Hotpoint | UH8 F2D WI | Setup and user guide | Hotpoint UH8 F2D WI Setup and user guide

Hotpoint UH8 F2D WI Setup and user guide
QUICK START GUIDE
SMART DISPLAY
This optional function can be used to save energy. To activate the Smart
Display, press the buttons and together for 3 seconds until an
audible signal sounds.
To deactivate this function repeat the same procedure.
Remember that this function does not disconnect the appliance from the
power supply, but only reduce the power consumed by external display
(see the Instructions for Use).
2
3
10
4
FAST FREEZE button
The use of this function is recommended when placing a very high quantity of food to be
frozen in the freezer compartment.
24 hours before freezing fresh food, press & hold for 3 sec. the Freezer button to activate
the Fast Freeze function.
When activated, the Fast Freeze indication will be displayed by the Freezer Temperature
LEDs as shown in beside sequence.
After 24 hours place the food to be frozen in the upper basket of freezer compartment.
The function is automatically disabled after about 50 hours, or can be manually disabled
by pressing Freezer °C button.
5
6
FAST FREEZE indicator (see the Instructions for Use).
7
11
ON/STANDBY indicator /button
To put the product in Stand-by, press and hold for 3 seconds. All the icons
turn off except On/Standby indicator . To reactivate the appliance press
once (briefly) this button.
8
9
12
BLACK OUT ALARM
Long Black-out Alarm indicator. (see the Instructions for Use)
TEMPERATURE DISPLAY
1. Control panel
2. Light (LED system)
3. Ice packs*
4. Ice Mate* or Ice tray*
5. Drawer divider*
6. Bottle rack*
7. Glass shelves
8. Rating plate with commercial name
9. Door reversibility kit
10. Area for freezing fresh food or to store
frozen food
11. Area for storing frozen foods
12. Door seal
TEMPERATURE SETTING button
The appliance is normally factory-set for operation at the recommended
temperature of -18°C. The internal temperature can be adjusted between
-16°C and -24°C, proceeding as follows:
• Press to change the set point (°C). The storage temperature can be
changed by -1°C with each pressure of the button: the value changes
cyclically between -16°C and -24°C.
HOW TO REVERSE DOOR SWING
- see enclosed Instructions for Use (Version_1)
Is recommended to reverse door swing by two
persons.
There is not foreseen door reversibility for:
- models with integrated handle
- models with glass panel on the door.
Specifications, technical data and images
may vary from model to model.
To receive the assistance call the number shown
on the warranty booklet or follow the instruction
on the web site www.hotpoint.eu
PARTY MODE button
Press to activate/deactivate the Party Mode function. Use this function to chill drinks
inside the freezer compartment.
Important: do not leave the bottle inside the freezer compartment longer than the
function is active (30 minutes).
PARTY MODE indicator (see the Instructions for Use).
FREEZE CONTROL
Freeze Control is an advanced technology that reduces freeze burns and
food preserves its original quality and color.
* Available on selected models
HOW TO START THE APPLIANCE
After plugging the appliance to the mains, it starts
the operation automatically. After starting the
appliance, wait at least 4-6 hours before placing food
into the appliance. When the appliance is connected
to the power supply, the display lights up and all
the icons appear on the display for approximately 1
second.
The default (factory) values of the freezer
compartment settings light-up.
STOP ALARM button
Press in case of alarm (see the below Alarm Table).
ALARMS TABLE
ALARMS TYPE
Signal
Door open alarm
The acoustical alarm is activated and the Alarm Indicator
Temperature alarm
The Temperature display blinks (°C) and the Alarm Indicator
Party Mode Alarm
The Party Mode Indicator
Long Black-Out alarm
Malfunction
FR
GB
PT
Cause
Cure
The door has remained open for more than 2 minutes.
Close the door or press the Stop Alarm to mute the acoustical alarm.
The inside temperature is not adequate.
Press the Stop Alarm button ; the acoustical alarm stops, the Temperature Display (°C)
remains on until a temperature < -10°C is reached.
blinks and the Alarm Indicator
30 min. elapsed since Party Mode function has been activated. It is time to take out the
bottle from the freezer ( see Instructions for Use for more details).
Press the Stop Alarm button
remains on, the Alarm indicator
blinks and the
The Black Out Alarm icon
Temperature display (°C) blinks, showing the maximum temperature reached during
blackout.
Prolonged power failure, able to cause the inside temperature to increase to 0°C.
Press the Stop Alarm button ; the acoustical alarm stops, the Temperature Display (°C)
remains on until a temperature < -10°C is reached.
blinks and the Alarm Indicator
The letter “F” blinks on the display (°C).
Product malfunction.
Contact the After-sales Service.
blinks.
remains on.
blinks and the acoustical alarm is activated.
and remove the bottle from the freezer.
Printed in Italy
1
01/17 - Whirlpool® Registered trademark/TM Trademark of Whirlpool group of companies - © Copyright Whirlpool Europe s.r.l. 2014. All rights reserved - http://www.whirlpool.eu
Read the Instructions for Use carefully before
using the appliance.
EN
19515044800
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising