASS (54.6 inches / 138.7 cm)
65 CLASS (64.5 inches / 163.9 cm)
Display area
1209.6 mm (H) x 680.4 mm (V)
1428.48 mm (H) x 803.52 mm (V)
Horizontal Frequency
30 - 90 kHz
Vertical Frequency
24 - 75 Hz
Optimum resolution
3840 x 2160
Maximum resolution
Power Supply
AC100-240V~ 50/60Hz
Refer to the label at the back of the product as the standard voltage can vary in different countries.
Environmental
considerations
Operating
Temperature : 0 °C – 40 °C (32 °F – 104 °F)
* For installing the enclosure, keep the internal temperature at 40 °C or below.
Humidity : 10% – 80%, non-condensing
Storage
Temperature : -20 °C – 45 °C (-4 °F – 113 °F)
Humidity : 5% – 95%, non-condensing
* Applicable before the product package is unpacked.
64
"" Due to the nature of the manufacturing of this product, approximately 1 pixel per million (1ppm) may appear brighter or darker on the panel. This does
not affect product performance.
"" This product can be set to only one resolution for each screen size to obtain the optimum picture quality due to the nature of the panel. Using a
resolution other than the specified resolution may degrade the picture quality. To avoid this, it is recommended that you select the optimum resolution
specified for your product.
"" For detailed device specifications, visit the Samsung Electronics website.
65
Preset Timing Modes
Resolution
The screen will automatically be adjusted if a signal that belongs to the following standard
signal modes is transmitted from your PC. If the signals transmitted from the PC differ from the
standard mode, the screen may not be displayed. In such a case, change the settings as shown
in the following table by referring to the graphics card user manual.
Horizontal
Frequency
Vertical
Frequency
(kHz)
(Hz)
IBM, 720 x 400
31.469
MAC, 640 x 480
Pixel Clock
Sync Polarity
Port
(MHz)
(H/V)
HDMI IN
70.087
28.322
-/+
O
35.000
66.667
30.240
-/-
O
MAC, 832 x 624
49.726
74.551
57.284
-/-
O
MAC, 1152 x 870
68.681
75.062
100.000
-/-
O
VESA CVT, 3840 x 2160RB
110.500
49.977
442.000
+/-
-
VESA CVT, 3840 x 2160RB
133.313
59.997
533.250
+/-
-
VESA DMT, 640 x 480
31.469
59.940
25.175
-/-
O
VESA DMT, 640 x 480
37.861
72.809
31.500
-/-
O
VESA DMT, 640 x 480
37.500
75.000
31.500
-/-
O
VESA DMT, 800 x 600
37.879
60.317
40.000
+/+
O
VESA DMT, 800 x 600
48.077
72.188
50.000
+/+
O
VESA DMT, 800 x 600
46.875
75.000
49.500
+/+
O
VESA DMT, 1024 x 768
48.363
60.004
65.000
-/-
O
VESA DMT, 1024 x 768
56.476
70.069
75.000
-/-
O
VESA DMT, 1024 x 768
60.023
75.029
78.750
+/+
O
VESA DMT, 1152 x 864
67.500
75.000
108.000
+/+
O
VESA DMT, 1280 x 720
45.000
60.000
74.250
+/+
O
VESA DMT, 1280 x 800
49.702
59.810
83.500
-/+
O
VESA DMT, 1280 x 1024
63.981
60.020
108.000
+/+
O
VESA DMT, 1280 x 1024
79.976
75.025
135.000
+/+
O
VESA DMT, 1366 x 768
47.712
59.790
85.500
+/+
O
Resolution
Horizontal
Frequency
Vertical
Frequency
(kHz)
(Hz)
Pixel Clock
Sync Polarity
Port
(MHz)
(H/V)
HDMI IN
VESA DMT, 1440 x 900
55.935
59.887
106.500
-/+
O
VESA DMT, 1600 x 900RB
60.000
60.000
108.000
+/+
O
VESA DMT, 1680 x 1050
65.290
59.954
146.250
-/+
O
VESA DMT, 1920 x 1080
67.500
60.000
148.500
+/+
O
VESA DMT, 2560 x 1440RB
88.787
59.951
241.500
+/-
O
CTA-861, 720(1440) x 576i
15.625
50.000
27.000
-/-
O
CTA-861, 720(1440) x 480i
15.734
59.940
27.000
-/-
O
CTA-861, 720 x 576
31.250
50.000
27.000
-/-
O
CTA-861, 720 x 480
31.469
59.940
27.000
-/-
O
CTA-861, 1280 x 720
37.500
50.000
74.250
+/+
O
CTA-861, 1280 x 720
45.000
60.000
74.250
+/+
O
CTA-861, 1920 x 1080i
28.125
50.000
74.250
+/+
O
CTA-861, 1920 x 1080i
33.750
60.000
74.250
+/+
O
CTA-861, 1920 x 1080
27.000
24.000
74.250
+/+
O
CTA-861, 1920 x 1080
28.125
25.000
74.250
+/+
O
CTA-861, 1920 x 1080
33.750
30.000
74.250
+/+
O
CTA-861, 1920 x 1080
56.250
50.000
148.500
+/+
O
CTA-861, 1920 x 1080
67.500
60.000
148.500
+/+
O
CTA-861, 3840 x 2160
54.000
24.000
297.000
+/+
O
CTA-861, 3840 x 2160
56.250
25.000
297.000
+/+
O
CTA-861, 3840 x 2160
67.500
30.000
297.000
+/+
O
CTA-861, 3840 x 2160
112.500
50.000
594.000
+/+
O
CTA-861, 3840 x 2160
135.000
60.000
594.000
+/+
O
CTA-861, 4096 x 2160
54.000
24.000
297.000
+/+
O
CTA-861, 4096 x 2160
67.500
30.000
297.000
+/+
O
CTA-861, 4096 x 2160
112.500
50.000
594.000
+/+
O
CTA-861, 4096 x 2160
135.000
60.000
594.000
+/+
O
66
Chapter 09
Appendix
Responsibility for the Pay Service (Cost to
Customers)
"" When the service is requested, in spite of in warranty, we may charge you for a visit from a
service technician in the following cases.
Not a product defect
Cleaning of the product, Adjustment, Explanation, Re-installation and etc.
•• If a service technician is requested to give instructions on how to use product or simply
adjusts options without disassembling product.
•• If a defect is caused by external environmental factors (Internet, Antenna, Wired Signal,
etc.)
•• If a product is reinstalled or devices are connected additionally after installing the
purchased product for the first time.
•• If a product is reinstalled to move to a different spot or to move to a different house.
•• If the customer requests instructions on how to use another company's product.
•• If customer requests instructions on how to use the network or another company's
programme.
A Product damage caused by customer's fault
Product damage caused by customer's mishandling or wrong repair
If a product damage is caused by;
•• External impact or drop.
•• Use of supplies or separately sold product unspecified by Samsung.
•• Repair from a person besides an engineer of outsourcing service company or partner of
Samsung Electronics Co., Ltd.
•• Remodeling or repairing the product by customer.
•• Using it with incorrect voltage or non-authorized electrical connections.
•• Not following the "cautions" in User Manual.
Others
•• If product fails by natural disaster. (lightning, fire, earthquake, flood damage, etc)
•• If consumable components are all used up. (Battery, Toner, Fluorescent lights, Head,
Vibrator, Lamp, Filter, Ribbon, etc.)
"" If customer requests a service in case the product has no defect, service fee may be
charged. So please read User Manual first.
•• If customer requests software installation and setup for the product.
•• If a service technician removes/cleans dusts or foreign materials inside of the product.
•• If customer requests an installation additionally after purchasing a product through homeshopping or online.
67
Prevention of Afterimage Burn-in
What is afterimage burn-in?
Afterimage burn-in should not occur when the panel is operating normally. Normal operation
refers to a continuously changing video pattern. If the panel displays a fixed pattern for an
extended period of time a slight voltage difference may occur between the electrodes in pixels
that control the liquid crystals.
Such a voltage difference between electrodes increases with time and makes the liquid
crystals thinner. When this occurs, a previous image can remain on the screen when the pattern
changes.
This information is a guide to prevent afterimage burn-in. Viewing a fixed screen
for an extended period of time may cause afterimage burn-in. This problem is not
included in warranty.
Licence
The terms HDMI and HDMI High-Definition Multimedia Interface, and
the HDMI Logo are trademarks or registered trademarks of HDMI
Licensing LLC in the United States and other countries.
Open Source Licence Notice
In the case of using open source software, Open Source Licences are available on the
product menu. Open Source Licence Notice is written only English.
For information on the Open Source Licence Notice, contact the Samsung Customer Centre
or send email to oss.request@samsung.com.
Recommended prevention practices
Viewing a fixed screen for an extended period of time may cause afterimage burn-ins or
smudges. Turn off the product when it is not used for a long time, activate the Power Saving
mode, or run a moving screen saver.
68
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising