AEG | HVB95450IB | User manual | Aeg HVB95450IB User Manual

Aeg HVB95450IB User Manual
HVB95450IB
USER
MANUAL
EN
User Manual
Hob
2
www.aeg.com
CONTENTS
1. SAFETY INFORMATION............................................................................................. 2
2. SAFETY INSTRUCTIONS.............................................................................................5
3. INSTALLATION............................................................................................................7
4. PRODUCT DESCRIPTION.........................................................................................13
5. DAILY USE.................................................................................................................. 14
6. HINTS AND TIPS........................................................................................................18
7. CARE AND CLEANING.............................................................................................20
8. TROUBLESHOOTING............................................................................................... 22
9. TECHNICAL DATA.................................................................................................... 24
FOR PERFECT RESULTS
Thank you for choosing this AEG product. We have created it to give you
impeccable performance for many years, with innovative technologies that help
make life simpler - features you might not find on ordinary appliances. Please
spend a few minutes reading to get the very best from it.
Visit our website for:
Get usage advice, brochures, trouble shooter, service information:
www.aeg.com/webselfservice
Register your product for better service:
www.registeraeg.com
Buy Accessories, Consumables and Original spare parts for your appliance:
www.aeg.com/shop
CUSTOMER CARE AND SERVICE
Always use original spare parts.
When contacting our Authorised Service Centre, ensure that you have the
following data available: Model, PNC, Serial Number.
The information can be found on the rating plate.
Warning / Caution-Safety information
General information and tips
Environmental information
Subject to change without notice.
1.
SAFETY INFORMATION
Before the installation and use of the appliance,
carefully read the supplied instructions. The
manufacturer is not responsible for any injuries or
damage that are the result of incorrect installation or
usage. Always keep the instructions in a safe and
accessible location for future reference.
ENGLISH
3
1.1 Children and vulnerable people safety
•
•
•
•
•
•
•
•
This appliance can be used by children aged from 8
years and above and persons with reduced physical,
sensory or mental capabilities or lack of experience
and knowledge if they have been given supervision or
instruction concerning the use of the appliance in a
safe way and understand the hazards involved.
Children between 3 and 8 years of age and persons
with very extensive and complex disabilities shall be
kept away from the appliance unless continuously
supervised.
Children of less than 3 years of age should be kept
away from the appliance unless continuously
supervised.
Do not let children play with the appliance.
Keep all packaging away from children and dispose of
it appropriately.
Keep children and pets away from the appliance when
it operates or when it cools down. Accessible parts
may become hot during use.
If the appliance has a child safety device, it should be
activated.
Children shall not carry out cleaning and user
maintenance of the appliance without supervision.
1.2 General Safety
•
•
•
•
WARNING: The appliance and its accessible parts
become hot during use. Care should be taken to
avoid touching heating elements.
WARNING: Unattended cooking on a hob with fat or
oil can be dangerous and may result in fire.
NEVER try to extinguish a fire with water, but switch
off the appliance and then cover flame e.g. with a lid
or a fire blanket.
CAUTION: The appliance must not be supplied
through an external switching device, such as a timer,
4
www.aeg.com
•
•
•
•
•
•
•
•
•
•
or connected to a circuit that is regularly switched on
and off by a utility.
CAUTION: The cooking process has to be supervised.
A short term cooking process has to be supervised
continuously.
WARNING: Danger of fire: Do not store items on the
cooking surfaces.
Metallic objects such as knives, forks, spoons and lids
should not be placed on the hob surface since they
can get hot.
Do not use the appliance before installing it in the
built-in structure.
Do not use a steam cleaner to clean the appliance.
If the glass ceramic surface / glass surface is cracked,
switch off the appliance and unplug it from the mains.
In case the appliance is connected to the mains
directly using junction box, remove the fuse to
disconnect the appliance from power supply. In either
case contact the Authorised Service Centre.
In case of hotplate glass breakage:
– shut immediately off all burners and any electrical
heating element and isolate the appliance from the
power supply,
– do not touch the appliance surface,
– do not use the appliance.
If the supply cord is damaged, it must be replaced by
the manufacturer, an authorized Service or similarly
qualified persons in order to avoid a hazard.
Where the appliance is directly connected to the
power supply, an all-pole isolating switch with a
contact gap is required. Complete disconnection in
compliance with the conditions specified in
overvoltage category III must be guaranteed. The
earth cable is excluded from this.
When you route the mains cable, make sure that the
cable doesn't come into direct contact (for example
using insulating sleeving) with parts that can reach
ENGLISH
•
5
temperatures of more than 50°C above room
temperature.
WARNING: Use only hob guards designed by the
manufacturer of the cooking appliance or indicated by
the manufacturer of the appliance in the instructions
for use as suitable or hob guards incorporated in the
appliance. The use of inappropriate guards can cause
accidents.
2. SAFETY INSTRUCTIONS
This appliance is suitable for the
following markets: MT
2.1 Installation
WARNING!
Only a qualified person must
install this appliance.
WARNING!
Risk of injury or damage to
the appliance.
• Remove all the packaging.
• Do not install or use a damaged
appliance.
• Follow the installation instructions
supplied with the appliance.
• Keep the minimum distance from
other appliances and units.
• Always take care when moving the
appliance as it is heavy. Always use
safety gloves and enclosed footwear.
• Seal the cut surfaces with a sealant to
prevent moisture to cause swelling.
• Protect the bottom of the appliance
from steam and moisture.
• Do not install the appliance adjacent
to a door or under a window. This
prevents hot cookware falling from
the appliance when the door or the
window is opened.
• If the appliance is installed above
drawers make sure that the space,
between the bottom of the appliance
and the upper drawer, is sufficient for
air circulation.
• The bottom of the appliance can get
hot. Make sure to install a noncombustible separation panel under
the appliance to prevent access to the
bottom.
2.2 Electrical Connection
WARNING!
Risk of fire and electric
shock.
• All electrical connections should be
made by a qualified electrician.
• The appliance must be earthed.
• Before carrying out any operation
make sure that the appliance is
disconnected from the power supply.
• Make sure that the parameters on the
rating plate are compatible with the
electrical ratings of the mains power
supply.
• Make sure the appliance is installed
correctly. Loose and incorrect
electricity mains cable or plug (if
applicable) can make the terminal
become too hot.
• Use the correct electricity mains
cable.
• Do not let the electricity mains cable
tangle.
• Make sure that a shock protection is
installed.
• Use the strain relief clamp on the
cable.
• Make sure the mains cable or plug (if
applicable) does not touch the hot
appliance or hot cookware, when you
connect the appliance to the near
sockets.
• Do not use multi-plug adapters and
extension cables.
• Make sure not to cause damage to
the mains plug (if applicable) or to the
6
www.aeg.com
•
•
•
•
•
•
mains cable. Contact our Authorised
Service Centre or an electrician to
change a damaged mains cable.
The shock protection of live and
insulated parts must be fastened in
such a way that it cannot be removed
without tools.
Connect the mains plug to the mains
socket only at the end of the
installation. Make sure that there is
access to the mains plug after the
installation.
If the mains socket is loose, do not
connect the mains plug.
Do not pull the mains cable to
disconnect the appliance. Always pull
the mains plug.
Use only correct isolation devices: line
protecting cut-outs, fuses (screw type
fuses removed from the holder), earth
leakage trips and contactors.
The electrical installation must have
an isolation device which lets you
disconnect the appliance from the
mains at all poles. The isolation
device must have a contact opening
width of minimum 3 mm.
2.3 Gas connection
WARNING!
These instructions are only
valid if the country symbol
appears on the appliance. If
the symbol does not appear
on the appliance, it is
necessary to refer to the
technical instructions which
will provide the necessary
instructions concerning
modification of the
appliance to the conditions
of use of the country.
• All gas connections must be made by
a qualified person.
• Before installation, make sure that the
local distribution conditions (nature of
the gas and gas pressure) and the
adjustment of the appliance are
compatible.
• Make sure that there is air circulation
around the appliance.
• The information about the gas supply
is on the rating plate.
• This appliance is not connected to a
device, which evacuates the products
of combustion. Make sure to connect
the appliance according to current
installation regulations. Follow the
requirements for adequate
ventilation.
2.4 Use
WARNING!
Risk of injury, burns and
electric shock.
• Remove all the packaging, labelling
and protective film (if applicable)
before first use.
• This appliance is for household use
only.
• Do not change the specification of
this appliance.
• Make sure that the ventilation
openings are not blocked.
• Do not let the appliance stay
unattended during operation.
• Set the cooking zone to “off” after
each use.
• Do not put cutlery or saucepan lids on
the cooking zones. They can become
hot.
• Do not operate the appliance with
wet hands or when it has contact with
water.
• Do not use the appliance as a work
surface or as a storage surface.
• When you place food into hot oil, it
may splash.
WARNING!
Risk of fire and explosion
• Fats and oil when heated can release
flammable vapours. Keep flames or
heated objects away from fats and oils
when you cook with them.
• The vapours that very hot oil releases
can cause spontaneous combustion.
• Used oil, that can contain food
remnants, can cause fire at a lower
temperature than oil used for the first
time.
• Do not put flammable products or
items that are wet with flammable
products in, near or on the appliance.
ENGLISH
WARNING!
Risk of damage to the
appliance.
• Do not keep hot cookware on the
control panel.
• Do not let cookware boil dry.
• Be careful not to let objects or
cookware fall on the appliance. The
surface can be damaged.
• Never leave a burner on with empty
cookware or without cookware.
• Do not put aluminium foil on the
appliance.
• Cookware made of cast iron,
aluminium or with a damaged bottom
can cause scratches on the glass /
glass ceramic. Always lift these
objects up when you have to move
them on the cooking surface.
• Use only stable cookware with the
correct shape and diameter larger
than the dimensions of the burners.
• Make sure cookware is centrally
positioned on the burners.
• Do not use large cookware that
overlap the edges of the appliance.
This can cause damage to the
worktop surface.
• Use only the accessories supplied
with the appliance.
• Do not install a flame diffuser on the
burner.
• The use of a gas cooking appliance
results in the production of heat and
moisture. Provide good ventilation in
the room where the appliance is
installed.
• Prolonged intensive use of the
appliance may call for additional
ventilation, for example opening of a
window, or more effective ventilation,
for example increasing the level of
mechanical ventilation where present.
• This appliance is for cooking
purposes only. It must not be used for
other purposes, for example room
heating.
• Do not let acid liquids, for example
vinegar, lemon juice or limescale
remover, touch the hob. This can
cause matt patches.
• Discoloration of the enamel or
stainless steel has no effect on the
performance of the appliance.
2.5 Care and cleaning
• Clean the appliance regularly to
prevent the deterioration of the
surface material.
• Deactivate the appliance and let it
cool down before you clean it.
• Disconnect the appliance from the
electrical supply before maintenance.
• Do not use water spray and steam to
clean the appliance.
• Clean the appliance with a moist soft
cloth. Only use neutral detergents. Do
not use any abrasive products,
abrasive cleaning pads, solvents or
metal objects.
• Do not clean the burners in the
dishwasher.
• Clean the metal part of the flame
safety device regularly.
2.6 Disposal
WARNING!
Risk of injury or suffocation.
• Contact your municipal authority for
information on how to discard the
appliance correctly.
• Disconnect the appliance from the
mains supply.
• Cut off the mains electrical cable
close to the appliance and dispose of
it.
• Flat the external gas pipes.
2.7 Service
• To repair the appliance contact the
Authorised Service Centre.
• Use original spare parts only.
3. INSTALLATION
WARNING!
Refer to Safety chapters.
7
3.1 Before the installation
Before you install the hob, write down
the information below from the rating
8
www.aeg.com
plate. The rating plate is on the bottom
of the hob.
Model .......................................
PNC .........................................
Serial number ...........................
3.2 Important safety
requirements
This hob must be installed in accordance
with the Gas Safety (Installation and Use)
Regulations (Current Edition) and the IEE
Wiring Regulations (Current Edition).
Provision for ventilation
The hob should not be installed in a bed
sitting room with a volume of less than
20 m³. If it is installed in a room of
volume less than 5 m³ an air vent of
effective area of 100 cm² is required. If it
is installed in a room of volume between
5 m³ and 10 m³ an air vent of effective
area of 50 cm² is required, while if the
volume exceeds 11 m³ no air vent is
required.
However, if the room has a door which
opens directly to the outside no air vent
is required even if the volume is between
5 m³ and 11 m³.
Location
The hob may be located in a kitchen, a
kitchen/diner or bed sitting room (with a
volume greater than 20 m³), but not in a
bathroom or shower room.
The minimum distance combustible
material can be fitted above the hob in
line with the edges of the hob is 400 mm.
If it is fitted below 400 mm a space of 50
mm must be allowed from the edges of
the hob.
3.3 Gas Connection
WARNING!
Any gas installation must be
carried out by a GAS SAFE
REGISTER installer.
Please refer to the technical
instructions on how to adjust
the hob to the gas
specifications on Malta.
This appliance is certified for
Malta.
Make sure that, once the hob is installed,
it is easily accessible for the engineer in
the event of a breakdown.
The manufacturer will not accept liability,
should the above instructions or any of
the other safety instructions incorporated
in this instruction booklet be ignored.
On the end of the shaft, which includes
the R 1/2" threaded elbow, adjustment is
fixed so that the washer is fitted between
the components as shown in the
diagram. Screw the parts together
without using excessive force.
A
A. End of shaft with nut
Connection to the gas supply should be
with either rigid or semi-rigid pipe, i.e.
steel or copper.
The connection should be suitable for
connecting to R 1/2 (1/2 BSP male
thread).
When the final connection has been
made, it is essential that a thorough leak
test is carried out on the hob and
installation.
Make sure that the main connection pipe
does not exert any strain on the hob.
If you use flexible metal pipes make sure
that they agree to ISO 10380 and ISO
10807 standards. Be careful they do not
come in touch with mobile parts or they
are not squeezed. Also be careful when
the hob is put together with an oven.
CAUTION!
It is important to install the
elbow correctly, with the
shoulder on the end of the
thread, fitted to the hob
connecting pipe.
ENGLISH
2. Within 7 seconds, touch
seconds.
CAUTION!
Failure to ensure the correct
assembly will cause leakage
of gas.
for 3
3. Touch
3 times.
The display shows G1 mode.
4. Touch .
To enter the mode.
5. Timer display shows selected gas
type.
CAUTION!
Make sure that the gas
supply pressure of the
appliance obeys the
recommended values.
Rigid connection:
Carry out connection by using metal rigid
pipes (copper with mechanical end).
3.4 Gas selection
1. Touch
9
6. Touch
to set the gas type
according to table below.
7. Touch .
To confirm the gas type.
Touch
to exit the mode or wait for
Automatic Switch Off function activates.
for 3 seconds.
Gas selection
0
1
Liquid gas G30/G31
30/30 mbar
2
Safety risk, do not use 1 or 2 gas Safety risk, do not use 1 or 2 gas
selections. Use only 0 gas selec- selections. Use only 0 gas selection depends on gas supply.
tion depends on gas supply.
3.5 Adjustment of minimum
level
WARNING!
Information for authorised
installer only.
Switch off the hob before
the adjustment.
To increase or decrease the value and
adjust the minimum level.
7. Wait 5 seconds.
To send the selected value to power
board.
8. Check it the minimum level is correct
and touch .
To confirm the minimum level.
If the minimum level is
incorrect, repeat the steps 6
and 7.
To adjust the minimum level of the
burners:
1. Touch
for 3 seconds.
2. Within 7 seconds, touch
seconds.
for 3
4 times.
3. Touch
The display shows G2 mode.
4. Touch .
To enter the mode.
5. Wait 5 seconds, after selecting the
mode.
The burner shows minimum level and the
.
control bar shows
6. Touch
or
.
9. Touch
to select the next burner
and repeat the steps 5-8.
Touch
to exit the mode.
WARNING!
Make sure the flame does
not go out when you move
quickly from the maximum
to the minimum heat setting
position.
WARNING!
Do not set the G3 and G4
modes. It is for authorised
installer only.
10
www.aeg.com
3.6 Electrical connection
• Do not pull the mains cable to
disconnect the appliance. Always pull
the mains plug (if applicable).
• The appliance must not be connected
with an extension cable, an adapter or
a multiple socket. There is a risk of
fire.
• Do not let the power cable to heat up
to a temperature of more than 90° C.
The cable should be guided by means
of clamps fixed to the side of the
cabinet, in order to avoid any contact
with the appliance beneath the
cooktop.
• Make sure that there is access to the
mains plug after the installation.
Electrical Requirements
Permanent electrical installation must
agree with the latest I.E.E. Regulations
and local Electricity Board regulations.
For your own safety the installation must
be done by a qualified electrician (e.g.
your local Electricity Board, or a
contractor who is on the roll of the
National Inspection Council for Electrical
Installation Contracting [NICEIC]).
The manufacturer refuses
to be held responsible, if
these safety measures are
not abided by.
Supply connections
This hob has to be connected to 220-240
V (~ 50-60 Hz ) electricity supply.
The appliance is supplied with a 3 core
flexible power cable.
The wires in the cord are coloured as
follows:
Green and yellow
- Earth
Blue
- Neutral
Brown
- Live
WARNING!
A cut off plug inserted into a
13 amp socket is a serious
shock hazard. Ensure that
the cut off plug is disposed
of safely.
3.7 Connection cable
To replace the connection cable use only
the special cable or its equivalent. The
cable type is: H05SS-F T180.
Make sure that the cable section is
applicable to the voltage and the
working temperature. The yellow / green
earth wire must be approximately 2 cm
longer than the brown (or black) phase
wire.
3.8 Assembly
1.
The hob has a terminal block which is
marked as follows:
• L — Live terminal
• N — Neutral terminal
or E — Earth terminal
•
Before carrying out the connection,
make sure:
1. The limiter valve and the electrical
system can take the appliance load
(see the rating plate)
2. The supply system is equipped with
an efficient earth connection in
compliance with the current
standards and regulations
3. The outlet or omnipolar switch used
for connection is easily accessible
with the appliance installed.
min.
650mm
min.
100mm
ENGLISH
5.
2.
890
6.
3.
min. 2 mm
A
min.
38 mm
min.
2 mm
B
< 20 mm
min. 500 mm
A
12 mm
28 mm
38 mm
min
30 mm
B
57 mm
41 mm
31 mm
7.
4.
min. 2 mm
A
B
> 20 mm
min. 500 mm
A
12 mm
28 mm
38 mm
B
57 mm
41 mm
31 mm
min.
12 mm
min.
2 mm
11
12
www.aeg.com
3.10 Possibilities for insertion
8.
The panel installed below the hob must
be easy to remove and let an easy access
in case a technical assistance
intervention is necessary.
Kitchen unit with door
9.
min 6 mm
A
min 40 mm
10.
B
min 5 mm
(max 150 mm)
60 mm
A. Removable panel
B. Space for connections
CAUTION!
Install the appliance only on
a worktop with flat surface.
3.9 Installing hob under the
hood
If you install the hob under a
hood, please see the
installation instructions of
the hood for the minimum
distance between the
appliances.
Kitchen unit with oven
The electrical connection of the hob and
the oven must be installed separately for
safety reasons and to let easy remove
oven from the unit.
ENGLISH
13
4. PRODUCT DESCRIPTION
4.1 Cooking surface layout
1
1
2
1
1
2
3
4
Semi-rapid burner
Multi Crown burner
Auxiliary burner
Control panel
3
4
4.2 Control panel layout
1
2
3
4
5
11
6
9
10
8
7
Use the sensor fields to operate the appliance. The displays, indicators and sounds tell
which functions operate.
Sensor Function
field
Comment
1
ON / OFF
To activate and deactivate the hob.
2
Lock / Child Safety Device To lock / unlock the control panel.
3
Pause
To activate and deactivate the function.
4
-
Heat setting display
To show the heat setting.
5
-
Timer display
To show the time in minutes.
Led indicator
To show activated function.
Hob²Hood
To activate and deactivate the manual mode
of the function.
-
To activate and deactivate the Timer.
6
7
8
14
www.aeg.com
Sensor Function
field
-
To increase or decrease the time.
-
Area for Hob²Hood infrared signal
To hood communication.
-
Control bar
To set the heat setting for the burner.
/
9
10
11
Comment
4.3 Heat setting displays
Display
Description
Burner is deactivated.
Burner operates.
-
There is a fault.
A cooking zone is still hot (residual heat).
Lock / Child Safety Device operates.
Pause operates.
Automatic Switch Off function operates.
4.4 Hot Surface Indicator
WARNING!
If the cooking zone becomes
hot during cooking, the
setting indicator shows a
Hot Surface warning
when the zone is turned off.
The Hot Surface Indicator
shows until the cooking zone
cools.
5. DAILY USE
WARNING!
Refer to Safety chapters.
ENGLISH
5.1 Burner overview
15
After 20 seconds of non-use, the hob
deactivates.
2. After light animation, when you see
$
%
&
'
$
%
on display, touch the control bar
at the correct heat setting or move
your finger along the control bar until
you reach the correct heat setting.
To set or change the heat setting.
If after some tries the burner
does not light, check if the
crown and its cap are in
correct positions and clean
the metal part of the flame
safety device (Refer to "Care
and cleaning") .
If the burner accidentally
goes out, the hob re-ignite
the burner 3 times. If the
flame still does not light,
appears.
If the
appears, deactivate
and activate the hob.
After light animation, when
&
reappears, touch
and
within 3 seconds.
then
'
When you see
reset.
the fault is
5.3 Turning the burner off
A.
B.
C.
D.
Burner cap
Burner crown
Ignition candle
Flame safety device
5.2 Ignition of the burner
Always light the burner
before you put on the
cookware.
WARNING!
Be very careful when you use
open fire in the kitchen
environment. The
manufacturer declines any
responsibility in case of the
flame misuse.
1. Touch
hob.
for 1 second to activate the
To put the flame out, touch the control
bar to the off position
.
WARNING!
Always turn the flame down
or switch it off before you
remove the pans from the
burner.
5.4 Automatic Switch Off
The function deactivates the hob
automatically if:
• all burners are deactivated,
• you do not set the heat setting after
you activate the hob,
• you spill something or put something
on the control panel for more than 10
seconds (a pan, a cloth, etc.). An
acoustic signal sounds and the hob
16
www.aeg.com
deactivates. Remove the object or
clean the control panel.
• you do not deactivate a burner or
change the heat setting. After some
time
comes on and the hob
deactivates.
The relation between the heat setting
and the time after which the hob
deactivates:
2. Touch
for 3 seconds.
3.
appears on the display of the
burner.
4. Set the heat setting.
5. After end of the cooking process and
after turning off the cooktop, the
Lock function is active.
To completely unlock:
1. Touch
Level
Time (hours)
1
6
2
3
3
3
4
1,5
5
1,5
5.5 Lock or unlock the cooktop
You can lock the control panel while
burners operate. It prevents an
accidental change of the heat setting.
To lock the control panel:
1. Set the heat setting.
2. Touch the
3.
.
appears on the display of the
burner.
To unlock the control panel, touch
again.
You can turn the burners off
while the control panel is
locked. Use
the hob.
to deactivate
To set the lock for child safety:
1. Touch
to turn the cooktop on.
2. Touch
for 3 seconds, to activate
the lock.
bars.
3. Touch
comes on in all control
to turn the cooktop off.
You can unlock the cooktop
while the child safety
operates.
To temporarily unlock:
1. Touch
to turn the cooktop on.
to turn the cooktop on.
for 3 seconds. The lock
2. Touch
deactivates.
3. Touch
to turn the cooktop off.
5.6 Pause
This function sets all burners that operate
to the lowest heat setting.
When the function operates, you can not
change the heat setting.
When the function does not stop the
timer functions.
Touch
to activate the function.
comes on.
To deactivate the function, touch
previous heat setting comes on.
. The
5.7 Minute Minder
You can use this function as a Minute
Minder when the hob is activated.
1. Touch
.
or
of the timer to set
2. Touch
the time in minutes (00-99). The timer
indicator
starts to flash quickly
during the time setting.
starts to
3. When the timer indicator
flash slowly, the timer is activated.
When the time comes to an end, the
sound operates and 00 flashes.
4. Touch .
To stop the sound.
The function has no effect
on the operation of the
burners.
ENGLISH
The maximum duration of
the timer functions is 00-99
minutes. Check the minute
minder instructions (missing
timer adjustment).
5.8 OffSound Control
(Deactivating and activating
the sounds)
Deactivate the hob. Touch
for 3
seconds. The display comes on and goes
out. Touch
for 3 seconds.
or
comes on. Touch
of the timer to
choose one of the following:
•
- the sounds are off
- the sounds are on
•
To confirm your selection wait until the
hob deactivates automatically.
When the function is set to
hear the sounds only when:
•
•
•
•
you can
you touch
Minute Minder comes down
Count Down Timer comes down
you put something on the control
panel.
5.9
Hob²Hood
It is an advanced automatic function
which connects the hob to a special
hood. Both the hob and the hood have
an infrared signal communicator. Speed
of the fan is defined automatically on the
basis of the mode setting and
temperature of the hottest cookware on
the hob. You can also operate the fan
from the hob manually.
The hood operates only
when the hob is activated.
For most of the hoods, the
remote system is originally
deactivated. Activate it
before you use the function.
For more information refer
to the hood user manual.
17
The hob automatically sets
the speed of the fan
according to the cooking
process.
Automatic modes
Mode
Mode description
Automatic
light
Automatic
fan
speed
H0
Manual
Off
Off
H1
Auto light
On
Off
H2
Fixed speed On
1
H3
Auto speed
Low
On
0-1
H4
Auto speed
Mid
On
0-1
H5
Auto speed
High
On
0-2
H6
Auto speed
Intense
On
0-3
Changing the automatic mode
1. Deactivate the appliance.
2. Touch
for 3 seconds. the display
comes on and goes off.
3. Touch
for 3 seconds.
4. Touch
on.
a few times until
comes
of the Timer to select an
5. Touch
automatic mode.
Touch
to set the speed
manually.
Touch longer
to turn off
the fan and the light.
WARNING!
After end of cooking, the
hood does not turn off
automatically. Turn it off
manually.
18
www.aeg.com
6. HINTS AND TIPS
WARNING!
Refer to Safety chapters.
Burner
Diameter of
cookware (mm)
Multi Crown
220 - 260
CAUTION!
Do not use cast iron pans,
clay or earthenware pots,
grill or toaster plates.
Semi-rapid (rear left)
120 - 240
Semi-rapid (rear right)
120 - 240
Semi-rapid (front left)
120 - 220
WARNING!
Do not put the same pan on
two burners.
Auxiliary
80 - 180
6.1 Cookware
WARNING!
Do not put unstable or
damaged pots on the burner
to prevent spills and injuries.
CAUTION!
Make sure that pot handles
are not above the front edge
of the cooktop.
CAUTION!
Make sure that the pots are
placed centrally on the
burner in order to get the
maximum stability and a
lower gas consumption.
6.4 Hints and Tips for
Hob²Hood
When you operate the hob with the
function:
• Protect the hood panel from direct
sunlight.
• Do not spot halogen light on the
hood panel.
• Do not cover the hob control panel.
• Do not interrupt the signal between
the hob and the hood (e.g. with the
hand, a cookware handle or a tall
pot). See the picture.
The hood in the picture is only
exemplary.
CAUTION!
Liquids spilt during cooking
can cause the glass to break.
6.2 Energy saving
• If it is possible, always put the lids on
the cookware.
• When the liquid starts to boil, turn
down the flame to barely simmer the
liquid.
6.3 Diameters of cookware
Use cookware with
diameters applicable to the
size of burners.
Keep the window for
Hob²Hood infrared signal
communicator clean.
ENGLISH
Other remotely controlled
appliances may block the
signal. Do not use any such
appliances near to the hob
while Hob²Hood is on.
Cooker hoods with the Hob²Hood
function
To find the full range of cooker hoods
which work with this function refer to our
consumer website. The AEG cooker
hoods that work with this function must
have the symbol .
• For an even heat distribution use
coated pan and cook on auxiliary or
semi-rapid burners.
• Each example in the table below
shows two or three steps.
• If you use a pan, heat up the oil first,
while frying keep the pan at a
constant temperature in accordance
with the values suggested in the
table.
Cooking method symbols used in the
table:
Heat up the oil
6.5 Examples of cooking
applications
Gentle frying
The data in the table shows examples of
the heat setting and cooking times for
gentle and heavy frying, and delicate
cooking.
Heat to boiling
• Adjust the settings depend on the
type of food, the type of the gas
used, the material and the size of the
pans. Refer to diameters of cookware
in Hints and Tips chapter.
• For delicate cooking use the auxiliary
burner or semi-rapid burner with
flame spreader.
P
or
BurnFood ti
er
o
ns
Simmering
Blending, melting ingredients
Step 1
Symbol
Step 2
Le
ve
l
Time
(min)
19
Symbol
Step 3
Le
ve
l
Time
(min)
Crepe
s
4
SR
5
1-4
2
4-8
Burgers
2
AUX
5
1-5
3
4-8
Burgers
3
SR
5
1-5
3
4-8
Burgers
4
MC
5
1-5
3
4-7
Fries
4
MC
5
20-30
Symbol
Le
ve
l
Time
(min)
20
www.aeg.com
Becha-
4
AUX
2)
mel1)
Rice
porridg
4
AUX
1
5-10
5
10-20
2)
e1)
5
5-10
2)
1
4-8
2)
1
30-40
2)
1) Stirring continuously
2) Without lid
7. CARE AND CLEANING
WARNING!
Refer to Safety chapters.
7.1 General information
• Clean the hob after each use.
• It is recommended to activate the
lock / child safety device function
(Refer to "Lock or unlock the
cooktop" in "Daily use" chapter).
• Always use cookware with a clean
base.
• Scratches or dark stains on the surface
have no effect on how the hob
operates.
• Use a special cleaner suitable for the
surface of the hob.
The presence of water or
other liquids on the control
panel can accidentally
activate or deactivate the
hob functions.
WARNING!
Do not use knives, scrapers
or similar instruments to
clean the surface of the glass
or the rims of the burners
and the frame (if applicable).
• Wash stainless steel parts with water,
and then dry them with a soft cloth.
7.2 Pan supports
The pan supports are not
resistant to washing in a
dishwasher. They must be
washed by hand.
1. Remove the pan supports to easily
clean the hob.
Be very careful when you
replace the pan supports
to prevent the hob top
from damage.
2. The enamel coating occasionally can
have rough edges, so be careful
when you wash the pan supports by
hand and dry them. If necessary,
remove stubborn stains with a paste
cleaner.
3. After you clean the pan supports,
make sure that they are in correct
positions.
4. For the burner to operate correctly,
make sure that the arms of the pan
supports are aligned with the centre
of the burner.
ENGLISH
21
The shape of pan supports and the
amount of burners can be different in
other models of the appliance.
7.3 Removing pan supports
To keep the pan supports in the correct
position, they are put on metal pins
installed in the rear side of the hob. For
easier cleaning, pan supports can be
removed from the hob. Lift up the pan
supports keeping them in horizontal
position as shown in the graphic.
Do not lift the pan supports
at an angle, as this will put
strain on the metal pins. This
can cause damage to the
pins and cause them to
break.
7.4 Cleaning the hob
• Remove immediately: melted plastic,
plastic foil, sugar and food with sugar,
otherwise, the dirt can cause damage
to the hob. Take care to avoid burns.
• Remove when the hob is sufficiently
cool: limescale rings, water rings, fat
stains, shiny metallic discoloration.
Clean the hob with a moist cloth and
a non-abrasive detergent. After
cleaning, wipe the hob dry with a soft
cloth.
• To clean the enamelled parts, caps
and crowns, wash them with warm
soapy water and dry them carefully
before you put them back on.
7.5 Cleaning the ignition
candle and the flame safety
device
Keep the metal part of the ignition
candle and the flame safety device
cleaned with a moist cloth or sponge to
prevent difficult lightning or difficult
flame recognition. Check if the burner
crown is not blocked with food residues.
7.6 Periodic maintenance
Speak to your local Authorised Service
Centre periodically to check the
conditions of the gas supply pipe and
the pressure adjuster, if fitted.
22
www.aeg.com
8. TROUBLESHOOTING
WARNING!
Refer to Safety chapters.
8.1 What to do if...
Problem
Possible cause
You cannot activate or oper- The hob is not connected to
ate the hob.
an electrical supply or it is
connected incorrectly.
Remedy
Check if the hob is correctly
connected to the electrical
supply. Refer to the connection diagram.
The fuse is blown.
Make sure that the fuse is
the cause of the malfunction.
If the fuse is blown again
and again, contact a qualified electrician.
You do not set the heat setting for 20 seconds.
Activate the hob again and
set the heat setting in less
than 20 seconds.
You touched 2 or more sensor fields at the same time.
Touch only one sensor field.
There is water or fat stains
on the control panel.
Clean the control panel.
An acoustic signal sounds
You put something on one
and the hob deactivates.
or more sensor fields.
An acoustic signal sounds
when the hob is deactivated.
Remove the object from the
sensor fields.
The hob deactivates.
Remove the object from the
sensor field.
You put something on the
sensor field
.
Hob²Hood function does not You covered the control
work.
panel.
Remove the object from the
control panel.
The sensor fields become
hot.
The cookware is too large or Put large cookware on the
you put it too near to the
rear burners if possible.
controls.
There is no sound when you
touch the panel sensor
fields.
The sounds are deactivated.
Activate the sounds. Refer to
"Daily use".
comes on.
Automatic Switch Off operates.
Deactivate the hob and activate it again.
comes on.
The Child Safety Device
function operates.
Refer to "Daily use".
ENGLISH
Problem
comes on.
23
Possible cause
Remedy
There is a fault.
To reset the fault, deactivate
and activate the hob, after
light animation, when
appears, touch
re-
and then
within 3 seconds.
the fault is
When you see
reset.
Make sure that the crown
and the flame cap are correctly positioned, and clean
the metal part of the flame
safety device.
You can hear a constant
beep noise.
The electrical connection is
incorrect.
Disconnect the hob from the
electrical supply. Ask a qualified electrician to check the
installation.
comes on.
The hob is too hot.
Wait a few minutes for cool
down the hob. If possible,
put the large cookware on
the rear burners.
comes on.
There is a fault.
Follow the same procedure
as if
comes on.
Too many attempts to clear.
appeared.
Wait for 15 minutes and follow the same procedure as if
appeared.
and the number come
There is an error in the hob.
on.
Disconnect the hob from the
electrical supply for some
time. Disconnect the fuse
from the electrical system of
the house. Connect it again.
If
comes on again, speak
to an Authorised Service
Centre.
comes on.
There is a dirt around burner Refer to "Care and cleanarea.
ing".
8.2 If you cannot find a
solution...
If you cannot find a solution to the
problem yourself, contact your dealer or
an Authorised Service Centre. Give the
data from the rating plate. Make sure,
you operated the hob correctly. If not the
servicing by a service technician or
dealer will not be free of charge, also
during the warranty period. The
instructions about the Service Centre and
conditions of guarantee are in the
guarantee booklet.
24
www.aeg.com
8.3 Labels supplied with the
accessories bag
Stick the adhesive labels as indicated
below:
A
B
MOD.
MOD.
PROD.NO.
PROD.NO.
SER.NO
SER.NO
DATA
DATA
C
MOD.
PROD.NO.
SER.NO.
0049
TYPE
IP20
03 IT
MADE IN ITALY
A. Stick it on Guarantee Card and send
this part (if applicable).
B. Stick it on Guarantee Card and keep
this part (if applicable).
C. Stick it on instruction booklet.
9. TECHNICAL DATA
9.1 Hob dimensions
Width
890 mm
Depth
510 mm
9.2 Other technical data
TOTAL POWER:
Gas replacement:
Electric supply:
220-240 V ~ 50-60 Hz
Appliance cate- I3B/P
gory:
Gas connection:
R 1/2"
Appliance
class:
3
G30/G31 (3B/P) 30/30 mbar
749 g/h
ENGLISH
25
WARNING!
This appliance does not
function with the existing
gas settings if installed in
Malta. Therefore, before
connecting the appliance it
is essential to change the
nozzles according to the
type of gas used according
to the table below.
9.3 Gas burners for LPG G30/G31 30/30 mbar
BURNER
NORMAL
POWER kW
MINIMUM
POWER kW
INJECTOR
MARK
NOMINAL GAS
FLOW g/h
Multi Crown
3,6
1,8
095
262
Semi-rapid
1,9
0,75
71
138
Auxiliary
1,0
0,47
50
73
Data in the table is specified
for Malta.
10. ENVIRONMENTAL CONCERNS
Recycle materials with the symbol .
Put the packaging in relevant containers
to recycle it. Help protect the
environment and human health by
recycling waste of electrical and
electronic appliances. Do not dispose of
*
appliances marked with the symbol
with the household waste. Return the
product to your local recycling facility or
contact your municipal office.
26
www.aeg.com
ENGLISH
27
867356422-B-282019
www.aeg.com/shop
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising