Indesit | YT M10 81 R EU | Setup and user guide | Indesit YT M10 81 R EU Setup and user guide

Indesit YT M10 81 R EU Setup and user guide
EN
Quick guide
THANK YOU FOR BUYING A INDESIT PRODUCT.
In order to receive a more complete assistance,
please register your product on
www.indesit.eu/register
Before using the appliance carefully read the Safety Instructions.
CONTROL PANEL
ON/OFF button (Reset if long pressed)
Programme selection knob
Start/Pause button (Start: button lights up
solidly. Pause: button blinks)
4 Push & GO
1
2
3
Options buttons*
5 Dryness level
6 Timed drying
7 Start delay
8 Light drying
9 Crease care (Key lock if long pressed)
10 Cycle end
10
1
9
4
8
DEMO
3’’
2
3
5
6
7
8
*Note: some models may have the wording in full instead of the icons
INDICATORS
Dryness level:
Iron dry Hanger dry - Cupboard dry - Extra dry
Cycle
phase:
Dry
Cool
tumble
- END End of cycle
yer_M10
Empty water tank
Clean door filter
Clean bottom filter
DEMO
Failure: Call after sales service.
Demo mode Refer to troubleshooting section
FIRST TIME USE
Make sure that the water tank is correctly inserted. Make sure
that the drain hose on the back of the dyrer is properly fixed,
either to the dryers's water tank or to the domestic sewage
system.
The dryer should be installed in environment in a room
temperature range of 20°to 23°C for optimum performance. But
will function if the room is between 14 and 30°C. Before you use
your dryer ensure that it has been in a upright position for at
least 6 hours.
DAILY USE
Doing this will keep your machine working at its BEST!
Remember to empty your water tank after each drying cycle.
Remember to clean your filters after each drying cycle. (Refer to
section Care & Maintanence).
start delay
If the door is opened during the cycle, to restart it, close the door and
press the button START/PAUSE. This programme does not allow to set
other options.
OPENING OF THE DOOR DURING THE CYCLE
During operation, it is possible to open the door. After having closed it,
press the button Start/Pause again to restart the dryer.
PROGRAMMES
Eco cotton
kg Max*
Time 215'
Standard cotton programme, suitable to dry normally wet
cotton laundry. Most efficient programme in terms of energy
consumption for drying cotton laundry. The values on the Energy
Label are based on this programme.
Synthetics
kg 4 Time 106'
For drying laundry made of synthetic fibres.
1. Open the door and load garments. Always refer to instructions
Mixed
kg 4 Time 106'
on clothing labels and the max loads indicated in the programme
This programme is ideal for drying cotton and synthetic fabrics
section. Empty pockets. Make sure garments do not get caught
together.
between the door and/or the door filter.
2. Close the door.
Mini synthetics
kg 2 Time 72'
3. Press the button On/Off .
Eco-drying of small laundry loads.
4. Select the programme according to the laundry type.
Mini cotton
kg 2 Time 107'
5. Select the options, if necessary.
Eco-drying of small laundry loads.
6. To start the cycle, press the Start/Pause button.
7. At the end of the drying cycle, a buzzer will beep. An indicator on
Delicates
kg 2 Time 66'
the control panel signals the end of the cycle. Pull the load out
For
drying
delicate
laundry
requiring
a
gentle
treatment.
immediately to prevent the formation of creases on laundry.
8. Turn the machine off by pressing the button On/Off, open the
Wool kg 1 Time 62'
door and pull clothing out. If the machine is not switched off
Programme for drying wool clothing. It is advisable to turn the
manually, after about a quarter of an hour from the cycle end, the
garments inside out before drying. Leave to dry naturally the heaviest
appliance turns off automatically to save energy.
edges that are still damp.
If this last stage is not carried out immediately, some machines
and/or some programmes/options are equipped with Crease Care
system. For some hours, after the end of drying, the drum rotates at
*MAX LOAD 8 Kg (Dry load)
regular intervals to prevent the formation of creases.
In case of power failure, it is necessary to press the button Start/
can download the Safety Instructions, User Manual,CARE
ProductLABEL
Fiche and Energy data by:
xxxx
Pause to restart theYou
cycle.
• Visiting our website - docs.indesit.eu
Always check the care labels, especially when placing garments in
QR Code
PUSH & GO •• Using
the tumble
the firstbooklet).
time. Below
Alternatively, contact our After-sales Service (See phone
numberdryer
in thefor
warranty
When are the most commonly
This function serves to
start a cycle,
after machine
switching
on,the codes
usedprovided
symbols:
contacting
our After-sales
Service,
please state
on your product’s identification plate.
without enabling any further button an/or knob (the programme
May be tumble dried.
PUSH & GO will be deactivated instead).
It is always necessary to follow the points 1, 2, and 3
Do not tumble dry.
concerning the daily use.
Tumble dry – high heat.
To start the cycle Touch & GO, keep the button pressed. The light
on signals that the cycle is started. The cycle is suitable for cotton
Tumble dry – low heat.
and synthetic textiles. Max. load 4 kg. (Cycle duration 140’).
xxxxxxxxxxxx
The duration of these programs will depend on the size of the
load, types of textiles, the spin speed used in your washer and
any extra options selected. In machines equipped with display,
the duration of the cycles is shown on the control panel. The
remaining time is constantly checked and adjusted during the
drying cycle to show the best possible estimate.
Refresh A short programme suitable for refreshing fibres and
garments by means of fresh air. Do not use with garments
that are still wet. It can be used on with any load size but is
more effective with small loads. The cycle duration is about 20
minutes.
Jeans
kg 3 Time 127'
For drying cotton jeans-wear and garments made of robust
cotton, like denim, such as trousers and jackets.
DuvetTime 179'
Programme intended to dry bulky garments, as single duvet.
Baby
kg 2 Time 107'
A programme intended to dry garments and linen of
new-born babies (cotton and chenille), as well as delicate
garments. Do not dry garments having plastic covering.
Shirts
kg 3 Time 137'
This is a programme for Shirts made from cotton or cotton
blend/synthetics.
Sport
kg 4 Time 96'
For drying sports garments made of synthetics or cotton
blends.
Sport shoes
1 pair Time 100'
This programme is intended to dry a pair of sport shoes.
The shoes must be washed and spun at a minimum spin speed
of 400 revolutions. It is necessary to use the apposite shoe rack
supplied. Only dry shoes made of synthetic material or canvas.
Xpress 45'
kg 1 This is a quick timed programme, ideal for drying garments
spun at high speed in the washing machine, e.g. the shirts used
in a working week.
.
45’
OPTIONS
After selecting the programme, the various options can be
set, if necessary.
Dryness level
Press the related button several times to obtain a different
level of residual moisture on garments. An indicator signals the
level being selected.
Iron dry: a very delicate ironing. Suitable for making ironing
of garments easier immediately after the end of the cycle.
Hanger dry: a level intended for delicate garments ready to
be hanged.
Cupboard dry: the garments are ready to be folded and put
away.
Extra dry: used for garments to be worn at the end of the
cycle.
Timed dryning
This option allows to set the drying time. Press the
corresponding button to set the required time for drying. An
indicator on the control panel signals the time being selected.
Start delay
This option allows you to set the delay of the cycle start. Press
the corresponding button several times to obtain the required
delay. After having reached the max. settable time, the option is
reset by pressing the button again. An indicator on the control
panel signals the time being selected. After having pressed the
button Start/Pause, the machine signals the remaining time for the
cycle start. In case of door opening, after closing, it is necessary to
press the button Start/Pause.
Light dry
Enables a more gentle treatment of the laundry by reducing
the drying temperature.
Crease care
This option add a crease treatment at the end of the cycle by
means of a periodic rotation of the drum (duration up to 10 hours).
It is particularly suitable when it is not possible to remove the
laundry as soon as the drying ends. If this option is used together
with the Start Delay, the crease treatment is added also in the
Start Delay phase. This option remains in memory if selected in
the previous drying.
Key lock
This option makes all machine controls inaccesible, except
the button On/Off. When the machine is on:
• to activate the option, keep the button pressed until the
indicator goes on.
• to disable the option, keep the button pressed until the
indicator goes off.
This option remains in memory if selected in the previous drying.
Cycle end
This option activates a prolonged buzzer at the end of the
cycle. Enable it if you are not sure to hear the normal sound at the
end of the cycle. This option remains in memory if selected in the
previous drying.
USE OF SHOE RACK
OPTIONS BUTTONS
These buttons serves to personalise the selected programme
according to personal requirements.
Not all options are available for all programmes. Some options
are incompatible with the ones previously set. The buzzer and/or
blinking indicators will signal the incompatibility. If the option is
available, the option indicator will stay on. Some options may be
kept in the memory of the programme if selected in the previous
drying.
Remove the door filter and place
the shoe rack. Put shoelaces
into the shoes with the shoe tips
facing downwards and the soles
frontwards. Do not add garments
or other shoes into the drum.
Position the door filter back in place
at the end of drying.
EN
Quick guide
THANK YOU FOR BUYING A INDESIT PRODUCT.
In orderMANTENANCE
to receive a more complete assistance,
CARE AND
TRANSPORT AND HANDLING
procedures.
Emptying the water tank after each cycle (see Fig. A).
Pull the container out of the dryer and and empty it into a sink
or other suitable drain, then place it back. Do not use the dryer
without having inserted the container back in place.
Cleaning the door filter after each cycle (see Fig. B).
Pull the filter out and clean it by removing the lint from the filter
surface under running water or using a vacuum cleaner. For optimal
performance, dry up all the filters before inserting them back in
place. Do not use the dryer without having reinserted the filter
in place.
Remove the door filter as described below:
1. Open the door and pull upwards.
2. Open the filter and remove lint from all its parts. Replace it
correctly. Ensure it is completely inserted flush with the dryer seal.
Cleaning the bottom filter when the relevant indicator
turns on (see Fig. C).
Pull the filter out and remove the lint from its surface by washing
it under runing water or by using a vacuum cleaner. However,
it is advisable to clean this filter after each cycle to optimise
drying performance. Do not use the dryer without having
inserted the filter in place first.
Remove the bottom filter as described below:
1. Open the lower door.
2. Take the handle and pull the lower filter out.
3. Open the rear side of the filter and remove the lint from the
inner surface of the mesh.
4. Clean the bottom filter chamber avoiding the direct contact
with the leaves.
5. Close the rear side of the lower filter and place it back by
checking it is perfectly integrated in place.
6. Lower the filter handle and close the bottom door.
7. Make sure the air intake is free.
1. Unplug the dryer.
2. Make sure that door and water tank are properly closed.
3. If the drain hose is connected to your sewage system, fix the
drain hose on the rear of the dryer again (see Installation Guide).
Before
using
carefully
read
the Safety Instructions.
registerduring
your product
on
Unplugplease
the dryer
the cleaning
and maintenance
Never
liftthe
the appliance
dryer by holding
it at the
worktop.
www.indesit.eu/register
Power consumption
off-mode (Po) - Watts
0.50
left-on mode (Pl) - Watts
1.00
Energy consumption Regulation 932/2012.
Programmes
Kg
kWh
Minutes
Eco Cotton*
8
2.58
215
Eco Cotton
4
1.40
127
Synthetics
4
1.18
116
* This is the reference programme for the energy label and suitable
to dry normal wet cotton laundry. This is the most efficient
programme in terms of energy consumption for drying wet cotton
laundry. (Standard/Default starting configuration)
Heat Pump System
The heat pump contains fluorinated greenhouse gases,
contained in a hermetically sealed unit. This sealed unit contains
0.15 kg of the F gas R134a. GWP = 1430 (1 t CO2).
The filters are essential parts for drying. They are intended
to collect the lint formed during drying process. In case
of clogged filters, the air flow inside the dryer would be
seriously affected: the drying times would be longer, the
energy consumption would increase and the dryer could be
damaged. If these procedures are not carried out properly,
the dryer may not start.
PRODUCT DESCRIPTION
1.
2.
3.
4.
Water Tank
Air Intake
Bottom filter
Door filter
A
1
B
C
You can download the Safety Instructions, User Manual, Product Fiche and Energy data by:
• Visiting our website - docs.indesit.eu
• Using QR Code
• Alternatively, contact our After-sales Service (See phone number in the warranty booklet). When
contacting
state the codes provided on your product’s identification plate.
4 our After-sales Service, please
2
3
xxxx
xxxxxxxxxxxx
EN
Quick guide
THANK YOU FOR BUYING A INDESIT PRODUCT.
In order to receive a more complete assistance,
TROUBLESHOOTING
please register your product on
Before using the appliance carefully read the Safety Instructions.
Before contacting
the Service Centre, refer to the table below. Often the malfunctions are minor and can be solved in few minutes
www.indesit.eu/register
Malfunction
The tumble
dryer does not
turn on.
The tumble
dryer does not
start
The drying
times are very
long
Possible cause
The plug is not inserted into the socket.
Solution
Insert the plug into the socket.
The plug is faulty.
Try to plug another appliance in the same socket. Do not use
connecting electrical devices to the socket, as adapters or extensions
A power failure occurred.
Await the reactivation of the power supply.
The door is open.
Close the door.
For machines equipped with this function: await the end of the delay
set or switch the machine off to reset it. Refer to the section Options.
A time delay for the cycle start was set.
The button Start/Pause was not pressed to start Press the button Start/Pause.
the program.
The function Key Lock was enabled (in case of
machines equipped with this option).
Refer to the option section and, if the Key Lock is present, disable it.
Switching the machine off is not enough to disable this option.
An appropriate maintenance was not carried
out.
The programme, the time and/or the drying
level set are not suitable for the type and the
amount of load inserted into the dryer.
Refer to the section Care & Maintenance and perform the operations
described.
The garments are too wet.
Carry out a washing cycle with higher spin speed to remove as much
water as possible.
Refer to the programme section to check the max. load for each
programme.
In case of power failure, it is necessary to press the button Start/Pause
to restart the cycle.
The dryer may be overloaded.
The programme A power failure occurred might have occurred.
did not end.
Lights on or flashing
Refer to the section programmes and options to find the programme
and the options most suitable for the type of load.
Water tank
The water tank is full.
Emtpy the water tank. Refer to the section Care & Maintenance.
Door filter
and/or bottom
filter*
Failure of the air flow necessary for machine
operation.
Clean the door filter and the bottom one and check whether air
intake is free. Carrying out these operations improperly may cause
damages.
Bottom filter*
The bottom filter requires cleaning.
Clean the bottom filter. Refer to section Care & Maintanence.
Disable the DEMO mode. The following actions must be carried out
in sequence, without breaks. Switch the machine on and then switch
it off again. Press the Start/Pause button until the buzzer is heard.
Switch the machine on again. The “DEMO” indicator flashes and then
turns off.
The presence of wrenchSwitch
symbol
signals
malfunction.
out the
the door
operations
described.
the
dryeraoff
and unplugCarry
it. Open
immediately
and
Switch the dryer off andpull
unplug
it. Open
theallow
doorthe
immediately
and pullWait
landry
out, to15
allow
etics
laundry
out,
to
heat
to
dissipate.
for
about
The presence
the heat to dissipate. Wait
for about
one hour.
thepower
dryer supply,
to the power
supply,
load
minutes.
Reconnect
theReconnect
dryer to the
load the
laundry
of wrench
the laundry
and restart and
the drying
a failure.
restart cycle.
the drying cycle. If the problem still occurs, contact
tton symbol signals a The machine sensors detected
Crease
the After-Sales Service Centre and communicate the letters and
malfunction.
Care
digits flashing on the display.
8
etics
For instance: F3 and E2
cate
If the problem still occurs, contact the After-Sales Service Centre and communicate the
Sound
number and the position of the flashing LEDs, starting from the bottom and the left column.
3 sec
DEMO
e.g.:
ans
First, left column, LEDs No. 1 and 3 on.
Central column, LED No. 1 on.
aby
port
tton
DEMO
The cycle lasts
few minutes.
Dryness
level
The dryer is in DEMO mode. The DEMO
indicator is on.
Drying
Time
Start
delay
Memo
*Note: some models are self-cleaning and not equipped with bottom filter. Please refer to the section Care & Maintenance.
You can download the Safety Instructions, User Manual, Product Fiche and Energy data by:
• Visiting our website - docs.indesit.eu
• Using QR Code
• Alternatively, contact our After-sales Service (See phone number in the warranty booklet). When
contacting our After-sales Service, please state the codes provided on your product’s identification plate.
xxxx
xxxxxxxxxxxx
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising