Whirlpool | WIP 4O32 PF E | Setup and user guide | Whirlpool WIP 4O32 PF E Setup and user guide

Whirlpool WIP 4O32 PF E Setup and user guide
EN
INSTRUCTION FOR USE
THANK YOU FOR BUYING A WHIRLPOOL PRODUCT.
In order to receive a more complete assistance, please register your appliance on:
www.whirlpool.eu/register
Before using the appliance carefully read Health and Safety guide.
PRODUCT DESCRIPTION
APPLIANCE
1
4
7
2
1.
Upper rack
2.
Cutlery rack
3
3.
Foldable flaps
4.
Upper rack height adjuster
5.
Upper spray arm
6.
Lower rack
7.
Space Zone
8.
Lower spray arm
9.
Filter Assembly
5
6
9
8
10
10. Salt reservoir
11. Detergent and Rinse Aid dispensers
12. Rating plate
12
13. Control panel
11
Service:
0000 000 00000
F157019
13
CONTROL PANEL
1
1.
2.
3.
4.
5.
6.
7.
8.
9.
2
3
4
5
ON-OFF button
PREVIOUS button
NEXT button
Multizone button
Display
Multizone indicator lights
Eco program indicator light
Start Delay indicator light
Program number and remaining time indicator
678
9
10 11 12 13 14
10.
11.
12.
13.
14.
15.
16.
17.
15
16
17
18
Closed water tap indicator light
Rinse Aid refill indicator light
Salt refill indicator light
Tablet Detergent (All-in-one) indicator light
Turbo button with indicator light
Power Clean® button with indicator light
Start Delay button with indicator light
START button with indicator light
1
FIRST TIME USE
SETTING MENU AND SALT
ADVICE REGARDING THE FIRST TIME USE
After installation, remove the stoppers from the racks and the retaining elastic elements from the upper rack.
5.
6.
7.
8.
Switch on the appliance by pressing the ON/OFF button.
Switch off the appliance by pressing the ON/OFF button.
Hold down START button for 5 seconds, until you hear a beep.
The display shows the first available setting (letter „A”), followed by
its value (for example: 3).
Press PREVIOUS/NEXT button to scroll the list of the available settings and to see their value (see the below table), then press START if you
want to change the value of the displayed setting: its value will start
blinking.
Use PREVIOUS/NEXT button to change the blinking value of the
selected settings, then press START to save the new value: it will
stop blinking.
To change another settings repeat steps 5-6.
To exit settings menu - press ON/OFF button.
LETTER
SETTING
VALUES
(Default - in bold)
Water Hardness Level
(see “setting the water hardness”
and “water hardness table”)
1|2|3|4|5
Rinse Aid Level
(see “ADJUSTING THE DOSAGE OF
RINSE AID”)
1|2|3|4|5
Start Program
To set the cycle to show at switch
on of the appliance.
“E”= Eco, “L”= Last cycle run
E|L
Lo | Hi
Sound Level
To adjust the volume of the sounds.
“OF” = sounds off, “Lo” = low volume,
“Hi” = high volume.
OF | Lo | Hi
Factory Settings
To restore to the factory default all
the values of the settings included
in the settings menu. After the
activation of this setting (ON), the
machine switches OFF and restores
the factory settings.
“On” = On, “OF” = Off
• It is important to set the water hardness.
The salt reservoir is located in the lower part of the dishwasher
(see PRODUCT DESCRIPTION) and should be filled when the SALT REFILL
indicator light
in the control panel is lit.
1. Remove the lower rack and unscrew the
reservoir cap (anticlockwise).
2. Only the first time you do this: fill the salt reservoir with water.
3. Position the funnel (see figure) and fill the salt
reservoir right up to its edge (approximately
1 kg); it is not unusual for a little water to leak
out.
4. Remove the funnel and wipe any salt residue
away from the opening.
Make sure the cap is screwed on tightly, so that no detergent can get
into the container during the wash program (this could damage the
water softener beyond repair).
As soon as this procedure is complete, run a program without loading.
The “Pre-Wash” program alone is not sufficient.
Residual saline solution or grains of salt can lead to corrosion, irreparably damaging the stainless steel components.
The guarantee is not applicable if faults are caused by such circumstances.
After the salt has been poured into the machine, the SALT REFILL indicator light switches off.
Only use salt that has been specifically designed for dishwashers.
If the salt container is not filled, the water softener and the heating element may be damaged as a result.
Whenever you need to add salt, it is mandatory to complete the
procedure before the beginning of the washing cycle.
SETTING THE WATER HARDNESS
Brightness Level
To adjust the brightness
level of the display.
“Lo”=Low, “Hi”= High
Light on the Floor
(see OPTIONS AND FUNCTIONS)
“On” = On, “OF” = Off
2
The use of salt prevents the formation of LIMESCALE on the dishes and
on the machine’s functional components.
• It is important that the salt reservoir be never empty.
SETTING MENU
1.
2.
3.
4.
FILLING THE SALT RESERVOIR
To allow the water softener to work in a perfect way, it is essential that
the water hardness setting is based on the actual water hardness in
your house. This information can be obtained from your local water
supplier.
The factory setting is “3” for average water hardness.
To change, follow instructions in section “SETTING MENU”.
Water Hardness Table
On | OF
On | OF
Level
°dH
°fH
German degrees
French degrees
1
Soft
0-6
0 - 10
2
Medium
7 - 11
11 - 20
3
Average
12 - 17
21 - 30
4
Hard
18 - 34
31 - 60
5
Very hard
35 - 50
61 - 90
EN
FIRST TIME USE
RINSE AID AND DETERGENT
FILLING THE RINSE AID DISPENSER
FILLING THE DETERGENT DISPENSER
Rinse aid makes dish DRYING easier. The rinse aid dispenser A should
be filled when the RINSE AID REFILL indicator light
in the control
panel is lit.
Only use detergent which has been specifically designed for
dishwashers.
To achieve the best washing and drying results, the combined use
of detergent, rinse aid liquid and refined salt is required.
We recommend using detergents that do not contain phosphates
or chlorine, as these products are harmful to the environment.
Good washing results also depend on the correct amount
of detergent being used.
B
A
1. Open the dispenser B by pressing and pulling up the tab on the lid.
2. Carefully introduce the rinse aid as far as the maximum (110 ml)
reference notch of the filling space - avoid spilling it. If this happens,
clean the spill immediately with a dry cloth .
3. Press the lid down until you hear a click to close it.
NEVER pour the rinse aid directly into the appliance tub.
ADJUSTING THE DOSAGE OF RINSE AID
If you are not completely satisfied with the drying results, you can adjust the quantity of rinse aid used.
To change, follow instructions in section “SETTING MENU”.
If the rinse aid level is set to 1 (ECO), no rinse aid will be supplied. The
LOW RINSE AID indicator light will not be lit if you run out of rinse aid.
A maximum of 5 levels can be set according to the dishwasher model.
The factory setting is “5”.
• If you see bluish streaks on the dishes, set a low number (2-3).
• If there are drops of water or limescale marks on the dishes, set
a mid-range number (4-5).
Exceeding the stated amount does not result in a more effective
wash and increases environmental pollution.
The amount can be adjusted to the soil level. In the case of normally soiled items, use approximately either 25g (powder detergent)
or 25ml (liquid detergent) and additional tea spoon of detergent
directly inside the tub. If tablets are used, one tablet will be enough.
If the crockery is only lightly soiled or if it has been rinsed with
water before being placed in the dishwasher, reduce the amount
of detergent used accordingly (minimum 20 g/ml) e.g. skip the
powder/gel putted inside the tub.
To open the detergent dispenser press button A. Introduce the
detergent into the dry dispenser B only. Place the amount of
detergent for pre-washing directly inside the tub.
B
A
1. When measuring out the detergent
refer to the mentioned earlier information to add the proper quantity..
Inside the dispenser B there are
indications to help the detergent
dosing.
2. Remove detergent residues from
the edges of the dispenser and close the cover until it clicks.
3. Close the lid of the detergent
dispenser by pulling it up until the
closing device is secured in place.
The detergent dispenser automatically opens up at the right time
according to the program.
If all-in-one detergents are used, we recommend using the TABLET
DETERGENT button, because it adjusts the program so that the best
washing and drying results are always achieved.
If you are using a all-in-one detergents, we recommend that you add
salt in any case, especially if the water is hard or very hard (follow the
instructions given on the packaging).
3
PROGRAMS TABLE
Detergent
container
Water
consumption
(litres/cycle)
Energy
consumption
(kWh/cycle)
50°
3:35
9.5
0.83
1:25 - 3:00
7.0 - 14.0
0.90 - 1.40
Drying
phase
Duration
of wash
program
(h:min)**)
Program
Available
options *)
Tub
B
P1
Eco
P2
6th Sense®
50-60°
P3
Intensive
65°
-
2:50
16.0
1.60
P4
Daily
50°
-
1:35
13.0
1.15
P5
Silent
50°
-
3:30
15.0
1.15
P6
Rapid 30’
50°
-
0:30
9.0
0.55
P7
Crystals
45°
-
1:40
11.5
1.20
P8
Pre-Wash
-
0:12
4.5
0.01
P9
Sanitizing
65°
-
1:40
10
1.30
P10 Self-Clean
65°
-
0:50
8.0
0.85
-
-
-
-
-
ECO program data is measured under laboratory conditions according to European Standard EN 50242. Note for Test Laboratories:
For information on comparative EN testing conditions, please send an email to the following address: dw_test_support@whirlpool.com
Pre-treatment of the dishes is not needed before any of the programs.
*) Not all options can be used simultaneously.
**) The duration of the program shown on the display or in the booklet is an estimate calculated on standard conditions. The actual time may vary
depending on many factors such as temperature and pressure of the incoming water, room temperature, amount of detergent, quantity and type of load,
load balancing, additional selected options and sensor calibration. The sensor calibration can increase program duration up to 20 min.
Standby consumption: Left-on mode consumption: 6 W - Off mode consumption: 0.5 W
PROGRAMS DESCRIPTION
Instructions on wash cycle selection.
P1 ECO
Normally soiled crockery. Standard program, the most efficient in
terms of its combined energy and water consumption.
P2 6 SENSE®
th
For normally soiled dishes with dried food residues. Senses the level of
soiling on the dishes and adjusts the program accordingly. When the
sensor is detecting the soil level an animation appears in the display
and the cycle duration is updated.
P3 INTENSIVE
Program recommended for heavily soiled crockery, especially suitable
for pans and saucepans (not to be used for delicate items).
P6 RAPID 30’
Program to be used for lightly-soiled dishes with no dried food residues.
P7 CRYSTALS
Program for delicate items, which are more sensitive to high temperatures, for example glasses and cups.
P8 PRE-WASH
Use to refresh crockery planned to be washed later. No detergent to be
used with this program.
P9 SANITIZING
Normally or heavily soiled crockery, with additional antibacterial wash.
P10 SELF-CLEAN
P4 DAILY
Program to be used to perform maintenance of the dishwasher.
It cleans the interior of the appliance using hot water.
P5 SILENT
Notes:
Please note that cycles like Rapid or Fast are most effective for lightly soiled
dishes. To reduce consumption even further, only run the dishwasher
when it is full.
Normally soiled crockery. Everyday cycle, that ensures optimal cleaning
and drying performance in shorter time.
Suitable for night-time operation of the appliance. Ensures optimal
cleaning and drying performance with the lowest noise emission.
4
EN
OPTIONS AND FUNCTIONS
OPTIONS can be selected directly by pressing the corresponding button (see CONTROL PANEL).
If an option is not compatible with the selected program see PROGRAMS TABLE, the corresponding LED flashes rapidly 3 times
and beeps will sound. The option will not be enabled.
MULTIZONE
If there are not many dishes to be washed, a half loading may
be used in order to save water, electricity and detergent.
Select a compatible program (see PROGRAMS TABLE) and then
press the MULTIZONE button: the symbol of the chosen rack
will appear on the display:
(only lower rack selected)
(only upper rack selected)
(only cutlery rack selected)
By default the appliance washes dishes in all racks.
Option is OFF.
START DELAY
The start of the program may be delayed for a period of time
between 0:30 and 24 hours.
1. Select the program and any desired options. Press the
DELAY button (repeatedly) to delay the start of the program.
Adjustable from 0:30 to 24 hours. When 24 hours is setting
has been reached, press the START DELAY another time to
deactivate the START DELAY function.
2. Press the START button and close the door within 4 sec. the
timer will begin counting down.
3. Once this time has elapsed, the indicator light switches off
and the program begins automatically.
The START DELAY function cannot be set once a program
has been started.
WATER TAP CLOSED – Alarm
TABLET DETERGENT (All-in-one)
This setting allows you to optimize the performance of the
program according to the type of detergent used.
Press the TABLET DETERGENT button (the corresponding
symbol will light up) if you use All-in-one detergents in
tablet form (rinse aid, salt and detergent in 1 dose).
If you use powder or liquid detergent, this option should
be off.
Flashes when there is no inlet water or water tap is closed.
OPERATION INDICATOR
A LED light projected on the floor indicates that the dishwasher
is working.
The light stays on during the cycle and switches off at the end
of the cycle.
This feature is active by default, but it is possible to deactivate
it in the “SETTINGS MENU”.
TURBO
This option can be used to reduce the duration of the main
programs while maintaining the same washing and drying
performance levels.
Select a compatible program (see PROGRAMS TABLE),
press the TURBO button and the indicator light will switch on.
To deselect the option, press the same button again.
POWER CLEAN®
Thanks to the additional power jets this option provides a more
intensive and powerful wash in the lower rack, in the specific
area (see page 6 POWER CLEAN IN LOWER RACK). This option
is recommended for washing pots and casseroles. Select a
compatible program (see “Programs table”), press this button
to activate POWER CLEAN® (the indicator lights up).
5
LOADING THE RACKS
CUTLERY RACK
FOLDABLE FLAPS WITH ADJUSTABLE POSITION
The third rack was designed to
house the cutlery.
Arrange the cutlery as shown in
the figure.
A separate arrangement of the
cutlery makes collection easier
after washing and improves washing and drying performance.
Knives and other utensils with sharp edges must be positioned
with the blades facing downwards.
LOWER RACK
The geometry of the rack makes
it possible to place such small
items as coffee cups in the area
in the middle.
UPPER RACK
The side foldable flaps can be positioned at
three different heights to optimize the arrangement of crockery inside the rack. Wine glasses can be placed safely in the foldable flaps by
inserting the stem of each glass into the corresponding slots. For optimum drying results
incline the foldable flaps more. To change the
inclination, pull up the foldable flap, slide it slightly and position it as you wish.
For pots, lids, plates, salad bowls, cutlery etc. Large plates and lids
should ideally be placed at the sides to avoid interferences with the
spray arm.
The lower rack has tip-up supports which can be used in a vertical position when arranging plates or in a horizontal position
(lower) to load pans and salad bowls easily.
Load delicate and light dishes:
glasses, cups, saucers, low salad bowls.
(loading example for the lower rack)
POWER CLEAN®
(loading example for the upper rack)
ADJUSTING THE HEIGHT OF THE UPPER RACK
The height of the upper rack can be adjusted: high position to place
bulky crockery in the lower basket and low position to make the most
of the tip-up supports by creating more space
upwards and avoid collision with the items
loaded into lower rack. The upper rack is
equipped with a Upper Rack height adjuster
(see figure), without pressing the levers, lift it up
by simply holding the rack sides, as soon as the
rack is stable in its upper position.
To restore to the lower position, press the levers
A at the sides of the rack and move the basket
downwards.
We strongly recommend that you do not
adjust the height of the rack when it is loaded.
NEVER raise or lower the basket on one side only.
6
A
Power Clean® uses the special water
jets in the rear of cavity to wash more
intensively the high dirty items.
The lower rack has a Space Zone, a
special pull-out support in the rear of
the rack that can be used to support
frying pans or baking pans in upright
position, thus taking up less space.
Placing the pots/casseroles faced to the Power Clean® component please
activate the POWER CLEAN® on the panel.
How to use Power Clean®:
1. Adjust the Power Clean® area
G folding down the rear plate
holders to load pots.
2. Load pots and casseroles inclined vertically in Power Clean®
area. Pots have to be inclined
towards the power water jets.
EN
DAILY USE
1. CHECK WATER CONNECTION
Check that the dishwasher is connected to the water supply and
that the tap is open.
2. LOAD THE RACKS
(see LOADING THE RACKS).
The machine will switch off automatically during certain extended
periods of inactivity, in order to minimise electricity consumption.
If the crockery is only lightly soiled or if it has been rinsed with
water before being placed in the dishwasher, reduce the amount
of detergent used accordingly.
3. FILLING THE DETERGENT DISPENSER
(see PROGRAMS TABLE).
MODIFYING A RUNNING PROGRAM
4. SWITCH ON THE DISHWASHER
Open the door and press the ON/OFF button.
Please note that buttons are deactivated while door is opened
more then 3/4 from vertical (closed) position.
5. CHOOSE THE PROGRAM AND CUSTOMISE THE CYCLE
Select the most appropriate program in accordance with the type
of crockery and its soiling level (see PROGRAMS DESCRIPTION).
The display shows the letter “P” followed by the number of the
program (e.g. “P 1”). Pressing the button PREVIOUS / NEXT changes
the program.
Select the desired options (see OPTIONS AND FUNCTIONS).
6. START
Start the wash cycle by pressing START button (led is lit) and
closing the door within 4 sec. When the program starts you hear
a single beep. If the door was not closed within 4sec., the alarm
sound will be played. In this case, open the door, press START
button and close the door again within 4 sec.
7. END OF WASH CYCLE
The end of the wash cycle is indicated by beeps and the display
shows “End”. Open the door and switch off the appliance by pressing the ON/OFF button.
Wait for a few minutes before removing the crockery - to avoid
burns. Unload the racks, beginning with the lower one.
If a wrong program was selected, it is possible to change it, provided
that it has only just begun: open the door, press and hold the
ON/OFF button, the machine will switch off.
Switch the machine back on using the ON/OFF button and select
the new wash cycle and any desired options; Start the wash cycle by
pressing START button and closing the door within 4 sec.
ADDING EXTRA CROCKERY
Without switching off the machine, open the door (the “:” stops blinking and START led starts blinking) (beware of HOT steam!) and place
the crockery inside the dishwasher. Press the START button and close
the door within 4 sec., the cycle will resume from the point at which it
was interrupted.
ACCIDENTAL INTERRUPTIONS
If the door is opened during the wash cycle, or if there is a power cut,
the cycle stops. Press the START button and close the door within 4
sec., the cycle will resume from the point at which it was interrupted.
ADVICE AND TIPS
TIPS
Before loading the baskets, remove all food residues from the crockery and empty the glasses. You do not need to rinse beforehand
under running water.
Arrange the crockery so that it is held in place firmly and does not tip
over; and arrange the containers with the openings facing downwards and the concave/convex parts placed obliquely, thus allowing
the water to reach every surface and flow freely.
Warning: lids, handles, trays and frying pans do not prevent the
sprayer arms from rotating.
Place any small items in the cutlery basket.
Very soiled dishes and pans should be placed in the lower basket because in this sector the water sprays are stronger and allow a higher
washing performance.
After loading the appliance, make sure that the sprayer arms can
rotate freely.
HYGIENE
To avoid odour and sediment which can be accumulated in the dishwasher please run a high temperature program at least one a month.
Use a tea spoon of detergent and run it without the loading to clean
your appliance.
UNSUITABLE CROCKERY
• Wooden crockery and cutlery.
• Delicate decorated glasses, artistic handicraft and antique crockery.
Their decorations are not resistant.
• Parts in synthetic material which do not withstand high temperatures.
• Copper and tin crockery.
• Crockery soiled with ash, wax, lubricating grease or ink.
The colours of glass decorations and aluminium/silver pieces can
change and fade during the washing process. Some types of glass
(e.g. crystal objects) can become opaque after a number of wash
cycles too.
DAMAGE TO GLASS AND CROCKERY
• Only use glasses and porcelain guaranteed by the manufacturer as
dishwasher safe.
• Use a delicate detergent suitable for crockery
• Collect glasses and cutlery from the dishwasher as soon as the
wash cycle is over.
7
CARE AND MAINTENANCE
ATTENTION: Always unplug the appliance when cleaning it and
when performing maintenance work. Do not use flammable liquids
to clean the machine.
CLEANING THE DISHWASHER
Any marks on the inside of the appliance may be
removed using a cloth dampened with water and
a little vinegar.
The external surfaces of the machine and the control panel can be cleaned using a non-abrasive cloth
which has been dampened with water. Do not use
solvents or abrasive products.
After several washes, check the filter assembly and if necessary clean
it thoroughly under running water, using a non-metallic brush and
following the instructions below:
1. Turn the cylindrical filter A in an anti-clockwise direction and pull
it out (Fig 1).
2. Remove the cup filter B by exerting a slight pressure on the side
flaps (Fig 2).
3. Slide out the stainless-steel plate filter C (Fig 3).
4. Inspect the trap and remove any food residues. NEVER REMOVE
the wash-cycle pump protection (black detail) (Fig 4).
12
PREVENTING UNPLEASANT ODOURS
Always keep the door of the appliance ajar in order to avoid moisture
from forming and being trapped inside the machine.
Clean the seals around the door and detergent dispensers regularly
using a damp sponge. This will avoid food becoming trapped in the
seals, which is the main cause behind the formation of unpleasant
odours.
CHEKING THE WATER SUPPLY HOSE
A
B
A
34
Check the inlet hose regularly for brittleness and cracks. If damaged,
replace it by a new hose available through our After-Sales Service or
your specialist dealer. Depending on the hose type:
C
If the inlet hose has a transparent coating, periodically check if the
colour intensifies locally. If yes, the hose may have a leak and should
be replaced.
For water stop hoses: check the small safety valve inspection window
(see arrow). If it is red, the water stop function was triggered, and the
hose must be replaced by a new one.
For unscrewing this hose, press the release button while unscrewing
the hose.
CLEANING THE WATER INLET HOSE
If the water hoses are new or have not been used for an extended
period of time, let the water run to make sure it is clear and free of
impurities before performing the necessary connections. If this
precaution is not taken, the water inlet could become blocked and
damage the dishwasher.
CLEANING THE FILTER ASSEMBLY
Regularly clean the filter assembly so that the filters do not clog and
that the waste water flows away correctly.
The filter assembly consists of three filters which remove food residues from the washing water and then recirculate the water: to obtain
the best washing results, you need to keep them clean.
The dishwasher must not be used without filters or if the filter is
loose.
8
After cleaning the filters, re-place the filter assembly and fix it in
position correctly; this is essential for maintaining the efficient
operation of the dishwasher.
CLEANING THE SPRAY ARMS
On occasions, food residue may become encrusted onto the spray arms
and block the holes used to spray the
water. It is therefore recommended
that you check the arms from time
to time and clean them with a small
non-metallic brush.
To remove the upper spray arm, turn
the plastic locking ring in an
anti-clockwise direction. The upper
spray arm should be replaced so that
the side with the greater number of holes is facing upwards.
The lower spray arm may be removed by pulling it upwards.
EN
INSTALLATION
ATTENTION: If the appliance must be moved at any time, keep it
in an upright position; if absolutely necessary, it may be tilted onto
its back.
CONNECTING THE WATER SUPPLY
Adaptation of the water supply for installation should only be performed by a qualified technician.
The water inlet and outlet hoses may be positioned towards the right
or the left in order to achieve the best possible installation.
Make sure the dishwasher does not bend or squash the hoses.
CONNECTING THE WATER INLET HOSE
• Run the water until it is perfectly clear.
• Screw the inlet hose tightly into position and turn on the tap.
If the inlet hose is not long enough, contact a specialist store or an
authorised technician.
The water pressure must be within the values indicated in the Technical Data table - otherwise the dishwasher may be function properly.
Make sure the hose is not bent or compressed.
SPECIFICATIONS FOR THE CONNECTION OF THE WATER SUPPLY HOSE:
WATER SUPPLY
cold or hot (max. 60°C)
WATER INTAKE
3/4”
POWER OF WATER PRESSURE
0,05 ÷ 1 MPa (0.5 ÷ 10 bar)
7,25 – 145 psi
CONNECTING THE WATER OUTLET HOSE
Connect the outlet hose to a drain duct with a minimum diameter of
2 cm A.
The outlet hose connection must be at a height ranging from 40 to
80 cm from the floor or surface where the dishwasher rests.
MAX 80 cm
MIN 40 cm
Before connecting the water outlet hose to the sink drain, remove the
plastic plug B.
ANTI-FLOODING PROTECTION
Anti-flooding protection. To ensure floods do not occur, the dishwasher:
- is provided with a special system which blocks the water supply in
the event of anomalies or leaks from inside the appliance.
Some models are also equipped with the supplementary safety device
New Aqua Stop, which guarantees anti-flooding protection even in
the event of a supply hose rupture.
Under no circumstances should the water inlet hose be cut as it contains live electrical parts.
ELECTRICAL CONNECTION
WARNING: Under no circumstances should the water inlet hose
be cut as it contains live electrical parts.
Before inserting the plug into the electrical socket, make sure that:
• The socket is earth
and complies with current regulations;
The socket can withstand the maximum load of the appliance as
shown on the data plate located on the inside of the door (see
PRODUCT DESCRIPTION).
• The power supply voltage falls within the values indicated on the
data plate on the inside of the door.
• The socket is compatible with the plug of the appliance.
If this is not the case, ask an authorised technician to replace the plug
(see AFTER-SALES SERVICE). Do not use extension cables or multiple
sockets. Once the appliance has been installed, the power supply
cable and the electrical socket should be easily accessible.
The cable should not be bent or compressed.
If the power supply cable is damaged, have it replaced by the manufacturer or its authorised Technical Assistance Service in order to
prevent all potential hazards.
The Company shall not be held responsible for any incidents, if these
regulations are not observed.
POSITIONING AND LEVELLING
1. Position the dishwasher on a level sturdy floor. If the floor is uneven, the front feet of the appliance may be adjusted until it reaches
a horizontal position. If the appliance is levelled correctly, it will be
more stable and much less likely to move or cause vibrations and
noise while it is operating.
2. Before recessing the dishwasher, stick the adhesive transparent
strip under the wooden shelf in order to protect it from any condensation which may form.
3. Place the dishwasher so that its sides or back panel are in contact
with the adjacent cabinets or the wall. This appliance can also be
recessed under a single worktop.
4. To adjust the height of the rear foot, turn the red hexagonal
bushing on the lower central part at the front of the dishwasher
using a hexagonal spanner with an opening of 8 mm. Turn the
spanner in
a clockwise direction to increase the height and in an anticlockwise
direction to decrease it.
DIMENSIONS AND CAPACITY:
WIDTH
598 mm
HEIGHT
820 mm
DEPTH
555 mm
CAPACITY
14 standard place-settings
9
TROUBLESHOOTING
Your dishwasher may not work properly.
Before contacting the Service Centre check if the problem can be solved by going through the following list.
PROBLEMS
POSSIBLE CAUSES
SOLUTIONS
The dishwasher
won’t start
or does not
respond to commands.
The appliance has not been plugged in properly.
Insert the plug into the socket.
Power outage.
The dishwasher starts automatically when the power returns.
The dishwasher door is not closed.
Vigorously push the door until you hear the “click”.
It does not respond to commands.
Switch off the appliance by pressing the ON/OFF button, switch it
back on after approximately one minute and reset the program.
Racks are not fit to the end.
Verify that racks are fit to the end.
The door is not lock.
Vigorously push the door until you hear the “clack” sound.
The dishes are rattling against each.
Position the crockery correctly (see LOADING THE RACKS).
An excessive amount of foam has been produced.
The detergent has not been measured out correctly or it is not
suitable for use in dishwashers (see FILLING THE DETERGENT
DISPENSER). Reset the current cycle by switching OFF the dishwasher, then switch it on again, select a new program, press START
and close the door. Please do not add any detergent.
The selected program hasn’t any drying phase.
Verify on the programs table if the selected program has the drying
phase.
The rinse aid has run out or the resolution is not
adequate.
Add the rinse aid or adjust the dosage levels higher (see FILLING
THE RINSE AID DISPENSER).
The dishes are made of non-stick or plastic.
It is normal the presence of drops of water (see TIPS).
The crockery has not been arranged properly.
Arrange the crockery correctly (see LOADING THE RACKS).
The spray arms cannot rotate freely, being hindered
by the dishes.
Arrange the crockery correctly (see LOADING THE RACKS).
The wash cycle is too gentle.
Select an appropriate wash cycle (see PROGRAMS TABLE).
An excessive amount of foam has been produced.
The detergent has not been measured out correctly or it is not suitable
for use in dishwashers (see FILLING THE DETERGENT DISPENSER). Reset
the current cycle by switching OFF the dishwasher, then switch it on
again, select a new program, press START and close the door. Please do
not add any detergent.
The cap on the rinse aid compartment has not been
shut correctly.
Make sure the cap of the rinse aid dispenser is closed.
The filter is soiled or clogged.
There is no salt.
Clean the filter assembly (see CARE AND MAINTENANCE).
Fill the salt reservoir (see FILLING THE SALT RESERVOIR).
The dishwasher
does not fill the
water, shows
„H2O” Warning
or „F06”
No water in the water supply or the tap is closed.
Make sure there is water in the water supply or the tap running.
The sieve in the water inlet hose is clogged; it is
necessary to clean it.
Make sure the drain hose is not bent (see INSTALLATION) reprogram the dishwasher and reboot.
After having carried out the verification and cleaning, turn off and
turn on the dishwasher and restart a new program.
The dishes and
glasses show
calcination or a
whitish film.
The salt level is too low.
Fill the salt reservoir (see FILLING THE SALT RESERVOIR).
The adjustment of the water hardness is not adequate.
Increase the values (see WATER HARDNESS TABLE).
The cap of the salt reservoir is not properly closed.
The rinse aid is used up or the dosage is insufficient.
Check to have properly closed the salt reservoir cap.
Add the rinse aid or adjust the dosage levels higher.
The rinse aid dosage is excessive.
Adjust the dosage rates below.
The door doesn’t
lock.
The dishwasher
makes excessive
noise.
The dishes have
not been dried.
The dishes are
not clean.
The dishes and
glasses are blue
streaked or have
a bluish tinge.
10
The inlet hose is bent.
EN
PRODUCT FISCHE
The technical data containing the energy consumption data can be
downloaded from the website: docs. whirlpool.eu
CONTACTING AFTER-SALES SERVICE
You can find our contact details in the warranty manual. When contacting our Client
After-sales Service, please state the codes
provided on your product’s rating plate.
IEC 436
:
11
400011386908
07/2019 ks - Xerox Fabriano
12
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising