Electrolux | EGH7459GOX | User manual | Electrolux EGH7459GOX User Manual

Electrolux EGH7459GOX User Manual
EGH7459GOX
EN
Hob
User Manual
2
www.electrolux.com
CONTENTS
1. SAFETY INFORMATION....................................................................................2
2. SAFETY INSTRUCTIONS..................................................................................4
3. INSTALLATION.................................................................................................. 7
4. PRODUCT DESCRIPTION.............................................................................. 11
5. DAILY USE....................................................................................................... 11
6. USING THE ACCESSORIES........................................................................... 13
7. HINTS AND TIPS............................................................................................. 14
8. CARE AND CLEANING....................................................................................15
9. TROUBLESHOOTING......................................................................................16
10. TECHNICAL DATA.........................................................................................17
11. ENERGY EFFICIENCY.................................................................................. 19
WE’RE THINKING OF YOU
Thank you for purchasing an Electrolux appliance. You’ve chosen a product that
brings with it decades of professional experience and innovation. Ingenious and
stylish, it has been designed with you in mind. So whenever you use it, you can
be safe in the knowledge that you’ll get great results every time.
Welcome to Electrolux.
Visit our website for:
Get usage advice, brochures, trouble shooter, service information:
www.electrolux.com/webselfservice
Register your product for better service:
www.registerelectrolux.com
Buy Accessories, Consumables and Original spare parts for your appliance:
www.electrolux.com/shop
CUSTOMER CARE AND SERVICE
Always use original spare parts.
When contacting our Authorised Service Centre, ensure that you have the
following data available: Model, PNC, Serial Number.
The information can be found on the rating plate.
Warning / Caution-Safety information
General information and tips
Environmental information
Subject to change without notice.
1.
SAFETY INFORMATION
Before the installation and use of the appliance, carefully
read the supplied instructions. The manufacturer is not
responsible for any injuries or damages that are the
ENGLISH
3
result of incorrect installation or usage. Always keep the
instructions in a safe and accessible location for future
reference.
1.1 Children and vulnerable people safety
•
•
•
•
•
•
•
•
This appliance can be used by children aged from 8
years and above and persons with reduced physical,
sensory or mental capabilities or lack of experience
and knowledge if they have been given supervision or
instruction concerning the use of the appliance in a
safe way and understand the hazards involved.
Children between 3 and 8 years of age and persons
with very extensive and complex disabilities shall be
kept away unless continuously supervised.
Children of less than 3 years of age should be kept
away unless continuously supervised.
Do not let children play with the appliance.
Keep all packaging away from children and dispose of
it appropriately.
Keep children and pets away from the appliance when
it operates or when it cools down. Accessible parts are
hot.
If the appliance has a child safety device, it should be
activated.
Children shall not carry out cleaning and user
maintenance of the appliance without supervision.
1.2 General Safety
•
•
•
WARNING: The appliance and its accessible parts
become hot during use. Care should be taken to avoid
touching heating elements.
Do not operate the appliance by means of an external
timer or separate remote-control system.
WARNING: Unattended cooking on a hob with fat or
oil can be dangerous and may result in fire.
4
www.electrolux.com
•
•
•
•
•
•
•
•
•
NEVER try to extinguish a fire with water, but switch
off the appliance and then cover flame e.g. with a lid
or a fire blanket.
CAUTION: The cooking process has to be supervised.
A short term cooking process has to be supervised
continuously.
WARNING: Danger of fire: Do not store items on the
cooking surfaces.
Metallic objects such as knives, forks, spoons and lids
should not be placed on the hob surface since they
can get hot.
Do not use a steam cleaner to clean the appliance.
If the supply cord is damaged, it must be replaced by
the manufacturer, an authorized Service or similarly
qualified persons in order to avoid a hazard.
Where the appliance is directly connected to the
power supply, an all-pole isolating switch with a
contact gap is required. Complete disconnection in
compliance with the conditions specified in
overvoltage category III must be guaranteed. The
earth cable is excluded from this.
When you route the mains cable, make sure that the
cable doesn't come into direct contact (for example
using insulating sleeving) with parts that can reach
temperatures of more than 50°C above room
temperature.
WARNING: Use only hob guards designed by the
manufacturer of the cooking appliance or indicated by
the manufacturer of the appliance in the instructions
for use as suitable or hob guards incorporated in the
appliance. The use of inappropriate guards can cause
accidents.
2. SAFETY INSTRUCTIONS
This appliance is suitable for the
following markets: IT
ENGLISH
2.1 Installation
WARNING!
Only a qualified person must
install this appliance.
WARNING!
Risk of injury or damage to
the appliance.
•
•
•
•
•
•
•
•
•
•
Remove all the packaging.
Do not install or use a damaged
appliance.
Follow the installation instructions
supplied with the appliance.
Keep the minimum distance from
other appliances and units.
Always take care when moving the
appliance as it is heavy. Always use
safety gloves and enclosed footwear.
Seal the cut surfaces with a sealant to
prevent moisture to cause swelling.
Protect the bottom of the appliance
from steam and moisture.
Do not install the appliance adjacent
to a door or under a window. This
prevents hot cookware falling from the
appliance when the door or the
window is opened.
If the appliance is installed above
drawers make sure that the space,
between the bottom of the appliance
and the upper drawer, is sufficient for
air circulation.
The bottom of the appliance can get
hot. Make sure to install a noncombustible separation panel under
the appliance to prevent access to the
bottom.
2.2 Electrical Connection
WARNING!
Risk of fire and electric
shock.
•
•
•
•
All electrical connections should be
made by a qualified electrician.
The appliance must be earthed.
Before carrying out any operation
make sure that the appliance is
disconnected from the power supply.
Make sure that the parameters on the
rating plate are compatible with the
electrical ratings of the mains power
supply.
•
•
•
•
•
•
•
•
•
•
•
•
•
•
5
Make sure the appliance is installed
correctly. Loose and incorrect
electricity mains cable or plug (if
applicable) can make the terminal
become too hot.
Use the correct electricity mains
cable.
Do not let the electricity mains cable
tangle.
Make sure that a shock protection is
installed.
Use the strain relief clamp on the
cable.
Make sure the mains cable or plug (if
applicable) does not touch the hot
appliance or hot cookware, when you
connect the appliance to the near
sockets.
Do not use multi-plug adapters and
extension cables.
Make sure not to cause damage to
the mains plug (if applicable) or to the
mains cable. Contact our Authorised
Service Centre or an electrician to
change a damaged mains cable.
The shock protection of live and
insulated parts must be fastened in
such a way that it cannot be removed
without tools.
Connect the mains plug to the mains
socket only at the end of the
installation. Make sure that there is
access to the mains plug after the
installation.
If the mains socket is loose, do not
connect the mains plug.
Do not pull the mains cable to
disconnect the appliance. Always pull
the mains plug.
Use only correct isolation devices: line
protecting cut-outs, fuses (screw type
fuses removed from the holder), earth
leakage trips and contactors.
The electrical installation must have
an isolation device which lets you
disconnect the appliance from the
mains at all poles. The isolation
device must have a contact opening
width of minimum 3 mm.
2.3 Gas connection
•
•
All gas connections should be made
by a qualified person.
Before installation, make sure that the
local distribution conditions (nature of
6
www.electrolux.com
•
•
•
the gas and gas pressure) and the
adjustment of the appliance are
compatible.
Make sure that there is air circulation
around the appliance.
The information about the gas supply
is on the rating plate.
This appliance is not connected to a
device, which evacuates the products
of combustion. Make sure to connect
the appliance according to current
installation regulations. Pay attention
to requirements regarding adequate
ventilation.
2.4 Use
WARNING!
Risk of injury, burns and
electric shock.
•
•
•
•
•
•
•
•
•
•
Remove all the packaging, labelling
and protective film (if applicable)
before first use.
This appliance is for household use
only.
Do not change the specification of this
appliance.
Make sure that the ventilation
openings are not blocked.
Do not let the appliance stay
unattended during operation.
Set the cooking zone to “off” after
each use.
Do not put cutlery or saucepan lids on
the cooking zones. They can become
hot.
Do not operate the appliance with wet
hands or when it has contact with
water.
Do not use the appliance as a work
surface or as a storage surface.
When you place food into hot oil, it
may splash.
•
WARNING!
Risk of damage to the
appliance.
•
•
•
•
•
•
•
•
•
•
•
•
•
WARNING!
Risk of fire and explosion
•
•
•
Fats and oil when heated can release
flammable vapours. Keep flames or
heated objects away from fats and
oils when you cook with them.
The vapours that very hot oil releases
can cause spontaneous combustion.
Used oil, that can contain food
remnants, can cause fire at a lower
temperature than oil used for the first
time.
Do not put flammable products or
items that are wet with flammable
products in, near or on the appliance.
•
•
Do not keep hot cookware on the
control panel.
Do not let cookware to boil dry.
Be careful not to let objects or
cookware fall on the appliance. The
surface can be damaged.
Do not activate the cooking zones
with empty cookware or without
cookware.
Do not put aluminium foil on the
appliance.
Use only stable cookware with the
correct shape and diameter larger
than the dimensions of the burners.
Make sure cookware is centrally
positioned on the burners.
Do not use large cookware that
overlap the edges of the appliance.
This can cause damage to the
worktop surface.
Make sure the flame does not go out
when you quickly turn the knob from
the maximum to the minimum
position.
Use only the accessories supplied
with the appliance.
Do not install a flame diffuser on the
burner.
The use of a gas cooking appliance
results in the production of heat and
moisture. Provide good ventilation in
the room where the appliance is
installed.
Prolonged intensive use of the
appliance may call for additional
ventilation, for example opening of a
window, or more effective ventilation,
for example increasing the level of
mechanical ventilation where present.
This appliance is for cooking
purposes only. It must not be used for
other purposes, for example room
heating.
Do not let acid liquids, for example
vinegar, lemon juice or limescale
ENGLISH
•
remover, touch the hob. This can
cause matt patches.
Discoloration of the enamel or
stainless steel has no effect on the
performance of the appliance.
2.5 Care and cleaning
WARNING!
Do not remove the buttons,
knobs or gaskets from the
control panel. Water may get
inside the appliance and
cause damage.
•
•
•
•
•
Clean the appliance regularly to
prevent the deterioration of the
surface material.
Deactivate the appliance and let it
cool down before you clean it.
Disconnect the appliance from the
electrical supply before maintenance.
Do not use water spray and steam to
clean the appliance.
Clean the appliance with a moist soft
cloth. Only use neutral detergents. Do
•
7
not use any abrasive products,
abrasive cleaning pads, solvents or
metal objects.
Do not clean the burners in the
dishwasher.
2.6 Service
•
•
To repair the appliance contact an
Authorised Service Centre.
Use original spare parts only.
2.7 Disposal
WARNING!
Risk of injury or suffocation.
•
•
•
•
Contact your municipal authority for
information on how to discard the
appliance correctly.
Disconnect the appliance from the
mains supply.
Cut off the mains electrical cable
close to the appliance and dispose of
it.
Flat the external gas pipes.
3. INSTALLATION
WARNING!
Refer to Safety chapters.
3.1 Before the installation
Before you install the hob, write down the
information bellow from the rating plate.
The rating plate is on the bottom of the
hob.
Model .......................................
PNC .........................................
Serial number ...........................
3.2 Gas Connection
WARNING!
The following instructions
about installation,
maintenance and ventilation
must be carried out by
qualified personnel in
compliance with the
regulation in force (UNI-CIG
7129 - 7131). Make sure that
the kitchen is well ventilated:
keep natural ventilation
holes open (at least 100
cm²) or install a mechanical
extractor hood.
Choose fixed connections or use a
flexible pipe in stainless steel in
compliance with the regulation in force. If
you use flexible metallic pipes, be careful
they do not come in touch with mobile
parts or they are not squeezed. Also be
careful when the hob is put together with
an oven.
8
www.electrolux.com
Make sure that the gas
supply pressure of the
appliance obeys the
recommended values.
If the supplied pressure has not the
specified value, it is necessary to
assemble a proper pressure regulator in
compliance with the standard UNI EN 88.
For Liquid Gas (LPG) the use of pressure
regulator is allowed only if they are in
compliance with UNI EN 12864. The
adjustable connection is fixed to the
comprehensive ramp by means of a
threaded nut G 1/2". Screw the parts
without force, adjust the connection in
the necessary direction and tighten
everything.
ones which are necessary for the
type of gas you use (see table in
"Technical Data" chapter).
4. Assemble the parts, follow the same
procedure backwards.
5. Replace the rating plate (it is near the
gas supply pipe) with the one for the
new type of gas supply. You can find
this plate in the package supplied
with the appliance.
If the supply gas pressure is changeable
or different from the necessary pressure,
you must fit an applicable pressure
adjuster on the gas supply pipe.
3.4 Adjustment of minimum
level
To adjust the minimum level of the
burners:
1. Light the burner.
2. Turn the knob on the minimum
position.
3. Remove the knob.
4. With a thin screwdriver, adjust the
bypass screw position (A).
A
A
B C
A. End of shaft with nut
B. Washer supplied with the appliance
C. Elbow supplied with the appliance
Rigid connection:
Carry out connection by using metal rigid
pipes (copper with mechanical end)
(UNI-CIG 7129).
Flexible connection:
Use a flexible pipe in stainless steel
(UNI-CIG 9891) with a maximum length 2
m.
WARNING!
When installation is
complete, make sure that
the seal of each pipe fitting
is correct. Use a soapy
solution, not a flame!
5. If you change:
• from natural gas G20 20 mbar to
liquid gas, fully tighten the bypass
screw in.
• from liquid gas to natural gas G20
20 mbar, undo the bypass screw
approximately 1/4 of a turn (1/2 of
a turn for Multi Crown burner).
WARNING!
Make sure the flame does
not go out when you quickly
turn the knob from the
maximum position to the
minimum position.
3.3 Injectors replacement
1. Remove the pan supports.
2. Remove the caps and crowns of the
burner.
3. With a socket spanner 7 remove the
injectors and replace them with the
3.5 Electrical connection
•
Make sure that the rated voltage and
type of power on the rating plate
ENGLISH
agree with the voltage and the power
of the local power supply.
• This appliance is supplied with a
mains cable. It has to be supplied with
a correct plug which can hold the load
that the rating plate rates. Make sure
that you install the plug in a correct
socket.
• Always use a correctly installed
shockproof socket.
• Make sure that there is an access to
the mains plug after the installation.
• Do not pull the mains cable to
disconnect the appliance. Always pull
the mains plug.
• There is a risk of fire when the
appliance is in connection with an
extension cable, an adapter or a
multiple connection. Make sure that
the ground connection agrees with the
standards and regulations.
• Do not let the power cable to heat up
to a temperature higher than 90° C.
To prevent contact between the cable
and the appliance below the hob use the
clamps which are on the side of the
cabinet.
A
3.7 Assembly
1.
2.
3.
min.
170 mm
min.
650 mm
min.
55 mm
30 mm
480+02 mm
A. Rigid copper pipe or flexible pipe of
stainless steel
3.6 Connection cable
To replace the connection cable use only
the special cable or its equivalent. The
cable type is: H03V2V2-F T90.
Make sure that the cable section is
applicable to the voltage and the working
temperature. The yellow / green earth
wire must be approximately 2 cm longer
than the brown (or black) phase wire.
4.
560+02 mm
9
10
www.electrolux.com
10.
5.
CAUTION!
Install the appliance only on
a worktop with flat surface.
6.
3.8 Installing hob under the
hood
If you install the hob under a
hood, please see the
installation instructions of the
hood for the minimum
distance between the
appliances.
7.
3.9 Possibilities for insertion
The panel installed below the hob must
be easy to remove and let an easy
access in case a technical assistance
intervention is necessary.
8.
Kitchen unit with door
A
B
9.
min 6 mm
A) supplied seal
B) supplied brackets
A
B
min 20 mm
(max 150 mm)
60 mm
A. Removable panel
min 30 mm
ENGLISH
B. Space for connections
11
safety reasons and to let easy remove
oven from the unit.
Kitchen unit with oven
The electrical connection of the hob and
the oven must be installed separately for
4. PRODUCT DESCRIPTION
4.1 Cooking surface layout
1
2
3
1
2
3
4
5
Multi Crown burner
Rapid burner
Bridge burner - Semi Rapid
Auxiliary burner
Control knobs
4
5
4.2 Control knob
Symbol
Description
no gas supply / off posi‐
tion
ignition position / maxi‐
mum gas supply
minimum gas supply
4.3 Accessories
Plancha
5. DAILY USE
WARNING!
Refer to Safety chapters.
The plancha can only be
placed over the bridge
burner.
You can use the plancha to grilling food.
12
www.electrolux.com
5.1 Burner overview
5.2 Ignition of the burner
$
%
&
'
$
%
&
'
A.
B.
C.
D.
Burner cap
Burner crown
Ignition candle
Thermocouple
A
B
C
D
A.
B.
C.
D.
Burner cap
Burner crown
Ignition candle
Thermocouple
Always light the burner
before you put on the
cookware.
WARNING!
Be very careful when you
use open fire in the kitchen
environment. The
manufacturer declines any
responsibility in case of the
flame misuse.
1. Push the control knob down and turn
it counterclockwise to the maximum
gas supply position ( ).
2. Keep the control knob pushed for
equal or less than 10 seconds. This
lets the thermocouple warm up. If
not, the gas supply is interrupted.
3. Adjust the flame after it is regular.
If after some tries the burner
does not light, check if the
crown and its cap are in
correct positions.
WARNING!
Do not keep the control knob
pushed for more than 15
seconds. If the burner does
not light after 15 seconds,
release the control knob,
turn it into off position and try
to light the burner again after
minimum 1 minute.
CAUTION!
In the absence of electricity
you can ignite the burner
without electrical device; in
this case approach the
burner with a flame, turn the
control knob counterclockwise to maximum gas
supply position and push it
down. Keep the control knob
pushed for equal or less
than 10 seconds to let the
thermocouple warm up.
ENGLISH
If the burner accidentally
goes out, turn the control
knob to the off position and
try to light the burner again
after minimum 1 minute.
13
5.3 Turning the burner off
To put the flame out, turn the knob to the
off position
.
WARNING!
Always turn the flame down
or switch it off before you
remove the pans from the
burner.
The spark generator can
start automatically when you
switch on the mains, after
installation or a power cut. It
is normal.
The hob is supplied with the
progressive valves. They
make the flame regulation
more precise.
6. USING THE ACCESSORIES
WARNING!
Refer to Safety chapters.
6.1 Using the bridge burner
CAUTION!
Always place the burners
before turning on the hob.
•
Put one bridge cap and crown on
the rear position and normal sized
cap and crown on the front
position.
•
Put both normal sized caps on the
both normal sized burner crowns.
1. Remove the pan supports.
2. Remove the burner caps and crowns.
3. Use the bridge burner in 4 different
combinations.
• Put both bridge caps on the both
bridge burner crowns.
•
Put one bridge cap and crown on
the front position and normal
sized cap and crown on the rear
position.
After each combination put the pan
supports on the hob surface.
14
www.electrolux.com
6.2 Plancha
CAUTION!
Always place the plancha on
the bridge burner before
turning on the burner.
WARNING!
Do not put the plancha on
the reverse side.
1. Place the plancha on the center gas
burners, on the pan supports.
2. Preheat the plancha for 5 minutes on
medium setting.
Clean the plancha after each use with a
stiff brush and hot water only.
Warm up the plancha for 10
minutes at the maximum
setting, put the food on, then
turn down at the minimum
setting during the cooking.
Keeping warm of the
plancha is very efficient.
6.3 Before first use
1. Wash the plancha in hot water. Rinse
and then dry completely.
2. Apply a thin coat of vegetable oil to
the entire surface.
3. Preheat the plancha for 5 minutes
with the both burners at the minimum
setting.
4. When the plancha is cold dry the oil
with a towel.
5. Repeat the procedure if needed to
obtain the best cooking performance.
7. HINTS AND TIPS
WARNING!
Refer to Safety chapters.
7.1 Cookware
CAUTION!
Do not use cast iron pans,
clay or earthenware pots,
grill or toaster plates. The
stainless steel can become
tarnished if it is too much
heated.
WARNING!
Do not put the same pan on
two burners. Use the same
pan on two burners only for
bridge burner.
WARNING!
Do not put unstable or
damaged pots on the burner
to prevent spills and injuries.
CAUTION!
Make sure that the bottoms
of pots do not stand too
close to the control knob,
otherwise the flame heats
the control knob up.
CAUTION!
Make sure that pot handles
are not above the front edge
of the cooktop.
CAUTION!
Make sure that the pots are
placed centrally on the
burner in order to get the
maximum stability and a
lower gas consumption.
7.2 Diameters of cookware
Use cookware with
diameters applicable to the
size of burners.
ENGLISH
Burner
Diameter of
cookware
(mm)
Burner
Multi Crown
180 - 260
Semi-rapid (front right) 120 - 220
Rapid
160 - 260
Auxiliary
Semi-rapid (rear right)
120 - 240
15
Diameter of
cookware
(mm)
80 - 180
8. CARE AND CLEANING
WARNING!
Refer to Safety chapters.
8.1 General information
•
•
Clean the hob after each use.
Always use cookware with a clean
base.
• Scratches or dark stains on the
surface have no effect on how the hob
operates.
• Use a special cleaner suitable for the
surface of the hob.
Stainless steel
•
•
•
•
Wash stainless steel parts with water,
and then dry them with a soft cloth.
To remove burnt food, fat and
stubborn stains let them soak in a
small amount of mild detergent for a
few minutes before cleaning.
Use cleaning products designed
specifically for cleaning stainless steel
in order to protect the steel surfaces.
Do not use cleaning products
containing corrosive chemicals such
as chlorides, do not clean the surface
with disinfectants, stain or rust
removers and immersion cleaners.
8.2 Pan supports
The pan supports are not
resistant to washing in a
dishwasher. They must be
washed by hand.
1. Remove the pan supports to easily
clean the hob.
Be very careful when
you replace the pan
supports to prevent the
hob top from damage.
2. The enamel coating occasionally can
have rough edges, so be careful
when you wash the pan supports by
hand and dry them. If necessary,
remove stubborn stains with a paste
cleaner.
3. After you clean the pan supports,
make sure that they are in correct
positions.
4. For the burner to operate correctly,
make sure that the arms of the pan
supports are aligned with the centre
of the burner.
16
www.electrolux.com
8.3 Cleaning the hob
Remove immediately: melted plastic,
plastic foil, sugar and food with sugar,
otherwise, the dirt can cause damage
to the hob. Take care to avoid burns.
• Remove when the hob is
sufficiently cool: limescale rings,
water rings, fat stains, shiny metallic
discoloration. Clean the hob with a
moist cloth and a non-abrasive
detergent. After cleaning, wipe the
hob dry with a soft cloth.
• To clean the enamelled parts, caps
and crowns, wash them with warm
soapy water and dry them carefully
before you put them back on.
Easy Clean Coating
• To clean the hob remove any food
remains from the cooking surface.
• Clean the hob with warm water and a
non-abrasive detergent.
• To dry the hob after cleaning wipe it
with a soft cloth or chamois leather.
• To clean the Easy Clean surface
everyday use a soft cloth moistened
with water or a glass cleaner. We do
not recommend the use of paper
towels which can leave streaks on the
surface.
WARNING!
Harsh detergents and hard
water can leave stains on
the stainless steel surface.
•
8.4 Cleaning the spark plug
This feature is obtained through a
ceramic ignition candle with a metal
electrode. Keep these components well
clean to prevent difficult lighting and
check that the burner crown holes are
not obstructed.
8.5 Plancha
•
•
•
Do not use cold water while the
plancha is still hot.
Use a stiff brush and not aggressive
detergents to clean the surface.
If it is difficult to remove the dirt, keep
the plancha in hot water for few
minutes, then wash normally.
8.6 Periodic maintenance
Speak to your local Authorised Service
Centre periodically to check the
conditions of the gas supply pipe and the
pressure adjuster, if fitted.
9. TROUBLESHOOTING
WARNING!
Refer to Safety chapters.
9.1 What to do if...
Problem
Possible cause
Remedy
There is no spark when
you try to activate the
spark generator.
The hob is not connected
to an electrical supply or it
is connected incorrectly.
Check if the hob is correct‐
ly connected to the electri‐
cal supply.
The fuse is blown.
Make sure that the fuse is
the cause of the malfunc‐
tion. If the fuse is blown
again and again, contact a
qualified electrician.
Burner cap and crown are
placed incorrectly.
Place the burner cap and
crown correctly.
ENGLISH
Problem
Possible cause
17
Remedy
The flame extinguishes im‐ Thermocouple is not heat‐
mediately after ignition.
ed up sufficiently.
After lightning the flame,
keep the knob pushed for
equal or less than 10 sec‐
onds.
The flame ring is uneven.
Make sure that the injector
is not blocked and the
burner crown is clean.
Burner crown is blocked
with food residues.
9.2 If you cannot find a
solution...
during the warranty period. The
instructions about the Service Centre
and conditions of guarantee are in the
guarantee booklet.
If you cannot find a solution to the
problem yourself, contact your dealer or
an Authorised Service Centre. Give the
data from the rating plate. Make sure,
you operated the hob correctly. If not the
servicing by a service technician or
dealer will not be free of charge, also
A
9.3 Labels supplied with the
accessories bag
Stick the adhesive labels as indicated
below:
B
MOD.
MOD.
PROD.NO.
PROD.NO.
SER.NO
SER.NO
DATA
DATA
C
MOD.
PROD.NO.
SER.NO.
0049
03 IT
MADE IN ITALY
A. Stick it on Guarantee Card and send
this part (if applicable).
B. Stick it on Guarantee Card and keep
this part (if applicable).
C. Stick it on instruction booklet.
10. TECHNICAL DATA
10.1 Hob dimensions
Width
TYPE
IP20
745 mm
18
www.electrolux.com
Depth
510 mm
10.2 Bypass diameters
BURNER
Ø BYPASS 1/100 mm
Multi Crown
57
Rapid
42
Semi-rapid
- Bridge burner
35
Auxiliary
28
10.3 Other technical data
TOTAL POW‐
ER:
Electric supply:
Gas original:
G20 (2H) 20 mbar
11,7 kW
Gas replace‐
ment:
G30 (3+) 28-30 mbar
832 g/h
G31 (3+) 37 mbar
818 g/h
220-240 V ~ 50-60 Hz
Appliance cate‐ II2H3+
gory:
Gas connec‐
tion:
G 1/2"
Appliance
class:
3
10.4 Gas burners for NATURAL GAS G20 20 mbar
BURNER
NORMAL POWER MINIMUM POWER
kW
kW
INJECTOR MARK
Multi Crown
4,0
1,4
146
Rapid
3,0
0,75
119
Semi-rapid
- Bridge burner
1,85
0,6
92
Auxiliary
1,0
0,33
70
ENGLISH
19
10.5 Gas burners for LPG G30/G31 28-30/37 mbar
BURNER
NORMAL
POWER
kW
MINIMUM
POWER
kW
INJECTOR
MARK
NOMINAL GAS FLOW g/h
G30 28-30
mbar
G31 37 mbar
Multi Crown 3,65
1,4
095
265
261
Rapid
2,8
0,95
86
204
200
Semi-rapid
- Bridge
burner
2,0
0,6
71
145
143
Auxiliary
1,0
0,33
50
73
71
11. ENERGY EFFICIENCY
11.1 Product information according to EU 66/2014
Model identification
EGH7459GOX
Type of hob
Built-in hob
Number of gas burners
5
Energy efficiency per gas burner
(EE gas burner)
Energy efficiency for the gas hob
(EE gas hob)
Left middle - Multi Crown
55.4%
Centre rear - Semi-rapidBridge burner
55.1%
Centre front - Semi-rapidBridge burner
53.0%
Right rear - Rapid
56.9%
Right front - Auxiliary
not applicable
55.1%
EN 30-2-1: Domestic cooking appliances burning gas - Part 2-1 : Rational use of
energy - General
11.2 Energy saving
•
•
•
•
•
•
•
Before use, make sure that the burners and pan supports are assembled correctly.
Use cookware with diameters applicable to the size of burners.
Center the pot on the burner.
When you heat up water, use only the amount you need.
If it is possible, always put the lids on the cookware.
When the liquid starts to boil, turn down the flame to barely simmer the liquid.
If it is possible, use a pressure cooker. Refer to its user manual.
20
www.electrolux.com
12. ENVIRONMENTAL CONCERNS
Recycle materials with the symbol .
Put the packaging in relevant containers
to recycle it. Help protect the
environment and human health by
recycling waste of electrical and
electronic appliances. Do not dispose of
*
appliances marked with the symbol
with the household waste. Return the
product to your local recycling facility or
contact your municipal office.
ENGLISH
21
22
www.electrolux.com
ENGLISH
23
867345994-C-262019
www.electrolux.com/shop
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising