Russell Hobbs | product_180 | User manual | Russell Hobbs product_180 Product User Manual

Russell Hobbs product_180 Product User Manual
instructions
��������
���
����
������
�����
�����
�����
������
������
���
�����
���1
����������
�����
2
���0
������
Read the instructions and keep them safe. If you pass the kettle on to anyone else, you
should also pass on the instructions too.
Remove all packaging before using the kettle, but keep it till you’re satisfied that the
kettle is working.
important safeguards
When using electrical appliances, basic safety precautions should always be followed,
including the following:
1 This kettle must only be used by or under the direct supervision of a responsible
adult.
2 Don’t put the kettle, stand, cable, or plug in any liquid; don’t use the kettle
in a bathroom, near water, or outdoors.
3 Don’t touch hot surfaces. Use the handle and lid knob.
4 Don’t open the lid while the water is heating.
5 Take care when pouring – pour slowly, and don’t over-tilt the kettle.
6 Don’t connect this kettle to an external timer or remote control system.
7 Water can remain hot for a considerable time after boiling and can present a scald
hazard. Keep the kettle, the stand, and the cable away from the edge of worktops
and out of the reach of children.
8 Route the cable so it doesn’t overhang, and can’t be tripped over or caught
accidentally.
9 Unplug the stand when not in use, before moving and before cleaning. Let the
kettle cool down before cleaning and storing away.
10 Don’t use the kettle without the filter in place – it may spit boiling water.
11 Check the lid is properly closed before switching the kettle on, otherwise it may not
switch off.
12 Check the kettle is properly located on the stand before switching on.
13 Don’t switch on unless the kettle contains at least 2 cups of water.
14 Don’t fill past max, or the kettle may spit boiling water.
15 Remove the kettle from its stand before filling or pouring.
16 Keep the kettle, stand, cable, and plug away from sources of heat.
17 Don’t use the kettle for any purpose other than heating water.
18 Use the kettle only with the stand supplied (and vice versa).
19 Don’t operate the kettle if it’s damaged or malfunctions. If the cable or stand is
damaged, replace the stand, in order to avoid hazard.
household use only
before using for the first time
Remove all packaging from the kettle and its stand. Before using the kettle for the first
time, or if it has been out of use for a long time, fill to max, boil, discard the water, then
rinse. Do this three times to remove manufacturing dust, etc.
3
positioning
1 Put the stand on a stable, level surface. Route the cable so it doesn’t overhang, and
can’t be caught or tripped over.
filling
warning keep clear, steam may escape from the lid.
Check that the switch is off 0 – flip the switch up.
Remove the kettle from the stand.
Use the lid knob to lift off the lid.
Fill the kettle with at least 2 cups of water, but don’t fill above max.
Don’t overfill the kettle. If the kettle is overfilled, there is a risk it may spit boiling
water.
7 Replace the lid.
8 Check the lid is closed, otherwise the kettle may not switch off when it boils.
2
3
4
5
6
switching on
9
10
11
12
Check that the switch is off 0 – flip the switch up.
Plug the stand into the wall socket. If necessary, switch the socket on.
Gently position the kettle on the stand – take care not to spill any water.
Press the switch down to turn the kettle on 1. The lights will come on, and the kettle
will heat up.
switching off
13 When the water has boiled, the kettle will switch off automatically, the switch will
return to the off 0 position and the lights will go out.
14 The kettle can be switched off at any time before the water boils by flipping the
switch up to 0.
general
When you lift the kettle from the stand, you may see moisture on the surface of
the stand. This is the steam used to switch the kettle off automatically, which then
condenses and is allowed to escape via vents in the underside of the kettle. This is
normal, and should be ignored.
You may notice discolouration of the coating on the floor of the kettle. This occurs
during bonding of the element to the floor. It’s unavoidable, harmless, and should be
ignored.
Remove the kettle from the stand before pouring.
When filling or carrying the kettle, don’t tilt it backwards, as this may allow water to
pass through the steam aperture on to the control area. Should this occur, let the kettle
dry before use – sit it somewhere warm for 12 hours.
To avoid the risk of splashing, pour slowly and don’t over-tilt the kettle.
insufficient water
Don’t switch the kettle on unless it contains 2 cups of water. Misuse of this kind will
shorten the life of the element.
If the kettle is accidentally switched on when it doesn’t contain sufficient water, a boildry device will automatically switch it off. Remove it from the stand and let it cool down
fully before filling, as the element will be hot and spitting may occur.
4
care and maintenance
Switch the kettle off 0 – flip the switch up, unplug the stand from the wall socket, and
let the kettle cool down fully before cleaning. Wipe the kettle, inside and out, with a
damp cloth. If necessary, you may use a little household detergent.
If you use detergent inside the kettle, rinse thoroughly afterwards to remove all trace of
detergent, to avoid tainting the water.
Keep all connectors and sockets dry.
Don’t put the kettle, stand, cable, or plug in any liquid.
Don’t use harsh or abrasive cleaning agents or solvents.
descale regularly – even in soft water areas
Limescale may be white, coloured, even rusty-looking, but it’s normally visible.
Phosphate scale isn’t generally visible, but it’s there, even in soft water areas.
All scale causes overheating, reduces the kettle’s life, and may trigger the boil-dry cutout.
So, even with soft water, descale at least monthly, to help keep your kettle in working
order.
Use a descaler suitable for plastic products (all kettles have plastic parts). Follow the
instructions on the descaler, rinse several times, then fill, boil and discard the water, to
ensure no residues are left.
to minimise scale build-up
Empty the kettle after each use - never leave water in the kettle overnight.
If the water in your area is particularly hard, you may consider the use of filtered water
instead of ordinary tap water.
5
�����
�����
������
������
����
������
������
������
�����
���
���0
�����
������
���1
water filter
Scale particles suspended in the water may give it a cloudy or greasy appearance. The
filter will prevent these particles going into your drink. If you see deposits on the filter,
clean it, otherwise the performance of your kettle will drop, your drinks may contain
scale, and the water inside the kettle may look cloudy.
cleaning the filter
Switch the kettle off 0 – flip the switch up, unplug the stand from the wall socket, and
let the kettle cool down fully before cleaning.
Check your hands are free from soap, or anything which might leave a taint.
release the filter
Use the lid knob to open the lid.
Push the filter handle down to release the filter, then lift it out of the kettle.
Brush it with a soft brush, under a running tap.
Rinse the kettle, in case any scale particles have fallen inside.
replace the filter
Put the spike into the holder, then push the filter towards the spout till the tabs click
into the holes.
Replace the lid.
Press the lid down to make sure it’s properly closed.
warning Don’t use the kettle without the filter in place – it may spit boiling water.
6
7
connection
The product must be earthed. It has a 13A BS1362 fuse in a 13A BS1363
plug. To replace the plug, fit the green/yellow wire to E or E, the blue
wire to N, and the brown wire to L. Fit the cord grip. If in doubt, call an
electrician.
Don’t use a non-rewireable/moulded plug unless the fuse cover is in
place. If you remove the plug, dispose of it.
service
The product isn’t user-serviceable. If it’s not working, read the instructions, check the
plug fuse and main fuse/circuit breaker. If it’s still not working, consult your retailer. If
that doesn’t solve the problem:
Pack carefully, with a note of your name, address, day phone number, and what’s
wrong. If under guarantee, say where and when purchased, and include proof of
purchase (till receipt). Send it to Customer Returns (address below right). They’ll give
you an estimate for inspection/repair.
Customer Service
Customer Returns
(correspondence only)
Salton Europe Ltd
Salton Europe Ltd
Heath Mill Road
Failsworth
Wombourne
Manchester
Wolverhampton
M35 0HS UK
WV5 8AQ
Customer Service (service@saltoneurope.com)
telephone 0845 658 9700 (local rate number)
guarantee
439-533
Defects affecting product functionality appearing within one year of purchase
will be corrected by replacement or repair provided the product is used and
maintained in accordance with the instructions. Your statutory rights are not affected.
Documentation, packaging, and product specifications may change without notice.
8
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising