Electrolux | KGG6438K | User manual | Electrolux KGG6438K User Manual

Electrolux KGG6438K User Manual
KGG6438K
EN
Hob
User Manual
2
www.electrolux.com
CONTENTS
1. SAFETY INFORMATION....................................................................................2
2. SAFETY INSTRUCTIONS..................................................................................5
3. INSTALLATION.................................................................................................. 7
4. PRODUCT DESCRIPTION.............................................................................. 12
5. DAILY USE....................................................................................................... 13
6. HINTS AND TIPS............................................................................................. 15
7. CARE AND CLEANING....................................................................................17
8. TROUBLESHOOTING......................................................................................18
9. TECHNICAL DATA...........................................................................................19
WE’RE THINKING OF YOU
Thank you for purchasing an Electrolux appliance. You’ve chosen a product that
brings with it decades of professional experience and innovation. Ingenious and
stylish, it has been designed with you in mind. So whenever you use it, you can
be safe in the knowledge that you’ll get great results every time.
Welcome to Electrolux.
Visit our website for:
Get usage advice, brochures, trouble shooter, service information:
www.electrolux.com/webselfservice
Register your product for better service:
www.registerelectrolux.com
Buy Accessories, Consumables and Original spare parts for your appliance:
www.electrolux.com/shop
CUSTOMER CARE AND SERVICE
Always use original spare parts.
When contacting our Authorised Service Centre, ensure that you have the
following data available: Model, PNC, Serial Number.
The information can be found on the rating plate.
Warning / Caution-Safety information
General information and tips
Environmental information
Subject to change without notice.
1.
SAFETY INFORMATION
Before the installation and use of the appliance, carefully
read the supplied instructions. The manufacturer is not
responsible for any injuries or damage that are the result
of incorrect installation or usage. Always keep the
ENGLISH
3
instructions in a safe and accessible location for future
reference.
1.1 Children and vulnerable people safety
•
•
•
•
•
•
•
•
This appliance can be used by children aged from 8
years and above and persons with reduced physical,
sensory or mental capabilities or lack of experience
and knowledge if they have been given supervision or
instruction concerning the use of the appliance in a
safe way and understand the hazards involved.
Children between 3 and 8 years of age and persons
with very extensive and complex disabilities shall be
kept away from the appliance unless continuously
supervised.
Children of less than 3 years of age should be kept
away from the appliance unless continuously
supervised.
Do not let children play with the appliance.
Keep all packaging away from children and dispose of
it appropriately.
Keep children and pets away from the appliance when
it operates or when it cools down. Accessible parts
may become hot during use.
If the appliance has a child safety device, it should be
activated.
Children shall not carry out cleaning and user
maintenance of the appliance without supervision.
1.2 General Safety
•
•
•
WARNING: The appliance and its accessible parts
become hot during use. Care should be taken to avoid
touching heating elements.
WARNING: Unattended cooking on a hob with fat or
oil can be dangerous and may result in fire.
NEVER try to extinguish a fire with water, but switch
off the appliance and then cover flame e.g. with a lid
or a fire blanket.
4
www.electrolux.com
•
•
•
•
•
•
•
•
•
•
CAUTION: The appliance must not be supplied
through an external switching device, such as a timer,
or connected to a circuit that is regularly switched on
and off by a utility.
CAUTION: The cooking process has to be supervised.
A short term cooking process has to be supervised
continuously.
WARNING: Danger of fire: Do not store items on the
cooking surfaces.
Metallic objects such as knives, forks, spoons and lids
should not be placed on the hob surface since they
can get hot.
Do not use the appliance before installing it in the
built-in structure.
Do not use a steam cleaner to clean the appliance.
If the glass ceramic surface / glass surface is cracked,
switch off the appliance and unplug it from the mains.
In case the appliance is connected to the mains
directly using junction box, remove the fuse to
disconnect the appliance from power supply. In either
case contact the Authorised Service Centre.
In case of hotplate glass breakage:
– shut immediately off all burners and any electrical
heating element and isolate the appliance from the
power supply,
– do not touch the appliance surface,
– do not use the appliance.
If the supply cord is damaged, it must be replaced by
the manufacturer, an authorized Service or similarly
qualified persons in order to avoid a hazard.
Where the appliance is directly connected to the
power supply, an all-pole isolating switch with a
contact gap is required. Complete disconnection in
compliance with the conditions specified in
overvoltage category III must be guaranteed. The
earth cable is excluded from this.
ENGLISH
•
•
5
When you route the mains cable, make sure that the
cable doesn't come into direct contact (for example
using insulating sleeving) with parts that can reach
temperatures of more than 50°C above room
temperature.
WARNING: Use only hob guards designed by the
manufacturer of the cooking appliance or indicated by
the manufacturer of the appliance in the instructions
for use as suitable or hob guards incorporated in the
appliance. The use of inappropriate guards can cause
accidents.
2. SAFETY INSTRUCTIONS
This appliance is suitable for the
following markets:
BH JO KW LB QA AE
•
2.1 Installation
WARNING!
Only a qualified person must
install this appliance.
2.2 Electrical Connection
WARNING!
Risk of injury or damage to
the appliance.
•
•
•
•
•
•
•
•
•
Remove all the packaging.
Do not install or use a damaged
appliance.
Follow the installation instructions
supplied with the appliance.
Keep the minimum distance from
other appliances and units.
Always take care when moving the
appliance as it is heavy. Always use
safety gloves and enclosed footwear.
Seal the cut surfaces with a sealant to
prevent moisture to cause swelling.
Protect the bottom of the appliance
from steam and moisture.
Do not install the appliance adjacent
to a door or under a window. This
prevents hot cookware falling from the
appliance when the door or the
window is opened.
If the appliance is installed above
drawers make sure that the space,
between the bottom of the appliance
and the upper drawer, is sufficient for
air circulation.
The bottom of the appliance can get
hot. Make sure to install a noncombustible separation panel under
the appliance to prevent access to the
bottom.
WARNING!
Risk of fire and electric
shock.
•
•
•
•
•
•
•
•
All electrical connections should be
made by a qualified electrician.
The appliance must be earthed.
Before carrying out any operation
make sure that the appliance is
disconnected from the power supply.
Make sure that the parameters on the
rating plate are compatible with the
electrical ratings of the mains power
supply.
Make sure the appliance is installed
correctly. Loose and incorrect
electricity mains cable or plug (if
applicable) can make the terminal
become too hot.
Use the correct electricity mains
cable.
Do not let the electricity mains cable
tangle.
Make sure that a shock protection is
installed.
6
www.electrolux.com
•
•
•
•
•
•
•
•
•
•
Use the strain relief clamp on the
cable.
Make sure the mains cable or plug (if
applicable) does not touch the hot
appliance or hot cookware, when you
connect the appliance to the near
sockets.
Do not use multi-plug adapters and
extension cables.
Make sure not to cause damage to
the mains plug (if applicable) or to the
mains cable. Contact our Authorised
Service Centre or an electrician to
change a damaged mains cable.
The shock protection of live and
insulated parts must be fastened in
such a way that it cannot be removed
without tools.
Connect the mains plug to the mains
socket only at the end of the
installation. Make sure that there is
access to the mains plug after the
installation.
If the mains socket is loose, do not
connect the mains plug.
Do not pull the mains cable to
disconnect the appliance. Always pull
the mains plug.
Use only correct isolation devices: line
protecting cut-outs, fuses (screw type
fuses removed from the holder), earth
leakage trips and contactors.
The electrical installation must have
an isolation device which lets you
disconnect the appliance from the
mains at all poles. The isolation
device must have a contact opening
width of minimum 3 mm.
installation regulations. Follow the
requirements for adequate ventilation.
2.4 Use
WARNING!
Risk of injury, burns and
electric shock.
•
•
•
•
•
•
•
•
•
•
WARNING!
Risk of fire and explosion
•
2.3 Gas connection
•
•
•
•
•
•
•
All gas connections must be made by
a qualified person.
Before installation, make sure that the
local distribution conditions (nature of
the gas and gas pressure) and the
adjustment of the appliance are
compatible.
Make sure that there is air circulation
around the appliance.
The information about the gas supply
is on the rating plate.
This appliance is not connected to a
device, which evacuates the products
of combustion. Make sure to connect
the appliance according to current
Remove all the packaging, labelling
and protective film (if applicable)
before first use.
This appliance is for household use
only.
Do not change the specification of this
appliance.
Make sure that the ventilation
openings are not blocked.
Do not let the appliance stay
unattended during operation.
Set the cooking zone to “off” after
each use.
Do not put cutlery or saucepan lids on
the cooking zones. They can become
hot.
Do not operate the appliance with wet
hands or when it has contact with
water.
Do not use the appliance as a work
surface or as a storage surface.
When you place food into hot oil, it
may splash.
•
Fats and oil when heated can release
flammable vapours. Keep flames or
heated objects away from fats and
oils when you cook with them.
The vapours that very hot oil releases
can cause spontaneous combustion.
Used oil, that can contain food
remnants, can cause fire at a lower
temperature than oil used for the first
time.
Do not put flammable products or
items that are wet with flammable
products in, near or on the appliance.
WARNING!
Risk of damage to the
appliance.
•
•
Do not keep hot cookware on the
control panel.
Do not let cookware boil dry.
ENGLISH
•
•
•
•
•
•
•
•
•
•
•
•
•
•
Be careful not to let objects or
cookware fall on the appliance. The
surface can be damaged.
Never leave a burner on with empty
cookware or without cookware.
Do not put aluminium foil on the
appliance.
Cookware made of cast iron,
aluminium or with a damaged bottom
can cause scratches on the glass /
glass ceramic. Always lift these
objects up when you have to move
them on the cooking surface.
Use only stable cookware with the
correct shape and diameter larger
than the dimensions of the burners.
Make sure cookware is centrally
positioned on the burners.
Do not use large cookware that
overlap the edges of the appliance.
This can cause damage to the
worktop surface.
Make sure the flame does not go out
when you quickly turn the knob from
the maximum to the minimum
position.
Use only the accessories supplied
with the appliance.
Do not install a flame diffuser on the
burner.
The use of a gas cooking appliance
results in the production of heat and
moisture. Provide good ventilation in
the room where the appliance is
installed.
Prolonged intensive use of the
appliance may call for additional
ventilation, for example opening of a
window, or more effective ventilation,
for example increasing the level of
mechanical ventilation where present.
This appliance is for cooking
purposes only. It must not be used for
other purposes, for example room
heating.
Do not let acid liquids, for example
vinegar, lemon juice or limescale
remover, touch the hob. This can
cause matt patches.
3. INSTALLATION
WARNING!
Refer to Safety chapters.
•
7
Discoloration of the enamel or
stainless steel has no effect on the
performance of the appliance.
2.5 Care and cleaning
WARNING!
Do not remove the buttons,
knobs or gaskets from the
control panel. Water may get
inside the appliance and
cause damage.
•
•
•
•
•
•
Clean the appliance regularly to
prevent the deterioration of the
surface material.
Deactivate the appliance and let it
cool down before you clean it.
Disconnect the appliance from the
electrical supply before maintenance.
Do not use water spray and steam to
clean the appliance.
Clean the appliance with a moist soft
cloth. Use only neutral detergents. Do
not use abrasive products, abrasive
cleaning pads, solvents or metal
objects.
Do not clean the burners in the
dishwasher.
2.6 Service
•
•
To repair the appliance contact the
Authorised Service Centre.
Use original spare parts only.
2.7 Disposal
WARNING!
Risk of injury or suffocation.
•
•
•
•
Contact your municipal authority for
information on how to discard the
appliance correctly.
Disconnect the appliance from the
mains supply.
Cut off the mains electrical cable
close to the appliance and dispose of
it.
Flat the external gas pipes.
8
www.electrolux.com
3.1 Before the installation
C. Elbow supplied with the appliance
WARNING!
It is important to install the
elbow correctly. Make sure
that the shoulder is on the
end of the thread. Then
install it on the hob
connecting pipe. Incorrect
assembly may cause a gas
leakage.
Before you install the hob, write down the
information below from the rating plate.
The rating plate is on the bottom of the
hob.
Model .......................................
PNC .........................................
Serial number ...........................
3.2 Gas Connection
WARNING!
The following instructions
about installation,
connection and maintenance
must be carried out by
qualified personnel in
compliance with standards
and local regulations in
force.
Choose fixed connections or use a
flexible pipe in stainless steel in
compliance with the regulation in force. If
you use flexible metallic pipes, be careful
they do not come in touch with mobile
parts or they are not squeezed. Also be
careful when the hob is put together with
an oven.
Make sure that the gas
supply pressure of the
appliance obeys the
recommended values. The
adjustable connection is
fixed to the comprehensive
ramp by means of a
threaded nut G 1/2". Screw
the parts without force,
adjust the connection in the
necessary direction and
tighten everything.
Liquid gas
Use the rubber pipe holder for liquid gas.
Always engage the gasket. Then
continue with the gas connection.
The flexible pipe is prepared for apply
when:
•
it can not get hot more than room
temperature, higher than 30°C;
• it is no longer than 1500 mm;
• it shows no throttles;
• it is not subject to traction or torsion;
• it does not get in touch with cutting
edges or corners;
• it can be easily examined in order to
make sure its condition.
The control of preservation of the flexible
pipe consists in checking that:
•
it does not show cracks, cuts, marks
of burnings on the two ends and on its
full length;
• the material is not hardened, but
shows its correct elasticity;
• the fastening clamps are not rusted;
• expired term is not due.
If one or more defects are visible, do not
repair the pipe, but replace it.
WARNING!
When installation is
complete, make sure that
the seal of each pipe fitting
is correct. Use a soapy
solution, not a flame!
3.3 Injectors replacement
A
B C
A. End of shaft
B. Washer supplied with the appliance
1. Remove the pan supports.
2. Remove the caps and crowns of the
burner.
3. With a socket spanner 7 remove the
injectors and replace them with the
ones which are necessary for the
ENGLISH
type of gas you use (see table in
"Technical Data" chapter).
4. Assemble the parts, follow the same
procedure backwards.
5. Attach the label with the new type of
gas supply near the gas supply pipe.
You can find this label in the package
supplied with the appliance.
If the supply gas pressure is changeable
or different from the necessary pressure,
you must fit an applicable pressure
adjuster on the gas supply pipe.
3.4 Adjustment of minimum
level
WARNING!
Information for authorised
installer only.
To adjust the minimum level of the
burners:
9
A
5. If you change:
• from natural gas G20 20 mbar to
liquid gas, fully tighten the bypass
screw in.
• from liquid gas to natural gas G20
20 mbar, undo the bypass screw
approximately 1/4 of a turn (1/2 of
a turn for Multi Crown burner).
6. Reassemble the magnet holder and
the knob.
1. Light the burner.
2. Turn the knob on the minimum
position.
3. Remove the knob and using thin
screwdriver lift up and remove the
plastic magnet holder.
WARNING!
Make sure the flame does
not go out when you quickly
turn the knob from the
maximum position to the
minimum position.
4. With a thin screwdriver, adjust the
bypass screw position (A).
3.5 Electrical connection
•
•
Make sure that the rated voltage and
type of power on the rating plate
agree with the voltage and the power
of the local power supply.
This appliance is supplied with a
mains cable. It has to be supplied with
a correct plug which can hold the load
that the rating plate rates. Make sure
that you install the plug in a correct
socket.
10
www.electrolux.com
•
•
•
•
•
Always use a correctly installed
shockproof socket.
Make sure that there is an access to
the mains plug after the installation.
Do not pull the mains cable to
disconnect the appliance. Always pull
the mains plug.
There is a risk of fire when the
appliance is in connection with an
extension cable, an adapter or a
multiple connection. Make sure that
the ground connection agrees with the
standards and regulations.
Do not let the power cable to heat up
to a temperature higher than 90° C.
Make sure that you connect
the blue neutral cable to the
terminal with a letter "N" on
it. Connect the brown (or
black) phase cable to the
terminal which has a letter
"L". Keep the phase cable
connected at all times.
If the pilot lights turn on after
connecting the hob to the
mains, turn on and off the
control knob and wait until
the residual heat indicator
goes out.
3.7 Assembly
1.
2.
3.
3.6 Connection cable
To replace the connection cable use only
the special cable or its equivalent. The
cable type is: H03V2V2-F T90.
Make sure that the cable section is
applicable to the voltage and the working
temperature. The yellow / green earth
wire must be approximately 2 cm longer
than the brown (or black) phase wire.
min.
100 mm
min.
650 mm
min.
55 mm
30 mm
480+02 mm
4.
560+02 mm
ENGLISH
11
3.8 Installing hob under the
hood
5.
If you install the hob under a
hood, please see the
installation instructions of the
hood for the minimum
distance between the
appliances.
6.
3.9 Possibilities for insertion
A
The panel installed below the hob must
be easy to remove and let an easy
access in case a technical assistance
intervention is necessary.
Kitchen unit with door
30 mm
B
7.
A) supplied seal
B) supplied brackets
A
60 mm
min 20 mm
(max 150 mm)
B
A. Removable panel
B. Space for connections
CAUTION!
Install the appliance only on
a worktop with flat surface.
Kitchen unit with oven
The electrical connection of the hob and
the oven must be installed separately for
safety reasons and to let easy remove
oven from the unit.
12
www.electrolux.com
4. PRODUCT DESCRIPTION
4.1 Cooking surface layout
1
2
3
4
5
6
1
2
3
Semi-rapid burner
Multi Crown burner
Auxiliary burner
Control panel
Control knobs
Window for Hob²Hood infrared signal
4
5
6
4.2 Control panel layout
1
2
3
4
Use the sensor fields to operate the Minute Minder and Hob²Hood. The displays,
indicators and sounds tell which functions operate.
Sen‐
sor
field
1
2
3
4
/
Function
Comment
Hob²Hood
To activate and deactivate the manual
mode of the function.
Timer display
To show the time in minutes.
-
To increase or decrease the time.
-
To select the Timer function.
ENGLISH
4.3 Control knob
Symbol
A. Residual heat indicator.
WARNING!
There is a risk of burns from
residual heat.
Description
no gas supply / off posi‐
tion
The residual heat indicator
lights up when you turn off
the burner.
ignition position / maxi‐
mum gas supply
minimum gas supply
4.4 Residual heat
$
Knob of the burner
Time of cooking (min)
on < 5
on > 5
Multi Crown
off after 25
off after 25
Semi-rapid
off after 10
off after 20
Auxiliary
off after 5
off after 15
5. DAILY USE
WARNING!
Refer to Safety chapters.
13
14
www.electrolux.com
5.1 Burner overview
1. Push the control knob down and turn
it counterclockwise to the maximum
$
%
&
'
$
%
&
'
A.
B.
C.
D.
Burner cap
Burner crown
Ignition candle
Thermocouple
5.2 Ignition of the burner
Always light the burner
before you put on the
cookware.
WARNING!
Be very careful when you
use open fire in the kitchen
environment. The
manufacturer declines any
responsibility in case of the
flame misuse.
gas supply position ( ).
2. Keep the control knob pushed for
equal or less than 10 seconds. This
lets the thermocouple warm up. If
not, the gas supply is interrupted.
3. Adjust the flame after it is regular.
If after some tries the burner
does not light, check if the
crown and its cap are in
correct positions.
WARNING!
Do not keep the control knob
pushed for more than 15
seconds. If the burner does
not light after 15 seconds,
release the control knob,
turn it into off position and try
to light the burner again after
minimum 1 minute.
CAUTION!
In the absence of electricity
you can ignite the burner
without electrical device; in
this case approach the
burner with a flame, turn the
control knob counterclockwise to maximum gas
supply position and push it
down. Keep the control knob
pushed for equal or less
than 10 seconds to let the
thermocouple warm up.
If the burner accidentally
goes out, turn the control
knob to the off position and
try to light the burner again
after minimum 1 minute.
The spark generator can
start automatically when you
switch on the mains, after
installation or a power cut. It
is normal.
Each control knob has a pilot
light. It lights up when you
turn the control knob.
ENGLISH
You can use the Minute
Minder at any time also if the
appliance is off.
The hob is supplied with the
progressive valves. They
make the flame regulation
more precise.
The function has no effect
on the operation of the
burners.
WARNING!
If you do not switch the knob
to the off position, after two
hours a warning sound is
emitted and the symbols
flash red. It reminds you that
the burner is on. To stop the
sound, touch
,
,
5.5
or
.
5.3 Turning the burner off
For most of the hoods, the
remote system is originally
deactivated. Activate it
before you use the function.
For more information refer to
the hood user manual.
To put the flame out, turn the knob to the
off position
.
WARNING!
Always turn the flame down
or switch it off before you
remove the pans from the
burner.
Automatic modes
5.4 Minute Minder
You can use this function as a Minute
Minder.
1. Touch .
To activate the function.
or
of the timer to set the
2. Touch
time (00 - 99 minutes).
When the time comes to an end, the
sound operates and 00 flashes.
In the last minute the time
decreases in seconds, and
the last 10 seconds the timer
emits a sound signal.
3. Touch , ,
To stop the sound.
or
.
4. To stop the timer, touch longer
6. HINTS AND TIPS
WARNING!
Refer to Safety chapters.
Hob²Hood
It is an advanced automatic function
which connects the hob to a special
hood. Both the hob and the hood have
an infrared signal communicator. You
can also operate the fan from the hob
manually.
.
Mode
Automatic
light
Fan speed
H0
Off
Off
HL
On
Off
H1
On
Level 1
H2
On
Level 2
H3
On
Level 3
Touch longer
to turn off
the fan and the light.
WARNING!
After end of cooking, the
hood does not turn off
automatically. Turn it off
manually.
15
16
www.electrolux.com
6.1 Cookware
CAUTION!
Do not use cast iron pans,
clay or earthenware pots,
grill or toaster plates.
WARNING!
Do not put the same pan on
two burners.
WARNING!
Do not put unstable or
damaged pots on the burner
to prevent spills and injuries.
CAUTION!
Make sure that the bottoms
of pots do not stand too
close to the control knob,
otherwise the flame heats
the control knob up.
CAUTION!
Make sure that pot handles
are not above the front edge
of the cooktop.
Burner
Diameter of
cookware
(mm)
Multi Crown
180 - 260
Semi-rapid
120 - 220
Auxiliary
80 - 180
6.4 Hints and Tips for
Hob²Hood
When you operate the hob with the
function:
•
Protect the hood panel from direct
sunlight.
• Do not spot halogen light on the hood
panel.
• Do not cover the hob control panel.
• Do not interrupt the signal between
the hob and the hood (e.g. with the
hand, a cookware handle or a tall
pot). See the picture.
The hood in the picture is only
exemplary.
CAUTION!
Make sure that the pots are
placed centrally on the
burner in order to get the
maximum stability and a
lower gas consumption.
CAUTION!
Liquids spilt during cooking
can cause the glass to
break.
6.2 Energy saving
•
•
If it is possible, always put the lids on
the cookware.
When the liquid starts to boil, turn
down the flame to barely simmer the
liquid.
6.3 Diameters of cookware
Use cookware with
diameters applicable to the
size of burners.
Keep the window for
Hob²Hood infrared signal
communicator clean.
Other remotely controlled
appliances may block the
signal. Do not use any such
appliances near to the hob
while Hob²Hood is on.
Cooker hoods with the Hob²Hood
function
ENGLISH
To find the full range of cooker hoods
which work with this function refer to our
consumer website. The Electrolux cooker
17
hoods that work with this function must
have the symbol .
7. CARE AND CLEANING
WARNING!
Refer to Safety chapters.
7.1 General information
•
•
•
•
Clean the hob after each use.
Always use cookware with a clean
base.
Scratches or dark stains on the
surface have no effect on how the hob
operates.
Use a special cleaner suitable for the
surface of the hob.
The presence of water or
other liquids on the control
panel can accidentally
activate or deactivate the
hob functions.
WARNING!
Do not use knives, scrapers
or similar instruments to
clean the surface of the
glass or the rims of the
burners and the frame (if
applicable).
•
remove stubborn stains with a paste
cleaner.
3. After you clean the pan supports,
make sure that they are in correct
positions.
4. For the burner to operate correctly,
make sure that the arms of the pan
supports are inserted in the recesses
of the enamelled plates.
7.3 Removing and assembling
pan supports
After cleaning of the hob, make sure that
pan supports are in a correct position. In
order to place a pan support properly,
make sure that its arms fits the cut-outs
placed at the base of the burner as
shown in the picture. This way, a pan
support is stable and fixed.
Wash stainless steel parts with water,
and then dry them with a soft cloth.
7.2 Pan supports
The pan supports are not
resistant to washing in a
dishwasher. They must be
washed by hand.
7.4 Cleaning the hob
•
•
1. Remove the pan supports to easily
clean the hob.
Be very careful when
you replace the pan
supports to prevent the
hob top from damage.
2. The enamel coating occasionally can
have rough edges, so be careful
when you wash the pan supports by
hand and dry them. If necessary,
•
Remove immediately: melted plastic,
plastic foil, sugar and food with sugar,
otherwise, the dirt can cause damage
to the hob. Take care to avoid burns.
Remove when the hob is
sufficiently cool: limescale rings,
water rings, fat stains, shiny metallic
discoloration. Clean the hob with a
moist cloth and a non-abrasive
detergent. After cleaning, wipe the
hob dry with a soft cloth.
To clean the enamelled parts, caps
and crowns, wash them with warm
soapy water and dry them carefully
before you put them back on.
18
www.electrolux.com
7.5 Cleaning the spark plug
7.6 Periodic maintenance
This feature is obtained through a
ceramic ignition candle with a metal
electrode. Keep these components well
clean to prevent difficult lighting and
check that the burner crown holes are
not obstructed.
Speak to your local Authorised Service
Centre periodically to check the
conditions of the gas supply pipe and the
pressure adjuster, if fitted.
8. TROUBLESHOOTING
WARNING!
Refer to Safety chapters.
8.1 What to do if...
Problem
Possible cause
Remedy
There is no spark when
you try to activate the
spark generator.
The hob is not connected
to an electrical supply or it
is connected incorrectly.
Check if the hob is correct‐
ly connected to the electri‐
cal supply.
The fuse is blown.
Make sure that the fuse is
the cause of the malfunc‐
tion. If the fuse is blown
again and again, contact a
qualified electrician.
Burner cap and crown are
placed incorrectly.
Place the burner cap and
crown correctly.
The flame extinguishes im‐ Thermocouple is not heat‐
mediately after ignition.
ed up sufficiently.
After lightning the flame,
keep the knob pushed for
equal or less than 10 sec‐
onds.
The flame ring is uneven.
Burner crown is blocked
with food residues.
Make sure that the injector
is not blocked and the
burner crown is clean.
The control panel bright‐
ness is reduced or it
switches off.
The temperature of the
Let the hob cool down.
plate is high. To ensure
long lifetime of the display
the brightness is reduced
depending on the tempera‐
ture of the hob. Above a
certain temperature the
control panel switches off.
The control knob pilot
Pilot light test.
lights turn on after con‐
necting the hob to the
mains or after a power out‐
age.
Refer to "Installation".
ENGLISH
Problem
Possible cause
Remedy
Hob²Hood function does
not work.
You covered the control
panel.
Remove the object from
the control panel.
You cannot activate or op‐
erate Hob²Hood and Mi‐
nute Minder.
There is water or fat stains
on the control panel.
Clean the control panel.
8.2 If you cannot find a
solution...
during the warranty period. The
instructions about the Service Centre
and conditions of guarantee are in the
guarantee booklet.
If you cannot find a solution to the
problem yourself, contact your dealer or
an Authorised Service Centre. Give the
data from the rating plate. Make sure,
you operated the hob correctly. If not the
servicing by a service technician or
dealer will not be free of charge, also
A
8.3 Labels supplied with the
accessories bag
Stick the adhesive labels as indicated
below:
B
MOD.
MOD.
PROD.NO.
PROD.NO.
SER.NO
SER.NO
DATA
DATA
C
MOD.
PROD.NO.
SER.NO.
0049
TYPE
IP20
03 IT
MADE IN ITALY
A. Stick it on Guarantee Card and send
this part (if applicable).
B. Stick it on Guarantee Card and keep
this part (if applicable).
C. Stick it on instruction booklet.
9. TECHNICAL DATA
9.1 Hob dimensions
Width
590 mm
Depth
520 mm
19
20
www.electrolux.com
9.2 Bypass diameters
BURNER
Ø BYPASS 1/100 mm
Multi Crown
57
Semi-rapid
35
Auxiliary
28
9.3 Other technical data
TOTAL POW‐
ER:
Electric supply:
Gas original:
Gas replace‐
ment:
G30/G31 (3B/P) 30/30
mbar
607 g/h
G20 (2H) 20 mbar
8,9 kW
220-240 V ~ 50-60 Hz
Appliance cate‐ II2H3B/P
gory:
Gas connec‐
tion:
R 1/2"
Appliance
class:
3
9.4 Gas burners for LPG G30/G31 30/30 mbar
BURNER
NORMAL
POWER kW
MINIMUM
POWER kW
INJECTOR
MARK
NOMINAL GAS
FLOW g/h
Multi Crown
3,55
1,4
095
258
Semi-rapid
1,9
0,6
71
138
Auxiliary
1,0
0,33
50
73
9.5 Gas burners for NATURAL GAS G20 20 mbar
BURNER
NORMAL POWER MINIMUM POWER
kW
kW
INJECTOR MARK
Multi Crown
3,9
1,4
146
Semi-rapid
2,0
0,6
96x
Auxiliary
1,0
0,33
70
10. ENVIRONMENTAL CONCERNS
Recycle materials with the symbol .
Put the packaging in relevant containers
to recycle it. Help protect the
environment and human health by
recycling waste of electrical and
electronic appliances. Do not dispose of
ENGLISH
21
product to your local recycling facility or
contact your municipal office.
appliances marked with the symbol
with the household waste. Return the
*
22
www.electrolux.com
ENGLISH
23
867356380-B-282019
www.electrolux.com/shop
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising