Whirlpool | HDN SI840 | Instruction for Use | Whirlpool HDN SI840 Instruction for Use

Whirlpool HDN SI840 Instruction for Use
D
Betriebs- und Wartungshandbuch
GB
User and Maintenance Handbook
Enthält auch Anweisungen und Vorschriften für die sichere Installation.
Lesen Sie die vorliegenden Anweisungen und das beiliegende Installationshandbuch vor der
Installation oder dem Gebrauch der Abzugshaube aufmerksam durch und befolgen Sie sie.
WARNUNG: Berücksichtigen Sie bei der Installation den Mindestabstand von den Flammen, wie
im Installationshandbuch angegeben.
Schreiben die Installationsanweisungen des Gaskochfelds einen größeren Abstand vor, ist dieser
natürlich zu beachten.
Also contains instructions and regulations for safe installation
Before installing or using the hood, carefully read and follow the instructions given in this
handbook and in the enclosed installation handbook.
WARNING: Be sure to observe the minimum installation distance from cookers, which is indicated
in the installation handbook.
If the installation instructions for the gas cooker specify a greater distance, this must be taken into
account.
F
Manuel d'utilisation et d'entretien
Contient également les instructions et prescriptions pour une installation sûre
Avant de monter ou d'utiliser la hotte, lire et suivre attentivement les instructions
reportées dans ce manuel et dans le manuel d'instructions en annexe.
AVERTISSEMENT : Respecter la distance minimum d'installation entre les feux indiquée sur le
manuel de montage.
Si les instructions d'installation du dispositif de cuisson à gaz indiquent une distance supérieure, il est
nécessaire de la respecter.
I
Libretto di Uso e Manutenzione
Contiene anche istruzioni e prescrizioni per una sicura installazione
Prima di installare o utilizzare la cappa, leggete e seguite attentamente le istruzioni
riportate in questo libretto e nel libretto di installazione allegato.
AVVERTENZA: Rispettare la distanza minima di installazione dai fuochi indicata sul libretto di
installazione.
Se le istruzioni di installazione del dispositivo di cottura a gas specificano una distanza maggiore,
bisogna tenerne conto.
5019 618 33091/A
LI246A
SAFEGUARDING THE ENVIRONMENT
1. Packing
Packing materials are 100% recyclable and are marked with
the recycling symbol .Comply with the local regulations for
disposal. The packing materials (plastic bags, polystyrene,
etc.) are a potential source of danger and must be kept out of
the reach of children.
2. Product
This appliance is marked in compliance with European
Directive 2002/96/EC, Waste Electrical and Electronic
Equipment (WEEE).
By ensuring that this appliance is correctly scrapped, the user
can help prevent potentially harmful consequences for the
environment and the health of people.
The symbol on the product or the accompanying
documentation indicates that this product should not be treated
as domestic waste but must be taken to a suitable collection
centre for the recycling of electrical and electronic equipment.
Disposal must be carried out in compliance with local
regulations on waste disposal.
For further information on the treatment, recovery and
recycling of this product, contact the competent local office,
the household waste collection service or the shop where
you purchased the appliance.
IMPORTANT INSTRUCTIONS FOR
SAFETY
WARNING: To reduce the risk of accidents, electric
shock, injury or damage, when using the hood comply with
the basic precautions, including the following.
1. Always disconnect the hood from the power supply
before carrying out any installation or maintenance
operation on the appliance.
2. Installation must be carried out by a specialised
technician, in compliance with the manufacturer’s
instructions and local safety regulations.
3. Earthing of the appliance is compulsory. (Not possible for
Class II hoods).
4. Never use multisockets and extension leads.
5. The electrical components must no longer be accessible
to the user after installation.
6. Do not touch the hood with wet parts of the body or use
it when barefoot.
7. Do not pull the appliance power cable to unplug it.
8. After-sales service – do not repair or replace any part of
the hood unless specifically indicated in the manual. All
other maintenance services must be carried out by a
specialised technician.
9. When drilling the wall, make sure not to damage the
electrical connections and/or pipes.
10. The ventilation ducts must always discharge to the
outside.
11. The Manufacturer declines any liability for improper use
or incorrect setting of the controls.
12. The appliance is not intended for use by children or
persons with limited physical, sensory or mental abilities
or without experience and knowledge of it, unless they
are under the supervision of or instructed in its use by a
person responsible for their safety.
13. Keep children away.
14. To reduce the risk of fire, only use a metal inlet duct.
15. Children must be supervised so that they do not play
with the appliance.
16. The product must be disposed of in compliance with
local regulations on waste disposal.
17. For further information on the treatment, recovery and
recycling of this product, contact the competent local
office, the household waste collection service or the shop
where you purchased the appliance.
18. Regular cleaning and maintenance is essential for correct
hood operation and good performance. Frequently clean
all encrustations from dirty surfaces to prevent the
accumulation of grease. Regularly clean or replace filters.
19. Do not “flambé” food under the hood. Naked flames
could cause a fire.
20. The room must have adequate ventilation when the hood
is used at the same time as appliances operating on gas or
other fuels.
21. The discharge air must not be eliminated in a duct used
to remove fumes produced by appliances operating on
gas or other fuels, but must have a separate outlet. All the
national regulations on air discharge envisaged by art.
7.12.1 of CEI EN 60335-2-31 must be observed.
22. If the hood is used together with other appliances
operating on gas or other fuels, the negative pressure in
the room must not exceed 4 Pa (4 x 10-5 bar). Therefore,
make sure the room is adequately ventilated.
23. Do not leave pans unattended when frying, since the
cooking oil could catch fire.
24. Make sure the lamps are cold before touching them.
25. The hood is not a shelf, therefore do not overload or
place objects on it.
26. Do not use or leave the hood without its lamps correctly
installed - risk of electric shock.
27. Wear work gloves for all installation and maintenance
operations.
28. The product is not suitable for outdoor use.
29. The air sucked by the hood must not be eliminated
through the same flue of the heating system or other
appliances using gas or other fuels.
5019 618 33091/A
LI246A
D
GB
F
I
Electrical connection
The mains voltage must match that given on the rating plate
located inside the hood. If provided with a plug, connect the
hood to a socket complying with the current regulations and
located in an accessible area. If it does not have a plug (direct
connection to the power supply) or if the plug is not in an
accessible place, fit a suitable double-pole switch that ensures
complete disconnection from the power supply in category III
overvoltage conditions, complying with the installation rules.
WARNING: Before reconnecting the hood circuit to the
power supply and checking correct operation, always make
sure the power cable is correctly fitted and that it was NOT
crushed in its housing during installation. Make sure to have
this operation carried out by a specialised technician.
Cleaning the hood
WARNING: Failure to remove oil/grease (at least once a
month) could result in fire.
Use a soft cloth with a neutral detergent. Never use abrasive
substances or alcohol.
Before using the hood
Please read these instructions carefully and keep them for
future reference, in order to ensure best use of your hood.
The packing materials (plastic bags, polystyrene, etc.) are a
potential source of danger and must be kept out of the reach
of children.
Make sure the hood has not been damaged during transport.
AFTER-SALES SERVICE
Before calling the After-Sales Service
1. Check to see if you can fix the problem yourself
(see “Troubleshooting Guide”).
2. Switch the appliance off and then on again to check if the
problem has been eliminated.
3. If the problem persists, contact the After-Sales Service.
Specify:
• the type of fault,
• the product model given on the dataplate inside the
hood, visible on removing the grease filters,
• your full address,
• your telephone number and area code,
• the Service code (the number under the word SERVICE
on the dataplate inside the hood, behind the grease
filter).
If any repairs are necessary, contact an authorised Service
Centre (to ensure the use of original spare parts and correct
repair).
Failure to comply with these instructions can compromise
the safety and quality of the product.
Declaration of conformity
This product has been designed, manufactured and put on
the market in conformity with:
- safety objectives of the “Low Voltage” Directive
2006/95/EC (which replaces 73/23/EEC as amended)
- protection requirements of “EMC” Directive 89/336/EEC
amended by Directive 93/68/EEC.
Troubleshooting guide
If the hood does not work:
• Is the plug properly inserted in the power socket?
• Is there a power failure?
If the hood is not extracting enough:
• Is the right speed selected?
• Do the filters need cleaning or replacing?
• Are the air outlets blocked?
If the lamp does not work:
• Does the lamp need replacing?
• Is the lamp correctly fitted?
5019 618 33091/A
LI246A
D
GB
F
I
The hood is designed for use in “Extractor version” or in
“Filter version”
Extractor version
(see symbol
in the installation handbook)
Fumes are extracted and expelled to the outside through an
exhaust pipe (not supplied) fixed to the hood coupling ring.
Depending on the exhaust pipe purchased, provide for
suitable fixing to the coupling ring.
Important: If already installed, remove the carbon filter/s.
Filter version
(see symbol
in the installation handbook)
Air is filtered through the carbon filter/s and recycled into the
surrounding environment.
Important: Ensure that air recirculation is facilitated
(carefully follow the instructions given in the installation
handbook)
Important! If the hood does not have a carbon filter/s, it/they
must be ordered and fitted before use.
The hood is provided with hardware (e.g. screws and/or
plugs) suitable for most walls/ceilings. However, it is necessary
to contact a qualified technician to ensure suitability according
to the type of wall/ceiling. The wall/ceiling must be strong
enough to take the weight of the hood.
Very heavy product; hood handling and installation
must be carried out by at least two persons.
5019 618 33091/A
LI246A
D
GB
F
I
PRODUCT SHEET
1.
2.
3.
4.
5.
CONTROL PANEL
Light button.
Press the button to switch on the lights.
Extraction speed selection button.
Press the button to select the power/speed.
Keep the button pressed for 2 seconds to go to OFF
status.
Control panel.
Grease filter
Light
Steam deflector
Telescopic flue
Warning! The hood can support a maximum weight of 5 kg
Bulb maintenance
f1
1. Disconnect the hood from the power supply.
2. Use a small screwdriver or another suitable tool to prise
and remove the lighting unit (Fig.1).
3. Replace the damaged lamp.
4. Only use 20 W max. - G4 halogen lamps, taking care not
to touch them with hands.
5. Close the lighting unit (snap-on).
f2
Grease filters:
Fig. 2
The metal grease filter has an unlimited life and must be
washed once a month by hand or in a dishwasher at a low
temperature and with short cycle. Washing in a dishwasher
can cause the grease filter to become opaque, but its filtering
capacity is not affected.
Grease filter maintenance:
1. Disconnect the hood from the power supply.
2. Remove the grease filter/s (Fig. 2). to remove it/them
pull the spring release handle backwards (f1) then remove
the filter/s downwards (f2)
Carbon filter maintenance
(for models with filter installation):
The carbon filter must be washed once a month in a
dishwasher at the highest temperature, using a normal
dishwasher detergent. It is advisable to wash the filters
separately.
After washing, reactivate the carbon filter by drying it in the
oven at 100° C for 10 minutes.
Change carbon filter every 3 years
Fitting the carbon filter:
1. Remove the grease filter (f1/f2 - Fig. 2).
2. Remove the filter holder by turning the knobs 90°
(g - Fig. 3).
3. Fit the carbon filter (i - Fig. 3) in the filter holder (h - Fig. 3).
Proceed in reverse order to refit the filter holder and grease
filter.
5019 618 33091/A
LI246A
D
GB
F
I
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising