Whirlpool | AAR 160 C | Instruction for Use | Whirlpool AAR 160 C Instruction for Use

Whirlpool AAR 160 C Instruction for Use
AAR 160 C
ENGLISH Instructions for use
Page 2
1
INSTRUCTION FOR USE
IMPORTANT SAFETY INSTRUCTIONS
BEFORE USING THE GLASS CERAMIC HOB
INSTALLATION
ELECTRICAL CONNECTIONS
ENERGY SAVING TIPS
SAFEGUARDING THE ENVIRONMENT
CARE AND MAINTENANCE OF THE GLASSCERAMIC HOB
TROUBLESHOOTING GUIDE
AFTER SALES SERVICE
PRODUCT DESCRIPTION SHEET
2
IMPORTANT SAFETY INSTRUCTIONS
These instructions shall also be available on website:
docs.whirlpool.eu
YOUR SAFETY AND THAT OF OTHERS IS •
VERY IMPORTANT
•
This manual and the appliance itself provide important
safety messages, to be read and always observed.
WARNING:
All messages relevant to safety specify the potential
risk to which they refer and indicate how to reduce
the risk of injury, damage and electric shocks due to
incorrect use of the appliance. Make sure to comply
with the following:
• The appliance must be disconnected from the
power supply before carrying out any installation
operation.
• Installation and maintenance must be carried out
by a specialised technician, in compliance with
themanufacturer’s instructions and the local safety
regulations in force. Do not repair or replace any
part of the appliance unless specifically stated in
the user manual.
• The appliance must be earthed.
• The power cable must be long enough for
connecting the appliance, fitted in the cabinet, to
the power supply.
• For installation to comply with the current safety
regulations, an omnipolar switch with minimum
contact gap of 3 mm is required.
• Do not use multi-sockets or extension cords.
• Do not pull the appliance’s power cable.
• The electrical parts must not be accessible to the
user after installation.
• The appliance is designed solely for domestic use
for cooking food. No other use is permitted (e.g.
heating rooms). The Manufacturer declines any
liability for inappropriate use or incorrect setting of
the controls.
• The appliance and its accessible parts become hot
during use. Care should be taken to avoid touching
heating elements. Children less than 8 years old
shall be kept away unless continuously supervised.
• The accessible parts can become very hot during
use. Children must be kept away from the appliance
and watched over to ensure they do not play with it.
• Do not touch the appliance heating elements
during and after use. Do not allow the appliance to
•
•
•
•
•
•
come into contact with cloths or other flammable
materials until all the components have cooled
sufficiently.
Do not place flammable materials on or near the
appliance.
Overheated oils and fats catch fire easily. Pay
attention when cooking food products rich in fat
and oil.
This appliance can be used by children aged from
8 years and above and persons with reduced
physical, sensory or mental capabilities or lack of
experience and knowledge if they have been given
supervision or instruction concerning use of the
appliance in a safe way and understand hazards
involved.Cleaning and user maintenance shall not
be made by children without supervision.
If the surface is cracked,switch off the appliance to
avoid the possibility of electric shock.
The appliance is not intended to be operated by
means of an external timer or separate remote
control system.
Unattended cooking on a hob with fat or oil can
be dangerous and may result in fire. NEVER try
to extinguish a fire with water, but switch off the
appliance and then cover flame e.g. with a lid or a
fire blanket. Danger of fire: do not store items on
the cooking surfaces.
Do not use steam cleaners.
Metallic objects such as knives,forks, spoons and
lids should not be placed on the hob surface since
they can get hot.
3
BEFORE USING THE GLASS CERAMIC HOB
• To make the most of your new appliance, please read the user
instructions carefully and keep them handy for future consultation.
INSTALLATION
Important
In order to prevent the electronic circuits from overheating, and therefore from
being damaged, we recommend the following:
• Do not install the cooktop near a dishwasher or washing machine,
so that the electronic circuits do not come into contact with steam
or moisture, which could damage them.
Rear wall
min. 5 mm
Cooktop
• The cooktop must be set into a worktop between 20 mm and 50 mm
deep
• There must be nothing between the cooktop and the oven (cross
rails, brackets, etc.).
• The distance between the lower face of the glass ceramic hob and the
cupboard or separating panel must be at least 20 mm.
• If the cooktop is to be installed next to a column unit, leave a distance
of at least 100 mm from the edge of the cooktop to the side of the
column unit.
• Make an opening in the worktop, respecting the dimensions indicated in
the enclosed product description sheet.
• Apply the supplied gasket to the cooktop (unless it has already been fitted),
after having cleaned its surface.
min. 20 mm
min. 5 mm
1
2
If an oven (from our range of ovens) is installed beneath the cooktop, make
sure that it is equipped with a cooling system.If the temperature of the
electronic circuits exceeds the maximum permitted temperature, the cooktop
will switch off automatically; in this case, wait for a few minutes until the internal
temperature of the electronic circuits reaches a tolerable level, at which point
it will be possible to switch the hob on again.
• Switch the hob off after use.
3
4
Front
ELECTRICAL CONNECTIONS
Electrical connection must be made before connecting the appliance to the
electricity supply. The appliance must be installed by a qualified electrician
who is fully aware of current safety and installation regulations. Specifically,
installation must be carried out in compliance with the regulations of the local
electricity supply company. Make sure that the voltage shown on the rating
plate is the same as the power supply voltage in your home. Regulations
require that the appliance be earthed: use conductors (including the earth
conductor) of the appropriate size only. The manufacturer declines all liability
for injury to persons or animals and for damage to property resulting from
failure to observe the above regulations. For the electrical connection use a
H05RR-F type cable as indicated in the table below:
Power supply voltage.
Conductors
Amount x size
220-240V ~ +
3 x 4 mm2
230-240V ~ +
3 x 4 mm2 (Australia only)
220-240V 3~ +
4 x 1,5 mm2
380-415V 3N~ +
5 x 1,5 mm2
380-425V 2N~ +
4 x 1,5 mm2
The appliance must be connected to the electricity supply by means
of an all-pole disconnect switch with minimum contact gap of 3 mm.
Attention: the power supply cable must be long enough to allow the cooktop to
be removed from the worktop and must be positioned so as to avoid damage
or overheating caused by contact with the base.
Connecting to the terminal board
Note: the yellow/green earth wire must be connected to the terminal with the
symbol
and must be longer than the other wires.
• Remove approx. 70 mm of the cable sheath from the power supply cable
(B).
• Strip approx. 10 mm of sheath from the wires. Then insert the power supply
cable into the cable clamp and connect the wires to the terminal block as
indicated in the connection diagram placed close to the terminal block itself.
• Secure the power supply cable (B) by means of the cable clamp.
• Close the terminal board with the cover (A) securing it with the screw
provided.
• After the electrical connection, fit the hob from the top and hook it to the
support springs, according to the illustration.
ENERGY SAVING TIPS
• Use pots and pans whose bottom diameter is equal to that of the cooking
zone or slightly larger.
• Only use flat-bottomed pots and pans.
• If possible, keep pot lids on when cooking.
• Cook vegetables, potatoes, et. with little water in order to cut down cooking
time.
• A pressure cooker allows you to save even more energy and time.
NO!
5
SAFEGUARDING THE ENVIRONMENT
1. Packing
• The packaging material can be 100% recycled, as confirmed by the
recycling symbol
.
2. Products
This appliance is marked according to the European directive 2012/19/EU on
Waste Electrical and Electronic Equipment (WEEE). By ensuring this product
is disposed of correctly, you will help prevent potential negative consequences
for the environment and human health.
The symbol
on the product, or on the documents accompanying the
product, indicates that this appliance may not be treated as household
waste. Instead it shall be handed over to the applicable collection point for
the recycling of electrical and electronic equipment. Disposal must be carried
out in accordance with local environmental regulations for waste disposal.
For more detailed information about treatment, recovery and recycling of this
product, please contact your local authority, the household waste disposal
service or the shop where you purchased the product.
Declaration of conformity CE
• This cooktop is suitable for contact with foodstuffs and complies with EEC
(CE) Regulation n. 1935/ 2004.
• The appliances are designed solely for use as cooking appliances. Any
other use of the appliances (e.g. for room heating) is considered as improper
use and potentially dangerous.
• The appliances are designed, built and sold in compliance with:
• safety objectives of the “Low Voltage” Directive 2006/95/EC (which replaces
73/23/EEC and subsequent amendments);
• the protection requirements of Directive “EMC” 2004/108/EC;
CARE AND MAINTENANCE OF THE GLASS-CERAMIC HOB
Clean the cooktop, when it is cool, after each use. This will prevent the buildup of dirt and make cleaning easier.
Important: avoid the use of high pressure water or steam cleaning equipment.
• Use a clean cloth, absorbent kitchen wipes and washing up liquid or a
specific glass ceramic cleaner.
• Remove baked-on dirt with the special scraper tool (if provided) and specific
cleaning products.
• Food spills should be cleaned off before they bake onto the glass ceramic
surface.
• Foods with high sugar content (toffee, fruit juice, jam, etc.) that boil over
while cooking, or spattered sugar stains must be immediately removed
using a scraper.
• Do not use abrasive products, bleach, oven-cleaner spray or pan scourers.
The cooktop should be treated periodically with a proprietary brand of
protective wax for glass-ceramic hobs.
TROUBLESHOOTING GUIDE
Cooktop not working
• When pressing the control buttons, did you follow the instructions in the
section “Using the hob” in the enclosed “Product Description Sheet”?
• Is there perhaps a power failure?
• Did you dry the hob carefully after cleaning it?
1. If a cooking zone has been selected and an “F” or an “ER” appear on the
display followed by a number, contact the After Sales Service and inform
them.
AFTER-SALES SERVICE
Before contacting After-sales Service:
1. Try to solve the problem (see “Troubleshooting Guide”).
2. Turn off the appliance and restart it to see if the fault is repeated
If after the above checks the fault still occurs, get in touch with the
nearest After Sales Service.
Please give: a short description of the fault,
• the precise type and model of the appliances,
• the service number (the number after the word “Service” on the data plate),
located under the hob or on the Product Description Sheet.
6
-- With the exception of the message “F03” or “ER03” that identifies the
incorrect cleaning of the controls area.
-- To solve the problem follow the instruction in the ICleaning and
maintenance of the glassceramic hobI paragraph.
2. If the hob does not work following intensive use, the hob internal
temperature is too high. Wait a few minutes until the hob cools down.
• your complete address and phone number. If any repairs are required,
please contact an authorized After-sales Service as indicated in the
warranty. In the unlikely event that an operation or repair is carried out by an
unauthorised technician, always request a certification of the job carried out
and insist on the use of original spare parts. Failure to comply with these
instructions may compromise the safety and quality of the product.
PRODUCT DESCRIPTION SHEET
1.
2.
3.
4.
5.
1
4
Radiating cooking zone Ø 145
Radiating cooking zone Ø 180
Radiating cooking zone Ø 145
Radiating cooking zone Ø 210
Display
3
2
5
DIMENSIONS OF THE HOB (mm)
0
560+2 mm
R = Min. 6,5 mm
Max. 8 mm
580 mm
510 mm
482 mm
min 20 mm
0
490 +2 mm
R = 11,5 mm
552 mm
0
583 +2 mm
R = Min. 6,5 mm
0
0
0
513 +2
mm
560+2 mm
490+2 mm
6 mm
min. 5 mm
42 mm
Min. 70 mm
min. 20 mm
min. 5 mm
Min. 40 cm
Min. 7 cm
Min. 10 cm
7
C
D
B
A
E
H
A
On/Off
D
Key lock
B
Cooking zone and timer selection
C-E
Heat setting increase and decrease
Upon first installation, the control panel performs a functional test for about 1 second,
after which it automatically switches to the “Key lock” function.
To deactivate the function, press and hold button “D”; an acoustic signal will sound and
the corresponding led will turn off.
NOTE: If a reset occurs, repeat the procedure described above.
To switch the hob on, keep button “A” pressed for approx. 2 seconds. The 4 cooking zone
displays show “0”. If within 20 seconds none of the cooking zones is activated, the hob switches
off automatically as a safety precaution. Press one of the buttons “B” corresponding to the cooking
zone you intend to use. Select the heat setting required with buttons “E” or “C”. The other selectable
cooking settings go from 1 to 9. Press buttons +/- at the same time to cancel all settings.
Pressing button “+” when level 9 is reached, the “Booster” function is activated and the letter “A”
appears on the display.
IMPORTANT: the control is deactivated 10 seconds after the heat setting has been selected.
To change the heat setting, first press the selection button “B” again, then proceed to change
the setting, using buttons “E” or “C”.
MULTIPLE ZONE (if present): After selecting the desired zone and setting the level
(as described in the previous section) press “F”: an indicator above the button turns on,
activating the additional zone.
The multiple zone can only be used if:
1) The cooking zone is provided with multiple zone;
2) The power level selected is greater than 0.
To deactivate the multiple zone, press button “B” of the desired zone, then press “F” again.
To set the Timer function, select the desired cooking zone and power setting then press
the cooking zone key again and a luminous dot will appear on the display of the timer-controlled
cooking zone. The indication “00” blinks on the 2 displays. Press buttons “C” or “E” to set the time
from 1 to 99.
IMPORTANT: after 10 seconds the timer displays will show the power setting of the other cooking zones.
To view the remaining cooking time, press the timer-controlled cooking zone key twice.
The KEY LOCK function is switched on by holding down button “D” until a dot lights up above
the function button. The Key lock function locks all the hob’s other functions, with the exception of the
On/Off button “A”. The function remains on even after the hob is switched off and on again and
can be deactivated by pressing button “D” again until the dot above the function button goes off.
RESIDUAL HEAT INDICATOR
When the cooking zone is switched off, the residual heat indicator “H” remains on or flashes
alternating with “0” until the temperature of the hob returns within safety levels.
IMPORTANT: The hob’s safety features include an automatic switching off function. Prolonged use of the same heat
setting triggers automatic switch-off of the cooking zone (for example, after around 1 hour at maximum heat setting, the
cooking zone switches off).
BE CAREFUL: To avoid permanently damaging the glass-ceramic top, do not use:
- Pots with bottoms that are not perfectly flat.
- Metal pots with enamelled bottom.
Any aesthetic defects (scratches, surface marks, etc.) must be reported immediately upon installation.
8
GB
400011205240
11/17
9
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising