LG | 32SE3B-B | User manual | LG 32SE3B-B Panduan User

LG 32SE3B-B Panduan User
USER GUIDE
LG Digital
Signage
(MONITOR SIGNAGE)
Please read this manual carefully before operating your set and retain it for future reference.
L15
www.lg.com
2
ENGLISH
TABLE OF CONTENTS
USING THE MONITOR....................3
-- Using the Input List..........................................................3
-- Adjusting Aspect Ratio...................................................3
ENTERTAINMENT..........................5
-- Using the Network...........................................................5
Connecting to a Network
Network Status
-- Using the My Media.........................................................9
Connecting USB storage devices
Browsing Files
Viewing Movies
Viewing Photos
Listening to Music
Viewing the Contents List
CUSTOMIZING SETTINGS.......... 23
-- Accessing Main Menus................................................23
PICTURE Settings
AUDIO Settings
TIME Settings
OPTION Settings
NETWORK Settings
-- PICTURE ID Settings.....................................................34
IR CODES..................................... 35
TO CONTROL MULTIPLE
PRODUCTS................................... 36
-- Connecting the Cable...................................................36
-- RS-232C Configurations............................................37
4P Cable
RS-232C Cable
-- Communication Parameter.......................................37
-- Command Reference List...........................................38
-- Transmission / Receiving Protocol.........................40
Open Source Software Notice Information
To obtain the source code under GPL, LGPL, MPL, and
other open source licenses, that is contained in this
product, please visit
http://opensource.lge.com.
In addition to the source code, all referred license terms,
warranty disclaimers and copyright notices are available
for download.
LG Electronics will also provide open source code to
you on CD-ROM for a charge covering the cost of
performing such distribution (such as the cost of
media, shipping, and handling) upon email request to
opensource@lge.com.
This offer is valid for a period of three years after our
last shipment of this product. This offer is valid to
anyone in receipt of this information.
3
ENGLISH
USING THE MONITOR
Using the Input List
1 Press
to access the Input List.
2 Press the navigation buttons to scroll to one of the input mode and press
-- RGB-PC
-- HDMI
-- HDMI2
-- DVI-D
-- USB
-- Display Port
-- OPS
.
NOTE
•• Some input signals may not be supported depending on the model.
Adjusting Aspect Ratio
Resize the image to view the image at its optimal size by pressing ARC while you are watching monitor set.
MODE
Aspect
Ratio
16:9
Just Scan
Set By
Program
4:3
Zoom
Cinema
Zoom1
RGB
HDMI
PC
DTV
DVI-D
PC
DTV
Display Port
PC
DTV
OPS
PC
DTV
PC
o
x
o
o
o
x
o
o
o
x
o
o
o
x
o
o
o
x
x
o
x
o
x
o
x
o
x
o
x
o
o
o
x
o
o
o
x
o
o
o
x
o
o
o
x
x
o
x
o
x
o
x
o
x
NOTE
•• You can also change the image size by accessing the main menus.
•• The Just Scan mode operates when a video signal has resolution of 720p or higher.
4
CAUTION
ENGLISH
•• If a fixed image displays on the screen for a long period of time, it will be imprinted and become a permanent
disfigurement on the screen. This is image burn or burn-in and not covered by the warranty.
•• If you don’t use your monitor, turn the power off or set a screen saver program from the PC or the system to prevent
image retention.
•• If the aspect ratio is set to 4:3 for a long period of time, image burn may occur on the letterboxed area of the screen.
•• 16:9 : This selection will allow you to adjust the picture horizontally, in linear proportion, to fill the entire screen
(useful for viewing 4:3 formatted DVDs).
•• Just Scan : This Selection will allow you view the picture of best quality without loss of original picture in high
resolution image. Note: If there is noise in original Picture, You can see the noise at the edge.
•• Set By Program : Depending on the input signal, screen aspect ratio changes to 4:3 or 16:9.
•• 4:3 : This selection will allow you to view a picture with an original 4:3 aspect ratio, black bars will appear on both the
left and right of the screen.
•• Zoom : This selection will allow you to view the picture without any alteration, while filling the entire screen. However,
the top and bottom of the picture will be cropped.
•• Cinema Zoom1 : C
hoose Cinema Zoom when you want to enlarge the picture in correct proportion. Note: When
enlarging or reducing the picture, the image may become distorted.
5
ENGLISH
ENTERTAINMENT
Using the Network
Connecting to a Network
For wired network connections, connect the display to a local area network (LAN) via the LAN port as shown on the
following diagram. Then, set up the network settings. For wireless network connections, connect the Wi-Fi USB module
to the USB port. Then, set up the network settings.
After making a physical connection, a small number of home networks may require the display network settings to be
adjusted. For most home networks, the display will connect to automatically without any adjustments.
For detail information, contact your internet provider or router manual.
LAN
Router
@
Internet
LAN
WAN
ETHERNET
Cable modem
CAUTION
•• Do not connect a modular phone cable to the LAN port.
•• Since there are various connection methods, please follow the specifications of your telecommunication carrier or
internet service provider.
6
ENGLISH
To set up the network settings: (Even if your display has already connected automatically, running setup again will not
harm anything),
Connecting to a wired network
1
2
3
4
Press
to access the main menus.
Press the navigation buttons to scroll to NETWORK and press .
Press the navigation buttons to select Network Setting and press .
If you already set network setting, select Resetting. The new connection settings resets the current network
settings.
5 Select IP Auto Setting or IP Manual Setting.
-- IP Manual Setting
press the navigation and number buttons. IP addresses will need to be input manually.
-- IP Auto Setting
Select this if there is a DHCP server (Router) on the local area network (LAN) via wired connection, the display
will automatically be allocated an IP address. If you’re using a broadband router or broadband modem that has a
DHCP (Dynamic Host Configuration Protocol) server function. The IP address will automatically be determined.
6 When you are finished, press
.
Connecting to a wireless network
1
2
3
4
Press
to access the main menus.
Press the navigation buttons to scroll to NETWORK and press .
Press the navigation buttons to select Network Setting and press .
Select Setting from the AP list or Simple setting (WPS-button mode).
-- Setting from the AP list
Select an AP to connect to a wireless network.
-- Simple setting (WPS-button mode)
Press the button on the wireless router that supports PBC to easily connect to the router.
5 When you are finished, press
.
CAUTION
•• Network setting menu will not be available until the display connected to physical network.
•• Since there are various connection methods, please follow the specifications of your telecommunication carrier or
internet service provider.
•• When a Wi-Fi dongle is used with a model that has only one USB input port, the distribution or content schedule via
the SuperSign software is not available.
NOTE
•• If you want to access the Internet directly on your display, the Internet connection should always be on.
•• If you cannot access the Internet, check the network conditions from a PC on your network.
•• When you use Network Setting, check the LAN cable or check if DHCP in the router is turned on.
•• If you do not complete the network settings, the network may not work properly.
•• When connected to a network that supports IPv6, you can select IPv4/IPv6 in the advanced wired/wireless network
setting. But, IPv6 connection only supports automatic connection.
7
Tips for Network setting
Tips for Wireless Network Setting
•• Wireless networks can be subject to interference from other devices operating at a frequency of 2.4 GHz (wireless
phones, Bluetooth devices, or microwave ovens). There may also be interference from devices with a frequency of 5
GHz, same as other Wi-Fi devices.
•• The surrounding wireless environment can cause the wireless network service to run slowly.
•• For an AP connection, an access point device that supports wireless connection is required and the wireless
connection feature must be enabled on the device. Contact your service provider regarding availability of wireless
connection on your access point.
•• Check the SSID and security settings of the AP for AP connection. Refer to the appropriate documentation for SSID
and security settings of the AP.
•• Invalid settings on network devices (wired/wireless line sharer, hub) can cause the monitor to run slowly or not
operate properly. Install the devices correctly according to the appropriate manual and set the network.
•• Connection method may differ according to the AP manufacturer.
ENGLISH
•• Use a standard LAN cable with this display. Cat5 or better with a RJ45 connector.
•• Many network connection problems during set up can often be fixed by re-setting the router or modem. After
connecting the display to the home network, quickly power off and/or disconnect the power cable of the home
network router or cable modem. Then power on and/or connect the power cable again.
•• Depending on the internet service provider (ISP), the number of devices that can receive internet service may be
limited by the applicable terms of service. For details, contact your ISP.
•• LG is not responsible for any malfunction of the display and/or the internet connection feature due to communication
errors/malfunctions associated with your internet connection, or other connected equipment.
•• LG is not responsible for problems within your internet connection.
•• You may experience undesired results if the network connection speed does not meet the requirements of the
content being accessed.
•• Some internet connection operations may not be possible due to certain restrictions set by the Internet service
provider (ISP) supplying your Internet connection.
•• Any fees charged by an ISP including, without limitation, connection charges are your responsibility.
•• A 10 Base-T or 100 Base-TX LAN port is required when using a wired connection to this display. If your internet
service does not allow for such a connection, you will not be able to connect the display.
•• A DSL modem is required to use DSL service and a cable modem is required to use cable modem service. Depending
on the access method of and subscriber agreement with your ISP, you may not be able to use the internet connection
feature contained in this display or you may be limited to the number of devices you can connect at the same
time. (If your ISP limits subscription to one device, this display may not be allowed to connect when a PC is already
connected.)
•• The use of a router may not be allowed or its usage may be limited depending on the policies and restrictions of your
ISP. For details, contact your ISP directly.
8
Network Status
ENGLISH
1
2
3
4
5
Press
to access the main menus.
Press the navigation buttons to scroll to NETWORK and press
Press the navigation buttons to select Network Status.
Press
to check the network status.
When you are finished, press
.
Option
Setting
Test
Close
.
Description
Return to the network setting menu.
Test the current network status after setting the network.
Return to the previous menu.
9
Connecting USB storage devices
Connect USB storage devices such as a USB flash memory, external hard drive to the display and use multimedia
features.
Connect a USB flash memory or USB memory card reader to the Display as shown on the following illustration.
The My Media screen appears.
OR
CAUTION
•• Do not turn the display off or remove a USB storage device while MY MEDIA menu is activated, as this could result
in loss of files or damage to the USB storage device.
•• Back up your files saved on a USB storage device frequently, as you may lose or damage the files and this may be not
covered by the warranty.
ENGLISH
Using the My Media
10
Tips for using USB storage devices
ENGLISH
•• Only a USB storage device is recognizable.
•• If the USB storage device is connected through a USB hub, the device is not recognizable.
•• A USB storage device using an automatic recognition program may not be recognized.
•• A USB storage device which uses its own driver will not be recognized.
•• The recognition speed of a USB storage device may depend on each device.
•• Please do not turn off the display or unplug the USB device when the connected USB storage device is working.
When such a device is suddenly separated or unplugged, the stored files or the USB storage device may be damaged.
•• Please do not connect the USB storage device which was artificially maneuvered on the PC. The device may cause the
product to malfunction. Only use a USB storage device which has normal music files, image files or movie files.
•• Please only use USB storage devices formatted using the FAT32 file system. Storage devices formatted with utility
programs that are not supported by Windows may not be recognized.
•• Please connect power to a USB storage device (over 0.5 A) which requires an external power supply. If not, the device
may not be recognized.
•• Please connect a USB storage device with the cable included by the device maker.
•• Some USB storage devices may not be supported or operate smoothly.
•• File alignment method of USB storage devices is similar to Window XP and the monitor can recognize up to 100
English characters.
•• Be sure to back up important files since data stored on a USB memory device may be damaged. We will not be
responsible for any data loss.
•• If the USB HDD does not have an external power source, the USB device may not be detected. So be sure to connect
the external power source.
- Please use a power adaptor for an external power source.
•• If your USB memory device has multiple partitions, or if you use a USB multi-card reader, you can use up to 4
partitions or USB memory devices.
•• If a USB memory device is connected to a USB multi-card reader, its volume data may not be detected.
•• If the USB memory device does not work properly, disconnect and reconnect it.
•• How fast a USB memory device is detected differs from device to device.
•• If the USB is connected in Standby Mode, that drive will automatically be loaded when the display is turned on.
•• The recommended capacity is 1 TB or less for a USB external hard disk and 32 GB or less for USB memory.
•• Any device with more than the recommended capacity may not work properly.
•• If a USB external hard disk with an Energy Saving function does not work, turn the hard disk off and on again to make
it work properly.
•• USB storage devices below USB 2.0 are supported as well. But they may not work properly with videos.
•• A maximum of 999 folders or files can be recognized under one folder.
•• A USB 3.0 storage device may not work.
•• Data on some USB storage devices may be damaged in a high temperature environment.
•• It is recommended that you avoid playing contents using more than two USB ports simultaneously.
11
Browsing Files
1 Press
to access the main menu.
2 Press the search button to scroll to
and press .
3 Press the Search button to go to the Movie List, Photo List, Music List, or Content List that you want, and press
.
Supported file format
Type
Supported file format
Movie
Video
Audio
Codec
Media Container
Profile
MPEG1 / MPEG2
DAT, MPG, MPEG,
TS, TP
1080P @ 30 fps
MPEG4
(DivX 3.11, DivX 4,
DivX 5, DivX 6,
Xvid 1.01, Xvid 1.02, Xvid
1.03, Xvid 1.10-beta1/2)
AVI, DIVX, MP4,
MKV, TS, TRP
1080P @ 30 fps
H.264
AVI, MP4, MKV, TS,
TRP, TP
1080P @ 60 fps
MP3
MP3
8 kbps - 320 kbps(Bit rate)
16 kHz - 48 kHz(Sample rate)
AC3
AC3
32 kbps - 640 kbps(Bit rate)
32 kHz, 44.1 kHz, 48 kHz(Sample
rate)
MPEG
MP3
32 kbps - 448 kbps(Bit rate)
16 kHz - 48 kHz(Sample rate)
AAC, HEAAC
MP4
8 kHz - 48 kHz(Sample rate)
LPCM
AVI, WAV
64 kbps - 1.5 Mbps(Bit rate)
8 kHz - 48 kHz(Sample rate)
Bit rate : within 8 kbps to 320 kbps(MP3)
External Subtitle format : *.smi/*.srt/*.sub(MicroDVD, Subviewer1.0/2.0)/*.ass/*.ssa/*.txt(TMPlayer)/
*.psb(PowerDivX)
Internal Subtitle format : only, XSUB (It is the subtitle format used in DivX6 files)
ENGLISH
Browse files saved in a USB storage device.
12
Type
ENGLISH
Photo
Supported file format
Min : 64 x 64
Max : Normal Type: 15360 (W) x 8640 (H)
Progressive Type: 1920 (W) x 1440 (H)
BMP
Min : 64 x 64
Max : 9600 x 6400
PNG
Min : 64 x 64
Max : Interlace: 1200 x 800
Non-Interlace: 9600 x 6400
•• Non-supported files are displayed in the form of predefined icon.
Music
mp3
[Bit rate] 32 kbps ~ 320 kbps
[Sample freq] 16 kHz ~ 48 kHz
[Support] MPEG1, MPEG2, Layer2, Layer3
AAC
[Bit rate] Free Format
[Sample freq.] 8 kHz ~ 48 kHz
[Support] ADIF, ADTS
M4A
[Bit rate] Free Format
[Sample freq.] 8 kHz ~ 48 kHz
[Support] MPEG-4
OGG
[Bit rate] Free Format
[Sample freq.] ~ 48 kHz
[Support] Vorbis
WMA
[Bit rate] 128 kbps ~ 320 kbps
[Sample freq.] 8 kHz ~ 48 kHz
[Support] WMA7, 8, 9 Standard
WMA 10 Pro
[Bit rate] ~768 kbps
[Channel / Sample freq.]
M0 : Up to 2 / 48 kHz
M1 : Up to 5.1 / 48 kHz
M2 : Up to 5.1 / 96 kHz
[Support] WMA 10 Pro
13
File Extensions : *.cts/ *.sce
Movie
File Extensions: *.mpg/*.mpeg/*.dat/*.ts/*.trp/*.tp/*.mp4/*.mkv/*.avi/*. avi(motion JPEG)/*.
mp4(motion JPEG)/*.mkv(motion JPEG)
Video format: MPEG1, MPEG2, MPEG4,H.264, DivX 3.11, DivX 4, DivX 5, DivX 6,
Xvid 1.00,Xvid 1.01, Xvid 1.02, Xvid 1.03,Xvid 1.10-beta1/2, JPEG
Audio format: MP3, Dolby Digital, LPCM, AAC, HE-AAC
Viewing Movies
Plays movie files saved in the USB storage device.
1
2
3
4
5
Press
to access the main menu.
Press the navigation button to scroll to MY MEDIA and press .
Press the navigation button to scroll to Movie List and press .
Press the navigation buttons to scroll to a folder you want and press .
Press the navigation buttons to scroll to a file you want and press .
-- Change Device : Selects the USB storage device. (Depending on model)
-- Go to root folder : Returns to the home screen of My Media.
-- Go to upper folder : Returns to the previous screen.
-- Exit : Exits My Media.
6 During movie playback, press
to access the following settings.
Remote
button
Description
Stops the playback.
Plays a video.
Pauses or resumes the playback.
Scans backward in a file.
Scans forward in a file.
Adjusts the screen brightness to save energy.
Show the Option menu.
Hide the menu on the full-sized screen.
Returns to Movie List.
OR
Skips to specific points in a file during playback. The time of a specific point will appear on the
status bar. In some files, this function may not work properly.
ENGLISH
Content (when
using SuperSign
software)
14
Tips for using playing video files
ENGLISH
•• Some user-created subtitles may not work properly.
•• Some special characters are not supported in subtitles.
•• HTML tags are not supported in subtitles.
•• Subtitles in languages other than the supported languages are not available.
•• The screen may suffer temporary interruptions (image stoppage, faster playback, etc.) when the audio language is
changed.
•• A damaged movie file may not be played correctly, or some player functions may not be usable.
•• Movie files produced with some encoders may not be played correctly.
•• If the video and audio structure of recorded file is not interleaved, either video or audio is outputted.
•• HD videos with a maximum of 1920 x 1080 @ 25/30p or 1280 x 720 @ 50/60p are supported, depending on the
frame.
•• Videos with resolutions higher than 1920 x 1080 @ 25/30p or 1280 x 720 @ 50/60p may not work properly
depending on the frame.
•• Movie files other than the specified types and formats may not work properly.
•• Max bitrate of playable movie file is 20 Mbps. (only, Motion JPEG : 10 Mbps)
•• We do not guarantee smooth playback of profiles encoded level 4.1 or higher in H.264/AVC.
•• DTS Audio codec is not supported.
•• A movie file more than 30 GB in file size is not supported for playback.
•• A DivX movie file and its subtitle file must be located in the same folder.
•• A video file name and its subtitle file name must be identical for it to be displayed.
•• Playing a video via a USB connection that doesn’t support high speed may not work properly.
•• Files encoded with GMC(Global Motion Compensation) may not be played.
Video options
1 Press
to access the Pop-Up menus.
2 Press the navigation buttons to scroll to Set Video Play, Set Video, or Set Audio, and press
.
NOTE
•• The option values changed in Movie List do not affect Photo List or Music List. Therefore, they are not affected by
option values changed in Photo List or Music List.
•• The option values changed in Photo List and Music List do affect each other.
•• When replaying the video file after stopping, you can play from where it stopped previously.
15
Select Set Video Play to access the following menus:
Subtitle
Language
Language
Code Page
Sync
Position
Size
Repeat
Description
Selects your desired picture format during movie play.
Changes the Language Group of the audio during movie play. Files with a single audio track
cannot be selected.
Turn on/off the subtitle.
Activated for SMI subtitle and can select the language within the subtitle.
Can select the font for subtitle.
When set to default, same font as general menu will be used.
Adjusts the time synchronization of the subtitle from -10 secs to +10 secs by steps of 0.5 secs
during movie play.
Changes the position of the subtitle either up or down during movie play.
Selects your desired Subtitle size during movie play.
Turn on/off repeat function of movie playback. When turned on, the file within the folder will be
played back repeatedly. Even when the repeated playback is turned off, it can run the playback if
the file name is similar to the previous file.
NOTE
•• Only 10,000 of sync blocks can be supported within the subtitle file.
•• When playing a video, you can adjust the picture size by pressing the ARC button.
•• Subtitles in your language are only supported when the OSD menu is also in this language.
•• The code page options may be disabled depending on the language of the subtitle files.
•• Select the appropriate code page for the subtitle files.
ENGLISH
Menu
Picture Size
Audio Language
16
Viewing Photos
ENGLISH
View image files saved in the USB storage device.
1
2
3
4
5
Press
to access the main menu.
Press the navigation button to scroll to MY MEDIA and press .
Press the navigation button to scroll to Photo List and press .
Press the navigation buttons to scroll to a folder you want and press .
Press the navigation buttons to scroll to a file you want and press .
-- Change Device : Selects the USB storage device. (Depending on model)
-- Go to root folder : Returns to the home screen of My Media.
-- Go to upper folder : Returns to the previous screen.
-- Exit : Exits My Media.
6 While viewing photos, you can access the following settings.
Menu
Slideshow
BGM
Description
Starts or stops a slideshow with selected photos. If there are no selected photos, all photos saved
in the current folder display during a slideshow. To set a slideshow speed, select Option.
Turns the background music on or off. To set the background music folder, select Option.
You can adjust option by
button on the remote control.
Rotates photos clockwise (90 °, 180 °, 270 °, 360 °).
NOTE
•• The supported photo size is limited. You cannot rotate a photo if the resolution of the rotated
width is larger than the supported resolution size.
Enlarges the photo by 100 %, 200 % or 400 %.
Adjusts the brightness of the screen for energy saving.
Option
Hide
Exit
To display the options.
Hides the option window.
Return to Photo List.
17
Photo options
.
NOTE
•• The option values changed in Movie List do not affect Photo List or Music List. Therefore, they are not affected by
option values changed in Photo List or Music List.
•• The option values changed in Photo List and Music List do affect each other. Select Setting Photo View to access
the following menus:
Menu
Description
Slide Speed
Select a slideshow speed.
(Options: Fast, Medium, or Slow.)
BGM
Selects a music folder for the background music.
Repeat
Plays background music on repeat.
Random
Plays background music in random order.
ENGLISH
1 Press
to show the Option menus.
2 Press the navigation buttons to scroll to Set Photo View, Set Video, or Set Audio, and press
18
Listening to Music
ENGLISH
Plays music files saved in the USB storage device.
1
2
3
4
5
Press
to access the main menu.
Press the navigation button to scroll to MY MEDIA and press .
Press the navigation button to scroll to Music List and press .
Press the navigation buttons to scroll to a folder you want and press .
Press the navigation buttons to scroll to a file you want and press .
-- Change Device : Selects the USB storage device. (Depending on model)
-- Go to root folder : Returns to the home screen of My Media.
-- Open Music Player : Opens the settings window for music. This feature is activated only during playback.
-- Go to upper folder : Returns to the previous screen.
-- Exit : Exits My Media.
6 During music playback, press
to access the following settings.
Remote
button
Description
Stops playing back the file and moves back to the Music List.
Plays a music file.
Pauses or resumes playback.
Skips to the previous file. The previous track of the current music is played. If there is no previous
track, the music currently playing will be played from the beginning.
Skips to the next file.
Adjusts the brightness of the screen for energy saving (Off and Screen Off work only.)
Show the Option menu.
Hides the option window.
OR
Return to Music List.
Skips to specific points in a file during playback. The time of a specific point will appear on the
status bar. In some files, this function may not work properly.
Tips for playing music files
•• This unit cannot support the ID3 Tag embedded MP3 files.
NOTE
•• A damaged or corrupted music file does not play but displays 00:00 in playtime.
•• A music downloaded from a paid service with copyright protection does not start but displays inappropriate
information in playtime.
•• If you press ,
buttons, screen saver is stopped.
•• The
,
,
,
,
buttons on the remote control are also available in this mode.
•• You can use the
button to select the next music and the
button to select the previous music.
19
file name
ENGLISH
HR1.mp3
01:40 / 03:03
Time elapsed/ Duration
Music options
1 Press
to access the pop-up menus.
2 Press the navigation buttons to scroll to Set Audio Play or Set Audio and press
.
NOTE
•• The option values changed in Movie List do not affect Photo List or Music List. Therefore, they are not affected by
option values changed in Photo List or Music List.
•• The option values changed in Photo List and Music List do affect each other.
When you select the Set Audio Play,
Menu
Repeat
Random
Description
Repeats the music playback.
Plays random music tracks.
20
Viewing the Contents List
ENGLISH
You can play the files saved using the Export function to an external file in the SuperSign Software.
1
2
3
4
5
Press
to access the main menu.
Press the navigation button to scroll to MY MEDIA and press .
Press the navigation button to scroll to Contents List and press .
Press the navigation buttons to scroll to a folder you want and press .
Press the navigation buttons to scroll to a file you want and press .
-- Change Device : Selects the USB storage device. (Depending on model)
-- Go to root folder : Returns to the home screen of My Media.
-- Go to upper folder : Returns to the previous screen.
-- Exit : Exits My Media.
NOTE
•• While playing media files from Contents List, only the
,
, or volume button are available. Selecting the
or
button stops playing media files and returns to the Contents List.
•• When you use the distribution feature which utilizes SuperSign Software, the storage device used to store contents
is determined based on the size of the remaining memory space. (Note: If USB ports 1 and 2 have the same memory
space, contents will be saved on the storage device connected to USB port 1.(Depending on model))
•• If there is the AutoPlay folder in the USB device and its files are in supported formats, they can be played back
automatically when the USB device is connected to the monitor.
•• It is recommended that you avoid playing contents using more than two USB ports simultaneously.
•• With respect to the playback of distribution or contents schedules through SuperSign Software, the schedule
executed last time is played.
21
Supported Video Codec
Codec
.asf
.wmv
Videos
VC-1 Simple and Main Profiles
Audio
WMA Standard, WMA 10 Professional
.divx
.avi
Videos
DivX3.11, DivX4, DivX5, DivX6, XViD, H.264/AVC, Motion Jpeg, MPEG-4 Part2
Audio
MPEG-1 Layer I, II, MPEG-1 Layer III (MP3), Dolby Digital, LPCM, ADPCM, DTS
.mp4
.m4v
.mov
Videos
H.264/AVC, MPEG-4 Part2
Audio
AAC, MPEG-1 Layer III (MP3)
.3gp
.3g2
Videos
H.264/AVC, MPEG-4 Part2
Audio
AAC, AMR-NB, AMR-WB
.mkv
Videos
H.264/AVC
Audio
HE-AAC, Dolby Digital
.ts
.trp
.tp
.mts
.m2ts
Videos
H.264/AVC, MPEG-2
Audio
MPEG-1 Layer I, II, MPEG-1 Layer III (MP3), Dolby Digital, Dolby Digital Plus,
AAC, PCM
.mpg
.mpeg
Videos
MPEG-1, MPEG-2
Audio
MPEG-1 Layer I, II, MPEG-1 Layer III (MP3), AAC
.vob
Videos
MPEG-1, MPEG-2
Audio
Dolby Digital, MPEG-1 Layer I, II, DVD-LPCM
ENGLISH
Extension
22
Tips for Playing Video Files
ENGLISH
•• A damaged movie file may not play correctly, or some player features may not be usable.
•• Movie files produced with some encoders may not be played correctly.
•• Movie files other than the specified types and formats may not work properly.
•• Max bit rate of playable movie file is 20 Mbps. (For Motion JPEG: 10 Mbps only)
•• We do not guarantee smooth playback of profiles encoded level 4.1 or higher in H.264 / AVC.
•• Video files larger than 50 MB may not upload properly from mobile devices. We recommend that you play such files
via USB/SD storage devices.
•• [For Ultra HD models only] Ultra HD image: 3840 X 2160
Some HEVC-encoded Ultra HD videos other than the content officially provided by LG Electronics may not be played.
Extension
.mkv
.mp4
.ts
Codec
Video
H.264/AVC, HEVC
Audio
Dolby Digital, Dolby Digital Plus, AAC, HE-AAC
•• Some codecs can be used after upgrading software.
23
Accessing Main Menus
1
2
3
4
Press
to access the main menus.
Press the navigation buttons to scroll to one of the following menus and press .
Press the navigation buttons to scroll to the setting or option you want and press .
When you are finished, press
. When you return to the previous menu, press
.
-- PICTURE : Adjusts the image size, quality, or effect.
-- AUDIO : Adjusts the sound quality, effect, or volume level.
-- TIME : Sets the time, date, or timer feature.
-- OPTION : Customizes the general settings.
-- NETWORK : Sets up the network setting.
-- MY MEDIA : D
isplay and play movie, photo and music contents stored on your USB or signage device (Internal
storage device).
ENGLISH
CUSTOMIZING SETTINGS
24
PICTURE Settings
ENGLISH
1 Press
to access the main menus.
2 Press the navigation buttons to scroll to PICTURE and press .
3 Press the navigation buttons to scroll to the setting or option you want and press
-- To return to the previous level, press
4 When you are finished, press
.
.
When you return to the previous menu, press
.
.
The available picture settings are described in the following:
Setting
Energy
Saving
Description
reduces power consumption by adjusting peak screen brightness.
Level
Off
Disables Energy Saving function.
Minimum/Medium/ Selects the brightness level of the backlight.
Maximum
Screen Off
The screen turns off in 3 seconds.
Smart Energy Adjusts the backlight and contrast depending on the screen brightness.
Saving
Level
Off
Disables the Smart Energy Saving function.
On
Picture Mode
Enables the Smart Energy Saving function to save power consumption as
much as the value set in the smart energy saving rate.
Selects the picture mode optimized for the viewing environment or the program.
Mode
Vivid
Heightens contrast, brightness, and sharpness to display vivid images.
Standard
APS
Game
Displays images in standard levels of contrast, brightness, and sharpness.
APS ( Auto power saving ) mode reduces power consumption by dimming
control.
Optimizes the video image for a cinematic look to enjoy movies as if you are
in a movie theater.
Optimizes the video image for high and dynamic actions by emphasizing
primary Colors such as white, grass, or sky blue.
Optimizes the video image for a fast gaming screen such as PCs or games.
Calibration
Applies user-customized white balance based on Standard.
Cinema
Sport
Expert1·2
Aspect Ratio
Menu for adjusting picture quality that allows experts and amateurs to enjoy
the best Monitor viewing.
Changes the image size to view images at its optimal size.
25
Setting
Description
Customizes the PC display options in RGB mode.
Option
(In RGB Mode
Only)
Resolution
Selects a proper resolution.
Auto Configure
Sets to adjust the screen position, clock, and phase automatically.
The displayed image may be unstable for a few seconds while the
configuration is in progress.
Adjusts the options when the picture is not clear, especially when
characters are shaky, after the auto configuration.
Restores the options to the default setting.
Position/Size/
Phase
Reset
Basic image options
Setting
Description
Color
djusts the brightness of the screen by controlling the LCD backlight. If you decrease the
A
brightness level, the screen becomes darker and the power consumption will be reduced without
any video signal loss.
Increases or decreases the gradient of the video signal. You may use Contrast when the bright
part of the picture is saturated.
Adjusts the base level of the signal in the picture. You may use Brightness when the dark part of
the picture is saturated.
Adjusts the level of crispness in the edges between the light and dark areas of the picture. The
lower the level, the softer the image.
Adjusts intensity of all colors.
Tint
Adjusts the balance between red and green levels.
Color Temp.
Set to warm to enhance hotter Colors such as red, or set to cool to make picture bluish.
Advanced
Control/
You can adjust the picture for each Picture Mode, or adjust the picture settings according to a
specific picture image. First, select a desired Picture Mode.
* This option is unavailable if Picture Mode is set to Vivid.
Backlight
Contrast
Brightness
Sharpness
Expert Control
Picture Option
Picture Reset
Sets additional picture option.
Restores the options to the default setting.
NOTE
•• When you select a picture mode, related menus are set automatically.
•• When using the Smart Energy Saving function, the screen may look saturated in the white area of a still image.
•• If Energy Saving is set to Minimum, Medium, or Maximum, the Smart Energy Saving function is disabled.
ENGLISH
Screen
26
Advanced Control - Picture Mode (Standard/ APS/ Sport/ Game/ Calibration)
ENGLISH
Setting
Description
Dynamic Contrast
Adjusts the contrast to the optimal level according to the brightness of the image.
Dynamic Color
Adjusts color for more natural-looking colors.
Color Gamut
Selects the range of colors that can be expressed.
Skin Color
Sky Color
Skin color spectrum can be separately set to implement the skin color as defined by the
user.
Sky color is set separately.
Grass Color
Natural color spectrum (meadows, hills, etc.) can be separately set.
Gamma
Sets the gradation curve according to the output of the picture signal in relation to the
input signal.
Expert Control - Picture Mode (Cinema/ Expert1/ Expert2)
Setting
Description
Color Gamut
Adjusts the contrast to the optimal level according to the brightness of the image.
(Function works in the following mode - HDMI-DTV)
Selects the range of colors that can be expressed.
Edge Enhancer
Shows clearer and distinctive yet natural edges of the video.
Color Filter
Filters a specific color spectrum in RGB colors to fine-tune color saturation and hue accurately.
Color
Temperature
Adjusts the overall tone of the screen as desired. In Expert mode, detailed fine-tuning can be set
via Gamma method, etc.
Color
Management
System
This is a system that experts use when they adjust color with a test pattern. They can select from
six color areas (Red / Green / Blue / Cyan / Magenta / Yellow) without affecting other colors. For
normal images, adjustments may not result in noticeable color changes.
Dynamic
Contrast
27
Picture Option - HDMI(DTV) Mode
Description
Reduces screen noise in the video.
MPEG Noise Reduction
Reduces noise caused by compressing digital video.
Black Level
Adjusts the black level of the picture to correct the brightness and contrast of the
picture.(Recommended settings according to input signal: RGB 0–255: High, RGB
16–235: Low, YCbCr: Low)
Optimizes the screen for movie viewing.
Real Cinema
TruMotion (This feature is
supported by 65SE3B and
65SE3KB only.)
Corrects images to display smoother motion sequences.
•• Off : Turn off the TruMotion.
•• Smooth/ Clear : De-Judder / De-Blur can be set Auto.
•• User : De-Judder / De-Blur can be set manually.
-- De-Judder : This function adjusts juddering of the screen.
-- De-Blur : This function adjusts and eliminates blurring of the screen.
TruMotion
• De-Judder
• De-Blur
Smooth
Auto
Auto
OK
ENGLISH
Setting
Noise Reduction
28
AUDIO Settings
ENGLISH
1 Press
to access the main menus.
2 Press the navigation buttons to scroll to
and press .
3 Press the navigation buttons to scroll to the setting or option you want and press
-- To return to the previous level, press
4 When you are finished, press
.
.
When you return to the previous menu, press
.
.
The available audio options are described in the following:
Setting
Sound Mode
Sound Effect
AV Sync. Adjust
Description
Allows optimized sound for custom Monitor installation.
Level
Standard
Suitable for all types of video.
News/ Music/
Sets audio optimized for a specific genre.
Cinema/ Sport/
Game
The user can select various sound effects.
-Sound Effect function is available only for Standard mode in Sound Mode menu.
Level
Clear Voice ll
Boosts voice clarity.
Virtual Surround
LG’s proprietary audio processing technology allows 5.1ch-like surround
sound from two speakers.
- If Clear Voice ll is set to On, Virtual Surround will not be chosen.
Equalizer
Adjusts the volume to a level of your choice using the Equalizer.
Balance
Adjusts left/right audio balance.
Reset
You can reset the settings under the Sound Effects menu.
Synchronizes video and audio directly when they do not match.
If you set AV Sync. to ON, you can adjust the sound output to the screen image.
•• Speaker: Adjusts the synchronization of the sound from the speakers. The “-” button makes
the sound output faster and the “+” button slower than the default value.
•• Bypass : The audio of an external device without audio delay. Audio may be output before
video as it takes time to process video input into the Monitor.
NOTE
•• Some models may not have built-in speakers. In that case, you need to connect external speakers to listen to sound.
29
TIME Settings
-- To return to the previous level, press
.
4 When you are finished, press
.
When you return to the previous menu, press
.
.
The available time settings are described in the following:
Setting
Clock
Description
Sets the time feature.
Level
Auto
Manual
The current time is entered according to the selected country when
connected to a network.
The current time needs to be entered manually.
On/Off Time
Sets the time to turn on or off the monitor set.
Auto Off (15Min.)
If Auto-off is active and there is no input signal, the set switches to off mode automatically
after 15 minutes.
Automatic Standby
Daylight Saving
Time
- It is recommended that you set this feature to [Off] if you intend to use the product for long
periods of time as the feature turns the power of the product off.
If the monitor is left unattended for a set period of time, it automatically goes into standby
mode
- It is recommended that you set this feature to [Off] if you intend to use the product for long
periods of time as the feature turns the power of the product off.
Set the start and end times for Daylight Saving Time. The DST start/end times function only
when you set them more than one day apart from each other.
NOTE
•• Off Time/ On Time can be saved for up to seven schedules; the monitor is turned on or off at the preset time in the
schedule list. If multiple preset times are stored in the schedule list, this function works at the nearest time from the
current time.
•• Once the on or off time is set, these functions operate daily at the preset time.
•• When the scheduled power-on and power-off times are the same, the power-off time has priority over the power-on
time if the set is turned on, and vice versa if the set is turned off.
•• If port 123 is blocked by a firewall, your monitor cannot receive the current time from the network.
ENGLISH
1 Press
to access the main menus.
2 Press the navigation buttons to scroll to TIME and press .
3 Press the navigation buttons to scroll to the setting or option you want and press
30
OPTION Settings
ENGLISH
1 Press
to access the main menus.
2 Press the navigation buttons to scroll to OPTION and press .
3 Press the navigation buttons to scroll to the setting or option you want and press
-- To return to the previous level, press
.
4 When you are finished, press
.
When you return to the previous menu, press
.
.
The available option settings are described in the following:
Setting
Language
Selects a language for the display text.
Country
Select your country.
DivX(R) VOD
Registers or releases DivX.
Checks DivX Registration Code for playing DivX-protected videos.
Register at http://vod.divx.com.
Uses Registration Code to rent or purchase movies at www.divx.com/vod.
* Rented/purchased DivX files cannot be played if the DivX Registration Code of a different
device is used. Use only the DivX Registration Code granted to this device.
* Converted files not conforming to the DivX Codec Standard may not play or may produce
abnormal images.
Deletes all optional settings and returns to initial default mode.
Initial Setting
Set ID
Tile Mode
Description
You can assign a unique Set ID NO (name assignment) to each product when several products
are connected for display. Specify the number (1 to 255 or 1 to 1,000) using the button and
exit. Use the assigned Set ID to individually control each product using the Product Control
Program.
Tile Mode
To use this function
- Must be displayed with various other products.
- Select Tile Mode, set rows and columns, and then enter the tile ID to set
the location.
- Tile Mode: row x column (row = 1-15, column = 1-15).
- 15 x 15 available.
Auto Config.
Sets to adjust the screen position, clock, and phase automatically.
The displayed image may be unstable for a few seconds while the
configuration is in progress.
Position
Moving the screen position horizontally and vertically.
Size
Natural
Reset
Adjust the horizontal and vertical size of the screen taking into account the
size of the bezel.
The image is omitted by the distance between the screens to be naturally
shown.
Function to initialize and release Tile.
All Tile setting are released when selecting Tile recall and the screen returns
to Full screen.
31
Description
Creates simple schedules and sets playback using files in My Media.
Level
Add Schedule
Play
Creates a contents schedule.
- Media: Select the file to which you want to apply the contents schedule.
- Select [Create] to register the contents schedule.
Plays a contents schedule.
Delete All
Deletes all registered schedules.
NOTE
•• Information about registered schedules is stored on your USB storage device. This feature
does not work when your USB storage device has been removed.
•• The picture size is 1920 x 1080.
•• You can use photo and video files only.
•• You can add up to 50 files (photo files + video files = 50).
•• Only photos whose resolution is 1920 x 1080 or below are supported.
•• The default display time for photos is 1 minute. Playback time for movies differs depending
on the running time.
•• You can create up to 7 schedules.
•• You cannot register a schedule when no file has been selected.
•• Contents schedules that have had information forcibly modified using a PC, etc. may not
function properly.
•• With respect to the playback of distribution or contents schedules through SuperSign
Software, the schedule executed last time is played.
Fan Control
(support for only
for some models)
Option
Mode
Fan Operation
Difference
Temperature
Setting
Current
Temperature
Displays the interior temperature information of the product and controls
the mounted fan.
- Auto: the fan operates according to the default temperature set for the
product.
- On: the fan always operates.
- Customizable: the fan operates according to the user preferences.
Shows the difference between the temperatures at which the fan operates
or stops.
Sets the temperature of the operating fan mounted inside the product.
Shows the interior temperature of the product.
NOTE
•• It is recommended to use the auto setting as the incorrect fan settings may cause the
product to malfunction.
•• When the interior temperature of the set exceeds 80 , the set is automatically turned off
for protection.
ENGLISH
Setting
Contents Schedule
32
Tile Mode
ENGLISH
This monitor can be tiled with additional monitors to create a large tiled display.
Off
1X2
2X2
3X3
When the Tile Mode
option is disabled
When using 2 monitors
Tile ID
When using 4 monitors
When using 9 monitors
ID 1
ID 2
ID 1
ID 2
ID 1
ID 2
ID 3
ID 3
ID 4
ID 4
ID 5
ID 6
ID 7
ID 8
ID 9
Tile ID
4X4
5X5
When using 16 monitors
When using 25 monitors
ID 1
ID 2
ID 3
ID 4
ID 1
ID 2
ID 3
ID 4
ID 5
ID 5
ID 6
ID 7
ID 8
ID 6
ID 7
ID 8
ID 9
ID 10
ID 9
ID 10
ID 11
ID 12
ID 11
ID 12
ID 13
ID 14
ID 15
ID 13
ID 14
ID 15
ID 16
ID 16
ID 17
ID 18
ID 19
ID 20
ID 21
ID 22
ID 23
ID 24
ID 25
Tile Mode - Natural mode
When active, the part of the image that would normally be displayed in the gap between the monitors is omitted.
Before
After
33
NETWORK Settings
-- To return to the previous level, press
.
4 When you are finished, press
.
When you return to the previous menu, press
.
.
The available option settings are described in the following:
Setting
Network Setting
Description
Configure the network settings.
Network
setting
Network Status
When the Wi-Fi dongle is connected, you can view and connect to any
available wireless network.
Display the network status.
Network Connection Options
Setting
Description
Setting from the AP list
Select an AP to connect to a wireless network.
Simple setting
Press the button on the wireless router that supports PBC to easily connect to
the router.
(WPS-button mode)
ENGLISH
1 Press
to access the main menus.
2 Press the navigation buttons to scroll to NETWORK and press .
3 Press the navigation buttons to scroll to the setting or option you want and press
34
ENGLISH
PICTURE ID Settings
AUDIO
•• Only applies to certain models.
is used to change the settings of a specific set (display) using a single IR receiver for multi-vision.
Communication is possible between a monitor with an IR receiver and other monitors using RS-232C cables. Each
monitor is identified by a Set ID. If you assign the
using the remote control, only displays with matching
and Set ID can be controlled remotely.
(RGB/DVI)
RS-232C OUT
RS-232C OUT
RS-232C OUT
RS-232C IN
RS-232C IN
RS-232C IN
REMOTE
CONTROL IN
1 Assign the Set ID to the installed monitors as shown below.
IR & Light Sensor
RS-232C cables
PICTURE ID
ON [2]
2 Press the red ON button on the remote control to assign the PICTURE ID.
3 Assign the Set ID to the selection of your choice.
•• A set with a different Set ID from the PICTURE ID cannot be controlled by IR signals.
NOTE
•• If PICTURE ID is set to 2, only the upper right monitor, which has a Set ID of 2, can be controlled by IR signals.
•• If you press the green OFF button for PICTURE ID, the PICTURE IDs for all monitors are turned off. If you then press
any button on the remote control, all monitors can be controlled by IR signals regardless of Set ID.
35
ENGLISH
IR CODES
•• All models do not support the HDMI/USB function.
•• Some key codes are not supported depending on the model.
Code (Hex)
Function
08
(Power)
Note
R/C BUTTON
0B
R/C BUTTON
C4
MONITOR ON
C5
MONITOR OFF
95
R/C BUTTON
R/C BUTTON
(
)
R/C BUTTON
DC
10 to 19
Number Key 0 to 9
R/C BUTTON
R/C BUTTON
32
/ /
R/C BUTTON
2F
R/C BUTTON
02
(+)
R/C BUTTON
03
(-)
R/C BUTTON
79
R/C BUTTON
99
R/C BUTTON
09
R/C BUTTON
E0
R/C BUTTON
E1
R/C BUTTON
4D
R/C BUTTON
AA
R/C BUTTON
5F
R/C BUTTON
43
R/C BUTTON
40
Up
R/C BUTTON
41
Down
R/C BUTTON
07
Left
R/C BUTTON
06
Right
R/C BUTTON
3F
R/C BUTTON
44
R/C BUTTON
28
R/C BUTTON
5B
R/C BUTTON
7E
R/C BUTTON
7B
R/C BUTTON
B1
R/C BUTTON
B0
R/C BUTTON
BA
R/C BUTTON
36
Code (Hex)
Function
Note
ENGLISH
8F
R/C BUTTON
8E
R/C BUTTON
72
R/C BUTTON
71
Red Key (
Green Key (
)
63
Yellow Key
R/C BUTTON
61
Blue Key
R/C BUTTON
)
R/C BUTTON
TO CONTROL MULTIPLE PRODUCTS
•• Use this method to connect several products to a single PC. You can control several products at a time by connecting
them to a single PC.
•• In the Option menu, Set ID must be between 1 and 255 (or from 1 to 1,000) without being duplicated.
Connecting the Cable
Connect the RS-232C cable as shown in the picture.
•• The RS-232C protocol is used for communication between the PC and product. You can turn the product on or off,
select an input source or adjust the OSD menu from your PC.
Monitor 4
RS-232C
OUT
RS-232C
IN
Monitor 3
RS-232C
OUT
RS-232C
IN
Monitor 2
RS-232C
OUT
RS-232C
IN
4P Cable
(not included)
PC
Monitor 1
RS-232C
OUT
RS-232C
IN
RS-232C
Gender
RS-232C Cable
(not included)
37
ENGLISH
RS-232C Configurations
4P Cable
•• 4-Wire Configurations (Standard RS-232C cable)
RXD
TXD
GND
IR
TXD
RXD
GND
IR
NOTE
•• When using three-wire connections (non-standard), an IR daisy chain cannot be used.
•• If you want to control multiple units simultaneously, use 3.5 mm 4-pole cables (sold separately).
RS-232C Cable
•• 8-Wire Configurations (Standard RS-232C cable)
DCD
RXD
TXD
GND
DTR
DSR
RTS
CTS
PC
RS-232C
Gender
1
2
3
5
4
6
7
8
1
3
2
5
6
4
8
7
D-Sub 9
(Female)
DCD
TXD
RXD
GND
DSR
DTR
CTS
RTS
D-Sub 9
(Female)
Communication Parameter
•• Baud Rate : 9600 BPS
•• Data Length : 8 bit
•• Parity Bit : None
•• Stop Bit : 1 bit
•• Flow Control : None
•• Communication Code : ASCII code
•• Use a crossed (reverse) cable
38
ENGLISH
Command Reference List
COMMAND
1
DATA
(Hexadecimal)
2
01
Power
k
a
00 to 01
02
Select input
x
b
See [Select input]
03
Aspect ratio
k
c
See [Aspect ratio]
04
Energy saving
j
q
See [Energy saving]
05
Picture mode
d
x
See [Picture mode]
06
Contrast
k
g
00 to 64
07
Brightness
k
h
00 to 64
08
Sharpness
k
k
00 to 32
09
Color
k
i
00 to 64
10
Tint
k
j
00 to 64
11
Color temperature
x
u
00 to 64
12
H position
f
q
00 to 64
13
V position
f
r
00 to 64
14
H size
f
s
00 to 64
15
Auto Config.
j
u
01
16
Balance
k
t
00 to 64
17
Sound Mode
d
y
See [Sound mode]
18
Mute
k
e
00 to 01
19
Volume
k
f
00 to 64
20
Clock 1 (year/month/day)
f
a
See [Clock 1]
21
Clock 2 (hour/minute/second)
f
x
See [Clock 2]
22
Off time schedule
f
c
00 to 01
23
On time schedule
f
b
00 to 01
24
Off timer (repeat mode/time)
f
e
See [Off timer]
25
On timer (repeat mode/time)
f
d
See [On timer]
26
On timer input
f
u
See [On timer input]
27
Automatic Standby
m
n
00 to 01
28
Auto off
f
g
00 to 01
29
Language
f
i
See [Language]
30
Reset
f
k
00 to 02
31
Current temperature
d
n
FF
32
Key
m
c
See [Key]
33
Time elapsed
d
l
FF
39
COMMAND
2
DATA
(Hexadecimal)
34
Product serial number
f
y
FF
35
Software version
f
z
FF
36
White balance red gain
j
m
00 to FE
37
White balance green gain
j
n
00 to FE
38
White balance blue gain
j
o
00 to FE
39
White Balance Red Offset
s
x
00 to 7F
40
White Balance Green Offset
s
y
00 to 7F
41
White Balance Blue Offset
s
z
00 to 7F
42
Backlight
m
g
00 to 64
43
Screen off
k
d
00 to 01
44
Tile Mode
d
d
See [Tile Mode]
45
Tile Mode Check
d
z
FF
46
Tile ID
d
i
Refer to ‘Tile ID'.
47
Tile H Position
d
e
00 to 32
48
Tile V Position
d
f
00 to 32
49
Tile H Size
d
g
00 to 32
50
Tile V Size
d
h
00 to 32
51
Natural Mode (In Tile mode)
d
j
00 to 01
NOTE
•• During USB operations such as Dvix or EMF, all commands except Power (k a) and Key (m c) are not executed and
treated as NG.
•• Some commands are not supported depending on the model.
•• The ‘f f’ command which shows the status of a certain command does not display the OSD as the result in order to be
compatible with SuperSign program.
ENGLISH
1
40
ENGLISH
Transmission / Receiving Protocol
Transmission
[Command1][Command2][ ][Set ID][ ][Data][Cr]
* [Command1]
Identifies the factory setting and the user setting modes.
* [Command2]
Controls monitors.
* [Set ID]
* [Cr]
Used for selecting a set you want to control. A Set ID can be assigned to each set from 1 to
255 (from 01H to FFH), or from 1 to 1,000 (from 001H to 3e8H) in certain models, under
OPTION in the OSD menu. Selecting '00H' or '000H' for Set ID allows the simultaneous control
of all connected monitors. (It may not be supported depending on the model.)
Transmits command data.
Data count may increase depending on the command.
Carriage Return. Corresponds to '0x0D' in ASCII code.
*[]
White Space. Corresponds to '0x20' in ASCII code.
* [Data]
Acknowledgement
[Command2][ ][Set ID][ ][OK/NG][Data][x]
* The Product transmits an ACK (acknowledgement) based on this format when receiving normal data. At this time,
if the data is FF, it indicates the present status data. If the data is in data write mode, it returns the data of the PC
computer.
* If a command is sent with Set ID ‘00’ (=0x00) or ‘000 (=0x000)’, the data is reflected to all monitor sets and they do
send any acknowledgement (ACK).
* If the data value ‘FF’ is sent in control mode via RS-232C, the current setting value of a function can be checked (only
for some functions).
* Some commands may not be supported on some models.
41
03. Aspect ratio (Command: k c)
Adjusts the aspect ratio.
Transmission
Transmission
[k][a][ ][Set ID][ ][Data][Cr]
[k][c][ ][Set ID][ ][Data][Cr]
Data
00: Off
01: On
Data
Acknowledgement
[a][ ][Set ID][ ][OK/NG][Data][x]
* Only when the monitor is fully powered on, the
acknowledgement signal is returned properly.
* There may be a delay between the transmission and
acknowledgement signals.
02. Select input(Command: x b)
Selects an input signal.
Transmission
[x][b][ ][Set ID][ ][Data][Cr]
Data
20: AV
40: Component
60: RGB
90: HDMI (HDMI1) (DTV)
A0: HDMI (HDMI1) (PC)
91: HDMI2/OPS (DTV)
A1: HDMI2/OPS (PC)
70: DVI-D(PC)
80: DVI-D(DTV)
C0:DP(DTV)
D0:DP(PC)
Acknowledgement
[b][ ][Set ID][ ][OK/NG][Data][x]
* Some input signals may not be supported on some
models.
01: 4:3
02: 16:9
04: Zoom (HDMI)(DTV)
06: Auto ratio(HDMI)(DTV)
09: Original (≥ 720p) (HDMI) (DTV)
10 to 1F: Cinema zoom 1 to 16 (HDMI) (DTV)
* Available data types differ depending on the input
signal. For more information, see the aspect ratio
section of the owner’s manual.
* The aspect ratio may differ depending on the model’s
input configuration.
Acknowledgement
[c][ ][Set ID][ ][OK/NG][Data][x]
04. Energy saving (Command: j q)
Sets the energy saving function.
Transmission
[j][q][ ][Set ID][ ][Data][Cr]
Data
00: Off
01: Minimum
02: Medium
03: Maximum
04: Automatic
05: Screen off
Acknowledgement
[q][ ][Set ID][ ][OK/NG][Data][x]
* This may not be supported on some models.
ENGLISH
01. Power (Command: k a)
Controls the power on/off of the set.
42
ENGLISH
05. Picture mode (Command: d x)
Selects a picture mode.
08. Sharpness (Command: k k)
Adjusts the screen sharpness.
Transmission
Transmission
[d][x][ ][Set ID][ ][Data][Cr]
[k][k][ ][Set ID][ ][Data][Cr]
Data
00: Vivid
01: Standard
02: Cinema
03: Sport
04: Game
05: Expert 1
06: Expert 2
08: Eco
11 : Calibration
Acknowledgement
[x][ ][Set ID][ ][OK/NG][Data][x]
Data
00 to 32: Sharpness 0 to 50
Acknowledgement
[k][ ][Set ID][ ][OK/NG][Data][x]
09. Color (Command: k i)
Adjusts the screen color.
Transmission
[k][i][ ][Set ID][ ][Data][Cr]
Data
00 to 64: Color 0 to 100
Acknowledgement
[i][ ][Set ID][ ][OK/NG][Data][x]
06. Contrast (Command: k g)
Adjusts the screen contrast.
Transmission
[k][g][ ][Set ID][ ][Data][Cr]
Data
00 to 64: Contrast 0 to 100
Acknowledgement
[g][ ][Set ID][ ][OK/NG][Data][x]
10. Tint (Command: k j)
Adjusts the screen tint.
Transmission
[k][j][ ][Set ID][ ][Data][Cr]
Data
00 to 64: Tint red 50 to green 50
Acknowledgement
[j][ ][Set ID][ ][OK/NG][Data][x]
07. Brightness (Command: k h)
Adjusts the screen brightness.
Transmission
[k][h][ ][Set ID][ ][Data][Cr]
Data
00 to 64: Brightness 0 to 100
Acknowledgement
[h][ ][Set ID][ ][OK/NG][Data][x]
11. Color temperature (Command: x u)
Adjusts the screen color temperature.
Transmission
[x][u][ ][Set ID][ ][Data][Cr]
Data
00 to 64: Warm 50 to cool 50
Acknowledgement
[u][ ][Set ID][ ][OK/NG][Data][x]
43
14. H size (Command: f s)
Adjusts the horizontal size of the screen.
This function is only available when the Tile Mode is set
to Off.
* The operational range varies depending on the RGB
input resolution. (Only available in RGB-PC input
mode)
* The operational range varies depending on the RGB
input resolution. (Only available in RGB-PC input
mode)
Transmission
[f][q][ ][Set ID][ ][Data][Cr]
Data
00 to 64: Min -50 (left) to max 50 (right)
Transmission
[f][s][ ][Set ID][ ][Data][Cr]
Data
00 to 64: Min -50 (small) to max 50 (large)
Acknowledgement
Acknowledgement
[q][ ][Set ID][ ][OK/NG][Data][x]
[s][ ][Set ID][ ][OK/NG][Data][x]
13. V position (Command: f r)
Adjusts the vertical position of the screen.
This function is only available when the Tile Mode is set
to Off.
* The operational range varies depending on the RGB
input resolution. (Only available in RGB-PC input
mode)
Transmission
[f][r][ ][Set ID][ ][Data][Cr]
Data
15. Auto Config. (Command: j u)
Automatically corrects position and shaking of the
picture. (Only available in RGB-PC input mode)
Transmission
[j][u][ ][Set ID][ ][Data][Cr]
Data
01: Execution
Acknowledgement
[u][ ][Set ID][ ][OK/NG][Data][x]
00 to 64: Min -50 (down) to max 50 (up)
Acknowledgement
[r][ ][Set ID][ ][OK/NG][Data][x]
16. Balance (Command: k t)
Adjusts the sound balance.
Transmission
[k][t][ ][Set ID][ ][Data][Cr]
Data
00 to 64: Left 50 to right 50
Acknowledgement
[t][ ][Set ID][ ][OK/NG][Data][x]
ENGLISH
12. H position (Command: f q)
Adjusts the horizontal position of the screen.
This function is only available when the Tile Mode is set
to Off.
44
ENGLISH
17. Sound mode (Command: d y)
Selects a sound mode.
20. Clock 1 (year/month/day) (Command: f a)
Adjusts the Clock 1 (year/month/day) value.
Transmission
Transmission
[d][y][ ][Set ID][ ][Data][Cr]
[f][a][ ][Set ID][ ][Data1][ ][Data2][ ][Data3][Cr]
Data
01: Standard
02: Music
03: Cinema
04: Sport
05. Game
07. News
Acknowledgement
[y][ ][Set ID][ ][OK/NG][Data][x]
18. Mute (Command: k e)
Mutes/unmutes the sound.
Transmission
[k][e][ ][Set ID][ ][Data][Cr]
Data
00: Mute
01: Unmute
Acknowledgement
[e][ ][Set ID][ ][OK/NG][Data][x]
19. Volume (Command: k f)
Adjusts the playback volume.
Transmission
[k][f][ ][Set ID][ ][Data][Cr]
Data
00 to 64: Volume 0 to 100
Acknowledgement
[f][ ][Set ID][ ][OK/NG][Data][x]
Data1 00 to 14: Year 2010 to 2040
Data2 01 to 0C: January to December
Data3 01 to 1F: 1st to 31st
* Enter “fa [Set ID] ff” to view the Clock 1 (year/
month/day) settings.
Acknowledgement
[a][ ][Set ID][ ][OK/NG][Data1][Data2][Data3][x]
45
24. Off timer (repeat mode/time) (Command: f e)
Configures the off time (repeat mode/time) settings.
Transmission
Transmission
[f][x][ ][Set ID][ ][Data1][ ][Data2][ ][Data3][Cr]
[f][e][ ][Set ID][ ][Data1][ ][Data2][ ][Data3][Cr]
Data1
Data2
Data3
00 to 17: 00 to 23 hours
00 to 3B: 00 to 59 minutes
00 to 3B: 00 to 59 seconds
* Enter “fa [Set ID] ff” to view the Clock 2 (hour/
minute/second) settings.
* This function is only available when Clock 1 (year/
month/day) is set.
Acknowledgement
[x][ ][Set ID][ ][OK/NG][Data1][Data2][Data3][x]
22. Off time schedule (Command: f c)
Enables/disables the on time schedule.
Transmission
[f][c][ ][Set ID][ ][Data][Cr]
Data
00: Off
01: On
Acknowledgement
[c][ ][Set ID][ ][OK/NG][Data][x]
23. On time schedule (Command: f b)
Enables/disables the on time schedule.
Transmission
[f][b][ ][Set ID][ ][Data][Cr]
Data
00: Off
01: On
Acknowledgement
[b][ ][Set ID][ ][OK/NG][Data][x]
Data1
1. F1 to F7 (reading data)
F1: Read the 1st off timer data
F2: Read the 2nd off timer data
F3: Read the 3rd off timer data
F4: Read the 4th off timer data
F5: Read the 5th off timer data
F6: Read the 6th off timer data
F7: Read the 7th off timer data
2. E1 to E7 (deleting one index), E0 (deleting all
indexes)
E0: Erase all off timer setting
E1: Erase the 1st off timer setting
E2: Erase the 2nd off timer setting
E3: Erase the 3rd off timer setting
E4: Erase the 4th off timer setting
E5: Erase the 5th off timer setting
E6: Erase the 6th off timer setting
E7: Erase the 7th off timer setting
3. 01 to 0C (setting the day of the week for off timer)
01: Once
02. Daily
03: Mon - Fri
04: Mon - Sat
05: Sat - Sun
06. Every Sunday
07. Every Monday
08. Every Tuesday
09. Every Wednesday
0A. Every Thursday
0B. Every Friday
0C. Every Saturday
Data2 00 to 17: 00 to 23 hours
Data3 00 to 3B: 00 to 59 minutes
ENGLISH
21. Clock 2 (hour/minute/second) (Command: f x)
Adjusts the Clock 2 (hour/minute/second) value.
46
ENGLISH
* To read or delete the Off Time list, set FFH for
[Data2] and [Data3].
Example 1: fe 01 f1 ff ff - Read the 1st index data
from off timer
Example 2: fe 01 e1 ff ff - Delete the 1st index data
from off timer.
Example 3: fe 01 04 02 03 - Sets Off Timer to 02:03
for Monday-Saturday.
* This function is only available when Clock 1 (year/
month/day) and Clock 2 (hour/minute/second) are
set.
Acknowledgement
[e][ ][Set ID][ ][OK/NG][Data1][Data2][Data3][x]
25. On timer (repeat mode/time) (Command: f d)
Configures the on time (repeat mode/time) settings.
Transmission
[f][d][ ][Set ID][ ][Data1][ ][Data2][ ][Data3][Cr]
Data1
1. F1 to F7 (reading data)
F1: Read the 1st on timer data
F2: Read the 2nd on timer data
F3: Read the 3rd on timer data
F4: Read the 4th on timer data
F5: Read the 5th on timer data
F6: Read the 6th on timer data
F7: Read the 7th on timer data
2. E1 to E7 (deleting one index), E0 (deleting all
indexes)
E0: Erase all on timer setting
E1: Erase the 1st on timer setting
E2: Erase the 2nd on timer setting
E3: Erase the 3rd on timer setting
E4: Erase the 4th on timer setting
E5: Erase the 5th on timer setting
E6: Erase the 6th on timer setting
E7: Erase the 7th on timer setting
3. 01 to 0C (setting the day of the week for the on
timer)
01: Once
02. Daily
03: Mon - Fri
04: Mon - Sat
05: Sat - Sun
06. Every Sunday
07. Every Monday
08. Every Tuesday
09. Every Wednesday
0A. Every Thursday
0B. Every Friday
0C. Every Saturday
Data2 00 to 17: 00 to 23 hours
Data3 00 to 3B: 00 to 59 minutes
* To read or delete an on timer list you have set,
[Data2][Data3] must be set to FFH.
Example 1: fd 01 f1 ff ff - Read the 1st index data
from on timer.
Example 2: fd 01 e1 ff ff - Delete the 1st index data
from on timer.
Example 3: fd 01 04 02 03 - Set on timer at 02:03
on Monday to Saturday.
* This function is only available when Clock 1 (year/
month/day) and Clock 2 (hour/minute/second) are
set.
Acknowledgement
[d][ ][Set ID][ ][OK/NG][Data1][Data2][Data3][x]
47
Transmission
[f][u][ ][Set ID][ ][Data1][Cr]
[f][u][ ][Set ID][ ][Data1][Data2][Cr]
Data (adding schedule)
20: AV
40: Component
60: RGB
70: DVI-D
90: HDMI (HDMI1) (DTV)
91: HDMI2/OPS (DTV)
C0: DISPLAYPORT (DTV)
Data2
1. ffh (reading data)
To read the schedule input, enter FFH for [Data2].
If no schedule is available for [Data1] when attempting
to read or change the schedule data, the text NG will be
displayed and the operation will fail.
(Example 1: fu 01 60 - Move existing schedule entries
down one row each and save RGB as input source for
the 1st schedule entry.)
(Example 2: fu 01 f1 ff - Read the 1st schedule input
data.)
* This function is only supported when 1 (year/month/
date), 2 (hour/minute/second) and On Time (repeat
mode/time) are set.
* Input may not be supported on some models.
Acknowledgement
Data1
1. f1h to f7h (reading data)
F1: Select the 1st schedule input source
F2: Select the 2nd schedule input source
F3: Select the 3rd schedule input source
F4: Select the 4th schedule input source
F5: Select the 5th schedule input source
F6: Select the 6th schedule input source
F7: Select the 7th schedule input source
[u][ ][Set ID][ ][OK/NG][Data][x]
[u][ ][Set ID][ ][OK/NG][Data1][Data2][x]
27. Automatic standby (Command: m n)
Configures the automatic standby settings.
Transmission
[m][n][ ][Set ID][ ][Data][Cr]
Data
00: Off (Will not turn off after 4/6/8 hours)
01: 4 hours (Off after 4 hours)
02: 6 hours (Off after 6 hours)
03: 8 hours (Off after 8 hours)
Acknowledgement
[n][ ][Set ID][ ][OK/NG][Data][x]
28. Auto off (Command: f g)
Configures the automatic off settings.
Transmission
[f][g][ ][Set ID][ ][Data][Cr]
Data
00: Off (Will not turn off after 15 minutes)
01: On (Off after 15 minutes)
Acknowledgement
[g][ ][Set ID][ ][OK/NG][Data][x]
ENGLISH
26. On timer input (Command: f u)
Adds a new schedule entry by selecting input for the
current on timer setting.
48
ENGLISH
29. Language (Command: f i)
Sets the OSD language.
31. Current temperature (Command: d n)
Checks the inside temperature value.
Transmission
Transmission
[f][i][ ][Set ID][ ][Data][Cr]
[d][n][ ][Set ID][ ][Data][Cr]
Data
00: Czech
01: Danish
02: German
03: English
04: Spanish (Europe)
05: Greek
06: French
07: Italian
08: Dutch
09: Norwegian
0A: Portuguese
0B: Portuguese (Brazil)
0C: Russian
0D: Finnish
0E: Swedish
0F: Korean
10: Chinese (Cantonese)
11: Japanese
12: Chinese (Mandarin)
13: Arabic
Acknowledgement
[i][ ][Set ID][ ][OK/NG][Data][x]
* This may not be supported on some models.
Data FF: Check status
Acknowledgement
[n][ ][Set ID][ ][OK/NG][Data][x]
[n][ ][Set ID][ ][OK/NG][Data1][Data2][Data3][x]
* Temperature is displayed as a hexadecimal value.
32. Key (Command: m c)
Sends a key code for the IR remote control.
Transmission
[m][c][ ][Set ID][ ][Data][Cr]
Data
[c][ ][Set ID][ ][OK/NG][Data][x]
For key codes, see IR Codes.
* Some key codes may not be supported on some
models.
33. Time elapsed (Command: d l)
Checks the elapsed time.
Transmission
[d][l][ ][Set ID][ ][Data][Cr]
Data
30. Reset (Command: f k)
Resets settings for Picture, Screen and Audio or
restores factory settings.
(Screen reset can only be performed in RGB input
mode.)
Transmission
[f][k][ ][Set ID][ ][Data][Cr]
Data
00: Picture reset
01: Screen reset
02: Initial settings (factory reset)
Acknowledgement
[k][ ][Set ID][ ][OK/NG][Data][x]
IR_KEY_CODE
Acknowledgement
FF: Read status
Acknowledgement
[l][ ][Set ID][ ][OK/NG][Data][x]
* The data received is shown as a hexadecimal value.
49
38. White balance blue gain (Command: j o)
Adjusts the white balance blue gain value.
Transmission
Transmission
[f][y][ ][Set ID][ ][Data][Cr]
[j][o][ ][Set ID][ ][Data][Cr]
Data
FF: Check product serial number
Data 00 to FE: Blue gain 0 to 254
Acknowledgement
Acknowledgement
[y][ ][Set ID][ ][OK/NG][Data][x]
[o][ ][Set ID][ ][OK/NG][Data][x]
* Data is in ASCII code.
35. Software version (Command: f z)
Checks the software version of the product.
Transmission
[f][z][ ][Set ID][ ][Data][Cr]
Data
39. White Balance Red Offset(Command: s x)
Adjusts the white balance red offset value.
Transmission
[s][x][ ][Set ID][ ][Data][Cr]
Data
FF: Check software version
00 to 7F: Red offset 0 to 127
FF: Confirms red offset value
Acknowledgement
Acknowledgement
[z][ ][Set ID][ ][OK/NG][Data][x]
[x][ ][Set ID][ ][OK/NG][Data][x]
36. White balance red gain (Command: j m)
Adjusts the white balance red gain value.
40. White Balance Green Offset (Command: s y)
Adjusts the white balance green offset value.
Transmission
Transmission
[j][m][ ][Set ID][ ][Data][Cr]
[s][y][ ][Set ID][ ][Data][Cr]
Data 00 to FE: Red gain 0 to 254
Data
Acknowledgement
[m][ ][Set ID][ ][OK/NG][Data][x]
00 to 7F: Green offset 0 to 127
FF: Confirms green offset value
Acknowledgement
[y][ ][Set ID][ ][OK/NG][Data][x]
37. White balance green gain (Command: j n)
Adjusts the white balance green gain value.
Transmission
[j][n][ ][Set ID][ ][Data][Cr]
Data 00 to FE: Green gain 0 to 254
Acknowledgement
[n][ ][Set ID][ ][OK/NG][Data][x]
41. White Balance Blue Offset (Command: s z)
Adjusts the white balance blue offset value.
Transmission
[s][z][ ][Set ID][ ][Data][Cr]
Data
00 to 7F: Blue offset 0 to 127
FF: Confirms blue offset value
Acknowledgement
[z][ ][Set ID][ ][OK/NG][Data][x]
ENGLISH
34. Product serial number (Command: f y)
Checks the serial number of the product.
50
ENGLISH
42. Backlight (Command: m g)
Adjusts the back light brightness.
45. Tile Mode Check (Command: d z)
To check Tile Mode status.
Transmission
Transmission
[m][g][ ][Set ID][ ][Data][Cr]
[d][z][ ][Set ID][ ][Data][Cr]
Data
00 to 64: Back light brightness 0 to 100
Acknowledgement
[g][][set ID][][OK/NG][Data][x]
* This may not be supported on some models.
Data
Acknowledgement
[z][ ][Set ID][ ][OK/NG][Data1][Data2][Data3][x]
Data1
43. Screen off (Command: k d)
Turns the screen on or off.
FF: Check Tile Mode status.
* It may not be supported depending on the model.
Data2
Data3
00: Tile Mode Off
01: Tile Mode On
00 to 0F: Tile Row
00 to 0F: Tile Column
Transmission
[k][d][ ][Set ID][ ][Data][Cr]
Data
00: Turns the screen on
01: Turns the screen off
Acknowledgement
[d][ ][Set ID][ ][OK/NG][Data][x]
44. Tile Mode (Command: d d)
To set a Tile Mode and Tile Column/ Row values.
Transmission
[d][d][ ][Set ID][ ][Data][Cr]
Data
00 to FF: 1
st byte - Tile Row 2nd byte - Tile Column
* 00, 01, 10, 11 means Tile Mode Off
46. Tile ID (Command: d i)
To set Tile ID.
Transmission
[d][i][ ][Set ID][ ][Data][Cr]
Data
01 to E1:
Tile ID 01 to 225**
FF: Check Tile ID
* Data could not be set over (Tile Column) x (Tile Row).
* It may not be supported depending on the model.
Acknowledgement
[i][ ][Set ID][ ][OK/NG][Data][x]
* NG will be return if data is over (Tile Column) x (Tile
Row), except 0xFF.
* It may not be supported depending on the model.
Acknowledgement
[d][ ][Set ID][ ][OK/NG][Data][x]
47. Tile H Position (Command: d e)
To adjust the Tile Horizontal position.
* This function is available only when the Natural option
of the Tile Mode is set to Off while the Tile Mode set
to On.
Transmission
[d][e][ ][Set ID][ ][Data][Cr]
Data
00 to 32: -50 (Left) to 0 (Right)
* Left/Right values depend on Tile H size.
* It may not be supported depending on the model.
Acknowledgement
[e][ ][Set ID][ ][OK/NG][Data][x]
51
* This function is available only when the Natural option
of the Tile Mode is set to Off while the Tile Mode set
to On.
Transmission
[d][f][ ][Set ID][ ][Data][Cr]
Data
0 to 32: 0 (Bottom) to 50 (Top)
51. Natural Mode (In Tile Mode) (Command: d j)
To display the image naturally, the part of the image
that would normally be displayed in the gap between
the monitors is omitted.
Transmission
[d][j][ ][Set ID][ ][Data][Cr]
Data
00: Off
01: On
* Bottom/Top values depend on Tile Vertical size.
Acknowledgement
* It may not be supported depending on the model.
[j][ ][Set ID][ ][OK/NG][Data][x]
Acknowledgement
[f][ ][Set ID][ ][OK/NG][Data][x]
49. Tile H Size (Command: d g)
To adjust the Tile Horizontal Size.
* Set Tile H Position to 0x32 before setting Tile H Size.
* This function is available only when the Natural option
of the Tile Mode is set to Off while the Tile Mode set
to On.
Transmission
[d][g][ ][Set ID][ ][Data][Cr]
Data
00 to 32: 0 to 50
* It may not be supported depending on the model.
Acknowledgement
[g][ ][Set ID][ ][OK/NG][Data][x]
50. Tile V Size (Command: d h)
To adjust the Tile Vertical size.
* Set Tile V Position to 0x00 before setting Tile V Size.
* This function is available only when the Natural option
of the Tile Mode is set to Off while the Tile Mode set
to On.
Transmission
[d][h][ ][Set ID][ ][Data][Cr]
Data
00 to 32: 0 to 50
* It may not be supported depending on the model.
Acknowledgement
[h][ ][Set ID][ ][OK/NG][Data][x]
ENGLISH
48. Tile V Position (Command: d f)
To adjust the Tile Vertical position.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising