Bauknecht | BCIF 3O33 DELTS | Instruction for Use | Bauknecht BCIF 3O33 DELTS Instruction for Use

Bauknecht BCIF 3O33 DELTS Instruction for Use
EN
THANK YOU FOR PURCHASING A BAUKNECHT PRODUCT.
To receive more comprehensive help and support, please register your product at:
www.bauknecht.eu/register
Before using the appliance carefully read Health and Safety guide.
The control panel of this dishwasher activates pushing by ON/OFF button.
For energy saving the control panel deactivates automatically after 10 minutes if no cycle has started.
PRODUCT DESCRIPTION
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
1
2
8
9
3
10
4
11
5
Upper rack
Cutlery rack
Foldable flaps
Upper rack height adjuster
Upper sprayer arm
Power Clean support
Lower rack
Lower sprayer arm
Filter Assembly
Salt reservoir
Detergent and Rinse Aid dispensers
Rating plate
Control panel
6
Service:
12
7
0000 000 00000
13
CONTROL PANEL
1
2
1. ON-OFF button
2. CYCLES 6 buttons for direct acces popular cycles
3. EXTRA CYCLES button. Access to other cycles
4. INFO button. Provide info for selected cycle
5. DISPLAY - Indicators area
6. DISPLAY - Information area
7. PREVIOUS button for options/settings
8. OK button. Select/change options and settings
9. NEXT button for options/settings
10. START button
3
4
5
6
7
8
9
10
DISPLAY - INDICATORS
A
B
C
D
E
I
H
GF
A.
B.
C.
D.
E.
F.
G.
H.
I.
START DELAY
ECO CYCLE
MULTIZONE - Cutlery rack
CLOSED WATER TAP
ADD SALT
MULTIZONE - Upper Rack
MULTIZONE - Lower Rack
ADD RINSE AID
TABLET
1
EN
FIRST TIME USE
After connecting the appliance to the power supply for the first time,
the display will guide you to set up the appliance for first use.
Once done, proceed to the next step by pressing „OK” button.
1. The language selection
LANGUAGE: ENGLISH?
<> = CHANGE
Make sure the cap is screwed on tightly, so that no detergent can get
into the container during the wash program (this could damage the
water softener beyond repair).
OK = YES
To select preferred language please
press button „<” or „>”.
Confirm by pressing „OK” button.
ENGLISH
SELECTED
After language confirmation, the appliance will go through the first
time use configuration menu.
2. Setting the water hardness
The water hardness is by default
set to level 3. To change water
hardness level press button „<” or „>”
repeatedly.
WATER HARDNESS
(1=MIN, 5=MAX)
WATER HARDNESS = 3
<> = CHANGE
OK = YES
To confirm your choice press „OK”
button. The level must be set
according to the table below.
To allow the water softener to work in a perfect way, it is essential that
the water hardness setting is based on the actual water hardness in your
house. This information can be obtained from your local water supplier.
Only use salt that has been specifically designed for dishwashers.
Whenever you need to add salt, it is mandatory to complete the
procedure before the beginning of the washing cycle.
Residual saline solution or grains of salt can lead to corrosion,
irreparably damaging the stainless steel components.
The guarantee is not applicable if faults are caused by such
circumstances.
If the salt container is not filled, the water softener and the
heating element may be damaged as a result.
4. Setting the brightness level
ADJUST BRIGHTNESS
(1=MIN, 5=MAX)
BRIGHTNESS = 5
<> = CHANGE
OK = YES
DETERGENT TYPE
German
degrees °dH
French
degrees °fH
0-6
0 - 10
1
Soft
2
Medium
7 - 11
11 - 20
3
Average
12 - 17
21 - 30
4
Hard
18 - 34
31 - 60
5
Very hard
35 - 50
61 - 90
3. Filling the water softener
POUR WATER
INSERT 1,5 LITER OF
OK = DONE
WATER IN THE
OK = DONE
WATER SOFTENER
OK = DONE
When water hardness is set, it is
required to fill water softener with
water and special regeneration salt.
Remove the lower rack and unscrew
the reservoir cap (anticlockwise)
To confirm Your choice press „OK”
button.
5. Detergent type operation
Water Hardness Table
Level
The brightness level is by default set
to level 5. To change brightness level
press button „<” or „>” repeatedly.
DO YOU USE
<> = NO
OK = YES
“ALL IN ONE”
<> = NO
OK = YES
DETERGENT?
<> = NO
OK = YES
In this step it is very important to
choose what type of detergent will
be used (tablet/capsule or
gel/powder).
If you prefer to use All-in-one
detergent in tablet or capsule for
washing - press „OK”, then go to
step 7. Open tap operation on the
next page.
The symbol
on display will be lit. If you prefer to use gel or
powder detergent for washing, press „<” or „>”, then go to step 6.
Rinse aid operation.
6. Rinse aid operation*
*If All-in-one detergent was chosen in the previous step, this step will
be skipped by the appliance.
RINSE AID
As a first step it is needed to fill
reservoir with water ( ~1.5 litres).
INSERT RINSE AID
OK = DONE
Once done, proceed to the next
step by pressing „OK” button.
IN THE DISPENSER
OK = DONE
INSERT SALT
ADD 1KG OF SALT
OK = DONE
35
25
IN THE SALT DISPENSER
OK = DONE
MA X
B
Position the funnel (see figure) and fill the salt reservoir right up to its
edge (approximately 1 kg); it is not unusual for some water will spill out.
Remove the funnel and wipe any salt residue away from the opening.
1.
2
A
EN
1. Open the dispenser B by pressing and pulling up the tab on the lid.
2. Carefully introduce the rinse aid as far as the maximum (110 ml) reference notch of the filling space A - avoid spilling it. If this happens,
clean the spill immediately with a dry cloth.
3. Press the lid down until you hear a click to close it.
4. Confirm operation by pressing „OK” button.
NEVER pour the rinse aid directly into the tub.
Setting rinse aid level
(not necessary when using tablets/capsules)
The rinse aid dosage can be adjusted to the detergent used. The lower
the setting, the less rinse aid is dispensed. The factory setting is for (5)
level.
To change, follow instructions in section “SETTINGS / MENU”.
8. First cycle operation
FIRST CYCLE
REMEMBER TO RUN THE
OK = DONE
INTENSIVE CYCLE
OK = DONE
WITH EMPTY BASKETS
OK = DONE
TO COMPLETE
OK = DONE
THE FIRST SET UP
OK = EXIT
Before normal use of appliance it is
recommended to run Intensive cycle first, to calibrate the appliance.
Insert a detergent into dispenser
chamber B (see below), then press
„OK” button.
Intensive cycle will be selected automaticly. Press „START”
button
and close the appliance door
within 4 sec.
This first cycle can be up to 20
minutes longer as a result of the
automatic calibration process.
After this process the appliance is ready for normal use.
7. Open tap operation
OPEN TAP
OPEN THE
OK = DONE
WATER TAP
OK = DONE
Check water tap is open. If closed, open it then confirm by pressing
„OK” button.
ADDING A DETERGENT
Only use detergent which has been specifically designed for
dishwashers.
To achieve the best washing and drying results, the combined use of
detergent, rinse aid liquid and refined salt is required.
We recommend using detergents that do not contain phosphates or
chlorine, as these products are harmful to the environment.
Good washing results also depend on the correct amount of detergent being used.
Exceeding the stated amount does not result in a more effective wash
and increases environmental pollution.
The amount can be adjusted to the soil level. In the case of normally
soiled items, use approximately either 35g (powder detergent) or
35ml (liquid detergent) and additional tea spoon of detergent directly
inside the tub. If tablets are used, one tablet will be enough.
If the crockery is only lightly soiled or if it has been rinsed with water
before being placed in the dishwasher, reduce the amount of detergent used accordingly (minimum 25 g/ml) e.g. skip the powder/gel
putted inside the tub.
To open the detergent dispenser,
press button A. Introduce the detergent into the dry dispenser B only.
Place the amount of detergent for
pre-washing directly inside the tub.
B
1. When measuring out the deterA
gent refer to the mentioned earlier information to add the proper
quantity. Inside the dispenser B
there are indications to help the
detergent dosing.
2. Remove detergent residues from the edges of the dispenser and
close the cover until it clicks.
3. Close the lid of the detergent dispenser by pulling it up until the
closing device is secured in place.
The detergent dispenser automatically opens up at the right time
according to the program.
If you are using a All-in-one detergents, we recommend that you add
salt in any case, especially if the water is hard or very hard (follow the
instructions given on the packaging).
3
EN
ADVICE AND TIPS
TIPS
Before loading the baskets, remove all food residues from the crockery
and empty the glasses. You do not need to rinse beforehand under
running water.
Arrange the crockery so that it is held in place firmly and does not tip
over; and arrange the containers with the openings facing downwards
and the concave/convex parts placed obliquely, thus allowing the
water to reach every surface and flow freely.
Warning: lids, handles, trays and frying pans do not prevent the sprayer arms from rotating.
Place any small items in the cutlery basket.
Very soiled dishes and pans should be placed in the lower basket
because in this sector the water sprays are stronger and allow a higher
washing performance.
After loading the appliance, make sure that the sprayer arms can
cotate freely.
HYGIENE
To avoid odour and sediment which can be accumulated in the dishwasher please run a high temperature program at least once a month.
Use a tea spoon of detergent and run it without the loading to clean
your appliance.
LOADING THE RACKS
CUTLERY RACK
The third rack was designed tohouse the cutlery.
Arrange the cutlery as shown in the figure.
A separate arrangement of the cutlery makes collection easier after
washing and improves washing and drying performance.
Knives and other utensils with sharp edges must be positioned
with the blades facing downwards.
The geometry of the rack makes it possible to place such small items
as coffee cups in the area in the middle.
The cutlery basket is equipped with two sliding side trays to make the
most of the height of the space below and enable the loading of high
items into upper rack.
4
UNSUITABLE CROCKERY
• Wooden crockery and cutlery.
• Delicate decorated glasses, artistic handicraft and antique crockery.
Their decorations are not resistant.
• Parts in synthetic material which do not withstand high temperatures.
• Copper and tin crockery.
• Crockery soiled with ash, wax, lubricating grease or ink.
The colours of glass decorations and aluminium/silver pieces can
change and fade during the washing process. Some types of glass (e.g.
crystal objects) can become opaque after a number of wash cycles
too.
DAMAGE TO GLASS AND CROCKERY
• Only use glasses and porcelain guaranteed by the manufacturer as
dishwasher safe.
• Use a delicate detergent suitable for crockery
• Collect glasses and cutlery from the dishwasher as soon as the wash
cycle is over.
EN
UPPER RACK
Load delicate and light dishes:
glasses, cups, saucers, low salad
bowls.
The upper rack has tip-up
supports which can be used in a
vertical position when arranging
tea/ dessert saucers or in a lower
position to load bowls and food
containers.
(loading example for the upper rack)
FOLDABLE FLAPS WITH ADJUSTABLE POSITION
The side foldable flaps can be positioned at three
different heights to optimize the arrangement of
crockery inside the rack.
Wine glasses can be placed safely in the foldable
flaps by inserting the stem of each glass into the
corresponding slots.
For optimum drying results incline the foldable flaps
more. To change the inclination, pull up the foldable
flap, slide it slightly and position it as you wish.
ADJUSTING THE HEIGHT OF THE UPPER RACK
The height of the upper rack can be adjusted: high position to place bulky crockery in
the lower basket and low position to make
the most of the tip-up supports by creating
more space upwards and avoid collision
with the items loaded into lower rack.
The upper rack is equipped with a Upper
Rack height adjuster (see figure), without pressing the levers, lift it up by simply
holding the rack sides, as soon as the rack is
stable in its upper position.
To restore to the lower position, press the
levers A at the sides of the rack and move the basket downwards.
We strongly recommend that you do not adjust the height of the
rack when it is loaded.
NEVER raise or lower the basket on one side only.
LOWER RACK
For pots, lids, plates, salad bowls, cutlery etc. Large plates and lids
should ideally be placed at the sides to avoid interferences with the
spray arm.
The lower rack has tip-up supports which can be used in a vertical
position when arranging plates or in a horizontal position (lower) to
load pans and salad bowls easily.
(loading example for the lower rack)
POWER CLEAN IN LOWER RACK
Power Clean® uses the special water jets
in the rear of cavity to wash more intensively the high dirty items.
Placing the pots/casseroles faced to the
Power Clean® component please activate the POWER CLEAN on the panel.
The lower rack has a Power Clean, a special pull-out support in the rear
of the rack that can be used to support frying pans or baking pans in
upright position, thus taking up less space.
How to use Power Clean®:
1. Adjust the Power Clean® area (G)
folding down the rear plate holders
to load pots.
2. Load pots and casseroles inclined
vertically in Power Clean® area. Pots
have to be inclined towards the
power water jets.
5
EN
SELECTING A CYCLE AND OPTIONS
The list of available cycles and options can be found in Cycle Table
on next page. Eco cycle is selected by default. If you want to have Last
Used cycle selected by default, you can change it in „Settings Menu”.
It is possible to select a cycle by pressing 1 of 6 cycles direct access
buttons or by pressing „Extra Cycles”
button repeatedly. When the
last one is reached a further press goes back to the first.
Press cycle button to choose cycle in accordance with the level
of soiling of the dishes and with Cycle Table. Information will be
shown on the display:
1
2
3
ECO CYCLE
5
4
Indicators
Name of the selected cycle
Vertical bar showing the position of the extra cycle list only
Energy consumption of the selected cycle
Water consumption of the selected cycle
1.
2.
3.
4.
5.
50°
3:40h
POWER
CLEAN
Three seconds after selecting a cycle, its
time and temperature will be displayed
(if available).
Press „INFO”
button to display a brief description of the cycle and
its water / energy consumption.
NORMALLY SOILED CROCKERY.
STANDARD PROGRAM,
During the selection phase the „START” LED
WATER
ENERGY
3:40h
POWER
CLEAN
If more than one option is selected one
bullet point for each option is displayed.
Each option name is displayed for 3 sec.
with its bullet point fulled.
When the cycle and option selection is complete, press „START”
button and close the door within 4 seconds to start chosen cycle.
6
TO PAUSE THE CYCLE (ADDING EXTRA ITEMS)
Open the door and place the crockery inside the dishwasher,
(beware of HOT steam!). Press „START”
button and close the
door within 4 sec. to resume the cycle from the point at which it was
interrupted.
ACCIDENTAL INTERRUPTIONS
If the door is opened during the wash cycle, or if there is a power
cut, the cycle stops. To resume the cycle from where it was interrupted, press the „START”
button and close the door within 4 sec.
After the cycle finishes, there is an acustic signal and the dispaly
shows:
CYCLE FINISHED
On the display additional information can be shown:
• ADD SALT - refill salt reservoir.
• ADD RINSE AID - refill rinse aid.
• DEGREASE AND CLEAN THE MACHINE WE RECOMMEND
TO USE WPRO - every 50 cycle, will be recommended to use
the WPRO cleaner (according to instruction on the consumable).
blinks.
Additional options are available for most cycles (see „Options and
Settings” section). When any option is selected, its name is shown on
the display on the right.
50°
MODIFYING A RUNNING PROGRAM
If a wrong program was selected, it is possible to change it, provided
that it has only just begun: open the door, press and hold the
„ON/OFF”
button, the machine will switch off.
Switch the machine back on using the „ON/OFF”
button and select the new wash cycle and any desired options;
start the cycle
by pressing the „START”
button and closing the door within 4 sec.
Open appliance door (beware of hot steam!) and unload the racks,
starting from the lower rack first.
If it is needed to refill salt reservoir or rinse aid dispenser, it is
recommended to do this operations right before start of the next
cycle.
After 10 minutes the appliance switches off.
EN
*
CYCLE
Available options
Detergent
dispenser
B
ECO
50°
SENSOR AUTO
50-60°
1H WASH
& DRY 55°
INTENSIVE
65°
EXPRESS 30’
50°
GLASS
45°
TUB
Duration of
wash cycle
(h:min)**
Water
Energy
consumption cosumption
(l/cycle)
(kWh/cycle)
TABLET, START DELAY, POWER CLEAN,
4:00
9.5
0.83
TABLET, START DELAY, MULTIZONE,
POWER CLEAN, TURBO
1:25 - 3:00
7.0 - 14.0
0.90 - 1.40
TABLET, START DELAY, MULTIZONE
-
1:00
10.5
1.20
TABLET, START DELAY, MULTIZONE,
POWER CLEAN, TURBO,
-
2:50
16.0
1.60
TABLET, START DELAY, MULTIZONE
-
0:30
9.0
0.55
TABLET, START DELAY, MULTIZONE
-
1:40
11.5
1.20
TABLET, START DELAY, MULTIZONE,
-
1:35
13.0
1.15
GOOD NIGHT 50°
TABLET, START DELAY,
-
3:30
15.0
1.15
PRE-WASH cold
START DELAY, MULTIZONE
-
0:12
4.5
0.01
EXTRA CYCLES - available by pressing
DAILY
HYGIENE
50°
Drying
phase
CYCLES TABLE
-
button
-
65°
START DELAY,
-
1:40
10.0
1.30
SELF CLEAN 65°
START DELAY,
-
0:50
8.0
0.85
-
-
1. ECO - Normally soiled crockery. standard program, the most efficient in terms of its combined energy and water consumption.
2. SENSOR AUTO - For normally soiled dishes with dried food residues. senses the level of soiling on the dishes and adjusts the program
accordingly.
3. 1H WASH & DRY - Light to normally soiled crockery. everyday program suitable for non-dried and fresh soiling, assuring clean and dried
4.
5.
6.
dishes in just 60 min of time.
INTENSIVE - Program recommended for heavily soiled crockery, especially suitable for pans and saucepans (not to be used for delicate items).
EXPRESS 30’ - Program to be used for lightly-soiled dishes with no dried food residues.
GLASS - Program for delicate items, which are more sensitive to high temperatures, for example glasses and cups.
EXTRA CYCLES
7. DAILY - Normally soiled crockery. everyday cycle, that ensures optimal cleaning performance in shorter time.
8. GOOD NIGHT - Suitable for night-time operation of the appliance. optimum performance ensured.
9. PREWASH - Crockery to be washed later. no detergent to be used with this program.
10. HYGIENE - Normally or heavily soiled crockery, with additional antibacterial wash.
11. SELF CLEAN - Program to be used to perform maintenance of the dishwasher. it cleans the interior of the appliance using hot water.
Notes:
Please note that cycles like “1h Wash & Dry” or “Express” are most effective for lightly soiled dishes.
To reduce consumption even further, only run the dishwasher when it is full.
ECO program data is measured under laboratory conditions according to European Standard EN 50242. Note for Test Laboratories: For information on
comparative EN testing conditions, please send an email to the following address: dw_test_support@whirlpool.com
Pre-treatment of the dishes is not needed before any of the programs.
*) Not all options can be used simultaneously.
**) The duration of the program shown on the display or in the booklet is an estimate calculated on standard conditions. The actual time may vary
depending on many factors such as temperature and pressure of the incoming water, room temperature, amount of detergent, quantity and type of load,
load balancing, additional selected options and sensor calibration. The sensor calibration can increase program duration up to 20 min.
Standby consumption: Left-on mode consumption: 5 W - Off mode consumption: 0.5 W
7
EN
OPTIONS AND SETTINGS
With each cycle additional options can be used. A full list of available options working with specific cycles can be found in the Cycle Table on
the previous page. All active options are shown on the display.
To set an option press „OK” button. SET OPTIONS message is shown for a few seconds. Then use „<” or „>” button to navigate through the
option list. Press „OK” to select the option, in the setting menu the LED above „OK” button is lit.
If the option is not available, it will be still visible in its position but with „
TABLET (All-in-one)
POWER CLEAN
This setting allows you to optimise the performance of the cycle
according to the type of detergent used. Enable it if you use combined
detergents in tablet form (rinse aid, salt and detergent in 1 dose).
TABLET
OFF
TABLET
ON
TABLET
ON
To set the Tablet, enter in the setting
menu by pressing „OK” button and
navigate with „< , >” until „TABLET”
is shown, then press „OK” button.
The start of the cycle may be delayed for a selected period of time.
To set a delay, enter in the setting menu by pressing „OK” button and navigate with „< , >” until „START DELAY” is shown, then press „OK” button.
With each press of the button “>” or “<“, the delay start increases by:
• every 0:30 if selection below 4 hours,
• every 1:00 if selection is below 12 hours,
• every 2 hours if selection is above 12 hours.
START DELAY
OFF
To remove the delay, press „<” or „>”
button until „OFF” is displayed.
<STARTS IN h>
OFF
Default value is OFF.
<STARTS IN h>
4:00
<STARTS IN h>
4:00
If delay is selected, the is lit
Once „OK” button is pressed the
delay is confirmed and the machine
comes back to the cycle selection
screen with delay value visible.
Press „START” and close the door within 4 sec. to start the delay
MULTIZONE
If there are not many dishes to be washed it can be loaded in one rack
only. Using this option you can select which rack you want to wash.
To set the Multizone, enter in the setting menu by pressing „OK”
button and navigate with „< , >” until „MULTIZONE” is shown, then
press „OK” button.
MULTIZONE
OK
<ALL RACKS>
<>
By default the MULTIZONE is not
active and all racks icons are lit.
<LOW ONLY>
<>
The multizone icon becomes lit.
<HIGH ONLY>
<>
The multizone icon becomes lit.
<CUTLERY ONLY>
<>
The multizone icon becomes lit.
8
Thanks to additional water jets this option provides a more intensive
and powerful wash in the specific area of lower rack.
POWER CLEAN
OFF
POWER CLEAN
ON
POWER CLEAN
ON
Default value is OFF.
To set the Power Clean, enter in
the setting menu by pressing „OK
button and navigate with „< , >”
until „POWER CLEAN” is shown,
then press „OK” button.
TURBO
START DELAY
<CUTLERY ONLY>
”
This option can be used to reduce the duration of the main cycles
while maintaining washing and drying performance levels.
TURBO
OFF
TURBO
ON
TURBO
ON
To set the Turbo, enter in the setting
menu by pressing „OK” button and
navigate with „< , >” until „TURBO” is
shown, then press „OK” button.
With each press of the button „>”
or „<“ option will be ON or OFF.
Confirm by pressing „OK” button.
FLOOR LIGHT
A LED light projected on the floor indicates that the dishwasher is
working. The light stays on during the cycle and switches off at the
end of the cycle.
This feature is active by default, but it is possible to deactivate it in the
“SETTINGS MENU”.
TUB LIGHT
When the feature is active the LEDs in the tub are automatically switched on/off as soon as the user open/close the door respectively.
If the door remains opened for more than 10 min, the LEDs in the
tub switch off (to turn them on again, the door has to be closed and
opened again).This feature is active by default, but it is possible to
deactivate it in the “SETTINGS MENU”.
EN
SETTINGS MENU
To change machne settings you need to enter into the Settins Menu.
Press „OK” button and navigate with „< , >” until SETTINGS is shown, then press „OK” button.
To exit the setting menu, press any cycle button or press „< , >” button untill EXIT is shown, then press „OK” button.
Language
Tub Light
1.LANGUAGE
OK
1.ENGLISH
<>
To change language, enter in the
setting menu by pressing „OK”
button and navigate with „< , >”
until „LANGUAGE” is shown, then
press „OK” button.
1.ITALIAN
7.TUB LIGHT
ON
7.TUB LIGHT
OFF
To change tub light, enter in the
setting menu by pressing „OK”
button and navigate with „< , >”
until „TUB LIGHT” is shown, then
press „OK” button.
Rinse Aid level
First cycle
2.FIRST CYCLE
OK
2.<ECO>
<>
You can choose which cycle is
selected by default when switching
on the appliance: ECO or the LAST
USED one.
To change first cycle, enter in the
setting menu by pressing „OK” button and navigate with „< , >” until
„FIRST CYCLE” is shown, then press
„OK” button.
2.<LAST USED>
Sounds
3.SOUNDS
OK
3.<HIGHT>
<>
To change sounds, enter in the
setting menu by pressing „OK”
button and navigate with „< , >”
until „SOUNDS” is shown, then press
„OK” button.
3.<OFF>
Choose between 2 levels: High;
Low. Can be also OFF.
8.RINSE AID LEV.
5
8.RINSE AID LEV.
4
To change rinse aid level, enter in
the setting menu by pressing „OK”
button and navigate with „< , >”
until „RINSE AID LEV.” is shown, then
press „OK” button.
Choose between five levels: 1, 2, 3, 4 and 5.
If the rinse aid level is set to 1, no rinse aid will be supplied. The LOW
RINSE AID indicator light will not be lit if you run out of rinse aid.
The factory setting is for (5) level .
• If you see bluish streaks on the dishes, set a low number (2-3).
• If there are drops of water or limescale marks on the dishes, set
a high number (4-5).
Demo mode
8.DEMO MODE
ON
8.DEMO MODE
OFF
To see to demo mode, enter in the
setting menu by pressing „OK”
button and navigate with „< , >”
until „DEMO MODE” is shown, then
press „OK” button.
Reset to factory default
Water Hardness
4.WATER HARDNESS
3
4.WATER HARDNESS
4
To change water hardness level,
enter in the setting menu by
pressing „OK” button and navigate
with „< , >” until „WATER HARDNESS”
is shown, then press „OK” button.
To setup correct level according to water hardness, see table on page 2.
Screen Brightness
5.SCREEN BRIGHT.
5
5.SCREEN BRIGHT.
3
To change screen brightness
level, enter in the setting menu by
pressing „OK” button and navigate
with „< , >” until „SCREEN BRIGHT.” is
shown, then press „OK” button.
9.RESET TO DEF.
ON
9.RESET TO DEF.
OFF
To reset to factory default, enter in
the setting menu by pressing „OK”
button and navigate with „< , >”
until „RESET TO DEF.” is shown, then
press „OK” button.
Exit
10.EXIT
< >
To exit the setting menu, press any
cycle button or press „< , >” button
untill EXIT is shown, then press„OK”
button.
Choose between five levels: 1, 2, 3, 4 and 5.
Floor Light
6.FLOOR LIGHT
ON
6.FLOOR LIGHT
OFF
To change floor light, enter in the
setting menu by pressing „OK”
button and navigate with „< , >”
until „FLOOR LIGHT” is shown, then
press „OK” button.
9
EN
CARE AND MAINTENANCE
ATTENTION: Always unplug the appliance when cleaning it and when
performing maintenance work. Do not use flammable liquids to clean
the machine.
CLEANING THE DISHWASHER
Any marks on the inside of the appliance may be
removed using a cloth dampened with water and a
little vinegar.
The external surfaces of the machine and the control
panel can be cleaned using a non-abrasive cloth
which has been dampened with water. Do not use
solvents or abrasive products.
After several washes, check the filter assembly and if necessary clean
it thoroughly under running water, using a non-metallic brush and
following the instructions below:
1. 1. Turn the cylindrical filter A in an anti-clockwise direction and pull
it out (Fig 1).
2. Remove the cup filter B by exerting a slight pressure on the side
flaps (Fig 2).
3. Slide out the stainless-steel plate filter C (Fig 3).
4. Inspect the trap and remove any food residues. NEVER REMOVE
the wash-cycle pump protection (black detail) (Fig 4).
1
2
PREVENTING UNPLEASANT ODOURS
Always keep the door of the appliance ajar in order to avoid moisture
from forming and being trapped inside the machine.
Clean the seals around the door and detergent dispensers regularly
using a damp sponge. This will avoid food becoming trapped in the seals, which is the main cause behind the formation of unpleasant odours.
B
A
A
CHEKING THE WATER SUPPLY HOSE
Check the inlet hose regularly for brittleness and cracks. If damaged,
replace it by a new hose available through our After-Sales Service or
your specialist dealer. Depending on the hose type:
C
3
If the inlet hose has a transparent coating, periodically check if the
colour intensifies locally. If yes, the hose may have a leak and should
be replaced.
For water stop hoses: check the small safety valve inspection window
(see arrow). If it is red, the water stop function was triggered, and the
hose must be replaced by a new one.
For unscrewing this hose, press the release button while unscrewing
the hose.
CLEANING THE WATER INLET HOSE
If the water hoses are new or have not been used for an extended
period of time, let the water run to make sure it is clear and free of impurities before performing the necessary connections. If this precaution is not taken, the water inlet could become blocked and damage
the dishwasher.
CLEANING THE FILTER ASSEMBLY
Regularly clean the filter assembly so that the filters do not clog and
that the waste water flows away correctly.
The filter assembly consists of three filters which remove food residues
from the washing water and then recirculate the water: to obtain the
best washing results, you need to keep them clean.
The dishwasher must not be used without filters or if the filter is
loose.
10
4
After cleaning the filters, re-place the filter assembly and fix it in position correctly; this is essential for maintaining the efficient operation
of the dishwasher.
CLEANING THE SPRAY ARMS
On occasions, food residue may
become encrusted onto the spray
arms and block the holes used
to spray the water. It is therefore
recommended that you check the
arms from time to time and clean
them with a small non-metallic
brush.
To remove the upper spray arm,
turn the plastic locking ring in an
anti-clockwise direction. The upper
spray arm should be replaced so that the side with the greater number
of holes is facing upwards.
The lower spray arm may be removed by pulling it upwards.
EN
INSTALLATION
ATTENTION: If the appliance must be moved at any time, keep it in an
upright position; if absolutely necessary, it may be tilted onto its back.
ELECTRICAL CONNECTION
WARNING: Under no circumstances should the water inlet hose
be cut as it contains live electrical parts.
CONNECTING THE WATER SUPPLY
Before inserting the plug into the electrical socket, make sure that:
CONNECTING THE WATER INLET HOSE
• The socket is earth and complies with current regulations;
• The socket can withstand the maximum load of the appliance as
shown on the data plate located on the inside of the door (see
PRODUCT DESCRIPTION).
• The power supply voltage falls within the values indicated on the
data plate on the inside of the door.
• The socket is compatible with the plug of the appliance.
Adaptation of the water supply for installation should only be performed by a qualified technician.
The water inlet and outlet hoses may be positioned towards the right
or the left in order to achieve the best possible installation.
Make sure the dishwasher does not bend or squash the hoses.
• Run the water until it is perfectly clear.
• Screw the inlet hose tightly into position and turn on the tap.
If the inlet hose is not long enough, contact a specialist store or an
authorised technician.
The water pressure must be within the values indicated in the Technical Data table - otherwise the dishwasher may be function properly.
Make sure the hose is not bent or compressed.
SPECIFICATIONS FOR THE CONNECTION OF THE WATER SUPPLY HOSE:
WATER SUPPLY
cold or hot (max. 60°C)
WATER INTAKE
3/4”
POWER OF WATER PRESSURE
0,05 ÷ 1 MPa (0.5 ÷ 10 bar)
7,25 – 145 psi
CONNECTING THE WATER OUTLET HOSE
Connect the outlet hose to a drain duct with a minimum diameter of
2 cm A.
The outlet hose connection must be at a height ranging from 40 to
80 cm from the floor or surface where the dishwasher rests.
Before connecting the water outlet hose to the sink drain, remove the
plastic plug B.
ANTI-FLOODING PROTECTION
Anti-flooding protection. To ensure floods do not occur, the dishwasher:
- is provided with a special system which blocks the water supply in
the event of anomalies or leaks from inside the appliance.
Some models are also equipped with the supplementary safety device
New Aqua Stop, which guarantees anti-flooding protection even in
the event of a supply hose rupture.
Under no circumstances should the water inlet hose be cut as it contains live electrical parts.
MAX 80 cm
If this is not the case, ask an authorised technician to replace the plug
(see AFTER-SALES SERVICE). Do not use extension cables or multiple
sockets. Once the appliance has been installed, the power supply
cable and the electrical socket should be easily accessible.
The cable should not be bent or compressed.
If the power supply cable is damaged, have it replaced by the manufacturer or its authorised Technical Assistance Service in order to
prevent all potential hazards.
The Company shall not be held responsible for any incidents, if these
regulations are not observed.
POSITIONING AND LEVELLING
1. Position the dishwasher on a level sturdy floor. If the floor is uneven,
the front feet of the appliance may be adjusted until it reaches
a horizontal position. If the appliance is levelled correctly, it will be
more stable and much less likely to move or cause vibrations and
noise while it is operating.
2. Before recessing the dishwasher, stick the adhesive transparent strip
under the wooden shelf in order to protect it from any condensation
which may form.
3. Place the dishwasher so that its sides or back panel are in contact
with the adjacent cabinets or the wall. This appliance can also be
recessed under a single worktop.
4. To adjust the height of the rear foot, turn the red hexagonal bushing
on the lower central part at the front of the dishwasher using a
hexagonal spanner with an opening of 8 mm. Turn the spanner in
a clockwise direction to increase the height and in an anticlockwise
direction to decrease it.
DIMENSIONS AND CAPACITY:
WIDTH
598 mm
HEIGHT
820 mm
DEPTH
555 mm
CAPACITY
14 standard place-settings
MIN 40 cm
11
EN
TROUBLESHOOTING
Your dishwasher may not work properly.
Before contacting the After-sales Service, check if the problem can be solved by going through the following list.
PROBLEMS
Display shows:
CHECK SALT or
ADD SALT
POSSIBLE CAUSES
SOLUTIONS
Salt reservoir is empty.
Refill reservoir with salt (see page 2).
Adjust water hardness (see page 2).
Rinse aid dispenser is empty.
Refill dispenser with rinse aid (see page 2).
Display shows:
CHECK RINSE AID or
ADD RINSE AID
The appliance must be switched on. Check the household circuit fuse if there is no power supply.
The appliance door doesn’t close.
Check if the appliance door is closed.
“Start Delay” option is ON.
Check whether the „Start Delay” option has been selected. If it has, the
appliance will start once the set time has elapsed. If necessary, Reset
the current cycle by switching OFF the dishwasher, then switch it on
again, select a new cycle, press START and close the door within 4 sec.
Water pressure is too low.
The water tap must be fully open during water inlet (minimum capacity: 0.5 litres per minute).
Kinked water inlet hose or cloged
inlet filters.
The water inlet hose must not be kinked and the inlet filter in the water
tap connector must not be dirty or clogged.
Dirty filters.
Clean the filters.
Kinked drain hose.
The drain hose must not be kinked.
Syphon hose connection closed.
The closure disk of the syphon hose connection
must be removed.
Dirty filters or spray arms.
Clean filters and spray arms.
Too little water in the appliance
system.
Concave items (e.g. bowls, cups) must be arranged
facing downwards in the rack.
Drain hose incorrectly fitted.
The drain hose must be fitted correctly (for high mounted appliances,
leave min. 200 - 400mm from the lower edge of the appliance) - see
Installation.
High level of foam inside.
Repeat without detergent or wait until foam
disappears.
Water pressure is too low.
The water tap must be fully open during water inlet (minimum capacity: 0.5 litres per minute).
Kinked water inlet hose or cloged
inlet filters.
The water inlet hose must not be kinked and the inlet filter in the water
tap connector must not be dirty or clogged.
Display shows:
Door is not closed within
4 seconds of button press.
Press again and close the appliance door within 4 seconds.
Display shows:
The door was not open between
cycles.
Unload appliance (if not unloaded before), open and close the door.
Display shows: Fx
Appliance has technical defect.
Call customer service (state fault displayed).
Close the water tap.
... is not working / will not
start.
Display shows: F6
symbol on the display
indicators
Display shows: F3
Display shows: F2
PRESS START AND
CLOSE THE DOOR
OPEN AND CLOSE
THE DOOR
12
EN
PROBLEMS
POSSIBLE CAUSES
SOLUTIONS
The door doesn’t
lock.
Racks are not fit to the end.
Verify that racks are fit to the end.
The door is not lock.
Vigorously push the door until you hear the “clack” sound.
The dishes are rattling against each.
Arrange the crockery correctly (see Loading the Racks).
An excessive amount of foam has been
produced.
The detergent has not been measured out correctly or it is not suitable for
use in dishwashers (see Filling the Detergent Dispenser). Reset the current
cycle by switching OFF the dishwasher, then switch it on again, select a
new program, press START and close the door within 4 sec. Please do not
add any detergent.
The selected program hasn’t any drying
phase.
Verify on the programs table if the selected program has the drying phase.
The rinse aid has run out or the resolution
is not adequate.
Add the rinse aid or adjust the dosage levels higher (see Filling the Rinse
Aid Dispenser).
The dishes are made of non-stick or
plastic.
It is normal the presence of drops of water (see Tips).
The crockery has not been arranged
properly.
Arrange the crockery correctly (see Loading the Racks).
The spray arms cannot rotate freely, being
hindered by the dishes.
Arrange the crockery correctly (see Loading the Racks).
The wash cycle is too gentle and/or detergent efficiency is low.
Select an appropriate wash cycle (see Programs Table).
An excessive amount of foam has been
produced (see AFTER-SALES SERVICE).
The detergent has not been measured out correctly or it is not suitable for
use in dishwashers (see Filling the Detergent Dispenser). Reset the current
cycle by switching OFF the dishwasher, then switch it on again, select a
new program, press START and close the door within 4 sec. Please do not
add any detergent.
The dishwasher
makes excessive
noise.
The dishes have not
been dried.
The dishes are not
clean.
The cap on the rinse aid compartment has
Make sure the cap of the rinse aid dispenser is closed.
not been shut correctly.
The filter is soiled or clogged.
Clean the filter assembly (see Care and Maintenance).
There is no salt.
Fill the salt reservoir (see Filling the Salt Reservoir).
The salt level is too low.
Fill the salt reservoir (see Filling the Salt Reservoir).
The adjustment of the water hardness is
The dishes and glas- not adequate.
ses show calcination The cap of the salt reservoir is not properor a whitish film.
ly closed.
The dishes and
glasses are blue
streaked or have a
bluish tinge.
Increase the values (see Water Hardness Table).
Check to have properly closed the salt reservoir cap.
The rinse aid is used up or the dosage is
insufficient.
Add the rinse aid or adjust the dosage levels higher.
The rinse aid dosage is excessive.
Adjust the dosage rates below.
PRODUCT FISCHE
The technical data containing the energy consumption data can be
downloaded from the website: docs.bauknecht.eu
400011311510
CONTACTING AFTER-SALES SERVICE
You can find our contact details in the warranty manual. When contacting our Client
After-sales Service, please state the codes
provided on your product’s rating plate.
IEC 436
:
10/2018 jk - Xerox Fabriano
13
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising