Whirlpool | PHN 961 TS/IX/A | Instruction for Use | Whirlpool PHN 961 TS/IX/A Instruction for Use

Whirlpool PHN 961 TS/IX/A Instruction for Use
EN
SAFETY INSTRUCTIONS
IMPORTANT TO BE READ AND OBSERVED
Download the complete instruction manual www.
aristonchannel.com or call the phone number
shown on the warranty booklet
Very young children (0-3 years) should be kept
away from the appliance. Young children (3-8 years)
should be kept away from the appliance unless
continuously supervised. Children from 8 years old
and above and persons with reduced physical,
sensory or mental capabilities or lack of experience
and knowledge can use this appliance only if they
are supervised or have been given instructions on
safe use and understand the hazards involved.
Children must not play with the appliance.
Cleaning and user maintenance must not be
carried out by children without supervision.
CAUTION : In case of hotplate glass breakage:shut immediately off all burners and any electrical
heating element and isolate the appliance from the
power supply; - do not touch the appliance surface;
-do not use the appliance.
The glass lid can break in if it is heated up. Turn off
all the burners and the electric plates before
closing the lid. Do not shout down lid when burner
alight.
Before using the appliance, read these safety
instructions. Keep them nearby for future
reference.
These instructions and the appliance itself provide
important safety warnings, to be observed at all
times. The manufacturer declines any liability for
failure to observe these safety instructions, for
inappropriate use of the appliance or incorrect
setting of controls.
These instructions are valid if the country
symbol appears on the appliance. If the symbol
doesn’t appear on the appliance, it is necessary to
refer to the technical instructions which will
provide the necessary instructions concerning
modification of the appliance to the conditions of
use of the country.
CAUTION : The use of the gas cooking appliance
results in the production of heat, moisture and
products of combustion in the room in which it is
installed. Ensure that the kitchen is well ventilated
especially when the appliance is in use: keep
natural ventilation holes open or install a
mechanical ventilation device (mechanical
extractor hood). Prolonged intensive use of the
appliance may call for additional ventilation, for
example opening of the window, or more effective
ventilation,increasing the level of mechanical
ventilation where present.
WARNING: The appliance and its accessible parts
become hot during use. Care should be taken to
avoid touching heating elements. Children less
than 8 years of age must be kept away unless
continuously supervised.
WARNING : If the hob surface is cracked, don’t
use the appliance – risk of electrical shock.
WARNING : Danger of fire : Do not store items on
the cooking surfaces.
CAUTION : The cooking process has to be
supervised. A short cooking process has to be
supervised continuously.
WARNING : Unattended cooking on a hob with
fat or oil can be dangerous – risk of fire. NEVER try
to extinguish a fire with water, but switch off the
appliance and then cover flame e.g. with a lid or a
fire blanket.
Do not use the hob as a work surface or support.
Keep clothes or other flammable materials away
from the appliance, until all the components have
cooled down completely – risk of fire.
If the information in this manual is not followed
exactly, a fire or explosion , may result causing
property damage or injury.
PERMITTED USE
CAUTION: the appliance is not intended to be
operated by means of an external switching device,
such as a timer, or separate remote controlled
system.
This appliance is intended to be used in
household and similar applications such as: staff
kitchen areas in shops, offices and other working
environments; farm houses; by clients in hotels,
motels, bed & breakfast and other residential
environments.
No other use is permitted (e.g. heating rooms).
This appliance is not for professional use. Do not
use the appliance outdoors.
Use pots and pans with bottoms the same width
as that of the burners or slightly larger (see specific
table). Make sure pots on the grates do not
protrude beyond the edge of the hob.
Improper use of the grids can result in damage
to the hob: do not position the grids upside down
or slide them across the hob.
Do not let the burner flame extend beyond the edge of the pan.
Do not use : Cast iron griddles, collar stones, terracotta pots and pans.
Heat diffusers such as metal mesh, or any other types. Two burners
simultaneously for one receptacle (e.g. Fish kettle).
Should particular local conditions of the delivered gas make the ignition
of burner difficult, it is advisable to repeat the operation with the knob
turned to small flame setting.
In case of installation of a hood above the cooktop, please refer to the
hood instructions for the correct distance.
The protective rubber feet on the grids represent a chocking hazard for
young children. After removing the grids, please ensure that all the feet
are correctly fitted.
INSTALLATION
The appliance must be handled and installed by
two or more persons - risk of injury. Use protective
gloves to unpack and install - risk of cuts.
Installation, including water supply (if any) and
electrical connections, and repairs must be carried
out by a qualified technician. Do not repair or
replace any part of the appliance unless specifically
stated in the user manual. Keep children away from
the installation site. After unpacking the appliance,
make sure that it has not been damaged during
transport. In the event of problems, contact the
dealer or your nearest After-sales Service. Once
installed, packaging waste (plastic, Styrofoam parts
etc.) must be stored out of reach of children - risk of
suffocation. The appliance must be disconnected
from the power supply before any installation
operation - risk of electrical shock. During
installation, make sure the appliance does not
damage the power cable - risk of fire or electrical
shock. Only activate the appliance when the
installation has been completed.
The electrical and gas connections must comply
with local regulation.
WARNING : Modification of the appliance and its
method of installation are essential in order to use
the appliance safely and correctly in all the
additional countries.
Use pressure regulators suitable for the gas
pressure indicated in the instruction.
The room must be equipped with an air
extraction system that expels any combustion
fumes.
The room must also allow proper air circulation,
as air is needed for combustion to occur normally.
The flow of air must not be less than 2 m3/h per kW
of installed power.
The air circulation system may take air directly
from the outside by means of a pipe with an inner
cross section of at least 100 cm2; the opening must
not be vulnerable to any type of blockages.
The system can also provide the air needed for
combustion indirectly, i.e. from adjacent rooms
fitted with air circulation tubes as described above.
However, these rooms must not be communal
rooms, bedrooms or rooms that may present a fire
hazard.
Liquid petroleum gas sinks to the floor as it is
heavier than air. Therefore, rooms containing LPG
cylinders must also be equipped with vents to
allow gas to escape in the event of a leak. As a
result LPG cylinders, whether partially or
completely full, must not be installed or stored in
rooms or storage areas that are below ground level
(cellars, etc.). It is advisable to keep only the cylinder
being used in the room, positioned so that it is not
subject to heat produced by external sources
(ovens, fireplaces, stoves, etc. ) which could raise
the temperature of the cylinder above 50°C.
Carry out all cabinet cutting works before fitting
the appliance in the furniture and remove all wood
chips and sawdust.
If the appliance is Not installed above an oven, a
separator panel (not included) must be installed in
the compartment under the appliance.
Should you experience difficulty in turning the burners knobs, please
contact After Sales Service for replacement of the burner tap if found to
be faulty.
The openings used for the ventilation and dispersion of heat must never
be covered.
GAS CONNECTION
WARNING : Prior to installation, ensure that the
local distribution conditions (nature of gas and gas
pressure) and the adjustment of the appliance are
compatible.
Check that the pressure of the gas supply is
consistent with the values indicated in Table 1
(“Burner and nozzle specifications”).
WARNING : The adjustment conditions for this
appliance are stated on the label (or data plate).
WARNING : This appliance is not connected to a
combustion products evacuation device. It shall be
installed and connected in accordance with current
installation regulations. Particular attention shall be
given to the relevant requirements regarding
ventilation.
If the appliances is connected to liquid gas, the
regulation screw must be fastened as tightly as
possible.
IMPORTANT : When gas cylinder is adopted, the
gas cylinder or gas container must be properly
settled (vertical orientation).
WARNING : This operation must be performed
by a qualified technician
Use only flexible or rigid metal hose for gas
connection.
Connection with a rigid pipe (copper or steel)
Connection to the gas system must be carried out
in such a way as not to place any strain of any kind
on the appliance. There is an adjustable L-shaped
pipe fitting on the appliance supply ramp and this
is fitted with a seal in order to prevent leaks. The
seal must always be replaced after rotating the
pipe fitting (the seal is provided with the
appliance). The gas supply pipe fitting is a threaded
1/2 gas cylindrical male attachment.
Connecting a flexible joint less stainless steel
pipe to a threaded attachment The gas supply pipe
fitting is a threaded 1/2 gas cylindrical male
attachment. These pipes must be installed so that
they are never longer than 2000 mm when fully
extended. Once connection has been carried out,
make sure that the flexible metal pipe does not
touch any moving parts and is not compressed.
Only use pipes and seals that comply with current
National regulations.
IMPORTANT : If a stainless steel hose is used, it
must be installed so as not touch any mobile part
of the furniture (e.g. drawer). It must pass through
an area where there are no obstructions and where
it is possible to inspect it on all its length.
The appliance should be connected to the main
gas supply or to gas cylinder in compliance with
the current National regulations. Before carry out
the connection, make sure that the appliance is
compatible with the gas supply you wish to use. If
this is not the case, follow the instructions indicated
in the paragraph “Adapting to different types of
gas”.
After connection to the gas supply, check for
leaks with soapy water. Light up the burners and
turn the knobs from max position 1* to minimum
position 2* to check flame stability.
ADAPTING TO DIFFERENT TYPES OF GAS
In order to adapt the appliance to a type of gas
other than the type for which it was manufactured
(indicated on the rating label), follow the dedicated
steps provided after installation drawings.
ELECTRICAL WARNINGS
IMPORTANT: The data relevant to the voltage an
power absorptions are indicated on the rating
plate.
The power cable must be long enough to
connect the appliance, once fitted in its housing, to
the main power supply. Do not pull the power
supply cable.
It must be possible to disconnect the appliance
from the power supply by unplugging it if plug is
accessible, or by a multi-pole switch installed
upstream of the socket in accordance with the
wiring rules and the appliance must be earthed in
conformity with national electrical safety standards.
Do not use extension leads, multiple sockets or
adapters. The electrical components must not be
accessible to the user after installation. Do not use
the appliance when you are wet or barefoot. Do
not operate this appliance if it has a damaged
power cable or plug, if it is not working properly, or
if it has been damaged or dropped.
If the supply cord is damaged, it must be
replaced with an identical one by the manufacturer,
its service agent or similarly qualified persons in
order to avoid a hazard - risk of electrical shock.
CLEANING AND MAINTENANCE
WARNING: Ensure that the appliance is switched
off and disconnected from the power supply
before performing any maintenance operation;
never use steam cleaning equipment - risk of
electric shock.
Do not use abrasive or corrosive products,
chlorine-based cleaners or pan scourers.
DISPOSAL OF PACKAGING MATERIALS
The packaging material is 100% recyclable and is marked with the
recycle symbol
.
The various parts of the packaging must therefore be disposed of
responsibly and in full compliance with local authority regulations
governing waste disposal.
DISPOSAL OF HOUSEHOLD APPLIANCES
This appliance is manufactured with recyclable or reusable materials.
Dispose of it in accordance with local waste disposal regulations.
For further information on the treatment, recovery and recycling of
household electrical appliances, contact your local authority, the
collection service for household waste or the store where you purchased
the appliance. This appliance is marked in compliance with European
Directive 2012/19/EU, Waste Electrical and Electronic Equipment (WEEE).
By ensuring this product is disposed of correctly, you will help prevent
negative consequences for the environment and human health.
The symbol on the product or on the accompanying documentation
indicates that it should not be treated as domestic waste but must be
taken to an appropriate collection center for the recycling of electrical
and electronic equipment.
ENERGY SAVING TIPS
Use pots and pans with bottom width equal to that of the cooking zone.
Only use flat-bottomed pots and pans.
When possible, keep pot lids on during cooking.
Use a pressure cooker to save even more energy and time.
Place the pot in the middle of the cooking zone marked on the hob.
DECLARATION OF CONFORMITY
This appliance meets the Ecodesign requirements set out in European
Regulation n. 66/2014, in conformity to the European standard EN 30-2-1.
INJECTORS TABLE
Type of gas
used
Type of burner
Injector
marking
Rated thermal
flow rate
Rated
consumption
CATEGORY II2H3+
Reduced heat
capacity
kW
Gas pressure
mbar
kW
min.
rat.
max.
NATURAL GAS
(Methane) G20
Reduced Rapid
Semi-rapid
Auxiliary
Triple Crown
Semi-Fish burner
110 (Y)
96 (Z)
71 (X)
133 (Z)
88
2,60
1,65
1,00
3,25
1,50
248 l/h
157 l/h
95 l/h
309 l/h
143 l/h
0,70
0,40
0,40
1,50
0,70
17
20
25
LIQUEFIED
PETROLEUM GAS
(Butane) G30
Reduced Rapid
Semi-rapid
Auxiliary
Triple Crown
Semi-Fish burner
80
64
50
91
60
2,60
1,65
1,00
3,25
1,50
189 g/h
120 g/h
73 g/h
236 g/h
109 g/h
0,70
0,40
0,40
1,50
0,70
20
28-30
35
LIQUEFIED
PETROLEUM GAS
(Propane) G31
Reduced Rapid
Semi-rapid
Auxiliary
Triple Crown
Semi-Fish burner
80
64
50
91
60
2,60
1,65
1,00
3,25
1,50
186 g/h
118 g/h
71 g/h
232 g/h
107 g/h
0,70
0,40
0,40
1,50
0,70
25
37
45
Type of gas used
Model configuration
6 BURNERS
Rated thermal
flowrate (kW)
Total rated
consumption
Air required (m3) for
burning 1m3 of gas
G20 20 mbar
1RR - 1SR - 1AUX - 1TC - 2SP
11,50
1095 l/h
9,52
G30 28-30 mbar
1RR - 1SR - 1AUX - 1TC - 2SP
11,50
836 g/h
30,94
G31 37 mbar
1RR - 1SR - 1AUX - 1TC - 2SP
11,50
821 g/h
23,80
ELECTRIC SUPPLY: 220-240 V ~ 50-60 Hz - 0,6W
EN
INSTALLATION
TECHNICAL INFORMATION FOR THE INSTALLER
• Use protective gloves for handling, preparing and installing the product.
• This product can be embedded in a worktop 20 ÷ 40 mm thick.
• If there is no oven beneath the hob, insert a separator panel that has a surface at least equal to the opening in the work surface. This panel must
be positioned at a maximum distance of 150 mm below the upper surface of the work surface but, in no case less than 20 mm from the bottom of
the hob. In the case that you intend to install an oven beneath the hob, make sure that it is equipped with a cooling system.
DIMENSIONS AND DISTANCES TO BE MAINTAINED
870 mm
510 mm
33 mmm
min. 600 mm
Min. 55 mm
835 mm
min. 650 mm
min. 420 mm
475 mm
NOTE: Kitchen cabinets adjacent to the appliance and taller than the top of the hob must be at least 200 mm from the edge of the hob.
Hoods must be installed according to their relative installation instruction manuals and at a minimum distance of 650 mm from the hob
(see figure). Place the wall cabinets adjacent to the hood at a minimum height of 420 mm from the hob (see figure). If the hob is installed
beneath a wall cabinet, the latter must be situated at a minimum of 700 mm above the hob.
ASSEMBLY
After having cleaned the perimeter surface, apply the supplied gasket to the hob as shown in the figure.
Position the hob in the worktop opening made respecting the dimensions indicated in the Instruction.
NOTE: the power supply cable must be long enough to permit its upward extraction.
To secure the hob, use the brackets (A) provided with it. Fit the brackets into the relevant bores shown by the arrow and fasten them by means of
their screws in accordance with the thickness of the worktop (see the following figures).
20 mm
A
20
40 mm
40
30 mm
30
GAS CONNECTION
• Connect elbow (A)* or (B)* supplied with to the hob inlet main pipe and interpose the washer (C) supplied, in
compliance with EN 549.
* Use elbow (A) for United Kingdom and elbow (B) for all other destinations.
• After connection to the gas supply, check for leaks with soapy water. Light up the burners and turn the knobs from
max position
A
C
to minimum position to check flame stability.
C
IMPORTANT: Before connection remove a transport plug from the connecting hole of the cooker gas pipeline
B
C
PRODUCT DESCRIPTION
1
5
3
1
4
1. Removable panstand grids
Symbols
2. Auxiliary burner
Shaded circle
Tap closed
3. Semi-rapid burner
Large flame
Maximum opening/delivery
and electric ignition
Minimum opening
or reduced delivery
4. Rediced rapid burner
5. Triple Crown burner
2
Small flame
6. Semi - Fish burner
7. Semi - Fish burner
1
8. Semi-rapid burner control knob
6
7
9. Reduced rapid burner control knob
10. Auxiliary burner control knob
1
11
8
12
13
10
9
11. Triple Crown burner control knob
12. Semi - Fish burner control knob
13. Semi - Fish burner control knob
DAILY USE
HOW TO USE THE HOB
Do not let the burner flame extend beyond the edge of the pan.
IMPORTANT: when the hob is in use, the entire hob area may
become hot.
• To ignite one of the burners, turn the relative knob anti-clockwise to
the maximum flame setting.
• Press the knob against the control panel to ignite the burner.
• After the burner has ignited, keep the knob pressed for about 5-10
seconds to allow proper device operation.
• This burner safety device shuts off the gas supply to the burner if
the flame goes out accidentally (because of sudden draught, an
interruption in the gas delivery, boiling over of liquids, etc.).
• The knob must not be pressed for more than 15 sec. If, after that
time has elapsed, the burner does not remain lit, wait at least
one minute before trying to light it again.
NOTE: should particular local conditions of the delivered gas
make the ignition of burner difficult, it is advisable to repeat the
operation with the knob turned to small flame setting.
The burner might go out when the knob is released. This means that
the safety device has not warmed up enough. In this case, repeat the
operations described above.
PRATICAL ADVICE FOR USING THE BURNERS
This hob has burners of different diameters. For better burner
performance, please stick to the following rules:
• use pots and pans with bottoms the same width as that of the burners
or slightly larger (see table on the right);
• only use flat-bottomed pots and pans;
• use the correct amount of water for cooking foods and keep the pot
covered;
• make sure pots on the grates do not protrude beyond the edge of
the hob;
• In the case of pans with convex bottoms (WOK), use the support grille
(not provided), which should be positioned only on the multi-ring
burner.
• Avoid accidentally knocking the hob with pans,racks or other kitchen
utensil.
• Do not leave empty steak grills over the lit burner for longer than 5
minutes
IMPORTANT: improper use of the grids can result in damage to the
hob: do not position the grids upside down or slide them across
the hob.
BURNER
POT Ø
Triple crown
From 24 to 26 cm
Semi-fish
From 16 to 20 cm
Rapid Reduced
From 24 to 26 cm
Semi-rapid
From 16 to 20 cm
Auxiliary
From 10 to 14 cm
Do not use:
• cast iron griddles, ollar stones, terracotta pots and pans;
• heat diffusers such as metal mesh, or any other types;
• two burners simultaneously for one receptacle (e.g. fish kettle).
Liquids spilled on hot hob area can cause glass damage.
ADAPTING TO DIFFERENT TYPES OF GAS
This operation must be performed by a qualified technician.
If the appliance is intended to operate with a different gas from the gas
type stated on the rating plate and information label on the top of the
hob, change the injectors.
Remove the information label and keep it with the instructions booklet.
Use pressure regulators suitable for the gas pressure indicated in
the Instruction:
• the gas injector must be changed by After Sales Service or a qualified
technician;
• injector not supplied with the appliance must be ordered from After
Sales Service;
• adjust the minimum setting of the taps.
NOTE: when liquid petroleum gas is used (G30/G31), the minimum
gas setting screw must be tightened as far as it will go.
IMPORTANT: should you experience difficulty in turning the
burners knobs, please contact the After Sales Service for the
replacement of the burner tap if found to be faulty.
IMPORTANT: when gas cylinder is adopted, the gas cylinder or gas
container must be properly settled (vertical orientation).
REPLACING THE INJECTORS (see the injector table in the Safety
instructions)
• Remove grids (A).
• Extract burners (B).
• Using a socket spanner of the appropriate size unscrew the injector
(C), unscrew the injector to be replaced.
• Replace it with the injector suitable for the new type of gas.
• Re-assemble the injector in (D).
• If you have a multiple crown burner use side spanner to replace the
injector (E).
Before installing the hob, remember to affix the gas calibration plate
supplied with the injectors in such a way that it covers the existing
information relating to gas calibration.
EN
ADJUSTING MINIMUM GAS SETTING OF TAPS
To ensure that the minimum setting is correctly adjusted, remove the
knob and proceed as follows:
• tighten screw to reduce the flame height (-);
• loosen screw to increase the flame height (+).
The adjustment must be performed with the tap in minimum gas setting
position (small flame):
• The primary air of the burners does not need to be adjusted;
• At this stage, light up the burners and turn the knobs from max
position to minimum position to check flame stability.
Upon completion of adjustment, reseal using sealing wax or an
equivalent material.
MAINTENANCE AND CLEANING
Disconnect the appliance from the power supply.
CLEANING THE HOB SURFACE
• All the enamelled and glass parts should be cleaned with warm water
and neutral solution.
• Stainless steel surfaces may be stained by calcareous water or
aggressive detergents if left in contact for too long. Any food spills
(water, sauce, coffee, etc.) should be wiped away before they dry.
• Clean with warm water and neutral detergent, and then dry with a
soft cloth or chamois. Remove baked-on dirt with specific cleaners for
stainless steel surfaces.
NOTE: clean stainless steel only with soft cloth or sponge.
• Do not use abrasive or corrosive products, chlorine-based cleaners or
pan scourers.
• Do not use steam cleaning appliances.
• Do not use flammable products.
• Do not leave acid or alkaline substances, such as vinegar, mustard,
salt, sugar or lemon juice on the hob.
CLEANING THE HOB PARTS
• Clean glass and enamelled parts only with soft cloth or sponge.
• Grids, burner caps and burners can be removed to be cleaned.
• Clean them by hand with warm water and non-abrasive detergent,
removing any food residues and checking that none of the burner
openings is clogged.
• Rinse and dry.
• Refit burners and burner caps correctly in the respective housings.
• When replacing the grids, make sure that the panstand area is aligned
with the burner.
• Models equipped with electrical ignition plugs and safety device
require thorough cleaning of the plug end in order to ensure correct
operation. Check these items frequently, and if necessary, clean them
with a damp cloth. Any baked-on food should be removed with a
toothpick or needle.
NOTE: to avoid damaging the electric ignition device, do not use
it when the burners are not in their housing.
TROUBLESHOOTING
If the hob will not operate correctly, before calling the After-Sales
Service, refer to the Troubleshooting Guide to determine the problem.
1. The burner fails to ignite or the flame is not even
Check that:
• the gas or electrical supplies are not shut off and especially that
the gas supply tap is open;
• the gas cylinder (liquid gas) is not empty;
• the burner openings are not clogged;
• the plug end is not dirty;
• all the burner parts have been positioned correctly;
• there are no draughts near the hob.
2. The burner does not stay lit
Check that:
• when lighting the burner, the knob has been pressed for enough
time to activate the protection device;
• the burner openings are not clogged near the thermocouple;
• the end of the safety device is not dirty;
• the minimum gas setting is correct (see relevant paragraph).
3. The containers are not stable
Check that:
• the bottom of the container is perfectly flat;
• the container is centred on the burner;
• the grids have not been exchanged or positioned incorrectly.
If after the above checks the fault still occurs, get in touch with the
nearest After Sales Service.
AFTER-SALES SERVICE
In order to receive a more complete assistance, please register your
product on www‌.‌aristonchannel‌.‌com
• the service number (number after the word Service on the rating
plate). The service number is also indicated on the guarantee booklet;
BEFORE CALLING THE AFTER-SALES SERVICE:
1. See if you can solve the problem by yourself with the help of the
suggestions given in the TROUBLESHOOTING.
2. Switch the appliance off and back on again to see if the fault persists.
IF AFTER THE ABOVE CHECKS THE FAULT STILL OCCURS, GET IN
TOUCH WITH THE NEAREST AFTER-SALES SERVICE.
To receive assistance, call the number shown on the warranty booklet
or follow the instructions on the website www‌.‌aristonchannel‌.‌com.
• your full address;
• your telephone number.
If any repairs are required, please contact an authorized after-sales
service (to guarantee that original spare parts will be used and repairs
carried out correctly).
When contacting our Client After sales service, always specify:
• a brief description of the fault;
• the type and exact model of the appliance;
Type: XXX
Mod.: XXX
XXXXXXXXXXXXXXXXXXXX
Made in X
XXXXXXXXXXXXXXX
XXXXXXXXXXXXXXXXXXXXXX
01
XXXX XXX XXXXX
XX XXXX XXXXX
XXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXX
400011377855
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising