Whirlpool | FWSG71283BV CS | Setup and user guide | Whirlpool FWSG71283BV CS Setup and user guide

Whirlpool FWSG71283BV CS Setup and user guide
EN
Quick guide
THANK YOU FOR BUYING A WHIRLPOOL PRODUCT.
In order to receive a more complete assistance,
please register your appliance on
www.whirlpool.eu/register
Before using the appliance carefully read the Safety Instruction.
Before using the machine, it is imperative that the transport bolts are removed. For more detailed
instructions on how to remove them, see the Installation Guide.
CONTROL PANEL
1
2
3
4
5
6
7
8
“ON/OFF” button
Programme selector
“Start/Pause” button
“Spin” button
“Intensive rinse” button
“Clean+” button
“Start delay” button
“FreshCare+” /
“Key lock“button
9 “Temperature” button
DISPLAY INDICATORS
Door locked
FreshCare+ activated
8
9
+1
+2
+3
3
2
Start delay activated
Key lock activated
Washing phase
Indicates washing phase of the cycle
Failure: Call Service
Refer to Troubleshooting section
Failure: Water filter clogged
Water cannot be drained; water filter
might be blocked
Failure: No water
No or not sufficient inlet water.
In the event of any failure, refer to the
“TROUBLESHOOTING” section
1
40°
60°
1
2
3 4 5
6 7
Programme
Temperatures
Default
Range
Recommended
detergent
Detergents and additives
Max. spin
speed
(rpm)
Max
load
(kg)
Duration
(Minutes)
Prewash
Main
wash
Softener
Powder Liquid
Total water lt
Max load 7 Kg
Power consumption in off-mode 0.5 W / in left-on mode 8 W
Residual
dampness % **
Energy
consumption
kWh
PROGRAMME CHART
Mixed
40°C
- 40°C
1000
3.5
***
–


–

–
–
–
White
60°C
- 90°C
1200
7.0
***
 (90°)




–
–
–
Cotton
40°C
- 60°C
1200
7.0
220
–




53
0,97
80
60°C
1200
7.0
260
–




53
0,90
52,5
40°C
1200
7.0
220
–




53
0,97
80
3.5
***
–


–

–
–
–
eCotton
60°C
Sport
40°C
- 40°C
600
- 30°C
Duvet
30°C
1000
2
***
–


–

–
–
–
Steam Refresh
–
–
–
1.5
***
–
–
–
–
–
–
–
–
Spin & Drain
–
–
1200
7.0
***
–
–
–
–
–
–
–
–
Rinse & Spin
–
–
1200
7.0
***
–
–

–
–
–
–
–
Rapid 30’
30°C
- 30°C
800
3
***
–


–

–
–
–
Colours 15°
15°C
15°C
1000
3.5
***
–


–

–
–
–
Wool
40°C
- 40°C
800
1.5
***
–


–

–
–
–
Delicates
30°C
- 30°C
–
1
***
–


–

–
–
–
Synthetics
40°C
- 60°C
1200
4
195
–




33
0,75
72
 Dosing required  Dosing optional
Cotton
- Test wash cycles in compliance with regulations 1061/2010
These are the reference programs for the energy label. Set this wash cycles with a
temperature of 40°C or 60°C. They are the most efficient programmes in terms of energy
and water consumption for washing normally soiled cotton laundry. The actual water
temperature may differ from the declared one.
For all Test Institutes
Long wash cycle for cottons: set wash cycle Cotton with a temperature of 40°C.
Synthetic program along: set wash cycle Synthetics with a temperature of 40°C.
This data may differ in your home due to changing conditions in inlet water
temperature, water pressure etc. Approximate programme duration values refer to the
default setting of the programmes, without options.
** After programme end and spinning with maximum selectable spin speed, in default
programme setting.
*** T
he duration of the programme is shown on the display.
6th Sense - the sensor technology adapts water, energy and programme duration to your
wash load.
PRODUCT DESCRIPTION
DETERGENT DISPENSER
1.
2.
3.
4.
5.
6.
7.
8.
Main wash compartment

Detergent for the main wash, stain remover
or water softener. For a liquid detergent it
A
B
is recommended to use removable plastic
partition A (supplied) for a proper dosage. If
powder detergent is used, place the partition
into slot B.
Prewash compartment
Detergent for the prewash.
Softener compartment
Fabric softener. Liquid starch.
Pour in softener or starch solution only up to the “max” mark.
Release button 
Press to remove tray for cleaning.
Worktop
Detergent dispenser
Control panel
Door handle
Door
Water filter - behind plinth
Plinth (removable)
Adjustable feet (4)
1.
2.
3.
4.
5.
6.
7.
8.
PROGRAMMES
FIRST TIME USE
For choosing the appropriate programme for your kind of
laundry, always respect the instructions on the care labels
of the laundry. The value given in the tub symbol is the
maximum temperature possible for washing the garment.
Mixed
For washing lightly to normally soiled resilient garments in cotton, linen,
synthetic fibres and mixed fibres.
White
For washing normally to heavily soiled towels, underwear, table and bed
linen, etc in resilient cotton and linen. Only when the temperature is
selected at 90°C the cycle is provided with a prewash phase before main
washing phase. In this case it is recommended to add detergent both, in
the prewash and main wash section.
Cotton
Normally to heavily soiled and robust cottons .
eCotton
For washing normally soiled cotton garments. At 40°c and 60°C, this is the
standard cotton programme and the most efficient in terms of water and
energy consumption.
Sport
For washing lightly soiled sports clothing (tracksuits, shorts, etc.). For best
results, we recommend not exceeding the maximum load indicated in
the ‚‘‘PROGRAMME CHART‘‘. We recommend using liquid detergent , and
adding the amount suitable for half-load.
Duvet
Designed for washing eiderdown padded items such as double or single
duvets, cushions and anoraks. It is recommended to load such padded
items in the drum with the edges folded inwards and not to exceed ¾ of
the drum’s volume. For optimal washing, we recommend using a liquid
detergent.
Steam Refresh
This programme refreshes garments by removing bad odours and
relaxing the fibres (1.5 kg, roughly 3 items). Insert dry items only (that are
not dirty) and select programme “Steam Refresh”. Garments will be a
little damp at the end of the cycle and can be worn after a few minutes.
The “Steam Refresh” programme makes ironing easier.
! Not recommended for wool or silk garments.
! Do not add softeners or detergents.
Spin & Drain
Spins the load then empties the water. For resilient garments. If you
exclude the spin cycle, the machine will drain only
Rinse & Spin
Rinses and then spins. For resilient garments.
Rapid 30’
For washing lightly soiled garments quickly. This cycle lasts only 30
minutes, saving time and energy.
Colours 15°
This cycle helps protect colours by washing in cold water (15°C) and uses
less energy to heat the water while still offering satisfactory wash results.
Suitable for lightly soiled, ustained garments. This cycle offers wash
results comparable to 40°c mixed at just 15°C
Wool
All wool garments can be washed using programme ‚“Wool“ even
those carryng the “hand-wash only “ label. For best results, use special
detergents and do not exceed max kg declaration of laundry.
Delicates
For washing particularly delicate garments. Preferably turn garments
inside out before washing.
Synthetics
For washing soiled garments made from synthetic fibres (such as
polyester, polyacrylic, viscose, etc.) or cotton/synthetic blends.
To remove any manufacturing debris select the “Cotton ” programme
at a temperature of 60°C. Pour a small quantity of detergent powder into
the main wash compartment of the detergent dispenser (maximum
1/3 of the quantity the detergent manufacturer recommends for lightly
soiled laundry). Start the programme without adding any laundry.
DAILY USE
Prepare your laundry according to the recommendations in the “HINTS
AND TIPS” section. Load the laundry, close the door, open the water tap
and press the “ON/OFF” button to switch the washing machine on, the
“Start/Pause”
button flashes. Turn the programme selector to the
desired programme and select any option if needed. The temperature
and spin speed can be changed by pressing the “Temperature”
button or the “Spin” button. Pull out the detergent dispenser and
add the detergent (and additives/softener) now. Observe the dosing
recommendations on the detergent pack. Then close the detergent
dispenser and press the “Start/Pause”
button. The “Start/Pause”
button will lights up and the door will be locked.
40°
60°
PAUSE A RUNNING PROGRAMME
To pause the wash cycle, press the “Start/Pause” ; the indicator light
will go off and the remaining time on display flash. To start the wash cycle
from the point at which it was interrupted press the button again.
OPEN THE DOOR, IF REQUIRED
After starting a programme, the “Door locked” indicator lights up to
show that the door can not be opened. As long as a wash programme is
running, the door remains locked. To open the door while a programme
is in progress, press the “Start/Pause”
to pause the programme.
Provided the water level and/or temperature is/are not too high, the
“Door locked” indicator light goes off and you can open the door.
For example to add or remove laundry. Press the “Start/Pause” button
again to continue the programme.
PROGRAMME END
The “Door locked” indicator light goes off and the display shows
“End”. To switch off the washing machine after programme ends press the
“ON/OFF” button, the lights goes off. If you do not press “ON/OFF”
button, the washing machine will switch off automatically after about
a half of an hour. Close the water tap, open the door and unload the
washing machine. Leave the door ajar to allow the drum to dry.
OPTIONS
! If the selected option is incompatible with the programme set,
the incompatibility will be signalled by a buzzer (3 beeps) and the
corresponding indicator light will flash.
! If the selected option is incompatible with another previously set
option, only the most recent selection will remain active.
Clean+
Clean+ is an option working on 3 different levels (Intensive, Daily
and Fast) that are specially designed to set the right washing action,
depending on your cleaning needs:
Intensive
: this option is designed for high levels of dirtiness,
removing most stubborn stains.
Daily
: this option is designed to remove everyday stains.
Fast
: this option is designed to remove lightly soiled stains.
Intensive rinse
By selecting this option, the efficiency of the rinse is increased and
optimal detergent removal is guaranteed. It is particularly useful for
sensitive skin. Press the button once, two or three times to select an
additional 1 +1 , 2 +2 or 3 +3 rinses after the standard cycle rinse and
remove all traces of detergent. Press the button again to go back to the
“Normal rinse” rinse type.
Start delay
To set the selected programme to start at a later time, press the button
to set the desired delay time. Symbol
lights on the display when this
fuction is enabled. To cancel the delayed start, press the button again
until the value ‚‘‘0‘‘ is shown on the display.
FreshCare+
This option enhances washing performance by generating steam
to inhibit the proliferation of the main bad odour sources inside the
machine. After steam phase, the washing machine will perform gentle
tumbling through slow rotations of the drum. FreshCare+ option starts
after the cycle ends for a maximum duration of 6h and you can interrupt
at any time by pressing any button on control panel or turning the knob.
(*) Wait around 5’ before open the door.
EN
Quick guide
Temperature
Every programme has a predefined temperature. If you want to change
the temperature, press the “Temperature”
button. The value appears
on the display.
Spin
Every programme has a predefined spin speed. If you want to change the
spin speed, press the “Spin” button. The value appears on the display.
Demo mode
This appliance is equipped with Demo mode function. For more
information see the USER MANUAL/ Demo Mode.
40°
60°
KEY LOCK
To lock the control panel, press and hold the “Key lock”
button for
approximately 3 seconds. The symbol
will light up on the display
to indicate that the control panel has been locked (with the exception
of the “ON/OFF“
button). This prevents unintentional changes to
programmes, especially with children near the machine. To unlock the
control panel, press and hold the “Key lock”
button for approximately
3 seconds .
BLEACHING
If you wish to bleach the laundry, load the washing machine and set the
“Rinse & Spin” programme.
Start the machine and wait for it to complete the first water filling cycle
(roughly 2 minutes). Put the machine in pause mode by pressing the
“Start/Pause”
button, open the detergent drawer and pour the bleach
(observe the recommended doses indicated on the package) into the
main wash compartment where the partition was previously mounted.
Restart the cycle by pressing the “Start/Pause”
button.
If desired, it is possible to add fabric softener into the appropriate
compartment of the detergent drawer.
HINTS AND TIPS
Sort your laundry according to
Type of fabric/care label (cotton, mixed fibres, synthetics, wool, handwash
items). Colour (separate coloured and white items, wash new coloured
items separately). Delicates (wash small items – like nylon stockings – and
items with hooks – like bras – in a cloth bag or pillow case with zip).
Empty all pockets
Objects like coins or lighters can damage your laundry as well as the
drum.
CLEANING & MAINTENANCE
For any cleaning and maintenance, switch off and unplug the washing
machine. Do not use flammable fluids to clean the washing machine.
Cleaning the outside of the washing machine
Use a soft damp cloth to clean the outer parts of the washing machine.
Do not use glass or general purpose cleaners, scouring powder or similar
to clean the control panel – these substances might damage the printing.
Checking the water supply hose
Check the inlet hose regularly for brittleness and cracks. If damaged,
replace it by a new hose available through our After-Sales Service or
your specialist dealer. Depending on the hose type: If the inlet hose has
a transparent coating, periodically check if the colour intensifies locally. If
yes, the hose may have a leak and should be replaced
Cleaning the mesh filters in the water supply hose
Close the tap and loosen the inlet hose on the tap. Clean the internal
mesh filter and screw the water inlet hose back onto the tap. Now
unscrew the inlet hose on the rear of the washing machine. Pull off the
mesh filter from the washing machine connection with universal pliers
and clean it. Refit the mesh filter and screw the inlet hose on again. Turn
on the tap and ensure that the connections are completely water-tight.
Cleaning the water filter / draining residual water
If you used a hot wash programme, wait until the water has cooled down
before draining any water. Clean the water filter regularly, to avoid that the
water cannot drain after the wash due to obstruction of the filter. If the water
cannot drain, the display indicates that the water filter may be clogged.
Remove the plinth by using the screwdriver: push downwards one side
of the plinth with your hand, then push the screwdriver into the gap between plinth and front panel and pry open the plinth. Place a broad, flat
container beneath the water filter, to collect the drain water. Slowly turn
the filter counterclockwise until water flows out. Let the water flow out,
without removing the filter. When the container is full, close the water
filter by turning it in clockwise. Empty the container. Repeat this procedure until all the water has drained. Lay a cotton cloth beneath the water
filter, which can absorb a small amount of rest water. Then remove the
water filter by turning it out anti clockwise. Clean the water filter: remove
residues in the filter and clean it under running water. Insert the water
filter and reinstall the plinth: Reinsert the water filter again by turning it
in clockwise direction.
Make sure to turn it in as far as it goes; the filter handle must be in vertical
position. To test water tightness of the water filter, you can pour about 1
liter of water into the detergent dispenser. Then reinstall the plinth.
ACCESSORIES
Contact our After-Sales Service to check if the following accessories are
available for your washing machine model.
Stacking kit shelf
By which your dryer can be fixed on top of your washing machine to save
space and to facilitate loading and unloading your dryer in the higher
position.
TRANSPORT AND HANDLING
Never lift the washing machine by holding it at the worktop.
Pull out the mains plug, and close the water tap. Make sure that door
and detergent dispenser are properly closed. Disconnect the inlet hose
from the water tap, and remove the drain hose from your draining point.
Remove all rest water from the hoses, and fix them so that they cannot
get damaged during transport. Refit the transport bolts. Follow the
instructions for removing the transport bolts in the INSTALLATION GUIDE
in reverse order.
TROUBLESHOOTING
The washing machine may sometimes not work properly for certain reasons. Before calling the After-sales service, it is recommended to check to see if
the problem can be easily resolved using the following list.
Anomalies:
Possible causes / Solution:
The washing machine does not turn on.
•
•
The plug is not inserted into the electrical outlet, or not enough to make contact.
There has been a power failure.
The wash cycle does not start.
•
•
•
•
•
The door is not fully closed.
The “ON/OFF” button has not been pressed.
The “Start/Pause”
button has not been pressed.
The water tap is not open.
A “Start delay” has been set.
The washing machine does not fill with
water (the message “h2o” is shown on
the display). “Beep” sound every 5
seconds.
•
•
•
•
•
•
The water intake hose is not connected to the tap.
The hose is bent.
The water tap is not open.
The mains water supply has been shut off.
There is not enough pressure.
The “Start/Pause”
button has not been pressed.
•
•
•
•
The drain hose has not been installed at 65 to 100 cm from the ground.
The end of the drain hose is immersed in water.
The drain connector on the wall does not have an air vent.
If the problem persists after having performed these checks, close the water tap, shut off the
washing machine, and call the After-sales service. If the dwelling is located on one of the
uppermost floors of a building, a siphon effect can sometimes occur, thus causing the washing
machine to load and drain water continuously. Special anti-siphon valves are available on the
market to prevent these types of problems.
The washing machine loads and drains
water continuously.
•
The washing machine does not drain or
does not spin.
•
•
The programme does not include the draining function: with certain programmes it must be
activated manually.
The drain hose is bent.
The drain line is obstructed.
The washing machine vibrates
excessively during the spin cycle.
•
•
•
At the time of installation, the drum was not properly unblocked.
The washing machine is not level.
The washing machine is squeezed between furniture and the wall.
The washing machine leaks water.
•
•
•
The water intake hose has not been tightened properly.
The detergent dispenser is clogged.
The drain hose has not been properly fastened.
•
Shut off the machine, disconnect the plug from the outlet, and wait about 1 minute before
turning it back on.
If the problem persists, call the After-sales service.
The machine is locked and the display
flashes, indicating an error code (e.g.
F-01, F-..).
Too much foam is formed.
Door is locked, with or without
failure indication, and the
programme does not run.
•
•
•
•
•
The detergent is not compatible with the washing machine (it must bear the wording “for
washing machines”, “for hand washing and washing machines”, or something similar).
The dosage was excessive.
Door is locked in case of power breakdown. Programme will continue automatically as soon as
the mains is available again.
Washing machine is in a standstill. Programme will continue automatically after the origin of
the standstill does not persist anymore.
You can download the H&S INSTRUCTIONS, USER MANUAL, PRODUCT FICHE and ENERGY DATA by:
• Visiting our website - http://docs.whirlpool.eu
• Using QR code
• Alternatively, contact our After‑sales Service (See phone number in the warranty booklet). When
contacting our After‑sales Service, please state the codes provided on your product’s identification plate.
xxxxxxxxxxxx
195160650.00
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising