Whirlpool | AWD716W TW | Setup and user guide | Whirlpool AWD716W TW Setup and user guide

Whirlpool AWD716W TW Setup and user guide
User Manual
www.aristonbrand.com
Quick Guide
GB
THANK YOU FOR PURCHASING A ARISTON PRODUCT.
Before using the appliance carefully read the Safety Instruction.
Before using the machine, it is imperative that the transport bolts are removed.
For more detailed instructions on how to remove them, see the Installation Guide.
To receive more comprehensive assistance, register the
appliance on
www.aristonchannel.com/register
CONTROL PANEL
1
ON/OFF button
TEMPERATURE button
OPTION buttons and indicator lights
START/PAUSE button and indicator light
DRYING button
SPIN button
WASH CYCLE SELECTOR KNOB
Detergent dispenser drawer
DISPLAY Дисплей
8
WASH CYCLE TABLE
7
Maximum load 7 kg
Power input in off mode 0.5 W / in left-on mode 8 W
Default
Range
Maximum Maximum Duration
spin
load
(minutes)
(r.p.m.)
(kg)
1
Mix Coloured 59’
40°C
– 40°C
1000
7
2
Synthetics 59’
30°C
– 30°C
1000
3,5
3
Daily 45’
40°C
– 40°C
1200
3,5
4
Wash&Dry 90’
30°C
– 30°C
1200
2
5
Wash&Dry 45’
30°C
– 30°C
1600
1
6
Cotton (2)
40°C
– 60°C
1600
7
7
Synthetics
40°C
– 60°C
1000
3
8
Wool
40°C
– 40°C
800
2
9
Kit Gym
40°C
– 40°C
600
3,5
10
Eco Cotton 60°/40° (1)
60°C
– 60°C
1600
7
11
White
60°C
– 90°C
1600
7
12
Rinse
–
–
1600
7
13
Spin
–
–
1600
7
14
Drain
–
–
–
7
15
Dry Cotton
–
–
–
5
16
Dry Synthetics
–
–
–
3
The duration of the wash cycles can be checked on the display.
Temperature
Wash cycle
 Required dosage
4
3
2
6
Drying
1.
2.
3.
4.
5.
6.
7.
8.
5
Detergents and
Additives
Fabric
Wash
softener
2
3
Recommended
detergent
Powder Liquid



–




–




–





–



–









–




–




–












–

–
–

–
–
–
–
–
–
–
–
–

–
–
–
–

–
–
–
–
 Optional dosage
The cycle duration indicated on the display or instruction manual is an estimate based on
standard conditions. The actual duration may vary in relation to several factors, such as
the temperature and pressure of the incoming water, ambient temperature, amount of
detergent, load quantity and type, load balancing and any additional options selected.
Test wash cycle in compliance with regulation EN 50229 (Wash):
1) Set wash cycle 10 with a temperature of 60°C.
For all testing institutes:
2) Long cotton cycle: set cycle 6 at a temperature of 40°C.
DETERGENT DISPENSER DRAWER
Test wash cycle in compliance with regulation EN 50229 (Drying):
Select the “Dry Cotton” programme and set the drying level to “A4”, for both loads. The first
drying cycle must be carried out with the nominal load.
PRODUCT DESCRIPTION
1. Top
2. Detergent dispenser drawer
3. Control panel
4. Handle
5. Porthole door
6. Drain pump (behind the plinth)
7. Plinth (removable)
8. Adjustable feet (2)
1.
2.
3.
4.
5.
6.
7.
8.
Compartment 1: Do not pour detergent into the
compartment 1.
Detergent should only be poured into the
compartment 2.
Compartment 2: Washing detergent (powder
3
or liquid)
2
1
Liquid detergent should only be poured in
immediately prior to the start of the wash cycle.
Compartment 3: Additives (fabric softener,
etc.)
The fabric softener should not overflow the grid.
Note: If a “tablet detergent” is used, always follow the manufacturer’s
instructions.
! Use powder detergent for white cotton garments, for pre-washing, and
for washing at temperatures over 60°C.
! Follow the instructions given on the detergent packaging.
WASH CYCLES
Follow the instructions on the symbols of the garment’s wash
care label. The value indicated in the symbol is the maximum
recommended temperature for washing the garment.
Mix Coloured 59’
to wash mixed and coloured items together.
Synthetics 59’
Suitable for washing moderately soiled garments made of synthetic fibres
(e.g. polyester, polyacrylic, viscose, etc.) or mixed synthetic-cotton fibres.
Daily 45’
short cycle designed to wash delicate cotton items.
Wash&Dry 90’
he cycle guarantees the washing and drying performances for a 2 kg load
in 90 minutes (level “A1” Iron dry); for larger loads, the cycle’s duration
increases in order to guarantee the cycle performances.
Wash&Dry 45’
select programme 5 for washing and drying lightly soiled garments
(Cotton and Synthetic) in a short time. This cycle may be used to wash
and dry a laundry load of up to 1 kg in just 45 minutes (level “A1” Iron dry).
To achieve optimum results, use liquid detergent and pre-treat cuffs,
collars and stains.
Cotton
suitable for washing towels, underwear, table cloths, etc. made of
resistant linen and cotton that are moderately to heavily soiled.
Synthetics
specific for synthetic items. If the dirt is difficult to remove, the
temperature can be increased up to 60° and powder detergent can be
used too.
Wool
all wool garments can be washed using programme 8, even those
carrying the “hand-wash only”
label. For best results, use special
detergents and do not exceed 2 kg of laundry.
Kit Gym
cycle suitable to wash all sports items together, including gym towels, while
respecting their fibres (follow the instructions in the garment labels).
Eco Cotton 60°/40°
Suitable for washing moderately soiled cotton garments. At 40°C and
60°C it is the standard cycle for washing cotton garments, and is the most
efficient in terms of combined water and electricity consumption.
White
extremely soiled whites.
Rinse
designed for rinsing and spinning.
Spin
designed to spin and drain the water.
Drain
designed for draining the water.
Dry Cotton
designed for drying cotton fabrics.
Dry Synthetics
designed for drying Synthetics fabrics.
DISPLAY
The display is useful when programming the machine and provides a
great deal of information.
B
The icons corresponding to “temperature” , “Drying”
and “spin”
appear in section C from top to bottom:
If the symbol lights up, the display will visualise the set “temperature”
value.
The
symbol lights up while the drying settings are being adjusted.
If the
symbol lights up, the display will visualise the set “spin” value.
DOOR LOCKED INDICATOR
When lit, the symbol indicates that the door is locked. To prevent any
damage, wait until the symbol turns off before opening the door (wait
approximately 3 minutes).
To open the door while a cycle is in progress, press the START/PAUSE
button ; if the symbol is off, the door can be opened (wait
approximately 3 minutes).
FIRST-TIME USE
Once the appliance has been installed, and before it is used for the first
time, run a wash cycle with detergent and no laundry, by setting the “Auto
Clean” cycle.
DAILY USE
Prepare the laundry by following the suggestions appearing under the
“TIPS AND SUGGESTIONS” section.
- Press the ON/OFF button ; the START/PAUSE indicator light will
flash slowly green.
- Open the door. Load the laundry while making sure not to exceed the
maximum load quantity indicated in the Wash Cycle Table.
- Pull out the detergent dispenser drawer and pour the detergent into the
relevant compartments as described in “DETERGENT DISPENSER DRAWER”
section.
- Close the door.
- Select the desired wash cycle.
- Set the washing temperature.
- Set the drying cycle if necessary.
- Select the desired options.
- Press the START/PAUSE button to start the wash cycle; the relative
indicator light will light up steady green and the door will lock ( symbol on).
PAUSING A CYCLE
To pause the wash cycle, press the START/PAUSE button again; the
indicator light will flash amber. If the symbol is not lit, the door may be
opened (wait approximately 3 minutes). To start the wash cycle from the
point at which it was interrupted, press the START/PAUSE button again.
OPENING THE DOOR, IF NECESSARY
Once a cycle starts, the symbol turns on to signal that the door cannot
be opened. While a wash cycle is running, the door remains locked. To
open the door while a cycle is under way, for example, to add or remove
garments, press the START/PAUSE button to pause the cycle; the
indicator light will flash amber. If the symbol is not lit, the door may be
opened (wait approximately 3 minutes). Press the START/PAUSE button
again to continue the cycle.
CHANGING A RUNNING WASH CYCLE
To change a wash cycle while it is in progress, pause the washer-dryer
using the START/PAUSE
button (the relative indicator light will flash
amber), then select the desired cycle and press the START/PAUSE
button again.
! To cancel a cycle that has already begun, press and hold the ON/OFF
button. The cycle will be stopped and the machine will switch off.
END OF THE CYCLE
Once the cycle terminates the END indicator light will light up; when the
symbol switches off, the door may be opened (wait approximately 3
minutes). Open the door, unload the laundry and switch off the machine. If
you do not press ON/OFF button, the washer-dryer will switch off
automatically after about a half of an hour. Close the water tap, open the
door and unload the washer-dryer. Leave the door ajar to allow the drum to
dry.
A
C
The duration of the available programmes and the remaining time of a
running cycle appear in section A; if the DELAY TIMER option has been
set, the countdown to the start of the selected programme will appear.
Furthermore, pressing the corresponding button allows you to view the
maximum temperature, spin speed and drying level or time values
attained by the machine during the selected cycle.
The phases scheduled for the selected cycle and, once the cycle has
begun, the current phase of the wash cycle (and drying cycle, if
applicable) appear in section B.
Wash
Rinse
Spin / Drain
Drying
OPTIONS
- If the selected option is not compatible with the programmed wash
cycle, the indicator light will flash and the option will not be activated.
- If the selected option is not compatible with another option which
has been selected previously, the indicator light corresponding to the
first option selected will flash and only the second option will be
activated; the indicator light corresponding to the enabled option will
remain lit.
Extra Wash
Enable the Extra Wash option for very dirty items, where compatible.
Press this option to let the cycle automatically re-adjust all wash
parameters through a longer lasting cycle. The option always leaves the
temperature unchanged, while the spin cycle is automatically brought
back to maximum levels. The user can set the spin cycle back to the
desired value at any time.
Easy Iron
By selecting this function, the wash and spin cycles will be modified in
order to reduce the formation of creases. At the end of the cycle the
washing machine will perform slow rotations of the drum; the indicator
lights for the EASY IRON and START/PAUSE options will flash (the first one
green, the second orange).
To end the cycle, press the START/PAUSE button or the EASY IRON button.
Note: If you also want to run the drying cycle, this option is enabled only
if combined with level “A1”(Iron dry).
Extra rinse
By selecting this option, the efficiency of the rinse is increased and
optimal detergent removal is guaranteed. It is particularly useful for
sensitive skin.
Delay timer
To set a delayed start for the selected cycle, press the corresponding
button repeatedly until the required delay period has been reached.
When this option is enabled, the corresponding indicator light will remain
lit. To remove the delayed start setting, press the button until the text
“OFF” appears on the display.
Temperature
Each wash cycle has a pre-defined temperature. To modify the
temperature, press the button. The value will appear on the display.
Spin
Each wash cycle has a pre-defined spin speed. To modify the spin speed,
press the
button. The value will appear on the display.
Drying cycle
The first time the button is pressed, the machine will automatically select
the maximum drying cycle which is compatible with the selected wash
cycle. Subsequent presses will decrease the drying level and then the
drying time, until the cycle is excluded completely (“OFF”).
Drying may be set as follows:
A - Based on the desired laundry dryness level:
Iron dry “A1”: suitable for clothes which will need ironing afterwards. the
remaining dampness softens creases,
making them easier to remove.
Hanger dry “A2”: ideal for clothes which do not need to be dried fully.
Cupboard dry “A3”: suitable for laundry which can be put back in a
cupboard without being ironed.
Extra dry “A4”: suitable for laundry which can be put back in a cupboard
without being ironed.
B - Based on a set time period: between 30 and 180 minutes.
If your laundry load to be washed and dried is much greater than the
maximum stated load (see Wash Cycle Table), perform the wash cycle, and
when the cycle is complete, divide the garments into groups and put
some of them back in the drum.
At this point, follow the instructions provided for a Drying only cycle.
Repeat this procedure for the remainder of the load.
N.B: a cooling-down period is always added to the end of each drying cycle.
Drying only
Use the cycle selector knob to select a drying cycle (15-16) in accordance
with the type of fabric. The desired drying level or time may also be set
using the DRYING button
.
TIPS AND SUGGESTIONS
Divide the laundry according to:
Type of fabric (cotton, mixed fibres, synthetics, wool, garments to be
hand-washed). Colour (separate coloured garments from whites, wash
new coloured garments separately). Delicates (small garments – such as
nylon stockings – and items with hooks – such as bras: insert them in a
fabric bag).
Empty the pockets:
Objects such as coins or lighters can damage the washer-dryer and the
drum. Check all buttons.
CARE AND MAINTENANCE
Before performing cleaning and maintenance, switch the washer-dryer off
and disconnect it from the mains power. Do not use flammable liquids to
clean the washer-dryer.
Disconnect the water and power supplies
Close the water tap after every wash. This will limit wear on the hydraulic
system inside the washer-dryer and help to prevent leaks.
Unplug the washer-dryer when cleaning it and during all maintenance
work.
Clean the washer-dryer
The outer parts and rubber components of the appliance can be cleaned
using a soft cloth soaked in lukewarm soapy water. Do not use solvents or
abrasives.
The washer-dryer has a “Auto Clean” programme for its internal parts that
must be run with no load in the drum.
For maximum performance you may want to use either the detergent (i.e.
a quantity 10% the quantity specified for lightly-soiled garments) or
special additives to clean the washer-dryer. We recommend running a
cleaning programme every 40 wash cycles.
To start the programme press buttons
and
simultaneously for 5
seconds.
The programme will start automatically and will last approximately 70
minutes.
Care for the door and drum
Always leave the porthole door ajar in order to prevent unpleasant odours
from forming.
LOAD BALANCING SYSTEM
Before every spin cycle, to avoid excessive vibrations before every
spin and to distribute the load in a uniform manner, the drum rotates
continuously at a speed which is slightly greater than the washing
rotation speed. If, after several attempts, the load is not balanced
correctly, the machine spins at a reduced spin speed. If the load is
excessively unbalanced, the washer-dryer performs the distribution
process instead of spinning. To encourage improved load distribution and
balance, we recommend small and large garments are mixed in the load.
ACCESSORIES
Contact our Technical Assistance Service to check whether the following
accessories are available for this washer-dryer model.
Stacking kit
With this accessory you can secure the tumble dryer to the upper part of
your washer-dryer to save space and facilitate loading and unloading of
the tumble dryer.
TRANSPORT AND HANDLING
Do not lift the washer-dryer by gripping it from the upper section.
Unplug the appliance and close the water tap. Check that the door and
detergent dispenser drawer are tightly closed. Detach the filling hose
from the water tap then detach the drain hose. Empty all the water
remaining in the hoses and secure the latter so that they do not get
damaged during transport. Apply the transport bolts back on. Repeat, in
reverse order, the transport bolt removal procedure described in the
“Health & Safety and Installation Guides”.
TROUBLESHOOTING
The washer-dryer may occasionally fail to work. Before contacting the Technical Assistance Service, make sure that the problem cannot be easily solved
using the following list.
Anomalies
Possible causes / Solution
The washer-dryer does not
start.
The appliance is not plugged into the socket, or not sufficiently to make contact.
There is no power in the house.
The washer-dryer door is not closed properly.
The ON/OFF
The wash cycle does not start.
button has not been pressed.
The START/PAUSE
button has not been pressed.
The water tap has not been opened.
A delay has been set for the start time.
DRYING is in the OFF position.
The water inlet hose is not connected to the tap.
The hose is bent.
The washing machine does
not fill with water (“H2O”
flashes on the display).
The water tap has not been opened.
There is no water supply in the house.
The pressure is too low.
The START/PAUSE
button has not been pressed.
The drain hose is not fitted between 65 and 100 cm from the floor.
The free end of the hose is immersed in water.
The washer-dryer
continuously loads and
unloads water.
The washer-dryer does not
drain or spin.
The washer-dryer vibrates a
lot during the spin cycle.
The wall drainage system does not have a breather pipe.
If the problem persists even after these checks, turn off the water tap, switch the appliance off and contact the
Technical Assistance Service. If the home is on one of the upper floors of a building, there may be problems relating
to back-siphonage, causing the washer-dryer to fill with water and drain continuously. Special anti-siphon valves
are available in shops and help to prevent this inconvenience.
The cycle does not include drainage: with certain cycles it must be started manually.
The drain hose is bent.
The drainage duct is clogged.
The drum was not unlocked correctly during installation.
The washer-dryer is not level.
The washer-dryer is tucked between furniture cabinets and the wall.
The water inlet hose is not screwed on properly.
The washer-dryer leaks.
The detergent dispenser drawer is obstructed.
The drain hose is not properly attached.
The “Option” indicator lights
and the START/PAUSE
indicator light flash and an
error code appears on the
display (e.g.: F-01, F-..).
There is too much foam.
Switch off the machine and unplug it, wait for approximately 1 minute and then switch it back on again.
If the problem persists, contact the Technical Assistance Service .
The detergent is not suitable for machine washing (it should be marked with “for washing machine use” or “hand
wash and machine wash” or similar).
Too much detergent was used.
CLEANING & MAINTENANCE
For any cleaning and maintenance, switch off and unplug the washing machine.
Do not use flammable fluids to clean the washing machine.
CLEANING THE OUTSIDE OF THE WASHING MACHINE
Use a soft damp cloth to clean the outer parts of the washing
machine.
Do not use glass or general purpose cleaners, scouring
powder or similar to clean the control panel – these
substances might damage the printing.
CHECKING THE WATER SUPPLY HOSE
Check the inlet hose regularly for brittleness and cracks. If
damaged, replace it by a new hose available through our
After-Sales Service or your specialist dealer.
Depending on the hose type:
If the inlet hose has a transparent coating, periodically check
if the colour intensifies locally. If yes, the hose may have a leak
and should be replaced.
For water stop hoses: check the small safety valve inspection
window (see arrow). If it is red, the water stop function was
triggered, and the hose must be replaced by a new one.
For unscrewing this hose, press the release button (if
available) while unscrewing the hose.
CLEANING THE MESH FILTERS IN THE WATER SUPPLY HOSE
1. Close water tap and unscrew the inlet hose.
1
3. Now unscrew the inlet hose on the back of the washing
machine by hand. Pull out the mesh filter from the valve
on the back of the washing machine with pliers and
carefully clean it.
2
2. Clean the mesh filter at the hose’s end carefully with a
fine brush.
4. Insert the mesh filter again. Connect the inlet hose to
water tap and washing machine again. Do not use a tool
to connect the inlet hose. Open the water tap and check
that all connections are tight.
2
1
CLEANING THE DETERGENT DISPENSER
Open the detergent dispenser drawer and
pour in the detergent or washing additive,
as follows.
1
2
3
CLEANING THE WATER FILTER / DRAINING RESIDUAL WATER
Switch off and unplug the washing machine before cleaning the water filter or draining residual water. If you used a hot
wash programme, wait until the water has cooled down before draining any water.
Clean the water filter regularly, to avoid that the water cannot drain after the wash due to obstruction of the filter.
If the water cannot drain, the display indicates that the water filter may be clogged.
1. Remove the kick panel: Using a screwdriver, do that which
is shown in the following figure.
4. Remove filter: Lay a cotton cloth beneath the water filter,
which can absorb a small amount of rest water. Then
remove the water filter by turning it out anticlockwise.
2. Container for the drained water:
Place a low and wide container under the water filter in
order to collect the residual water.
5. Clean the water filter: remove residues in the filter and
clean it under running water.
3. Drain the water:
Slowly turn the filter counter-clockwise until all the water
has come out. Allow the water to flow out without
removing the filter. Once the container is full, close the
water filter by turning it clockwise. Empty the container.
Repeat the procedure until all the water has been drained.
6. Insert the water filter and reinstall the plinth: Reinsert the water
filter again by turning it in clockwise direction. Make sure to turn
it in as far as it goes; the filter handle must be in vertical position.
To test water tightness of the water filter, you can pour about 1
liter of water into the detergent dispenser. Then reinstall the
plinth.
2
1
TRANSPORT AND HANDLING
Never lift the washing machine by holding it at the worktop.
1. Pull out the mains plug, and close the water tap.
2. Make sure that door and detergent dispenser are properly
closed.
3. Disconnect the inlet hose from the water tap, and remove
the drain hose from your draining point. Remove all rest
water from the hoses, and fix them so that they cannot get
damaged during transport.
4. Refit the transport bolts. Follow the instructions for
removing the transport bolts in the “Installation Guide” in
reverse order.
Important: Do not transport the washing machine without
having fixed the transport bolts.
AFTER-SALES SERVICE
BEFORE CALLING THE AFTER-SALES SERVICE
1. See if you can solve the problem by yourself with the help
of the suggestions given in the TROUBLESHOOTING
IF AFTER THE ABOVE CHECKS THE FAULT STILL
OCCURS, GET IN TOUCH WITH THE NEAREST
AFTER-SALES SERVICE
To receive assistance, call the number shown on the warranty
booklet or follow the instructions on the website
www.aristonbrand.com
When contacting our Client After sales service, always specify:
• a brief description of the fault;
• the type and exact model of the appliance;
xxxxxxxxxxxx
2. Switch the appliance off and back on again to see if the
fault persists.
•
the service number (number after the word Service on the
rating plate).
• your full address;
• your telephone number.
If any repairs are required, please contact an authorised aftersales service (to guarantee that original spare parts will be used
and repairs carried out correctly).
10 mm - 0,39 inch
3.
2.
1.
150 ml
100 ml
50 ml
4.
2 cm - 0,7 inch
6.
5.
7.
8.
9.
max 0,5 cm
max 0,2 inch
10.
11.
12.
max 100 cm
39 inch
min 65 cm
25 inch
max 100 cm
39 inch
min 65 cm
25 inch
max 100 cm
39 inch
min 65 cm
25 inch
13.
14.
SAFETY INSTRUCTIONS
Before using the appliance, read these safety instructions. Keep them nearby for future reference. These
instructions and the appliance itself provide important safety warnings, to be observed at all times.
The manufacturer declines any liability for failure to
observe these safety instructions, for inappropriate
use of the appliance or incorrect setting of controls.
Very young children (0-3 years) should be kept
away from the appliance. Young children
(3-8 years) should be kept away from the
appliance unless continuously supervised.
Children from 8 years old and above and persons
with reduced physical, sensory or mental
capabilities or lack of experience and knowledge
can use this appliance only if they are supervised
or have been given instructions on safe use and
understand the hazards involved. Children must
not play with the appliance. Cleaning and user
maintenance must not be carried out by children
without supervision. Never open the door forcibly
or use it as a step.
PERMITTED USE
CAUTION: The appliance is not intended to be
operated by means of an external switching
device, such as a timer, or separate remote
controlled system.
This appliance is intended to be used in
household and similar applications such as: staff
kitchen areas in shops, offices and other working
environments; farm houses; by clients in hotels,
motels, bed & breakfast and other residential
environments; areas for communal use in blocks
of flats or in launderettes.
Do not load the machine above the maximum
capacity (kg of dry cloth) indicated in the
programme table.
This appliance is not for professional use. Do
not use the appliance outdoors.
Do not use any solvents (e.g. turpentine,
benzene), detergents containing solvents,
scouring powder, glass or general purpose
cleaners, or flammable fluids; do not machine
wash fabrics that have been treated with solvents
or flammable liquids.
INSTALLATION
The appliance must be handled and installed
by two or more persons - risk of injury. Use
protective gloves to unpack and install - risk of
cuts.
If you want to stack a dryer on top of your
washing machine, first contact our After-Sales
Service or your specialist dealer to verify whether
this is possible. This is only possible if the dryer is
attached to the washing machine by means of
appropriate stacking kit available through our
After- Sales Service or your specialist dealer.
EN
IMPORTANT TO BE READ AND OBSERVE
Move the appliance without lifting it by the
worktop or top lid.
Installation, including water supply (if any) and
electrical connections and repairs must be carried
out by a qualified technician. Do not repair or
replace any part of the appliance unless
specifically stated in the user manual. Keep
children away from the installation site. After
unpacking the appliance, make sure that it has not
been damaged during transport. In the event of
problems, contact the dealer or your nearest
After-sales Service. Once installed, packaging
waste (plastic, styrofoam parts etc.) must be
stored out of reach of children - risk of suffocation.
The appliance must be disconnected from the
power supply before any installation operation risk of electric shock. During installation, make
sure the appliance does not damage the power
cable - risk of fire or electric shock. Only activate
the appliance when the installation has been
completed.
Do not install your appliance where it may be
exposed to extreme conditions, such as: poor
ventilation, temperatures below 5 °C or above 35 °C.
When installing the appliance make sure that
the four feet are stable and resting on the floor,
adjusting them as required, and check that the
appliance is perfectly to level using a spirit level.
If the appliance is being installed on wood or
“floating” floors (certain parquet and laminate
materials), secure a 60 x 60 x 3 cm (at least) sheet
of plywood to the floor then place the appliance
on top of this.
Connect the water inlet hose(s) to the water
supply in accordance with the regulations of your
local water company.
For cold fill only models: do not connect to the
hot water supply.
For models with hot fill: the hot water inlet
temperature must not exceed 60 °C.
The washing machine is fitted with transport
bolts to prevent any possible damage to the
interior during transport. Before using the
machine, it is imperative that the transport bolts
are removed. After their removal, cover the
openings with the 4 enclosed plastic caps.
After installation of the device, wait a few hours
before starting it so that it acclimates to the
environmental conditions of the room.
Make sure that the ventilation openings in the
base of your washing machine (if available on
your model) are not obstructed by a carpet or
other material.
Use only new hoses to connect the appliance
to the water supply. The old hose-sets should not
be reused.
The supply water pressure must be in the 0.1-1
Mpa range.
ELECTRICAL WARNINGS
It must be possible to disconnect the appliance
from the power supply by unplugging it if plug is
accessible, or by a multi-pole switch installed
upstream of the socket in accordance with the
wiring rules and the appliance must be earthed in
conformity with national electrical safety
standards.
Do not use extension leads, multiple sockets or
adapters. The electrical components must not be
accessible to the user after installation. Do not use
the appliance when you are wet or barefoot. Do
not operate this appliance if it has a damaged
power cable or plug, if it is not working properly,
or if it has been damaged or dropped.
If the supply cord is damaged, it must be
replaced with an identical one by the
manufacturer, its service agent or similarly
qualified persons in order to avoid a hazard - risk
of electric shock.
CLEANING AND MAINTENANCE
WARNING: Ensure that the appliance is
switched off and disconnected from the power
supply before performing any maintenance
operation; never use steam cleaning equipment risk of electric shock.
DISPOSAL OF HOUSEHOLD APPLIANCES
This appliance is manufactured with recyclable or reusable materials.
Dispose of it in accordance with local waste disposal regulations.
For further information on the treatment, recovery and recycling
of household electrical appliances, contact your local authority,
the collection service for household waste or the store where you
purchased the appliance. This appliance is marked in compliance
with European Directive 2012/19/EU, Waste Electrical and Electronic
Equipment (WEEE). By ensuring this product is disposed of correctly,
you will help prevent negative consequences for the environment and
human health.
The symbol on the product or on the accompanying documentation
indicates that it should not be treated as domestic waste but must be
taken to an appropriate collection center for the recycling of electrical
and electronic equipment.
DISPOSAL OF PACKAGING MATERIALS
The packaging material is 100% recyclable and is marked with the
recycle symbol .
The various parts of the packaging must therefore be disposed of
responsibly and in full compliance with local authority regulations
governing waste disposal.
11380053
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising