Whirlpool | PWD9060 | Setup and user guide | Whirlpool PWD9060 Setup and user guide

Whirlpool PWD9060 Setup and user guide
PWD9060
WASHER DRYER
PWD9060
User Manual
POINT SERIES PTC WASHING MACHINE.
POINT SERIES PTC VASKEMASKIN.
POINT SERIES PTC VASKEMASKIN.
POINT SERIES PTC VASKEMASKINE.
POINT SERIES PTC TVÄTTMASKIN.
Quick Guide
EN
THANK YOU FOR PURCHASING A POINT PRODUCT.
Before using the appliance carefully read the Health and Safety guide.
Before using the appliences carefully read the Safety Instructions. Before using the machine,
it is imperative that the transport bolts are removed. For more detailed instructions on how
to remove them, see the Installation Guide (pag. 10)
CONTROL PANEL
1
1. ON/OFF button
2. CLEANING ACTION button
3. DRYING button
4. START/PAUSE button and indicator light
5. TEMPERATURE button
6. CHILD LOCK button
7. FUNCTION buttons
8. DELAY button
9. ANTI ALLERGY RINSE button
10. MY CYCLE button
11. WASH CYCLE SELECTOR buttons
2
3
DISPLAY
11
WASH CYCLE TABLE
7
9 8
10
Default
Range
Maximum
spin
(r.p.m.)
Max.
load
(kg)
1
White (Whites)
60 °C
- 90 °C
1400
9
2
Cotton (Cottons) (1st press of the button) (2)
40 °C
- 60 °C
1400
9
2
Eco Cotton (Eco Cottons) (2nd press of the button) (1)
60 °C
- 60 °C
1400
9
3
Synthetics (Synths Resistant)
40 °C
- 60 °C
1000
4,5
4
Fast Wash 30’ (Fastwash) (1st press of the button)
30 °C
- 30 °C
800
3,5
4
Wool (Woolmark Platinum) (2nd press of the button)
40 °C
- 40 °C
800
2
4
Delicates (3rd press of the button)
30 °C
- 30 °C
0
1
M
My Cycle (Memory): allows for any wash cycle to be stored.
6
Anti Stain (1st press of the button)
40 °C
- 40 °C
1400
5
6
Anti Stain Quick (2nd press of the button)
40 °C
- 40 °C
1200
4,5
7
Wash & Dry 45’ (Ready to Wear)
30 °C
- 30 °C
1400
1
8
Drying Cotton (Cotton Dry) (1st press of the button)
Drying Synthetics (Synthetics Dry) (2nd press of the
button)
Drying Wool (Wool Dry) (3rd press of the button)
–
–
–
6
–
–
–
4
–
–
–
2
Spin (1st press of the button)
–
–
1400
9
Rinse (2nd press of the button)
–
–
1400
9
Pump out (3rd press of the button)
–
–
0
9
8
8
Duration
(Minutes)
The duration of the wash cycles can be checked on the display.
Temperature
Wash cycle
Drying
Maximum load 9 kg
Power input in off mode 0.5 W / in left-on mode 8 W
6 5 4
Detergents and Recommended
Additives
detergent
Fabric
Wash softener
Powder Liquid
1
2




















–


–




–




–




–





–



–


–
–
–
–

–
–
–
–

–
–
–
–

–
–
–
–

–

–
–
–
–
–
–
–
 Required dosage  Optional dosage
The cycle duration indicated on the display or instruction manual is an estimate based on
standard conditions. The actual duration may vary in relation to several factors, such as
the temperature and pressure of the incoming water, ambient temperature, amount of
detergent, load quantity and type, load balancing and any additional options selected.
1) Test programme in compliance with standard EN 50229 (Wash): set wash cycle 2 with a
temperature of 60°C (2nd press of the button).
Test programme in compliance with standard EN 50229 (Drying): select the 2 wash
programme; temperature 60°C (2nd press of the button) and set the drying level to “Extra”, for
both loads. The first drying cycle must be carried out with the nominal load.
For all testing institutes:
2) Long cotton cycle: set programme 2 at temperature 40°C (1st press of the button).
DETERGENT DISPENSER DRAWER
PRODUCT DESCRIPTION
1. Top
2. Detergent dispenser drawer
3. Control panel
4. Handle
5. Porthole door
6. Drain pump (behind the plinth)
7. Plinth (removable)
8. Adjustable feet (2)
1.
2.
3.
4.
5.
6.
7.
8.
A
Compartment *:
B
Do not insert detergent in this compartment.
Compartment 1: Washing detergent (powder
or liquid)
If liquid detergent is used, the removable plastic
* 1
2
partition A (supplied) should be used for proper
dosage.
If powder detergent is used, place the partition
into slot B.
Compartment 2: Additives (fabric softeners, etc.)
The fabric softener must not exceed the “MAX” level.
! Use powder detergent for white cotton garments, for pre-washing, and
for washing at temperatures over 60°C.
! Follow the instructions given on the detergent packaging.
WASH CYCLES
Follow the instructions on the symbols of the garment’s wash
care label. The value indicated in the symbol is the maximum
recommended temperature for washing the garment.
White
for heavily soiled whites and resistant colours.
Cotton
suitable for washing towels, underwear, table cloths, etc. made of
resistant linen and cotton that are moderately to heavily soiled.
Eco Cotton
Suitable for washing moderately soiled cotton garments. At 40°C and
60°C it is the standard cycle for washing cotton garments, and is the most
efficient in terms of combined water and electricity consumption.
Synthetics
Suitable for washing moderately soiled garments made of synthetic fibres
(e.g. polyester, polyacrylic, viscose, etc.) or mixed synthetic-cotton fibres.
Fast Wash 30’
For washing lightly soiled garments in a short time. Not suitable for wool,
silk and garments to be washed by hand.
Wool
all wool garments can be washed using programme 4, even those
carrying the “hand-wash only”
label. For best results, use special
detergents and do not exceed 2 kg of laundry.
Delicates
this programme is ideal for washing very delicate garments having
strasses or sequins.
We recommend turning the garments inside out before washing and
placing small items into the special bag for washing delicates. Use liquid
detergent on delicate garments for best results.
When selecting an exclusively time-based drying function, a drying cycle
is performed at the end of the wash cycle that is particularly delicate,
thanks to light handling and appropriate temperature control of the
water jet.
The recommended durations are:
1 kg of synthetic garments --> 160 min
1 kg of synthetic and cotton garments --> 180 min
1 kg of cotton garments --> 180 min
The degree of dryness depends on the load and fabric composition.
Anti Stain
this programme is suitable to heavily-soiled garments with resistant
colours. It ensures a washing class that is higher than the standard class (A
class). When running the programme, do not mix garments of different
colours. We recommend the use of powder detergent. Pre-treatment with
special additives is recommended if there are obstinate stains.
If the drying function is selected, a drying cycle automatically activates at
the end of the wash cycle that resembles open-air drying, with the added
advantages of preserving garments from yellowing due to sunlight
exposure and preventing loss of whiteness caused by the possible
presence of dust in the air. Drying cycles can only be selected on a level
basis. Dryness level “Hanger” recommended.
Anti Stain Quick
this programme is ideal for washing the most difficult daily stains in 1
hour. It is ideal for mixed fabrics and coloured garments, caring for your
clothes as it washes.
If the drying function is selected, a drying cycle automatically activates at
the end of the wash cycle that resembles open-air drying, with the added
advantages of preserving garments from yellowing due to sunlight
exposure and preventing loss of whiteness caused by the possible
presence of dust in the air. Drying cycles can only be selected on a level
basis. Dryness level “Hanger” recommended.
Wash & Dry 45’
select this programme for washing and drying lightly soiled garments
(Cottons and Synthetics) in a short time. This cycle may be used to wash
and dry a laundry load of up to 1 kg in just 45 minutes.
To achieve optimum results, use liquid detergent and pre-treat cuffs, collars
and stains.
Drying Cotton
To dry cotton garments.
Drying Synthetics
To dry synthetics garments.
Drying Wool
To dry wool garments.
Spin
designed for spinning.
Rinse
designed for rinsing and spinning.
Pump out
designed for draining the water.
DISPLAY
The display is useful when programming the machine and provides a
great deal of information.
Z
B
A
X
D
C
E
Y
F
The upper two strings A and B are used to display the selected wash
cycle or the type of drying selected, the current wash cycle phase (the
selected dryness level or drying time) and all the indications relating to
the progress status of the cycle.
String C shows the time remaining until the end of the wash cycle in
progress and, if a DELAYED START has been set, the time remaining until
the start of the selected wash cycle.
String D shows the maximum spin speed value (this depends on the
selected wash cycle); if the wash cycle does not include a spin cycle, the
string remains unused.
String E shows the maximum temperature value which may be selected
(this depends on the wash cycle used); if the temperature of the wash
cycle cannot be modified, the string remains unused.
Indicator lights F correspond to the functions and light up when the
selected function is compatible with the set wash cycle.
Locked door indicator
When lit, the symbol indicates that the door is locked. To prevent any
damage, wait until the symbol turns off before opening the door.
To open the door while a cycle is in progress, press the START/PAUSE
button
; if the
symbol is off, the door can be opened.
FIRST-TIME USE
Once the appliance has been installed, and before it is used for the first
time, run a wash cycle with detergent and no laundry, by setting the “Auto
Clean” cycle.
DAILY USE
Prepare the laundry by following the suggestions appearing under the
“TIPS AND SUGGESTIONS” section.
- Press the ON/OFF button ; “POWER ON” will appear on the display; the
indicator light relative to the START/PAUSE
button will flash slowly green.
- Open the door. Load the laundry while making sure not to exceed the
maximum load quantity indicated in the wash cycle table.
- Pull out the detergent dispenser drawer and pour the detergent into the
relevant compartments, as described in the “DETERGENT DISPENSER
DRAWER” section.
- Close the door.
- Use the WASH CYCLE SELECTOR buttons to select the desired wash cycle:
the cycle’s name will appear on the display; the cycle will be associated
with a specific temperature and spin speed which can be modified. The
duration of the cycle will appear on the display.
- Modifying the temperature. The machine automatically select the
maximum temperature set for the selected wash cycle; this values cannot
therefore be increased. The temperature can be decreased by pressing
the TEMPERATURE button, until the cold wash “OFF” setting is reached. If
this button is pressed again, the maximum values are restored.
- Select the desired wash cycle.
- Select the desired options.
- Press the START/PAUSE
button to start the wash cycle; the relative indicator
light will light up steady green and the door will lock (
symbol on).
PAUSING A CYCLE
To pause the wash cycle, press the START/PAUSE
button again; the
indicator light will flash amber. To start the wash cycle from the point at
which it was interrupted, press the START/PAUSE
button again.
CHANGING A RUNNING WASH CYCLE
To change a wash cycle while it is in progress, pause the washing machine
using the START/PAUSE
button (the relative indicator light will flash amber),
then select the desired cycle and press the START/PAUSE
button again.
! To cancel a cycle that has already begun, press and hold the ON/OFF
button. The cycle will be stopped and the machine will switch off.
AT THE END OF THE WASH CYCLE
This will be indicated by the word “END OF CYCLE” on the display; when the
symbol switches off, the door may be opened. Open the door, unload the
laundry and switch off the machine. If you do not press ON/OFF button, the
washing machine will switch off automatically after about a half of an hour.
OPTIONS
- If the selected function is not compatible with the programmed wash
cycle, the indicator light will flash and the function will not be
activated.
- If the selected function is not compatible with another function which
has been selected previously, the indicator light corresponding to the
first function selected will flash and only the second function will be
activated; the indicator light corresponding to the enabled function
will remain lit.
Timer Saver
If you select this option, the wash cycle duration will be reduced by up to
50%, depending on the selected cycle, thereby guaranteeing simultaneous
water and energy saving. Use this cycle for lightly soiled garments.
Press this button to reduce the spin speed.
Eco
The Eco Wash function saves energy by not heating the water used to
wash your laundry – an advantage both to the environment and to your
energy bill. Instead, intensified wash action and water optimisation
ensure great wash results in the same average time of a standard cycle.
For the best washing results we recommend the usage of a liquid
detergent. By selecting the drying function as well, an automatic drying
cycle automatically activates at the end of the wash cycle – it too allows
for saving energy, thanks to the optimal combination of air temperature
and cycle duration; the display will visualise the “Eco” dryness level.
Delay timer
To set a delayed start for the selected programme, press the
corresponding button repeatedly until the required delay period has
been reached. When this option is enabled, the symbol lights up on
the display. To remove the delayed start function press the button until
the text “OFF” appears on the display.
Temperature
Each wash cycle has a pre-defined temperature. To modify the
temperature, press the “ “ button. The value will appear on the display.
Drying
The desired drying cycle type may be set by pressing the DRYING button
once or several times. Two options are available:
A - Based on the how damp the clothes are once they have been dried:
Iron: suitable for clothes which will need ironing afterwards. the
remaining dampness softens creases, making them easier to remove.
Hanger: ideal for clothes which do not need to be dried fully.
Cupboard: suitable for laundry which can be put back in a cupboard
without being ironed.
Extra: suitable for garments which need to be dried completely, such as
sponges and bathrobes.
B - Based on a set time period: between 30 and 180 minutes.
To exclude the drying phase press the relevant button until the text OFF
appears on the display.
If your laundry load to be washed and dried is much greater than the
maximum stated load, perform the wash cycle, and when the cycle is
complete, divide the garments into groups and put some of them back in the
drum. At this point, follow the instructions provided for a “Drying only” cycle.
Repeat this procedure for the remainder of the load. A cooling-down period
is always added to the end of each drying cycle.
Drying only
Use the cycle selector knob to select a drying cycle ( - - ) in
accordance with the type of fabric. The desired drying level or time may
also be set using the DRYING button
.
Selecting the cotton drying cycle through the programme selector
knob and pressing the “Eco Wash” button activates an automatic drying
cycle that allows for saving energy, thanks to an optimal combination
of air temperature and cycle duration; the display will visualise the “Eco”
dryness level.
Cleaning Action
Option “ ” makes it possible to optimise washing based on the level of
soil in the fabrics and on desired wash cycle intensity.
Select the wash programme: the cycle will be automatically set to “Normal”
as optimised for garments with an average level of soil (this setting is not
applicable to the “Wool” cycle, which is automatically set to “Delicate”).
For heavily-soiled garments press button “ ” until the “Super Wash”
level is reached. This level ensures a high-performance wash due to a
larger quantity of water used in the initial phase of the cycle and due to
increased drum rotation. It is useful when removing the most stubborn
stains. For lightly-soiled garments or a more delicate treatment of the
fabrics, press button “ ” until the “Delicate” level is reached.
The cycle will reduce the drum rotation to ensure washing results are
perfect for delicate garments.
Anti Allergy Rinse
Option “
” makes it possible to select the desired rinse type for sensitive
skin. Press the button once for the “Extra Rinse” level, which makes it
possible to select an additional rinse after the standard cycle rinse and
remove all traces of detergent. Press the button again for the “Sensitive
Skin” level, which makes it possible to select two additional rinses to the
standard cycle rinses; it is recommended for very sensitive skin. Press the
button for the third time for the “Anti allergy Rinse” level, which makes it
possible to select three additional rinses to the standard cycle rinses and
remove major allergens such as pollen, mites, cat and dog hair. Press the
button again to go back to the “Normal Rinse” rinse type. If the current
adjustment can be neither set nor changed, the display will show “Not
allowed”.
CHILD LOCK
to activate the control panel lock, press and hold the button for
approximately 2 seconds. When the symbol
is illuminated, the control
panel is locked. This means it is possible to prevent wash cycles from
being modified accidentally, especially where there are children in the
home. To deactivate the control panel lock, press and hold the button for
approximately 2 seconds.
TIPS AND SUGGESTIONS
Divide the laundry according to:
Type of fabric (cotton, mixed fibres, synthetics, wool, garments to be
hand-washed). Colour (separate coloured garments from whites, wash
new coloured garments separately). Delicates (small garments – such as
nylon stockings – and items with hooks – such as bras: insert them in a
fabric bag).
Empty the pockets:
Objects such as coins or lighters can damage the washer-dryer and the
drum. Check all buttons.
CARE AND MAINTENANCE
Before performing cleaning and maintenance, switch the washer-dryer off
and disconnect it from the mains power. Do not use flammable liquids to
clean the washer-dryer.
Cutting off the water and electricity supplies
Turn off the water tap after every wash cycle. This will limit wear on the
hydraulic system inside the washer-dryer and help to prevent leaks.
Unplug the washer-dryer when cleaning it and during all maintenance
work.
Cleaning the washer-dryer
The outer parts and rubber components of the appliance can be cleaned
using a soft cloth soaked in lukewarm soapy water. Do not use solvents or
abrasives.
The washer-dryer has a “Auto Clean” cycle for its internal parts; it must be
run without any load in the drum.
To help the wash cycle you may want to use either the detergent (i.e. a
quantity 10% the quantity specified for lightly-soiled garments) or special
additives to clean the washer-dryer. We recommend running a cleaning
programme every 40 wash cycles.
To start the programme press buttons “ ” and “
” simultaneously for
5 seconds.
The programme will start automatically and will last approximately 70
minutes. To stop the cycle press the START/PAUSE button.
Caring for the door and drum
Always leave the porthole door ajar in order to prevent unpleasant odours
from forming.
LOAD BALANCING SYSTEM
Before every spin cycle, to avoid excessive vibrations before every
spin and to distribute the load in a uniform manner, the drum rotates
continuously at a speed which is slightly greater than the washing
rotation speed. If, after several attempts, the load is not balanced
correctly, the machine spins at a reduced spin speed. If the load is
excessively unbalanced, the washer-dryer performs the distribution
process instead of spinning. To encourage improved load distribution and
balance, we recommend small and large garments are mixed in the load.
ACCESSORIES
Contact our Technical Assistance Service to check whether the following
accessories are available for this washer-dryer model.
Stacking kit
With this accessory you can secure the tumble dryer to the upper part of
your washer-dryer to save space and facilitate loading and unloading of
the tumble dryer.
TRANSPORT AND HANDLING
Do not lift the washer-dryer by gripping it from the upper section.
Unplug the appliance and close the water tap. Check that the door and
detergent dispenser drawer are tightly closed. Detach the filling hose
from the water tap then detach the drain hose. Empty all the water
remaining in the hoses and secure the latter so that they do not get
damaged during transport. Apply the transport bolts back on. Repeat, in
reverse order, the transport bolt removal procedure described in the
“Installation instructions”.
Important: Not emptying contents from pockets may cause pump or drain
blockages, or may damage the machine.
Do not wash items which do not have a wash label, or wash items that are
not intended as machine washable.
TROUBLESHOOTING
Your machine could occasionally fail to work. Before contacting the Technical Assistance Service, make sure that the problem cannot be easily solved using the following list.
Anomalies
Possible causes / Solution
The machine does not switch on.
The appliance is not plugged into the socket fully, or not enough to make contact.
There is no power to the socket, or the fuse has blown in the mains plug.
The door is not closed properly.
The ON/OFF
The wash cycle does not start.
button has not been pressed.
The START/PAUSE
button has not been pressed.
The water tap has not been turned on to allow water to flow into the machine.
A delayed start has been set.
The water inlet hose is kinked.
The water inlet hose is not connected to the water supply.
The washing machine does not fill with water
(“No Water, Check Supply” appears on the
display).
The water pressure is too low.
The water tap has not been turned on to allow water to flow into the machine.
There is no water supply to the house.
The inlet valve filter is blocked.
The START/PAUSE
button has not been pressed.
The top of the drain hose is too low - It must be fitted at a height between 65 and 100 cm from the floor.
The machine continuously fills with water and
continually drains away or Water left in the
drum or Stuck on wash.
The drain hose is connected incorrectly to the sink trap allowing water to run into the machine, the drain hose must be
positioned higher than the bottom of the sink to prevent water flowing down the drain hose.
The end of the drain hose has been pushed too far down the standpipe, the ‘U’ bracket should be fitted 100 mm from the end
of the drain hose.
The Pump filter is blocked.
The machine does not drain or spin - (error
lights flashing).
The drain hose is kinked.
New Installation - The blanking cap or spigot has not been removed if connected under a sink.
The drain hose or sink trap is blocked.
The machine does spin.
The ‘Spin’ Speed is set to “OFF”.
The machine does not heat or poor wash results.
The ‘Temperature’ is set to “OFF”.
The programme takes too long.
Programme times will vary due to water pressure, the incoming water temperature and if the wash load goes out of balance.
This will increase the programme times accordingly.
The Display sticks at one ‘time to end’ for more
than 1 Minute or the Display changes the
estimated ‘Time to End’ during the programme.
The display time is for guidance only - it is not a precise time to finish and may vary.
The feet have not been adjusted, enabling the machine to rock.
The washing machine vibrates a lot during the
spin cycle.
New Installation - Either the Transit Bolts including the plastic spacers, or the Polystyrene Packaging have not been removed
when installing the machine.
The machine is trapped between cabinets and/or walls.
The load is in a slight out of balance condition and machine is spinning, but at a lower speed.
The machine is noisy.
There will always be some motor, pump and drum noise during spin.
The dispenser drawer is blocked with detergent and requires cleaning.
The machine leaks from the
dispenser.
The water pressure is too high and requires turning down - turn down the tap on the water supply pipe slightly and try again.
The machine is tilting forwards - It must be level when in its final position.
The “Options” and START/PAUSE
indicator
lights flash rapidly and the display visualises an
error code (e.g.: F-01, F-...).
Switch off the machine and unplug it, wait for approximately 1 minute and then switch back on again. If the problem persists
contact Technical Assistance Centre.
The machine smells.
The machine requires a service wash. Run a auto clean wash cycle with detergent and no laundry.
The water level is too low when the machine is
washing.
The water level is correct if it can be seen at the bottom of the door.
There is too much foam.
The detergent is not suitable for machine washing (it should display the text
‘for washing machines’ or ‘hand and machine wash’ or the like).
General.
Your washing machine contains sensors that monitor progress during the wash cycle (eg: Water Levels, Temperatures, Out of Balance
loads, Wash time/progress). Normally, if your machine successfully completes the cycle, there is unlikely to be anything wrong!
The appliance is not plugged into the socket, or not enough to make contact.
There has been a power failure.
The washer-dryer does not dry.
The appliance door is not shut properly.
A Delay Timer has been set.
DRYING is in the OFF position.
DEMO MODE: to deactivate this function, switch the washing machine OFF. Than press and hold “Start/Pause”
“ON/OFF” button and hold both buttons for 2 seconds.
button, within 5 seconds press also
CLEANING THE DETERGENT DISPENSER
Remove the dispenser by raising it and
pulling it out (see figure).
Wash it under running water; this
operation should be repeated frequently.
1
2
CLEANING THE WATER FILTER / DRAINING RESIDUAL WATER
Switch off and unplug the washing machine before cleaning the water filter or draining residual water. If you used a hot
wash programme, wait until the water has cooled down before draining any water.
Clean the water filter regularly, to avoid that the water cannot drain after the wash due to obstruction of the filter.
If the water cannot drain, the display indicates that the water filter may be clogged.
1. Remove the kick panel: Using a screwdriver, do that which
is shown in the following figure.
4. Remove filter: Lay a cotton cloth beneath the water filter,
which can absorb a small amount of rest water. Then
remove the water filter by turning it out anticlockwise.
2. Container for the drained water:
Place a low and wide container under the water filter in
order to collect the residual water.
5. Clean the water filter: remove residues in the filter and
clean it under running water.
3. Drain the water:
Slowly turn the filter counter-clockwise until all the water
has come out. Allow the water to flow out without
removing the filter. Once the container is full, close the
water filter by turning it clockwise. Empty the container.
Repeat the procedure until all the water has been drained.
6. Insert the water filter and reinstall the plinth: Reinsert the water
filter again by turning it in clockwise direction. Make sure to turn
it in as far as it goes; the filter handle must be in vertical position.
To test water tightness of the water filter, you can pour about 1
liter of water into the detergent dispenser. Then reinstall the
plinth.
2
1
TRANSPORT AND HANDLING
Never lift the washing machine by holding it at the worktop.
1. Pull out the mains plug, and close the water tap.
2. Make sure that door and detergent dispenser are properly
closed.
3. Disconnect the inlet hose from the water tap, and remove
the drain hose from your draining point. Remove all rest
water from the hoses, and fix them so that they cannot get
damaged during transport.
4. Refit the transport bolts. Follow the instructions for
removing the transport bolts in the “Installation Guide” in
reverse order.
Important: Do not transport the washing machine without
having fixed the transport bolts.
AFTER-SALES SERVICE
BEFORE CALLING THE AFTER-SALES SERVICE
1. See if you can solve the problem by yourself with the help
of the suggestions given in the TROUBLESHOOTING
IF AFTER THE ABOVE CHECKS THE FAULT STILL
OCCURS, GET IN TOUCH WITH THE NEAREST
AFTER-SALES SERVICE
To receive assistance, call the number shown in page 9 or
follow the instructions on the website.
When contacting our Client After sales service, always specify:
• a brief description of the fault;
• the type and exact model of the appliance;
xxxxxxxxxxxx
2. Switch the appliance off and back on again to see if the
fault persists.
•
the service number (number after the word Service on the
rating plate).
• your full address;
• your telephone number.
If any repairs are required, please contact an authorised aftersales service (to guarantee that original spare parts will be used
and repairs carried out correctly).
Stickers with printed programs in local languages can be requested through Service Call. (Available languages: Swedish, Danish, Finnish and Norwegian)
DISTRIBUTION LINE AND CUSTOMER SERVICE INFORMATION
imported and exclusively marketed by:
10 mm - 0,39 inch
3.
2.
1.
150 ml
100 ml
50 ml
4.
2 cm - 0,7 inch
6.
5.
7.
8.
9.
max 0,5 cm
max 0,2 inch
10.
11.
12.
max 100 cm
39 inch
min 65 cm
25 inch
max 100 cm
39 inch
min 65 cm
25 inch
max 100 cm
39 inch
min 65 cm
25 inch
13.
14.
SAFETY INSTRUCTIONS
EN
IMPORTANT TO BE READ AND OBSERVE
used as specified by the fabric softener
instructions.
The final part of a tumble dryer cycle occurs
without heat (cool down cycle) to ensure that the
items are left at a temperature that ensures that
the items will not be damaged.
Never stop a tumble dryer before the end of
Very young children (0-3 years) should be kept the drying cycle unless all items are quickly
away from the appliance. Young children
removed and spread out so that the heat is
(3-8 years) should be kept away from the
dissipated.
appliance unless continuously supervised.
During the drying phase, the door tends to get
Children from 8 years old and above and persons
quite hot.
with reduced physical, sensory or mental
Do not use the appliance to dry clothes that
capabilities or lack of experience and knowledge
have been washed with flammable solvents (e.g.
can use this appliance only if they are supervised
trichlorethylene).
or have been given instructions on safe use and
Do not use the appliance to dry foam rubber or
understand the hazards involved. Children must
similar elastomers.
not play with the appliance. Cleaning and user
Make sure that the water tap is turned on
maintenance must not be carried out by children
during the drying cycles.
without supervision. Never open the door forcibly
Remove all objects from pockets such as
or use it as a step.
lighters and matches.
INSTALLATION
PERMITTED USE
The appliance must be handled and installed
CAUTION: The appliance is not intended to be
by two or more persons - risk of injury. Use
operated by means of an external switching
protective gloves to unpack and install - risk of
device, such as a timer, or separate remote
cuts.
controlled system.
If you want to stack a dryer on top of your
This appliance is intended to be used in
washing machine, first contact our After-Sales
household and similar applications such as: staff
Service or your specialist dealer to verify whether
kitchen areas in shops, offices and other working
this is possible. This is only possible if the dryer is
environments; farm houses; by clients in hotels,
attached to the washing machine by means of
motels, bed & breakfast and other residential
appropriate stacking kit available through our
environments.
After- Sales Service or your specialist dealer.
Do not load the machine above the maximum
Move the appliance without lifting it by the
capacity (kg of dry cloth) indicated in the
worktop or top lid.
programme table.
Installation, including water supply (if any) and
This appliance is not for professional use. Do
electrical
connections and repairs must be carried
not use the appliance outdoors.
out
by
a
qualified
technician. Do not repair or
Do not use any solvents (e.g. turpentine,
replace any part of the appliance unless
benzene), detergents containing solvents,
specifically stated in the user manual. Keep
scouring powder, glass or general purpose
children away from the installation site. After
cleaners, or flammable fluids; do not machine
wash fabrics that have been treated with solvents unpacking the appliance, make sure that it has not
been damaged during transport. In the event of
or flammable liquids.
problems, contact the dealer or your nearest
Do not dry unwashed items in the tumble
After-sales Service. Once installed, packaging
dryer.
waste (plastic, styrofoam parts etc.) must be
Items that have been soiled with substances
stored out of reach of children - risk of suffocation.
such as cooking oil, acetone, alcohol, petrol,
The appliance must be disconnected from the
kerosene, spot removers, turpentine, waxes and
wax removers should be washed in hot water with power supply before any installation operation risk of electric shock. During installation, make
an extra amount of detergent before being dried
sure the appliance does not damage the power
in the tumble dryer.
Items such as foam rubber (latex foam), shower cable - risk of fire or electric shock. Only activate
the appliance when the installation has been
caps, waterproof textiles, rubber backed articles
completed.
and clothes or pillows fitted with foam rubber
pads should not be dried in the tumble dryer.
Fabric softeners, or similar products, should be
Before using the appliance, read these safety instructions. Keep them nearby for future reference. These
instructions and the appliance itself provide important safety warnings, to be observed at all times.
The manufacturer declines any liability for failure to
observe these safety instructions, for inappropriate
use of the appliance or incorrect setting of controls.
Do not install your appliance where it may be
exposed to extreme conditions, such as: poor
ventilation, temperatures below 5 °C or above 35 °C.
When installing the appliance make sure that
the four feet are stable and resting on the floor,
adjusting them as required, and check that the
appliance is perfectly to level using a spirit level.
If the appliance is being installed on wood or
“floating” floors (certain parquet and laminate
materials), secure a 60 x 60 x 3 cm (at least) sheet
of plywood to the floor then place the appliance
on top of this.
Connect the water inlet hose(s) to the water
supply in accordance with the regulations of your
local water company.
For cold fill only models: do not connect to the
hot water supply.
For models with hot fill: the hot water inlet
temperature must not exceed 60 °C.
The washing machine is fitted with transport
bolts to prevent any possible damage to the
interior during transport. Before using the
machine, it is imperative that the transport bolts
are removed. After their removal, cover the
openings with the 4 enclosed plastic caps.
After installation of the device, wait a few
hours before starting it so that it acclimates to the
environmental conditions of the room.
Make sure that the ventilation openings in the
base of your washing machine (if available on
your model) are not obstructed by a carpet or
other material.
Use only new hoses to connect the appliance
to the water supply. The old hose-sets should not
be reused.
The supply water pressure must be in the 0.1-1
MPa range.
ELECTRICAL WARNINGS
It must be possible to disconnect the appliance
from the power supply by unplugging it if plug is
accessible, or by a multi-pole switch installed
upstream of the socket in accordance with the
wiring rules and the appliance must be earthed in
conformity with national electrical safety
standards.
Do not use extension leads, multiple sockets or
adapters. The electrical components must not be
accessible to the user after installation. Do not use
the appliance when you are wet or barefoot. Do
not operate this appliance if it has a damaged
power cable or plug, if it is not working properly,
or if it has been damaged or dropped.
If the supply cord is damaged, it must be
replaced with an identical one by the
manufacturer, its service agent or similarly
qualified persons in order to avoid a hazard - risk
of electric shock.
CLEANING AND MAINTENANCE
WARNING: Ensure that the appliance is
switched off and disconnected from the power
supply before performing any maintenance
operation; never use steam cleaning equipment risk of electric shock.
DISPOSAL OF PACKAGING MATERIALS
The packaging material is 100% recyclable and is marked with the
recycle symbol .
The various parts of the packaging must therefore be disposed of
responsibly and in full compliance with local authority regulations
governing waste disposal.
DISPOSAL OF HOUSEHOLD APPLIANCES
This appliance is manufactured with recyclable or reusable materials.
Dispose of it in accordance with local waste disposal regulations.
For further information on the treatment, recovery and recycling
of household electrical appliances, contact your local authority,
the collection service for household waste or the store where you
purchased the appliance. This appliance is marked in compliance
with European Directive 2012/19/EU, Waste Electrical and Electronic
Equipment (WEEE). By ensuring this product is disposed of correctly,
you will help prevent negative consequences for the environment and
human health.
The symbol on the product or on the accompanying documentation
indicates that it should not be treated as domestic waste but must be
taken to an appropriate collection center for the recycling of electrical
and electronic equipment.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising