IKEA | HÖGKLASSIG | User manual | IKEA HÖGKLASSIG User Manual

IKEA HÖGKLASSIG User Manual
GB
HÖGKLASSIG
ENGLISH
Please refer to the last page of this manual for the full list of IKEA
appointed After Sales Service Provider and relative national phone
numbers.
ENGLISH
4
4
ENGLISH
Contents
Safety information
Safety instructions
Installation
Electrical connection
Product description
Daily use
Flexible induction cooking area
4
6
8
9
10
12
14
Hints and tips
Care and cleaning
Troubleshooting
Technical data
Energy efficiency
Environmental concerns
IKEA guarantee
19
19
20
23
23
24
24
Subject to change without notice.
Safety information
Before the installation and use of the appliance, carefully read
the supplied instructions. The manufacturer is not responsible if
an incorrect installation and use causes injuries and damages.
Always keep the instructions with the appliance for future
reference.
Children and vulnerable people safety
•
•
•
•
•
This appliance can be used by children aged from 8 years
and above and persons with reduced physical, sensory or
mental capabilities or lack of experience and knowledge if
they have been given supervision or instruction concerning
the use of the appliance in a safe way and understand the
hazards involved.
Children between 3 and 8 years of age and persons with
very extensive and complex disabilities shall be kept away
from the appliance unless continuously supervised.
Children of less than 3 years of age should be kept away
from the appliance unless continuously supervised.
Do not let children play with the appliance.
Keep all packaging away from children and dispose of it
appropriately.
ENGLISH
•
•
•
5
Keep children and pets away from the appliance when it
operates or when it cools down. Accessible parts may
become hot during use.
If the appliance has a child safety device, it should be
activated.
Children shall not carry out cleaning and user maintenance of
the appliance without supervision.
General Safety
•
•
•
•
•
•
•
•
•
•
•
WARNING: The appliance and its accessible parts become
hot during use. Care should be taken to avoid touching
heating elements.
Do not operate the appliance by means of an external timer
or separate remote-control system.
WARNING: Unattended cooking on a hob with fat or oil can
be dangerous and may result in fire.
NEVER try to extinguish a fire with water, but switch off the
appliance and then cover flame e.g. with a lid or a fire
blanket.
CAUTION: The cooking process has to be supervised. A short
term cooking process has to be supervised continuously.
WARNING: Danger of fire: Do not store items on the cooking
surfaces.
Metallic objects such as knives, forks, spoons and lids should
not be placed on the hob surface since they can get hot.
Do not use the appliance before installing it in the built-in
structure.
Do not use a steam cleaner to clean the appliance.
After use, switch off the hob element by its control and do not
rely on the pan detector.
If the glass ceramic surface / glass surface is cracked, switch
off the appliance and unplug it from the mains. In case the
appliance is connected to the mains directly using junction
6
ENGLISH
•
•
box, remove the fuse to disconnect the appliance from power
supply. In either case contact the Authorised Service Centre.
If the supply cord is damaged, it must be replaced by the
manufacturer, the Authorised Service Centre or similarly
qualified persons in order to avoid a hazard.
WARNING: Use only hob guards designed by the
manufacturer of the cooking appliance or indicated by the
manufacturer of the appliance in the instructions for use as
suitable or hob guards incorporated in the appliance. The
use of inappropriate guards can cause accidents.
Safety instructions
Installation
Warning! The appliance must be
installed by the authorised
installer.
• Remove all the packaging.
• Do not install or use a damaged
appliance.
• Follow the installation instructions
supplied with the appliance.
• Keep the minimum distance from other
appliances and units.
• Always take care when moving the
appliance as it is heavy. Always use
safety gloves and enclosed footwear.
• Seal the cut surfaces with a sealant to
prevent moisture to cause swelling.
• Protect the bottom of the appliance from
steam and moisture.
• Do not install the appliance adjacent to
a door or under a window. This prevents
hot cookware falling from the appliance
when the door or the window is opened.
• If the appliance is installed above
drawers make sure that the space,
between the bottom of the appliance
and the upper drawer, is sufficient for air
circulation.
• The bottom of the appliance can get hot.
Make sure to install a non-combustible
separation panel under the appliance to
prevent access to the bottom.
Refer to the Assembly Instructions.
• Make sure that the ventilation space of 2
mm, between the worktop and the front
of the below unit, is free. The warranty
does not cover damages caused by the
lack of an adequate ventilation space.
Electrical Connection
Warning! Risk of fire and electric
shock.
• All electrical connections should be made
by the authorised installer.
• The appliance must be earthed.
• Before carrying out any operation make
sure that the appliance is disconnected
from the power supply.
• Make sure that the parameters on the
rating plate are compatible with the
electrical ratings of the mains power
supply.
• Make sure the appliance is installed
correctly. Loose and incorrect electricity
mains cable or plug (if applicable) can
make the terminal become too hot.
• Use the correct electricity mains cable.
• Do not let the electricity mains cable
tangle.
ENGLISH
• Make sure that a shock protection is
installed.
• Use the strain relief clamp on the cable.
• Make sure the mains cable or plug (if
applicable) does not touch the hot
appliance or hot cookware, when you
connect the appliance to the near
sockets.
• Do not use multi-plug adapters and
extension cables.
• Make sure not to cause damage to the
mains plug (if applicable) or to the mains
cable. Contact our Authorised Service
Centre or an electrician to change a
damaged mains cable.
• The shock protection of live and
insulated parts must be fastened in such
a way that it cannot be removed without
tools.
• Connect the mains plug to the mains
socket only at the end of the installation.
Make sure that there is access to the
mains plug after the installation.
• If the mains socket is loose, do not
connect the mains plug.
• Do not pull the mains cable to disconnect
the appliance. Always pull the mains
plug.
• Use only correct isolation devices: line
protecting cut-outs, fuses (screw type
fuses removed from the holder), earth
leakage trips and contactors.
• The electrical installation must have an
isolation device which lets you disconnect
the appliance from the mains at all poles.
The isolation device must have a contact
opening width of minimum 3 mm.
Use
Warning! Risk of injury, burns
and electric shock.
• Remove all the packaging, labelling and
protective film (if applicable) before first
use.
• This appliance is for household use only.
• Do not change the specification of this
appliance.
7
• Make sure that the ventilation openings
are not blocked.
• Do not let the appliance stay unattended
during operation.
• Set the cooking zone to “off” after each
use.
• Do not rely on the pan detector.
• Do not put cutlery or saucepan lids on
the cooking zones. They can become hot.
• Do not operate the appliance with wet
hands or when it has contact with water.
• Do not use the appliance as a work
surface or as a storage surface.
• If the surface of the appliance is cracked,
disconnect immediately the appliance
from the power supply. This to prevent
an electrical shock.
• Users with a pacemaker must keep a
distance of minimum 30 cm from the
induction cooking zones when the
appliance is in operation.
• When you place food into hot oil, it may
splash.
Warning! Risk of fire and
explosion
• Fats and oil when heated can release
flammable vapours. Keep flames or
heated objects away from fats and oils
when you cook with them.
• The vapours that very hot oil releases
can cause spontaneous combustion.
• Used oil, that can contain food remnants,
can cause fire at a lower temperature
than oil used for the first time.
• Do not put flammable products or items
that are wet with flammable products in,
near or on the appliance.
Warning! Risk of damage to the
appliance.
• Do not keep hot cookware on the control
panel.
• Do not put a hot pan cover on the glass
surface of the hob.
• Do not let cookware boil dry.
ENGLISH
8
• Be careful not to let objects or cookware
fall on the appliance. The surface can be
damaged.
• Do not activate the cooking zones with
empty cookware or without cookware.
• Do not put aluminium foil on the
appliance.
• Cookware made of cast iron, aluminium
or with a damaged bottom can cause
scratches on the glass / glass ceramic.
Always lift these objects up when you
have to move them on the cooking
surface.
• This appliance is for cooking purposes
only. It must not be used for other
purposes, for example room heating.
• Do not use water spray and steam to
clean the appliance.
• Clean the appliance with a moist soft
cloth. Only use neutral detergents. Do
not use any abrasive products, abrasive
cleaning pads, solvents or metal objects.
Care and cleaning
• Contact your municipal authority for
information on how to discard the
appliance correctly.
• Disconnect the appliance from the mains
supply.
• Cut off the mains electrical cable close to
the appliance and dispose of it.
• Clean the appliance regularly to prevent
the deterioration of the surface material.
• Deactivate the appliance and let it cool
down before you clean it.
• Disconnect the appliance from the
electrical supply before maintenance.
Installation
General information
Installation process must follow
the laws, ordinances, directives
and standards (electrical safety
rules and regulations, proper
recycling in accordance with the
regulations, etc.) in force in the
country of use!
Service
• To repair the appliance contact the
Authorised Service Centre.
• Use original spare parts only.
Disposal
Warning! Risk of injury or
suffocation.
ENGLISH
9
780 mm
490±1
mm
min.
500 mm
520 mm
750±1
mm
min. 100 mm
min.
38 mm
min. 5 mm
55 mm max.
R 5 mm
5 mm
min.
38 mm
Important!
• For further information on the installation
refer to the Assembly Instruction.
• If there is no oven beneath the hob insert
a dividing panel at a minimum distance
of 20 mm from the bottom of the hob.
• Do not use silicon sealant between the
appliance and the worktop.
Electrical connection
Warning! Refer to Safety
chapters.
Warning! All electrical
connections must be made by an
authorised installer.
Electrical connection
• Before connecting, check that the
nominal voltage of the appliance, stated
on the rating plate, corresponds to the
available supply voltage. Also, check the
power rating of the appliance and
ensure that the wire is suitably sized to
suit the appliance power rating (refer to
the "Technical data" chapter). The rating
plate is located on the lower casing of
the hob.
• The appliance is not provided with a
mains cable. Buy the right one from a
specialised dealer. Single phase or twophase connection requires a mains cable
of minimum 70°C temperature stability.
Cable needs mandatory end sleeves.
According to IEC regulations use for onephase connection: mains cable 3 x 4mm²
and for two-phase connection: mains
cable 4 x 2.5mm². Please respect in first
priority specific national regulations.
• The appliance works perfectly on AC
230 V, AC 220 V~ or AC 240 V~ 50 Hz
electrical network.
• You must have the means for
disconnection incorporated in the fixed
wiring. Have the appliance connected to
the mains using a device that allows the
appliance to be disconnected from the
mains at all poles with a contact opening
ENGLISH
10
width of at least 3 mm, eg. automatic line
protecting cut-out, earth leakage trips or
fuse.
• You must have the connection and the
connecting links carried out as shown in
the connection diagram (it is located on
the underneath surface of the casing of
the hob). The earth lead is connected to
terminal marked with the symbol and
must be longer than leads carrying
electric current. Tighten the terminal
screws securely! Finally, secure the
connecting cable with the mains cable
cleat and the covering closed by
pressing firmly (lock into place).
Warning! Once connected to the
mains supply check that all
cooking zones are ready for use
by briefly setting each to
maximum power.
Product description
Cooking surface layout
1 Single cooking zone (210mm) 2300W,
with Booster 3200W
Single
cooking zone (180mm) 1800W,
2
with Booster 2800W
3 Control panel
4 Flexible induction cooking area (240 x
440mm) 2400W, with Booster 3300W
1
2
4
3
Control panel layout
1
2
3 4
5
6
13
7
12
8
11
10
9
Press the symbol to operate the appliance. The display, indicators and sounds tell which
function operate.
ENGLISH
11
Symbol
Function
Comment
1
ON / OFF
2
Lock / Child Safety Device To lock / unlock the control panel.
3
Pre-Set Cooking mode
To activate and deactivate the function.
Multi-Flexi mode
To switch between three modes of the function.
-
Power setting display
To show the power setting.
-
Timer indicators of cooking zones
To show for which zone you set the time.
-
Timer display
To show the time in minutes.
8
STOP+GO
To activate and deactivate the function.
9
Booster function
To activate and deactivate the function.
Power selector
To set the power setting.
-
To select the cooking zone for the timer.
-
To increase or decrease the time.
Power selector
To set the power setting for flexible induction
cooking area.
4
5
6
7
10
-
11
/
12
13
-
To activate and deactivate the hob.
Power setting displays
Display
Description
The cooking zone is deactivated.
-
The cooking zone operates.
STOP+GO function operates.
Booster function operates.
+ digit
There is a malfunction. Refer to "Troubleshooting" chapter.
Lock / Child Safety Device function operates.
ENGLISH
12
Display
Description
Incorrect or too small cookware or no cookware on the cooking zone.
Automatic Switch Off function operates.
/
/
Pre-Set Cooking mode operates.
Warning! There is a risk of burns
from residual heat.
directly in the bottom of the cookware. The
glass ceramic is heated by the heat of the
cookware.
The induction cooking zones produce the
heat necessary for the cooking process
Daily use
Warning! Refer to Safety
chapters.
Activating and deactivating
Touch
for 1 second to activate or
deactivate the appliance.
Power setting
,
• all cooking zones are deactivated.
• you do not set the power setting after
activating the hob.
• you cover any symbol with an object (a
pan, a cloth, etc.) for longer than approx.
10 seconds.
• you do not deactivate a cooking zone
after a certain time, or you do not modify
the power setting, or if the overheating
occurs (e.g. when a pan boils dry). The
symbol
lights up. Before using again,
you must set the cooking zone to .
6 hours
-
5 hours
-
4 hours
Automatic Switch Off
The function deactivates the hob
automatically if:
Automatic switch off
after
-
1.5 hours
If cookware that is not suitable is
used,
lights up on the display
and after 2 minutes the indicator
for the cooking zone deactivates
itself.
Adjusting the power setting
Touch the power selector at a desired
power setting. Correct to the left or the
right, if necessary. Do not release before
you reach a desired power setting.
13
ENGLISH
Using the Booster function
The Booster function makes additional
power available for the induction cooking
zones. Touch
to activate it, a
lights up
on the display. After maximum 10 minutes,
the induction cooking zones automatically
return to cooking level
.
Using the Timer
Touch
repeatedly until the indicator of a
desired cooking zone flashes. For example
for the front right zone.
STOP+GO
The function sets all cooking zones that
operate to the lowest power setting .
When the function operates, you cannot
change the power setting. The function does
not stop the timer function.
• To activate this function touch . The
symbol
comes on.
• To deactivate this function touch . The
power setting that you set before comes
on.
Lock
When the cooking zones operate, you can
lock the control panel, but not deactivate
the appliance. It prevents an accidental
change of the power setting.
First set the power setting.
To start this function touch
Touch
or
of the Timer to set the time
between 00 and 99 minutes. When the
indicator of the cooking zone flashes more
slowly, the time counts down. Set the power
setting.
If the power setting is set and the time set
has elapsed, an acoustic signal sounds, 00
flashes, and cooking zone deactivates. If
cooking zone is not in use and the time set
has elapsed an acoustic signal sounds and
00 flashes.
to deactivate the function for the
Touch
selected cooking zone and the indicator for
this cooking zone flashes faster. Touch
and the remaining time counts backwards
to 00. The indicator of the cooking zone
goes out.
on.
. The symbol
comes on for 4 seconds. The Timer stays
To stop this function touch . The power
setting that you set before comes on.
When you stop the appliance, you also stop
this function.
The Child Safety Device
This function prevents an accidental
operation of the appliance.
To activate the Child Safety Device
• Activate the appliance with . Do not
set the power settings.
• Touch
for 4 seconds. The symbol
comes on.
• Deactivate the appliance with .
To deactivate the Child Safety Device
ENGLISH
14
• Activate the appliance with . Do not
set the power settings. Touch
for 4
comes on.
seconds. The symbol
• Deactivate the appliance with .
To override the Child Safety Device for
only one cooking time
• Activate the appliance with . The
symbol
comes on.
for 4 seconds. Set the power
• Touch
setting in 10 seconds. You can operate
the appliance.
• When you deactivate the appliance with
, the Child Safety Device operates
again.
OffSound Control - Deactivating and
activating the sounds
Deactivating the sounds
Deactivate the appliance.
Touch
comes on, because the sound is off. Touch
,
comes on. The sound is on.
Power exchange function
• Cooking zones are grouped according to
the location and number of the phases in
the hob. See the illustration.
• Each phase has a maximum electricity
loading of 3700 W.
• The function divides the power between
cooking zones connected to the same
phase.
• The function activates when the total
electricity loading of the cooking zones
connected to a single phase exceeds
3700 W.
• The function decreases the power to the
other cooking zones connected to the
same phase.
• The power setting display of the reduced
zones changes between two levels.
for 3 seconds. The displays comes
on and goes out. Touch
for 3 seconds.
comes on, the sound is on. Touch
comes on, the sound is off.
,
When this function operates, you can hear
the sounds only when:
• you touch
• you put something on the control panel.
Activating the sounds
Deactivate the appliance.
Touch
for 3 seconds. The displays come
on and go out. Touch
for 3 seconds.
Flexible induction cooking area
Warning! Refer to Safety
chapters.
Multi-Flexi mode
The flexible induction cooking area consists
of four sections. The sections can be
combined into two cooking zones with
15
ENGLISH
different size, or into one large cooking
area. You choose the combination of the
sections by choosing the mode applicable
to the size of the cookware you want to use.
There are three modes: Multi-Flexi mode 2
+ 2 sections (activated automatically when
you activate the hob), Multi-Flexi mode 3 +
1 sections and Multi-Flexi mode 4 sections.
To set the power setting use two
left side power selectors.
Switching between the modes
To switch between the modes use symbol:
100-160mm
.
Place the cookware with the bottom
diameter larger then 160 mm centrally
between two sections.
When you switch between the
modes the power setting is set
back to 0.
Diameter and position of the cookware
Choose the mode applicable to the size
and the shape of the cookware. The
cookware should cover the selected area as
much as possible. Place the cookware
centrally on the selected area!
Place the cookware with the bottom
diameter smaller than 160 mm centrally on
a single section.
> 160 mm
Multi-Flexi mode 2 + 2 sections
This mode is active when you activate the
hob. It connects the sections into two
separate cooking zones. You can set the
power setting for each zone separately. Use
two left side power selectors.
16
ENGLISH
Correct cookware position:
Correct cookware position:
To use this mode you have to place the
cookware on the three connected sections.
If you use cookware smaller than two
and after 2
sections the display shows
minutes the zone deactivates.
Incorrect cookware position:
Incorrect cookware position:
Multi-Flexi mode 3 + 1 sections
To activate the mode press
until you see
the correct mode indicator. This mode
connects three rear sections into one
cooking zone. The one front section is not
connected and operates as a separate
cooking zone. You can set the power setting
for each zone separately. Use two left side
power selectors.
Multi-Flexi mode 4 sections
To activate the mode press
until you see
the correct mode indicator. This mode
connects all sections into one cooking zone.
ENGLISH
17
To set the power setting use one of the left
side power selector.
Correct cookware position:
To use this mode you have to place the
cookware on the four connected sections. If
you use cookware smaller than three
and after 2
sections the display shows
minutes the zone deactivates.
Pre-Set Cooking mode
This function allows you to adjust the
temperature by moving the cookware to a
different position on the induction cooking
area.
The function divides the induction cooking
area into three areas with different power
settings. The hob senses the position of the
cookware and sets the power setting
corresponding with the position. You can
place the cookware in the front, middle or
rear position. If you place the cookware in
the front you get the highest power setting.
You can decrease the power setting by
moving the cookware in the middle or to the
rear position.
Use only one pot when you
operate the function.
Incorrect cookware position:
ENGLISH
General information:
• 160 mm is the minimum bottom diameter
of the cookware for this function.
• Power setting display for the left rear
power selector shows the position of the
cookware on the induction cooking area.
Front
, middle
, rear
.
18
You can change the power settings for
each position separately. The hob will
remember your power settings next time
you activate the function.
Activating the function
To activate the function place the cookware
in the correct position on the cooking area.
Touch . The indicator above the symbol
comes on. If you do not place the cookware
on the cooking area
comes on and after
2 minutes the flexible induction cooking
area is set to
.
Deactivating the function
• Power setting display for the left front
power selector shows the power setting.
To change the power setting use left
front power selector.
• When you activate the function for the
first time you will get power setting
for the front position,
for the middle
for the rear position.
position and
To deactivate the function touch
the power setting to
above the symbol
or set
. The indicator
goes off.
ENGLISH
19
Hints and tips
Noises during operation
When a cooking zone is active, it
may hum briefly. This is a
characteristic of all ceramic glass
cooking zones and does not
impair either the function or the
life of the appliance.
Cookware for induction cooking zones
Use the induction cooking zones
with correct cookware.
Cookware material
• correct: cast iron, steel, enamelled steel,
stainless steel, the bottom made of multilayer (with correct mark from a
manufacturer).
• not correct: aluminium, copper, brass,
glass, ceramic, porcelain.
Cookware is correct for an induction hob
if …
• ... some water boils very quickly on a
zone set to the highest power setting...
• ... a magnet pulls on to the bottom of the
cookware.
The bottom of the cookware must
be as thick and flat as possible.
Cookware sizes
Induction cooking zones adapt
automatically to the size of the bottom of
the cookware. But, it must have a minimum
diameter depending on the size of the
cooking zone.
Cooking zone
Cookware diameter [mm]
Middle rear cooking
zone
125 - 210
Right front cooking
zone
145 - 180
Flexible induction
cooking area
minimum 100
Care and cleaning
General information
Warning! Deactivate the
appliance and let it cool down
before you clean it.
Warning! For safety reasons, do
not clean the appliance with
steam blasters or high-pressure
cleaners.
Warning! Sharp objects and
abrasive cleaning agents will
damage the appliance. Clean
the appliance and remove the
residues with water and washing
up liquid after each use. Remove
also the remnants of the cleaning
agents!
Scratches or dark stains on the
glass ceramic that cannot be
removed do not affect the
functioning of the appliance.
ENGLISH
20
Removing the residues and stubborn
residues
1. Food containing sugar, plastics, tin foil
residues should be removed at once,
best tool for cleaning glass surface is a
scraper (not included with the
appliance). Place a scraper on the glass
ceramic surface at an angle and remove
residues by sliding the blade over the
surface. Wipe the appliance with a
damp cloth and a little washing up
liquid. Finally, rub the appliance dry
using a clean cloth.
2. Limescale rings, water rings, fat
splashes, shiny metallic discolorations
should be removed after the appliance
has cooled down using cleaner for glass
ceramic or stainless steel.
Troubleshooting
Warning! Refer to Safety
chapters.
What to do if...
Problem
Possible cause
You cannot activate or oper- The hob is not connected to
ate the hob.
an electrical supply or it is
connected incorrectly.
The fuse is blown.
Remedy
Check if the hob is correctly
connected to the electrical
supply. Refer to the connection diagram.
Make sure that the fuse is
the cause of the malfunction.
If the fuse is blown again
and again, contact a qualified electrician.
Activate the hob again and
set the power setting is less
than 10 seconds.
You touched 2 or more sym- Touch only one symbol.
bols at the same time.
STOP+GO function operates. Refer to "Daily use" chapter.
There is water or fat stains
on the control panel.
Clean the control panel.
An acoustic signal sounds
You put something on one or Remove the object from the
and the hob deactivates.
more symbols.
symbols.
An acoustic signal sounds
when the hob is deactivated.
ENGLISH
Problem
The hob deactivates.
21
Possible cause
You put something on the
symbol
Remedy
Remove the object from the
symbols.
The power setting changes
between two levels.
Power exchange function
operates.
Refer to "Daily use" chapter.
The symbols become hot.
The cookware is too large or Put large cookware on the
you put it too near to the
rear zones if possible.
controls.
There is no signal when you
touch a symbol on the control panel.
The signals are deactivated.
Activate the signals.
Refer to "Daily use" chapter.
The flexible induction cooking area does not heat up
the cookware.
The cookware is in the
wrong position on the flexible induction cooking area.
Place the cookware in the
correct position on the flexible induction cooking area.
The position of the cookware
depends on the activated
function or function mode.
Refer to "Flexible induction
cooking area" chapter.
The diameter of the bottom
of the cookware is incorrect
for the activated function or
function mode.
Use cookware with diameter
applicable to the activated
function or function mode.
Use cookware with diameter
smaller than 160 mm on a
single section of the flexible
induction cooking area.
Refer to "Flexible induction
cooking area" chapter.
comes on.
Automatic Switch Off operates.
Deactivate the hob and activate it again.
comes on.
The Child Safety Device or
the Lock function operates.
Refer to "Daily use" chapter.
comes on.
There is no cookware on the
zone.
Put cookware on the zone.
The cookware is incorrect.
Use the correct cookware.
Refer to “Hints and tips”
chapter.
ENGLISH
Problem
22
Possible cause
Remedy
The diameter of the bottom
of the cookware is too small
for the zone.
Use cookware with correct
dimensions.
Refer to “Hints and tips”
chapter.
The cookware does not cover the cross / square.
Cover the cross / square
fully.
Multi-Flexi mode operates.
One or more sections of the
function mode which operates are not covered by
cookware.
Place the cookware on the
correct number of sections of
the function mode which operates or change the function mode.
Refer to "Flexible induction
cooking area" chapter.
Pre-Set Cooking mode oper- Use only one pot.
ates. Two pots are placed
Refer to "Flexible induction
on the flexible induction
cooking area" chapter.
cooking area.
and a number come on.
There is an error in the hob.
Disconnect the hob from the
electrical supply for some
time. Disconnect the fuse
from the electrical system of
the house. Connect it again.
If
comes on again, speak
to an Authorised Service
Centre.
comes on.
There is an error in the hob
because a cookware boiled
dry. Automatic Switch Off
and the overheating protection for the zones operate.
Deactivate the hob. Remove
the hot cookware. After approximately 30 seconds, activate the zone again. If the
cookware was the problem,
the error message goes out.
Residual heat indicator can
stay on. Let the cookware
become sufficiently cool.
Check if your cookware is
compatible with the hob.
Refer to “Hints and tips”
chapter.
ENGLISH
23
If there is a fault, first try to find a solution to
the problem yourself. If you cannot find a
solution to the problem yourself, contact
your dealer or the After Sales Service.
If you operated the appliance
wrongly, or the installation was
not carried out by a registered
engineer, the visit from the After
Sales Service technician or
dealer may not take place free
of charge, even during the
warranty period.
Technical data
Rating Plate
Made in Germany
© Inter IKEA Systems B.V. 1999
Model HÖGKLASSIG Typ 60 GBD CL AU 7.4kW
PNC 949 594 493 00 S No .................... 220V-240V AC 50-60 Hz
21552
IKEA of Sweden AB
SE - 343 81 Älmhult
PQM
704.431.55
The graphic above represents the rating
plate of the appliance without serial
number, which is located at its underneath
surface of the casing.
230 V
DGT
to assist you better, by identifying precisely
your hob, in case you will need in future our
assistance. Thank you for your help!
Dear Customer, keep the additional rating
plate with the user manual. This will allow us
Energy efficiency
Product information according to EU 66/2014 valid for EU market only
Model identification
HÖGKLASSIG
704-431-55
Type of hob
Built-In Hob
Number of cooking zones
2
Number of cooking areas
1
Heating technology
Induction
Diameter of circular cooking zones (Ø)
Middle rear
Right front
21.0 cm
18.0 cm
ENGLISH
24
Lenght (L) and width (W) of Left
the cooking area
L 46.4 cm
W 24.7 cm
Energy consumption per
cooking zone (EC electric
cooking)
Middle rear
Right front
186.4 Wh / kg
180.3 Wh / kg
Energy consumption of the
cooking area (EC electric
cooking)
Left
184.7 Wh / kg
Energy consumption of the
hob (EC electric hob)
EN 60350-2 - Household electric cooking
appliances - Part 2: Hobs - Methods for
measuring performance
Energy saving
You can save energy during everyday
cooking if you follow below hints.
• When you heat up water, use only the
amount you need.
184.1 Wh / kg
• If it is possible, always put the lids on the
cookware.
• Before you activate the cooking zone put
the cookware on it.
• Put the smaller cookware on the smaller
cooking zones.
• Put the cookware directly in the centre of
the cooking zone.
• Use the residual heat to keep the food
warm or to melt it.
Environmental concerns
Recycle materials with the symbol . Put
the packaging in relevant containers to
recycle it. Help protect the environment and
human health by recycling waste of
electrical and electronic appliances. Do not
dispose of appliances marked with the
symbol with the household waste. Return
the product to your local recycling facility or
contact your municipal office.
IKEA guarantee
How long is the IKEA guarantee valid?
This guarantee is valid for five (5) years two (2) years if the appliance is named
LAGAN or TILLREDA - from the original
date of purchase of your appliance at IKEA
or from the installation date with maximum
limit of three months from the purchase
date. The original sales receipt, is required
as proof of purchase. If service work is
carried out under guarantee, this will not
extend the guarantee period for the
appliance. Once a warranted product has
been replaced, the replaced product
warranty will be valid for the balance
ENGLISH
period from date of original purchase
invoice.
Who will execute the service?
IKEA service provider will provide the
service through its own service operations
or authorized service partner network.
What does this guarantee cover?
• The guarantee covers faults of the
appliance, which have been caused by
faulty construction or material faults from
the date of purchase from IKEA or from
the installation date with maximum limit
of three months from the purchase date.
• This guarantee applies to domestic use
only.
• The exceptions are specified under the
headline “What is not covered under this
guarantee?” Within the guarantee
period.
• The costs to remedy the fault e.g. repairs,
parts, labour and travel will be covered,
provided that the appliance is accessible
for repair without special expenditure.
On these conditions the respective local
regulations are applicable.
• Replaced parts become the property of
IKEA.
• In case of non-repairable product, the
retail value of the replacement will not
exceed the purchase price that was paid
by the customer
What will IKEA do to correct the problem?
• IKEA appointed Service Provider will
examine the product and decide, at its
sole discretion, if it is covered under this
guarantee. If considered covered, IKEA
Service Provider or its authorized service
partner through its own service
operations, will then, at its sole
discretion, either repair the defective
product or replace it with the same or a
comparable product.
What is not covered under this
guarantee?
• Normal wear and tear.
25
• Deliberate or negligent damage,
damage caused by failure to observe
operating instructions, incorrect
installation or by connection to the
wrong voltage, damage caused by
chemical or electro-chemical reaction,
rust, corrosion or water damage
including but not limited to damage
caused by excessive lime in the water
supply, damage caused by abnormal
environmental conditions.
• Consumable parts including batteries
and lamps.
• Non-functional and decorative parts
which do not affect normal use of the
appliance, including any scratches and
possible colour differences.
• Accidental damage caused by foreign
objects or substances and cleaning or
unblocking of filters, drainage systems or
soap drawers.
• Damage to the following parts: ceramic
glass, accessories, crockery and cutlery
baskets, feed and drainage pipes, seals,
lamps and lamp covers, screens, knobs,
casings and parts of casings. Unless such
damages can be proved to have been
caused by production faults.
• Cases where no fault could be found
during a technician’s visit.
• Repairs not carried out by our appointed
service providers and/or an authorized
service contractual partner or where
non-original parts have been used.
• Repairs caused by installation which is
faulty or not according to specification.
• The use of the appliance in a nondomestic environment i.e. professional
use.
• Damage resulting from power outage,
power surges or dips, fluctuating voltage
or improper voltage All workout parts
are not covered by the guarantee e.g.:
filters and cleanliness.
• Transportation damages. If a customer
transports the product to his home or
another address, IKEA is not liable for
any damage that may occur during
ENGLISH
transport. However, if IKEA delivers the
product to the customer’s delivery
address, then damage to the product
that occurs during this delivery will be
covered by IKEA.
• Cost for carrying out the initial
installation of the IKEA appliance.
However, if an IKEA service provider or
its authorized service partner repairs or
replaces the appliance under the terms
of this guarantee, the service provider or
its authorized service partner will reinstall the repaired appliance or install
the replacement, if necessary.
• All plumping and electrical installation,
are not the responsibility of IKEA, and
customer must complete these work
before the execution work.
How country law applies
The IKEA guarantee gives You specific legal
rights, which covers or exceed local
demands. However these conditions do not
limit in any way consumer rights described
in the local legislation.
Area of validity
This warranty is valid only in the country
where the product has been purchased; the
services will be provided in the framework
of the guarantee conditions.
An obligation to carry out services in the
framework of the guarantee exists only if
the appliance complies and is installed in
accordance with:
• the technical specifications of the country
in which the guarantee claim is made;
• the Assembly Instructions and User
Manual Safety Information;
The dedicated After Sales Service for
IKEA appliances:
Please don’t hesitate to contact IKEA
appointed After Sales Service Provider to:
• make a service request under this
guarantee;
26
• ask for clarifications on installation of the
IKEA appliance in the dedicated IKEA
kitchen furniture;
• ask for clarification on functions of IKEA
appliances.
To ensure that we provide you with the best
assistance, please read carefully the
Assembly Instructions and/or the User
Manual before contacting us.
How to reach us if You need our service
Please refer to the last page of this manual
for the full list of IKEA appointed contacts
and relative national phone numbers.
In order to provide You with a
quicker service, we recommend
that You use the specific phone
numbers listed at the end of this
manual. Always refer to the
numbers listed in the booklet of
the specific appliance You need
an assistance for. Before calling
us, assure that You have to hand
the IKEA article number (8 digit
code) and the Serial Number (8
digit code that can be found on
the rating plate) for the
appliance of which you need our
assistance.
SAVE THE SALES RECEIPT! It is
your proof of purchase and
required for the guarantee to
apply. The sales receipt also
reports the IKEA name and
article number (8 digit code) for
each of the appliances you have
purchased.
27
UNITED ARAB EMIRATES
Toll free:
: ‫رﻗﻢ ﻣﺠﺎﻧﻲ‬
: ‫ﻣﻮﻗﻊ اﻹﻧﺘﺮﻧﺖ‬
8 004 532
Web:
www.IKEA.com
QATAR
Toll free:
8 004 532
Web:
e-mail:
www.IKEA.qa
Ikea_qatar@alfuttaim.com
: ‫رﻗﻢ ﻣﺠﺎﻧﻲ‬
: ‫ﻣﻮﻗﻊ اﻹﻧﺘﺮﻧﺖ‬
: ‫اﻟﺒﺮﻳﺪ اﻹﻟﻜﺘﺮوﻧﻲ‬
EGYPT
Hotline:
16576
Web:
www.IKEA.eg
e-mail: IkeaCairo.customerservice@alfuttaim.com
: ‫اﻟﺨﻂ اﻟﺴﺎﺧﻦ‬
: ‫ﻣﻮﻗﻊ اﻹﻧﺘﺮﻧﺖ‬
: ‫اﻟﺒﺮﻳﺪ اﻹﻟﻜﺘﺮوﻧﻲ‬
STATE OF KUWAIT
Contact centre:
: ‫ﻣﺮﻛﺰ اﻻﺗﺼﺎل‬
: ‫ﻣﻮﻗﻊ اﻹﻧﺘﺮﻧﺖ‬
: ‫اﻟﺒﺮﻳﺪ اﻹﻟﻜﺘﺮوﻧﻲ‬
+965 18 40 40 8
Web:
www.IKEA.com.kw
e-mail:
info@IKEA.com.kw
JORDAN
Contact centre:
www.IKEA.jo
: ‫ﻣﺮﻛﺰ اﻻﺗﺼﺎل‬
: ‫ﻣﻮﻗﻊ اﻹﻧﺘﺮﻧﺖ‬
92000-4532
: ‫ﻣﺮﻛﺰ اﻻﺗﺼﺎل‬
+962 6 400 1000
Web:
KINGDOM OF SAUDI ARABIA
Contact centre:
Our phone lines are
open:
Saturday - Thursday
Friday
: ‫ﺧﻄﻮط اﻟﮭﺎﺗﻒ ﻟﺪﻳﻨﺎ ﻣﻔﺘﻮﺣﺔ‬
‫ اﻟﺨﻤﯿﺲ‬- ‫اﻟﺴﺒﺖ‬
‫ﻳﻮم اﻟﺠﻤﻌﺔ‬
09:00 AM - 10:00 PM
2:00 PM - 10:00 PM
BAHRAIN
Contact centre:
Our telephone lines are
open all day
: ‫ﻣﺮﻛﺰ اﻻﺗﺼﺎل‬
80001120
‫ﺧﻄﻮط اﻟﮭﺎﺗﻒ ﻟﺪﻳﻨﺎ ﻣﻔﺘﻮﺣﺔ طﻮال اﻟﯿﻮم‬
09:00 AM - 10:00 PM
*
867357497-A-292019
© Inter IKEA Systems B.V. 2019
21552
AA-2109591-2
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising