Bauknecht | FBWF71485BW EU | Setup and user guide | Bauknecht FBWF71485BW EU Setup and user guide

Bauknecht FBWF71485BW EU Setup and user guide
Quick Guide
EN
THANK YOU FOR PURCHASING A BAUKNECHT PRODUCT.
To receive more comprehensive assistance, register the
appliance on
www.bauknecht.eu/register
Before using the appliance carefully read the Health and Safety guide.
Before using the machine, it is imperative that the transport bolts are removed. For more
detailed instructions on how to remove them, see the Installation Guide.
CONTROL PANEL
1. ON/OFF button
2. CHILD LOCK button
3. CLEANING ACTION button
4. CLEANING ACTION indicator lights
5. START/PAUSE button and indicator light
6. OPTION button and indicator light
7. DELAY START button
8. SPIN button
9. TEMPERATURE button
10. WASH CYCLE SELECTOR KNOB
1
2
3
6
5
4
DISPLAY
9
10
8
7
WASH CYCLE TABLE
Energy consumption kWh
Total water l
Recommended
detergent
Residual
dampness %
Maximum load 7 kg
Power input in off mode 0.5 W / in left-on mode 8 W
1
Anti-Stain
40 °C
- 40 °C
1400
7,0
**




–
–
–
–
2
Anti-Stain 45‘
40 °C
- 40 °C
1200
3,5
**
–


–

–
–
–
3
Whites
60 °C
- 90 °C
1400
7,0
**




–
–
–
–
4
Bed&Bath
60 °C



–
–
–
–
0,76 52,5
Temperature
Wash cycle
5
Eco cotton
60°/40°
Default
(1)
60 °C
Range
Detergents and Additives
Fabric
Maximum
Maximum Duration Prewash Wash softener Powder Liquid
spin
load (kg) (minutes)
(r.p.m.)
1
2
3
- 60 °C
1400
7,0
**

60° C
1400
7,0
240
–




53
40°C
1400
7,0
230
–




53
0,97
75
6
Mixed
40 °C
- 40 °C
1000
3,5
**
–


–

–
–
–
7
Cotton (2)
40 °C
- 60 °C
1400
7,0
230
–



–
53
0,97
75
8
Synthetics (3)
40 °C
- 60 °C
1200
4,0
195




–
33
0,75
72
9
Colours
40 °C
- 40 °C
1400
7,0
**




–
–
–
–
10
Rapid 30'
30 °C
- 30 °C
800
3,0
30
–


–

71
0,19
29
11
Wool
40 °C
- 40 °C
800
1,5
**
–


–

–
–
–
12
Darks
30 °C
- 30 °C
800
4,0
**
–


–

–
–
–
13
Ultra-delicate
30 °C
- 30 °C
--
1,0
**
–


–

–
–
–
14
Duvets
30 °C
- 30 °C
1000
2,0
**
–


–

–
–
–
Rinse
–
–
1400
7,0
**
–
–

–
–
–
–
–
Spin & Drain *
–
–
1400
7,0
**
–
–
–
–
–
–
–
–
 Required dosage  Optional dosage
The cycle duration indicated on the display or instruction manual is an estimate based on
standard conditions. The actual duration may vary in relation to several factors, such as
the temperature and pressure of the incoming water, ambient temperature, amount of
detergent, load quantity and type, load balancing and any additional options selected.
For all testing institutes:
2) Long cotton cycle: set cycle 7 at a temperature of 40°C.
3) Long synthetics cycle: set cycle 8 at a temperature of 40°C.
1) Test wash cycle in compliance with regulation 1061/2010:
This cycle is designed for normally soiled cotton loads and is the most efficient in terms of
both electricity and water consumption; it should be used for garments washable at 60°C or
at 40°C. The actual washing temperature may differ from the indicated value.
PRODUCT DESCRIPTION
1. Top
2. Detergent dispenser drawer
3. Control panel
4. Handle
5. Porthole door
6. Drain pump (behind the plinth)
7. Plinth (removable)
8. Adjustable feet (2)
* By selecting the cycle and excluding the spin cycle, the washing machine will drain only.
** The duration of the wash cycles can be checked on the display.
DETERGENT DISPENSER DRAWER
1.
2.
3.
4.
5.
6.
7.
8.
Compartment 1: Prewash detergent (powder) B
Compartment 2: Washing detergent (powder
or liquid)
If liquid detergent is used, the removable plastic
partition A (supplied) should be used for proper
dosage.
If powder detergent is used, place the partition
into slot B.
Compartment 3: Additives (fabric softeners,
etc.)
The fabric softener must not exceed the “MAX” level.
A
1
3
2
WASH CYCLES
Follow the instructions on the symbols of the garment’s wash
care label. The value indicated in the symbol is the maximum
recommended temperature for washing the garment.
Anti-Stain
This cycle is suitable to heavily-soiled garments with resistant colours. It
ensures a washing class that is higher than the standard class (A class).
When running the programme, do not mix garments of different colours.
We recommend the use of powder detergent. Pre-treatment with special
additives is recommended if there are obstinate stains
Anti-Stain 45’
This cycle is ideal for washing daily stains in 45’. It is ideal for mixed fabrics
and coloured garments.
Whites
For heavily soiled whites and resistant colours.
Bed&Bath
For washing home linen in a single cycle. It optimises the use of fabric
softener and allows for saving time and electricity. We recommend the
use of powder detergent.
Eco cotton
Suitable for washing moderately soiled cotton garments. At 40°C and
60°C it is the standard cycle for washing cotton garments, and is the most
efficient in terms of combined water and electricity consumption.
Mixed
To wash mixed and coloured items together.
Cotton
Suitable for washing towels, underwear, table cloths, etc. made of
resistant linen and cotton that are moderately to heavily soiled.
Synthetics
Suitable for washing moderately soiled garments made of synthetic fibres
(e.g. polyester, polyacrylic, viscose, etc.) or mixed synthetic-cotton fibres.
Colours
For washing coloured cotton garments. This programme is optimised to
keep colours bright even after repeated washing.
Rapid 30’
For washing lightly soiled garments in a short time. Not suitable for wool,
silk and garments to be washed by hand.
Wool - Woolmark Apparel Care - Green:
The “Wool” wash cycle is approved by the Woolmark
Company for washing wool garments classified as
“hand-washable”, provided that the wash complies with
the instructions appearing on the garment’s label and
with those provided by the manufacturer of this washing
machine. (M1126)
Darks
For washing dark-coloured garments. The wash cycle is designed to
preserve dark colours over time.
We recommend using a liquid detergent for best results, preferably when
washing dark-coloured garments.
Ultra-delicate
For washing very delicate garments. It is advisable to turn the garments
inside out before washing them. For best results, use liquid detergent on
delicate garments.
Duvets
Suitable for washing clothing padded with goose down, such as single
duvets (weighing under 2 kg), cushions or down jackets. Duvets should
be loaded into the drum with their edges folded inwards and no more
than ¾ of the total drum volume should be used up. For best results, it is
advisable to use liquid detergent to be poured into the detergent drawer.
Rinse
Designed for rinsing and spinning.
Spin & Drain
Designed for spinning and draining the water.
DISPLAY
The display is useful when programming the washing machine and
provides plenty of information.
The duration of the available wash cycles and the remaining time of a
running cycle appear (the display will show the maximum duration of the
cycle chosen, which may decrease after several minutes, since the
effective duration of the programme varies depending on the wash load
and the settings chosen); if the DELAY START option has been set, the
countdown to the start of the selected wash cycle will appear.
Pressing the corresponding button allows you to view the maximum spin
speed and temperature values attained by the machine during the set
wash cycle, or the values selected most recently, if these are compatible
with the set wash cycle.
Locked door indicator
When lit, the symbol indicates that the door is locked. To prevent any
damage, wait until the symbol turns off before opening the door.
To open the door while a cycle is in progress, press the START/PAUSE
button
; if the
symbol is off, the door can be opened.
FIRST-TIME USE
Once the appliance has been installed, and before it is used for the first
time, run a wash cycle with detergent and no laundry, by setting the
“Auto-Clean” cycle.
DAILY USE
Prepare the laundry by following the suggestions appearing under the
“TIPS AND SUGGESTIONS” section.
- Press the ON/OFF button ; the indicator light relative to START/PAUSE
will flash slowly.
- Open the door. Load the laundry while making sure not to exceed the
maximum load quantity indicated in the wash cycle table.
- Pull out the detergent dispenser drawer and pour the detergent into the
relevant compartments, as described in the “DETERGENT DISPENSER
DRAWER” section.
- Close the door.
- The machine automatically displays the maximum temperature and spin
speed values for the selected cycle, or the most recently used settings if
they are compatible with the selected cycle. Pressing the button
gradually reduces the temperature down to the cold wash “OFF” setting.
Pressing the button gradually reduces the spin speed until it is
completely excluded (“OFF” setting). Pressing the buttons further restores
the maximum allowed values for the selected cycle.
- Select the desired option.
- Press the START/PAUSE
button to start the wash cycle; the relative
indicator light will light up steady and the door will lock (
symbol on).
PAUSING A CYCLE
To pause the wash cycle, press the START/PAUSE
button again; the
indicator light will flash. To start the wash cycle from the point at which it
was interrupted, press the START/PAUSE
button again.
OPENING THE DOOR, IF NECESSARY
Once a cycle starts, the
symbol turns on to signal that the door cannot
be opened. While a wash cycle is running, the door remains locked. To
open the door while a cycle is under way, for example, to add or remove
garments, press the START/PAUSE
button to pause the cycle; the
indicator light will flash. If the
symbol is not lit, the door may be
opened. Press the START/PAUSE
button again to continue the cycle.
CHANGING A RUNNING WASH CYCLE
To change a wash cycle while it is in progress, pause the washing machine
using the START/PAUSE
button (the relative indicator light will flash),
then select the desired cycle and press the START/PAUSE
button
again.
! To cancel a cycle that has already begun, press and hold the ON/OFF
button. The cycle will be stopped and the machine will switch off.
AT THE END OF THE WASH CYCLE
This will be indicated by the word “END” on the display; when the
symbol switches off, the door may be opened. Open the door, unload the
laundry and switch off the machine. If you do not press ON/OFF
button, the washing machine will switch off automatically after about a
half of an hour.
OPTIONS
- If the selected option is not compatible with the set wash cycle, the
indicator light will flash and the option will not be activated.
Prewash
Allows you to perform a prewash.
Delay start
To set a delayed start for the selected cycle, press the corresponding
button repeatedly until the desired delay period is reached. When this
option has been activated, the
symbol lights up on the display. To
remove the delayed start setting, press the button until “OFF” appears on
the display.
Temperature
Each wash cycle has a pre-defined temperature. To modify the
temperature, press the button. The value will appear on the display.
Spin
Each wash cycle has a pre-defined spin speed. To modify the spin speed,
press the
button. The value will appear on the display.
Cleaning Action
Option
makes it possible to optimise washing based on the level of
soil in the fabrics and on desired wash cycle intensity.
For heavily-soiled garments press
button until the “Intensive”
level is reached. This level ensures a high-performance wash due to a
larger quantity of water used in the initial phase of the cycle and due to
increased drum rotation. It is useful when removing the most stubborn
stains.
For lightly-soiled garments or a more delicate treatment of the fabrics,
press
button until the “Delicate” level is reached. The cycle will reduce
drum rotation to ensure washing results that are perfect for delicate
garments.
CHILD LOCK
To activate the control panel lock, press and hold the
button for
approximately 2 seconds. When the
symbol is lit, the control panel is
locked (except for the ON/OFF button). This will prevent accidental
modifications to wash cycles, especially when children are at home. To
deactivate the control panel lock, press and hold the
button for
approximately 2 seconds.
TIPS AND SUGGESTIONS
Divide the laundry according to:
Type of fabric (cotton, mixed fibres, synthetics, wool, garments to be
hand-washed). Colour (separate coloured garments from whites, wash
new coloured garments separately). Delicates (small garments – such as
nylon stockings – and items with hooks – such as bras: insert them in a
fabric bag).
Empty the pockets:
Objects such as coins or lighters can damage the washing machine and
the drum. Check all buttons.
CARE AND MAINTENANCE
Before performing cleaning and maintenance, switch the washing machine
off and disconnect it from the mains power. Do not use flammable liquids to
clean the washing machine.
Cutting off the water and electricity supplies
Close the water tap after every wash. This will limit wear on the hydraulic
system inside the washing machine and help to prevent leaks.
Unplug the washing machine when cleaning it and during all
maintenance work.
Cleaning the washing machine
The outer parts and rubber components of the appliance can be cleaned
using a soft cloth soaked in lukewarm soapy water. Do not use solvents or
abrasives.
The washing machine has a “Self-Cleaning” cycle for its internal parts; it
must be run without any load in the drum.
To optimise this cycle, it is possible to use either detergent (10% of the
quantity specified for lightly soiled garments) or special additives to clean
the washing machine. We recommend running a cleaning cycle every 40
wash cycles.
To start the programme press button
for 5 seconds.
The cycle will start automatically and will run for about 70 minutes. To
stop the cycle, press the START/PAUSE
button.
Cleaning the detergent dispenser drawer
Remove the dispenser drawer by lifting and pulling it outwards. Wash it
under running water; this procedure should be effected regularly.
Caring for the door and drum
Always leave the porthole door ajar in order to prevent unpleasant
odours from forming.
Cleaning the pump
The washing machine is fitted with a self-cleaning pump that does not
require any maintenance. Small items (such as coins or buttons) may
sometimes fall into the protective pre-chamber situated at the base of the
pump.
! Make sure that the wash cycle has ended and unplug the appliance.
To access the pre-chamber:
1. remove the covering panel on the front side of the machine by
inserting a screwdriver in the centre and sides of the panel and using it as
a lever;
2. loosen the drainage pump cover by turning it anti-clockwise: it is
normal for some water to leak out;
3. clean the inside thoroughly;
4. screw the cover back on;
5. put the panel back in place, making sure the hooks slot in place before
pushing the panel onto the appliance.
Checking the water inlet hose
Check the water inlet hose at least once a year. If it is cracked or broken, it
must be replaced: during wash cycles, the high pressure of the water
could suddenly split the hose open.
! Never use hoses that have already been used.
ACCESSORIES
Contact our Technical Assistance Service to check whether the following
accessories are available for this washing machine model.
Stacking kit
With this accessory you can secure the tumble dryer to the upper part of
your washing machine to save space and facilitate loading and unloading
of the tumble dryer.
TRANSPORT AND HANDLING
Do not lift the washing machine by gripping it from the upper section.
Unplug the appliance and close the water tap. Check that the door and
detergent dispenser drawer are tightly closed. Detach the filling hose
from the water tap then detach the drain hose. Empty all the water
remaining in the hoses and secure the latter so that they do not get
damaged during transport. Apply the transport bolts back on. Repeat, in
reverse order, the transport bolt removal procedure described in the
“Installation instructions”.
TROUBLESHOOTING
Your washing machine could occasionally fail to work. Before contacting the Technical Assistance Service, make sure that the problem cannot be easily
solved using the following list.
Anomalies
Possible causes / Solution
The washing machine does
not start.
The appliance is not plugged into the socket fully, or not enough to make contact.
There is no power in the house.
The washing machine door is not closed properly.
The ON/OFF
button has not been pressed.
The wash cycle does not start. The START/PAUSE
button has not been pressed.
The water tap has not been opened.
A delay has been set for the start time.
The water inlet hose is not connected to the tap.
The hose is bent.
The washing machine does
not fill with water (“H2O”
appears on the display).
The water tap has not been opened.
There is no water supply in the house.
The pressure is too low.
The START/PAUSE
button has not been pressed.
The drain hose is not fitted between 65 and 100 cm from the floor.
The free end of the hose is immersed in water.
The washing machine
continuously loads and
unloads water.
The washing machine does
not drain or spin.
The washing machine
vibrates a lot during the spin
cycle.
The wall drainage system is not fitted with a breather pipe.
If the problem persists even after these checks, turn off the water tap, switch the appliance off and contact the
Technical Assistance Service. If the home is on one of the upper floors of a building, there may be problems relating
to back-siphonage, causing the washing machine to fill with water and drain continuously. Special anti-siphon
valves are available in shops and help to prevent this inconvenience.
The cycle does not include drainage: with certain cycles it must be started manually.
The drain hose is bent.
The drainage duct is clogged.
The drum was not unlocked correctly during installation.
The washing machine is not level.
The washing machine is tucked between furniture cabinets and the wall.
The water inlet hose is not screwed on properly.
The washing machine leaks.
The detergent dispenser drawer is obstructed.
The drain hose is not properly attached.
The “Options” and START/
PAUSE
indicator lights
flash rapidly and the display
visualises an error code (e.g.:
F-01, F-...).
There is too much foam.
Switch off the machine and unplug it, wait for approximately 1 minute and then switch it back on again.
If the problem persists, contact the Technical Assistance Service.
The detergent is not suitable for machine washing (it should display the text “for washing machines” or “hand and
machine wash”, or the like).
Too much detergent was used.
DEMO MODE: to deactivate this function, switch the washing machine OFF. Than press and hold “Start/Pause”
“ON/OFF” button and hold both buttons for 2 seconds.
button, within 5 seconds press also
You can download the SAFETY AND INSTALLATION INSTRUCTIONS, OPERATING MANUAL, TECHNICAL
SHEET and ENERGY DATA by:
• Visiting the website http://docs.bauknecht.eu.
• Using the QR code.
• Alternatively, contact our Technical Assistance Service (the telephone number is indicated in the warranty
booklet). When contacting the Technical Assistance Service, provide the codes shown on the adhesive label applied
to the inside of the door.
xxxx
xxxxxxxxxxxx
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising