Whirlpool | KWXXXB 14600 | Product technical drawing | Whirlpool KWXXXB 14600 Product technical drawing

Whirlpool KWXXXB 14600 Product technical drawing
80
8
6
5
0
56
595
550
455
583 - 585
402
548
9
133
544
132
595
8
80
24
KWXXXB 14600
12NC/Fx: 851349996000
DIMENSION
OVERALL CABINET
MIN Height of the wall cabinet niche, including all required space for installation or ventilation
MIN Height of the tall cabinet niche, including all required space for installation or ventilation
MIN Height of the base cabinet niche, including all required space for installation or ventilation
MAX Height of the wall cabinet niche, including all required space for installation or ventilation
MAX Height of the tall cabinet niche, including all required space for installation or ventilation
MAX Height of the base cabinet niche, including all required space for installation or ventilation
MIN Width of the wall cabinet niche, including all required space for installation or ventilation
MIN Width of the tall cabinet niche, including all required space for installation or ventilation
MIN Width of the base cabinet niche, including all required space for installation or ventilation
MAX Width of the wall cabinet niche, including all required space for installation or ventilation
MAX Width of the tall cabinet niche, including all required space for installation or ventilation
MAX Width of the base cabinet niche, including all required space for installation or ventilation
MIN Depth of the wall cabinet niche, including all required space for installation or ventilation
MIN Depth of the tall cabinet niche, including all required space for installation or ventilation
MIN Depth of the base cabinet niche, including all required space for installation or ventilation
Space in front, which is required to install bottom trim
Indicates whether a ventilation opening is needed or not. Default is "N"
WALL CABINET (vent-shaft incoming)
Indicates the position of the freespace for the inbound airflow (wall cabinet)
Minimum space or inbound ventilation (wall cabinet)
Minimum area for inbound ventilation cavity (wall cabinet)
WALL CABINET (vent-shaft outgoing)
Indicates the position of the freespace for the outbound airflow (wall cabinet)
Minimum space or outbound ventilation (wall cabinet)
Minimum area for outbound ventilation cavity (wall cabinet)
TALL CABINET (vent-shaft incoming)
Indicates the position of the freespace for the inbound airflow (tall cabinet)
Minimum space for inbound ventilation (tall cabinet)
Minimum area for inbound ventilation cavity (tall cabinet)
TALL CABINET (vent-shaft outgoing)
Indicates the position of the freespace for the outbound airflow (tall cabinet)
Minimum space for outbound ventilation (tall cabinet)
Minimum area for outbound ventilation cavity (tall cabinet)
BASE CABINET (vent-shaft incoming)
Indicates the position of the freespace for the inbound airflow (base cabinet)
Minimum space for inbound ventilation (base cabinet)
Minimum area for inbound ventilation cavity (base cabinet)
BASE CABINET (vent-shaft outgoing)
Indicates the position of the freespace for the outbound airflow (base cabinet)
Minimum space for outbound ventilation (base cabinet)
Minimum area for outbound ventilation cavity (base cabinet)
MEASURE
0
583
0
0
585
0
0
560
0
0
568
0
0
550
0
8
Yes
mm
mm
mm
mm
mm
mm
mm
mm
mm
mm
mm
mm
mm
mm
mm
mm
Rear
0
mm
0
cm²
0
0
mm
cm²
Rear
80
mm
400 cm²
Rear
80
mm
400 cm²
0
0
mm
cm²
0
0
mm
cm²
DIMENSION
GTIN (EAN) code:
8003437223334
MEASURE
APPLIANCE
Height of the front
Width of the front
Depth of the front
Maximum depth all protruding elements, e.g. handles, controls
Lateral clearance between front edge and most protruding elements which avoid to open a
neighbour front more than 90 degrees
Projection of front in relation to housing of appliance
Projection of front in relation to bearing area of the appliance. Taken at minimum height of
appliance, if height is adjustable
When product panel is missing, set to 0
Space in front, which is required to guarantee full operability. The most protruding part gives this
dimension
Height from bearing area of appliances and lower handle
Frontal handle thickness
Frontal handle width
MIN Height of the product body
MAX Height of the product body
Width of the product body
Depth of the product body
Full depth of product excluding protruding interface elements
Appliance can be used as base for other appliances from the same manufacturer. Default is "No"
Appliance Flap door
Projection of the opened flap in relation to bearing area
Maximum angle when flap door is opened totally
Appliance Side swing door
Lateral projection of front incl. controls when door is opened totaly. At the side where the hinge is
mounted
Lateral projection of opened front at the side where the hinge is fixed
Maximum angle when door is opened totally
Appliance other
Depth from front end of the niche to the front end of the freespace of the retrace
Height from niche to bottom end of freespace for the retrace
455
595
24
0
0
mm
mm
mm
mm
mm
9
8
mm
mm
132
402
mm
mm
0
0
0
133
133
548
544
568
Yes
mm
mm
mm
mm
mm
mm
mm
mm
mm
mm
mm
mm
mm
mm
mm
0
0
mm
mm
0
mm
0
0
mm
mm
0
0
mm
mm
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising