Indesit | BI WMML 71452 UK | Setup and user guide | Indesit BI WMML 71452 UK Setup and user guide

Indesit BI WMML 71452 UK Setup and user guide
Quick Guide
GB
THANK YOU FOR BUYING A INDESIT PRODUCT
In order to receive a more complete assistance,
please register your product on
www.indesit.com/register
Before using the appliance carefully read the Safety Instruction.
Before using the machine, it is imperative that the transport bolts are removed.
For more detailed instructions on how to remove them, see the Installation Guide.
CONTROL PANEL
1
1. ON/OFF button
2. START/PAUSE button with indicator light
3. WASH CYCLE PROGRESS indicator lights
4. DOOR LOCKED indicator light
5. FUNCTION buttons with indicator lights
6. CHILDLOCK button with indicator light
7. DELAY TIMER button
8. SPIN button
9. TEMPERATURE button
10. WASH CYCLE knob
2
3
9
10
WASH CYCLE TABLE
6
Total water l
7
Energy consumption kWh
Recommended
detergent
5
Residual
dampness %
Maximum load 7 kg
Power input in off mode 0,5 W / in left-on mode 8 W
8
4
1
Mix Coloured 59’
40°C
– 40°C
1000
7
59
–


–

–
–
–
2
Cotton 59’
60°C
– 60°C
1000
7
59
–




–
–
–
3
Synthetics 59’
30°C
– 30°C
1000
4
59
–


–

–
–
–
4
Daily 45’
40°C
– 40°C
1200
3,5
45
–


–

–
–
–
5
Mix 30’
30°C
– 30°C
800
3,5
30
–


–

70
0,16
32,4
6
Gym Kit
40°C
– 40°C
600
3,5
90
–


–

–
–
–
7
White
60°C
– 90°C
1400
7
135
+90°




–
–
–
8
Baby
40°C
– 40°C
800
3
85
–


–

–
–
–
Temperature
Wash cycle
Default
Range
Detergents and Additives
Maximum Maximum
Duration Pre-wash
spin
load
(minutes)
(kg)
(r.p.m.)
1
Wash
Fabric
softener
2
3
Powder
Liquid
9
Rinse
–
–
1400
7
50
–
–

–
–
–
–
–
10
Spin + Drain *
–
–
1400
7
10
–
–
–
–
–
–
–
–
11
Duvet
30°C
– 30°C
1000
2
110
–


–

–
–
–
12
Wool
40°C
– 40°C
800
1,5
70
–


–

–
–
–
13
Silk/Curtains
30°C
– 30°C
0
1
55
–


–

–
–
–
14
Eco Cotton 60°/40°(1)
60°C
60°C
1400
7
185
–




53
1,11
52,5
40°C
1400
7
220
–




53
0,97
75
15
Cotton (2)
40°C
– 60°C
1400
7
220
–




53
0,97
75
16
Synthetics (3)
40°C
– 60°C
1000
4
120
–




46
0,67
54,6
 Required dosage
 Optional dosage
The cycle duration indicated on the display or instruction manual is an estimate based on
standard conditions. The actual duration may vary in relation to several factors, such as
the temperature and pressure of the incoming water, ambient temperature, amount of
detergent, load quantity and type, load balancing and any additional options selected.
For all testing institutes:
2) Long cotton cycle: set cycle 15 at a temperature of 40°C.
3) Long synthetics cycle: set cycle 16 at a temperature of 40°C.
1) Test wash cycle in compliance with regulation 1061/2010:
This cycle is designed for normally soiled cotton loads and is the most efficient in terms of
both electricity and water consumption; it should be used for garments washable at 60°C or
at 40°C. The actual washing temperature may differ from the indicated value.
PRODUCT DESCRIPTION
1. Top
2. Detergent dispenser drawer
3. Control panel
4. Handle
5. Porthole door
6. Drain pump
7. Adjustable feet (4)
* By selecting the 10 cycle and excluding the spin cycle, the washing machine will drain only.
DETERGENT DISPENSER DRAWER
1.
2.
3.
4.
5.
6.
7.
Compartment 1: Pre-wash detergent
(powder)
Compartment 2: Washing detergent (powder
or liquid)
Compartment 3: Additives (fabric softener, etc.)
The fabric softener must never exceed the
“max” level indicated on the central pin.
! Use powder detergent for white cotton
garments, for pre-washing, and for washing at
temperatures over 60°C.
! Follow the instructions given on the detergent
packaging.
1
3
2
WASH CYCLES
Follow the instructions on the symbols of the garment’s wash
care label. The value indicated in the symbol is the maximum
recommended temperature for washing the garment.
Mix Coloured 59’
To wash mixed and coloured items together.
Cotton 59’
Cycle designed to wash cotton garments - mainly white items. It can be
used with powder detergent too.
Synthetics 59’
Specific for synthetic items. If the dirt is difficult to remove, the
temperature can be increased up to 60° and powder detergent can be
used too.
Daily 45’
Short cycle designed to wash delicate cotton items.
Mix 30’
For washing lightly soiled garments in a short time. Not suitable for wool,
silk and garments to be washed by hand.
Gym Kit
Cycle suitable to wash all sports items together, including gym towels,
while respecting their fibres (follow the instructions in the garment
labels).
White
For heavily soiled whites and resistant colours.
Baby
Cycle designed for dirt typical of children’s garments in that it effectively
removes any traces of residual detergent.
Rinse
Designed for rinsing and spinning.
Spin + Drain
Designed to spin and drain the water.
Duvet
For washing clothing padded with goose down, such as double or single
duvets (weighing under 2 kg), cushions or down jackets. Duvets should
be loaded into the drum with their edges folded inwards and no more
than ¾ of the total drum volume should be used up. For best results, it is
advisable to use liquid detergent to be poured into the detergent drawer.
Wool
all wool garments can be washed using programme, even those carrying
the “hand-wash only”
label. For best results, use special detergents
and do not exceed 1,5 kg of laundry.
Silk
use special wash cycle to wash all silk garments. We recommend the use
of special detergent which has been designed to wash delicate clothes.
Curtains
fold curtains and place them in a pillow case or mesh bag.
Eco Cotton 60°/40°
Suitable for washing moderately soiled cotton garments. At 40°C and
60°C it is the standard cycle for washing cotton garments, and is the most
efficient in terms of combined water and electricity consumption.
Cotton
Suitable for washing towels, underwear, table cloths, etc. made of
resistant linen and cotton that are moderately to heavily soiled.
Synthetics
Suitable for washing moderately soiled garments made of synthetic fibres
(e.g. polyester, polyacrylic, viscose, etc.) or mixed synthetic-cotton fibres.
WASH CYCLE PHASE INDICATOR LIGHTS
Once the desired wash cycle has been selected and has begun, the
indicator lights switch on one-by-one to indicate which phase of the cycle
is currently in progress.
Wash
Rinse
Spin
Drain
End of Wash Cycle
DOOR LOCKED INDICATOR
When lit, the symbol indicates that the door is locked. To prevent any
damage, wait until the symbol turns off before opening the door.
To open the door while a cycle is in progress, press the START/PAUSE
button; if the indicator light is off, the door can be opened.
FIRST-TIME USE
Once the appliance has been installed, and before it is used for the first
time, run a wash cycle with detergent and no laundry, by setting the
“Auto-Clean” cycle.
DAILY USE
Prepare the laundry by following the suggestions appearing under the
“TIPS AND SUGGESTIONS” section.
- Turn the washing machine on by pressing the ON/OFF button. All the
indicator lights will light up for a few seconds, then only the lights
corresponding to the settings for the selected wash cycle will remain lit;
the START/PAUSE
indicator light will also flash.
- Open the door. Load the laundry while making sure not to exceed the
maximum load quantity indicated in the Wash Cycle Table.
- Pull out the detergent dispenser drawer and pour the detergent into the
relevant compartments as described in “DETERGENT DISPENSER
DRAWER” section.
- Close the door.
- Set the WASH CYCLE knob to the desired cycle.
- Modify the temperature and/or spin: pressing the
button allows
for gradually reducing the temperature down to the cold wash level
(20°C). The spin speed may be progressively reduced by pressing the
button, until it is completely excluded (the “ ” setting. If these buttons
are pressed again, the maximum values are restored.
- Select the desired wash cycle.
- Select the desired options.
- Press the START/PAUSE
button to start the wash cycle; the relative
indicator light will light up steady green and the door will lock ( indicator
light on).
PAUSING A CYCLE
To pause the wash cycle, press the START/PAUSE
button again; the
indicator light will flash. If the indicator light is not lit, the door may be
opened. To start the wash cycle from the point at which it was
interrupted, press the START/PAUSE
button again.
OPENING THE DOOR, IF NECESSARY
Once a cycle starts, the indicator light turns on to signal that the door
cannot be opened. While a wash cycle is running, the door remains
locked. To open the door while a cycle is under way, for example, to add
or remove garments, press the START/PAUSE
button to pause the
cycle; the indicator light will flash. If the indicator light is not lit, the
door may be opened. Press the START/PAUSE
button again to
continue the cycle.
CHANGING A RUNNING WASH CYCLE
To change a wash cycle while it is in progress, pause the washing machine
using the START/PAUSE
button (the relative indicator light will flash),
then select the desired cycle and press the START/PAUSE
button
again.
! To cancel a cycle that has already begun, press and hold the ON/OFF
button.
The cycle will be stopped and the machine will switch off.
END OF THE CYCLE
Once the cycle terminates the
indicator light will light up; when the
indicator light switches off, the door may be opened. Open the door,
unload the laundry and switch off the machine. If you do not press “ON/
OFF” button, the washing machine will switch off automatically after
about a half of an hour. Close the water tap, open the door and unload
the washing machine. Leave the door ajar to allow the drum to dry.
FUNCTIONS
- If the selected option is not compatible with the set wash cycle, the
indicator light will flash and the option will not be activated.
- If the selected option is not compatible with another previously
selected option, the indicator light will flash accompanied by a buzzer,
and only the latter option will be activated; the indicator light
corresponding to the activated option will turn on.
Stain removal
This option allows for selecting the type of dirt so as to optimally adjust the
cycle for removing the stains. The following types of dirt can be selected:
Food: for stains caused by foodstuffs and beverages, for example.
Work: for grease and ink stains, for example.
Outdoor: for mud and grass stains, for example.
! The wash cycle duration varies according to the type of selected dirt.
Extra rinse
By selecting this option, the efficiency of the rinse is increased and
optimal detergent removal is guaranteed. It is particularly useful for
sensitive skin.
Easy iron
By selecting this function, the wash and spin cycles will be modified in
order to limit the formation of creases. At the end of the cycle the
washing machine’s drum will rotate slowly; the EASY IRON and START/
PAUSE
indicator lights will flash and the
phase will remain lit
steady. To end the cycle, press the START/PAUSE
button or the EASY
IRON button.
Delay start
To set a delayed start for the selected cycle, press the corresponding
button repeatedly until the desired delay period has been reached
(3h-6h-9h). When the button is pressed for the fourth time, the option will
deactivate.
Once the START/PAUSE
button has been pressed, the delay time can
only be modified by decreasing it until the set cycle is launched.
Temperature
Each wash cycle has a pre-defined temperature. To modify the
temperature, press the
button.
Spin
Each wash cycle has a pre-defined spin speed. To modify the spin speed,
press the
button.
CHILD LOCK
to activate the control panel lock, press and hold the button for
approximately 2 seconds. The lit
symbol signals that the control
panel is locked. This prevents wash cycles from being modified
accidentally (except for the ON/OFF button), especially if there are
children in the home. To deactivate the control panel lock, press and hold
the button for approximately 2 seconds.
TIPS AND SUGGESTIONS
Divide the laundry according to:
Type of fabric (cotton, mixed fibres, synthetics, wool, garments to be
hand-washed). Colour (separate coloured garments from whites, wash
new coloured garments separately). Delicates (small garments – such as
nylon stockings – and items with hooks – such as bras: insert them in a
fabric bag).
Empty the pockets:
Objects such as coins or lighters can damage the washing machine and
the drum. Check all buttons.
CARE AND MAINTENANCE
Before performing cleaning and maintenance, switch the washing machine
off and disconnect it from the mains power. Do not use flammable liquids to
clean the washing machine.
Disconnect the water and power supplies
Close the water tap after every wash. This will limit wear on the hydraulic
system inside the washing machine and help to prevent leaks.
Unplug the washing machine when cleaning it and during all
maintenance work.
Clean the washing machine
The outer parts and rubber components of the appliance can be cleaned
using a soft cloth soaked in lukewarm soapy water. Do not use solvents or
abrasives.
The washing machine has a “Auto-clean” cycle for its internal parts; it must
be run without any load in the drum.
To optimise this cycle, it is possible to use either detergent (10% of the
quantity specified for lightly soiled garments) or special additives to clean
the washing machine. We recommend running a cleaning cycle every 40
wash cycles.
To start the cycle press buttons
and
simultaneously for 5 seconds.
The cycle will start automatically and will run for about 70 minutes. To
stop the cycle, press the START/PAUSE
button.
Clean the detergent dispenser drawer
Wash it under running water; this operation should be repeated frequently.
Care for the door and drum
Always leave the porthole door ajar in order to prevent unpleasant
odours from forming.
Clean the pump
The washing machine is fitted with a auto-cleaning pump that does not
require any maintenance. Small items (such as coins or buttons) may
sometimes fall into the protective pre-chamber situated at the base of the
pump.
! Make sure the wash cycle has ended and unplug the appliance.
To access the pre-chamber:
1. loosen the drainage pump cover by turning it anti-clockwise: it is
normal for some water to leak out;
2. clean the inside thoroughly;
3. screw the cover back on;
Check the water inlet hose
Check the water inlet hose at least once a year. If it is cracked or broken, it
must be replaced: during wash cycles, the high pressure of the water
could suddenly split the hose open.
! Never use hoses that have already been used.
LOAD BALANCING SYSTEM
Before every spin cycle, to avoid excessive vibrations before every
spin and to distribute the load in a uniform manner, the drum rotates
continuously at a speed which is slightly greater than the washing
rotation speed. If, after several attempts, the load is not balanced
correctly, the machine spins at a reduced spin speed. If the load is
excessively unbalanced, the washing machine performs the distribution
process instead of spinning. To encourage improved load distribution and
balance, we recommend small and large garments are mixed in the load.
TRANSPORT AND HANDLING
Do not lift the washing machine by gripping it from the upper section.
Unplug the appliance and close the water tap. Check that the door and
detergent dispenser drawer are tightly closed. Detach the filling hose
from the water tap then detach the drain hose. Empty all the water
remaining in the hoses and secure the latter so that they do not get
damaged during transport. Apply the transport bolts back on. Repeat, in
reverse order, the transport bolt removal procedure described in the
“Health & Safety and Installation Guides”.
TROUBLESHOOTING
The washing machine may occasionally fail to work. Before contacting the Technical Assistance Service, make sure that the problem cannot be easily
solved using the following list.
Anomalies
Possible causes / Solution
The washing machine does
not start.
The appliance is not plugged into the socket, or not sufficiently to make contact.
There is no power in the house.
The washing machine door is not closed properly.
The ON/OFF
button has not been pressed.
The wash cycle does not start. The START/PAUSE
button has not been pressed.
The water tap has not been opened.
A delay has been set for the start time.
The water inlet hose is not connected to the tap.
The hose is bent.
The machine does not fill with
The water tap has not been opened.
water or the indicator light
for the first wash cycle stage
There is no water supply in the house.
flashes rapidly.
The pressure is too low.
The START/PAUSE
button has not been pressed.
The drain hose is not fitted between 65 and 100 cm from the floor.
The free end of the hose is immersed in water.
The washing machine
continuously loads and
unloads water.
The wall drainage system does not have a breather pipe.
If the problem persists even after these checks, turn off the water tap, switch the appliance off and contact the
Technical Assistance Service. If the home is on one of the upper floors of a building, there may be problems relating
to back-siphonage, causing the washing machine to fill with water and drain continuously. Special anti-siphon
valves are available in shops and help to prevent this inconvenience.
The cycle does not include drainage: with certain cycles it must be started manually.
The washing machine does
not drain or spin.
The drain hose is bent.
The
option is enabled: to complete the wash cycle, press the START/PAUSE
button.
The drainage duct is clogged.
The washing machine
vibrates a lot during the spin
cycle.
The drum was not unlocked correctly during installation.
The washing machine is not level.
The washing machine is tucked between furniture cabinets and the wall.
The water inlet hose is not screwed on properly.
The washing machine leaks.
The detergent dispenser drawer is obstructed.
The drain hose is not properly attached.
The “Options” lights and the
START/PAUSE indicator light
flash while one of the wash
Switch off the machine and unplug it, wait for approximately 1 minute and then switch it back on again.
cycle progress and DOOR
If the problem persists, contact the Technical Assistance Service .
LOCKED lights are lit in a fixed
manner.
There is too much foam.
The detergent is not suitable for machine washing (it should be marked with “for washing machine use” or “hand
wash and machine wash” or similar).
Too much detergent was used.
You can download the Safety Instructions, User Manual, Product Fiche and Energy data by:
• Visiting our website - http://docs.indesit.eu
• Using QR Code
• Alternatively, contact our echnical Assistance Service (See phone number in the warranty booklet). When
contacting our After‑sales Service, please state the codes provided on your product’s identification plate.
xxxxxxxxxxxx
xxxx
11284585
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising