Indesit | DFP 27B+96 Z | Setup and user guide | Indesit DFP 27B+96 Z Setup and user guide

Indesit DFP 27B+96 Z Setup and user guide
EN
DAILY REFERENCE
GUIDE
THANK YOU FOR BUYING A INDESIT PRODUCT.
In order to receive a more complete assistance, please
register your appliance on:
www.indesit.com
You can download the Safety Instructions and the
Use and Care Guide, by visiting our website
docs.indesit.eu and following the Instructions on
the back of this booklet.
Before using the appliance carefully read Health and Safety guide.
PRODUCT DESCRIPTION
APPLIANCE
1
7
2
8
3
9
4
5
6
11
10
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
Upper rack
Foldable flaps
Upper rack height adjuster
Upper spray arm
Lower rack
Cutlery basket
Lower spray arm
Filter Assembly
Salt reservoir
Detergent and Rinse Aid dispensers
Rating plate
Control panel
Service:
0000 000 00000
12
CONTROL PANEL
3
1
1.
2.
3.
4.
5.
On-Off/Reset button
Program selection knob
Half load/Extra Light button with indicator light
Delay button with indicator light
Start/Pause button with indicator light
6.
7.
8.
9.
10.
2
4
6 7 8
5
9 10
Washing and Delayed Start 3h. indicator light
Drying and Delayed Start 6h. indicator light
Wash Cycle End and Delayed Start 9h. Indicator light
Rinse Aid refill indicator light
Salt refill indicator light
1
FIRST TIME USE
SALT, RINSE AID AND DETERGENT
ADVICE REGARDING THE FIRST TIME USE
After installation, remove the stoppers from the racks and the retaining elastic elements from the upper rack.
FILLING THE SALT RESERVOIR
The use of salt prevents the formation of LIMESCALE on the dishes and
on the machine’s functional components.
• It is important that the salt reservoir be never empty.
• It is important to set the water hardness.
The salt reservoir is located in the lower part of the dishwasher (see Product Description) and should be filled when the SALT REFILL indicator
light
in the control panel is lit .
1. Remove the lower rack and unscrew the
reservoir cap (anticlockwise).
2. Only the first time you do this: fill the salt reservoir with water.
3. Position the funnel (see figure) and fill the salt
reservoir right up to its edge (approximately
1 kg); it is not unusual for a little water to leak
out.
4. Remove the funnel and wipe any salt residue
away from the opening.
Make sure the cap is screwed on tightly, so that no detergent can get
into the container during the wash program (this could damage the
water softener beyond repair).
Whenever you need to add salt, it is mandatory to complete the
procedure before the beginning of the washing cycle.
SETTING THE WATER HARDNESS
To allow the water softener to work in a perfect way, it is essential that
the water hardness setting is based on the actual water hardness in
your house. This information can be obtained from your local water
supplier.
The factory setting is for avarage (3) water hardness.
• Switch on the appliance by pressing the ON/OFF button.
• Switch off the appliance by pressing the ON/OFF button.
• Hold down button START/PAUSE for 5 seconds, until you hear a beep.
• Switch on the appliance by pressing the ON/OFF button.
• The salt indicator light flashes (as many times as the current selection).
• Set the PROGRAM SELECTION knob to the desired hardness level
number (see WATER HARDNESS TABLE).
°dH
°fH
German degrees
French degrees
0-6
0 - 10
1
Soft
2
Medium
7 - 11
11 - 20
3
Average
12 - 17
21 - 30
4
Hard
18 - 34
31 - 60
5
Very hard
35 - 50
61 - 90
• Switch off the appliance by pressing the ON/OFF button.
Setting is complete!
As soon as this procedure is complete, run a program without loading.
Only use salt that has been specifically designed for dishwashers.
After the salt has been poured into the machine, the SALT REFILL indicator light switches off.
If the salt container is not filled, the water softener and the
heating element may be damaged as a result.
2
Rinse aid makes dish DRYING easier. The rinse aid dispenser A should
be filled when the RINSE AID REFILL
indicator light in the control
panel is lit.
35
25
MA X
B
A
1. Open the dispenser B by pressing and pulling up the tab on the lid.
2. Pour in the rinse aid (max.110 ml), making sure it does not overflow
from the dispenser. If this happens, clean the spill immediately with a
dry cloth.
3. Press the lid down until you hear a click to close it.
NEVER pour the rinse aid directly into the appliance tub.
ADJUSTING THE DOSAGE OF RINSE AID
If you are not completely satisfied with the drying results, you can adjust the quantity of rinse aid used.
• Switch the dishwasher on using the ON/OFF button.
• Switch it off using the ON/OFF button.
• Press button START/PAUSE three times - a beep will be heard.
• Switch it on using the ON/OFF button.
• The rinse-aid indicator light will flash (as many times as the current selection).
• Set the PROGRAM SELECTION knob to the level number of rinse aid
quantity to be supplied.
• Switch it off using the ON/OFF button
Setting is complete!
If the rinse aid level is set to ZERO (ECO), no rinse aid will be supplied. The
LOW RINSE AID indicator light will not be lit if you run out of rinse aid.
A maximum of 5 levels can be set according to the dishwasher model. The
factory setting is specific to the model, please follow instruction above
to check this for your machine.
• If you see bluish streaks on the dishes, set a low number (1-2).
• If there are drops of water or limescale marks on the dishes, set a
mid-range number (3-4).
FILLING THE DETERGENT DISPENSER
Water Hardness Table
Level
FILLING THE RINSE AID DISPENSER
To open the detergent dispenser
use the opening device A. Introduce
the detergent into the dry dispenser
B only. Place the amount of
detergent for pre-washing directly
B
inside the tub.
A
1. When measuring out the detergent refer to the mentioned earlier information
to add the proper quantity. Inside the
dispenser B there are indications to help
the detergent dosing.
2. Remove detergent residues from the edges of the dispenser and
close the cover until it clicks.
3. Close the lid of the detergent dispenser by pulling it up until the
closing device is secured in place.
The detergent dispenser automatically opens up at the right time
according to the program.
EN
Program
CoolDry
Drying
PROGRAMS TABLE
Available
options *)
Detergent
container
Duration
of wash
program
(h:min)**)
Water
consumption
(litres/cycle)
Energy
consumption
(kWh/cycle)
3:10
9,5
0,93
-
2:00 - 3:10
14,0 - 17,0
1,50 - 1,85
-
1:30 - 2:30
14,5 - 16,0
1,15 - 1,30
0:40
9,0
0,90
0:12
4,5
0,01
1:40
10,0
1,30
1:00
11,0
1,20
Tub
1. Eco
50°
2. Auto Intensive
65°
3. Auto Normal
55°
4. Rapid 40’
50°
-
-
-
-
-
-
-
-
-
5. Soak
6. Baby Care
65°
7. Extra
65°
-
-
-
B
-
-
ECO program data is measured under laboratory conditions according to European Standard EN 50242. Note for Test Laboratories: For information on
comparative EN testing conditions, please send an email to the following address: assistenza_en_lvs@indesitcompany.com
Pre-treatment of the dishes is not needed before any of the programs.
*) Not all options can be used simultaneously.
**) The duration of the program shown on the display or in the booklet is an estimate calculated on standard conditions. The actual time may vary
depending on many factors such as temperature and pressure of the incoming water, room temperature, amount of detergent, quantity and type of load,
load balancing, additional selected options and sensor calibration. The sensor calibration can increase program duration up to 20 min.
Standby consumption: Left-on mode consumption: 6 W - Off mode consumption: 0.5 W
PROGRAMS DESCRIPTION
Instructions on wash cycle selection.
ECO
Normally soiled crockery. Standard program, the most efficient in
terms of its combined energy and water consumption.
AUTO INTENSIVE
Automatic program for heavily soiled dishes and pans (not to be used
for delicate items).
AUTO NORMAL
Automatic program for normally soiled pans and dishes.
RAPID 40’
Program to be used for lightly-soiled dishes with no dried food
residues.
BABY CARE
Program combined with the Baby Care specially-designed basket ensures the best cleaning results and sanitization of baby accessories
(soother, pacifiers, teats) while washing also normally or heavily soiled
crockery.
EXTRA
Program that allows to wash very big items loaded in the lower rack.
Notes:
Please note that cycles like Fast or Rapid are most effective for lightly
soiled dishes.
To reduce consumption even further, only run the dishwasher
when it is full.
SOAK
Use to refresh crockery planned to be washed later. No detergent to be
used with this program.
3
OPTIONS AND FUNCTIONS
OPTIONS can be selected directly by pressing the corresponding button (see CONTROL PANEL).
If an option is not compatible with the selected program see
PROGRAMS TABLE, the corresponding LED flashes rapidly 3
times and beeps will sound. The option will not be enabled.
EXTRA
EXTRA makes it possible to carry out a heavy-duty
wash cycle of large crockery up to a max height of 53
cm: baking pans, oven grids, dripping pans, hob grids,
large saucepans, serving dishes, pizza dishes, stainlesssteel hood filters.
Remove the upper rack to load bulky crockery.
Release the two locks (right
and left) and pull out the
rack.
HALF LOAD / EXTRA LIGHT
The button has two functions: HALF LOAD and EXTRA
LIGHT.
Select the wash cycle and press the HALF LOAD/EXTRA
LIGHT button; the indicator light will go on.
Press the HALF LOAD/EXTRA LIGHT button again to
deselect this option.
When the upper rack is
fitted, the locks must be
always closed.
HALF LOAD
If there are not many dishes to be washed, a half load
cycle may be used in order to save water, electricity and
detergent.
The amount of detergent can be halved.
EXTRA LIGHT
Compatible with the wash cycle EXTRA only.
This option makes EXTRA suitable to large delicate
crockery and items. This option includes no drying phase.
Make sure the crockery and items are dishwashersafe.
DELAY
It is possible to delay the start time of the wash cycle by
3, 6 or 9 hours:
1. After selecting the desired wash cycle and any other
options, press the DELAYED START button, the indicator
light will go on.
2. Select the desired delay time by pressing the DELAYED
START button repeatedly. The wash phase (3 hours),
drying phase (6 hours) and end (9 hours) indicator lights
will go on in succession.
If the DELAYED START button is pressed again, the option
is deselected and the indicator light goes off.
3. After the selection process, the countdown will begin
if the Start/Pause button is pressed. The selected delayperiod indicator light flashes and the Start/Pause button
stops flashing (fixed light).
4. Once this time has elapsed, the DELAYED START
indicator light goes off and the wash cycle begins.
The Delay function cannot be set once a wash cycle
has been started.
4
In order for the water to reach the crockery everywhere, arrange
it as shown in the Figure.
The cycle can also be used on large delicate crockery using the
option EXTRA LIGHT (see OPTIONS AND FUNCTIONS).
Do not start the dishwasher without the upper rack using
wash cycles other than EXTRA.
To carry out the wash cycle Extra and Extra with the EXTRA
LIGHT option pour the detergent DIRECTLY INTO THE TUB
and not into the dispenser.
CoolDry
CoolDry is a convection drying system which automatically opens the
door during/after drying phase to ensure exceptional drying performance every day. Door opens at the temperature that is safe to your
kitchen furniture, thus door will not be opened when the option of
SANI RINSE or TURBO are on.
As additional steam protection, special designed protection foil is added together with the dishwasher (depending on the model type - can
be the need to buy it). To see how to mount protection foil please refer
to (INSTALLATION GUIDE).
CoolDry functionality could be disabled by the user as follows:
• To DISABLE: Switch On, then switch Off the machine.
Keep the DELAY button pressed for 5 sec., at the end of 5 sec the
dishwasher plays a short beep. Press the On/Off button, the dishwasher plays the long beep. Switch On the machine.
• To ENABLE: Switch On, then switch Off the machine.
Keep the DELAY button pressed for 5 sec., at the end of 5 sec
the dishwasher plays a short beep. Press the On/Off button, the
dishwasher plays the melody. Switch On the machine.
EN
DAILY USE
1. CHECK WATER CONNECTION
Check that the dishwasher is connected to the water
supply and that the tap is open.
MODIFYING A RUNNING PROGRAM
3. LOAD THE RACKS (see LOADING THE RACKS).
If a wrong program was selected, it is possible to change it,
provided that it has only just begun: press and hold the ON/OFF
button, the machine will switch off.
Switch the machine back on using the ON/OFF button and select the new wash cycle and any desired options; start the cycle
by pressing the START/PAUSE button.
4. FILLING THE DETERGENT DISPENSER
(see PROGRAMS TABLE).
ADDING EXTRA CROCKERY
5. CHOOSE THE PROGRAM AND CUSTOMISE THE CYCLE
Select the most appropriate program in accordance with
the type of crockery and its soiling level (see PROGRAMS
DESCRIPTION) by turning the PROGRAM SELECTION knob
clockwise. Select the desired options (see OPTIONS AND FUNC-
ACCIDENTAL INTERRUPTIONS
2. SWITCH ON THE DISHWASHER
Press the ON/OFF button.
TIONS).
6. START
Start the wash cycle by pressing the START/PAUSE button.
When the program starts you hear a beep.
7. END OF WASH CYCLE
At the end of the wash cycle the END indicator light will
switch on. Switch off the appliance by pressing the ON/OFF
button and open the door.
Wait for a few minutes before removing the crockery - to
avoid burns.
Unload the racks, beginning with the lower one.
Press the START/PAUSE button and open the door, taking care
to avoid the escaping steam, and place the crockery inside
the dishwasher. Press the START/PAUSE button: The cycle will
start again after a long beep has been emitted.
If the door is opened during the wash cycle or there is a power
cut, the cycle stops. It starts again from the point at which it
was interrupted once the door has been shut or the electricity
supply restored.
For more information about the functions, you can request or download from the WEB a Use & Care Guide by following the instructions on the last page.
The machine will switch off automatically during certain
extended periods of inactivity, in order to minimise electricity
consumption. If the crockery is only lightly soiled or if it has
been rinsed with water before being placed in the dishwasher,
reduce the amount of detergent used accordingly.
ADVICE AND TIPS
TIPS
Before loading the baskets, remove all food residues from the crockery and empty the glasses. You do not need to rinse beforehand
under running water.
Arrange the crockery so that it is held in place firmly and does
not tip over; and arrange the containers with the openings facing
downwards and the concave/convex parts placed obliquely, thus
allowing the water to reach every surface and flow freely.
Warning: lids, handles, trays and frying pans do not prevent the
sprayer arms from rotating. Place any small items in the cutlery
basket. Very soiled dishes and pans should be placed in the lower
basket because in this sector the water sprays are stronger and
allow a higher washing performance.
After loading the appliance, make sure that the sprayer arms can
rotate freely.
HYGIENE
To avoid odour and sediment which can be accumulated in the
dishwasher please run a high temperature program at least one
a month. Use a tea spoon of detergent and run it without the
loading to clean your appliance.
UNSUITABLE CROCKERY
• Wooden crockery and cutlery.
• Delicate decorated glasses, artistic handicraft and antique
crockery. Their decorations are not resistant.
• Parts in synthetic material which do not withstand high
temperatures.
• Copper and tin crockery.
• Crockery soiled with ash, wax, lubricating grease or ink.
The colours of glass decorations and aluminium/silver pieces
can change and fade during the washing process. Some types of
glass (e.g. crystal objects) can become opaque after a number of
wash cycles too.
DAMAGE TO GLASS AND CROCKERY
• Only use glasses and porcelain guaranteed by the manufacturer as dishwasher safe.
• Use a delicate detergent suitable for crockery.
• Collect glasses and cutlery from the dishwasher as soon as
the wash cycle is over.
5
LOADING THE RACKS
UPPER RACK
LOWER RACK
Load delicate and light dishes: glasses, cups, saucers, low salad bowls.
For pots, lids, plates, salad bowls, cutlery etc. Large plates and lids
should ideally be placed at the sides to avoid interferences with the
spray arm. The lower rack has tip-up supports which can be used in
a vertical position when arranging plates or in a horizontal position
(lower) to load pans and salad bowls easily.
n
n
(loading example for the upper rack)
(loading example for the lower rack)
ADJUSTING THE HEIGHT OF THE UPPER RACK
The height of the upper rack can be adjusted: high position to place
bulky crockery in the lower basket and low position to make the most
of the tip-up supports by creating more space
upwards and avoid collision with the items
loaded into lower rack. The upper rack is equipped with a Upper Rack height adjuster (see
figure), without pressing the levers, lift it up by
simply holding the rack sides, as soon as the
rack is stable in its upper position.
To restore to the lower position, press the levers
A at the sides of the rack and move the basket
downwards.
We strongly recommend that you do not
adjust the height of the rack when it is loaded.
NEVER raise or lower the basket on one side only.
FOLDABLE FLAPS WITH ADJUSTABLE POSITION
CUTLERY BASKET
It is fitted with top grids for improved cutlery arrangement. The cutlery
basket should be positioned only at the front of the lower rack.
A
The side foldable flaps can be positioned at three different heights to
optimize the arrangement of crockery inside
the rack. Wine glasses can be placed safely
in the foldable flaps by inserting the stem of
each glass into the corresponding slots. For
optimum drying results incline the foldable
flaps more. To change the inclination, pull up
the foldable flap, slide it slightly and position
it as you wish.
6
Knives and other utensils with sharp edges must be placed in the
cutlery basket with the points facing downwards or they must be
positioned horizontally in the tip-up compartments on the upper
rack.
EN
CARE AND MAINTENANCE
CLEANING THE FILTER ASSEMBLY
CLEANING THE SPRAY ARMS
Regularly clean the filter assembly so that the filters do not clog and
that the waste water flows away correctly. The filter assembly consists
of three filters which remove food residues from the washing water
and then recirculate the water: to obtain the best washing results, you
need to keep them clean.
The dishwasher must not be used without filters or if the filter is
loose.
After several washes, check the filter assembly and if necessary clean it
thoroughly under running water, using a non-metallic brush and following the instructions below:
1. Turn the cylindrical filter A in an anti-clockwise direction and pull it out
(Fig 1).
2. Remove the cup filter B by exerting a slight pressure on the side
flaps (Fig 2).
3. Slide out the stainless-steel plate filter C (Fig 3).
4. Inspect the trap and remove any food residues. NEVER REMOVE
the wash-cycle pump protection (black detail) (Fig 4).
On occasions, food residue may become encrusted onto the spray
arms and block the holes used to spray the water. It is therefore recommended that you check the arms from time to time and clean them
with a small non-metallic brush.
1
To remove the upper spray arm, turn the plastic locking ring in an anticlockwise direction. The upper spray arm should be replaced so that
the side with the greater number of holes is facing upwards.
2
B
A
A
The lower spray arm may be removed by pulling it upwards.
CLEANING THE WATER INLET HOSE
If the water hoses are new or have not been used for an extended
period of time, let the water run to make sure it is clear and free of
impurities before performing the necessary connections. If this
precaution is not taken, the water inlet could become blocked and
damage the dishwasher.
C
3
4
After cleaning the filters, re-place the filter assembly and fix it in position correctly; this is essential for maintaining the efficient operation
of the dishwasher.
7
TROUBLESHOOTING
Your dishwasher may not work properly.
Before contacting the Service Centre check if the problem can be solved by going through the following list.
PROBLEMS
POSSIBLE CAUSES
SOLUTIONS
The dishwasher
won’t start
or does not
respond to
commands.
The appliance has not been plugged
in properly.
Power outage.
Insert the plug into the socket.
The dishwasher door is not closed.
Vigorously push the door until you hear the “click”.
Switch off the appliance by pressing the ON/OFF button, switch it back
on after approximately one minute and reset the program.
Wait until the wash cycle finishes.
It does not respond to commands.
The dishwasher The wash cycle has not finished yet.
won’t drain.
The drain hose is bent.
The sink drain pipe is blocked.
The filter is clogged up with food
residues.
The dishwasher The dishes are rattling against each
makes
excessive
An excessive amount of foam has
noise.
been produced.
The dishes are
not clean.
The crockery has not been arranged
properly.
The spray arms cannot rotate freely,
being hindered by the dishes.
The wash cycle is too gentle.
An excessive amount of foam has
been produced.
The cap on the rinse aid compartment
has not been shut correctly.
The filter is soiled or clogged.
There is no salt.
The dishwasher starts automatically when the power returns.
Check that the drain hose is not bent (see INSTALATION INSTRUCTION).
Clean the sink drain pipe.
Clean the filter (see CLEANING THE FILTER ASSEMBLY).
Position the crockery correctly (see LOADING THE RACKS).
The detergent has not been measured out correctly or it is not suitable for use in dishwashers (see FILLING THE DETERGENT DISPENSER). Reset
the current cycle by switching OFF the dishwasher, then switch it on
again, select a new program and close the door. Press the START/PAUSE
button. Please do not add any detergent.
Arrange the crockery correctly (see LOADING THE RACKS).
Arrange the crockery correctly (see LOADING THE RACKS).
Select an appropriate wash cycle (see PROGRAMS TABLE).
The detergent has not been measured out correctly or it is not suitable
for use in dishwashers (see FILLING THE DETERGENT DISPENSER).
Make sure the cap of the rinse aid dispenser is closed.
Clean the filter assembly (see CARE AND MAINTENANCE).
Fill the salt reservoir (see FILLING THE SALT RESERVOIR).
MAINTENANCE AND TROUBLESHOOTING GUIDE
For more information, maintenance procedures and troubleshooting, see the Use and Care Guide
The Use and Care Guide can be obtained by:
• After-Sales Service; phone number see in warranty
booklet.
• download from website: docs.indesit.eu
• use QR code
CONTACTING AFTER-SALES SERVICE
When you contact the After-Sales Service, you must provide the codes shown on the rating plate attached to the
left or right side inside the door of the dishwasher.
The phone number is listed
in the warranty booklet or on the
website:
www.indesit.com
IEC 436
:
TECHNICAL DATASHEET
The technical data containing the energy consumption
data can be downloaded from the website:
docs.indesit.eu
400011356370
03/2019 jk - Xerox Fabriano
8
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising