Hotpoint | WDD 740 P (UK) | Instruction for Use | Hotpoint WDD 740 P (UK) Instruction for Use

Hotpoint WDD 740 P (UK) Instruction for Use
Instructions for use
WASHER DRYER
Contents
GB
English,1
GB
Installation, 2-3-4-5
Unpacking and levelling
Connecting the electricity and water supplies
The first wash cycle
Technical data
Description of the washer dryer, 6-7
Control panel
Display
How to run a wash cycle or a drying cycle, 8
Wash cycles and functions, 9
Table of wash cycles
Wash functions
WDD 740 P/G/A/K
Detergents and laundry, 10
Detergent dispenser drawer
Preparing the laundry
Garments requiring special care
Load balancing system
Precautions and tips, 11
General safety
Disposal
Opening the porthole door manually
Care and maintenance, 12
Cutting off the water or electricity supply
Cleaning the washer dryer
Cleaning the detergent dispenser drawer
Caring for the door and drum of your appliance
Cleaning the pump
Checking the water inlet hose
Troubleshooting, 13
Assistance, 14
Installation
GB
! Keep this instruction manual in a safe place for
future reference. Should the appliance be sold,
transferred or moved, make sure the instruction
manual accompanies the Washer-dryer to inform
the new owner as to its operation and features.
! Read these instructions carefully: they contain
vital information on installation, use and safety.
Unpacking and levelling
Levelling your appliance correctly will provide it with
stability and avoid any vibrations, noise and shifting
during operation. If it is placed on a fitted or loose
carpet, adjust the feet in such a way as to allow
enough room for ventilation beneath the Washerdryer.
Electric and water connections
Connecting the water inlet hose
Unpacking
1. Unpack the Washer-dryer.
2. Check whether the Washer-dryer has been
damaged during transport. If this is the case, do
not install it and contact your retailer.
3. Remove the 4
protective screws and
the rubber bush with
the respective spacer,
situated on the rear of
the appliance (see also
the installation leaflet).
NB:The plastic spacers
may fall down inside the
machine once the bolt
has been removed, and will not interfere with the
operation of the machine.
4. Do not remove external bar.
5. Seal the gaps using the plastic plugs provided.
6. Keep all the parts: you will need them again if
the Washer-dryer needs to be moved to another
location.
! Packaging materials are not children's toys.
Levelling
Your machine may make a considerable amount of
noise if the two front feet have not been adjusted
correctly.
1. Install the Washer-dryer on a flat sturdy floor,
without resting it up against walls, furniture
cabinets or other.
2. If the floor is not
perfectly level, compensate for any
unevenness by
tightening or loosening
the adjustable front
feet (see figure); the
angle of inclination,
measured according to
the worktop, must not
exceed 2°.
A
1. Insert seal A into the
end of the inlet hose and
screw the latter onto a
cold water tap with a 3/4
gas threaded mouth
(see figure).
Before making the
connection, allow the
water to run freely until
it is perfectly clear.
2. Connect the other end
of the water inlet hose to
the Washer-dryer,
screwing it onto the
appliance's cold water
inlet, situated on the top
right-hand side on the
rear of the appliance (see
figure).
3. Make sure there are no kinks or bends in the
hose.
! The water pressure at the tap must be within the
values indicated in the Technical details table
(on the next page).
! If the water inlet hose is not long enough, contact
a specialist store or an authorised serviceman.
! Ensure that the supply taps are allowing water
through. Old taps may seize in the closed position
and thus prevent water reaching the machine.
Connecting the drain hose
65 - 100 cm
Connect the drain
hose, without bending
it, to a draining duct or
a wall drain situated
between 65 and 100 cm
from the floor;
_ the supply voltage is included within the values
indicated on the Technical details table
(see page 5);
GB
_ the socket is compatible with the washing
machine's plug. If this is not the case, replace
the socket or the plug.
Your appliance is now supplied with a 13 amp fused
plug it can be plugged into a 13 amp socket for
immediate use. Before using the appliance please
read the instructions below.
The drain hose may be
connected to an undersink trap. Before
connecting the drain
hose from the machine
ensure that any blanks
or removable ends have
been taken off the
spigot.
If it is place over the
edge of a basin or sink
be sure the free end
of the hose should not
be underwater.
! We advise against the use of hose extensions; in
case of absolute need, the extension must have
the same diameter as the original hose and must
not exceed 150 cm in length.
Ensure that if the drain hose is pushed into a
standpipe, that the end does not go down more
than 15cms (6 inches). If the hose is pushed down
too far, this may cause the machine to self syphon ie. continuously empty as it is filling.
Electric
connection
Before plugging the appliance into the mains
socket, make sure that:
_ the socket is earthed and in compliance with
the applicable law;
_ the socket is able to sustain the appliance's
maximum power load indicated in the Technical
details table (see page 5);
WARNING - THIS APPLIANCE MUST BE EARTHED.
THE FOLLOWING OPERATIONS SHOULD BE CARRIED
OUT BY A QUALIFIED ELECTRICIAN.
Replacing the fuse:
When replacing a faulty fuse, a 13 amp ASTA
approved fuse to BS 1362 should always be used,
and the fuse cover re-fitted. If the fuse cover is
lost, the plug must not be used until a replacement
is obtained.
Replacement fuse covers:
If a replacement fuse cover is fitted, it must be of
the correct colour as indicated by the coloured
marking or the colour that is embossed in words on
the base of the plug. Replacements can be obtained
directly from your nearest Service Depot.
Removing the plug:
If your appliance has a non-rewireable moulded plug
and you should wish to re-route the mains cable
through partitions, units etc., please ensure that
either:
the plug is replaced by a fused 13 ampere rewearable plug bearing the BSI mark of approval.
or:
the mains cable is wired directly into a 13 amp cable
outlet, controlled by a switch, (in compliance with
BS 5733) which is accessible without moving the
appliance.
Disposing of the plug:
Ensure that before disposing of the plug itself, you
make the pins unusable so that it cannot be
accidentally inserted into a socket.
Instructions for connecting cable to an alternative
plug:
Important: the wires in the mains lead are coloured
in accordance with the following code:
Green & Yellow E a r t h
Blue
Neutral
Brown
Live
!
GB
As the colours of the wires in the lead may not
correspond with the coloured markings identifyng
the terminals in your plug, proceed as follows:
Connect Green & Yellow wire to terminal marked E
or coloured Green or Green & Yellow.
or
Connect Brown wire to terminal marked L or
coloured Red.
Connect Blue wire to terminal marked N or coloured
Black.
If a 13 amp plug (BS 1363) is used it must be fitted
with a
13 amp fuse, either in the plug or adaptor or at the
distribution board.
If you are in any doubt the electrical supply to your
machine, consult a qualified electrician before use.
How to connect an alternative plug:
The wires in this mains lead are coloured in
accordance with the following code:
BLUE
NEUTRAL (N)
BROWN
LIVE (L)
GREEN & YELLOW
EARTH (E)
Disposing of the appliance:
When disposing of the appliance please remove the
plug by cutting the mains cable as close as possible to
the plug body and dispose of it as described above.
GREEN &
YELLOW
BROWN
BLUE
13 ampere fuse
CROSS-BAR
CORD GRIP
! The Washer-dryer should not be installed in an
outdoor environment, not even when the area is
sheltered, because it may be very dangerous to
leave it exposed to rain and thunderstorms.
! When the Washer-dryer is installed, the mains
socket must be within easy reach.
! Do not use extensions or multiple sockets.
! The power supply cable must never be bent or
dangerously compressed.
! The power supply cable must only be replaced by
an authorised serviceman.
"
Warning! The company denies all liability if and when
these norms are not respected.
The first wash cycle
Once the appliance has been installed, and before
you use it for the first time, run a wash cycle with
.
detergent and no laundry, using the wash cycle
GB
Technical data
Model
WDD 740 P/G/A/K
Dimensions
width 59.5 cm
height 85 cm
depth 53,5 cm
Capacity
from 1 to 7 kg for the wash programme;
from 1 to 5 kg for the drying programme
Electrical
connections
please refer to the technical data plate
fixed to the machine
Water
connections
maximum pressure 1 MPa (10 bar)
minimum pressure 0.05 MPa (0.5 bar)
drum capacity 52 litres
Spin speed
up to 1400 rotations per minute
Energy
rated
programmes
according to
regulation
EN 50229
Wash: programme
(1st press of the
button); temperature 60°C;
using a load of 7 kg.
Drying: first drying cycle performed with a
2 kg load, by selecting the "IRON DRY"
dryness level;
The second drying cycle is performed with
a 5 kg load, by selecting the "CUPBORD
DRY" dryness level.
This appliance conforms to the following
EC Directives:
- 89/336/EEC dated 03/05/89
(Electromagnetic Compatibility) and
subsequent modifications
- 2002/96/EC
- 2006/95/EC (Low Voltage)
#
Description of the washer dryer
GB
Control panel
CHILD
LOCK button
ON/OFF
DRYING
button
button
SPIN
button
SPEED
D I S P L AY
Detergent dispenser
drawer
MEMORY
WA S H
CYCLE
SELECTOR
buttons
Detergent dispenser drawer: used to dispense
detergents and washing additives (see “Detergents
and laundry”).
ON/OFF button : press this briefly to switch the
machine on or off. The START/PAUSE indicator light,
which flashes slowly in a green colour shows that
the machine is switched on. To switch off the
washer dryer during the wash cycle, press and hold
the button for approximately 2 seconds; if the
button is pressed briefly or accidentally the
machine will not switch off. If the machine is
switched off during a wash cycle, this wash cycle
will be cancelled.
WASH CYCLE SELECTOR buttons: used to set
the desired wash cycle (see "Table of wash cycles").
MEMORY button: press and hold the button to
store a cycle with your own set of preferences in
the memory of the machine. To recall a previously
stored cycle, press the MEMO button.
FUNCTION buttons: press the button to select
the desired function. The corresponding indicator
light on the display will switch on.
: press to reduce or completely
SPIN button
exclude the spin cycle - the value is indicated on the
display.
$
button
FUNCTION
buttons
DEL AYED
START button
S TA R T/
PA U S E
button with
indicator light
T E M P E R AT U R E
button
: press to decrease the
TEMPERATURE button
temperature: the value will be shown on the display.
CHILD LOCK button: to activate the control panel
lock, press and hold the button for approximately 2
seconds. When the symbol is illuminated, the
control panel is locked. This means it is possible to
prevent wash cycles from being modified
accidentally, especially where there are children in
the home. To deactivate the control panel lock,
press and hold the button for approximately 2
seconds.
: press to set a delayed
DELAY START button
start time for the selected wash cycle. The delay
time will be shown on the display.
DRYING button
: press to set a drying cycle.
START/PAUSE button with indicator light: when
the green indicator light flashes slowly, press the
button to start a wash cycle. Once the cycle has
begun the indicator light will remain lit in a fixed
manner. To pause the wash cycle, press the button
again; the indicator light will flash in an orange
is not illuminated, the door
colour. If the symbol
may be opened. To start the wash cycle from the
point at which it was interrupted, press the button
again.
Display
GB
*
)
,
+
-
.
The display is useful when programming the machine and provides a great deal of information.
The upper two strings A and B are used to display the selected wash cycle or the type of drying selected, the
current wash cycle phase (the selected dryness level or drying time) and all the indications relating to the
progress status of the cycle.
String C shows the time remaining until the end of the wash cycle in progress and, if a DELAYED START has
been set, the time remaining until the start of the selected wash cycle.
String D shows the maximum spin speed value (this depends on the selected wash cycle); if the wash cycle
does not include a spin cycle, the string remains unused.
String E shows the maximum temperature value which may be selected (this depends on the wash cycle used);
if the temperature of the wash cycle cannot be modified, the string remains unused.
Indicator lights F correspond to the functions and light up when the selected function is compatible with the
set wash cycle.
Door locked symbol
If the symbol is lit, this indicates that the washer dryer door is blocked to prevent it from being opened
accidentally. To prevent any damage from occurring, wait for the symbol to switch itself off before opening
the appliance door.
N.B.: if the DELAYED START function has been activated, the door cannot be opened; pauses the machine by
pressing the START/PAUSE button if you wish to open it.
The first time the machine is switched on, you will be asked to select the language and the display will
automatically show the language selection menu.
To select the desired language press the TEMPERATURE and SPIN buttons; to confirm the selection press the
DRYING button.
If you wish to select another language, press and hold the DRYING + TEMPERATURE + SPIN buttons
simultaneously for 5 seconds, then repeat the steps listed above.
%
How to run a wash cycle or a drying
cycle
GB
1. SWITCH THE MACHINE ON. Press the
button; the
text HELLO will appear on the display and the START/
PAUSE indicator light will flash slowly in a green colour.
2. LOAD THE LAUNDRY. Open the porthole door. Load
the laundry, making sure you do not exceed the
maximum load value indicated in the table of
programmes on the following page.
3. MEASURE OUT THE DETERGENT. Pull out the
detergent dispenser drawer and pour the detergent
into the relevant compartments as described in
"Detergents and laundry".
4. CLOSE THE DOOR.
5. SELECT THE WASH CYCLE. Press one of the
WASH CYCLE SELECTOR buttons to select the
required wash cycle; the name of the wash cycle will
appear on the display. A temperature and spin speed
is set for each wash cycle; these may be adjusted.
The duration of the cycle will appear on the display.
6. CUSTOMISE THE WASH CYCLE. Use the relevant
buttons:
Modifying the temperature and/or
spin speed. The machine automatically selects the
maximum temperature and spin speed set for the
selected wash cycle; these values cannot therefore be
increased. The temperature can be decreased by
button, until the cold wash "OFF" setting
pressing the
is reached. The spin speed may be progressively
button, until it is completely
reduced by pressing the
excluded (the "OFF" setting). If these buttons are
pressed again, the maximum values are restored.
Setting a delayed start.
To set a delayed start for the selected programme,
press the corresponding button repeatedly until the
required delay period has been reached. When this
symbol lights up on the
option is enabled, the
display. To remove the delayed start function press
the button until the text "OFF" appears on the display.
Setting the drying cycle.
The desired drying cycle type may be set by pressing
the DRYING button once or several times. Two
options are available:
A - Based on the how damp the clothes are once they
have been dried:
Iron dry: slightly damp clothes, easy to iron.
Hanger dry: dry clothes to put away.
Cupboard dry: very dry clothes, recommended for
towelling and bathrobes.
B - Based on time: from 40 minutes to 180.
To exclude the drying phase press the relevant button
until the text OFF appears on the display.
If your laundry load to be washed and dried is much
greater than the maximum stated load (see adjacent
table), perform the wash cycle, and when the cycle is
complete, divide the garments into groups and put
some of them back in the drum. At this point, follow
the instructions provided for a "Drying only" cycle.
Repeat this procedure for the remainder of the load.
N.B: a cooling-down period is always added to the
end of each drying cycle.
&
Drying only
) using the WASH
Select a drying setting (
CYCLE selector in accordance with the type of fabric, then
select the desired drying type using the DRYING button.
6able of Drying times
Fabric
type
Load type
Cotton
Clothing of different
sizes, Terry towels
(guideline values)
Synthe- Sheets, Shirts, Pyjamas,
tics
socks, etc.
Wool
Knitwear, Pullovers, etc.
Max. Cupboard
load dry
(kg)
Henger Iron
dry
dry
5
180
170
160
3
180
170
160
1,5
150
140
130
Modifying the cycle settings.
• Press the button to enable the function; the
indicator light corresponding to the button will
switch on.
• Press the button again to disable the function; the
indicator light will switch off.
If the selected function is not compatible with the
programmed wash cycle, the indicator light will flash
and the function will not be activated.
If the selected function is not compatible with
another function which has been selected previously,
the indicator light corresponding to the first function
selected will flash and only the second function will be
activated; the indicator light corresponding to the
enabled function will remain lit.
The functions may affect the recommended load
value and/or the duration of the cycle.
7. START THE PROGRAMME. Press the START/
PAUSE button. The corresponding indicator light will
become green, remaining lit in a fixed manner, and
the door will be locked (the DOOR LOCKED symbol
will be on). During the wash cycle, the name of the
phase in progress will appear on the display. To
change a wash cycle while it is in progress, pause the
washer dryer using the START/PAUSE button (the
START/PAUSE indicator light will flash slowly in an
orange colour); then select the desired cycle and
press the START/PAUSE button again.
To open the door while a cycle is in progress, press
the START/PAUSE button; if the DOOR LOCKED
symbol is switched off the door may be opened.
Press the START/PAUSE button again to restart the
wash cycle from the point at which it was interrupted.
8. THE END OF THE WASH CYCLE. This will be
indicated by the text "END OF CYCLE" on the display;
when the DOOR LOCKED
symbol switches off the
door may be opened. Open the door, unload the
laundry and switch off the machine.
If you wish to cancel a cycle which has already begun,
button. The cycle will be stopped
press and hold the
and the machine will switch off.
Wash cycles and functions
Wash cycles
Table of wash cycles
D e script io n o f t h e w a sh cycle
Max.
t e m p.
(°C)
Max.
sp e e d
(rpm )
D e t e rge n t s
D ryin g
M a x . lo a d (k g)
Fabric
Wa sh
N o rm a l
softener
M in i
L oa d
GB
Cycle
dura t ion
E ve ryd a y w a sh cycle s ( D a ily)
(1 st p re ss o f th e b u tto n ) :
Cot tons
(2 n d pre ss o f the bu tto n ) :
Cot tons
(3 rd pres s o f th e bu tto n ):
e xtre m e ly so ile d w h ite s.
h e a vily so ile d wh ite s a n d re sista n t co lo u rs.
9 0°
14 00
l
l
l
7
3
6 0°
14 00
l
l
l
7
3
4 0°
14 00
l
l
l
7
3
Syn th et ics
(1 s t pres s o f th e bu tto n ):
h e a vily so ile d re sista n t co lo u rs.
5 0°
8 00
l
l
l
3
1,5
Syn th et ics
(2 s t pres s o f th e bu tto n ):
h e a vily so ile d re sista n t co lo u rs.
4 0°
8 00
l
l
l
3
1,5
lig h tly so ile d re sista n t co lo u rs.
3 0°
8 00
l
l
l
3
1,5
3 0°
8 00
l
l
l
1
-
4 0°
8 00
l
l
l
1,5
1
3 0°
0
-
l
l
1
1
Syn th et ics (3 nd pres s o f th e
R e ady t o Wea r (* *)
h e a vily so ile d w h ite s a n d d e lica te co lo u rs.
bu tto n):
Wool: fo r w o o l, ca sh m e re , e tc.
The duration of the wash cycles can be checked
on the display.
Cot tons (*)
M e m ory: a llo w s fo r a n y w a sh cycle to b e sto re d .
Silk / Cu rta ins: fo r g a rm e n ts in silk a n d visco se , lin g e rie .
D ryin g p ro g ra m m e s
-
-
l
-
-
5
-
S yn th e tics d ry
(2 st p re ss o f th e b u tto n )
-
-
l
-
-
3
-
Wo o llm a rk d ry
(3 st p re ss o f th e b u tto n )
-
-
l
-
-
1,5
-
-
14 00
l
-
-
7
-
-
8 00
l
-
-
7
-
-
14 00
l
-
l
7
3
-
0
-
-
-
7
-
C o tto n d ry
(1 st p re ss o f th e b u tto n )
P a rt ia l w a sh cycle s
F a st sp in co tto n s
(1 st p re ss o f th e b u tto n )
S lo w sp in d e lica te s
Rin se
(2 st p re ss o f th e b u tto n )
(1 st p re ss o f th e b u tto n )
Pum p out
(2 n d p re ss o f th e b u tto n )
For all Test Institutes:
* Test wash cycle in compliance with regulation EN 50229: set wash cycle with a temperature of 60°C.
(* *) Ready to Wear
This cycle was designed to wash and dry lightly soiled small loads quickly. By selecting this cycle it is possible to wash and dry a maximum load
of 1 kg in just 60 minutes.
! Please note, this is an automatically programmed wash and dry cycle, therefore it is not possible to manually set a drying time
or drying level in conjunction with this cycle.
Wash functions
Super Wash
Because a greater quantity of water is used in the
initial phase of the cycle, and because of the
increased cycle duration, this function offers a
high-performance wash.
It cannot be used with the
, , , “Drying
programmes” and “Partial wash cycles”.
Reduced Creases
By selecting this function, the wash and spin cycles
will be modified in order to reduce the formation of
creases. At the end of the cycle the washing machine
will perform slow rotations of the drum; the “Reduced
creases” and START/PAUSE indicator lights will flash
(orange) and the text "END OF CYCLE" will appear on
the display. To end the cycle, press the START/PAUSE
button or the “Reduced creases” button.
For the Silk/Curtains cycle, the machine will end the
cycle while the laundry is soaking; the “Reduced
creases” and START/PAUSE indicator lights will flash
(orange) and the text "RINSE HOLD" will appear on the
display. To drain the water so that the laundry may be
removed, press the START/PAUSE button or the
“Reduced creases” button.
Mini Load
This function is recommended for when the load of
laundry is equal to half, or less than half, of the
maximum recommended load (see Table of wash
cycles).
It cannot be used in conjunction with the
“Drying programmes”,
programmes.
and “Pump out”
,
Timer Saver
Reduces the duration of the wash cycle.
It cannot be used with the
wash cycles”.
,
,
and “Partial
It may not be used with the
programmes”,
, , “Drying
and “Pump out” programmes.
'
Detergents and laundry
GB
Detergent dispenser drawer
Garments requiring special care
Good washing results also depend on the correct
dose of detergent: adding too much detergent will
not necessarily result in a more efficient wash, and
may in fact cause build up on the inside of your
appliance and contribute to environmental pollution.
Curtains: fold curtains and place them in a pillow
.
case or mesh bag. Use wash cycle
Wool: Hotpoint is the only washer dryer
manufacturer to have been awarded the
prestigious Woolmark Platinum Care endorsement
(M.0508) by the Woolmark Company, which means
that all woollen garments may be washed in the
washer dryer, even those which state “hand wash
on the label. Wash cycle
therefore
only”
offers complete peace of mind when washing
woollen garments in the washer dryer (max. load 1.5
kg) and guarantees optimal performance.
! Do not use hand washing detergents because
these create too much foam.
Open the detergent
dispenser drawer and
pour in the detergent or
washing additive, as
follows.
2
*
1
! Do not pour detergent into the middle compartment (*).
Detergent should only be poured into the compartment 1.
compar tment 1: Detergent for the wash
cycle (powder or liquid)
For best results liquid detergent should be poured
in the dispenser immediately before the start of
the programme.
compartment 2: Additives (fabric softeners, etc.)
The fabric softener should not overflow the grid.
Preparing the laundry
• Divide the laundry according to:
- the type of fabric/the symbol on the label
- the colours: separate coloured garments from
whites
• Empty all garment pockets and check the
buttons.
• Do not exceed the listed values, which refer to
the weight of the laundry when dry:
Durable fabrics: max. 7 kg
Synthetic fabrics: max. 3 kg
Delicate fabrics: max. 2 kg
Wool: max. 1.5 kg
Silk: max. 1 kg
How much does your laundry weigh?
1 sheet 400-500 g
1 pillow case 150-200 g
1 tablecloth 400-500 g
1 bathrobe 900-1200 g
1 towel 150-250 g
Load balancing system
Before every spin cycle, to avoid excessive vibrations and to distribute the load in a uniform manner, the drum rotates continuously at a speed
which is slightly greater than the washing rotation
speed. If, after several attempts, the load is not
balanced correctly, the machine spins at a reduced
spin speed. If the load is excessively unbalanced,
the washer dryer performs the distribution process instead of spinning. To encourage improved
load distribution and balance, we recommend small
and large garments are mixed in the load.
Precautions and tips
! This washer dryer was designed and constructed
in accordance with international safety regulations.
The following information is provided for safety
reasons and must therefore be read carefully.
General safety
• This appliance was designed for domestic use only.
• The washer dryer must only be used by adults, in
accordance with the instructions provided in this manual.
• Do not touch the machine when barefoot or with
wet or damp hands or feet.
• Do not pull on the power supply cable when
unplugging the appliance from the electricity
socket. Hold the plug and pull.
recycling of the materials they contain and reduce
the impact on human health and the environment.
The crossed out "wheeled bin" symbol on the
product reminds you of your obligation, that when
you dispose of the appliance it must be separately
collected.
Consumers should contact their local authority or
retailer for information concerning the correct
disposal of their old appliance.
Opening the porthole door manually
In the event that it is not possible to open the
porthole door due to a powercut, and if you wish to
remove the laundry, proceed as follows:
• Do not open the detergent dispenser drawer
while the machine is in operation.
• Do not touch the drained water as it may reach
extremely high temperatures.
• Never force the porthole door. This could damage
the safety lock mechanism designed to prevent
accidental opening.
• If the appliance breaks down, do not under any
circumstances access the internal mechanisms
in an attempt to repair it yourself.
• Always keep children well away from the appliance
while it is operating.
• The door can become quite hot during the wash cycle.
• If the appliance has to be moved, work in a group
of two or three people and handle it with the
utmost care. Never try to do this alone, because
the appliance is very heavy.
20
1. remove the plug from
the electrical socket.
2. make sure the water
level inside the machine is
lower than the door
opening; if it is not,
remove excess water
using the drain hose,
collecting it in a bucket as
indicated in the figure.
3. using a screwdriver,
remove the cover panel on
the lower front part of
the washer dryer (see
figure).
• Before loading laundry into the washer dryer,
make sure the drum is empty.
• During the drying phase, the door tends to get
quite hot.
• Do not use the appliance to dry clothes that have
been washed with flammable solvents (e.g.
trichlorethylene).
• Do not use the appliance to dry foam rubber or
similar elastomers.
• Make sure that the water tap is turned on during
the drying cycles.
Disposal
• Disposing of the packaging materials: observe local
regulations so that the packaging may be re-used.
• The European Directive 2002/96/EC on Waste
Electrical and Electronic Equipment, requires
that old household electrical appliances must not
be disposed of in the normal unsorted municipal
waste stream. Old appliances must be collected
separately in order to optimise the recovery and
4. pull outwards using the tab as indicated in the
figure, until the plastic tie-rod is freed from its
stop position; pull downwards and open the door at
the same time.
5. reposition the panel, making sure the hooks are
securely in place before you push it onto the
appliance.
GB
Care and maintenance
GB
Cutting off the water and
electricity supplies
• Turn off the water tap after every wash cycle.
This will limit wear on the hydraulic system inside
the Washer-dryer and help to prevent leaks.
• Unplug the Washer-dryer when cleaning it and
during all maintenance work.
Cleaning the Washer-dryer
The outer parts and rubber components of the
appliance can be cleaned using a soft cloth soaked
in lukewarm soapy water. Do not use solvents or
abrasives.
Cleaning the detergent dispenser
drawer
Remove the dispenser
by raising it and pulling
it out (see figure).
Wash it under running
water; this operation
should be repeated
frequently.
1
2
Cleaning the pump
The washer-dryer is fitted with a self-cleaning
pump which does not require any maintenance.
Sometimes, small items (such as coins or buttons)
may fall into the pre-chamber which protects the
pump, situated in its bottom part.
Make sure the wash cycle has finished and unplug
the appliance.
To access the pre-chamber:
1. using a screwdriver,
remove the cover panel
on the lower front part
of the washer-dryer
(see figure);
2. unscrew the lid by
rotating it anticlockwise (see figure): a
little water may trickle
out. This is perfectly
normal;
Caring for the door and drum of
your appliance
• Always leave the porthole door ajar in order to
prevent unpleasant odours from forming.
3. clean the inside thoroughly;
4. screw the lid back on;
5. reposition the panel, making sure the hooks are
securely in place before you push it onto the
appliance.
Checking the water inlet hose
Check the inlet hose at least once a year. If there
are any cracks, it should be replaced immediately:
during the wash cycles, water pressure is very
strong and a cracked hose could easily split open.
Never use second-hand hoses.
Troubleshooting
Your washer dryer could fail to work. Before contacting the Technical Assistance Centre (see “Assistance”),
make sure that the problem cannot be not solved easily using the following list.
GB
Problem:
Possible causes / Solutions:
The washer dryer does not
switch on.
• The appliance is not plugged into the socket fully, or is not making contact.
• There is no power in the house.
The wash cycle does not start.
•
•
•
•
•
The washer dryer door is not closed properly.
The ON/OFF button has not been pressed.
The START/PAUSE button has not been pressed.
The water tap has not been opened.
A delayed start has been set (see “How to run a wash cycle or a drying cycle”).
The washer dryer does not take
in water (the text "NO WATER,
CHECK SUPPLY" appears
on the display).
•
•
•
•
•
•
The water inlet hose is not connected to the tap.
The hose is bent.
The water tap has not been opened.
There is no water supply in the house.
The pressure is too low.
The START/PAUSE button has not been pressed.
The washer dryer continuously
takes in and
drains water.
• The drain hose is not fitted at a height between 65 and 100 cm from
the floor (see “Installation”).
• The free end of the hose is under water (see “Installation”).
• The wall drainage system is not fitted with a breather pipe.
If the problem persists even after these checks, turn off the water
tap, switch the appliance off and contact the Assistance Service. If
the dwelling is on one of the upper floors of a building, there may be
problems relating to water drainage, causing the washer dryer to fill
with water and drain continuously. Special anti-draining valves are
available in shops and help to avoid this inconvenience.
The washer dryer does not
drain or spin.
• The wash cycle does not include draining: some wash cycles require the
drain phase to be started manually (see “Wash cycles and functions”).
• The “Reduced creases” function has been activated: To complete the
wash cycle, press the START/PAUSE button (see “Wash cycles and
functions”).
• The drain hose is bent (see “Installation”).
• The drainage duct is clogged.
The washer dryer vibrates a lot
during the spin cycle.
• The drum was not unlocked correctly during installation (see “Installation”).
• The washer dryer is not level (see “Installation”).
• The washer dryer is trapped between cabinets and walls (see “Installation”).
The washer dryer leaks.
• The water inlet hose is not screwed on properly (see “Installation”).
• The detergent dispenser drawer is blocked (for cleaning instructions, see
“Care and maintenance”).
• The drain hose is not fixed properly (see “Installation”).
The machine is locked and the
display flashes, indicating an
error code (e.g. F-01, F-..).
• Switch off the machine and unplug it, wait for approximately 1
minute and then switch it back on again.
If the problem persists, contact the Technical Assistance Service.
There is too much foam.
• The detergent is not suitable for machine washing (it should display
the text “for washer dryers” or “hand and machine wash”, or the like).
• Too much detergent was used.
The washer-dryer does not dry.
•
•
•
•
•
The appliance is not plugged into the socket, or not enough to make contact.
There has been a power failure.
The appliance door is not shut properly.
A delayed start has been set.
DRYING is in the OFF position.
!
Assistance
Guarantee
GB
12 Months Parts and Labour Guarantee
Your appliance has the benefit of our manufacturer’s guarantee, which covers the cost of
breakdown repairs for twelve months from the date of purchase.
This gives you the reassurance that if, within that time, your appliance is proven to be defective
because of either workmanship or materials, we will, at our discretion, either repair or replace the
appliance at no cost to you.
This guarantee is subject to the following conditions:
-
The appliance has been installed and operated correctly and in accordance with our
operating and maintenance instructions.
The appliance is used only on the electricity or gas supply printed on the rating plate.
The appliance has been used for normal domestic purposes only.
The appliance has not been altered, serviced, maintained, dismantled, or otherwise
interfered with by any person not authorised by us.
Any repair work must be undertaken by us or our appointed agent.
Any parts removed during repair work or any appliance that is replaced become our property.
The appliance is used in the United Kingdom or Republic of Ireland.
-
The guarantee does not cover:
-
Damage resulting from transportation, improper use, neglect or interference or as a result
of improper installation.
Replacement of any consumable item or accessory . These include but are not limited to: plugs,
cables, batteries, light bulbs, fluorescent tubes and starters, covers and filters.
Replacement of any removable parts made of glass or plastic.
-
THIS GUARANTEE WILL NOT APPLY IF THE APPLIANCE HAS BEEN USED IN COMMERCIAL
OR NON-DOMESTIC PREMISES.
5 Year Parts Guarantee
Hotpoint also offers you a free 5 year parts guarantee. This additional guarantee is conditional on
you registering your appliance with us and the parts being fitted by one of our authorised engineers.
There will be a charge for our engineer's time. To activate the extra parts warranty on your
appliance, simply call our registration line on 0870 6092094 (ROI 01 230 0800).
Extended
Guarantees
We offer a selection of repair protection plans that enable you to fully cover yourself against the expense
of repair bills for the life of your policy. To find the ideal plan for you please call our advice line on
08709 088 088 (ROI 01 230 0233).
Free Helpdesk Service
We have a dedicated team who can provide free advice and assistance with your appliance if you
experience any technical difficulties within the first 90 days of ownership. Simply call our Hotpoint
Service Hotline on 08709 066 066 (ROI 0818 313 413) for telephone assistance, or, where
necessary, to arrange for an engineer to call. If we cannot resolve the technical problem we will
replace your machine or, if you prefer, give you your money back.
"
After Sales Service
GB
No one is better placed to care for your Hotpoint appliance during the course of its
working life than us - the manufacturer.
Essential Contact Information
Hotpoint Service
We are the largest service team in Europe offering you access to 400 skilled telephone advisors and
1100 fully qualified engineers on call to ensure you receive fast, reliable, local service.
UK: 08709 066 066
Republic of Ireland: 0818 313 413
www.hotpointservice.co.uk
Please note: Our advisors will require the following information:
Model number:
Serial number:
Parts and Accessories
We supply a full range of genuine replacement parts as well as accessory products that protect and
hygienically clean your appliance to keep it looking good and functioning efficiently throughout its life.
UK: 08709 07 7 07 7
Republic of Ireland: 0818 313 413
www.hotpointservice.co.uk
Appliance Registration
We want to give you additional benefits of Hotpoint ownership. To activate your free 5 year parts
guarantee you must register your appliance with us.
UK: 0870 6092094
Republic of Ireland: 01 230 0800
www.hotpointservice.co.uk
Indesit Company UK Ltd. Morley Way, Peterborough, PE2 9JB
Indesit Company Unit 49 Airways Industrial Estate,Dublin 17
Recycling & Disposal Information
As part of Hotpoint's continued commitment to helping the environment, Hotpoint reserves the right
to use quality, recycled components to keep down customer costs and minimise material wastage.
Please dispose of packaging and old appliances carefully. To minimise the risk of injury to children,
remove the door, plug and cut the mains cable off flush with the appliance. Dispose of these parts
separately to ensure that the appliance can no longer be plugged into a mains socket, and the door
cannot be locked shut.
#
195071268.00
05/2008 - Xerox Business Services
GB
$
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising