SAFETY INSTRUCTIONS EN IMPORTANT TO BE READ AND OBSERVED Download the complete instruction manual on This appliance is intended to be used in household http://d ocs.w hirlpool.e u or call the phone number and similar applications such as: staff kitchen areas shown on the warranty booklet. in shops, offices and other working environments; farm houses; by clients in hotels, motels, bed & Before using the appliance, read these safety breakfast and other residential environments. instructions. Keep them nearby for future reference. No other use is permitted (e.g. heating rooms). These instructions and the appliance itself provide This appliance is not for professional use. Do not important safety warnings, to be observed at all use the appliance outdoors. times. The manufacturer declines any liability for INSTALLATION failure to observe these safety instructions, for The appliance must be handled and installed by inappropriate use of the appliance or incorrect two or more persons - risk of injury. Use protective setting of controls. gloves to unpack and install - risk of cuts. WARNING: The appliance and its accessible parts Installation, including water supply (if any), become hot during use. Care should be taken to electrical connections and repairs must be carried avoid touching heating elements. out by a qualified technician. Do not repair or replace Children less than 8 years of age shall be kept away any part of the appliance unless specifically stated in unless continuously supervised. the user manual. Keep children away from the WARNING: If the hob surface is cracked, do not installation site. After unpacking the appliance, use the appliance - risk of electric shock. make sure that it has not been damaged during WARNING: Danger of fire: Do not store items on transport. In the event of problems, contact the the cooking surfaces. dealer or your nearest After-sales Service. Once CAUTION: The cooking process has to be installed, packaging waste (plastic, styrofoam parts supervised. A short cooking process has to be etc.) must be stored out of reach of children - risk of supervised continuously. suffocation. The appliance must be disconnected WARNING: Unattended cooking on a hob with from the power supply before any installation fat or oil can be dangerous - risk of fire. NEVER try to operation - risk of electric shock. During installation, extinguish a fire with water: instead, switch off the make sure the appliance does not damage the appliance and then cover flame e.g. with a lid or a power cable - risk of fire or electric shock. Only fire blanket. activate the appliance when the installation has Do not use the hob as a work surface or support. been completed. Keep clothes or other flammable materials away Carry out all cabinet cutting operations before from the appliance, until all the components have fitting the appliance and remove all wood chips and cooled down completely - risk of fire. sawdust. Metallic objects such as knives, forks, spoons and If the appliance is not installed above an oven, a lids should not be placed on the hob surface since separator panel (not included) must be installed in they can get hot. the compartment under the appliance. Very young children (0-3 years) should be kept ELECTRICAL WARNINGS away from the appliance. Young children (3-8 years) It must be possible to disconnect the appliance should be kept away from the appliance unless from the power supply by unplugging it if plug is continuously supervised. Children from 8 years old accessible, or by a multi-pole switch installed and above and persons with reduced physical, upstream of the socket in accordance with the sensory or mental capabilities or lack of experience wiring rules and the appliance must be earthed in and knowledge can use this appliance only if they conformity with national electrical safety standards. are supervised or have been given instructions on Do not use extension leads, multiple sockets or safe use and understand the hazards involved. adapters. The electrical components must not be Children must not play with the appliance. Cleaning accessible to the user after installation. Do not use and user maintenance must not be carried out by the appliance when you are wet or barefoot. Do not children without supervision. operate this appliance if it has a damaged power After use, switch off the hob element by its cable or plug, if it is not working properly, or if it has control and do not rely on the pan detector. been damaged or dropped. PERMITTED USE If the supply cord is damaged, it must be replaced CAUTION: the appliance is not intended to be with an identical one by the manufacturer, its service operated by means of an external switching device, agent or similarly qualified persons in order to avoid such as a timer, or separate remote controlled system. a hazard - risk of electric shock. CLEANING AND MAINTENANCE WARNING: Ensure that the appliance is switched off and disconnected from the power supply before performing any maintenance operation; never use steam cleaning equipment - risk of electric shock. Do not use abrasive or corrosive products, chlorine-based cleaners or pan scourers. DISPOSAL OF PACKAGING MATERIALS The packaging material is 100% recyclable and is marked with the recycle symbol . The various parts of the packaging must therefore be disposed of responsibly and in full compliance with local authority regulations governing waste disposal. DISPOSAL OF HOUSEHOLD APPLIANCES This appliance is manufactured with recyclable or reusable materials. Dispose of it in accordance with local waste disposal regulations. For further information on the treatment, recovery and recycling of household electrical appliances, contact your local authority, the collection service for household waste or the store where you purchased the appliance. This appliance is marked in compliance with European Directive 2012/19/EU, Waste Electrical and Electronic Equipment (WEEE). By ensuring this product is disposed of correctly, you will help prevent negative consequences for the environment and human health. The symbol on the product or on the accompanying documentation indicates that it should not be treated as domestic waste but must be taken to an appropriate collection center for the recycling of electrical and electronic equipment. ENERGY SAVING TIPS Make the most of your hot plate’s residual heat by switching it off a few minutes before you finish cooking. The base of your pot or pan should cover the hot plate completely; a container that is smaller than the hot plate will cause energy to be wasted. Cover your pots and pans with tight-fitting lids while cooking and use as little water as possible. Cooking with the lid off will greatly increase energy consumption. Use only flat-bottomed pots and pans. DECLARATION OF CONFORMITY This appliance meets the Ecodesign requirements set out in European Regulation n. 66/2014, in conformity to the European standard EN 60350‑2. NOTE People with a pacemaker or similar medical device should use care when standing near this induction cooktop while it is on. The electromagnetic field may affect the pacemaker or similar device. Consult your doctor, or the manufacturer of the pacemaker or similar medical device for additional information about its effects with electromagnetic fields of the induction cooktop. EN INSTALLATION 590 mm 4 mm R = Max. 10 mm A 510 mm 50 mm 476 mm 6mm 553 mm R = 11.5 mm Min. 480 mm Max. 492 mm 0 593 + 2 mm 0 560 + 2 mm A 0 513 + 2 mm R = 11.5 mm kit 4801 211 00112 Min. 35 mm 0 560 + 2 mm Min. 480 mm Max. 492 mm R = Max. 10 mm i L Min. 400 mm Min.100 mm 12 mm No Max. Min. 35 mm 28 mm No Max. 90 mm 120 mm 45 mm min. 45 mm min. 10 mm min. 45 mm min. 550 mm 60 mm min. 550 mm min. 20 mm min. 20 mm x4 1 2 x4 2mm 3 90°C 2 1 x4 ELECTRICAL CONNECTION Electrical connection must be made before connecting the appliance to the electricity supply. Installation must be carried out by qualified personnel who know the current safety and installation regulations. Specifically, installation must be carried out in compliance with the regulations of the local electricity supply company. Make sure the voltage specified on the data plate located on the bottom of the appliance is the same as that of the home. Regulations require that the appliance be earthed: use conductors (including the earth conductor) of the appropriate size only. 380-415 V 2 N ~ 220-240 V ~ AU-UK-IRL 220-240 V 3 ~ BE 230V 2 Phase 2N ~ NL 380-415 V 3 N ~ R S 220-240 V ~ black-nero-negro-preto-μαύροσ-must-melns-juodas-czarny-schwarz-noir-zwart-negru-черно-црнčrna-crno-черный-чорний-қара-černá-čierna-fekete-svart-musta-svart-sort-siyah-dubh brown-marrone-marrón-marrom-καφέ-pruun-brūns-rudas-brązowy-braunen-brun-bruin-maro-кaфявбраон-rjava-smeđ-коричневый-коричневий-қоңыр-hnědý-hnedý-barna-brunt-ruskea-brunt-brunkahverengi-donn T blue (gray)-blu (grigio)-azul (gris)-azul (cinza)-μπλε (γκρι)-sinine (hall)-zila (pelēka)-mėlyna (pilkas)niebieski (szary)-blau (grau)-bleu (gris)-blauw (grijs)-albastru (gri)-синьо (сиво)-плава (сива)modro (sivo)-plava (siva)-синий (серый)-синій (сірий)-көк (сұр)-modrý (šedá)-modrý (sivá)kék (szürke)-blå (grå)-sininen (harmaa)-blå (grå)-blåt (gråt)-mavi (gri)-gorm (liath) =E yellow/green-giallo/verde-amarillo/verde-amarelo/verdeκίτρινο/πράσινο-kollane/roheline-dzeltens/zaļšgeltona/žalia-żółty/zielony-gelb/grün-jaune/vert-geel/groen-galben/verde-жълто/зелено-жуто/зеленаrumeno/zeleno-žuto/zelena-желтый/зеленый-жовтий/зелений-жасыл/сары-žlutá/zelená-žltá/zelenásárga/zöld-gul/grønn-keltainen/vihreä-gul/grön-gul/grøn-sarı/yeşil-buí/glas N blue-blu-azul-azul-μπλε-sinine-zila-mėlyna-niebieski-blau-bleu-blauw-albastru-синьо-плава-modroplava-синий-синій-көк-modrý-modrý-kék-blå-sininen-blå-blåt-mavi-gorm EN PRODUCT DESCRIPTION 1. Cooktop 2. Control panel 1 2 CONTROL PANEL 1 5 4 2 3 7 8 11 12 7 3 sec OK 15 10 OFF 18 P OFF 18 P 9 6 7 1. 2. 3. 4. 5. Symbols/activation of special functions Cooking level selected Cooking zone off button Scroll keypad Quick heat button 6. FLEXISIDE button 7. Indicator light – function active 8. On/Off button 9. Timer 10. 6th Sense button OFF 18 P OFF 18 P 14 13 11. Cooking time indicator 12. OK/Key lock button – 3 seconds 13. Timer active indicator 14. Zone selection indicator 15. Timer indicator symbol ACCESSORIES POTS AND PANS Only use pots and pans made from ferromagnetic OK NO material which are suitable for use with induction hobs: • enamelled steel • cast iron • special pots and pans in stainless steel, suitable for induction cooking To determine whether a pot is suitable, check for the symbol (usually stamped on the bottom). A magnet may be used to check whether pots are magnetic. The quality and the structure of the pot base can alter cooking performance. Some indications for the diameter of the base do not correspond to the actual diameter of the ferromagnetic surface. Some pots and pans have only a part of the bottom in ferromagnetic material, with parts in another material that is not suitable for induction cooking. These areas may heat up at different levels or with lower temperatures. In certain cases, where the bottom is made mainly of non-ferromagnetic materials, the hob might not recognise the pan and therefore not switch on the cooking zone. Empty pots or pots with a thin base Do not use empty pots or pans when the hob is on. The hob is equipped with an internal safety system that constantly monitors the temperature, activating the “automatic off“ function where high temperatures are detected. When used with empty pots or pots with thin bases, the temperature may rise very quickly, and the “automatic off“ function may not be triggered immediately, damaging the pan or the hob surface. If this occurs, do not touch anything, and wait for all components to cool down. If any error messages appear, call the service centre. Minimum diameter of pot/pan base for the different cooking areas To ensure that the hob functions properly, the pot must cover one or more of the reference points indicated on the surface of the hob, and must be of a suitable minimum diameter. Always use the cooking zone that best corresponds to the diameter of the bottom of the pan. 100 mm To ensure optimum efficiency, always use pots and pans with a flat bottom that distributes the heat evenly. If the bottom is uneven, this will affect power and heat conduction. 150 mm 150 mm 200 mm ADAPTER FOR POTS/PANS UNSUITABLE FOR INDUCTION Using this accessory makes it possible to use pots and pans that are not suitable for induction hobs. It is important to bear in mind that using it affects efficiency and consequently the time needed to heat food. Its use should be limited because the temperatures reached on its surface depend significantly on the pot/pan used, its flatness and the type of food being cooked. Using a pot or pan with a smaller diameter than the adapter disc may cause heat to build up that is not transmitted to the pot or pan and this could blacken both the hob and the disc. Adapt the diameter of your pots/pans and the hob to the diameter of the adapter. FIRST TIME USE POWER MANAGEMENT At the time of purchase, the hob is set to the maximum possible power. Adjust the setting in relation to the limits of the electrical system in your home as described in the following paragraph. If an error occurs during the setting sequence, the symbol will appear, and you will hear a beep. If this happens, repeat the operation. If the error persists, contact the After-Sales Service. To set the power of the hob: Once you have connected the device to the mains power supply, you can set the power level within 60 seconds. Press the far right timer “+“ button for at least 5 seconds. The display shows ACOUSTIC SIGNAL ON / OFF To switch the acoustic signal on/off: • Switch on the hob. • Press the “P“ button of the first scroll keypad at the top left for 5 seconds. Any alarms set will remain active. . Press the button until the last power level selected appears. Use the “+“ and “−“ buttons to select the desired power level. The power levels available are: 2.5 kW – 4.0 kW – 6.0 kW – 7.2 kW. Confirm by pressing . 3 sec OK 3 sec OK The power level selected will stay in the memory even if the power supply is interrupted. To change the power level, disconnect the appliance from the mains for at least 60 seconds, then plug it back in and repeat the steps above. DEMO MODE To switch the demo mode on and off: • Connect the hob to the power supply; • Within the first minute, press the quick heating button “P“ of the bottom left keypad for 5 seconds (as shown below). OFF 18 P OFF 18 P 3 sec OK OFF 18 P OFF 18 P EN DAILY USE SWITCHING THE HOB ON/OFF To turn the hob on, press the power button for around 1 second. To turn the hob off, press the same button again, and all cooking zones will be deactivated. POSITIONING Do not cover the control panel symbols with the cooking pot. Please note: In the cooking zones close to the control panel, it is advisable to keep pots and pans inside the markings (taking both the bottom of the pan and the upper edge into consideration, as this tends to be larger). This prevents excessive overheating of the keypad. When grilling or frying, please use the rear cooking zones wherever possible. ACTIVATING/DEACTIVATING COOKING ZONES AND ADJUSTING POWER LEVELS 18 OFF P To activate the cooking zones: Move your finger horizontally across the scroll keypad (SLIDER) of the required cooking zone to activate it and adjust the power. The level will be shown in line with the area, along with the indicator light identifying the active cooking zone. The “P“ button can be used to select the quick heating function. To deactivate the cooking zones: Select the “OFF“ button at the beginning of the scroll keypad. OK CONTROL PANEL LOCK To lock the settings and prevent it being switched on accidentally, press and hold the OK/Key lock button for 3 seconds. A beep and a warning light above the symbol indicate that this function has been activated. The control panel is locked except for the switching off function( ). To unlock the controls, repeat the activation procedure. 3 sec TIMER There are two timers - one controls the left-hand cooking zones, while the other controls the right-hand cooking zones. To activate the timer: Press the “+“ or “−“ button to set the desired time on the cooking zone in use. An indicator light will be activated in line with the specific symbol . Once the set time has elapsed, a beep will sound, and the cooking zone will switch off automatically. The time can be changed at any point, and several timers can be activated simultaneously. In case 2 timers on the same side of the hob are activated simultaneously, “Zone selection indicator“ flashes and the relative cooking time selected is displayed on the central display. To deactivate the timer: Press the “+“ and “−“ buttons together until the timer is deactivated. TIMER INDICATOR This LED (when ON) indicates that the timer has been set for the cooking zone. FUNCTIONS OFF 18 P OFF 18 P FLEXISIDE By selecting the “FLEXISIDE“ button, you can combine two cooking zones and use them at the same power by covering the entire surface with a large pot or partially with a round/oval pot. The function always remains on and, when using only one pot, can be moved over the entire area. In this case, both left-hand scroll keypads can be used indifferently. Ideal for cooking with oval or rectangular pots or with pan supports. 6TH SENSE The “6 Sense“ button activates the special functions. Place the pot in position and select the cooking zone. Press the “6th Sense“ button. “A“ will appear on the display. The indicator for the first special feature available for the cooking zone will light up. Select the desired special function by pressing the “6th Sense“ button one or more times. The function is activated once the button has been pressed to confirm. If you want to change the special function press the “OFF“ button and then the “6th Sense“ button to select the desired function. To deactivate the special functions, press and hold down the “OFF“ button. th 3 sec OK 3 sec OFF 18 P OFF 18 P MELTING This function allows you to bring food to the ideal temperature for melting and to maintain the condition of the food without risk of burning. This method is ideal, as it does not damage delicate foods such as chocolate, and prevents them from sticking to the pot. KEEP WARM This feature allows you to keep your food at an ideal temperature, usually after cooking is complete, or when reducing liquids very slowly. Ideal for serving foods at the perfect temperature. SIMMERING This function is ideal for maintaining a simmering temperature, allowing you to cook food for long periods with no risk of burning. Ideal for longcooking recipes (rice, sauces, roasts) with liquid sauces. BOILING This function allows you to bring water to the boil and keep it boiling, with lower energy consumption. About 2 litres of water (preferably at room temperature) should be placed in the pan, and left uncovered. In all cases, users are advised to monitor the boiling water closely, and check the amount of water remaining regularly. CHEF CONTROL The flexible zone is divided into three cooking (see the figure) activated at a pre-set power high zones (high, medium or low) depending on the position of the pot/pan: move the pot/pan over the surface medium to continue cooking at different temperatures without having to use the controls. low INDICATORS POT INCORRECTLY POSITIONED OR MISSING This symbol appears if the pot is not suitable for induction cooking, is not positioned correctly or is not of an appropriate size for the cooking zone selected. If no pot is detected within 30 seconds of making the selection, the cooking zone switches off. RESIDUAL HEAT If the display shows “H“, the cooking zone is still hot. When the cooking zone cools down, the display goes off. COOKING TABLE POWER LEVEL Maximum power P 14 − 18 10 − 14 5−9 TYPE OF COOKING LEVEL USE (indicating cooking experience and habits) Fast heating Ideal for rapidly increasing the temperature of food to a fast boil (for water) or for rapidly heating cooking liquids. Frying − boiling Ideal for browning, starting to cook, frying deep-frozen products, bringing liquids to the boil quickly. Browning − sautéing − boiling − grilling Browning − cooking − stewing − sautéing − grilling Ideal for sautéing, maintaining a gentle boil, cooking and grilling, and preheating accessories. Cooking − stewing − sautéing − grilling − cooking until creamy Ideal for stewing, maintaining a gentle boil, cooking and grilling (for longer periods). Cooking − simmering − thickening − creaming Melting − defrosting Zero power Ideal for sautéing, maintaining a lively boil, cooking and grilling. Ideal for slower-cook recipes (rice,sauces,roast,fish) with liquids (e.g. water, wine, broth, milk), and for creaming pasta. Ideal for slow-cook recipes (quantities under 1 litre: rice, sauces, roasts, fish) with liquids (e.g. water,wine,broth,milk). Ideal for softening butter, gently melting chocolate, thawing small items. 1−4 Keeping food warm − creaming risotto Ideal for keeping small portions of just-cooked food or serving dishes warm and for creaming risotto. OFF – Hob in stand-by or off mode (possible end-of-cooking residual heat, indicated by an “H“). EN MAINTENANCE AND CLEANING ! WARNING • Do not use steam cleaning equipment. • Before cleaning, make sure the cooking zones are switched off and that the residual heat indicator (“H“) is not displayed. Important: • Do not use abrasive sponges or scouring pads as they may damage the glass. • After each use, clean the hob (when it is cool) to remove any deposits and stains from food residue. • A surface that is not kept suitably clean may reduce the sensitivity of control panel buttons. • Use a scraper only if residues are stuck to the hob. Follow the scraper manufacturer's instructions to avoid scratching the glass. • Sugar or foods with a high sugar content can damage the hob and must be immediately removed. • Salt, sugar and sand could scratch the glass surface. • Use a soft cloth, absorbent kitchen paper or a special hob cleaner (follow the Manufacturer’s instructions). • Spills of liquid in the cooking zones can cause the pots to move or vibrate. • After cleaning the hob, dry thoroughly. If the iXelium™ logo appears on the glass, the hob has been treated with iXelium™ technology, an exclusive Whirlpool finish which ensures perfect cleaning results, as well as keeping the surface of the hob shiny for longer. To clean iXelium™ hobs, follow these recommendations: • Use a soft cloth (microfibre is best) dampened with water or with everyday glass cleaning detergent. • For best results, leave a wet cloth on the glass hob surface for a few minutes. TROUBLESHOOTING • • • Check that the electricity supply has not been shut off. If you are unable to turn the hob off after using it, disconnect it from the power supply. If alphanumeric codes appear on the display when the hob is switched on, consult the following table for instructions. DISPLAY CODE F0E1 F0E7 DESCRIPTION Please note: The presence of water, liquid spilled from pots or any objects resting on any of the hob buttons can accidentally activate or deactivate the control panel lock function. POSSIBLE CAUSES SOLUTION Cookware is detected but it is not compatible with requested operation. The cookware is not well positioned on Press On/Off button twice to remove the the cooking zone, or it is not compatible F0E1 code and restore the functionality of the with one or more cooking zones. cooking zone. Then, try to use the cookware with a different cooking zone, or use different cookware. Wrong power cord connection. The power supply connection is not Adjust the power supply connection exactly as indicated in “ELECTRICAL according to “ELECTRICAL CONNECTION“ CONNECTION“ paragraph. paragraph. F0EA The control panel switches off because The internal temperature of electronic Wait for the hob to cool down before using of excessively high temperatures. parts is too high. it again. F0E2, F0E4, F0E6, F0E8, F0EC, F1E1, F6E1, F7E5, F7E6 Disconnect the hob from the power supply. Wait a few seconds then reconnect the hob to the power supply. If the problem persists, call the service centre and specify the error code that appears on the display. dE [when the hob is off] The hob does not switch heat up. The functions do not come on. DEMO MODE on. Follow the instructions in the “DEMO MODE“ paragraph. SOUNDS PRODUCED DURING OPERATION Induction hobs may whistle or creak during normal operation. These noises actually come from the cookware and are linked to the characteristics of the pan bottoms (for example, when the bottoms are made from different layers of material or are irregular). These noises may vary according to the type of cookware used and to the amount of food it contains and are not the symptom of something wrong. AFTER-SALES SERVICE In order to receive a more complete assistance, please register your product on www.whirlpool.eu/register. • the service number (number after the word Service on the rating plate). The service number is also indicated on the guarantee booklet; • • your full address; your telephone number. BEFORE CALLING THE AFTER-SALES SERVICE: 1. See if you can solve the problem by yourself with the help of the suggestions given in the TROUBLESHOOTING. 2. Switch the appliance off and back on again to see if the fault persists. IF AFTER THE ABOVE CHECKS THE FAULT STILL OCCURS, GET IN TOUCH WITH THE NEAREST AFTER-SALES SERVICE. To receive assistance, call the number shown on the warranty booklet or follow the instructions on the website www.whirlpool.eu. When contacting our Client After sales service, always specify: • a brief description of the fault; • the type and exact model of the appliance; Type: XXX Mod.: XXX XXXXXXXXXXXXXXXXXXXX Made in X XXXXXXXXXXXXXXX XXXXXXXXXXXXXXXXXXXXXX 400011362925 01 XXXX XXX XXXXX XXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXXX XX XXXX XXXXX If any repairs are required, please contact an authorized after-sales service (to guarantee that original spare parts will be used and repairs carried out correctly). In the case of flush-mounted installation, call the After Sales Service to request assembly of screws kit 4801 211 00112.
* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project