Indesit | DFG 15B10 ES | Setup and user guide | Indesit DFG 15B10 ES Setup and user guide

Indesit DFG 15B10 ES Setup and user guide
EN
DAILY REFERENCE
GUIDE
THANK YOU FOR BUYING A INDESIT PRODUCT.
In order to receive a more complete assistance, please
register your appliance on: www.indesit.eu/register
You can download the Safety Instructions and the
Use and Care Guide, by visiting our website
docs.indesit.eu and following the Instructions on the
back of this booklet.
Before using the appliance carefully read Health and Safety guide.
PRODUCT DESCRIPTION
APPLIANCE
1
7
2
8
3
9
4
5
6
11
10
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
Upper rack
Foldable flaps
Upper rack height adjuster
Upper spray arm
Lower rack
Cutlery basket
Lower spray arm
Filter Assembly
Salt reservoir
Detergent and Rinse Aid dispensers
Rating plate
Control panel
Service:
0000 000 00000
12
CONTROL PANEL
1
1.
2.
3.
4.
On-Off/Reset button
Program selection knob
Indicator light Washing
Indicator light Drying
5.
6.
7.
2
3
4
5
6
7
Indicator light Wash Cycle Complete
Start/Pause button and indicator lights
Salt refill indicator light
1
FIRST TIME USE
SALT, RINSE AID AND DETERGENT
ADVICE REGARDING THE FIRST TIME USE
FILLING THE RINSE AID DISPENSER
After installation, remove the stoppers from the racks and the retaining elastic elements from the upper rack.
Rinse aid makes dish DRYING easier. The rinse aid dispenser A should
be filled when when the dark optical indicator on the dispenser door C
becomes transparent.
C
FILLING THE SALT RESERVOIR
The use of salt prevents the formation of LIMESCALE on the dishes and
on the machine’s functional components.
• It is important that the salt reservoir be never empty.
• It is important to set the water hardness.
35
25
MA X
TThe salt reservoir is located in the lower part of the dishwasher (see
PRODUCT DESCRIPTION) and should be filled when the SALT REFILL indicator light
in the control panel is lit.
B
A
1. Remove the lower rack and unscrew the
reservoir cap (anticlockwise).
2. Only the first time you do this: fill the salt reservoir with water.
3. Position the funnel (see figure) and fill the salt
reservoir right up to its edge (approximately
1 kg); it is not unusual for a little water to leak out.
4. Remove the funnel and wipe any salt residue
away from the opening.
Make sure the cap is screwed on tightly, so that no detergent can get
into the container during the wash program (this could damage the
water softener beyond repair).
Whenever you need to add salt, it is mandatory to complete the
procedure before the beginning of the washing cycle.
1. Open the dispenser B by pressing and pulling up the tab on the lid.
2. Pour in the rinse aid (max.110 ml), making sure it does not overflow
from the dispenser. If this happens, clean the spill immediately with
a dry cloth.
3. Press the lid down until you hear a click to close it.
NEVER pour the rinse aid directly into the appliance tub.
SETTING THE WATER HARDNESS
• Everything is off.
To allow the water softener to work in a perfect way, it is essential that
the water hardness setting is based on the actual water hardness in
your house. This information can be obtained from your local water
supplier.
The factory setting is for average (3) water hardness.
• Set the level of rinse aid quantity to be supplied using the
PROGRAM SELECTION knob (see PROGRAMS TABLE).
• Switch on the appliance by pressing the ON/OFF button.
• Switch off the appliance by pressing the ON/OFF button.
• Hold down button START/PAUSE for 5 seconds, until you hear a beep.
• Switch on the appliance by pressing the ON/OFF button.
• The salt indicator light flashes (as many times as the current selection.)
• Set the PROGRAM SELECTION knob to the desired hardness level
number (see WATER HARDNESS TABLE).
Water Hardness Table
Level
ADJUSTING THE DOSAGE OF RINSE AID
If you are not completely satisfied with the drying results, you can adjust the quantity of rinse aid used.
• Switch the dishwasher on using the ON/OFF button.
• Switch it off using the ON/OFF button.
• Press button START/PAUSE three times - a beep will be heard.
• Switch it on using the ON/OFF button.
• Switch it off using the ON/OFF button.
Setting is complete!
If the rinse aid level is set to 1 (ECO), no rinse aid will be supplied. The
LOW RINSE AID indicator light will not be lit if you run out of rinse aid.
A maximum of 5 levels can be set according to the dishwasher model.
The factory setting is specific to the model, please follow instruction
above to check this for your machine.
• If you see bluish streaks on the dishes, set a low number (2-3).
• If there are drops of water or limescale marks on the dishes, set a
mid-range number (4-5).
FILLING THE DETERGENT DISPENSER
°dH
°fH
German degrees
French degrees
To open the detergent dispenser use the opening device A.
Introduce the detergent into the dry dispenser B only. Place the
amount of detergent for pre-washing directly inside the tub.
1
Soft
0-6
0 - 10
2
Medium
7 - 11
11 - 20
3
Average
12 - 17
21 - 30
4
Hard
18 - 34
31 - 60
B
5
Very hard
35 - 50
61 - 90
A
Only use salt that has been specifically designed for dishwashers.
1. When measuring out the detergent
refer to the mentioned earlier information to add the proper quantity.
Inside the dispenser B there are
indications to help the detergent
dosing.
2. Remove detergent residues from
the edges of the dispenser and close the cover until it clicks.
3. Close the lid of the detergent
dispenser by pulling it up until the
closing device is secured in place.
After the salt has been poured into the machine, the SALT REFILL indicator light switches off.
The detergent dispenser automatically opens up at the right time
according to the program.
• Switch off the appliance by pressing the ON/OFF button.
Setting is complete!
As soon as this procedure is complete, run a program without loading.
If the salt container is not filled, the water softener and the
heating element may be damaged as a result.
2
EN
Drying
phase
PROGRAMS TABLE
Program
Detergent
container
Tub
B
Duration
of wash
program
(h:min)*)
Water
consumption
(litres/cycle)
Energy
consumption
(kWh/cycle)
3:20
12.0
1.04
1
Eco
50°
2
Intensive
65°
-
2:30
16.5
1.65
3
Normal
55°
-
2:00
16.0
1.35
4
Express 40’
50°
-
-
0:40
9.0
0.90
5
Soak
-
-
-
0:10
4.0
0.01
-
ECO program data is measured under laboratory conditions according to European Standard EN 50242.
Note for Test Laboratories: for information on comparative EN testing conditions, please send an email to the following address:
assistenza_en_lvs@indesitcompany.com
Pre-treatment of the dishes is not needed before any of the programs.
*) The duration of the program shown on the display or in the booklet is an estimate calculated on standard conditions. The actual time may vary
depending on many factors such as temperature and pressure of the incoming water, room temperature, amount of detergent, quantity and type of load,
load balancing, additional selected options and sensor calibration. The sensor calibration can increase program duration up to 20 min.
Standby consumption: Left-on mode consumption: 5 W - Off mode consumption: 0.5 W
PROGRAMS DESCRIPTION
Instructions on wash cycle selection.
1 ECO
5 SOAK
Normally soiled crockery. Standard program, the most efficient in
terms of its combined energy and water consumption.
Use to refresh crockery planned to be washed later. No detergent to be
used with this program.
2 INTENSIVE
Program recommended for heavily soiled crockery, especially suitable
for pans and saucepans (not to be used for delicate items).
3 NORMAL
For normally soiled dishes with dried food residues..
Notes:
Please note that cycles like Express or Fast are most effective for lightly
soiled dishes.
To reduce consumption even further, only run the dishwasher
when it is full.
4 EXPRESS 40’
Program to be used for lightly-soiled dishes with no dried food residues.
3
DAILY USE
1. CHECK WATER CONNECTION
Check that the dishwasher is connected to the water supply and
that the tap is open.
MODIFYING A RUNNING PROGRAM
3. LOAD THE RACKS
(see LOADING THE RACKS).
If a wrong program was selected, it is possible to change it, provided
that it has only just begun: press and hold the ON/OFF button, the
machine will switch off.
Switch the machine back on using the ON/OFF button and select the
new wash cycle and any desired options; start the cycle by pressing
the START/PAUSE button.
4. FILLING THE DETERGENT DISPENSER
(see PROGRAMS TABLE).
ADDING EXTRA CROCKERY
2. SWITCH ON THE DISHWASHER
Press the ON/OFF button.
5. CHOOSE THE PROGRAM AND CUSTOMISE THE CYCLE
Select the most appropriate program in accordance with the type
of crockery and its soiling level (see PROGRAMS DESCRIPTION) by
turning the PROGRAM SELECTION knob clockwise.
6. START
Start the wash cycle by pressing the START/PAUSE button.
When the program starts you hear a beep.
7. END OF WASH CYCLE
At the end of the wash cycle the END indicator light will switch on.
Switch off the appliance by pressing the ON/OFF button and open
the door.
Wait for a few minutes before removing the crockery - to avoid
burns. Unload the racks, beginning with the lower one.
Press the START/PAUSE button and open the door, taking care
to avoid the escaping steam, and place the crockery inside the
dishwasher. Press the START/PAUSE button: The cycle will start again
after a long beep has been emitted.
ACCIDENTAL INTERRUPTIONS
If the door is opened during the wash cycle or there is a power cut, the
cycle stops. It starts again from the point at which it was interrupted
once the door has been shut or the electricity supply is restored.
For more information about the functions, you can request or download
from the WEB a Use & Care Guide by following the instructions on the last
page.
The machine will switch off automatically during certain extended
periods of inactivity, in order to minimise electricity consumption.
If the crockery is only lightly soiled or if it has been rinsed with
water before being placed in the dishwasher, reduce the amount
of detergent used accordingly.
ADVICE AND TIPS
TIPS
UNSUITABLE CROCKERY
Before loading the baskets, remove all food residues from the crockery and empty the glasses. You do not need to rinse beforehand
under running water.
Arrange the crockery so that it is held in place firmly and does not tip
over; and arrange the containers with the openings facing downwards and the concave/convex parts placed obliquely, thus allowing
the water to reach every surface and flow freely.
Warning: lids, handles, trays and frying pans do not prevent the
sprayer arms from rotating.
Place any small items in the cutlery basket.
Very soiled dishes and pans should be placed in the lower basket because in this sector the water sprays are stronger and allow a higher
washing performance.
After loading the appliance, make sure that the sprayer arms can
rotate freely.
• Wooden crockery and cutlery.
• Delicate decorated glasses, artistic handicraft and antique crockery.
Their decorations are not resistant.
• Parts in synthetic material which do not withstand high temperatures.
• Copper and tin crockery.
• Crockery soiled with ash, wax, lubricating grease or ink.
The colours of glass decorations and aluminium/silver pieces can
change and fade during the washing process. Some types of glass
(e.g. crystal objects) can become opaque after a number of wash
cycles too.
HYGIENE
To avoid odour and sediment which can be accumulated in the dishwasher please run a high temperature program at least one a month.
Use a tea spoon of detergent and run it without the loading to clean
your appliance.
4
DAMAGE TO GLASS AND CROCKERY
• Only use glasses and porcelain guaranteed by the manufacturer as
dishwasher safe.
• Use a delicate detergent suitable for crockery
• Collect glasses and cutlery from the dishwasher as soon as the
wash cycle is over.
EN
LOADING THE RACKS
UPPER RACK
LOWER RACK
Load delicate and light dishes: glasses, cups, saucers, low salad bowls.
For pots, lids, plates, salad bowls, cutlery etc... Large plates and lids
should ideally be placed at the sides to avoid interferences with the
spray arm.
(loading example for the upper rack)
(loading example for the lower rack)
ADJUSTING THE HEIGHT OF THE UPPER RACK
The height of the upper basket can be adjusted: high position to place bulky crockery
in the lower basket and low position to
make the most of the tip-up compartments
by creating more space upwards.
The upper rack is equipped with a Upper
Rack height adjuster (see figure), without pressing the levers, lift it up by simply
holding the rack sides, as soon as the rack
is stable in its upper position. To restore to
the lower position, press the levers (A) at
the sides of the rack and move the basket
downwards.
CUTLERY BASKET
The basket is equipped with
top grilles for improved cutlery
arrangement. The cutlery basket
should be positioned only at the front
of the lower rack.
Knives and other utensils with
sharp edges must be placed in
the cutlery basket with the points
facing downwards or they must
be positioned horizontally in the
tip-up compartments on the upper
rack.
We strongly recommend that you do not adjust the height of the
rack when it is loaded.
NEVER raise or lower the basket on one side only.
FOLDABLE FLAPS WITH ADJUSTABLE POSITION
The side foldable flaps can be positioned at
three different heights to optimize the arrangement of crockery inside the rack.
Wine glasses can be placed safely in the
foldable flaps by inserting the stem of each
glass into the corresponding slots.
For optimum drying results incline the foldable flaps more. To change the inclination,
pull up the foldable flap, slide it slightly and
position it as you wish.
5
CARE AND MAINTENANCE
CLEANING THE FILTER ASSEMBLY
CLEANING THE SPRAY ARMS
Regularly clean the filter assembly so that the filters do not clog and
that the waste water flows away correctly.
The filter assembly consists of three filters which remove food residues
from the washing water and then recirculate the water: to obtain the
best washing results, you need to keep them clean.
On occasions, food residue may become encrusted onto the spray
arms and block the holes used to spray the water. It is therefore recommended that you check the arms from time to time and clean them
with a small non-metallic brush.
The dishwasher must not be used without filters or if the filter is
loose.
After several washes, check the filter assembly and if necessary clean it
thoroughly under running water, using a non-metallic brush and following the instructions below:
1. Turn the cylindrical filter A in an anti-clockwise direction and pull
it out (Fig 1).
2. Remove the cup filter B by exerting a slight pressure on the side
flaps (Fig 2).
3. Slide out the stainless-steel plate filter C (Fig 3).
To remove the upper spray arm, turn the plastic locking ring in an
anti-clockwise direction. The upper spray arm should be replaced so
that the side with the greater number of holes is facing upwards.
4. Inspect the trap and remove any food residues. NEVER REMOVE
the wash-cycle pump protection (black detail) (Fig 4).
1
2
B
A
A
The lower spray arm may be removed by pulling it upwards.
CLEANING THE WATER INLET HOSE
If the water hoses are new or have not been used for an extended
period of time, let the water run to make sure it is clear and free of
impurities before performing the necessary connections. If this
precaution is not taken, the water inlet could become blocked and damage the dishwasher.
C
3
4
After cleaning the filters, re-place the filter assembly and fix it in
position correctly; this is essential for maintaining the efficient
operation of the dishwasher.
6
EN
TROUBLESHOOTING
Your dishwasher may not work properly.
Before contacting the Service Centre check if the problem can be solved by going through the following list.
PROBLEMS
POSSIBLE CAUSES
SOLUTIONS
The dishwasher
won’t start
or does not
respond to commands.
The appliance has not been plugged in
properly.
Insert the plug into the socket.
Power outage.
The dishwasher starts automatically when the power returns.
The dishwasher door is not closed.
Vigorously push the door until you hear the “click”.
It does not respond to commands.
Switch off the appliance by pressing the ON/OFF button, switch it back on
after approximately one minute and reset the program.
The wash cycle has not finished yet.
Wait until the wash cycle finishes.
The drain hose is bent.
Check that the drain hose is not bent (see INSTALATION INSTRUCTION).
The sink drain pipe is blocked.
Clean the sink drain pipe.
The filter is clogged up with food residues.
Clean the filter (see CLEANING THE FILTER ASSEMBLY).
The dishes are rattling against each
Position the crockery correctly (see LOADING THE RACKS).
An excessive amount of foam has been
produced.
The detergent has not been measured out correctly or it is not suitable for
use in dishwashers (see FILLING THE DETERGENT DISPENSER). Reset dishwasher by pressing the DRAIN button (see OPTIONS AND FUNCTIONS) and run
new program without detergent.
The crockery has not been arranged
properly.
Arrange the crockery correctly (see LOADING THE RACKS).
The spray arms cannot rotate freely, being
hindered by the dishes.
Arrange the crockery correctly (see LOADING THE RACKS).
The wash cycle is too gentle.
Select an appropriate wash cycle (see PROGRAMS TABLE).
An excessive amount of foam has been
produced.
The detergent has not been measured out correctly or it is not suitable for use
in dishwashers (see FILLING THE DETERGENT DISPENSER).
The cap on the rinse aid compartment has
not been shut correctly.
Make sure the cap of the rinse aid dispenser is closed.
The filter is soiled or clogged.
Clean the filter assembly (see CARE AND MAINTENANCE).
There is no salt.
Fill the salt reservoir (see FILLING THE SALT RESERVOIR).
The dishwasher
won’t drain.
The dishwasher
makes
excessive noise.
The dishes are
not clean.
MAINTENANCE AND TROUBLESHOOTING GUIDE
CONTACTING AFTER-SALES SERVICE
For more information, maintenance procedures and troubleshooting,
see the Use and Care Guide
The Use and Care Guide can be obtained by:
• After-Sales Service; phone number see in warranty booklet.
• download from website: docs.indesit.eu
• use QR code
When you contact the After-Sales Service, you must provide the codes
shown on the rating plate attached to the left or right side inside the
door of the dishwasher. The phone number
is listed in the warranty booklet or on the
website: www.indesit.eu
IEC 436
:
TECHNICAL DATASHEET
The technical data containing the energy consumption data can be
downloaded from the website: docs.indesit.eu
7
400011308756
09/2018 mk - Xerox Fabriano
8
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising