Canon | EOS 5D Mark IV | User manual | Canon EOS 5D Mark IV User manual

Canon EOS 5D Mark IV User manual
EOS 5D Mark IV (WG)
Wi-Fi (Wireless Communication) Function
Instruction Manual
ENGLISH
INSTRUCTION
MANUAL
Introduction
What You Can Do Using the Wi-Fi (Wireless Communication) Functions
(1) Communicate with
a smartphone
(CANON iMAGE
GATEWAY)
(2) Save images to
Canon Connect
Station
(6) Send images to
a Web service
(3) Operate remotely
using EOS Utility
(5) Transfer images to
an FTP server
(4) Print images using
a Wi-Fi printer
2
Introduction
(1) q Communicate with a smartphone (p.29, 59, 83)
Connect the camera to a smartphone or tablet wirelessly and use
the dedicated application “Camera Connect” to operate the camera
remotely or view images stored in the camera.
In this manual and on the camera’s LCD monitor, “smartphone”
refers to smartphones and tablets.
NFC*-enabled smartphones can be connected by touching them to
the camera.
* Near Field Communication
(2) Save images to Connect Station (p.39)
Hold the camera close to Connect Station (sold separately) to
connect to and save images to it.
(3) D Operate remotely using EOS Utility (p.43, 59, 99)
Connect the camera to a computer wirelessly and operate the
camera remotely using EOS Utility (EOS software).
(4) l Print images using a Wi-Fi printer (p.49, 59, 103)
Wirelessly connect the camera to a printer supporting PictBridge
(Wireless LAN) to print images.
(5) Transfer images to an FTP server (p.75, 113)
Wirelessly connect the camera to an FTP server to transfer captured
images.
(6) w Send images to a Web service (p.129)
Share images with your family and friends or share images using
various Web services via CANON iMAGE GATEWAY, an online
photo service for Canon users (free registration required).
 Update the Connect Station firmware to the latest version.
 CANON iMAGE GATEWAY Web services are not supported in certain
countries and areas. For information on supported countries and areas,
refer to the Canon website (www.canon.com/cig).
3
Introduction
Easy Connection Using the NFC Function
This camera can be easily connected to an NFC-enabled smartphone
or Connect Station (sold separately) using the NFC function. For details,
see page 24.
 Note that Canon cannot be held liable for any loss or damage from
erroneous wireless communication function settings for using the camera.
In addition, Canon cannot be held liable for any other loss or damage
caused by use of the camera.
 When using wireless communication functions, establish appropriate
security at your own risk and discretion. Canon cannot be held liable for
any loss or damage caused by unauthorized access or other security
breaches.
4
Conventions Used in this Manual
 In this manual, the terms “wireless” and “wireless LAN” are used as
general terms for Wi-Fi and Canon’s original wireless
communication functions.
The term “access point” indicates wireless LAN terminals (wireless
LAN access points, wireless LAN routers, etc.) that relay wireless
LAN connection.
Icons in this Manual
<6>
: Indicates the Main Dial.
<5>
: Indicates the Quick Control Dial.
<9>
: Indicates the Multi-controller.
<0>
: Indicates the Setting button.
* In addition to the above, the icons and symbols used on the camera’s buttons
and displayed on the LCD monitor are also used in this manual when discussing
relevant operations and functionality.
(p.**) : Reference page numbers for more information.
: Warnings to prevent potential problems during operation.
: Supplemental information.
5
Structure of This Manual
This manual consists of the following five sections: “Getting Started”, “Easy
Connection”, “Advanced Connection”, “When Connected”, and “Reference”.
After preparing to connect in “Getting Started”, follow the diagram below
and see the corresponding pages according to your needs.
Getting Started (p.13)
Explains how to register a nickname and the basic operations.
Selecting Connection Destination
Connect Station
q Smartphone
D EOS Utility
l Printer
r FTP server
w Web service
Select Connection Method
For q, D, or l, you can select the
connection method.
Easy Connection (p.27)
Explains how to connect the camera
directly to the device via Wi-Fi.
Advanced Connection (p.53)
Mainly explains how to connect using a
Wi-Fi access point.
A smartphone or computer can be
connected to a camera while maintaining
connection to an access point.
When Connected (p.81)
Explains how to use the wireless functions such as sending images after a
connection is established.
Reference (p.145)
Describes the solutions to problems and other information. Read as necessary.
6
Chapters
Introduction
2
Getting Started
1
Preparation and Basic Operation
2
3
4
5
Easy Connection to a Smartphone
29
Easy Connection to Connect Station
39
Easy Connection to EOS Utility
43
Easy Connection to a Printer
49
6
7
Using a Wi-Fi Access Point
59
Connecting to an FTP Server
75
8
9
10
11
12
13
Communicating with a Smartphone
83
Operating Remotely Using EOS Utility
99
Printing Images Using a Wi-Fi Printer
103
Transferring Images to an FTP Server
113
Sending Images to a Web Service
129
Reconnecting and Adding or Changing Settings
135
14
15
Troubleshooting Guide
147
Reference
169
15
Easy Connection
Advanced Connection
When Connected
Reference
7
Contents
Introduction
2
What You Can Do Using the Wi-Fi (Wireless Communication) Functions ... 2
Conventions Used in this Manual..................................................... 5
Structure of This Manual .................................................................. 6
Chapters........................................................................................... 7
Getting Started
13
Operation Flowchart ....................................................................... 14
1
Preparation and Basic Operation
15
Registering a Nickname ................................................................. 16
Basic Operation and Settings......................................................... 19
NFC Function ................................................................................. 24
Preparation for Smartphones ......................................................... 26
Easy Connection
27
Wireless Function Operation Flowchart (Easy Connection)........... 28
2
Easy Connection to a Smartphone
29
Connection Method ........................................................................ 30
Connecting to an NFC-enabled Smartphone ................................. 31
Connecting with [Easy connection] .............................................. 34
3
Easy Connection to Connect Station
39
Saving Images................................................................................ 40
8
Contents
4
Easy Connection to EOS Utility
43
Connecting with [Easy connection]...............................................44
5
Easy Connection to a Printer
49
Connecting with [Easy connection]...............................................50
Advanced Connection
53
Wireless LAN Function Operation Flowchart (Advanced Connection) ... 54
Preparation for Web Services .........................................................56
Preparation of an FTP Server .........................................................58
6
Using a Wi-Fi Access Point
59
Checking the Type of Access Point ................................................ 60
Connecting via WPS (PBC Mode) ..................................................61
Connecting via WPS (PIN Mode).................................................... 65
Connecting to a Network Manually ................................................. 69
7
Connecting to an FTP Server
75
Configuring FTP Server Connection Settings .................................76
When Connected
81
8
83
Communicating with a Smartphone
Operating the Camera Using a Smartphone................................... 84
Sending Images to a Smartphone ..................................................87
Specifying Viewable Images ........................................................... 94
9
Contents
9
Operating Remotely Using EOS Utility
99
Using EOS Utility.......................................................................... 100
10
Printing Images Using a Wi-Fi Printer
103
Printing ......................................................................................... 104
Print Settings ................................................................................ 107
11
Transferring Images to an FTP Server
113
Transferring Images Individually .................................................. 114
Batch Transfer.............................................................................. 119
Transferring Images with a Caption ............................................. 123
Viewing Transferred Images ........................................................ 124
Terminating the Connection ......................................................... 125
Changing FTP Server Settings..................................................... 126
12
Sending Images to a Web Service
129
Sending Images to a Web Service ............................................... 130
13
Reconnecting and Adding or Changing Settings
135
Reconnecting ............................................................................... 136
Registering Multiple Connection Settings..................................... 138
Checking, Changing, or Deleting Connection Settings ................ 140
Clearing Built-in Wireless Communication Settings ..................... 143
View Info Screen .......................................................................... 144
10
Contents
Reference
14
Troubleshooting Guide
145
147
Responding to Error Messages ....................................................148
Troubleshooting Guide..................................................................165
Wireless Function Notes ...............................................................166
Security ......................................................................................... 167
Checking Network Settings...........................................................168
15
Reference
169
Creating and Registering Captions ............................................... 170
Setting up the Network Manually .................................................. 172
Setting up the IP Address Manually.............................................. 174
Specifications................................................................................176
Index ............................................................................................. 178
11
12
Getting Started
13
Operation Flowchart
This section explains how to register a nickname (for identification) and
the basic operation of the wireless functions.
Follow the procedures below.
Register a nickname. (p.16)
Set the camera’s nickname.
The default nickname (the camera name) can
be used.
Be sure to set a nickname as otherwise you
cannot set the wireless functions.
Set [Wi-Fi/NFC] to [Enable].
(Steps 1 to 4 on page 19)
Display the [Wi-Fi function] screen.
(Steps 5 and 6 on page 20)
Select a Wi-Fi function and establish a
connection.
For further settings, see “Easy Connection” or
“Advanced Connection”.
Easy Connection (p.27)
Connect the camera directly to the
device.
14
Advanced Connection (p.53)
Connect using a Wi-Fi access point.
1
Preparation and Basic
Operation
This chapter describes how to register a nickname (for
identification) necessary for using the camera’s wireless
functions and the basic operations.
15
Registering a Nickname
First, set the camera’s nickname (for identification).
When the camera is connected to another device wirelessly, the
nickname will be displayed on the device. Be sure to set a nickname
as otherwise you cannot set the wireless functions.
1
Select [Communication settings].
 Press the <M> button, select
[Communication settings] under the
[54] tab, and press <0>.
2 Select [Built-in wireless settings].
3 Select [Nickname].
 When this setting is selected for the
first time, a screen to register a
nickname is displayed. Press <0>
and proceed to step 4.
16
Registering a Nickname
a nickname.
4 Enter
 For instructions on entering
characters, see the next page.
 When using the default nickname (the
camera name), proceed to step 5.
 Otherwise, enter any characters
between 1 to 10 characters in length.
the setting.
5 Exit
 When you are finished, press the
<M> button.
 Select [OK] on the confirmation
dialog and press <0> to return to
the menu screen.
Since the nickname is a required wireless setting, you cannot delete all the
characters.
17
Registering a Nickname
Virtual Keyboard Operation
 Changing the entry area
Press the <Q> button to toggle
between the top and bottom entry
areas.
 Moving the cursor
Use <5> or <9> in the top area to
move the cursor.
 Entering text
In the bottom area, use <5> or <9> to select a character, then
press <0> to enter it.
You can check how many characters you have entered and how
many more can be entered by referring to [*/*] on the upper right of
the screen.
 Changing the entry mode*
Select [E] at the bottom right of the bottom entry area. Each
time you press <0>, the entry mode will change as follows: Lower
case 9 Numerals / Symbols 1 9 Numerals / Symbols 2 9 Upper
case.
* When [Touch control: Disable] is set, you can enter all characters on one
screen.
 Deleting a character
Press the <L> button to delete one character.
 Finishing the text entry
Press the <M> button to confirm what you have entered and exit.
If a confirmation dialog is displayed, select [OK] to exit.
 Canceling the text entry
Press the <B> button to cancel text entry and exit. If a
confirmation dialog is displayed, select [OK] to exit.
18
Basic Operation and Settings
The basic operation for using the camera’s wireless functions is
explained here. Follow the procedures below.
1
Select [Communication settings].
 Press the <M> button, select
[Communication settings] under the
[54] tab, and press <0>.
2 Select [Built-in wireless settings].
3 Select [Wi-Fi/NFC].
[Enable].
4 Select
 When a nickname (for
identification) is not registered, a
registration screen is displayed.
See page 16 to register a nickname.
 [Wi-Fi function] is now selectable.
You can operate wireless functions also by touching the camera’s screen.
19
Basic Operation and Settings
5 Select [Wi-Fi function].
the Wi-Fi function to
6 Select
connect to.
 Use <5> or <9> to select an item,
then press <0>.
 When the connection settings are not
registered, the setting screen is
displayed.
 When the connection settings are
already registered, the reconnection
screen is displayed (p.136).
 For further connection settings, see “Easy Connection” (p.27) or
“Advanced Connection” (p.53).
 When using the NFC function, see page 24.
[Built-in wireless settings] Screen
The [Built-in wireless settings] screen
displayed in step 5 is the portal screen
for setting the wireless functions.
 Select an item and press <0> to
display the setting screen, then
specify the settings.
 On the [Built-in wireless settings]
screen, you can set the following
items:
20
Basic Operation and Settings
[Wi-Fi/NFC]
Set whether to [Enable] or [Disable] the wireless functions. You can
also set whether to enable or disable the NFC function.
 Set to [Enable] to enable the selection of [Wi-Fi function], [Send
images to smartphone], and [Clear settings].
 When the use of electronic devices and wireless devices is
prohibited, such as on board airplanes or in hospitals, set it to
[Disable].
[Wi-Fi function]
The following Wi-Fi functions are available:
 Connect to smartphone
 Remote control (EOS Utility)
 Print from Wi-Fi printer
 Transfer images to FTP server
 Upload to Web service
[Send images to smartphone] (p.87)
While the camera is connected to a smartphone, use this function to
send images stored in the camera to the smartphone.
[Nickname] (p.16)
Register or change the nickname.
[Clear settings] (p.143)
Clear all built-in wireless communication settings.
21
Basic Operation and Settings
 When multiple exposures or time-lapse movie is set, you cannot select
[54: Communication settings].
Interface Cable Connection Cautions
 During a wireless LAN connection, you cannot use the camera by
connecting it to Connect Station, a computer, a wireless file transmitter,
or another device with a cable. Terminate the connection before
connecting a cable.
 When the camera is connected to Connect Station, a computer, a
wireless file transmitter, or another device with a cable, you cannot select
[Built-in wireless settings]. Disconnect the cable before changing any
settings.
Cards
 For [l] and [w], the camera cannot be connected wirelessly if a card
with images recorded is not inserted into the camera.
Using the Camera with a Wireless Connection Established
 When you want to prioritize the wireless connection, do not operate the
power switch, card slot cover, battery compartment cover, or other parts.
Otherwise, the wireless connection may be terminated.
Using an Eye-Fi Card
 When [Wi-Fi/NFC] is set to [Enable], image transfer using an Eye-Fi
card is disabled.
22
Basic Operation and Settings
Wireless Connection Status
Wireless connection status can be checked on the camera’s LCD
monitor and LCD panel.
LCD monitor
Quick Control screen
LCD panel
Information display
screen during playback
Wireless signal strength
Wi-Fi function
LCD monitor
Connection status
Wi-Fi function
Wi-Fi/NFC:
Disable
Not
connected Wi-Fi/NFC:
Enable
Connecting
LCD panel
Wireless signal
strength
Wi-Fi function
Off
(Blinking)
(Blinking)
Connected
Sending data
Connection error
Connection to FTP
server stopped
()
(Blinking)
(Blinking)
Off
*
*
is also displayed on the screen for sending images.
is not displayed when the camera is connected with [Easy connection] or
[Camera access point mode].
* For the display screen during Live View shooting, refer to the Camera Instruction
Manual.
23
NFC Function
Using an NFC-enabled smartphone or Connect Station enables you to
do the following:
 Touch a smartphone to the camera to easily connect them wirelessly
(p.31).
 While playing back images on the camera, touch a smartphone to
the camera to send a captured image to the smartphone (p.87).
 Hold the camera close to Connect Station (sold separately) to easily
connect them wirelessly (p.40).
When using the NFC function, follow the steps below to set the
camera’s NFC setting.
1
Select [Communication settings].
 Under the [54] tab, select
[Communication settings], then
press <0>.
2 Select [Built-in wireless settings].
3 Select [Wi-Fi/NFC].
What is NFC?
NFC (Near Field Communication) is a function that can exchange
information by simply bringing two NFC-enabled devices close together.
This camera uses the NFC function to exchange the data for wireless
connections.
24
NFC Function
[X] to [Allow NFC
4 Add
connections].
 Displayed when [Wi-Fi/NFC] is set to
[Enable].
 Press the <B> button to add or
remove [X]. Add [X], then press
<0>.
 When a nickname (for identification)
is not registered, a registration screen
is displayed (p.16).
When establishing wireless communications using the NFC function,
see the following pages.
Connecting to a smartphone wirelessly: page 31*
Sending images to a smartphone: page 87*
Connecting to Connect Station: page 40
* When connecting to a smartphone, see pages 26 and 30 as well.
NFC Function Cautions
 This camera cannot be connected to other NFC-enabled devices, such
as printers, using the NFC function.
 A connection cannot be established using the NFC function while
shooting with the camera, when there is no card, or while the camera is
connected to another device with an interface cable.
 To connect the camera to an NFC-enabled smartphone, the
smartphone’s Wi-Fi and NFC functions must be enabled.
A connection can be established even when the camera’s power is in the
auto power off state. However, if a connection cannot be established, cancel
auto power off, then establish a connection.
25
Preparation for Smartphones
To use [q] (Connect to smartphone), a smartphone on which iOS or
Android is installed is necessary. In addition, the dedicated application
Camera Connect (free of charge) must be installed on the smartphone.
 Camera Connect can be downloaded from the App Store or Google
Play.
 For the operating system versions supported by Camera Connect,
refer to the download site of Camera Connect.
 When an NFC-enabled smartphone is touched to the camera before
installing Camera Connect, the download screen of Camera
Connect will be displayed on the smartphone.
 Interface or functions of the camera and Camera Connect are
subject to change for firmware update of the camera or application
update of Camera Connect, iOS, Android, etc. In such a case,
features of the camera or Camera Connect may differ from sample
screens or operation instructions in this manual.
26
Easy Connection
27
Wireless Function Operation Flowchart (Easy Connection)
q
D
l
Smartphone
EOS Utility
Printer
Connect Station
Register the camera’s nickname (p.16)
Set up
Install EOS Utility on a
computer
Connect
Install Camera
Connect on a
smartphone (p.26)
Set up Connect
Station
Set up a compatible printer
(p.49)
Register connection destinations to the camera
(p.31, 34)
(p.44)
Connect via
NFC (p.40)
(p.50)
Save images
(p.40)
Use
Operate the camera
remotely (p.99)
Make images viewable
and shoot remotely
(p.83)
Print images (p.103)
 To connect to r (Transfer images to FTP server) or w (Upload to
Web service), see “Advanced Connection” (p.53).
28
2
Easy Connection to a
Smartphone
Communicating with a smartphone enables you to
perform the following:
• View images stored in the camera on a smartphone or save
viewed images to a smartphone.
• Operate the camera to take a picture or change camera
settings using a smartphone.
• Send images to a smartphone from the camera.
This section explains how to connect the camera
directly to a smartphone via Wi-Fi.
 Install Camera Connect on the smartphone before setting
up a connection (p.26).
 To connect using a Wi-Fi access point or connect manually
in camera access point mode, see “Advanced Connection”
(p.53).
 For procedures to send images to an NFC-enabled
smartphone, see page 87.
29
Connection Method
 When the smartphone is NFC-enabled: See page 31.
You can easily set up a connection using the NFC function.
 When the smartphone is not NFC-enabled: See page 34.
Set up a connection by selecting [Easy connection].
Smartphones labeled with the P mark are NFC-enabled. Some
smartphones are not labeled with the P mark even if they are NFCenabled; if you do not know whether your smartphone is NFC-enabled,
contact the manufacturer of the smartphone.
A connection may not be established with the NFC function even if the
smartphone is NFC-enabled. In such a case, establish a connection using
the procedure in “Connecting with [Easy connection]” (p.34) or “Advanced
Connection” (p.53).
NFC-enabled smartphones can also be connected by selecting [Easy
connection] or [Select a network].
30
Connecting to an NFC-enabled Smartphone
NFC-enabled smartphones can be connected by touching them to the
camera.
The operation flow is as follows.
(1) Turn on the camera and smartphone.
(2) Enable the NFC function on the camera and smartphone.
(3) Touch the smartphone to the camera so that they come into
contact with each other.
 For the camera’s NFC setting, see page 24.
 For the smartphone’s Wi-Fi setting, NFC setting, and NFC antenna
position, refer to the smartphone’s instruction manual.
the NFC function on the
1 Enable
camera and smartphone (p.24).
a smartphone to the
2 Touch
camera.
 If the download site of Camera
Connect appears on the smartphone,
install Camera Connect (p.26).
 If an image is being played back on
the camera, press the <3> button to
end the playback.
 Touch the P mark on the
smartphone to that on the camera.
 When a message indicating the
connection is being established is
displayed on the camera’s LCD
monitor, move the smartphone away
from the camera.
 Camera Connect starts on the
smartphone and establishes a
connection.
31
Connecting to an NFC-enabled Smartphone
to the camera.
3 Connect
 When a connection is established,
The device name set on
Camera Connect
the screen on the left will appear on
the camera’s LCD monitor. When
connecting to the same smartphone,
this screen will not appear again.
 To specify viewable images, press the
<B> button. See step 7 on page
96 to set them.
 Select [OK] and press <0>. After a
message is displayed, the [qWi-Fi
on] screen will appear.
 The main window of Camera Connect
will be displayed on the smartphone.
 To return to the menu, press the
<M> button.
The settings for connecting to a smartphone are now complete.
For operations after setting up a connection, see page 83.
You can check or change the device name on the setting screen of Camera
Connect.
32
Connecting to an NFC-enabled Smartphone
 If necessary, also read “NFC Function Cautions” (p.25).
 When touching the smartphone to the camera, be careful not to drop the
camera or smartphone.
 Do not touch the smartphone to the camera with too much force. Doing
so can scratch the camera or smartphone.
 Just holding the smartphone close to the mark may not establish a
connection. Be sure to touch the mark with the smartphone so that they
come into contact with each other.
 Recognition may be difficult depending on the smartphone. Touch slowly
while changing the position or rotating horizontally.
 Another application on the smartphone may start depending on how you
touch. Check the position of the P mark, then touch again.
 When touching the smartphone to the camera, do not leave anything
between the camera and smartphone. In addition, when a case is
attached to the camera or smartphone, communication may not be
possible via NFC function.
 The camera cannot be connected to two or more smartphones at the
same time.
 By default, the connection settings with the NFC function are saved as
the fourth setting (a setting dedicated to NFC connection) under the
name [SET4(NFC)]. When you connect the camera to another
smartphone via NFC, [SET4(NFC)] will be overwritten.
 While connected, the camera’s auto power off does not function.
33
Connecting with [Easy connection]
The camera and a smartphone can be directly connected via Wi-Fi.
To establish connection, operations on the smartphone are required.
For details, refer to the smartphone’s instruction manual.
Operation on the Smartphone-1
1
Install Camera Connect on the
smartphone (p.26).
Operation on the Camera-1
[Communication settings].
2 Select
 Under the [54] tab, select
[Communication settings], then
press <0>.
3 Select [Built-in wireless settings].
[Wi-Fi function].
4 Select
 Set [Wi-Fi/NFC] to [Enable], then
select [Wi-Fi function] (p.20).
 If a screen for setting a nickname (for
identification) appears, register a
nickname (p.16).
[q] (Connect to
5 Select
smartphone).
34
Connecting with [Easy connection]
[Easy connection].
6 Select
 Select [OK] and press <0> to go to
the next screen.
Operation on the Smartphone-2
Smartphone’s screen
(sample)
the smartphone and
7 Operate
connect it to the camera.
 Activate the smartphone’s Wi-Fi
function, then select the SSID
(network name) displayed on the
camera’s LCD monitor.
 For the password, enter the
encryption key displayed on the
camera’s LCD monitor.
Camera’s screen
SSID (network name)
Encryption key (password)
When connecting by selecting [Easy connection], “_Canon0A” is
displayed at the end of the SSID.
35
Connecting with [Easy connection]
Camera Connect on the
8 Start
smartphone.
 When the [Waiting to connect]
screen is displayed on the camera’s
LCD monitor, start Camera Connect
on the smartphone.
the camera to connect to
9 Select
on the smartphone.
 Select and tap the camera to connect
to from [Cameras] on Camera
Connect.
36
Connecting with [Easy connection]
Operation on the Camera-2
to the camera.
10 Connect
 When a connection is established,
The device name set on
Camera Connect
the screen on the left will appear on
the camera’s LCD monitor.
 To specify viewable images, press the
<B> button. See step 7 on page
96 to set them.
 Select [OK] and press <0>. After a
message is displayed, the [qWi-Fi
on] screen will appear.
 The main window of Camera Connect
will be displayed on the smartphone.
 To return to the menu, press the
<M> button.
The settings for connecting to a smartphone are now complete.
For operations after setting up a connection, see page 83.
 You can check or change the device name on the setting screen of
Camera Connect.
 While connected, the camera’s auto power off does not function.
37
38
3
Easy Connection to
Connect Station
Connect Station (sold separately) is a device that allows
you to import captured still photos and movies for
viewing on your TV set, smartphone, etc., or sharing
them over a network.
You can easily save still photos and movies to Connect
Station by holding this camera close to Connect Station.
39
Saving Images
This section explains how to connect the camera and Connect Station
(sold separately) wirelessly. To save images in other ways, refer to the
Connect Station Instruction Manual.
 Set up the camera to allow use of its NFC function in advance
(p.24).
the NFC function on the
1 Enable
camera (p.24).
the camera close to Connect
2 Hold
Station.
NFC connect point
 Turn on the camera and Connect
Station, then hold the camera’s P
mark close to the Connect Station’s
NFC connect point.
 When a message indicating the
connection is being established is
displayed on the camera’s LCD
monitor and Connect Station
responds, move the camera away
from Connect Station.
 When a connection is established,
Connect Station checks the images
on the memory card, then saves only
the unsaved images.
the connection.
3 Terminate
 After images are saved, the screen
on the left will appear on the camera’s
LCD monitor. Press <0> to
terminate the connection.
40
Saving Images
 If necessary, also read “NFC Function Cautions” (p.25).
 While saving images, a picture cannot be taken even if the camera’s
shutter button is pressed.
 Do not drop the camera on Connect Station or touch the camera to it with
too much force. Doing so may damage Connect Station’s internal hard
disk.
 If the camera is not recognized right away, try holding it close to Connect
Station and slowly moving it or rotating it horizontally.
 Just holding the camera close to Connect Station may not establish a
connection. In such a case, gently touch Connect Station with the
camera.
 When holding the camera close to Connect Station, do not leave
anything between the camera and Connect Station. In addition, when a
case is attached to the camera, communication may not be possible via
NFC function.
 If the camera and Connect Station are moved too far away from each
other while saving images, saving may take time or the connection may
be terminated.
 If the camera’s battery runs out while saving images, saving will stop.
Charge the battery, then try again.
 4K movies cannot be played back with Connect Station.
 When all images are already saved, saving will not be performed. In
such a case, select [OK] to terminate the connection.
 When there are a large number of images on the memory card, it may
take time to check and save the images.
 While saving images, the camera’s auto power off does not function.
41
42
4
Easy Connection to
EOS Utility
This section explains how to connect the camera
directly to a computer via Wi-Fi.
 Install EOS Utility on the computer before setting up a
connection.
 To connect using a Wi-Fi access point or connect manually
in camera access point mode, see “Advanced Connection”
(p.53).
Settings may be disabled when an older version of software is
used. Install a version of EOS Utility that is compatible with this
camera.
43
Connecting with [Easy connection]
The camera and a computer can be directly connected via Wi-Fi.
 To establish a connection, operations on the computer are required.
For details, refer to the computer’s instruction manual.
 The configuration procedure is as follows, using Windows 8.1 as an
example.
Operation on the Computer-1
1
Install EOS Utility on the
computer.
 For how to install EOS Utility, refer to
the Camera Instruction Manual.
Operation on the Camera-1
[Communication settings].
2 Select
 Under the [54] tab, select
[Communication settings], then
press <0>.
3 Select [Built-in wireless settings].
44
Connecting with [Easy connection]
[Wi-Fi function].
4 Select
 Set [Wi-Fi/NFC] to [Enable], then
select [Wi-Fi function] (p.20).
 If a screen for setting a nickname (for
identification) appears, register a
nickname (p.16).
[D] (Remote control (EOS
5 Select
Utility)).
[Easy connection].
6 Select
 Select [OK] and press <0> to go to
the next screen.
45
Connecting with [Easy connection]
Operation on the Computer-2
Computer’s screen
(sample)
the computer and
7 Operate
connect it to the camera.
 In the wireless settings of the
computer to be used, select the SSID
(network name) displayed on the
camera’s LCD monitor.
 For the password, enter the
encryption key displayed on the
camera’s LCD monitor.
Camera’s screen
SSID (network name)
Encryption key (password)
When connecting by selecting [Easy connection], “_Canon0A” is
displayed at the end of the SSID.
46
Connecting with [Easy connection]
Operation on the Camera-2
[OK].
8 Select
 Select [OK] and press <0>. The
following message is displayed.
“******” represents the last six digits of
the MAC address of the camera to be
connected.
Operation on the Computer-3
9 Start EOS Utility on the computer.
EOS Utility, click [Pairing over
10 InWi-Fi/LAN].
 If a firewall-related message is
displayed, select [Yes].
[Connect].
11 Click
 Select the camera to connect to, then
click [Connect].
47
Connecting with [Easy connection]
Operation on the Camera-3
to the camera.
12 Connect
 When the camera detects the
computer on which you clicked
[Connect] in step 11, the screen on
the left is displayed.
 Select [OK] and press <0>. The
[DWi-Fi on] screen will appear.
 To return to the menu, press the
<M> button.
The settings for connecting to EOS Utility are now complete.
For operations after setting up a connection, see page 99.
 Once pairing is complete, there is no need to complete pairing from
the next time on if you continue using the same camera and
computer together without changing the settings.
48
5
Easy Connection to a
Printer
This section explains how to connect the camera
directly to a printer via Wi-Fi.
 Connection is possible with wireless printers supporting
PictBridge (Wireless LAN).
 To connect using a Wi-Fi access point or connect manually
in camera access point mode, see “Advanced Connection”
(p.53).
When HDR shooting is set or when Multi Shot Noise Reduction is
set, the camera cannot be connected to a printer.
49
Connecting with [Easy connection]
The camera and a printer can be directly connected via Wi-Fi.
To establish a connection, operations on the printer are required. For
details, refer to the printer’s instruction manual.
1
Select [Communication settings].
 Under the [54] tab, select
[Communication settings], then
press <0>.
2 Select [Built-in wireless settings].
[Wi-Fi function].
3 Select
 Set [Wi-Fi/NFC] to [Enable], then
select [Wi-Fi function] (p.20).
 If a screen for setting a nickname (for
identification) appears, register a
nickname (p.16).
[l] (Print from Wi-Fi
4 Select
printer).
50
Connecting with [Easy connection]
[Easy connection].
5 Select
 Select [OK] and press <0> to go to
the next screen.
SSID (network name)
Encryption key (password)
the printer’s Wi-Fi settings to
6 Set
connect to the camera.
 On the Wi-Fi settings menu of the
printer to be used, select the SSID
(network name) displayed on the
camera’s LCD monitor.
 For the password, enter the
encryption key displayed on the
camera’s LCD monitor.
When connecting by selecting [Easy connection], “_Canon0A” is
displayed at the end of the SSID.
51
Connecting with [Easy connection]
the printer to connect to.
7 Select
 When a list of printers is displayed,
select the printer to connect to and
press <0>.
 Some printers may make a beeping
sound.
 When 16 or more printers are
detected or the search takes over 3
minutes, you can select [Search
again].
 When a connection is established, an
image on the card is displayed.
the images to be printed.
8 Select
 Select and print images on the
camera (p.104).
The settings for connecting to a printer are now complete.
For operations after setting up a connection, see page 103.
52
Advanced Connection
53
Wireless LAN Function Operation Flowchart (Advanced Connection)
q
D
l
Smartphone
EOS Utility
Printer
Set up
Register a nickname (p.16)
Install Camera
Connect on a
smartphone (p.26)
Install EOS Utility on
a computer
Connect each device to a Wi-Fi access point*
Use
Connect
Connect the camera to a Wi-Fi access point (p.59)
Connect the camera to each device
(p.64)
(p.68)
(p.73)
Make images
viewable and shoot
remotely (p.83)
Operate the camera
remotely (p.99)
Print images (p.103)
 To connect to Connect Station, see “Easy Connection” (p.27).
* These instructions should be followed only after each device, such as a
smartphone, is connected to a Wi-Fi access point.
* For connection using [Camera access point mode], see page 74.
54
r
w
FTP Server
Web Service
Register a nickname (p.16)
Set up a computer as
an FTP server (p.58)
• Register with CANON iMAGE
GATEWAY (p.56)
• Register Web services on the
camera (p.57)
Connect each device to
a Wi-Fi access point*
Connect the camera to a Wi-Fi access point (p.59)
Connect the camera to each
device (p.75)
Transfer images (p.113)
Save and share images (p.129)
55
Preparation for Web Services
Signing Up as a CANON iMAGE GATEWAY Member
To send images to Web services, you need to sign up as a CANON
iMAGE GATEWAY member (free of charge).
Once you are a CANON iMAGE GATEWAY member, you can publish
photos you took in online albums and use a range of services. This
website also serves as a platform for sharing images on registered Web
services. Connect to the Internet from a computer or other device,
access the Canon website (www.canon.com/cig) to check countries and
areas supporting the services, then register as a member by following
the instructions.
If you also intend to use Web services other than CANON iMAGE
GATEWAY, you must have an account with the services you intend to
use. For details, consult each individual Web service’s site.
 CANON iMAGE GATEWAY Web services are not supported in certain
countries and areas. For information on supported countries and areas,
refer to the Canon website (www.canon.com/cig).
 To use CANON iMAGE GATEWAY, you must be able to connect to the
Internet. (An account with an internet service provider is necessary,
browser software needs to be installed, and a line connection must be
completed.)
 For information on browser (e.g. Microsoft Internet Explorer) versions
and settings required to access CANON iMAGE GATEWAY, refer to the
CANON iMAGE GATEWAY site.
 Fees to connect to your provider and communication fees to access your
provider’s access point are charged separately.
 If there has been a change in the service features of registered Web
services, operation may be different from the description in this manual,
or operation may not be possible.
 For member registration, refer to Help on the CANON iMAGE GATEWAY
site.
For Web services that can be used with this camera’s wireless functions,
refer to the CANON iMAGE GATEWAY site.
56
Preparation for Web Services
Configuring Settings to Use Web Services
Start EOS Utility on the computer, log in to CANON iMAGE GATEWAY,
then configure the camera’s settings to enable access to Web services.
For details, refer to the EOS Utility Instruction Manual. For how to
obtain the EOS Utility Instruction Manual, refer to the Camera
Instruction Manual.
The general procedure for sending images to a Web service is as
follows.
1
Install EOS Utility on a computer.
If you have already installed it, proceed to step 2.
2 Access Canon website from the computer and sign up
as a CANON iMAGE GATEWAY member (free of charge).
If you are already a member, proceed to step 3.
3 Connect the camera and computer with the provided
interface cable.
You can also configure the settings by connecting the camera and
computer via Wireless LAN (p.59) instead of an interface cable.
4 Start EOS Utility on the computer, log in to CANON
iMAGE GATEWAY, then configure the camera’s settings
to enable access to Web services.
For details, refer to the EOS Utility Instruction Manual.
5 Disconnect the interface cable.
6 Connect the camera to a Wi-Fi access point (p.59).
7 Send images to a Web service registered on the camera
(p.129).
You can share images with your family and friends by sending
images from the camera to a Web service registered on the camera
or by sending Web links of the online albums.
57
Preparation of an FTP Server
Use of [r] (Transfer images to FTP server) requires that one of the
following operating systems be installed on a computer. In addition, the
computer must be set up as an FTP server in advance.
• Windows 8, Windows 8 Pro, Windows 8.1, Windows 8.1 Pro
• Windows 7 (Professional, Enterprise, or Ultimate Edition for 32or 64-bit systems)
• Windows Vista (Business, Enterprise, or Ultimate Edition for 32or 64-bit systems)
For instructions on setting up a computer as an FTP server, refer to the
documentation provided with each device or contact the manufacturer.
Note that the following operating systems cannot be used because
FTP server functionality is not provided.
• Windows 7 Home Premium
• Windows Vista Home Premium or Home Basic Edition
58
6
Using a Wi-Fi Access
Point
This section mainly explains how to connect using a
Wi-Fi access point. When you connect to a Wi-Fi
access point, you can use the following functions:
•
•
•
•
•
Communicating with a smartphone
Operating remotely using EOS Utility
Printing images using a Wi-Fi printer
Transferring images to an FTP server
Sending images to a Web service
59
Checking the Type of Access Point
To start with, check if the access point supports WPS* that allows easy
connection between Wi-Fi devices.
If you do not know if the access point you use is WPS-compatible, refer
to the access point instruction manual or other documentation.
* Wi-Fi Protected Setup
 When WPS is supported
The following two connection methods are available. Connection
can be established easier with WPS (PBC mode).
• Connecting via WPS (PBC mode): Perform the operations
described on page 61.
• Connecting via WPS (PIN mode): Perform the operations
described on page 65.
 When WPS is not supported
• Connecting to a detected network manually: Perform the
operations described on page 69.
Access Point Encryption
This camera supports the following options for [Authentication] and
[Encryption settings]. Therefore, when connecting to a detected
network manually, the encryption used by the access point must be one
of the following.
 [Authentication]: Open system, Shared key, or WPA/WPA2-PSK
 [Encryption settings]: WEP, TKIP, or AES
 If stealth functions of the access point are active, connection may
be disabled. Deactivate stealth functions.
 When connecting to a network that has a network administrator, ask the
administrator about the detailed setting procedures.
If the network you use filters by MAC address, register the MAC address of
the camera at the access point. The MAC address can be checked on the
[View info] screen (p.144).
60
Connecting via WPS (PBC Mode)
This is a connection mode available when using an access point
compatible with WPS. In pushbutton connection mode (PBC mode), the
camera and the access point can be connected simply by pressing the
WPS button on the access point.
 If multiple access points are active in the surrounding area, it may be
more difficult to establish a connection. In such a case, try using
[WPS (PIN mode)] to establish a connection.
 Check the position of the WPS button on the access point in
advance.
 It may take approx. one minute to establish a connection.
1
Select [Communication settings].
 Under the [54] tab, select
[Communication settings], then
press <0>.
2 Select [Built-in wireless settings].
[Wi-Fi function].
3 Select
 Set [Wi-Fi/NFC] to [Enable], then
select [Wi-Fi function] (p.20).
 If a screen for setting a nickname (for
identification) appears, register a
nickname (p.16).
61
Connecting via WPS (PBC Mode)
an item.
4 Select
 Use <5> or <9> to select an item,
then press <0>.
 When you select [w] (Upload to Web
service), a screen to select a Web
service is displayed. Select a Web
service and press <0>.
 Depending on the selected Web
service, the [Send to] screen is
displayed. Select a destination (p.74).
[Select a network].
5 Select
 Displayed when [q], [D], or [l] is
selected in step 4. Go to step 6 when
selecting [r] or [w].
 Select [OK] and press <0> to go to
the next screen.
6 Select [Connect with WPS].
For [Camera access point mode] displayed in step 6, see page 74.
62
Connecting via WPS (PBC Mode)
[WPS (PBC mode)].
7 Select
 Select [OK] and press <0> to go to
the next screen.
to the access point.
8 Connect
 Press the access point’s WPS button.
For details about where the button is
located and how long to press it, refer
to the access point’s instruction
manual.
 Select [OK] and press <0> to
establish a connection with the
access point.
 When a connection with the access
point is established, the next screen
is displayed.
[Auto setting].
9 Select
 Select [OK] and press <0> to
display the setting screen for the
Wi-Fi function selected in step 4
(p.64).
 If [Auto setting] results in an error or
if you want to specify the settings
manually, see page 174.
The IP address can only be set automatically in environments using DHCP
servers, or access points or routers with DHCP server functionality, such
that the IP addresses, etc. are required to be assigned automatically.
63
Connecting via WPS (PBC Mode)
Specifying Settings for the Wi-Fi Function
This section explains how to set the screens for the Wi-Fi function.
Read the page that introduces the selected Wi-Fi function.
Communicating with a
Smartphone
 Step 8 on page 36
Operating Remotely Using EOS
Utility
 Step 8 on page 47
Printing Images Using a Wi-Fi
Printer
 Step 7 on page 52
Transferring Images to an FTP
Server
 Chapter 7 “Connecting to an FTP
Server” (p.75)
Sending Images to a Web Service
The settings for connecting to a Web
service are now complete.
 Chapter 12 “Sending Images to a
Web Service” (p.129)
64
Connecting via WPS (PIN Mode)
This is a connection mode available when using an access point
compatible with WPS. In PIN code connection mode (PIN mode), an 8digit identification number specified on the camera is set at the access
point to establish a connection.
 Even if there are multiple access points active in the surrounding
area, a relatively reliable connection can be established using this
shared identification number.
 It may take approx. one minute to establish a connection.
1
Select [Communication settings].
 Under the [54] tab, select
[Communication settings], then
press <0>.
2 Select [Built-in wireless settings].
[Wi-Fi function].
3 Select
 Set [Wi-Fi/NFC] to [Enable], then
select [Wi-Fi function] (p.20).
 If a screen for setting a nickname (for
identification) appears, register a
nickname (p.16).
65
Connecting via WPS (PIN Mode)
an item.
4 Select
 Use <5> or <9> to select an item,
then press <0>.
 When you select [w] (Upload to Web
service), a screen to select a Web
service is displayed. Select a Web
service and press <0>.
 Depending on the selected Web
service, the [Send to] screen is
displayed. Select a destination (p.74).
[Select a network].
5 Select
 Displayed when [q], [D], or [l] is
selected in step 4. Go to step 6 when
selecting [r] or [w].
 Select [OK] and press <0> to go to
the next screen.
6 Select [Connect with WPS].
[WPS (PIN mode)].
7 Select
 Select [OK] and press <0> to go to
the next screen.
For [Camera access point mode] displayed in step 6, see page 74.
66
Connecting via WPS (PIN Mode)
the PIN code at the
8 Specify
access point.
 At the access point, specify the 8-digit
PIN code displayed on the camera’s
LCD monitor.
 For instructions on setting PIN codes
at the access point, refer to the
access point’s instruction manual.
 After the PIN code is specified, select
[OK] and press <0>.
to the access point.
9 Connect
 Select [OK] and press <0> to
establish a connection with the
access point.
 When a connection with the access
point is established, the next screen
is displayed.
[Auto setting].
10 Select
 Select [OK] and press <0> to
display the setting screen for the WiFi function selected in step 4 (p.68).
 If [Auto setting] results in an error or
if you want to specify the settings
manually, see page 174.
The IP address can only be set automatically in environments using DHCP
servers, or access points or routers with DHCP server functionality, such
that the IP addresses, etc. are required to be assigned automatically.
67
Connecting via WPS (PIN Mode)
Specifying Settings for the Wi-Fi Function
This section explains how to set the screens for the Wi-Fi function.
Read the page that introduces the selected Wi-Fi function.
Communicating with a
Smartphone
 Step 8 on page 36
Operating Remotely Using EOS
Utility
 Step 8 on page 47
Printing Images Using a Wi-Fi
Printer
 Step 7 on page 52
Transferring Images to an FTP
Server
 Chapter 7 “Connecting to an FTP
Server” (p.75)
Sending Images to a Web Service
The settings for connecting to a Web
service are now complete.
 Chapter 12 “Sending Images to a
Web Service” (p.129)
68
Connecting to a Network Manually
Establish a connection by selecting the SSID (or ESS-ID) of the access
point to connect to from a list of active access points nearby.
Selecting the Access Point
1
Select [Communication settings].
 Under the [54] tab, select
[Communication settings], then
press <0>.
2 Select [Built-in wireless settings].
[Wi-Fi function].
3 Select
 Set [Wi-Fi/NFC] to [Enable], then
select [Wi-Fi function] (p.20).
 If a screen for setting a nickname (for
identification) appears, register a
nickname (p.16).
an item.
4 Select
 Use <5> or <9> to select an item,
then press <0>.
 When you select [w] (Upload to Web
service), a screen to select a Web
service is displayed. Select a Web
service and press <0>.
 Depending on the selected Web
service, the [Send to] screen is
displayed. Select a destination (p.74).
69
Connecting to a Network Manually
[Select a network].
5 Select
 Displayed when [q], [D], or [l] is
selected in step 4. Go to step 6 when
selecting [r] or [w].
 Select [OK] and press <0> to go to
the next screen.
(1)
(2) (3)
an access point.
6 Select
 Use <5> or <9> to select the
access point to connect to from the
list of access points.
(1) SSID
(2) An icon is displayed if the access point is encrypted
(3) Channel used
[Refresh] and [Manual settings]
 Scroll down the screen in step 6 to display [Refresh] and [Manual
settings].
 To search for access points again, select [Refresh].
 To configure settings for the access point manually, select [Manual
settings]. Enter the SSID using the virtual keyboard and then
configure settings following the instructions displayed.
For [Camera access point mode] displayed in step 6, see page 74.
70
Connecting to a Network Manually
Entering the Access Point Encryption Key
 Enter the encryption key (password) specified for the access point.
For details on the specified encryption key, refer to the access
point’s instruction manual.
 The screens displayed in steps 7 to 9 below vary depending on the
authentication and encryption specified for the access point.
 Go to step 10 when the [IP address set.] screen is displayed
instead of the screens for steps 7 to 9.
a key index.
7 Select
 The [Key index] screen is displayed
only if WEP encryption is used by the
access point.
 Select the key index number
specified for the access point, then
press <0>.
 Select [OK] and press <0> to go to
the next screen.
the format and the number
8 Select
of characters used for the key.
 Select [OK] and press <0> to go to
the next screen.
the encryption key.
9 Enter
 Enter the encryption key using the
virtual keyboard (p.18), then press
the <M> button.
 The [IP address set.] screen (p.72)
will be displayed.
71
Connecting to a Network Manually
Setting the IP Address
[Auto setting].
10 Select
 Select [OK] and press <0> to
display the setting screen for the Wi-Fi
function selected in step 4 (p.73).
 If [Auto setting] results in an error or
if you want to specify the settings
manually, see page 174.
The IP address can only be set automatically in environments using DHCP
servers, or access points or routers with DHCP server functionality, such
that the IP addresses, etc. are required to be assigned automatically.
72
Connecting to a Network Manually
Specifying Settings for the Wi-Fi Function
This section explains how to set the screens for the Wi-Fi function.
Read the page that introduces the selected Wi-Fi function.
Communicating with a
Smartphone
 Step 8 on page 36
Operating Remotely Using EOS
Utility
 Step 8 on page 47
Printing Images Using a Wi-Fi
Printer
 Step 7 on page 52
Transferring Images to an FTP
Server
 Chapter 7 “Connecting to an FTP
Server” (p.75)
Sending Images to a Web Service
The settings for connecting to a Web
service are now complete.
 Chapter 12 “Sending Images to a
Web Service” (p.129)
73
Connecting to a Network Manually
Send To Screen
When [w] is selected in [Wi-Fi function], a screen to select a destination
may be displayed depending on the type or settings of the Web service you
select.
To register destinations or to specify the settings, you must use a computer.
For more information, refer to the EOS Utility Instruction Manual.
 When [m] (Email) or other service is
selected on the [Upload to Web
service] screen, the [Send to] screen
may be displayed.
 Select the destination from the list of
registered destinations and press
<0>.
 The procedures for setting up a
connection and sending images are
the same as those for other Web
services.
Camera Access Point Mode
Camera access point mode is a
connection mode for connecting the
camera directly to each device.
Displayed when [q], [D], or [l] is
selected in [Wi-Fi function].
In camera access point mode, the
following two connection methods are
available.
 [Easy connection]: See “Easy
Connection” (p.27) to establish a
connection.
 [Manual connection]: See page 172
to establish a connection.
74
7
Connecting to
an FTP Server
By connecting to an FTP server, you can transfer
images stored in the camera to a computer.
With FTP transfer, you can automatically transfer
images to the FTP server as you shoot or transfer a set
of shots together.
 The instructions in this chapter are continued from
Chapter 6.
75
Configuring FTP Server Connection Settings
These instructions are continued from Chapter 6.
 Set up the computer to connect to as an FTP server before setting
up a connection (p.58).
1
Select an FTP mode.
 To establish security for FTP transfer
using a root certificate, select [FTPS].
 For root certificate settings, see page
79.
 Select [OK] and press <0> to go to
the next screen.
[Address setting].
2 Select
 The virtual keyboard is displayed.
the FTP server’s server
3 Enter
name or IP address.
 With the IP address set to [Auto
setting] or the DNS address set to
[Manual setting], the screen on the
left is displayed.
 For instructions on screen operations,
see “Virtual Keyboard Operation”
(p.18).
 With the DNS address set to
[Disable], the screen on the left is
displayed.
 Turn the <6> dial to move the input
position in the upper area and turn
the <5> dial to select the number.
Press <0> to enter the selected
number.
76
Configuring FTP Server Connection Settings
the port number.
4 Set
 [Port number setting] should usually
be 00021.
 Select [OK] and press <0> to go to
the next screen.
the passive mode setting.
5 Set
 Select [OK] and press <0> to go to
the next screen.
 If an Error 41 (“Cannot connect to
FTP server”) is displayed in step 9,
setting [Passive mode] to [Enable]
may resolve it.
the proxy server.
6 Set
 Select [OK] and press <0> to go to
the next screen.
the login method.
7 Set
 Select [OK] and press <0> to go to
the next screen.
77
Configuring FTP Server Connection Settings
the target folder.
8 Set
 Select [Root folder] to have images
saved in the root folder as specified in
FTP server settings (p.124).
 Select [Select folder] to specify a
target folder in the root folder. If no
folder exists, a folder will be created
automatically.
 Select [OK] and press <0> to go to
the next screen.
[OK].
9 Select
 Press <0>. The [rWi-Fi on]
screen will appear.
 To return to the menu, press the
<M> button.
The connection settings for FTP transfer are now complete.
For operations after setting up a connection, see page 113.
78
Configuring FTP Server Connection Settings
Importing a Root Certificate for FTPS
If the FTP mode is set to [FTPS] when configuring the connection
settings, the same root certificate as the FTP server must be imported
to the camera. Insert a card containing the root certificate file into the
camera, then perform the following operation.
 Only a root certificate whose file name is “root.cer”, “root.crt”, or
“root.pem” (case insensitive) can be imported to the camera.
 Only one root certificate file can be imported to the camera. Import is
not possible if the card contains two or more root certificates.
1
Select [Communication settings].
 Under the [54] tab, select
[Communication settings], then
press <0>.
2 Select [FTP transfer settings].
79
Configuring FTP Server Connection Settings
3 Select [Set root certif].
[Load root certif from
4 Select
card].
[OK].
5 Select
 The root certificate is imported.
 Select [OK] on the confirmation
dialog to return to the [Set root certif]
screen.
 Select [Delete root certificate] on the screen for step 4 to delete the
root certificate imported to the camera. Select [View root certificate
details] to check the issuer, subject, validity period, and other
information.
You can import a certificate from the card selected for [Record/play] or
[Playback] under [51: Record func+card/folder sel.].
80
When Connected
81
This section explains how to use the camera after a connection is
established.
See the following pages according to your needs.
 Communicating with a Smartphone
Operating the Camera Using a Smartphone ...............................p.84
Sending Images to a Smartphone ...............................................p.87
Specifying Viewable Images ........................................................p.94
 Operating Remotely Using EOS Utility
Using EOS Utility .......................................................................p.100
 Printing Images Using a Wi-Fi Printer
Printing.......................................................................................p.104
Print Settings .............................................................................p.107
 Transferring Images to an FTP Server
Transferring Images Individually ................................................ p.114
Batch Transfer ........................................................................... p.119
Transferring Images with a Caption ...........................................p.123
Viewing Transferred Images ......................................................p.124
Terminating the Connection .......................................................p.125
Changing FTP Server Settings ..................................................p.126
 Sending Images to a Web Service
Sending Images to a Web Service ............................................p.130
 Reconnecting and Adding Settings
Reconnecting.............................................................................p.136
Registering Multiple Connection Settings ..................................p.138
 Checking and Operating Connection Settings
Checking, Changing, or Deleting Connection Settings..............p.140
Clearing Built-in Wireless Communication Settings...................p.143
View Info Screen........................................................................p.144
82
8
Communicating with a
Smartphone
Communicating with a smartphone enables you to
perform the following:
• View images stored in the camera on a smartphone or save
viewed images to a smartphone.
• Operate the camera to take a picture or change camera
settings using a smartphone.
• Send images to a smartphone from the camera.
83
Operating the Camera Using a Smartphone
You can use a smartphone with Camera Connect installed to view
images stored in the camera or perform remote shooting, etc.
Camera Connect Main Window
The main functions of Camera Connect
are described below. Touch the screen to
learn the operation procedures.
[Images on camera]
 Images stored in the camera can be
viewed.
 Images stored in the camera can be
saved on a smartphone.
 Operations such as deletion can be
performed on images stored in the
camera.
[Remote shooting]
 The camera’s Live View image can
be viewed using a smartphone.
 You can shoot using remote
operation.
[Camera settings]
 Camera settings can be changed.
v(Settings button)
 Use this button to access various
settings for Camera Connect.
84
Operating the Camera Using a Smartphone
Terminating the Connection
To terminate the connection, perform either of the following operations.
On the smartphone’s Camera
Connect screen, tap [t].
On the camera’s [qWi-Fi on]
screen, select [Disconnect,exit].
 If the [qWi-Fi on] screen is not
displayed, select the [54] tab 9
[Communication settings] 9
[Built-in wireless settings] 9
[Wi-Fi function].
 Select [Disconnect,exit], then select
[OK] on the confirmation dialog to
terminate the connection.
85
Operating the Camera Using a Smartphone
 When the wireless connection is terminated while recording a movie with
remote shooting, the camera responds as follows:
• When the Live View shooting/Movie shooting switch is set to <k>,
movie shooting continues.
• When the Live View shooting/Movie shooting switch is set to <A>,
movie shooting stops.
 When the Live View shooting/Movie shooting switch is set to <A> and
the movie mode is set by operating Camera Connect, you cannot shoot
by operating the camera.
 While connected, certain menu items are unavailable.
 In remote shooting, the AF speed may become slower.
 Depending on the connection status, image display or shutter release
may be delayed.
 When saving images to a smartphone, you cannot take a picture even if
you press the camera’s shutter button. Also, the camera’s LCD monitor
may turn off.
 Even if MOV-format movies are displayed in the list, they cannot be
saved to a smartphone.
 The wireless connection will stop if you set the camera’s power to
<2> or open the card slot cover or battery compartment cover.
 When saving RAW images to a smartphone, they are saved as JPEG
images.
 While connected, the camera’s auto power off does not function.
 While connected, disabling the smartphone’s power saving function is
recommended.
86
Sending Images to a Smartphone
Operate the camera to send images to a smartphone. The following
three send methods are available:
(1) While playing back an image, connect to a smartphone using the
NFC function.
(2) During a wireless connection, select [Send images to smartphone]
from the camera menu (p.88).
(3) During a wireless connection, send images from the Quick Control
screen during playback (p.90).
(1) Connecting with the NFC Function
While playing back an image on the camera, touch an NFC-enabled
smartphone to the camera to send the image.
 If a connection is already established wirelessly, terminate the
connection and then play back an image on the camera.
 Set up the camera to allow use of its NFC function in advance
(p.24).
 For the smartphone’s Wi-Fi setting, NFC setting, and NFC antenna
position, refer to the smartphone’s instruction manual.
the NFC function on the
1 Enable
camera and smartphone (p.24).
back the image.
2 Play
 Press the <3> button to play back
images.
87
Sending Images to a Smartphone
a smartphone to the camera.
3 Touch
 Touch the P mark on the
smartphone to that on the camera.
 If the download site of Camera
Connect appears on the smartphone,
install Camera Connect (p.26).
 When a message indicating the
connection is displayed on the
camera’s LCD monitor, move the
smartphone away.
the images to send.
4 Select
 Select and send image(s). For
information on how to send images,
see page 91.
 When the index display is selected in
step 2, the multiple image selection
screen will appear. See step 3 on
page 92.
(2) Selecting [Send images to smartphone]
While the camera is connected to a smartphone wirelessly, select
[Send images to smartphone] and send.
1
Connect the camera to a
smartphone wirelessly.
 For connection methods, see page 29
or 59.
[Communication settings].
2 Select
 Under the [54] tab, select
[Communication settings], then
press <0>.
88
Sending Images to a Smartphone
3 Select [Built-in wireless settings].
[Send images to
4 Select
smartphone].
 Select [Send images to
smartphone] on the [Built-in
wireless settings] screen, then
press <0>.
the images to send.
5 Select
 Select and send image(s). For
information on how to send images,
see page 91.
89
Sending Images to a Smartphone
(3) Quick Control During Playback
While the camera is wirelessly connected to a smartphone, send
images from the Quick Control screen during playback.
1
Connect the camera to a
smartphone wirelessly.
 For connection methods, see page 29
or 59.
back the image and press
2 Play
the <Q> button.
3 Select [q].
the images to send.
4 Select
 Select and send image(s). For
information on how to send images,
see page 91.
90
Sending Images to a Smartphone
Sending Images Individually
Select and send images individually.
1
Select an image to send.
 Turn the <5> dial to select an image
to send, then press <0>.
 If you press the <u> button and turn
the <6> dial counterclockwise, you
can select an image from the index
display.
[Send img shown].
2 Select
 To select a size at which to send the
image, select [Resize image] and
press <0>.
 Select [Send img shown] and press
<0> to send the image displayed.
 When the transfer is complete, the
screen for step 1 will reappear.
 To send another image, repeat steps
1 and 2.
Sending Multiple Images
Select multiple images and send them at once.
If the multiple image selection screen is already displayed, start the
operation from step 3.
1 Press <0>.
[Send selected].
2 Select
 To select a size at which to send the
images, select [Resize image] and
press <0>.
91
Sending Images to a Smartphone
the images to send.
3 Select
 Turn the <5> dial to select an image
to send, then add [X]. Press <0> to
add or remove [X].
 If you press the <u> button and turn
the <6> dial counterclockwise, you
can select images from a three-image
display.
 After selecting the images to send,
press the <Q> button.
[Resize image].
4 Select
 Set it as necessary.
 On the displayed screen, select an
image size, then press <0>.
[Send].
5 Select
 The selected images will be sent.
When the transfer is complete, the
screen for step 1 will reappear.
 To send other images, repeat steps 1
to 5.
92
Sending Images to a Smartphone
Ending Image Transfer
To end the image transfer, press the
<M> button on the image transfer
screen.
 If you have established the
connection with the NFC function
while playing back an image, the
connection termination screen will
appear. Select [OK] to terminate the
connection.
 If you have sent images with the
menu or Quick Control, the previous
screen will reappear. The connection
will not be terminated.
 If necessary, also read “NFC Function Cautions” (p.25).
 During the image transfer operation, a picture cannot be taken even if
the camera’s shutter button is pressed.
 Images cannot be sent using the NFC function while the camera is
connected to another device wirelessly. In addition, the camera cannot
be connected to multiple smartphones at the same time.
 Even if MOV-format movies are displayed in the list, they cannot be
saved to a smartphone.
 You can cancel the image transfer by selecting [Cancel] during the
transfer.
 You can select up to 50 files at a time.
 While connected, disabling the smartphone’s power saving function is
recommended.
 Settings for image transfer using the NFC function are not saved on the
camera.
 When you reduce the image size, all images to be sent at the same time
are resized. Note that movies or still photos that are smaller than b size
are not reduced.
 When you use a battery to power the camera, make sure it is fully
charged.
 While connected, the camera’s auto power off does not function.
93
Specifying Viewable Images
You can specify images viewable from a smartphone by operating the
camera. Images can be specified during connection setup or after
the connection is terminated.
1
Select [Communication settings].
 Under the [54] tab, select
[Communication settings], then
press <0>.
2 Select [Built-in wireless settings].
[Wi-Fi function].
3 Select
 Set [Wi-Fi/NFC] to [Enable], then
select [Wi-Fi function] (p.20).
94
Specifying Viewable Images
[q].
4 Select
 If the [qWi-Fi on] screen appears,
select [Disconnect,exit].
5 Select [Review/change settings].
6 Select [Viewable imgs].
If [Viewable imgs] is set to any setting other than [All images], remote
shooting is not possible.
When reconnecting to a smartphone, check the settings of viewable images
before establishing a connection.
95
Specifying Viewable Images
an item.
7 Select
 Select [OK] and press <0> to
display the setting screen.
[All images]
All images stored on the card become viewable.
[Images from past days]
Specify viewable images on the
shooting-date basis. Images shot up to
nine days ago can be specified.
 Select an item, then press <0>.
 When [Images shot in past days] is
selected, images shot up to the
specified number of days before the
current date become viewable. When
<r> is shown for the number of
days, turn the <5> dial to specify the
number of days, then press <0> to
complete the selection.
 Select [OK] and press <0> to
specify the viewable images.
[Select by rating]
Specify viewable images depending on
whether a rating is appended (or not
appended) or by the type of rating.
 Select a rating, then press <0> to
specify the viewable images.
96
Specifying Viewable Images
[File number range] (Select range)
First image
Last image
Select the first and last images from
images arranged by the file number to
specify the viewable images.
1 Use <5> or <9> to select the first
image file.
2 Press <0> to display the image
selection screen.
Turn the <5> dial to select an
image.
If you press the <u> button and turn
the <6> dial counterclockwise, you
can select an image from the index
display.
3 Select an image and press <0> to
complete the selection.
4 Use the same operation to specify the
last image file to be set as viewable.
Select an image shot later than the
image selected as the first image.
5 When the first and last images are
specified, select [OK], then press
<0>.
97
98
9
Operating Remotely
Using EOS Utility
You can perform remote operation using EOS Utility
wirelessly. In addition to remote shooting, various
camera operations are available because wireless
communications are used instead of an interface cable.
99
Using EOS Utility
For EOS Utility instructions, refer to the EOS Utility Instruction Manual
(CD-ROM). In addition to remote shooting, various camera operations
are available.
100
Using EOS Utility
Terminating the Connection
On the [DWi-Fi on] screen,
select [Disconnect,exit].
 If the [DWi-Fi on] screen is not
displayed, select the [54] tab 9
[Communication settings] 9
[Built-in wireless settings] 9
[Wi-Fi function].
 Select [Disconnect,exit], then select
[OK] on the confirmation dialog to
terminate the connection.
 When the wireless connection is terminated while recording a movie with
remote shooting, the camera responds as follows:
• When the Live View shooting/Movie shooting switch is set to <k>,
movie shooting continues.
• When the Live View shooting/Movie shooting switch is set to <A>,
movie shooting stops.
 When the Live View shooting/Movie shooting switch is set to <A> and
the movie mode is set using EOS Utility, you cannot shoot by operating
the camera.
 While connected, some menu items are unavailable.
 In remote shooting, the AF speed may become slower.
 Depending on the connection status, image display or shutter release
may be delayed.
 In Remote Live View shooting, the rate of image transmission is slower
compared to a connection via an interface cable. Therefore, moving
subjects cannot be displayed smoothly.
The wireless connection will stop if you set the camera’s power to <2>
or open the card slot cover or battery compartment cover.
101
102
10
Printing Images Using
a Wi-Fi Printer
You can print images by wirelessly connecting the
camera to a printer compliant to the PictBridge
(Wireless LAN).
103
Printing
Printing Images Individually
Select and print images individually.
1
Select an image to print.
 Turn the <5> dial to select an image
to print, then press <0>.
 If you press the <u> button and turn
the <6> dial counterclockwise, you
can select an image from the index
display.
[Print image].
2 Select
 The print setting screen will appear.
the image.
3 Print
 For the print setting procedures, see
page 107.
 When [Print] is selected, printing
starts.
 When printing is completed, the
screen for step 1 will reappear. To
print another image, repeat steps 1 to
3.
the connection.
4 Terminate
 Press the <M> button to display
the confirmation dialog. Select [OK],
then press <0> to terminate the
connection.
 The [Wi-Fi function] screen will
reappear.
104
Printing
Printing by Specifying the Options
Print by specifying the printing options.
1 Press <0>.
[Print order].
2 Select
 The [Print order] screen will appear.
the printing options.
3 Set
 For the setting procedures, refer to
“Digital Print Order Format (DPOF)”
in the Camera Instruction Manual.
 If the print order has been completed
before connection, proceed to step 4.
[Print].
4 Select
 [Print] can be selected only when an
image is selected and printer is ready
to print.
settings] (p.107).
5 SetSetthethe[Paper
printing effects (p.109) as
necessary.
Select [OK].
6  When printing is completed, the
screen for step 3 will reappear.
105
Printing
the connection.
7 Terminate
 Press the <M> button to return to
the screen in step 1.
 Press the <M> button again to
display the confirmation dialog.
Select [OK], then press <0> to
terminate the connection.
 The [Wi-Fi function] screen will
reappear.
 While connected to a printer, a picture cannot be taken even if the
camera’s shutter button is pressed.
 Movies cannot be printed.
 Before printing, be sure to set the paper size.
 Certain printers may not imprint the file number.
 If [Bordered] is set, certain printers may imprint the date on the border.
 Depending on the printer, the date may appear faint if it is imprinted on a
bright background or on the border.
 RAW images cannot be printed by selecting [Print order]. When printing,
select [Print image] and print.
 When you use a battery to power the camera, make sure it is fully
charged.
 Depending on the image’s file size and image-recording quality, it may
take some time to start printing after you select [Print].
 To stop printing, press <0> while [Stop] is displayed, then select [OK].
 When printing with [Print order], if you stopped printing and want to
resume printing of the remaining images, select [Resume]. Note that
printing will not resume if any of the following occurs.
• You changed the print order or erased any of the print ordered images
before resuming printing.
• When index is set, you changed the paper setting before resuming
printing.
• The card’s remaining capacity was low when you paused printing.
 If a problem occurs during printing, see page 112.
106
Print Settings
Specify settings for printing as necessary.
The screen display and setting options will differ depending on the
printer. Some settings may not be available. For details, refer to the
printer’s instruction manual.
Print setting screen
Sets the printing effects (p.109).
Sets the date or file number imprinting to on or
off (p.110).
Sets the quantity to be printed (p.110).
Sets the print area (p.111).
Sets the paper size, type, and layout (p.108).
Returns to the image selection screen.
Starts the printing.
The paper size, type, and layout you have set are displayed.
* Depending on the printer, certain settings such as the date and file
number imprinting and cropping may not be selectable.
Paper Settings
 Select [Paper settings], then press
<0>.
 The paper settings screen will
appear.
107
Print Settings
Q Setting the Paper Size
 Select the size of the paper loaded in
the printer, then press <0>.
 The paper type screen will appear.
Y Setting the Paper Type
 Select the type of the paper loaded in
the printer, then press <0>.
 The page layout screen will appear.
U Setting the Page Layout
 Select the page layout, then press
<0>.
 The print setting screen will reappear.
Bordered
Prints with white borders along the edges.
Borderless
Prints with no borders. If your printer cannot print borderless
prints, the print will have borders.
xx-up
Option to print 2, 4, 8, 9, 16, or 20 images on one sheet.
Default
The page layout varies depending on the printer model or its
settings.
If the image’s aspect ratio is different from the printing paper’s aspect ratio,
the image may be cropped significantly when you print it as a borderless
print. If the image is cropped, the print may look grainier due to the fewer
number of pixels.
108
Print Settings
Setting the Printing Effects (Image Optimization)
 Contents displayed on the screen
vary depending on the printer.
 Select the option, then press <0>.
 Select the desired printing effect, then
press <0>.
Printing Effect
Description
EOn
Prints with the printer’s standard colors. The image’s Exif
information is used to make automatic corrections.
EOff
No automatic correction is applied.
ERed-Eye1
Effective in flash photography images where the subject has
red eye. The red eye is reduced before printing.
EDefault
Printing differs depending on the printer. For details, refer to the
printer’s instruction manual.
If you imprint shooting information on an image shot at an ISO speed of H1
or H2, the correct ISO speed may not be imprinted.
109
Print Settings
Setting the Date/File Number Imprinting
 Select [I], then press <0>.
 Set the print settings as desired, then
press <0>.
Setting the Number of Copies
 Select [R], then press <0>.
 Set the number of copies, then press
<0>.
The [Default] setting for printing effects and other options are the printer’s
own default settings as set by the printer’s manufacturer. Refer to the
printer’s instruction manual to find out what the [Default] settings are.
110
Print Settings
Cropping the Image
You can crop the image and print only an
enlarged version of the cropped portion,
as if the image is recomposed.
Set the cropping right before printing.
If you change the print settings after
setting the cropping, you may have to set
the cropping again before printing.
1 On the print setting screen, select [Cropping].
2 Set the cropping frame size, position, and aspect ratio.
 The image area within the cropping frame will be printed. The
cropping frame’s aspect ratio can be changed with [Paper
settings].
Changing the Cropping Frame Size
Turn the <6> dial to change the cropping frame size. The
smaller the cropping frame, the larger the image magnification
will be for printing.
Moving the Cropping Frame
Use <9> to move the frame over the image vertically or
horizontally. Move the cropping frame until it covers the desired
image area.
Switching the Orientation of the Cropping Frame
Pressing the <B> button will toggle the cropping frame
between the vertical and horizontal orientations. This enables
you to create a vertically oriented print from a horizontal image.
3 Press <0> to exit the cropping.
 The print setting screen will reappear.
 You can check the cropped image area on the upper left of the
print setting screen.
111
Print Settings
 Depending on the printer, the cropped image area may not be printed as
you specified.
 The smaller you make the cropping frame, the grainier the picture will
look in the print.
Handling Printer Errors
If printing does not resume after you resolve a printer error (no ink, no paper,
etc.) and select [Continue], operate the buttons on the printer to resume
printing. For details on resuming printing, refer to the printer’s instruction
manual.
Error Messages
If a problem occurs during printing, an error message will appear on the
camera’s LCD monitor. Press <0> to stop printing. After fixing the
problem, resume printing. For details on how to fix a printing problem, refer
to the printer’s instruction manual.
Paper Error
Check whether the paper is properly loaded in the printer.
Ink Error
Check the printer’s ink level and the waste ink tank.
Hardware Error
Check for any printer problems other than paper and ink problems.
File Error
The selected image cannot be printed. Images taken with a different
camera or images edited with a computer may not be printable.
112
11
Transferring Images to
an FTP Server
With image transfer to FTP server, you can
automatically transfer images to the FTP server as you
shoot or transfer a set of shots together after shooting.
113
Transferring Images Individually
Automatic Image Transfer after Each Shot
An image can be automatically transferred to the FTP server
immediately after shooting. You can also continue still photo shooting
as normal even while images are being transferred.
 Before shooting, be sure to insert a card into the camera. If you
shoot without recording images, they cannot be transferred.
 Note that automatic transfer of movies during shooting is not
supported. Transfer the movie after shooting as described on pages
119-123.
1
Select [Communication settings].
 Under the [54] tab, select
[Communication settings], then
press <0>.
2 Select [FTP transfer settings].
114
Transferring Images Individually
[Automatic transfer].
3 Select
 Select [Enable].
the picture.
4 Take
 Connect the camera to an FTP server
in advance (p.75).
 The captured image is transferred to
the FTP server.
 Images cannot be erased during image transfer.
 The following menu items cannot be selected during image transfer.
High ISO speed NR, Dust Delete Data, HDR Mode, Protect images,
Rotate image, Erase images, Print order, Photobook Set-up, Image
copy, Rating, Slide show, Image transfer, Record func+card/folder sel.,
Format card, Sensor cleaning, Communication settings, and Firmware
ver.
 During continuous shooting, images are transferred to the FTP server in
the order they are captured.
 The captured images are also stored on the card.
 Any images for which transfer fails or is interrupted will be transferred
automatically when the connection is recovered (p.118). These images
can also be retransferred in batch at a later time (p.119).
 While connected, the camera’s auto power off does not function.
115
Transferring Images Individually
Transferring the Current Image
Simply play back an image and press <0> to transfer it. You can also
continue still photo shooting as normal even while images are being
transferred.
1
Select [Transfer with SET].
 In step 3 on page 115, select
[Transfer with SET].
 Select [Enable].
the image.
2 Select
 Connect the camera to an FTP server
in advance (p.75).
 Press the <x> button on the
camera.
 Select the image to transfer, then
press <0> to transfer the image.
 Movies cannot be transferred this
way. Selecting a movie and
pressing <0> will display the
movie playback panel.
116
Transferring Images Individually
Selecting Particular Sizes or Types of Images to Transfer
You can select which images to transfer when recording images of
different sizes to a CF card and SD card simultaneously or when
shooting in RAW+JPEG image quality.
1
Select [Transfer type/size].
 In step 3 on page 115, select
[Transfer type/size].
the size and type of images
2 Select
to transfer.
 To transfer smaller JPEGs when the camera is set up to record
larger JPEGs to either a CF card or SD card and smaller JPEGs to
the other, set [JPEG size to trans.] to [SmallerJPEG].
 When the camera is set up to record RAW images to either the CF
card or SD card and JPEGs to the other, specify which images to
transfer in the [RAW+JPEG transfer] setting. Similarly, complete the
same setting when RAW+JPEG images are recorded
simultaneously to a single card.
 When images of the same size are recorded to both a CF card and
SD card simultaneously, images recorded to the card selected for
[Record/play] or [Playback] in [Record func+card/folder sel.]
under the [51] tab are transferred.
117
Transferring Images Individually
Automatic Retransfer if Transfer Fails
If transfer fails, the Wi-Fi function icons on
the LCD panel and LCD monitor blink
(p.23). In this case, press the <M>
button, select [Communication settings]
under the [54] tab, then press <0>. When
the screen shown on the left is displayed,
check the error code number and see page
148 to eliminate the cause of the error.
Once the cause of the error is eliminated, the images whose transfer
previously failed will be retransferred automatically. With this option
activated, transfer is attempted again automatically after a failure, not
only when automatic transfer is used, but also when captured images
are transferred via FTP. Note that when you cancel image transfer, or
turn off the camera, the image will not be retransferred automatically.
See page 119 and transfer the image.
118
Batch Transfer
After shooting, you can select multiple images manually and transfer
them all at once. You can also transfer unsent images or images whose
transfer failed previously.
Note that you can also perform still photo shooting as normal even
while images are being transferred.
 You cannot transfer images during movie shooting.
Selecting the Images to be Transferred
 Selecting Images
1
Select [Image transfer].
 Connect the camera to an FTP server
in advance (p.75).
 Under the [32] tab, select [Image
transfer], then press <0>.
2 Select [Image sel./transfer].
3 Select [Sel.Image].
119
Batch Transfer
images to transfer.
4 Select
 Turn the <5> dial to select the
image to be transferred, then press
<0>.
 Turn the <5> dial to display the [X]
on the screen’s upper left, then press
<0>.
 If you press the <u> button and turn
the <6> dial counterclockwise, you
can select an image from a threeimage display. To return to the singleimage display, turn the dial clockwise.
 To select another image to be
transferred, repeat step 4.
the image.
5 Transfer
 If [FTP transfer] is not displayed,
connect the camera to the FTP server
(p.75).
 Select [FTP transfer], then press
<0>.
 Select [OK] on the confirmation
dialog to transfer the image.
 Images selected with [Sel.n] and
[All images] can also be transferred
in this way.
 If you start movie shooting during image transfer, the image transfer will
be temporarily stopped for the shooting time. When you stop the movie
shooting, the image transfer will resume.
 Images cannot be erased during image transfer.
 The following menu items cannot be selected during image transfer.
High ISO speed NR, Dust Delete Data, HDR Mode, Protect images,
Rotate image, Erase images, Print order, Photobook Set-up, Image
copy, Rating, Slide show, Image transfer, Record func+card/folder sel.,
Format card, Sensor cleaning, Communication settings, and Firmware
ver.
120
Batch Transfer
 You can also transfer shot movies. However, you cannot transfer images
during movie shooting. Set it to <A>, then transfer the images.
 When [Sel.Image] is selected, you can check the transfer history on the
upper left of the screen: No mark: Not selected. X: Selected for transfer.
l: Transfer failed. k: Transfer succeeded.
 The procedures for [RAW+JPEG transfer] (p.122) and above steps 1 to
4 can also be performed even while the camera is not connected to an
FTP server.
 Selecting n
Select [Sel.n] and select [Folder
images not transfer’d]. When you
select a folder, all the images in that
folder not yet transferred to the FTP
server will be selected.
Selecting [Folder images failed transf.] will select the images in the
selected folder that failed to transfer.
Selecting [Clear folder transf. history] will clear the transfer history of
the images in the selected folder. After clearing the transfer history, you
can select [Folder images not transfer’d] and again transfer all the
images in the folder.
 All images
If [All images] is selected and you select
[Card images not transferred], all the
images on the card not yet transferred to
the FTP server will be selected.
For a description of [Card images failed
transfer] and [Clear card’s transf.
history], see “Selecting n” above.
121
Batch Transfer
Transferring RAW+JPEG Images
For RAW+JPEG images, you can specify
which image to transfer.
In step 2 on page 119, select
[RAW+JPEG transfer], and select the
image to be transferred: [JPEG only],
[RAW only], or [RAW+JPEG].
 The [RAW+JPEG transfer] setting
switches in tandem with the
[RAW+JPEG transfer] setting under
[54: Communication settings] 9
[FTP transfer settings] 9 [Transfer
type/size] (p.117).
122
Transferring Images with a Caption
When you select [Transfer with caption], you can add a registered
caption to each image before transfer. This is convenient if you want to
inform the recipient of the printing quantity, for example. The caption is
also added to images stored in the camera.
 You can check captions added to images by examining the user
comments in the Exif information.
 For instructions on creating and registering captions, see page
170.
1
Select [Image transfer].
 Connect the camera to an FTP server
in advance (p.75).
 Under the [32] tab, select [Image
transfer], then press <0>.
[Transfer with caption].
2 Select
 The last image played back is
displayed.
a caption.
3 Set
 Select [Caption] and press <0>,
then select the content of the caption
on the displayed screen.
[Transfer].
4 Select
 The image is transferred with the
caption. When the transfer is
complete, the [Image transfer]
screen will reappear.
It is not possible to manually select images on the [Transfer with caption]
screen. To select another image for transfer with a caption, play back that
image, then follow these steps.
123
Viewing Transferred Images
Images transferred to the FTP server are stored in the following folder
as specified in the FTP server settings.
Target Folders for the FTP Server
 Under the default settings of the FTP server, images or subfolders
containing images are stored in [C drive] 9 [Inetpub] folder 9
[ftproot] folder.
 If the root folder of the transfer destination has been changed in the
FTP server settings, ask the FTP server administrator where images
are transferred.
Folders for Image Storage
Under the default settings, transferred images will be stored in the root
folder specified in the FTP server settings, in a folder structure such as
“A/DCIM/100EOS5D”, which is automatically created.
Note that when a CF card is selected for recording and playback, a
folder structure such as “A/DCIM/100EOS5D” will be automatically
created; when an SD card is selected, the folder structure will be “B/
DCIM/100EOS5D”. (Images will be stored separately, with CF card
images in folder A and SD images in folder B.)
124
Terminating the Connection
On the [rWi-Fi on] screen, select
[Disconnect,exit].
 If the [rWi-Fi on] screen is not
displayed, select in the following
sequence: [54] tab 9
[Communication settings] 9
[Built-in wireless settings] 9
[Wi-Fi function].
 Select [Disconnect,exit], then select
[OK] on the confirmation dialog to
terminate the connection.
125
Changing FTP Server Settings
Change the FTP server settings specified on the camera. To change
the settings, terminate the connection first.
1
Select [Communication settings].
 Under the [54] tab, select
[Communication settings], then
press <0>.
2 Select [Built-in wireless settings].
[Wi-Fi function].
3 Select
 Set [Wi-Fi/NFC] to [Enable], then
select [Wi-Fi function].
[r] (Transfer images to
4 Select
FTP server).
5 Select [Review/change settings].
126
Changing FTP Server Settings
6 Select [Change set.].
[FTP server].
7 Select
 The screen for changing FTP server
settings will appear.
 [Target server]
Change the address and port number
of the destination server.
 [Login password]
Change the login name and login
password.
 [Target folder]
Specify a folder to be used as the
target folder.
 [Directory structure]
Selecting [Camera] automatically creates a folder structure
matching that of the camera’s (such as A/DCIM/100EOS5D) in the
server’s root folder for image storage. If you have created a
subfolder in the root folder by changing the [Target folder] setting, a
folder structure such as “A/DCIM/100EOS5D” is automatically
created in that folder for image storage.
Selecting [Default] will use the root folder for image storage. If you
have created a subfolder in the root folder with the [Target folder]
setting, images are saved in that folder.
127
Changing FTP Server Settings
 [Overwrite same file]
When [Overwrite same file] is set to [Disable]
If there is already a file of the same name in the target folder on the
FTP server, the new file is saved with an extension consisting of an
underscore and a number (example: IMG_0003_1.JPG).
When you resend images if initial transfer fails
With the setting to overwrite the same name file, if you retransfer the
images whose retransfer once failed, the existing file may not be
overwritten in some cases. If this happens, the new file is saved with
an extension consisting of an underscore, a letter, and a number
(example: IMG_0003_a1.JPG).
 [Passive mode]
Enable this setting in network environments protected by a firewall. If
an Error 41 occurs (“Cannot connect to FTP server”), setting passive
mode to [Enable] may enable access to the FTP server.
 [Proxy server]
Change the proxy server settings.
128
12
Sending Images to a
Web Service
You can register various Web services on the camera
and send images stored in the camera to them.
129
Sending Images to a Web Service
You can share images with your family and friends by sending images
from the camera to a Web service registered on the camera or by
sending Web links of the online albums.
Sending Images Individually
Select and send images individually.
1
Select an image to send.
 Turn the <5> dial to select an image
to send, then press <0>.
 By pressing the <u> button and
turning the <6> dial
counterclockwise, you can select an
image from the index display.
[Send img shown].
2 Select
 To select a size at which to send the
image, select [Resize image] and
press <0>.
 Select [Send img shown] and press
<0> to send the image displayed.
 On the screen to complete the
process for sending the image, select
[OK] to terminate the connection and
return to the screen to select a Web
service.
If the camera’s auto power off is activated while connected, the connection
will be terminated. If necessary, set [52: Auto power off] to [Disable].
130
Sending Images to a Web Service
 When the [Terms of use] screen is
displayed, thoroughly read the
message, then select [I Agree].
 The screen can be scrolled up and
down with the <9>.
Sending Multiple Images
Select multiple images and send them at once.
1 Press <0>.
[Send selected].
2 Select
 To select a size at which to send the
images, select [Resize image] and
press <0>.
the images to send.
3 Select
 Turn the <5> dial to select an image
to send, then add [X]. Press <0> to
add or remove [X].
 If you press the <u> button and turn
the <6> dial counterclockwise, you
can select images from a three-image
display.
 After selecting the images to send,
press the <Q> button.
131
Sending Images to a Web Service
[Resize image].
4 Select
 Set it as necessary.
 When YouTube is selected as the
destination, [Resize image] is not
displayed.
 On the displayed screen, select an
image size, then press <0>.
[Send].
5 Select
 The selected images will be sent.
 On the screen to complete the
process for sending the image, select
[OK] to terminate the connection and
return to the screen to select a Web
service.
 When the [Terms of use] screen is
displayed, thoroughly read the
message, then select [I Agree].
 The screen can be scrolled up and
down with the <9>.
132
Sending Images to a Web Service
 While connected to a Web service, a picture cannot be taken even if the
camera’s shutter button is pressed.
 RAW images cannot be sent.
 When sending an image to a Web service other than CANON iMAGE
GATEWAY, a send error message may not be displayed even if the
image was not sent to the Web service successfully. Such errors can be
checked on the CANON iMAGE GATEWAY site; check the error content,
then try sending the image again.
 Depending on the Web service, the number of images that can be sent
and the length of movies will be limited.
 You can select up to 50 files at a time. You can select and send up to 10
files at a time to YouTube.
 When you reduce the image size, all images to be sent at the same time
are resized. Note that movies or still photos that are smaller than b size
are not reduced.
 [Resize:S2] is enabled only for still photos shot with cameras of the
same model as this camera. Still photos shot with other models are sent
without resizing.
 When accessing CANON iMAGE GATEWAY from a computer or other
device, you can check the send history for the Web services that the
images were sent to.
 To terminate the connection without sending an image, press the
<M> button on the screen for step 1.
 When you use a battery to power the camera, make sure it is fully
charged.
133
134
13
Reconnecting and Adding
or Changing Settings
This section explains how to reconnect the camera to
the device for which you set up a connection and how to
register multiple connection settings, check or change
the connection settings, cancel the settings, clear the
wireless function settings to default, etc.
135
Reconnecting
The camera can reconnect to a Wi-Fi function for which connection
settings is already registered.
1
Select [Communication settings].
 Under the [54] tab, select
[Communication settings], then
press <0>.
2 Select [Built-in wireless settings].
[Wi-Fi function].
3 Select
 Set [Wi-Fi/NFC] to [Enable], then
select [Wi-Fi function] (p.20).
the Wi-Fi function to
4 Select
connect to.
 Use <5> or <9> to select an item,
then press <0>.
 When you select [w], a screen to
select a Web service is displayed.
Depending on the selected Web
service, the [Send to] screen is
displayed. Select the Web service to
connect to and the destination.
[Connect].
5 Select
 When settings for multiple connection
destinations are registered, select
[Choose set.], select the connection
destination, then connect to the
destination.
 Select [OK] on the confirmation
dialog.
136
Reconnecting
6
Operate the connected device.
q Smartphone
 Activate the smartphone’s Wi-Fi function, then start Camera
Connect.
 If the smartphone’s connection destination has been changed,
restore the setting to connect to the camera or the same access
point as the camera.
D EOS Utility
 Start EOS Utility on the computer.
 If the computer’s connection destination has been changed,
restore the setting to connect to the camera or the same access
point as the camera.
l Printer
 If the printer’s connection destination has been changed,
restore the setting to connect to the camera or the same access
point as the camera.
r FTP Server
 If the computer’s connection destination has been changed,
restore the setting to connect to the same access point as the
camera.
w Web Service
 The reconnection procedure is complete.
 If you do not know the SSID of the destination when reconnecting, select
[Review/change settings] 9 [Confirm set.] on the screen for step 5 to
check it (p.141).
 With NFC connection or when connecting by selecting [Easy
connection], “_Canon0A” is displayed at the end of the SSID.
137
Registering Multiple Connection Settings
You can register up to three connection settings for each Wi-Fi function.
1
Select [Communication settings].
 Under the [54] tab, select
[Communication settings], then
press <0>.
2 Select [Built-in wireless settings].
[Wi-Fi function].
3 Select
 Set [Wi-Fi/NFC] to [Enable], then
select [Wi-Fi function] (p.20).
the Wi-Fi function to
4 Select
connect to.
 Use <5> or <9> to select an item,
then press <0>.
 When you select [w], a screen to
select a Web service is displayed.
Depending on the selected Web
service, the [Send to] screen is
displayed. Select the Web service to
connect to and the destination.
138
Registering Multiple Connection Settings
5 Select [Choose set.].
[SET* (not configured)].
6 Select
 The connection settings screen is
displayed. Follow the procedures
displayed to complete the connection
settings.
 When connecting to a smartphone, you can register up to three
connection settings in addition to the connection settings added with the
NFC function.
 To delete settings, see page 142.
139
Checking, Changing, or Deleting Connection Settings
Check, change, or delete connection settings saved on the camera. To
change or delete the settings, terminate the connection first.
1
Select [Communication settings].
 Under the [54] tab, select
[Communication settings], then
press <0>.
2 Select [Built-in wireless settings].
[Wi-Fi function].
3 Select
 Set [Wi-Fi/NFC] to [Enable], then
select [Wi-Fi function] (p.20).
the item to check settings
4 Select
for.
 Use <5> or <9> to select an item,
then press <0>.
 When you select an item for which no
setting is saved, the connection
settings screen is displayed.
 When you select [w], a screen to
select a Web service is displayed.
Depending on the selected Web
service, the [Send to] screen is
displayed. The same settings are
displayed for any Web service
selected.
140
Checking, Changing, or Deleting Connection Settings
[Review/change settings].
5 Select
 Select the connection destination on
the [Choose set.] screen, select
[Review/change settings], then
press <0>.
or change the settings.
6 Check
 Select an item and press <0>, then
check or change the settings on the
displayed screen.
[Change set.]
Change the settings. When [Change set.] is selected, a screen for
connection settings configuration appears. Configure connection
settings again following the procedures displayed.
When you select [Transfer images to FTP server] in step 4, a screen
for changing settings appears (p.126). When [Connection wizard] is
selected, a screen for connection settings appears.
[Change settings name]
Change the name of the settings. Select [Change settings name], then
enter the name of the settings using the virtual keyboard (p.18).
[Viewable imgs] (p.94)
Displayed when [q] (Connect to smartphone) is selected. Settings will
appear at the bottom of the screen.
[Confirm set.]
Check the settings. When you select [Confirm set.], the settings will be
displayed.
141
Checking, Changing, or Deleting Connection Settings
Deleting Settings
Select [Delete settings] in step 5 on page 141 to delete connection
settings saved on the camera.
1
Select [Delete settings].
the setting to delete.
2 Select
 Select [OK] on the confirmation
dialog to delete the setting.
During a Connection
When the [Wi-Fi on] screen is displayed
during a wireless connection, select
[Confirm set.] to check the settings.
142
Clearing Built-in Wireless Communication Settings
All built-in wireless communication settings can be deleted. By deleting
the wireless communication settings, you can prevent the information of
the settings from being exposed when you lend or give your camera to
other people.
1
Select [Communication settings].
 Under the [54] tab, select
[Communication settings], then
press <0>.
2 Select [Built-in wireless settings].
[Clear settings].
3 Select
 Set [Wi-Fi/NFC] to [Enable], then
select [Clear settings] and press
<0>.
[OK].
4 Select
 [Built-in wireless settings] are
cleared and the menu screen will
reappear.
Performing [55: Clear all camera settings] does not clear settings for
[Built-in wireless settings] (except [Wi-Fi/NFC] settings).
143
View Info Screen
On the [View info] screen, you can check the error content and the
MAC address.
1
Select [Communication settings].
 Under the [54] tab, select
[Communication settings], then
press <0>.
2 Select [Built-in wireless settings].
[Wi-Fi function].
3 Select
 Set [Wi-Fi/NFC] to [Enable], then
select [Wi-Fi function] (p.20).
the <B> button.
4 Press
 The [View info] screen will appear.
 When an error has occurred, press <0> to display the error
content.
 You can check the MAC address of the camera on this screen.
144
Reference
145
146
14
Troubleshooting Guide
Transfer speed in ad hoc mode may become extremely slow when
the camera is used with certain types of computer. For more
information, contact your dealer or nearest Canon Service Center.
147
Responding to Error Messages
When a connection error occurs, display the details of the error by
following one of the procedures below. Then, eliminate the cause of the
error referring to the examples shown in this chapter.
 On the [View info] screen, press <0> (p.144).
 Select [Error details] on the [Wi-Fi on] screen, then press <0>.
Click the error code number’s page in the following chart to jump to the
corresponding page.
11 (p.149)
12 (p.149)
21 (p.150)
22 (p.151)
23 (p.152)
24 (p.152)
41 (p.154)
42 (p.156)
43 (p.156)
44 (p.156)
45 (p.157)
46 (p.158)
47 (p.158)
61 (p.159)
62 (p.159)
63 (p.160)
64 (p.160)
65 (p.161)
66 (p.161)
67 (p.161)
68 (p.162)
69 (p.162)
121 (p.163)
122 (p.163)
123 (p.163)
124 (p.163)
126 (p.164)
127 (p.164)
141 (p.164)
142 (p.164)
91 (p.162)
125 (p.164)
If [Waiting to retry transfer...] is displayed
If the screen on the left is displayed,
image transfer to an FTP server has
failed. Check the error code number and
eliminate the cause of the error.
Once the cause of the error is eliminated,
the images whose transfer previously
failed will be retransferred automatically.
Note that when you cancel image transfer
or turn off the camera, the image will not
be retransferred automatically. See page
119 and transfer the image.
When an error occurs, [Err**] is displayed on the upper right of the [Wi-Fi
function] screen. It disappears when the camera’s power is set to <2>.
148
Responding to Error Messages
11: Connection target not found
 In the case of [q], is Camera Connect running?
 Establish a connection using Camera Connect (p.36).
 In the case of [l], is the power of the printer on?
 Turn on the printer.
 In the case of [D], is EOS Utility running?
 Start EOS Utility and re-establish the connection (p.46).
 Are the camera and the access point set to use the same
encryption key for authentication?
 This error occurs if the encryption keys do not match when the
authentication method for encryption is set to [Open system].
The setting is case-sensitive, so check upper- and lower-case
characters. Make sure that the correct encryption key for
authentication is entered on the camera (p.71).
12: Connection target not found
 Is the power of the target device and access point on?
 Turn on the target device and access point, then wait a while. If a
connection still cannot be established, perform the procedures to
establish the connection again.
149
Responding to Error Messages
21: No address assigned by DHCP server
What to check on the camera
 On the camera, IP address is set to [Auto setting]. Is this the
correct setting?
 If no DHCP server is used, configure settings after setting the IP
address to [Manual setting] on the camera (p.174).
What to check on the DHCP server
 Is the power of the DHCP server on?
 Turn on the DHCP server.
 Are there enough addresses for assignment by the DHCP
server?
 Increase the number of addresses assigned by the DHCP server.
 Remove devices assigned addresses by the DHCP server from
the network to reduce the number of addresses in use.
 Is the DHCP server working correctly?
 Check the DHCP server settings to make sure it is working
correctly as a DHCP server.
 If applicable, ask your network administrator to ensure the DHCP
server is available.
What to check on the network as a whole
 Does your network include a router or similar device that
serves as a gateway?
 If applicable, ask your network administrator for the network
gateway address and enter it on the camera (p.168, 174).
 Make sure that the gateway address setting is correctly entered on
all network devices including the camera.
150
Responding to Error Messages
22: No response from DNS server
What to check on the camera
 On the camera, does the DNS server’s IP address setting
match the server’s actual address?
 Set the IP address to [Manual setting]. Then, on the camera, set
the IP address that matches the address of the DNS server used
(p.168, 174).
What to check on the DNS server
 Is the power of the DNS server on?
 Turn on the DNS server.
 Are the DNS server settings for IP addresses and the
corresponding names correct?
 On the DNS server, make sure IP addresses and the
corresponding names are entered correctly.
 Is the DNS server working correctly?
 Check the DNS server settings to make sure the server is working
correctly as a DNS server.
 If applicable, ask your network administrator to ensure the DNS
server is available.
What to check on the network as a whole
 Does your network include a router or similar device that
serves as a gateway?
 If applicable, ask your network administrator for the network
gateway address and enter it on the camera (p.168, 174).
 Make sure that the gateway address setting is correctly entered on
all network devices including the camera.
151
Responding to Error Messages
23: Device with same IP address exists on selected
network
What to check on the camera
 Is another device on the camera network using the same IP
address as the camera?
 Change the camera’s IP address to avoid using the same address
as another device on the network. Otherwise, change the IP
address of the device that has a duplicate address.
 If the camera’s IP address is set to [Manual setting] in network
environments using a DHCP server, change the setting to [Auto
setting] (p.72).
24: No response from proxy server
What to check on the camera
 The camera’s proxy server setting is set to [Enable]. Is this the
correct setting?
 If no proxy server is used, set the proxy server setting to [Disable]
(p.77).
 Do the camera’s [Address setting] and [Port No.] settings
match those of the proxy server?
 Configure the camera’s proxy server address and port number to
match those of the proxy server (p.77).
 Are the camera’s proxy server settings correctly entered on
the DNS server?
 Make sure the proxy server’s [Address] is correctly entered on the
DNS server.
152
Responding to Error Messages
What to check on the proxy server
 Is the power of the proxy server on?
 Turn on the proxy server.
 Is the proxy server working correctly?
 Check the proxy server settings to make sure it is working correctly
as a proxy server.
 If applicable, ask your network administrator for the proxy server’s
address setting and port number, then enter them on the camera.
What to check on the network as a whole
 Does your network include a router or similar device that
serves as a gateway?
 If applicable, ask your network administrator for the network
gateway address and enter it on the camera.
 Make sure that the gateway address setting is correctly entered on
all network devices, including the camera.
Responding to Error Messages 21 - 24
Check also the following points when responding to errors numbered 21 24.
Are the camera and the access point set to use the same encryption
key for authentication?
 This error occurs if the encryption keys do not match when the authentication
method for encryption is set to [Open system]. The setting is case-sensitive,
so check upper- and lower-case characters. Make sure that the correct
encryption key for authentication is entered on the camera (p.71).
153
Responding to Error Messages
41: Cannot connect to FTP server
What to check on the camera
 On the camera, does the FTP server’s IP address setting
match the server’s actual address?
 Configure the IP address on the camera to match the actual FTP
server address (p.76).
 Are the camera and the access point set to use the same
encryption key for authentication?
 This error occurs if the encryption keys do not match when the
authentication method for encryption is set to [Open system].
The setting is case-sensitive, so check upper- and lower-case
characters. Make sure that the correct encryption key for
authentication is entered on the camera (p.71).
 On the camera, does the [Port number setting] for the FTP
server match the actual port number of the FTP server?
 Configure the same port number (usually 21) on the camera and
FTP server. Configure the port number on the camera to match the
actual FTP server port number (p.77).
 Are the camera’s FTP server settings correctly entered on the
DNS server?
 Make sure the FTP server’s [Server name] is correctly entered on
the DNS server. Make sure the [Server name] for the FTP server
is correctly entered on the camera (p.76).
154
Responding to Error Messages
What to check on the FTP server
 Is the FTP server working correctly?
 Configure the computer correctly to function as an FTP server.
 If applicable, ask your network administrator for the FTP server
address and port number, then enter them on the camera.
 Is the power of the FTP server on?
 Turn on the FTP server. The server may have been turned off
because of an energy-saving mode.
 On the camera, does the FTP server’s IP address setting (in
[Address]) match the server’s actual address?
 Configure the IP address on the camera to match the actual FTP
server address (p.76).
 Is a firewall or other security software enabled?
 Some security software uses a firewall to restrict access to the FTP
server. Change the firewall settings to allow access to the FTP
server.
 You may be able to access the FTP server by setting [Passive
mode] to [Enable] on the camera (p.128).
 Are you connecting to the FTP server via a broadband router?
 Some broadband routers use a firewall to restrict access to the
FTP server. Change the firewall settings to allow access to the
FTP server.
 You may be able to access the FTP server by setting [Passive
mode] to [Enable] on the camera (p.128).
155
Responding to Error Messages
What to check on the network as a whole
 Does your network include a router or similar device that
serves as a gateway?
 If applicable, ask your network administrator for the network
gateway address and enter it on the camera (p.168, 174).
 Make sure that the gateway address setting is correctly entered on
all network devices including the camera.
42: FTP server rejected connection
What to check on the FTP server
 Is the FTP server configured to restrict access to only some
IP addresses?
 Check the camera’s IP address in [Confirm set.] (p.141), then
change the FTP server settings.
43: Cannot connect to FTP server. Error code received
from server.
What to check on the FTP server
 Have you connected to more FTP servers than the maximum
number of FTP server connections?
 Disconnect some network devices from the FTP server or increase
the maximum number of connections in the FTP server settings.
44: Cannot disconnect FTP server. Error code received
from server.
 This error is displayed if the camera fails to disconnect from
the FTP server for some reason.
 Turn off and on the FTP server and camera.
156
Responding to Error Messages
45: Cannot login to FTP server. Error code received from
server.
What to check on the camera
 On the camera, is the [Login name] entered correctly?
 Check the login name for logging in the FTP server. The setting is
case-sensitive, so check upper- and lower-case characters. Make
sure the correct login name is set on the camera (p.77).
 On the camera, is the [Login password] entered correctly?
 If a login password is configured on the FTP server, check the
upper- and lower-case characters to make sure the correct login
password is set on the camera (p.77).
What to check on the FTP server
 Do the user rights for the FTP server allow reading, writing,
and log access?
 Configure the FTP server’s user rights to allow reading, writing,
and log access.
 Is the folder specified as the transfer destination on the FTP
server named with ASCII characters (p.18)?
 Use ASCII characters to create the folder name.
157
Responding to Error Messages
46: For the data session, error code received from FTP
server
What to check on the FTP server
 The connection was terminated by the FTP server.
 Restart the FTP server.
 Do the user rights for the FTP server allow reading, writing,
and log access?
 Configure the FTP server’s user rights to allow reading, writing,
and log access.
 Do user rights allow access to the target folder on the FTP
server?
 Configure the user rights for access to the target folder on the FTP
server to allow saving images from the camera.
 Is the power of the FTP server on?
 Turn on the FTP server. The server may have been turned off
because of an energy-saving mode.
 Is the hard disk of the FTP server full?
 Increase available space on the hard disk.
47: Image file transfer completion not confirmed by FTP
server
 This error occurs if, for some reason, the transmitter fails to
receive confirmation from the FTP server that image file
transfer is complete.
 Turn off and on the FTP server and camera, then transfer the
images again.
158
Responding to Error Messages
61: Selected SSID wireless LAN network not found
 Are any obstacles blocking the line of sight between the
camera and the antenna of the access point?
 Move the antenna of the access point to a position clearly visible
from the point of view of the camera (p.166).
What to check on the camera
 Does the SSID set on the camera match that of the access
point?
 Check the SSID at the access point, then set the same SSID on
the camera (p.70).
What to check at the access point
 Is the access point turned on?
 Turn on the power of the access point.
 If filtering by MAC address is active, is the MAC address of the
camera used registered at the access point?
 Register the MAC address of the camera used at the access point.
The MAC address can be checked on the [View info] screen
(p.144).
62: No response from wireless LAN terminal
What to check on the camera
 Is the camera configured for communication in infrastructure
mode?
 Configure the camera for communication in ad hoc mode.
What to check on the target device
 Is the target device for ad hoc communication nearby?
 Set up the target device for ad hoc communication near the
camera.
159
Responding to Error Messages
63: Wireless LAN authentication failed
 Are the camera and the access point set to use the same
authentication method?
 The camera supports the following authentication methods: [Open
system], [Shared key], and [WPA/WPA2-PSK] (p.60).
 Are the camera and the access point set to use the same
encryption key for authentication?
 The setting is case-sensitive, so check upper- and lower-case
characters. Make sure that the correct encryption key for
authentication is set on the camera (p.71).
 If filtering by MAC address is active, is the MAC address of the
camera used registered at the access point?
 Register the MAC address of the camera used at the access point.
The MAC address can be checked on the [View info] screen
(p.144).
64: Cannot connect to wireless LAN terminal
 Are the camera and the access point set to use the same
encryption method?
 The camera supports the following encryption methods: WEP,
TKIP, and AES (p.60).
 If filtering by MAC address is active, is the MAC address of the
camera used registered at the access point?
 Register the MAC address of the camera used at the access point.
The MAC address can be checked on the [View info] screen
(p.144).
160
Responding to Error Messages
65: Wireless LAN connection lost
 Are any obstacles blocking the line of sight between the
camera and the antenna of the access point?
 Move the antenna of the access point to a position clearly visible
from the point of view of the camera (p.166).
 The wireless connection was lost for some reason, and the
connection cannot be restored.
 The following are possible reasons: excessive access to the
access point from other device, a microwave oven or similar
appliance in use nearby (interfering with IEEE 802.11b/g/n (2.4
GHz band)), or influence of rain or high humidity (p.166).
66: Incorrect wireless LAN encryption key
 Are the camera and the access point set to use the same
encryption key for authentication?
 The setting is case-sensitive, so check upper- and lower-case
characters. Make sure that the correct encryption key for
authentication is set on the camera (p.71).
67: Incorrect wireless LAN encryption method
 Are the camera and the access point set to use the same
encryption method?
 The camera supports the following encryption methods: WEP,
TKIP, and AES (p.60).
 If filtering by MAC address is active, is the MAC address of the
camera used registered at the access point?
 Register the MAC address of the camera used at the access point.
The MAC address can be checked on the [View info] screen
(p.144).
161
Responding to Error Messages
68: Cannot connect to wireless LAN terminal. Retry from
the beginning.
 Did you hold down the access point’s WPS (Wi-Fi Protected
Setup) button for the specified period of time?
 Hold down the WPS button for the period of time specified in the
access point’s instruction manual.
 Are you trying to establish a connection near the access
point?
 Try establishing the connection when both devices are within reach
of each other.
69: Multiple wireless LAN terminals have been found.
Cannot connect. Retry from the beginning.
 Connection is in progress by other access points in
Pushbutton Connection mode (PBC mode) of Wi-Fi Protected
Setup (WPS).
 Wait a while before trying to establish the connection, or try to
establish a connection in PIN code connection mode (PIN mode)
(p.65).
91: Other error
 A problem other than error code number 11 to 69 occurred.
 Turn off and on the camera’s power switch.
162
Responding to Error Messages
121: Not enough free space on server
 The target Web server does not have enough free space.
 Delete unnecessary images on the Web server, check the free
space on the Web server, then try sending the data again.
122: Connect to a computer, and correct the settings for
the Web service with EOS software.
 Web service setting operation may have failed.
 Connect the camera and computer using an interface cable and
reconfigure Web service settings using EOS Utility (p.57).
123: Cannot log in to Web service. Connect to a computer
and correct the settings with EOS software.
 Is the camera’s registration information or Web service
registered on the camera deleted on CANON iMAGE
GATEWAY?
 Connect the camera and computer using an interface cable and
reconfigure Web service settings using EOS Utility (p.57).
124: Invalid SSL certificate. Connect to a computer and
correct the settings with EOS software.
 The root certificate has expired or is invalid.
 Connect the camera and computer using an interface cable and
reconfigure Web service settings using EOS Utility (p.57).
 This error may be displayed if the camera’s time setting is
significantly off from the actual time. Check if the correct time is set
on the camera.
163
Responding to Error Messages
125: Check the network settings
 Is the network connected?
 Check the connection status of the network.
126: Could not connect to server
 CANON iMAGE GATEWAY is under maintenance or load is
concentrated temporarily.
 Try connecting to the Web service again later.
127: An error has occurred
 A problem other than error 121 to 126 occurred during the
connection to the Web service.
 Try connecting to the Web service again.
141: Printer is busy. Try connecting again.
 Is the printer performing a printing process?
 Connect to the printer again after the printing process is finished.
 Is another camera connected to the printer?
 Connect to the printer again after the connection between the
printer and the other camera has been terminated.
142: Could not acquire printer information. Reconnect to
try again.
 Is the power of the printer on?
 Connect to the printer again after turning on the printer.
164
Troubleshooting Guide
If a problem occurs with the camera, first refer to this Troubleshooting
Guide. If this Troubleshooting Guide does not resolve the problem,
contact the nearest Canon Service Center.
Cannot transfer images to an FTP server.
 To transfer captured images to an FTP server, set the Live View
shooting/Movie shooting switch to <A>. When the Live View
shooting/Movie shooting switch is set to <k>, images cannot be
transferred.
A device connected with an interface cable cannot be used.
 During a wireless LAN connection, you cannot use the camera by
connecting it to Connect Station, a computer, a wireless file
transmitter, or another device with a cable. Terminate the wireless
LAN connection before connecting a cable.
Cannot select [Communication settings].
 When the camera is connected to Connect Station, a computer, a
wireless file transmitter, or another device with an interface cable,
you cannot select [54: Communication settings]. Disconnect the
cable before changing any settings.
Operations such as shooting and playback are not possible.
 Operations such as shooting and playback may not be possible
during a wireless LAN connection. Terminate the connection, then
perform the operation.
Cannot reconnect to a smartphone.
 Even with a combination of the same camera and smartphone, if
you have changed the settings or selected a different setting,
reconnection may not be established even after selecting the same
SSID. In such a case, delete the camera connection settings from
the Wi-Fi settings on the smartphone and set up a connection again.
 If Camera Connect is left running while setting up a connection
again, the connection may not be established. In such a case,
restart Camera Connect.
165
Wireless Function Notes
If the transmission rate drops, the connection is lost, or other problems
occur when using the wireless functions, try the following corrective actions.
Installation Location of Access Point Antenna
 When using indoors, install the device in the room where you are
using the camera.
 Install the device where people or objects do not come between
the device and the camera.
Nearby Electronic Devices
If the transmission rate of a wireless LAN drops because of the
influence of the following electronic devices, stop using them or move
further away from the devices to transmit communication.
 The camera communicates over wireless LANs via IEEE 802.11b/
g/n using radio waves in the 2.4 GHz band. For this reason, the
wireless LAN transmission rate may drop if there are Bluetooth
devices, microwave ovens, cordless telephones, microphones,
smartphones, other cameras, or similar devices operating on the
same frequency band nearby.
Notes for Using Multiple Cameras
 When connecting multiple cameras to one access point, make
sure the cameras’ IP addresses are different.
 When multiple cameras are connected to one access point, the
transmission rate drops.
 When there are multiple IEEE 802.11b/g/n (2.4 GHz band) access
points, leave a gap of four channels between each wireless LAN
channel to reduce radio wave interference. For example, use
channels 1, 6, and 11, channels 2 and 7, or channels 3 and 8.
Using an Eye-Fi Card
 When [Wi-Fi/NFC] is set to [Enable], image transfer using an EyeFi card is disabled.
166
Security
If security settings have not been properly set, the following problems
may occur.
 Transmission monitoring
Third parties with malicious intent may monitor the wireless LAN
transmissions and attempt to acquire the data you are sending.
 Unauthorized network access
Third parties with malicious intent may gain unauthorized access to
the network you are using to steal, modify, or destroy information.
Additionally, you could fall victim to other types of unauthorized
access such as impersonation (where someone assumes an
identity to gain access to unauthorized information) or springboard
attacks (where someone gains unauthorized access to your
network as a springboard to cover their tracks when infiltrating
other systems).
It is recommended to thoroughly secure your network, to prevent these
types of problems from occurring.
167
Checking Network Settings
 Windows
Open the Windows [Command Prompt], then type ipconfig/all and
press the <Enter> key.
The IP address assigned to the computer is displayed and so as the
subnet mask, gateway, and DNS server information.
 Mac OS
In Mac OS X, open the [Terminal] application, enter ifconfig -a, and
press the <Return> key. The IP address assigned to the computer is
indicated in the [en0] item next to [inet], in the format “***.***.***.***”.
* For information about the [Terminal] application, refer to the Mac OS X help.
To avoid using the same IP address for the computer and other devices
on the network, change the rightmost number when configuring the IP
address assigned to the camera in the processes described on page
174.
Example: 192.168.1.10
168
15
Reference
169
Creating and Registering Captions
Follow these steps to create captions and register them on the camera,
as introduced in “Transferring Images with a Caption” (p.123). When
creating and registering captions, use a computer on which EOS Utility
is installed.
See page 43 or 59 to enable the use of EOS Utility over a LAN.
1
Start EOS Utility and select
[Camera settings].
 The camera settings screen is
displayed.
[WFT Captions].
2 Select
 The screen for caption creation is
displayed.
170
Creating and Registering Captions
the caption or captions.
3 Enter
 Enter up to 31 characters (in ASCII
format).
 To acquire caption data stored in the
camera, select [Load settings].
the captions on the
4 Register
camera.
 Select [Apply to camera] to register
your new captions on the camera.
171
Setting up the Network Manually
You can set the network settings for the camera access point mode
manually. [SSID], [Channel setting], and [Encryption settings] can be
set on each screen displayed.
1
Select [Manual connection].
 Select [OK] and press <0> to go to
the next screen.
an SSID (network name).
2 Enter
 Enter any characters using the virtual
keyboard (p.18).
 When you are finished, press the
<M> button.
the desired channel
3 Select
setting.
 To specify the settings manually,
select [Manual setting], then turn the
<6> dial.
 Select [OK] and press <0> to go to
the next screen.
172
Setting up the Network Manually
the desired encryption
4 Select
setting.
 For encryption, select [AES].
 Select [OK] and press <0>.
 When [AES] is selected, the virtual
keyboard (p.18) is displayed. Enter
any encryption key of eight
characters, then press the <M>
button to set.
 The set SSID and encryption key are
displayed.
 For subsequent operations, see
“Easy Connection” (p.27).
173
Setting up the IP Address Manually
Set up the IP address settings manually. The items displayed vary
depending on the selected Wi-Fi function.
1
Select [Manual setting].
 Select [OK] and press <0> to go to
the next screen.
the item to be set.
2 Select
 Select an item and press <0>. The
number entry screen will appear.
 To use a gateway, select [Enable],
select [Address], then press <0>.
the desired values.
3 Enter
 Turn the <6> dial to move the input
position in the upper area and turn
the <5> dial to select the number.
Press <0> to enter the selected
number.
 To set the entered values and return
to the screen for step 2, press the
<M> button.
174
Setting up the IP Address Manually
[OK].
4 Select
 When you have completed setting the
necessary items, select [OK] and
press <0>.
 The setting screen for the Wi-Fi
function will appear.
 If you are not sure what to enter, see
“Checking Network Settings” (p.168),
or ask the network administrator or
another person knowledgeable about
the network.
175
Specifications
9Wireless Communications
Standards compliance: IEEE 802.11b/g/n
Transmission method: DS-SS modulation (IEEE 802.11b)
OFDM modulation (IEEE 802.11g/n)
Transmission range:
Approx. 15 m / 49.2 ft.
* When connected to a smartphone
* With no obstructions between the transmitting and
receiving antennas and no radio interference
Transmission frequency (central frequency):
Connection method:
Security:
NFC connection:
Frequency
Channels
2412 to 2462 MHz
1 to 11 ch
Camera access point mode, infrastructure*, ad hoc mode
* Wi-Fi Protected Setup supported
Authentication method: Open system, Shared key, WPA/
WPA2-PSK
Encryption: WEP, TKIP, AES
For communication with smartphones or connection to
Connect Station
9Wi-Fi Functions
Connection to
smartphones:
Connect to
Connect Station:
Remote operation
using EOS Utility:
Print from Wi-Fi
printers:
Transfer images to
an FTP server:
Send images to
a Web service:
Images can be viewed, controlled, and received using a
smartphone.
Remote control of the camera using a smartphone is
possible.
Images can be sent to a smartphone.
Images can be sent to and saved on Connect Station.
Remote control functions and image viewing functions of
EOS Utility can be used wirelessly.
Images to be printed can be sent to a printer supporting
Wi-Fi.
Automatic transfer, Transfer selected images, Transfer
with SET, and Transfer with caption.
* FTPS supported
Images in the camera or links to images can be sent to
registered Web services.
 All the data above is based on Canon’s testing standards.
176
Trademarks
 Microsoft and Windows are trademarks or registered trademarks of
Microsoft Corporation in the United States and/or other countries.
 Macintosh and Mac OS are trademarks of Apple Inc., registered in the U.S.
and other countries.
 The Wi-Fi CERTIFIED logo and the Wi-Fi Protected Setup mark are
trademarks of the Wi-Fi Alliance.
 WPS used on camera settings screens and in this manual stands for Wi-Fi
Protected Setup.
 UPnP is a trademark of the UPnP Implementers Corporation.
 The N-Mark is a trademark or registered trademark of NFC Forum, Inc. in
the United States and in other countries.
 All other trademarks are the property of their respective owners.
177
Index
A
Access points..................................60
Encryption ..................................60
Android ...........................................26
Automatic image transfer..............114
B
Batch transfer ...............................119
C
Cables.............................................22
Camera access point mode ............74
Camera Connect.......................26, 84
CANON iMAGE GATEWAY ............56
Captions................................123, 170
Clearing wireless
communication settings ................143
I
Image transfer .............................. 113
Individual image transfer .............. 114
iOS ................................................. 26
IP address ............ 63, 67, 72, 76, 174
J
JPEG............................................ 117
K
Keyboard........................................ 18
L
Login method ................................. 77
M
MAC address ......................... 60, 144
N
Communicating with a
smartphone...............................29, 83
NFC.............................. 24, 30, 31, 40
Sending images ......................... 87
Connect Station ..............................39
Nickname ....................................... 16
E
Email...............................................74
Notes............................................ 166
P
EOS Utility ..........................43, 57, 99
PictBridge............................... 49, 103
Eye-Fi Card.....................................22
PIN code connection mode ............ 65
F
Folders....................................78, 124
FTP mode .......................................76
FTP server ......................................75
FTP transfer............................58, 113
FTPS...............................................76
178
Port number ................................... 77
Printer/Printing ....................... 49, 103
Proxy server ................................... 77
Pushbutton connection mode......... 61
Q
Quick Control ................................. 90
Index
R
W
RAW..............................................117
Wi-Fi printer............................ 49, 103
RAW+JPEG ..................................117
WPS (Wi-Fi Protected Setup)......... 60
PBC mode.................................. 61
PIN mode ................................... 65
Reconnecting ................................136
Reducing the image size.........92, 132
Remote operation ...................84, 100
Retransfer .....................................118
S
Select folder ....................................78
Sending images ......................87, 130
Settings .........................................140
Changing ..................................141
Changing names ......................141
Checking...................................141
Deleting ....................................142
Registering ...............................138
Stealth functions .............................60
T
Target folder ............................78, 124
Touch Control..................................19
Transfer after shooting ..................119
Transfer history .............................121
Transfer with SET .........................116
Transferred images .......................124
Troubleshooting ............................147
V
Viewable images.............................95
Viewing images...............................84
179
CANON INC.
30-2 Shimomaruko 3-chome, Ohta-ku, Tokyo 146-8501, Japan
Europe, Africa & Middle East
CANON EUROPA N.V.
PO Box 2262, 1180 EG Amstelveen, The Netherlands
For your local Canon office, please refer to your warranty card or to www.canon-europe.com/Support
The product and associated warranty are provided in European countries by Canon Europa N.V.
CEL-SW7NA210
180
© CANON INC. 2016
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising