Indesit | IDV 75 (KW) | Instruction for Use | Indesit IDV 75 (KW) Instruction for Use

Indesit IDV 75 (KW) Instruction for Use
Instruction manual
TUMBLE DRYER
Contents
EN
Installation, 2
EN
English, 1
FR
Français,41
AR
1 ،‫العربية‬
Where to install the tumble dryer
Ventilation
Electrical connections
Levelling the tumble dryer
Before you start your dryer
Warnings, 4
General safety
Saving energy and respecting the environment
Care and maintenance, 6
Disconnecting the power supply
Cleaning the filter after each cycle
Checking the drum after each cycle
Cleaning the tumble dryer
Description of the tumble dryer, 7
IDV 75
Front side
Rear side
Control panel
How to carry out a drying cycle
Starting a drying programme
ARDrying settings, 8
Drying times
Drying programmes and options
www.indesit.com
Troubleshooting, 9
Laundry
Assistance and Guarantee, 10
This symbol reminds you to read this
instruction manual.
!
Spare parts
Information on recycling and disposal
! Keep this manual at hand for immediate reference whenever
necessary. Always store this manual close to the tumble dryer and
remember to pass it on to any new owners when selling or transferring the appliance, so they may familiarise with the warnings
and suggestions herein contained.
! Read these instructions carefully: the following pages contain
important information on installation and useful suggestions for
operating the appliance.
1
Installation
If the dryer is installed below a worktop,
ensure there are 10 mm
between the upper panel
of the dryer and any
objects above it, and 15
mm between the sides
of the machine and the
walls or furniture units
15 mm
adjacent to it. This en15 mm
sures adequate air circulation. Make sure the
air inlets on the rear panel are not blocked or
obstructed.
dryer is used very often. The hose adaptor must be fitted
correctly, in order to prevent damp air from coming back into
the room.
B
Window ventilation hole
10 mm
EN
Where to install the tumble dryer
Ventilation
This appliance gently dries laundry by taking in cold, clean
and relatively dry air, heating it and passing it through the
fabric. To facilitate the drying process, damp air is expelled at
the rear, through a ventilation hose. When the dryer is in use,
there has to be adequate ventilation to avoid a back flow
of gases into the room from appliances burning other fuels,
including open fires.
Mobile ventilation system
When using the tumble dryer with the mobile ventilation
system, a ventilation hose must be connected. The hose
should be securely fastened to the ventilation hole at the
rear of the appliance (see “Description of the tumble dryer”).
We recommend the hose is connected to an outlet near
the tumble dryer, if possible. If it cannot be installed in a
permanent spot, the tumble dryer will still function perfectly
well if the ventilation hose is passed through a partiallyopened window.
Make sure you do not point the ventilation hose towards the
air inlet, which is located on the rear of the appliance.
The ventilation hose should not exceed a maximum length
of 2.4 metres; it should also be shaken frequently to remove
any fluff, dust or water deposits inside it. Make sure you do
not crush the hose.
Fixed ventilation system
We recommend the ventilation hose is connected to a
ventilation system for windows or doors, available from the
retailer which originally sold you the appliance or from your
local spare parts stockist.
Wall ventilation hole
1. Leave an opening in the wall to the left of the tumble dryer
installation site.
2. Make the hose as short and straight as possible, in order
to prevent any moisture from condensing and leaking back
into the appliance.
3. The hole in the wall must also be straight and pointing
downwards, so that the flow of air coming out is not
impeded.
Areas A and B should be checked frequently, to prevent
the accumulation of fluff or debris, particularly if the tumble
2
A
The ventilation hole should be
directly behind the dryer in order
to keep the hose as short as
possible.
Make sure you do not push the
tumble dryer too far backwards,
as this could lead to the
ventilation hose being crushed,
bent or even disconnected.
There should be no cuts, kinks or “U”-shaped bends
in the hose, as these could impede ventilation or trap
condensation.
The end of the hose must be facing downwards, in order to
prevent the hot, damp air from forming condensation in the
room or the tumble dryer.
Make sure that the tumble dryer is adequately ventilated,
and that the end of the ventilation hose is not pointing
towards the air inlet pipe on the
rear of the appliance.
The ventilation hose must
always be fitted to ensure
optimum performance.
Make sure that the ventilation
hose and the air inlet vents are
not obstructed or blocked.
Do not let the tumble dryer
recirculate exhaust air.
Improper use of the tumble dryer may result in fire hazards.
Ventilation through an open window
The air emitted by the tumble dryer must not be expelled in
the same duct as used for the fumes produced by different
appliances which burn gas or
other fuels.
Do not discharge the exhaust
air into an extraction system
or any duct with an extractor
fan. This will affect the way the
thermal controls operate and
can result in a fire hazard.
Make sure that the
room in which the tumble dryer is installed
is not damp, and that it is adequately
ventilated.
We do not recommend that the dryer is
installed in a cupboard but the dryer must
never be installed behind a lockable door, a
sliding door or a door with a hinge on the
opposite side to that of the dryer door.
The appliance must be installed with the
rear surface placed against a wall.
Electrical connections
Before plugging the appliance into the socket, check the following:
Make sure your hands are dry.
The socket must have an earth connection.
The socket must be able to withstand the
machine’s maximum power output as indicated on the rating plate (see Description of the
tumble dryer).
The power supply voltage must fall within
the values indicated on the rating plate (see
Description of the tumble dryer).
Do not use extension leads. Do not pull the
power supply cable. Do not use multiple plug
adaptors if the appliance is fitted with a plug.
For appliances with fitted plug, if the plug is
not suitable for you socket outlet, contact a
qualified technician.
EN
Levelling the tumble dryer
The tumble dryer should be installed level in order to
operate correctly.
Maximum load sizes: 7 kg
After installing the tumble dryer in its permanent position,
make sure it is level; check its side-to-side levelling first,
followed by front-to-back.
If the tumble dryer is not perfectly level, use a wooden block
to support it while you adjust the two front feet, up or down
as necessary.
Before you start your dryer
Once the tumble dryer is installed, clean the inside of the drum
before operating it and remove any dirt accumulated during
transportation.
The dryer must not be installed outdoors,
even if the space is sheltered.
Once installed, the dryer’s electrical wire
and plug must be within reach.
The power cord must not be bent or
squashed.
If the plug being replaced is a nonrewirable type, then the cut-off plug must be
disposed of safely. DO NOT leave it where it
can be inserted into a socket and create a
shock hazard.
Power consumption
off-mode (Po) - Watts
0.00
left-on mode (Pl) - Watts
N/A
Programs
Kg
kWh
Minutes
Standard cotton*
7
4.08
113
Standard cotton
3.5
2.10
64
Synthetics
3
1.11
40
* This is the reference program for the energy label
and suitable to dry normal wet cotton laundry. This
is the most efficient programme in terms of energy
consumption for drying wet cotton laundry.
The electric cord must be regularly
checked. If the supply cord is damaged, it
must be replaced by service agent. (see
Service).
The manufacturer denies any
responsibility should any of these rules not be
followed.
If in doubt about any of the above
consult a qualified electrician.
3
Warnings
EN
! This appliance has been designed and built according to
international safety standards. These warnings are given for
safety reasons and must be followed carefully.
General safety
•This appliance can be used by children
aged from 8 years and above and
persons with reduced physical, sensory or
mental capabilities or lack of experience
and knowledge if they have been given
supervision or instruction concerning use of
the appliance in a safe way and understand
the hazards involved.
• This tumble dryer has been designed for
home, and not professional, use.
• Do not touch the appliance while barefoot
or with wet hands or feet.
• Unplug the machine by pulling on the plug,
not the cord.
•Children should be supervised to ensure
that they do not play with the dryer.
•Cleaning and user maintenance shall not be
made by children without supervision.
•Children of less than 3 years should be
kept away from the appliance unless
continuously supervised.
• The appliance must be installed correctly
and have proper ventilation. The air intake
vents behind the machine, the outlet
vents and the vent tube should never be
obstructed (see Installation).
• Never direct the vent tube outlet towards
the air intake at the back of the machine.
• Never allow the tumble dryer to recycle
exhaust air.
• Never use the dryer on carpeting where the
pile height would prevent air from entering
the dryer from the base.
• Check to see if the dryer is empty before
loading it.
•
The back of the dryer could become very
hot. Never touch it while in use.
• Do not use the dryer unless the filter, is
securely in place (see Maintenance).
• Do not overload the dryer (see Laundry for
maximum loads).
• Do not load items that are dripping wet.
•C
� arefully check all instructions on clothing
labels (see Laundry).
• Do not tumble dry large, very bulky items.
• Do not tumble dry acrylic fibres at high
temperatures.
• Do not turn off the dryer when there are still
4
warm items inside.
• Clean the filter after each use (see
Maintenance).
• Do not allow lint to collect around the dryer.
• Never climb on top of the dryer. It could
result in damage.
• Always follow electrical standards and
requirements (see Installation).
• Always buy original spare parts and
accessories (see Service).
To minimise the risk of fire in your tumble
dryer, the following should be observed:
• Tumble dry items only if they have been
washed with detergent and water, rinsed
and been through the spin cycle. It is a fire
hazard to dry items that HAVE NOT been
washed with water.
• �Do not dry garments that have been treated
with chemical products.
• Do not tumble dry items that have
been spotted or soaked with vegetable
or cooking oils, this constitutes a fire
hazard. Oil-affected items can ignite
spontaneously,especially when exposed to
heat sources such as a tumble dryer. The
items become warm, causing an oxidisation
reaction with the oil, Oxidisation creates
heat. If the heat cannot escape, items can
become hot enough to catch fire. Piling,
stacking or storing oil-effected items can
prevent heat from escaping and so create
a fire hazard.If it is unavoidable that fabrics
containing vegetable or cooking oil or those
that have been contaminated with hair care
products be placed in a tumble dryer they
should first be washed with extra detergent
- this will reduce, but not eliminate the
hazard. They should not be removed from
the dryer and piled or stacked while hot.
• Do not tumble dry items that have
previously been cleaned in or washed in,
soaked in or soiled with petrol/gasoline,
dry cleaning solvents or other flammable
or explosive substances. Highly flammable
substances commonly used in domestic
environments including cooking oil,
acetone, denatured alcohol, kerosene,
spot removers, turpentine, waxes and wax
removers. Ensure these items have been
washed in hot water with an extra amount
of detergent before being dried in the
tumble dryer.
• �Do not tumble dry items containing foam
rubber (also known as latex foam), or
similarly textured rubber like materials.
Foam rubber materials can, when heated,
produce fire by spontaneous combustion.
• �Fabric softener or similar products should
not be used in a tumble dryer to eliminate
the effects of static electricity unless the
practice is specifically recommended by the
manufacturer of the fabric softener product.
• Do not tumble dry undergarments that
contain metal reinforcements eg. bras
with metal reinforcing wires. Damage to
the tumble dryer can result if the metal
reinforcements come loose during drying.
• �Do not tumble dry rubber, plastic articles
such as shower caps or babies waterproof
covers, polythene or paper.
• Do not tumble dry rubber backed articles,
clothes fitted with foam rubber pads,
pillows, galoshes and rubber coated tennis
shoes.
• Remove all objects from pockets such as
lighters and matches.
EN
WARNING: Never stop the dryer before the
end of the drying cycle unless all items are
quickly removed and spread out so that the
heat is dissipated.
Save energy and respect the environment
• Wring out all items to eliminate excess water before
tumble drying (if you use a washing machine first, select
a high spin cycle). Doing this will save time and energy
during drying.
• Always dry full loads - you save energy: single items or
small loads take longer to dry.
• Clean the filter after each use to contain energy
consumption costs (see Maintenance).
5
Care and maintenance
EN
Disconnecting the power supply
! Disconnect the dryer when not in use or
during cleaning and maintenance operations.
Cleaning the filter after each cycle
The filter is a fundamental component of the
dryer: its function is to collect lint and fluff that
form during drying.
Clean the filter once drying is completed, by
rinsing it under running water or cleaning it
with a vacuum cleaner. Should the filter become clogged, the flow of air inside the dryer
will be seriously hampered: drying times becomes longer and more energy is consumed.
Moreover, the dryer may become damaged.
The filter is located
behind of the dryer seal
(see Picture).
Removing the filter:
1. Pull the filter’s plastic
handle upwards (see
Picture).
2. Clean the fluff off
the filter and replace it
correctly. Ensure that
the filter is pushed fully
home.
! Do not use the dryer unless
the filter has been replaced in
its holder.
Checking the drum after each cycle
Rotate the drum manually to remove smaller items (handkerchiefs) that could have been left inside the dryer.
Cleaning the drum
! Avoid using abrasives, steel wool or stainless steel cleaning
agents to clean the drum.
A coloured film may appear on the stainless steel drum
surface: it may be caused by a combination of water and/or
cleaning agents such as fabric conditioners. This coloured
film does not affect the dryer’s performance.
Cleaning the tumble dryer
• The external metal and plastic parts and the rubber parts
can be cleaned with the aid of a damp cloth.
• Periodically check the vent hose and all other parts of the
venting system and remove any accumulations of fluff and
lint.
6
! Do not use solvents or abrasives.
! Have the dryer checked regularly by authorised technical
personnel in order to ensure that the electrical and mechanical parts work safely (see Assistance).
Description
of the tumble dryer
Front side
Rear side
Control panel
Serial number
and model
number
Drum
Filter
Control panel
Rating Plate
Caution, high
temperature
High Heat
button
EN
Air inlet
Connection for
ventilation hose
Start
button
Drying time selector
knob
Drying time selector knob
This is used to set the drying time: turn the knob in a clockwise direction until the indicator is set to the desired drying time (see
Drying settings). Do not attempt to turn the knob anticlockwise.
High Heat button
It can be used to customise the selected programme in accordance with your own requirements.
START button
Press the button to begin drying.
How to carry out a drying cycle
Starting a drying programme
1. Plug the dryer into the power supply socket.
2. Select a suitable drying programme for the type of laundry (see Laundry).
3. Open the door, ensure that the filter is clean and securely placed.
4. Load the machine, making sure that no piece of laundry gets between the door and the door seal. Close the door.
5. Turn the “Drying time selector” knob until the indicator is pointing towards the most suitable drying time for the type of fabric in
that load. Use the table to check the relationship between fabric type and load capacity (see Drying settings), and make sure you
are familiar with the instructions provided for each type of fabric (see Laundry). Do not attempt to turn the knob anticlockwise.
6. If necessary, set the temperature using the HIGH HEAT button.
7. Press the START button to start the drying cycle.
Laundry can be checked while the drying programme runs and any garments already dry can be removed, while drying continues
for the remaining items. After closing the door, press the START button to resume machine operation.
8. The final COOL TUMBLE phase (i.e. the fabrics are cooled) activates during the last few minutes of the drying programme; always
allow this phase to terminate.
9. Open the door, remove the laundry then clean the filter and replace it.
10. Disconnect the dryer from the power supply.
7
Drying settings
EN
Drying times
The drying time depends on the size of the load and on the type of fabric it contains (see Table).
The COOL TUMBLE cycle runs during the final 10 minutes of the programme.
! For large loads, select the High Heat option if available.
Fabric
Standard Cotton –
high heat
Synthetics –
higt heat
Acrylics –
low heat
Load
1 kg
2 kg
3 kg
4 kg
5 kg
6 kg
7 kg
20 - 30
minutes
35 - 45
minutes
45 - 60
minutes
60 - 70
minutes
70 - 80
minutes
80 - 100
minutes
90 - 120
minutes
20 - 30
minutes
35 - 45
minutes
45 - 60
minutes
-
-
-
25 - 40
minutes
40 - 60
minutes
-
-
-
-
Drying times are approximate and may vary depending on the following:
•
•
•
•
Amount of water retained by items after the spin cycle: towels and delicate items retain a lot of water.
Fabrics: items of the same fabric, but with different texture and thickness may have different drying times.
Amount of laundry: single items and small loads will take a short time to dry.
Drying: if items are to be ironed, they can be removed from the dryer while still slightly damp. Items that require complete drying
can be left longer.
• Temperature of the room: the lower the temperature of the room, the longer it will take for the dryer to dry clothing.
• Bulk: certain bulky items require special care during the drying process. We suggest removing these items and replacing them in
the dryer once they have been shaken out: repeat this procedure several times during the course of the drying cycle.
! Do not over-dry items.
All fabrics contain natural dampness which helps to keep them soft and fluffy.
Drying programmes and options
Refresh
A short programme suitable for refreshing fibres and garments through the emission of cool air. It lasts about 10 minutes.
! As this is not a drying programme, it is not to be used for garments that are still wet.
High Heat button
The high heat button selects the drying temperature. When the button is out low heat is selected and when it is pushed in high heat
is selected
8
Troubleshooting
If you feel that the dryer is not working properly, consult the following troubleshooting suggestions before contacting the Technical
Assistance Centre (see Assistance).
Problem:
EN
Possible causes / Solutions:
The dryer does not start.
The dryer does not start.
• The plug has not been inserted far enough into the socket to make contact.
• There has been a power cut.
• The fuse has blown. Try connecting another appliance to the same socket.
• If an extension cord is used, try connecting the dryer plug directly into the socket.
• The door has not been closed properly.
• The programme has not been set correctly (see How to carry out a drying cycle).
• The START button has not been pressed (see How to carry out a drying cycle).
The filter has not been cleaned (see Care and maintenance).
An incorrect drying time was selected for the type of load (see Laundry).
The items are too wet (see Laundry).
The dryer is overloaded (see Laundry).
The flexible ventilation hose may be blocked (see Installation).
The air inlet may be blocked or obstructed (see Installation).
The fixed ventilation flap, on the protective weatherproof cover, may be obstructed
(see Installation).
Drying times are too long.
•
•
•
•
•
•
•
Laundry
• This is normal, especially if the dryer has not been used for a long time. If the noise
persists during the entire cycle, contact the Technical Assistance Centre.
The dryer is noisy during the first few
minutes of operation.
Laundry
Sorting laundry
Drying times
• Check the symbols on the care labels of the various garments to verify whether the garments can be safely tumble
dried.
• Sort laundry according to the type of fabric.
• Empty all pockets and check for loose buttons.
• Close zips and hooks and fasten belts and strings without
tightening them.
• Wring out garments to remove the maximum amount of
water possible.
Drying times are approximate and may vary depending on
the following:
! Do not load the dryer when garments are dripping wet.
Maximum load sizes
Do not overload the drum.
The following values indicate the weight of dry garments:
Natural fibres: maximum 7 kg
Synthetic fibres: maximum 3 kg
! Do not overload the dryer as this may result is reduced
drying performance.
Care labels
Always check the care labels, especially when placing
garments in the tumble dryer for the first time. Below are the
most commonly used symbols:
May be tumble dried.
Do not tumble dry.
Tumble dry – high heat.
Tumble dry – low heat.
• Amount of water retained by items after the spin cycle:
towels and delicate items retain a lot of water.
• Fabrics: items of the same fabric, but with different texture
and thickness may have different drying times.
• Amount of laundry: single items and small loads may take
longer to dry.
• Drying: if items are to be ironed, they can be removed
from the dryer while still slightly damp. Items that require
complete drying can be left longer.
• Heat setting.
• Temperature of the room: the lower the temperature of the
room, the longer it will take for the dryer to dry clothing.
• Bulk: certain bulky items require special care during the
drying process. We suggest removing these items and
replacing them in the dryer once they have been shaken
out: repeat this procedure several times during the course
of the drying cycle.
! Do not over-dry items.
All fabrics contain natural dampness which helps to keep
them soft and fluffy.
The drying times provided refer to the automatic Cupboard
dry programmes.
The Timed drying settings are also indicated to enable you
to select the most suitable timed option.
The weight refers to dry items.
9
Assistance
EN
Before contacting the Technical Assistance Centre:
Spare parts
• Follow the troubleshooting guide to check whether problems can be solved personally (see Troubleshooting).
• If not, switch the dryer off and contact the Technical Assistance Centre closest to you.
This dryer is a complex machine. Attempting to repair it
personally or employing an unqualified service agent may put
the safety of people at risk, damage the machine or invalidate the spare parts guarantee.
Always contact a qualified technician when experiencing
problems with this machine.
Provide the following data when contacting the Technical Assistance Centre:
• name, address and postal code
• telephone number
• type of malfunction
• date of purchase
• the appliance model (Mod.)
• the dryer’s serial number (S/N)
This information can be found on the data plate located
behind the door.
Product Guarantee And Repair Information
Guarantee
12 Months Parts and Labour Guarantee
Your appliance has the benefit of our manufacturer’s guarantee, which covers the cost of breakdown repairs for twelve months from the
date of purchase.
This gives you the reassurance that if, within that time, your appliance is proven to be defective because of either workmanship or
materials, we will, at our discretion, either repair or replace the appliance at no cost to you:
This guarantee is subject to the following conditions:
- The appliance has been installed and operated correctly and in accordance with our operating and maintenance instructions.
- The appliance is used only on the electricity or gas supply printed on the rating plate.
- The appliance has been used for normal domestic purposes only.
- The appliance has not been altered, serviced, maintained, dismantled, or otherwise interfered with by any person not authorised by us.
- Any repair work must be undertaken by us or our appointed agent.
- Any parts removed during repair work or any appliance that is replaced become our property.
- The appliance is used in the United Kingdom or Republic of Ireland.
The guarantee does not cover:
- Damage resulting from transportation, improper use, neglect or interference or as a result of improper installation.
- Replacement of any consumable item or accessory. These include but are not limited to: plugs, cables, batteries, light bulbs, fluorescent
tubes and starters, covers and filters.
- Replacement of any removable parts made of glass or plastic.
THIS
GUARANTEE WILL
NOT APPLY IF THE
HAS BEEN USED IN COMMERCIAL OR NON-DOMESTIC PREMISES.
Information
on recycling
andAPPLIANCE
disposal
As part of
ourAfter
continual
Repairs
and
Salescommitment towards environmental protection, we reserve the right to use recycled quality components to
reduce
costs
for and
our customers
and to
minimise
wastage.
For
product
help
advice, repairs,
spare
parts materials
or accessories,
we’re here to help.
For
local repairofengineers
- 03448
111 606follow
ROI -local
0818regulations
313 413 UK
standard
local rateofapplies
ROI local
Irish rate applies
• Disposing
the packaging
materials:
to allow
for recycling
packaging
materials.
For
Parts
and
parts.indesit.co.uk/shop
• In
order
to Accessories
minimise thevisit:
risk of
injury to children, remove the door and plug, then cut the power supply cord flush with the apPlease
remember
to register
your
appliance
at www.indesitservice.co.uk
tobeing
activate
your 10 year
parts guarantee.
pliance.
Dispose
of these
parts
separately
to prevent the appliance from
connected
to a power
supply socket.
Please note, our advisors will require the following information: model number, serial number.
This
information
can household
be found on the
data plate located behind the door.
Disposal
of old
appliances
European Directive 2012/19/EC concerning Waste Electrical and Electronic Equipment (WEEE) states that household
appliances should not be disposed of using the normal solid urban waste cycle. Exhausted appliances should be collected
separately in order to optimise the cost of re-using and recycling materials comprising the machine, while preventing
potential damage to public health and the environment. The crossed-out wheeled bin symbol appears on all products to
remind owners of the obligations regarding separate waste collection.
Owners should contact their local authorities or appliance dealers for further information concerning the correct disposal of household appliances.
This appliance has been designed, constructed and distributed in compliance with the
requirements of European Directives:
- LVD 2014/35/EU, EMC 2014/30/EU and RoHS 2011/65/EU.
10
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising