Whirlpool | UW8 F2D WBI N | Setup and user guide | Whirlpool UW8 F2D WBI N Setup and user guide

Whirlpool UW8 F2D WBI N Setup and user guide
QUICK START GUIDE
SMART DISPLAY
This optional function can be used to save energy. To activate the Smart
Display, press the buttons
and together for 3 seconds until an
audible signal sounds.
To deactivate this function repeat the same procedure.
Remember that this function does not disconnect the appliance from the
power supply, but only reduce the power consumed by external display
(see the Instructions for Use).
2
3
10
4
5
6
FAST FREEZE indicator (see the Instructions for Use).
7
11
ON/STANDBY indicator /button
To put the product in Stand-by, press and hold for 3 seconds. All the icons
turn off except On/Standby indicator . To reactivate the appliance press
once (briefly) this button.
8
9
12
BLACK OUT ALARM
Long Black-out Alarm indicator. (see the Instructions for Use)
TEMPERATURE DISPLAY
1. Control panel
2. Light (LED system)
3. Ice packs*
4. Ice Mate* or Ice tray*
5. Drawer divider*
6. Bottle rack*
7. Glass shelves
8. Rating plate with commercial name
9. Door reversibility kit
10. Area for freezing fresh food or to store
frozen food
11. Area for storing frozen foods
12. Door seal
TEMPERATURE SETTING button
The appliance is normally factory-set for operation at the recommended
temperature of -18°C. The internal temperature can be adjusted between
-16°C and -24°C, proceeding as follows:
• Press to change the set point (°C). The storage temperature can be
changed by -1°C with each pressure of the button: the value changes
cyclically between -16°C and -24°C.
HOW TO REVERSE DOOR SWING
- see enclosed Instructions for Use (Version_1)
Is recommended to reverse door swing by two
persons.
There is not foreseen door reversibility for:
- models with integrated handle
- models with glass panel on the door.
Specifications, technical data and images
may vary from model to model.
ECO NIGHT FUNCTION (NIGHT TIME RATE) / PARTY MODE button
Eco Night function
Press to activate/deactivate the Eco Night function. The Eco Night function enables
appliance energy consumption to be concentrated in the reduced rate hours, generally
at night (see the Instructions for Use)
Party Mode
To activate / deactivate the Party Mode function, press the Stop Alarm button for 3
seconds. In case of Party Mode alarm to deactivated press the Stop Alarm button.
PARTY MODE indicator (see the Instructions for Use).
6th SENSE FREEZE CONTROL
6th Sense Freeze Control is an advanced technology that reduces freeze
burns and food preserves its original quality and color.
* Available on selected models
HOW TO START THE APPLIANCE
After plugging the appliance to the mains, it starts
the operation automatically. After starting the
appliance, wait at least 4-6 hours before placing food
into the appliance. When the appliance is connected
to the power supply, the display lights up and all
the icons appear on the display for approximately 1
second.
The default (factory) values of the freezer
compartment settings light-up.
STOP ALARM button
Press in case of alarm (see the below Alarm Table).
ALARMS TABLE
ALARMS TYPE
Signal
Door open alarm
The acoustical alarm is activated and the Alarm Indicator
Temperature alarm
The Temperature display blinks (°C) and the Alarm Indicator
Party Mode Alarm
The Party Mode Indicator
blinks.
remains on.
blinks and the acoustical alarm is activated.
Cause
Cure
The door has remained open for more than 2 minutes.
Close the door or press the Stop Alarm to mute the acoustical alarm.
The inside temperature is not adequate.
Press the Stop Alarm button ; the acoustical alarm stops, the Temperature Display (°C)
remains on until a temperature < -10°C is reached.
blinks and the Alarm Indicator
30 min. elapsed since Party Mode function has been activated. It is time to take out the
bottle from the freezer ( see Instructions for Use for more details).
Press the Stop Alarm button
and remove the bottle from the freezer.
Long Black-Out alarm
remains on, the Alarm indicator
blinks and the
The Black Out Alarm icon
Temperature display (°C) blinks, showing the maximum temperature reached during
blackout.
Prolonged power failure, able to cause the inside temperature to increase to 0°C.
Press the Stop Alarm button ; the acoustical alarm stops, the Temperature Display (°C)
remains on until a temperature < -10°C is reached.
blinks and the Alarm Indicator
Malfunction
The letter “F” blinks on the display (°C).
Product malfunction.
Contact the After-sales Service.
DA
FI
IT
NO
PT
SV
GB
Printed in Italy
1
FREEZE CONTROL / FAST FREEZE button
Freeze Control
Freeze Control is an advanced technology that reduces temperature fluctuations in the
whole freezer compartment to minimum.
To activate/deactivate the Freeze Control function simply press FREEZE CONTROL button.
If the function is engaged and the user modify the freezer temperature out of the working
range, the function is automatically switched off.
In case of Fast freezing is engaged, the function “Freeze control” is inhibited until the Fast
Freezing function switched off.(see the Instructions for Use)
Fast Freeze
Press for 3 seconds to activate/deactivate the Fast Freeze function (see the Instructions
for Use).
The Fast Freeze function switches off automatically after 50 hours.
06/16 - Whirlpool® Registered trademark/TM Trademark of Whirlpool group of companies - © Copyright Whirlpool Europe s.r.l. 2014. All rights reserved - http://www.whirlpool.eu
Read the Instructions for Use carefully before
using the appliance.
EN
19514700100
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising