Indesit | WFCDM11 | Setup and user guide | Indesit WFCDM11 Setup and user guide

Indesit WFCDM11 Setup and user guide
8
Quick guide
3’’
THANK YOU FOR BUYING A WHIRLPOOL PRODUCT.
In order to receive a more complete assistance,
please register your product on
www.whirlpool.com.au
2
Before using the appliance carefully
read the Safety Instructions.
h
4
CONTROL PANEL
ON/OFF button (Reset if long pressed)
Programme selection Knob
Start/Pause
Options buttons*
4 Dryness level
5 Start delay
6 Timed drying
7 Cycle end
8 Rapid (Key lock if long pressed)
9 Fresh care+ (Mute if long pressed)
EN
5
6
1
2
3
3
7
9
1
3’’
8
3’’
3
h
2
4
5
6
7
*Note: some models may have the wording in full instead of the icons
INDICATORS
Cycle phase:
Drying - Cool down - End of cycle.
Empty water tank Clean door filter Clean bottom filter Refer to Troubleshooting section:
Failure: Call after sales service DEMO Demo mode
FIRST TIME USE
PROGRAMS
Make sure that the water tank is correctly inserted. Make sure
that the drain hose on the back of the dryer is fixed correctly,
either to the dryer’s water tank, or to your domestic sewage
system.
Eco cotton
kg Max*
Standard cotton programme, suitable to dry normally wet cotton
laundry. Most efficient programme in terms of energy consumption
for drying cotton laundry. The values on the Energy Label are based on
this programme.
Mixte
kg 4 This programme is ideal for drying cotton and synthetic fabrics
together.
Bed linen
Kg Max*
This programme is intended for drying cotton sheets.
Shirts kg 3 This is a programme for Shirts made from cotton or cotton
blend/synthetics.
Sport
kg 4 For drying sports garments made of synthetics or cotton.
Duvet
Programme intended to dry bulky garments, as single duvet.
Jeans
kg 3 For drying cotton jeans-wear and garments made of robust
cotton, like denim, such as trousers and jackets.
Easy ironing
This cycle allows to extend the fibres of garments thus making
ironing and folding easier. Do not use in case of garments that are
still wet. Suitable for small loads of cotton textiles or cotton blends.
Refresh
A short programme suitable for refreshing fibres and garments by
means of fresh air. Do not use with garments that are still wet. It can be
used on with any load size but is more effective with small loads. The
cycle duration is about 20 minutes.
DAILY USE
Doing this will keep your machine working at its BEST!
Remember to empty your water tank after each drying cycle.
Remember to clean your filters after each drying cycle. (Refer
to section Care & Maintanence).
1. Open the door and load garments. Always refer to instructions
on clothing labels and the max loads indicated in the programme
section. Empty pockets. Make sure garments do not get caught
between the door and/or the door filter.
2. Close the door.
3. Press the button On/Off.
4. Select the programme according to the laundry type.
5. Select the options, if necessary.
6. To start the cycle, press the Start/Pause button.
7. At the end of the drying cycle, a buzzer will beep. An indicator on
the control panel signals the end of the cycle. Pull the load out
immediately to prevent the formation of creases on laundry
8. Turn the machine off by pressing the button On/Off, open the
door and pull clothing out. If the machine is not switched off
manually, after about a quarter of an hour from the cycle end, the
appliance turns off automatically to save energy.
If this last stage is not carried out immediately, some machines
and/or some programmes/options are equipped with Crease Care
system. For some hours, after the end of drying, the drum rotates
at regular intervals to prevent the formation of creases. In case of
power failure, it is necessary to press the button Start/Pause to
restart the cycle.
OPENING OF THE DOOR DURING THE CYCLE
*MAX LOAD 8 Kg
During operation, it is possible to open the door. After having
can download
the again
Safetyto
Instructions,
ManualCARE
by:
closed it, press theYou
button
Start/Pause
restart theUser
dryer.
LABEL
(Dry load)
xxxx
xxxxxxxxxxxx
• Visiting our website - docs.whirlpool.eu
Always check the care labels, especially when placing garments in
• Using QR Code
the tumble
the firstbooklet).
time. Below
• Alternatively, contact our After-sales Service (See phone
numberdryer
in thefor
warranty
When are the most commonly
usedprovided
symbols:
contacting our After-sales Service, please state the codes
on your product’s identification plate.
May be tumble dried.
Do not tumble dry.
Tumble dry – high heat.
Tumble dry – low heat.
The duration of these programs will depend on the size of the
load, types of textiles, the spin speed used in your washer and
any extra options selected. In machines equipped with display,
the duration of the cycles is shown on the control panel. The
remaining time is constantly checked and adjusted during the
drying cycle to show the best possible estimate.
Rapid 30'
kg 0,5
Ideal for drying cotton garments spun at high speed in the
washing machine.
Coloured
kg Max*
Programme for gentle drying suitable for coloured garments.
Silkkg 0,5 Gentle drying of silk garments.
Wool kg 1 Programme for drying wool clothing. It is advisable to turn
the garments inside out before drying. Leave to dry naturally the
heaviest edges that are still damp.
Delicates
kg 2 For drying delicate laundry which needs gentle treatment.
Synthetics
kg 4 For drying laundry made of synthetic fibres.
OPTIONS BUTTONS
These buttons serves to personalise the selected programme
according to personal requirements. Not all options are available
for all programmes. Some options are incompatible with the
ones previously set. The buzzer and/or blinking indicators will
signal the incompatibility. If the option is available, the option
indicator will stay on. Some options may be kept in the memory
of the programme if selected in the previous drying.
OPTIONS
After selecting the programme, the various options can be
set, if necessary.
Dryness level
Press the related button several times to obtain a different
level of residual moisture on garments. An indicator signals the
level being selected.
Iron dry: a very delicate ironing. Suitable for making ironing of
garments easier immediately after the end of the cycle.
Hanger dry: a level intended for delicate garments ready to
be hanged.
Cupboard dry: the garments are ready to be folded and put
away.
Extra dry: used for garments to be worn at the end of the
cycle.
Timed drying
This option allows to set the drying time. Press the
corresponding button to set the required time for drying. An
indicator on the control panel signals the time being selected.
Start delay
h
This option allows you to set the delay of the cycle start. Press
the corresponding button several times to obtain the required
delay. After having reached the max. settable time, the option is
reset by pressing the button again. An indicator on the control
panel signals the time being selected. After having pressed the
button Start/Pause, the machine signals the remaining time
for the cycle start. In case of door opening, after closing, it is
necessary to press the button Start/Pause.
Rapid
Enables quicker drying.
Fresh care+
If garments are left inside the drum after the end of the
cycle, they are subject to bacterial proliferation. This option allows
to prevent this proliferation by controlling the temperature and
the rotation of the drum. This treatment has a max. duration of 6
hours after the end of the programme set. This option remains in
memory if selected in the previous drying.
If this option is used together with the Start Delay, a crease
treatment (a periodic rotation of the drum) is added in the Start
Delay phase.
Key lock
This option makes all machine controls inaccesible, except
the button On/Off. When the machine is on: to activate the
option, keep the button pressed until the indicator goes on. To
disable the option, keep the button pressed until the indicator
goes off. This option remains in memory if selected in the previous
drying.
Mute
This option turns off all sounds of control panel. Only
warnings remain active.
• to activate the option, keep the button pressed until the
indicator goes on.
• to disable the option, keep the button pressed until the indicator
goes off.
Cycle end
This option activates a prolonged buzzer at the end of the
cycle. Enable it if you are not sure to hear the normal sound at the
end of the cycle. This option remains in memory if selected in the
previous drying.
EN
Quick guide
THANK YOU FOR BUYING A INDESIT PRODUCT.
The filters are essential parts for drying. They are intended
CARE AND
In orderMANTENANCE
to receive a more complete assistance,
collect
lint formed
during
drying
process.
In case
Before
thethe
appliance
carefully
read
the Safety
Instructions.
please
register
your
product
on
Unplug the dryer during the cleaning and maintenance tousing
of
clogged
filters,
the
air
flow
inside
the
dryer
would
be
www.indesit.eu/register
procedures.
seriously affected: the drying times would be longer, the
Emptying the water tank after each cycle (see Fig. A).
energy consumption would increase and the dryer could be
Pull the container out of the dryer and and empty it into a
damaged. If these procedures are not carried out properly,
sink or other suitable drain, then place it back. Do not use the dryer the dryer may not start.
without having inserted the container back in place.
Cleaning the door filter after each cycle (see Fig. B).
TRANSPORT AND HANDLING
Pull the filter out and clean it by removing the lint from the
filter surface under running water or using a vacuum cleaner. For Never lift the dryer by holding it at the worktop.
optimal performance, dry up all the filters before inserting them 1. Unplug the dryer.
back in place. Do not use the dryer without having reinserted the 2. Make sure that door and water tank are properly closed.
filter in place.
3. If the drain hose is connected to your sewage system, fix the
drain hose on the rear of the dryer again (see Installation Guide).
Remove the door filter as described below:
1. Open the door and pull upwards.
2. Open the filter and remove lint from all its parts. Replace it
Power consumption
correctly.
off-mode (Po) - Watts
0.50
Ensure it is completely inserted flush with the dryer seal.
left-on mode (Pl) - Watts
1.00
Cleaning the bottom filter when the relevant indicator
turns on (see Fig. C).
Programs
Kg
kWh
Minutes
Pull the filter out and remove the lint from its surface by washing
8
4.76
130
it under runing water or by using a vacuum cleaner.
Eco Cotton *
However, it is advisable to clean this filter after each cycle to
4
2.47
70
Eco Cotton
optimise drying performance. Do not use the dryer without
Synthetics
4
1.83
90
having inserted the filter in place first.
Remove the bottom filter and the condenser as described
*Test programme according to AS/NZS 2442.2 standard. Tested with
below:
maximum rated load capacity and dryness level Extra Dry.
1. Open the bottom door.
2. Take the handle and pull the bottom filter out.
3. Open the rear side of the filter and remove the lint from the
inner surface of the mesh.
4. Clean the bottom filter chamber (there might be residual
water: this is normal).
5a. Approximately every 3 months, clean the condensing unit
(figure D) situated behind the bottom filter.
5b. Lower the levers situated on the sides of the condenser. After
having removed the condenser, clean it under running water.
5c. Place the condenser back in place and lift the levers.
6. Close the rear side of the bottom filter and place it back by
checking it is perfectly integrated in place.
7. Lower the filter handle and close the bottom door.
8. Make sure the air intake is free.
PRODUCT DESCRIPTION
1.
2.
3.
4.
Water Tank
Air Intake
Bottom filter and condenser
Door filter
A
1
C
B
D
You can download the Safety Instructions, User Manual, Product Fiche and Energy data by:
• Visiting our website - docs.indesit.eu
• Using QR Code
• Alternatively, contact
our After-sales Service (See phone number in the warranty booklet). When
4
2
contacting our After-sales Service, please state
the codes provided on your product’s identification plate.
3
xxxx
xxxxxxxxxxxx
EN
Quick guide
THANK YOU FOR BUYING A WHIRLPOOL PRODUCT.
In order to receive a more complete assistance,
TROUBLESHOOTING
Beforethe
using
the appliance
carefully
thesolved
Safety
please register
product
on refer to the table below. Often
Before contacting
theyour
Service
Centre,
malfunctions
are minor
and read
can be
inInstructions.
few minutes
www.whirlpool.com.au
Malfunction
The tumble
dryer does not
turn on.
The tumble
dryer does not
start
The drying
times are very
long
Possible cause
The plug is not inserted into the socket.
Solution
Insert the plug into the socket.
The plug is faulty.
Try to plug another appliance in the same socket. Do not use
connecting electrical devices to the socket, as adapters or extensions
A power failure occurred.
Await the reactivation of the power supply.
The door is open.
Close the door.
For machines equipped with this function: await the end of the delay
set or switch the machine off to reset it. Refer to the section Options.
A time delay for the cycle start was set.
The button Start/Pause was not pressed to start Press the button Start/Pause.
the program.
The function Key Lock was enabled (in case of
machines equipped with this option).
Refer to the option section and, if the Key Lock is present, disable it.
Switching the machine off is not enough to disable this option.
An appropriate maintenance was not carried
out.
The programme, the time and/or the drying
level set are not suitable for the type and the
amount of load inserted into the dryer.
Refer to the section Care & Maintenance and perform the operations
described.
The garments are too wet.
Carry out a washing cycle with higher spin speed to remove as much
water as possible.
Refer to the programme section to check the max. load for each
programme.
In case of power failure, it is necessary to press the button Start/Pause
to restart the cycle.
The dryer may be overloaded.
The programme A power failure occurred might have occurred.
did not end.
Lights on or flashing
Refer to the section programmes and options to find the programme
and the options most suitable for the type of load.
Water tank
The water tank is full.
Emtpy the water tank. Refer to the section Care & Maintenance.
Door filter
and/or bottom
filter*
Failure of the air flow necessary for machine
operation.
Clean the door filter and the bottom one and check whether air
intake is free. Carrying out these operations improperly may cause
damages.
Bottom filter*
The bottom filter requires cleaning.
Clean the bottom filter. Refer to section Care & Maintanence.
DEMO
The cycle lasts
few minutes.
The dryer is in DEMO mode. The DEMO
indicator is on.
The presence
of wrench
symbol signals a The machine sensors detected a failure.
malfunction.
Disable the DEMO mode. The following actions must be carried out
in sequence, without breaks. Switch the machine on and then switch
it off again. Press the Start/Pause button until the buzzer is heard.
Switch the machine on again. The “DEMO” indicator flashes and then
turns off.
Switch the dryer off and unplug it. Open the door immediately and
pull laundry out, to allow the heat to dissipate. Wait for about 15
minutes. Reconnect the dryer to the power supply, load the laundry
and restart the drying cycle. If the problem still occurs, contact
the After-Sales Service Centre and communicate the letters and
digits flashing on the display.
For instance: F3 and E2
*Note: some models are self-cleaning and not equipped with bottom filter. Please refer to the section Care & Maintenance.
You can download the Safety Instructions, User Manual by:
• Visiting our website - docs.whirlpool.eu
• Using QR Code
• Alternatively, contact our After-sales Service (See phone number in the warranty booklet). When
contacting our After-sales Service, please state the codes provided on your product’s identification plate.
W11392623
08/2019
xxxx
xxxxxxxxxxxx
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising