Zanussi | ZCG61036XA | User manual | ZANUSSI ZCG61036XA User Manual

ZANUSSI ZCG61036XA User Manual
User Manual
GETTING
STARTED?
EASY.
ZCG61036XA
EN User Manual
Cooker
MA
SAFETY INFORMATION
Before the installation and use of the appliance, carefully read the
supplied instructions. The manufacturer is not responsible for any
injuries or damages that are the result of incorrect installation or
usage. Always keep the instructions in a safe and accessible
location for future reference.
CHILDREN AND VULNERABLE PEOPLE SAFETY
WARNING!
Risk of suffocation, injury or permanent disability.
•
•
•
•
•
•
•
This appliance can be used by children aged from 8 years and
above and persons with reduced physical, sensory or mental
capabilities or lack of experience and knowledge if they have
been given supervision or instruction concerning the use of the
appliance in a safe way and understand the hazards involved.
Children between 3 and 8 years of age and persons with very
extensive and complex disabilities shall be kept away unless
continuously supervised.
Children of less than 3 years of age should be kept away
unless continuously supervised.
Do not let children play with the appliance.
Keep all packaging away from children and dispose of it
appropriately.
Keep children and pets away from the appliance when it
operates or when it cools down. Accessible parts are hot.
Children shall not carry out cleaning and user maintenance of
the appliance without supervision.
GENERAL SAFETY
•
•
•
2
Only a qualified person must install this appliance and replace
the cable.
This appliance is intended for use up to an altitude of 2000 m
above sea level.
This appliance is not intended to be used on a ships, boats or
vessels.
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
Do not install the appliance behind a decorative door in order to
avoid overheating.
Do not install the appliance on a platform.
Do not operate the appliance by means of an external timer or
separate remote-control system.
WARNING: Unattended cooking on a hob with fat or oil can be
dangerous and may result in fire.
NEVER try to extinguish a fire with water, but switch off the
appliance and then cover flame e.g. with a lid or a fire blanket.
CAUTION: The cooking process has to be supervised. A short
term cooking process has to be supervised continuously.
WARNING: Danger of fire: Do not store items on the cooking
surfaces.
Do not use a steam cleaner to clean the appliance.
Do not use harsh abrasive cleaners or sharp metal scrapers to
clean the glass door or the glass of hinged lids of the hob since
they can scratch the surface, which may result in shattering of
the glass.
Metallic objects such as knives, forks, spoons and lids should
not be placed on the hob surface since they can get hot.
Remove any spillage from the lid before opening. Let the hob
surface cool down before closing the lid.
WARNING: The appliance and its accessible parts become hot
during use. Care should be taken to avoid touching heating
elements.
Always use oven gloves to remove or put in accessories or
ovenware.
Before maintenance cut the power supply.
Ensure that the appliance is switched off before replacing the
lamp to avoid the possibility of electric shock.
If the mains power supply cable is damaged, it must be
replaced by the manufacturer, its Authorised Service Centre or
similarly qualified persons to avoid an electrical hazard.
WARNING: Use only hob guards designed by the manufacturer
of the cooking appliance or indicated by the manufacturer of
the appliance in the instructions for use as suitable or hob
3
guards incorporated in the appliance. The use of inappropriate
guards can cause accidents.
SAFETY INSTRUCTIONS
This appliance is suitable for the following markets:
•
MA
INSTALLATION
WARNING! Only a qualified person
must install this appliance.
•
•
•
•
•
•
•
•
•
•
•
Remove all the packaging.
Do not install or use a damaged appliance.
Follow the installation instructions supplied with
the appliance.
Always take care when moving the appliance as
it is heavy. Always use safety gloves and
enclosed footwear.
Do not pull the appliance by the handle.
The kitchen cabinet and the recess must have
suitable dimensions.
Keep the minimum distance from other
appliances and units.
Make sure that the appliance is installed below
and adjacent safe structures.
Parts of the appliance carry current. Close the
appliance with furniture to prevent touching the
dangerous parts.
The sides of the appliance must stay adjacent to
appliances or units with the same height.
Do not install the appliance adjacent to a door
or under a window. This prevents hot cookware
to fall from the appliance when the door or the
window is opened.
ELECTRICAL CONNECTION
WARNING! Risk of fire and electric
shock.
•
•
•
•
•
•
4
All electrical connections should be made by a
qualified electrician.
The appliance must be earthed.
Make sure that the parameters on the rating
plate are compatible with the electrical ratings
of the mains power supply.
Always use a correctly installed shockproof
socket.
Do not use multi-plug adapters and extension
cables.
Do not let mains cables touch or come near the
appliance door, especially when the door is hot.
•
•
•
•
•
•
The shock protection of live and insulated parts
must be fastened in such a way that it cannot be
removed without tools.
Connect the mains plug to the mains socket
only at the end of the installation. Make sure that
there is access to the mains plug after the
installation.
If the mains socket is loose, do not connect the
mains plug.
Do not pull the mains cable to disconnect the
appliance. Always pull the mains plug.
Use only correct isolation devices: line
protecting cut-outs, fuses (screw type fuses
removed from the holder), earth leakage trips
and contactors.
The electrical installation must have an isolation
device which lets you disconnect the appliance
from the mains at all poles. The isolation device
must have a contact opening width of minimum
3 mm.
Fully close the appliance door, before you
connect the mains plug to the mains socket.
GAS CONNECTION
• All gas connections should be made by a
qualified person.
• Before installation, make sure that the local
distribution conditions (nature of the gas and
gas pressure) and the adjustment of the
appliance are compatible.
• Make sure that there is air circulation around the
appliance.
• The information about the gas supply is on the
rating plate.
• This appliance is not connected to a device,
which evacuates the products of combustion.
Make sure to connect the appliance according
to current installation regulations. Pay attention
to requirements regarding adequate ventilation.
USE
WARNING! Risk of injury and burns.
Risk of electrical shock.
•
•
•
This appliance is for household use only.
Do not change the specification of this
appliance.
Make sure that the ventilation openings are not
blocked.
•
•
•
•
•
Do not let the appliance stay unattended during
operation.
Deactivate the appliance after each use.
Be careful when you open the appliance door
while the appliance is in operation. Hot air can
release.
Do not operate the appliance with wet hands or
when it has contact with water.
Do not use the appliance as a work surface or
as a storage surface.
•
•
•
•
WARNING! Risk of fire and explosion
•
•
•
•
•
•
•
Fats and oil when heated can release flammable
vapours. Keep flames or heated objects away
from fats and oils when you cook with them.
The vapours that very hot oil releases can cause
spontaneous combustion.
Used oil, that can contain food remnants, can
cause fire at a lower temperature than oil used
for the first time.
Do not put flammable products or items that are
wet with flammable products in, near or on the
appliance.
Do not let sparks or open flames to come in
contact with the appliance when you open the
door.
Open the appliance door carefully. The use of
ingredients with alcohol can cause a mixture of
alcohol and air.
WARNING! Risk of damage to the
appliance.
•
•
•
•
•
•
•
•
To prevent damage or discoloration to the
enamel:
– do not put ovenware or other objects in the
appliance directly on the bottom.
– do not put water directly into the hot
appliance.
– do not keep moist dishes and food in the
appliance after you finish the cooking.
– be careful when you remove or install the
accessories.
Discoloration of the enamel or stainless steel
has no effect on the performance of the
appliance.
Use a deep pan for moist cakes. Fruit juices
cause stains that can be permanent.
Do not keep hot cookware on the control panel.
Do not let cookware boil dry.
Be careful not to let objects or cookware fall on
the appliance. The surface can be damaged.
Do not activate the cooking zones with empty
cookware or without cookware.
Do not put aluminium foil on the appliance or
directly on the bottom of the appliance.
•
•
Cookware made of cast iron, aluminium or with
a damaged bottom can cause scratches.
Always lift these objects up when you have to
move them on the cooking surface.
Provide good ventilation in the room where the
appliance is installed.
Use only stable cookware with the correct
shape and diameter larger than the dimensions
of the burners.
Make sure the flame does not go out when you
quickly turn the knob from the maximum to the
minimum position.
Use only the accessories supplied with the
appliance.
Do not install a flame diffuser on the burner.
This appliance is for cooking purposes only. It
must not be used for other purposes, for
example room heating.
CARE AND CLEANING
WARNING! Risk of injury, fire, or
damage to the appliance.
•
•
•
•
•
•
•
•
•
•
Before maintenance, deactivate the appliance.
Disconnect the mains plug from the mains
socket.
Make sure the appliance is cold. There is the
risk that the glass panels can break.
Replace immediately the door glass panels
when they are damaged. Contact the
Authorised Service Centre.
Be careful when you remove the door from the
appliance. The door is heavy!
Fat and food remaining in the appliance can
cause fire.
Clean regularly the appliance to prevent the
deterioration of the surface material.
Clean the appliance with a moist soft cloth. Only
use neutral detergents. Do not use any abrasive
products, abrasive cleaning pads, solvents or
metal objects.
If you use an oven spray, obey the safety
instructions on the packaging.
Do not clean the catalytic enamel (if applicable)
with any kind of detergent.
Do not clean the burners in the dishwasher.
LID
• Do not change the specification of the lid.
• Clean the lid regularly.
• Do not open the lid, when there are spills on the
surface.
• Before you close the lid turn all burners off.
• Do not close the lid until the hob and oven are
completely cold.
5
•
•
•
Glass lid can shatter, when heated (if
applicable).
•
•
Keep the lid glass open, while the oven is in
operation (if applicable).
SERVICE
• To repair the appliance contact an Authorised
Service Centre.
• Use original spare parts only.
DISPOSAL
INTERNAL LIGHTING
WARNING! Risk of injury or
suffocation.
WARNING! Risk of electric shock.
•
•
•
Do not leave the appliance unattended during
grilling. Accessible parts become hot.
Keep children away when the grill is in use.
Do not put the oven shelf with food on the
highest shelf level.
The type of light bulb or halogen lamp used for
this appliance is for household appliances only.
Do not use it for house lighting.
Before replacing the lamp, disconnect the
appliance from the power supply.
Only use lamps with the same specifications.
GAS GRILL
•
•
•
•
•
Contact your municipal authority for information
on how to discard the appliance correctly.
Disconnect the appliance from the mains
supply.
Cut off the mains electrical cable close to the
appliance and dispose of it.
Remove the door catch to prevent children or
pets from becoming trapped in the appliance.
Flat the external gas pipes.
WARNING! Risk of fire, explosion and
burns.
PRODUCT DESCRIPTION
GENERAL OVERVIEW
1
2
3
4
5
7
6
5
4
3
2
1
6
7
1 Button for the spark generator
2 Knob for the heating functions
3 Button for the lamp
4 Knobs for the hob
5 Grill
6 Lamp
7 Shelf positions
COOKING SURFACE LAYOUT
1
2
3
1 Auxiliary burner
2 Steam outlet - number and position depend on
the model
3 Semi-rapid burner
4 Semi-rapid burner
5 Rapid burner
5
4
ACCESSORIES
• Wire shelf
For cookware, cake tins, roasts.
•
Baking tray
For cakes and biscuits.
BEFORE FIRST USE
WARNING! Refer to Safety chapters.
INITIAL CLEANING
Remove all accessories from the oven.
Refer to "Care and cleaning" chapter.
Clean the oven and the accessories before first
use.
Put the accessories back to their initial position.
PREHEATING
Preheat the empty appliance to burn off the
remaining grease.
1. Set the oven function knob to maximum gas
.
flow position
Refer to "Oven - Daily use" chapter.
2. Let the appliance operate for approximately 1
hour.
WARNING! Accessories can become
hotter than usual.
The appliance can emit an odour and smoke. This
is normal. Make sure that the airflow is sufficient.
Let the oven cool down. Dampen a soft cloth with
warm water and a little mild washing-up liquid and
use this to clean the oven cavity.
HOB - DAILY USE
WARNING! Refer to Safety chapters.
IGNITION OF THE HOB BURNER
WARNING! Be very careful when you
use open fire in the kitchen
environment. The manufacturer
declines any responsibility in case of
the flame misuse.
Always light the burner before you put
on the cookware.
7
If the burner accidentally goes out,
turn the knob to the off position and try
to light the burner again after minimum
1 minute.
The spark generator can start
automatically when you switch on the
mains, after installation or a power cut.
It is normal.
In the absence of electricity you can
ignite the burner manually.
BURNER OVERVIEW
Ignition of a hob burner with the
thermocouple
• For manual ignition put the flame near the
burner. Push the knob for the hob down and
turn it counterclockwise to the maximum gas
A
flow position
.
For ignition with spark generator button push
B
•
and hold the spark generator button
. At the
same time push the knob for the hob down and
turn it counterclockwise to the maximum gas
flow position
. Release the spark generator
button when burner lights.
Keep the knob for the hob pushed for equal or less
than 10 seconds to let the thermocouple warm up.
If not, the gas supply is interrupted.
Adjust the flame after it is regular.
WARNING! Do not keep the knob
pushed for more than 15 seconds. If
the burner does not light after 15
seconds, release the knob, turn it into
the off position and try to light the
burner again after minimum 1 minute.
If after some tries the burner does not
light, check if the crown and its cap
are in the correct position.
C
D
A.
B.
C.
D.
Burner cap
Burner crown
Ignition candle
Thermocouple (if applicable)
TURNING THE BURNER OFF
To put the flame out, turn the knob to the off
position
.
WARNING! Always turn the flame
down or switch it off before you
remove the pans from the burner.
HOB - HINTS AND TIPS
WARNING! Refer to Safety chapters.
COOKWARE
WARNING! Do not put the same pan
on two burners.
WARNING! Do not put unstable or
damaged pots on the burner to
prevent spills and injuries.
8
CAUTION! Make sure that pot
handles are not above the front edge
of the cooktop.
CAUTION! Make sure that the pots
are placed centrally on the burner in
order to get the maximum stability and
a lower gas consumption.
DIAMETERS OF COOKWARE
WARNING! Use cookware with
diameters applicable to the size of
burners.
Burner
Diameter of cookware
(mm)
Rapid
160 - 260
Semi-rapid
140 - 240
Auxiliary
120 - 180
ENERGY SAVING
• If it is possible, always put the lids on the
cookware.
• When the liquid starts to boil, turn down the
flame to barely simmer the liquid.
HOB - CARE AND CLEANING
WARNING! Refer to Safety chapters.
GENERAL INFORMATION
• Clean the hob after each use.
• Always use cookware with a clean base.
• Scratches or dark stains on the surface have no
effect on how the hob operates.
• Use a special cleaner suitable for the surface of
the hob.
• Wash stainless steel parts with water, and then
dry them with a soft cloth.
CLEANING THE HOB
• Remove immediately: melted plastic, plastic
foil, sugar and food with sugar, otherwise, the
dirt can cause damage to the hob. Take care to
avoid burns.
• Remove when the hob is sufficiently cool:
limescale rings, water rings, fat stains, shiny
metallic discoloration. Clean the hob with a
moist cloth and a non-abrasive detergent. After
cleaning, wipe the hob dry with a soft cloth.
• To clean the enamelled parts, caps and crowns,
wash them with warm soapy water and dry them
carefully before you put them back on.
CLEANING THE SPARK PLUG
This feature is obtained through a ceramic ignition
candle with a metal electrode. Keep these
components well clean to prevent difficult lighting
and check that the burner crown holes are not
obstructed.
PAN SUPPORTS
The pan supports are not resistant to
washing in a dishwasher. They must
be washed by hand.
1. Remove the pan supports to easily clean the
hob.
Be very careful when you replace
the pan supports to prevent the
hob top from damage.
2. The enamel coating occasionally can have
rough edges, so be careful when you wash the
pan supports by hand and dry them. If
necessary, remove stubborn stains with a paste
cleaner.
3. After you clean the pan supports, make sure
that they are in correct positions.
4. For the burner to operate correctly, make sure
that the arms of the pan supports are aligned
with the centre of the burner.
PERIODIC MAINTENANCE
Speak to your local Authorised Service Centre
periodically to check the conditions of the gas
supply pipe and the pressure adjuster, if fitted.
OVEN - DAILY USE
WARNING! Refer to Safety chapters.
9
OVEN FUNCTIONS
Oven function
Application
Off position
The oven is off.
Maximum gas supply
To adjust the oven temperature - highest setting.
Minimum gas supply
To adjust the oven temperature - lowest setting.
Grilling
To grill flat food in the middle of the grill. To make
toast.
Oven lamp
To illuminate the oven interior.
To use this function, press the button for the lamp.
MANUAL IGNITION OF OVEN GAS BURNER
Oven safety device:
The gas oven has a thermocouple. It
stops the gas flow if the flame goes
out.
1. Open the oven door.
2. Hold the flame near the hole in the bottom of
the oven cavity.
AFTER IGNITING THE OVEN GAS BURNER
1. Release the knob for the oven functions.
2. Close the oven door.
3. Turn the knob for the oven functions to set the
necessary heat setting.
Control the flame trough the holes in the bottom of
the oven.
TURNING OFF THE OVEN BURNER
To put out the flame, turn the knob to the off
position
.
USING THE GRILL
CAUTION! Always keep the appliance
door closed when the grill operates.
3. At the same time push the knob for the oven
functions and turn it counterclockwise to the
maximum gas flow position.
4. When the flame comes on, keep the knob for
the oven functions pushed on the maximum gas
flow position for 15 seconds or less to let the
thermocouple warm up.
Do not keep the knob for the oven
functions pushed for more than 15
seconds. If the oven burner does not
light after 15 seconds, release the
knob for the oven functions, turn it into
off position, open the oven door and
try to light the oven burner again after
minimum 1 minute.
10
The grill temperature cannot be
adjusted. To get a lower temperature
or slower cooking time, lower the grill
pan away from the flame.
Do not put the meat directly on the
tray or pan.
CAUTION! Do not put the meat on
the highest shelf level. There is a risk
of fire.
CAUTION! Make sure to turn the knob
for the oven funstions as far as it goes.
Avoid the intermediary position
between Off and Grill. On the
intermediary positions the spark
generator can remain active.
1. Open the oven door.
2. Ignite the grill burner.
• For manual ignition hold a flame near the
grill burner holes. Push and turn the knob
for the grill to the flame position. Hold the
knob pushed down.
3. Hold the knob for the grill pushed for
approximately 15 seconds.
4. Release the oven control knob.
If the grill does not come on or if it accidentally
goes out release the knob for the oven
functions and turn it to the Off position. Open
the oven door. After one minute, try to light the
grill again.
5. Preheat the grill for 5 to 10 minutes.
6. Put the oven shelf with the meat on shelf
position 3.
7. Put a baking tray or roasting pan below, on
shelf position 2, to collect the juices.
TURNING OFF THE GRILL BURNER
To put out the flame, turn the knob to the off
position
.
OVEN - USING THE ACCESSORIES
WARNING! Refer to Safety chapters.
Do not push the baking tray all the way
to the back wall of the cavity. This
prevents the heat from circulating
around the tray. The food may be
burnt, especially in the rear part of the
tray.
INSERTING THE ACCESSORIES
Wire shelf:
Put the shelf on the correct shelf position. Make
sure it does not touch the back wall of the oven.
Tray:
Put the tray or deep pan on the shelf position. Make
sure it does not touch the back wall of the oven.
OVEN - HINTS AND TIPS
WARNING! Refer to Safety chapters.
•
The temperature and baking times in
the tables are guidelines only. They
depend on the recipes and the quality
and quantity of the ingredients used.
GENERAL INFORMATION
• The appliance has five shelf positions. Count
the shelf positions from the bottom of the
appliance floor.
• Moisture can condense in the appliance or on
the door glass panels. This is normal. Always
stand back from the appliance when you open
the appliance door while cooking. To decrease
•
the condensation, operate the appliance for 10
minutes before cooking.
Clean the moisture after each use of the
appliance.
Do not put the objects directly on the appliance
floor and do not put aluminium foil on the
components when you cook. This can change
the baking results and cause damage to the
enamel.
BAKING
• Your oven may bake or roast differently to the
oven you had before. Adapt your usual settings
such as temperature, cooking time and shelf
position to the values in the tables.
• Use the lower temperature the first time.
11
•
•
•
If you cannot find the settings for a special
recipe, look for the similar one.
Cakes and pastries at different heights do not
always brown equally at first. If this occurs, do
not change the temperature setting. The
differences equalize during the baking
procedure.
Trays in the oven can twist during baking. When
the trays become cold again, the distortions
disappear.
Initially, monitor the performance when you cook.
Find the best settings (heat setting, cooking time,
etc.) for your cookware, recipes and quantities
when you use this appliance.
COOKING TABLES
To set the desired temperature turn the knob for the
oven to the appropriate position.
BAKING CAKES
Do not open the oven door before 3/4 of the set
cooking time is up.
COOKING MEAT AND FISH
Leave the meat for approximately 15 minutes before
carving so that the juice does not seep out.
To prevent too much smoke in the oven during
roasting, add some water into the deep pan. To
prevent the smoke condensation, add water each
time after it dries up.
COOKING TIMES
Cooking times depend on the type of food, its
consistency, and volume.
Casseroles
Food
Lasagna
Quantity (kg) Knob position
Preheating
time (min)
Time (min)
Shelf position
1.5 - 2.5
1/2
10
45 - 55
2
Cannelloni
1.5 - 2.5
1/2
10
35 - 45
2
Potato gratin
1.5 - 2.5
1/2
10
80 - 90
2
Macaroni oven
1.5 - 2.5
1/2
10
40 - 50
2
Kebab Hala
1.5 - 2.5
1/2
10
40 - 50
2
Meat
Food
12
Quantity (kg) Knob position
Preheating
time (min)
Time (min)
Shelf position
Sheep
1.5 - 2.0
2
10
80 - 1001)
2
Chicken
1.2 - 1.8
2
10
90 - 1101)
2
Duck
1.8 - 2.5
2
10
80 - 1001)
2
Goose
2.5 - 3.0
2
10
90 - 1001)
2
Food
Quantity (kg) Knob position
Preheating
time (min)
Time (min)
Shelf position
Rabbit
1.0 - 1.5
2
10
80 - 1001)
2
Beef
1.2 - 1.8
2
10
90 - 1001)
2
1) Turn over after half of cooking time.
Fish
Food
Quantity (kg) Knob position
Preheating
time (min)
Time (min)
Shelf position
Pike
0.8 - 1.5
1/2
10
50 - 60
2
Dorade
0.4 - 0.7
1/2
10
35 - 40
2
Trout
0.5 - 1.0
1/2
10
35 - 45
2
Pizza
Food
Quantity (kg) Knob position
Preheating
time (min)
Time (min)
Shelf position
Thin
1.0 - 1.2
1/2
10
25 - 30
1
Thick
1.4 - 1.5
1/2
10
25 - 30
1
Calzone
1.4 - 1.5
1/2
10
30 - 35
1
Cakes
Food
Quantity (kg)
Knob position
Preheating
time (min)
Time (min)
Shelf position
Biscuits
0.3 - 0.5
1
10
10 - 20
3
Flat cake
0.6 - 1.0
1/2
10
25 - 30
2
Orange cake
1.0 - 1.5
1
10
110 - 115
2
Feter Mshalted
1.0 - 1.5
1/2
10
50 - 60
1
Salty cake
1.0 - 1.2
1/2
10
45 - 55
2
Yeast cake
1.0 - 1.5
1/2
10
40 - 50
2
Apple pie
1.0 - 1.5
1/2
10
70 - 90
2
13
Grilling
Food
Quantity (kg)
Grill position
Preheating
time (min)
Time (min)
Shelf position
Sheep chops
0.7 - 1.2
on
10
20 - 25
3
Ribs
1.0 - 1.2
on
10
40 - 50
3
Burgers
2.0 - 2.5
on
10
40 - 50
3
Mackerel
1.2 - 1.5
on
10
25 - 35
3
Toast browning
0.3 - 0.5
on
10
4-8
3
Toast Hawai
0.5 - 1.0
on
10
15 - 20
3
OVEN - CARE AND CLEANING
WARNING! Refer to Safety chapters.
NOTES ON CLEANING
Clean the front of the oven with a soft cloth with
warm water and a mild cleaning agent.
To clean metal surfaces, use a dedicated cleaning
agent.
Clean the oven interior after each use. Fat
accumulation or other food remains may result in a
fire.
Clean all accessories after each use and let them
dry. Use a soft cloth with warm water and a
cleaning agent.
Clean stubborn dirt with a special oven cleaner.
If you have nonstick accessories, do not clean them
using aggressive agents, sharp-edged objects or a
dishwasher. It can cause damage to the nonstick
coating.
Clean the moisture from the cavity after each use.
STAINLESS STEEL OR ALUMINIUM OVENS
Clean the oven door with a damp cloth or sponge
only. Dry it with a soft cloth.
Do not use steel wool, acids or abrasive materials
as they can damage the oven surface. Clean the
oven control panel with the same precautions.
CLEANING THE OVEN DOOR
The oven door has two panels of glass installed
one behind the other. To make the cleaning easier
remove the oven door.
14
WARNING! The oven door can close
if you try to remove the internal panel
of glass when the door is still
assembled.
Do not lose the screws.
1. Open the door fully and hold the two door
hinges.
2. Lift and turn the levers on the two hinges.
outer door, and push the inner door against the
top edge of the door. Lift the inner door.
3
2
2
3. Close the oven door to the first opening
position (halfway). Then pull forward and
remove the door from its seat.
7. Clean the oven door with water and soap.
Clean inner side of the door. Dry the oven door
carefully.
When the cleaning is completed, install the glass
panels and the oven door. To install the oven door,
do the above steps in the opposite sequence.
4
4
6
5
5
4. Put the door on a soft cloth on a stable surface.
5. Use a screwdriver to remove 2 screws from
bottom edge of door.
REPLACING THE LAMP
WARNING! Risk of electric shock.
The lamp can be hot.
1
1
6. Use a spatula made of wood or plastic or
equivalent to open the inner door. Hold the
1. Turn off the oven.
Wait until the oven is cooled down.
2. Disconnect the oven from the mains.
3. Put a cloth on the bottom of the cavity.
The back lamp
1. Turn the lamp glass cover to remove it.
2. Clean the glass cover.
3. Replace the lamp with a suitable 300 °C heatresistant lamp.
4. Install the glass cover.
15
TROUBLESHOOTING
WARNING! Refer to Safety chapters.
WHAT TO DO IF...
Problem
16
Possible cause
Remedy
There is no spark when you try
to activate the spark generator.
The hob is not connected to an
electrical supply or it is connected incorrectly.
Check if the hob is correctly
connected to the electrical
supply. Refer to the connection
diagram.
There is no spark when you try
to activate the spark generator.
The fuse is blown.
Make sure that the fuse is the
cause of the malfunction. If the
fuse is blown again and again,
contact a qualified electrician.
There is no spark when you try
to activate the spark generator.
Burner cap and crown are
placed incorrectly.
Place the burner cap and
crown correctly.
The flame extinguishes immediately after ignition.
Thermocouple is not heated up
sufficiently.
After lightning the flame, keep
the spark generator activated
for equal or less than 10 seconds
The flame ring is uneven.
Burner crown is blocked with
food residues.
Make sure that the injector is
not blocked and the burner
crown is clean.
The burners do not work.
There is no gas supply.
Check the gas connection.
The appliance makes noises.
Some metal parts of the appliance expand and contract
when they heat up or cool
down. The noises are normal.
The flame colour is orange or
yellow.
The flame can look orange or
yellow in some areas of the
burner. This is normal.
The lamp does not operate.
The lamp is defective.
Replace the lamp.
Steam and condensation settle
on the food and in the cavity of
the oven.
You left the dish in the oven for
too long.
Do not leave the dishes in the
oven for longer than 15 - 20
minutes after the cooking
process ends.
The oven does not heat up.
The necessary settings are not
set.
Make sure that the settings are
correct.
It takes too long to cook the
dishes or they cook too quickly.
The temperature is too low or
too high.
Adjust the temperature if necessary. Follow the advice in the
user manual.
SERVICE DATA
If you cannot find a solution to the problem yourself,
contact your dealer or an Authorised Service
Centre.
The necessary data for the service centre is on the
rating plate. The rating plate is on the front frame of
the oven cavity. Do not remove the rating plate from
the oven cavity.
We recommend that you write the data here:
Model (MOD.)
.........................................
Product number (PNC)
.........................................
Serial number (S.N.)
.........................................
INSTALLATION
WARNING! Refer to Safety chapters.
LOCATION OF THE APPLIANCE
You can install your freestanding appliance with
cabinets on one or two sides and in the corner.
Keep a distance of about 1 cm
between the appliance and the back
wall to make sure that the lid opens.
For minimal distances for fitting check the table.
Dimension
mm
B
650
C
150
D
20
TECHNICAL DATA
Voltage
220 - 240 V
Frequency
50 - 60 Hz
Appliance class
1
Dimension
B
C
mm
A
D
D
Height
850 - 870
Width
600
Depth
600
Minimum distances
Dimension
A
mm
400
17
OTHER TECHNICAL DATA
Appliance category:
II2H3B/P
LPG:
G30 (3B/P) 28-30 mbar
Natural Gas:
G20 (2H) 20 mbar
BYPASS DIAMETERS
BURNER
Ø BYPASS 1/100 mm
Auxiliary
29 / 30
Semi-rapid
32
Rapid
42
Oven
50
Grill
50
GAS BURNERS FOR NATURAL GAS G20 20 mbar
BURNER
NORMAL POWER kW
REDUCED POWER kW
INJECTOR MARK
1/100 mm
Rapid
3.0
0.75
119
Semi-rapid
2.0
0.45
96
Auxiliary
1.0
0.35
70
Oven
2.5
1.0
104
Grill
2.4
1.5
104
GAS BURNERS FOR LPG G30 28-30 mbar
BURNER
NORMAL POWER kW
GAS RATE g/h
INJECTOR MARK
1/100 mm
Rapid
3.0
218.1
0.72
88
Semi-rapid
2.0
145.4
0.43
71
Auxiliary
1.0
72.7
0.35
50
Oven
2.5
181.8
1.0
75
Grill
2.4
174.5
1.5
75
GAS CONNECTION
The gas pipe in the appliance has two endings. You
can connect the gas supply to either one of them.
The pipe that is not used must be clogged with the
pipe closer, which added to the appliance.
18
REDUCED POWER
kW
Use a fixed connections or use a flexible stainless
steel pipes in compliance with the regulation in
force. If you use flexible metallic pipes, make sure
they do not come in touch with mobile parts and
they are not squeezed.
ADJUSTMENT TO DIFFERENT TYPES OF GAS
WARNING! Let only an authorized
person do the adjustment to different
types of gas.
If the appliance is set for liquid gas
you can change it to natural gas, with
the correct injectors.
The gas rate is adjusted to suit.
FLEXIBLE NONMETAL PIPES CONNECTION
If you have an easy access to the connection, you
can use a flexible pipe. The flexible pipe must be
tightly attached by clamps.
In installation always use the pipe holder and the
gasket. The flexible pipe can be applied when:
• it can not get hotter than room temperature,
higher than 30 °C,
• it is not longer than 1500 mm,
• it has no narrowing anywhere,
• it is not twisted or tighten,
• it does not get in touch with sharp edges or
corners,
• it's conditions can be easily checked.
When checking the flexible pipe make sure:
• it does not show cracks, cuts, marks of burnings
on the two ends and on its full length,
• the material is not hardened, but shows its
correct elasticity,
• the fastening clamps are not rusted,
• expired term is not due.
If one or more defects are visible, do not repair the
pipe, but replace it.
WARNING! When installation is
complete, make sure that the seal of
each pipe fitting does not leak. To
check the seal use a soap solution, not
a flame.
The gas supply ramp is on the rear side of the
control panel.
WARNING! Before you replace the
injectors, make sure that the gas
knobs are in the Off position.
Disconnect the appliance from the
electrical supply. Let the appliance
cool down. There is a risk of injury.
The appliance is set to default gas. To
change the setting choose a pipe
holder from the list. Always use the
gasket sealing.
A
B
A. Gas connection end
B. LPG pipe holder
HOB INJECTORS REPLACEMENT
Replace the injectors when you change the gas
type.
1. Remove the pan supports.
2. Remove the caps and crowns of the burner.
3. Remove the injectors with a socket spanner 7.
4. Replace injectors with the ones necessary for
the type of gas you use.
WARNING! Before you connect the
gas, disconnect the appliance from the
electricity supply or switch off the fuse
in the fuse box. Close the primary
valve of the gas supply.
19
4.
5.
6.
7.
8.
WARNING! Put the mains plug
into the mains socket only if all
parts are back into their initial
position. There is a risk of injury.
Light the burner.
Refer to "Hob - Daily use" chapter.
Turn the knob for the hob to the minimum
position.
Remove the knob for the hob again.
Screw on slowly the bypass screw till the flame
becomes minimum and stable.
Put the knob for the hob back on.
OVEN INJECTOR REPLACEMENT
5. Replace the rating plate (it is near the gas
supply pipe) with the one for the new type of
gas supply.
1. Remove the bottom plate of the oven cavity to
get access to the oven burner .
You can find this plate in the bag
supplied with the appliance.
If the supply gas pressure is not constant or it is
different from the necessary pressure, install an
applicable pressure adjuster on the gas supply
pipe.
ADJUSTING THE MINIMUM GAS LEVEL ON
THE HOB BURNER
1. Disconnect the appliance from the electricity.
2. Remove the knob for the hob. If there is no
access to the bypass screw dismount the
control panel before adjustment start.
3. With a thin and flat screwdriver adjust the
bypass screw A.
The model determines the position of the
bypass screw A.
2. Carefully remove from the burner the
thermocouple A. Next remove the spark plug B.
A
B
A
A
Changing from natural gas to liquid gas
1. Fully tighten the bypass screw.
2. Put the knob back.
Changing from liquid gas to natural gas
1. Unscrew approximately one turn the bypass
screw position A.
2. Put the knob for the hob back.
3. Connect the appliance to the electricity.
20
3. Unscrew the screw and slowly pull out the
burner.
Changing from liquid gas to natural gas
1. Unscrew approximately one turn the bypass
screw position A.
2. Put the knob for the oven functions back.
3. Connect the appliance to the electricity.
1
2
4. Release the burner injector with a 7 mm socket
spanner and replace it with a right one.
Assemble the burner in a revers sequence.
Replace the gas type sticker near the gas supply
ramp with the one related to the new gas type.
ADJUSTING THE MINIMUM GAS LEVEL ON
THE OVEN BURNER
1. Disconnect the appliance from the electricity.
2. Remove the knob for the oven functions. If
there is no access to the bypass screw
dismount the control panel before adjustment
start.
3. With a thin and flat screwdriver adjust the
bypass screw A.
The model determines the position of the
bypass screw A.
A
WARNING! Put the mains plug
into the mains socket only if all
parts are back into their initial
position. There is a risk of injury.
4. Light the burner.
Refer to "Oven - Daily use" chapter.
5. Turn the knob for the oven functions on the
minimum position.
6. Remove the knob for the oven functions again.
7. Screw on slowly the bypass screw till the flame
becomes minimum and stable.
8. Put the knob for the oven functions back.
9. Set the maximum gas flow position on the knob
for the oven functions and let the oven heat for
at least 10 minutes.
10. Quickly turn the knob for the oven functions
from maximum to the minimum gas flow
position.
Control the flame. Make sure the flame does not go
out when you turn the knob to the minimum gas
flow position. There must be a small regular flame
on the oven burner crown. If the flame goes out
adjust the oven burner again.
GAS GRILL INJECTOR REPLACEMENT
1. Release the screws which keep the grill burner
in position A.
A
2. Release the burner injector with a 7 mm socket
spanner and replace it with a right one.
A
Changing from natural gas to liquid gas
1. Fully tighten the bypass screw.
2. Put the knob back.
3. Connect the appliance to the electricity.
21
B
3. Assemble the burner in a reverse sequence.
Before you fix the screw, make sure that the
burner is pushed correctly to the back panel.
Test the grill injectors.
LEVELLING
4. If the floor is not equally flat, use the adjustable
feet on the bottom of the appliance to set a
stable position for the appliance.
CAUTION! Remove all the
accessories from the oven.
1. Open the lid of the appliance and disassemble
it.
2. Disassemble the pan supports and all the
burner assemblies.
To install all the accessories, do the first step in an
opposite sequence.
ELECTRICAL INSTALLATION
WARNING! The manufacturer is not
responsible if you do not follow the
safety precautions from Safety
chapters.
This appliance is supplied with a main plug and a
main cable.
3. Put the appliance on the sidewall on a clean
and smooth surface. Place each foot into a
separate hole, in the plinth, and rotate it
clockwise.
22
WARNING! The power cable must
not touch the part of the appliance
shaded in the illustration.
ENVIRONMENTAL CONCERNS
with the symbol with the household waste.
Return the product to your local recycling facility or
contact your municipal office.
Recycle materials with the symbol
. Put the
packaging in relevant containers to recycle it. Help
protect the environment and human health by
recycling waste of electrical and electronic
appliances. Do not dispose of appliances marked
23
*
867342012-E-462018
WWW.ZANUSSI.COM/SHOP
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising