LG | 27HK510S-W | Owner's Manual | LG 27HK510S-W Owner’s Manual

LG 27HK510S-W Owner’s Manual
OWNER’S MANUAL
IPS LED Monitor
(LED Monitor*)
* LG LED Monitor applies LCD screen with LED backlights.
Please read this manual carefully before operating your set and
retain it for future reference.
27HK510S
www.lg.com
Copyright 2019 LG Electronics Inc. All Rights Reserved.
CONTENTS
ON CLEANING...........................................3
ENGLISH
LICENSE....................................................3
OPEN SOURCE SOFTWARE
NOTICE INFORMATION..............................3
ASSEMBLY AND PREPARING.....................4
USER SETTINGS......................................14
TROUBLESHOOTING...............................33
PRODUCT SPECIFICATIONS.....................35
EXTERNAL CONTROLLER SETUP.............39
2
ON CLEANING
LICENSE
Each model has different licenses. Visit www.lg.com for more information on the license.
•
•
•
•
Isopropanol 100%
Ethanol 70%
Cidex® OPA
0.9% NaCl solution
How to Use Cleaner
•
•
•
•
•
•
Prior to cleaning, turn off the monitor and remove the power cable.
Soak a soft cloth in a recommended cleaner, then lightly rub the screen with no more than 1 N of force.
The cleaner could cause serious damage if it leaks inside the monitor while cleaning.
The display could be damaged, so only clean the parts of the monitor other than the screen's LCD panel.
Do not use benzene, thinner, acids or alkaline cleaners or other such solvents.
Cleaning guidelines for displays must only be carried out by medical professionals (Doctors or Nurses) and must
not be handled by patients.
The terms HDMI and HDMI High-Definition Multimedia Interface,
and the HDMI Logo are trademarks or registered trademarks of
HDMI Licensing Administrator, Inc. in the United States and other
countries.
ENGLISH
Recommended Cleaning Chemicals
The SuperSpeed USB Trident logo is a registered trademark of USB
Implementers Forum, Inc.
OPEN SOURCE SOFTWARE NOTICE
INFORMATION
To obtain the source code under GPL, LGPL, MPL, and other open source licenses, that is contained in this product,
please visit http://opensource.lge.com.
In addition to the source code, all referred license terms, warranty disclaimers and copyright notices are available
for download.
LG Electronics will also provide open source code to you on CD-ROM for a charge covering the cost of performing
such distribution (such as the cost of media, shipping, and handling) upon email request to opensource@lge.com.
This offer is valid for a period of three years after our last shipment of this product. This offer is valid to anyone in
receipt of this information.
3
ASSEMBLY AND PREPARING
ENGLISH
4
Product Composition
Please check whether all the components are included in the box before using the product. If there are any missing components, contact the retailer where you purchased the product.
Note that the product and related components may look different from those shown here.
CD (Software/Owner's Manual)/Regulatory
Manual/Cards
Power Cord
DVI Cable
HDMI Cable
AC/DC Adaptor
DVI-I to D-SUB Gender Cable
CAUTION
Always use genuine LG components to ensure safety and product performance.
The product warranty will not cover damage or injury caused by the use of unauthorized components.
It is recommend that use the supplied components.
If you use generic cables not certified by LG, the screen may not display or there may be image noises.
NOTE
• The components may look different from those illustrated here.
• Without prior notice, all product information and specifications contained in this manual are subject to change
to improve the performance of the product.
• To purchase optional accessories, visit an electronics store or an online shopping site, or contact the retailer
from which you purchased the product.
• The power cord provided may differ depending upon the region.
Supported Drivers and Software
Check the drivers and software supported by your product and refer to the manuals on the CD enclosed in the
product package.
Drivers and Software
Installation Priority
27HK510S
Monitor Driver
Recommended
O
True Color Pro
Optional
O
ENGLISH
•
•
•
•
• Required and Recommended: You can download and install the latest version from the enclosed CD or from the
LGE website (www.lg.com).
• Optional: You can download and install the latest version from the LGE website (www.lg.com).
5
Product and LED Control buttons
ENGLISH
1
2
3
4
5
6
7
8
9
6
LED Control button Functions
Selects the input mode.
2
Displays the screens of two input modes on one monitor.
3
Opens the [Hot key Settings] menu.
4
Adjusts the screen brightness.
5
Selects and confirms menus or options
* Automatically sets screen to optimal settings in analog video signal.
Adjusts the screen contrast.
Displays LED Control buttons on the front panel and opens the menu mode.
6
7
8
Power indicator
The green indicator illuminates if the power is on. The arrow indicates the position of the power switch.
9
Power switch
Turns the power on/off.
ENGLISH
1
NOTE
• The Power button is located at the bottom right on the front of the monitor.
• If the Control Key LED is turned off, press the Control Key
button to turn the Control button LED on. When the Control Key LED is turned on, you can control the Control Key functions.
7
Connectors
ENGLISH
DC-IN
(19 - 24 V
RS-232C
COMPOSITE
IN
)
S-VIDEO
IN
DC-IN
(19 - 24 V
DC-IN
(19 - 24 V
DC-IN
(19 - 24 V
1
8
2
)
RS-232C
3
)
COMPOSITE
IN
S-VIDEO
IN
4
5
RS-232C
RS-232C
COMPOSITE
IN
)
COMPOSITE
IN
DVI OUT
DVI / RGBS
/ COMPONENT IN
S-VIDEO
IN
S-VIDEO
IN
DVI / RGBS
/ COMPONENT IN
DVI / RGBS
/ COMPONENT IN
DVI / RGBS
/ COMPONENT IN
SDI IN
DVI OUT
SDI IN
DVI OUT
SDI OUT
HDMI IN
SDI IN
DVI OUT
6
SERVICE ONLY
SDI OUT
SDI OUT
5V
SERVICE ONLY
HDMI IN
5V
0.9 A
0.9 A
HDMI IN
SERVICE ONLY
5V
SDI IN
0.9 A
SDI OUT
7
HDMI IN
8
SERVICE ONLY
5V
9
0.9 A
10
1
2
4
5
6
7
8
9
▶▶ Recommended HDMI cable types
-- High-speed HDMI®/TM cable
-- High-speed HDMI®/TM Ethernet cable
SERVICE ONLY Port
-- This USB port is used only for services.
5V
0.9 A /
(USB Connector)
-- This terminal is used for connecting a HW Calibrator (an optional accessory).
-- A keyboard, mouse, or USB storage device can be connected.
10
CAUTION
Cautions When Using a USB Storage Device
• A USB storage device which has a built-in automatic recognition program or uses its own driver
might not be recognizable.
• Some USB storage devices may not be supported or may not work properly.
• It is recommended to use a USB hub or hard disk drive with power supplied. (If the power supplied
is not enough, the USB device may not be detected properly.)
5V
0.9 A /
(USB Connector)
-- Connect peripheral device to the USB input port.
-- To use USB 3.0, connect the A-B type USB 3.0 cable to the PC.
ENGLISH
3
Potential Equalization Conductor
-- Connect an equipotential plug.
DC-IN (19 - 24 V
) Port
-- Connect an AC/DC adapter.
-- The output of the enclosed adaptor is 19 V.
-- The product is designed to be used with adaptors of the output ranging between 19-24 V.
RS-232C Port
-- Connect the RS-232C terminal with an external device to control the monitor.
COMPOSITE IN Port
-- Input composite video signals.
S-VIDEO IN Port
-- Input S-Video signals.
DVI IN / DVI OUT Port
-- Input or output a digital video signal.
RGBS IN / COMPONENT IN Port
-- Input an analogue signal.
-- Use the DVI-I to D-SUB gender cable included with the product.
SDI IN / SDI OUT Port
-- Input or output a serial digital component signal.
HDMI IN Port
-- Input digital video signal.
-- Using a DVI to HDMI / DP (DisplayPort) to HDMI cable may cause compatibility issues.
Use a certified cable that displays the HDMI logo. The screen may not appear or a connection error
could occur if a non-certified cable is used.
NOTE
• All signal out terminals (SDI, DVI, etc.) output a signal when the power switch of the monitor is on. When the
power switch is off, no signal is outputted.
• This monitor supports the *Plug and Play feature.
* Plug and Play: A feature that allows you to add a device to your computer without the need for physical device
configuration or user intervention.
• The standard of the DVI and the SDI output terminals for transmitting a screen
-- DVI OUT: Connect a 5-meter cable to transmit a copied screen to a monitor.
-- SDI OUT: Connect a 100-meter cable (BELDEN 1694) to transmit a copied screen to a monitor.
9
Installing the Monitor
Cable connection and organize
ENGLISH
10
Before connecting the connectors, remove the back door as shown below.
1 Remove the back door by lifting it in the direction of the arrow. The back door is held in place with a magnet.
2 After installing the cables, tidy them up using the cable holders.
3 After tidying the cables, attach the back door and use the product.
Installing on the Wall
Install the monitor at least 100 mm away from the wall on each side of the monitor to ensure sufficient
ventilation. Detailed installation instructions can be obtained from your local dealer. Please refer to the manual to
install and set up a tilting wall mounting bracket.
ENGLISH
100 mm
100 mm
100 mm
100 mm
CAUTION
• When the back door is attached to the monitor, the monitor meets water resistance standards. Do not use the
monitor with the back door detached, as the water resistance capability is not guaranteed without the door.
To install the monitor to a wall, attach a wall mount plate (optional) to the back of the monitor.
Make sure that the wall mount plate (optional) is securely fixed to the monitor and to the wall.
1 Using screws longer than the standard length may damage the inside of the product.
2 A non-VESA standard screw may damage the product and cause the monitor to fall. LG Electronics is not
liable for any accidents relating to the use of non-standard screws.
11
Wall Mount (mm)
Standard screw
Required screws
Wall Mount Plate (optional)
100 x 100
M4 x L10
4
RW120
CAUTION
ENGLISH
• Disconnect the power cord first. Then move or install the monitor. There is risk of electric shock.
• Installing the monitor on the ceiling or on a slanted wall may result in the monitor falling off, which could lead
to injury. Use an authorized LG wall mount and contact the local dealer or qualified personnel.
• Applying excessive force when tightening screws may damage the monitor. Such damage is not covered by the
product warranty.
• Use the wall mounting bracket and screws that confirm to VESA standards. Damage caused by the use or
misuse of inappropriate components is not covered by the product warranty.
• When measured from the back of the monitor, the length of each installed screw must be 8 mm or less.
Wall mount plate
NOTE
•
•
•
•
•
•
The screws (M4 x L10) can be found fastened in the wall mount screw holes on the back of the monitor.
Use the screws specified by VESA standards.
The wall mount kit includes an installation manual and the necessary parts.
The wall mount plate is an optional item. You can obtain additional accessories from your local dealer.
The length of screws may differ depending on the wall mount. Be sure to use the proper length.
For more information, please refer to the manual for the wall mounting bracket.
Back of the monitor
Wall mount plate
Back of the monitor
Screw specifications
: M4 x L10
Max. 8 mm
12
Precautions for Connecting the Power Cord
ENGLISH
100-240 V ~
• Make sure to use the power cord that is provided in the product package. Connect the cord to a grounded
power outlet.
• If you need another power cord, please contact your local dealer or the nearest retail store.
13
USER SETTINGS
ENGLISH
Activating the Quick Menu
1 Press
2
3
4
to activate the LED Control Button. When the LED Control button is activated, press
Menu.
Among the LED Control Button, press
to move to the left or right or
Among the LED Control Button, press
to move to the left or right or
or
to set options.
In order to exit from the OSD Menu, press the LED Control Button
or select [Exit].
to show the OSD Quick
to move to the bottom or top.
to move to the bottom or top
Exit
: Ok
Input
Picture Mode
Gamma
Color Temp
All Settings
14
The applicable setting options are as shown below.
Closes the Quick Menu.
Explanation
[Input]
Selects the applicable input mode.
[Picture Mode]
Selects the [Picture Mode].
[Gamma]
• If the [Picture Mode] is not the [Custom] mode, [Gamma] and [Color Temp] will be deactivated.
Selects the screen's [Gamma].
[Color Temp]
Selects the screen's [Color Temp].
[All Settings]
Enters the All Settings menu.
NOTE
ENGLISH
Quick Menu Settings
[Exit]
CAUTION
• The Monitor OSD (On Screen Display) may differ from the description in the User Manual.
15
Quick Settings
1 Press
ENGLISH
2
3
4
5
to activate the LED Control Button. When the LED Control Button is activated, press
and select [All Settings]
to show the complete OSD Menu.
Among the LED Control Button, press
to move to the left or right or
to move to the bottom or top to
go to the [Quick Settings].
Configure the options following the instructions that appear in the bottom right corner.
To configure an upper menu or another item, press the LED Control Button
or press
to move to the settings.
In order to exit from the OSD Menu, press the LED Control Button
or press
.
Quick Settings
Quick Settings
Input
Brightness
100
>
Contrast
70
>
Hot key Settings
>
User Preset
>
Picture
General
Auto
Configuration
: Exit
16
/
: Move
/
: Ok
The applicable setting options are as shown below.
Explanation
Adjusts screen brightness.
NOTE
•
•
•
•
Press the button to toggle between [Turn on 'Brightness Stabilization']/[Turn off 'Brightness Stabilization'].
When [Brightness Stabilization] is [On] , the [Brightness] adjustment function is deactivated.
When [Brightness Stabilization] is [On], [SMART ENERGY SAVING] and [DFC] functions are deactivated.
When [Picture Mode] is set as [DICOM], or [Gamma] is set as [DICOM Gamma Curve] Setting, the [Brightness] adjustment function is deactivated.
[Contrast]
Adjusts the colour contrast of the screen.
[Hot key Settings]
Designate a hotkey for screen image settings. After setting the hotkey, use the hotkey in the LED Control Button to enable the set menu. ([PIP Size], [Mono], [Color Temp], [Gamma], [Black Stabilizer],
[Screen Zoom], [Off])
[Hotkey 1]
Select a function to use with [Hotkey 1].
[Hotkey 2]
Select a function to use with [Hotkey 2].
ENGLISH
[All Settings] > [Quick
Settings]
[Brightness]
17
[All Settings] > [Quick
Settings]
[User Preset]
ENGLISH
18
Explanation
User Preset allows the user to save or load up to 10 picture quality settings for multiple connected devices in each preset.
NOTE
• You can use User Preset to import or save items in [Picture Adjust] and [Color Adjust] of the [Picture] menu.
[User Name]
Allows the user to change and register a user name ([Preset 1] ~ [Preset 3], [User 1] ~ [User 7]) as the user wants.
The user can enter a user name to be registered by using the screen keyboard.
[Preset 1] ~ [Preset 3] are factory-set user names as samples and the user can change the names.
[Load User Settings]
Allows the user to change the picture quality settings by loading the User Preset settings.
[Save User Settings]
Saves the current picture quality settings in the corresponding User Preset.
[Preset 1] ~ [Preset 3] are factory-set values as samples and the user can change the values.
• [Preset 1]: Use this preset for bluish colour.
• [Preset 2]: Use this preset for greenish colour and brighter low-gradation.
• [Preset 3]: Use this preset to soften the red tone.
• [User 1] ~ [User 7]: Initial values are the same as the factory settings.
[Default User Settings]
Loads the initial basic picture settings.
[User Preset Reset]
Initializes User Preset settings.
• Initializes the existing user name and user settings to be restored to factory settings ([Preset 1] ~ [Preset 3], [User 1] ~ [User 7]).
Input
1 Press
3
4
5
Input
ENGLISH
2
to activate the LED Control Button. When the LED Control Button is activated, press
and select [All Settings] to
show the complete OSD Menu.
Among the LED Control Button, press
to move to the left or right or
to move to the bottom or top to go
to the [Input].
Configure the options following the instructions that appear in the bottom right corner.
To configure an upper menu or another item, press the LED Control Button
or press
to move to the settings.
In order to exit from the OSD Menu, press the LED Control Button
or press
.
Quick Settings
Input
Main Input List
Picture
HDMI >
Aspect Ratio
Full Wide >
PBP / PIP
General
>
PIP Size
Small >
Main/Sub Screen Change
Auto
Configuration
: Exit
/
: Move
/
: Ok
19
The applicable setting options are as shown below.
ENGLISH
[All Settings] > [Input]
[Main Input List]
Selects the input mode.
[Sub Input List]
PBP / PIP Connection
Explanation
[Sub]
-
[Main]
[Aspect Ratio]
-
O
O
-
-
-
O
O
-
-
-
O
-
O
O
O
O
O
O
O
-
O
O
O
-
-
O
O
-
-
-
-
-
O
O
-
-
-
-
-
O
O
-
-
-
NOTE
• The display may look the same for [Full Wide], [Original] and [Just Scan] options at the recommended resolution (1920 x 1080).
[Main Aspect Ratio]
[Full Wide]
Displays the image to fit the PBP / PIP screen, regardless of the video signal input.
20
-
O
Adjusts the aspect ratio of the screen. ([Full Wide], [Original], [Just Scan])
[Sub Aspect Ratio]
-
[Original]
[Full Wide]
Displays on the PBP / PIP screen in the aspect ratio of the video signal input.
Displays the image to fit the PBP / PIP screen, regardless of the video signal input.
[Original]
Displays on the PBP / PIP screen in the aspect ratio of the video signal input.
[All Settings] > [Input]
[PBP / PIP]
Displays screens of two input modes on a single monitor at the same time.
[PIP Size]
Explanation
Adjusts the size of PIP. ([Small], [Medium], [Large])
NOTE
ENGLISH
[Main/Sub Screen Change] Converts between the Main and the Sub in the [PBP / PIP] mode.
• If not using the [PBP / PIP] feature, [PIP Size], [Main/Sub Screen Change] are deactivated.
• You can connect a PC analogue (D-SUB) input source to the DVI-I input connector by using the DVI-I to D-SUB gender cable. In order to use a D-SUB input, use the DVI-I to D-SUB gender cable included in the box.
21
Picture
1 Press
ENGLISH
2
3
4
5
to activate the LED Control Button. When the LED Control Button is activated, press
and select [All Settings]
to show the complete OSD Menu.
Among the LED Control Button, press
to move to the left or right or
to move to the bottom or top to
go to the [Picture].
Configure the options following the instructions that appear in the bottom right corner.
To configure an upper menu or another item, press the LED Control Button
or press
to move to the settings.
In order to exit from the OSD Menu, press the LED Control Button
or press
.
Picture
Quick Settings
Input
Picture Mode
Custom >
Picture Adjust
>
Color Adjust
>
Configuration Adjust
>
Picture Reset
>
Picture
General
Auto
Configuration
: Exit
22
/
: Move
/
: Ok
The applicable setting options are as shown below.
[All Settings] > [Picture]
[Picture Mode]
Explanation
Allows the user to adjust each element. The colour mode of the main menu can be adjusted.
Mono (black and white) colour mode.
The standard RGB colour mode for monitors and printers.
The standard TV PAL colour mode for broadcasting.
The standard HDTV colour mode for broadcasting.
The standard TV NTSC colour mode for broadcasting.
A mode that optimizes the screen settings so you can view images for medical use.
Configures to the last calibrated (corrected) screen.
Configures to a previously calibrated (corrected) screen.
ENGLISH
[Custom]
[Mono]
[sRGB]
[EBU]
[REC709]
[SMPTE-C]
[DICOM]
[Calibration 1]
[Calibration 2]
NOTE
• The [Brightness Stabilization] function is operated in [Custom].
• [Calibration 2]: If you use Calibration after installing the TRUE COLOR PRO program, the applicable menu will be activated.
23
[All Settings] > [Picture]
[Picture Adjust]
[Brightness]
Explanation
Adjusts screen brightness.
NOTE
ENGLISH
•
•
•
•
[Contrast]
[Sharpness]
[Brightness Stabilization]
[SUPER RESOLUTION+]
[Black Level]
24
Press the button to toggle between [Turn on 'Brightness Stabilization']/[Turn off 'Brightness Stabilization'].
When [Brightness Stabilization] is [On] , the [Brightness] adjustment function is deactivated.
When [Brightness Stabilization] is [On], [SMART ENERGY SAVING] and [DFC] functions are deactivated.
When [Picture Mode] is set as [DICOM], or [Gamma] is set as [DICOM Gamma Curve] Setting, the [Brightness] adjustment function is deactivated.
Adjusts the colour contrast of the screen.
Adjusts the sharpness of the screen.
A function for maintaining a set brightness appropriate for treatment environments.
[On]
Automatically adjusts brightness.
[Off]
Deactivates the applicable function and the user can adjust the brightness.
[High]
Select this option for crystal clear images.
[Middle]
The optimized picture quality is displayed when a user wants images between low and high modes for comfortable viewing.
[Low]
The optimized picture quality is displayed when a user wants smooth and natural images.
[Off]
Select this option for the normal user experience. Deactivates the [SUPER RESOLUTION+] function.
Sets up the offset level. (HDMI only)
• Offset: as a reference for a video signal, this is the darkest colour the monitor can display.
[High]
Maintains the current screen contrast range.
[Low]
Reduces the black levels and increases the white levels of the current screen contrast range.
[All Settings] > [Picture]
[Picture Adjust]
[DFC]
[Black Stabilizer]
[Uniformity]
Explanation
Automatically adjusts brightness depending on the screen.
[Off]
Deactivates the [DFC] function.
Sets a response time for displayed pictures based on the movement of the picture on the screen.
In a normal environment, it is recommended that you set [Fast]. For images with a lot of motion, it is recommended that you set [Faster]. But, when [Faster] is set,
it may cause an afterimage.
[Faster]
Sets the response time to Faster.
[Fast]
Sets the response time to Fast.
[Normal]
Sets the response time to Normal.
[Off]
Does not use the response time improvement feature.
Adjusts the black level to clearly see objects on a dark screen.
Increasing the [Black Stabilizer] value brightens the low grey levels on the screen. (You can easily distinguish objects on a dark game screen.)
Reducing the [Black Stabilizer] value darkens the low grey levels and increases the dynamic contrast on the screen.
Automatically adjusts the brightness uniformity of the screen.
ENGLISH
[Response Time]
[On]
NOTE
• If [Uniformity] is activated, the screen may become darker.
[On]
Activates the [Uniformity] function.
[Off]
Deactivates the [Uniformity] function.
25
[All Settings] > [Picture]
[Color Adjust]
[Gamma]
ENGLISH
[Color Temp]
[6500K]
[7500K]
[9300K]
[Manual]
[Red]
[Green]
[Blue]
[Six Color]
[Configuration Adjust]
26
Explanation
Set your own gamma value. ([Gamma 1.8], [Gamma 2.0], [Gamma 2.2], [Gamma 2.4], [Gamma 2.6], [DICOM Gamma Curve])
Higher gamma settings mean a darker image is displayed or vice versa.
Set your own colour temperature. ([Custom], [6500K], [7500K], [9300K], [Manual])
[Custom]
Users can customize the red, green and blue colours.
[Horizontal] [Vertical]
[Clock] [Phase]
Indicates the screen colour with a 6500K red colour temperature.
Sets the screen colour between red and blue with a 7500K colour temperature.
Indicates the screen colour with 9300K blue colour temperature.
Adjusts the colour temperature in 500K increments. (However, supports 9300K instead of 9500K)
You can customize the picture colour using Red, Green and Blue colours.
Meets the user requirements for colours by adjusting the hue and saturation of the six colours (red, green, blue, cyan, magenta and yellow) and then saving the
settings.
[Hue]
Adjusts the tint of the screen colours.
[Saturation]
The lower the screen's colour sharpness value, the less sharper and brighter the colours become. The higher the value, the sharper and darker
the colours become.
Adjusts the position of the screen.
Improves the sharpness and stability of the screen.
[All Settings] > [Picture]
Explanation
[Resolution]
A user can set the desired resolution. This option is available only when the screen resolution of the computer is set as below (only for the D-SUB).
NOTE
ENGLISH
[Picture Reset]
• When the resolution selected by a user is different from the resolution outputted by the PC per computer, the function will be deactivated.
[1024 x 768], [1280 x 768], [1360 x 768], [1366 x 768], [Off]
[1280 x 960], [1600 x 900], [Off]
[1440 x 900], [1600 x 900], [Off]
Returns colour to the default settings.
27
General
1 Press
ENGLISH
2
3
4
5
to activate the LED Control Button. When the LED Control Button is activated, press
and select [All Settings] to
show the complete OSD Menu.
Among the LED Control Button, press
to move to the left or right or
to move to the bottom or top to go
to the [General].
Configure the options following the instructions that appear in the bottom right corner.
To configure an upper menu or another item, press the LED Control Button
or press
to move to the settings.
In order to exit from the OSD Menu, press the LED Control Button
or press
.
General
Language
Quick Settings
Input
English >
SMART ENERGY SAVING
Off >
HW Calibration
Off >
RS-232C
>
LED Control Button
Picture
General
Auto
Configuration
Off >
Hot key Settings
>
User Preset
>
Auto Screen Off
Off >
OSD Lock
Off >
Information
>
Reset
>
: Exit
28
20Sec Time Out >
DVI Power Supply
/
: Move
/
: Ok
The applicable setting options are as shown below.
[All Settings] > [General]
Explanation
Sets the menu screen to the desired language.
[SMART ENERGY SAVING]
Conserve energy by using luminance compensation algorithm.
[High]
Saves energy using the high-efficiency [SMART ENERGY SAVING] feature.
[HW Calibration]
[RS-232C]
[Low]
Saves energy using the low-efficiency [SMART ENERGY SAVING] feature.
[Off]
Disables the [SMART ENERGY SAVING] function.
[RS-232C] and the [HW Calibration] cannot be used at the same time.
[On]
The HW Calibration function will operate.
[Off]
The HW Calibration function will be turned off.
[RS-232C] and the [HW Calibration] cannot be used at the same time.
[Serial Port]
The [RS-232C] function will be operated or turned off.
[Set ID]
Adjusts [Set ID]. (The scope of adjustment: 1-10)
[LED Control Button]
Adjusts the ON time of the Control Button. ([Always On], [20Sec Time Out], [10Sec Time Out], [5Sec Time Out])
[DVI Power Supply]
Supplies power to a device used by connecting to a DVI input terminal in the form of dongle without power.
[Hot key Settings]
ENGLISH
[Language]
[On]
Activates the [DVI Power Supply] function.
[Off]
Deactivates the [DVI Power Supply] function.
Designate a hotkey for screen image settings. After setting the hotkey, use the hotkey in the LED Control Button to enable the set menu. ([PIP Size], [Mono], [Color Temp], [Gamma], [Black
Stabilizer], [Screen Zoom], [Off])
[Hotkey 1]
Select a function to use with [Hotkey 1].
[Hotkey 2]
Select a function to use with [Hotkey 2].
29
[All Settings] > [General]
[User Preset]
Explanation
User Preset allows the user to save or load up to 10 picture quality settings for multiple connected devices in each preset.
NOTE
ENGLISH
• You can use User Preset to import or save items in [Picture Adjust] and [Color Adjust] of the [Picture] menu.
[User Name]
Allows the user to change and register a user name ([Preset 1] ~ [Preset 3], [User 1] ~ [User 7]) as the user wants.
The user can enter a user name to be registered by using the screen keyboard.
[Preset 1] ~ [Preset 3] are factory-set user names as samples and the user can change the names.
[Load User Settings]
Allows the user to change the picture quality settings by loading the User Preset settings.
[Save User Settings]
[Default User Settings]
Saves the current picture quality settings in the corresponding User Preset.
[Preset 1] ~ [Preset 3] are factory-set values as samples and the user can change the values.
• [Preset 1]: Use this preset for bluish colour.
• [Preset 2]: Use this preset for greenish colour and brighter low-gradation.
• [Preset 3]: Use this preset to soften the red tone.
• [User 1] ~ [User 7]: Initial values are the same as the factory settings.
Loads the initial basic picture settings.
[User Preset Reset]
[Auto Screen Off]
30
Initializes User Preset settings.
• Initializes the existing user name and user settings to be restored to factory settings ([Preset 1] ~ [Preset 3], [User 1] ~ [User 7]).
Automatically turns off the screen when there is no monitor signal for a set time period.
[On]
Activates [Auto Screen Off] function.
[Off]
Deactivates [Auto Screen Off] function.
[All Settings] > [General]
[OSD Lock]
Explanation
NOTE
• Deactivates all functions except the [Quick Settings] menu and [Input] menu's [Input List], [Aspect Ratio] and [PBP/ PIP] functions, and the [General] menu's [OSD Lock] and [Information]
functions.
[Information]
Displays the total power on time, serial number and resolution information.
[Reset]
[Do you want to reset your settings?]
[No]
[Yes]
ENGLISH
A function for restricting menu configuration and adjustment.
[On]
Turns on [OSD Lock].
[Off]
Turns off [OSD Lock].
Cancels the selection.
Restores the screen settings to the default settings when your monitor was first purchased.
31
Auto Configuration
1 Press
ENGLISH
2
3
4
5
to activate the LED Control Button. When the LED Control Button is activated, press
and select [All Settings] to
show the complete OSD Menu.
Among the LED Control Button, press
to move to the left or right or
to move to the bottom or top to go
to the [Auto Configuration].
Configure the options following the instructions that appear in the bottom right corner.
To configure an upper menu or another item, press the LED Control Button
or press
to move to the settings.
In order to exit from the OSD Menu, press the LED Control Button
or press
.
Auto Configuration
Do you want to Auto Configuration?
Quick Settings
No
Yes
Input
Picture
General
Auto
Configuration
: Exit
The applicable setting options are as shown below.
[All Settings]> [Auto Configuration]
[Do you want to Auto Configuration?]
32
Explanation
[No]
Cancels the selection.
[Yes]
Automatically sets screen to optimal settings.
/
: Move
/
: Ok
TROUBLESHOOTING
• Check if the power cord is correctly plugged into the power outlet.
Is the power indicator on?
• Check the power cable connection and turn on the power switch.
Is the power indicator displaying as green?
• Check if the input setting is correct. (
Is the [Out of Range] message being displayed?
Is the [No Signal] message displayed?
• This occurs when signals transferred from the PC (graphics card) are out of the horizontal or vertical frequency range of the monitor. Please see the <Product
Specification> section of this manual to set the appropriate frequency.
• This is displayed when the signal cable between the PC and the monitor is missing or disconnected. Check the cable and reconnect it.
The screen retains an image.
Does image sticking occur even when the monitor is
turned off?
• Displaying a still image for a prolonged time may cause damage to the screen, resulting in the retention of the image.
• To extend the lifetime of the monitor, use a screensaver.
ENGLISH
Nothing is displayed on the screen.
Is the monitor's power cord plugged in?
> [All Settings] > [Input])
The screen is unstable and shakes. / There are shadowy traces left on the screen.
Did you select the appropriate resolution?
• If the selected resolution is HDMI 1080i 60/50 Hz (interlaced), the screen may be flickering. Change the resolution to 1080p or the recommended resolution.
33
NOTE
ENGLISH
• Vertical Frequency: In order to display an image, the screen must be refreshed dozens of times per second, like a fluorescent lamp. The number of times the screen is refreshed per second is called vertical frequency, or refresh rate,
and is represented by Hz.
• Horizontal Frequency: The time it takes to display one horizontal line is called the horizontal cycle. If 1 is divided by the horizontal interval, the result is the number of horizontal lines displayed per second. This is called horizontal
frequency and is represented by kHz.
• Check if the graphics card's resolution or frequency is within the range allowed by the monitor and in Windows set it to the recommended (optimal) resolution in Control Panel > Display > Settings. (May differ depending on your
operating system (OS).)
• Not setting the video card to the recommended (optimal) resolution may result in blurred text, a dimmed screen, a truncated display area or misalignment of the display.
• The setting methods may be different depending on the computer or operating system, and some resolutions may not be available depending on the performance of the graphics card. If this is the case, contact the manufacturer of
the computer or graphics card for assistance.
• Normal graphics cards do not support 1920 x 1080 resolution. If the resolution cannot be displayed, contact the manufacturer of your graphics card.
The display colour is abnormal.
Does the display appear discoloured (16 colours)?
Does the display colour appear unstable or
monochrome?
Are there spots on the screen?
• Set the number of colours to 24 bits (true colours) or higher: In Windows Control Panel > Display > Settings > Colour Quality (May differ depending on your operating
system.)
• Check if the signal cable is connected properly. Reconnect the cable or reinsert the PC's graphics card.
• When using the monitor, pixilated spots (red, green, blue, white or black) may appear on the screen. This is normal for an LCD screen. It is not an error, nor is it related to the
monitor's performance.
The 'Unknown Monitor' message appears when the monitor is connected.
Did you install the monitor driver?
• Install the enclosed monitor driver which is provided with the monitor or go to LG Electronics homepage (www.lg.com) to download and install the monitor driver.
• Check whether the plug & play function is supported by referring to the graphics card user manual.
The image is displayed abnormally.
Does the screen area appear abnormal?
Do you see vertical lines on the screen?
Does the screen display horizontal noise, or does the
text appear blurred?
34
• If you want to automatically configure display images to optimal settings, enter the [Auto Configuration] function and select [Yes].
PRODUCT SPECIFICATIONS
LCD Screen
Resolution
Type
TFT (Thin Film Transistor)
LCD (Liquid Crystal Display) Screen
Pixel Pitch
0.3114 mm x 0.3114 mm
Max Resolution
Recommended Resolution
Video Signal
Input Connector
Output Connector
Power Sources
AC-DC Adaptor
1920 x 1080 @ 60 Hz
Horizontal Frequency
30 kHz - 83 kHz
Vertical Frequency
56 Hz - 75 Hz
Potential Equalization Conductor, DC-IN (19 - 24 V
), RS-232C, COMPOSITE IN, S-VIDEO IN, DVI IN, RGBS IN, COMPONENT IN, SDI IN, HDMI IN, SERVICE ONLY, USB (
USB (
)
DVI OUT, SDI OUT
Power Rating
19 - 24 V
6.32 - 5.0 A
Power Consumption
ENGLISH
In order to improve the product, specifications may change without notice.
The ~ symbol means alternating current, and the symbol
means direct current.
5V
0.9 A),
Max. 120 W
Off Mode: ≤ 0.3 W
DA-120D19 type, manufactured by Asian Power Devices Inc. (APD)
Input: 100-240 V~ 50-60 Hz, 1.8-0.7 A
Output: 19 V
6.32 A
Classification by protection type against Electric Shock: Class equipment
NOTE
-- Connect an AC/DC adapter.
-- The output of the enclosed adaptor is 19 V.
-- The product is designed to be used with adaptors of the output ranging between 19-24 V.
35
Environmental Conditions
ENGLISH
Operating Conditions
Temperature
0°C to 40°C
Storing Conditions
Humidity
Pressure
Temperature
0% to 80%
700 hPa to 1060 hPa
-20°C to 60°C
Humidity
Pressure
0% to 85%
500 hPa to 1060 hPa
Dimensions (mm)
Monitor Size (Width x Height x Depth)
656.4 x 412.9 x 62.2
Weight (Without Packaging) (kg)
36
7.7
Preset Mode
Input Timing (Video)
D-SUB / DVI / HDMI
Horizontal
Frequency (kHz)
Vertical
Frequency (Hz)
Polarity (H/V)
720 x 400
31.468
70.08
-/+
640 x 480
31.469
59.94
-/-
640 x 480
37.5
75
-/-
720 x 480
31.47
59.94
-/-
800 x 600
37.879
60.317
+/+
800 x 600
46.875
75.0
+/+
1024 x 768
48.363
60.0
-/-
1024 x 768
60.023
75.029
+/+
1152 x 864
67.500
75.000
+/+
1280 x 720
1280 x 800
1280 x 1024
1280 x 1024
1400 x 1050
1440 x 900
1600 x 900
1680 x 1050
1920 x 1080
45
49.306
63.981
79.976
64.744
55.469
60.00
65.290
67.50
60
59.910
60.02
75.025
59.948
59.901
60.00
59.954
60
+/+
+/+/+
+/+
+/+/+/+
-/+
+/+
Remarks
HDMI only
Vertical
Frequency (Hz)
59.94/60
59.94/60
50
50
59.94/60
50
59.94/60
59.94/60
50
50
29.97/30
HDMI
SDI
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
Remarks
ENGLISH
Preset Mode
Vertical
dimensions
480i
480p
576p
576i
720p
720p
1080i
1080p
1080i
1080p
1080p
37
Input Timing (Component)
Power indicator
720 x 480
720 x 480
Horizontal
Frequency (kHz)
15.730
15.750
Vertical
Frequency (Hz)
59.940
60.000
720 x 480
31.470
59.940
720 x 480
31.500
60.000
720 x 576
15.625
50.000
Resolution
ENGLISH
720 x 576
31.250
50.000
1280 x 720
44.960
59.940
1280 x 720
45.000
60.000
1280 x 720
37.500
50.000
1920 x 1080
33.720
59.940
1920 x 1080
33.750
60.000
1920 x 1080
28.125
50.000
1920 x 1080
56.250
50.000
1920 x 1080
67.432
59.940
1920 x 1080
67.500
60.000
Input Timing (S-Video, Composite)
• This monitor supports the NTSC, PAL.
38
Mode
On Mode
LED Colour
Green
EXTERNAL CONTROLLER SETUP
Figure 1: RS-232C Connection Diagram
Use an RS-232C cable to remotely control the monitor (see Figure 1).
RXD
TXD
DTR
GND
DSR
RTS
CTS
2
3
4
5
6
7
8
PC
RS-232C
(PC)
2
3
4
5
6
7
8
RXD
TXD
DTR
GND
DSR
RTS
CTS
5
1
ENGLISH
The actual product may differ from the picture shown.
Connect the RS-232C (serial connector) of the PC to the RS-232C IN connector at the back of the monitor.
Purchase a cable to connect the RS-232C connectors, as the cable is not provided as an accessory.
9
6
Monitor
* There are no connections to Pin 1 and Pin 9.
(Monitor)
39
Set ID Function
ENGLISH
This function allows you to assign a unique ID to the monitor to control it remotely from your PC.
Please refer to the "Transmission/Reception Protocol".
1 Press the
button.
2 Use the , , , buttons to select [General]. Then press the
button.
3 Use the , , , buttons to select [Set ID]. Then press the
button.
4 Select a [Set ID] to assign. Then press the
button. The [Set ID] can be a value from 1 to 10.
5 In order to exit from the OSD Menu, press the LED Control Button
or press
.
Communication Parameters
•
•
•
•
•
•
40
Baud rate: 9600 bps (UART)
Data length: 8 bits
Parity bit: None
Stop bit: 1 bit
Communication code: ASCII code
Crossed (reverse) cable used.
Command Reference List
Command
Power
Screen Mute
Input select ([Main])
Input select ([Sub])
[Aspect Ratio] ([Main])
[Aspect Ratio] ([Sub])
[PBP / PIP]
[PIP Size]
[Main/Sub Screen Change]
[Picture Mode]
[Brightness]
[Contrast]
[Sharpness]
[Brightness Stabilization]
Command1
Command2
k
k
k
k
k
k
k
k
m
d
k
k
k
m
a
d
b
y
c
o
n
p
a
x
h
g
k
b
Data
(Hexadecimal)
00 ~ 01
00 ~ 01
00 ~ 06
00 ~ 06
00 ~ 02
00 ~ 01
00 ~ 05
00 ~ 02
01
00 ~ 08
00 ~ 64
00 ~ 64
00 ~ 64
00 ~ 01
15. [SUPER RESOLUTION+]
m
c
00 ~ 03
16.
17.
18.
19.
20.
m
m
m
m
m
d
f
g
h
i
00 ~ 01
00 ~ 01
00 ~ 03
00 ~ 64
00 ~ 01
[Black Level]
[DFC]
[Response Time]
[Black Stabilizer]
[Uniformity]
21.
22.
23.
24.
25.
26.
27.
28.
29.
30.
31.
32.
33.
[Gamma]
[Color Temp]
Red Gain
Green Gain
Blue Gain
[Language]
[SMART ENERGY SAVING]
[LED Control Button]
[DVI Power Supply]
[Auto Screen Off]
[OSD Lock]
[Reset]
[Auto Configuration]
Command1
Command2
m
k
j
j
j
f
m
m
m
m
k
f
j
j
u
w
y
z
i
k
l
m
n
m
k
u
Data
(Hexadecimal)
00 ~ 05
00 ~ 04
00 ~ 64
00 ~ 64
00 ~ 64
00 ~ 10
00 ~ 02
00 ~ 03
00 ~ 01
00 ~ 01
00 ~ 01
00 ~ 02
01
ENGLISH
01.
02.
03.
04.
05.
06.
07.
08.
09.
10.
11.
12.
13.
14.
Command
41
Transmission/Reception Protocol
Error Acknowledgment
[Command2][ ][Set ID][ ][NG][Data][x]
Transmission
ENGLISH
[Command1][Command2][ ][Set ID][ ][Data][Cr]
[Command 1]: j, k, m, x
[Command 2]: This command is used to control the monitor.
[Set ID]: U sed to identify the monitor being controlled. [Set ID] can be assigned to each monitor under [General]
in the Settings Menu.
A value from 1 to 10 can be assigned. By selecting '0' for the [Set ID] value in the protocol format, you can
control all connected monitors.
* The value is displayed as base 10 on the OSD menu and used as base 16 (0x00 - 0x63) in the transmission/
reception protocol for remote control.
[Data]: Transmits a setting value (Data) required for the command described previously. (base 16)
When the Data ‘FF’ is sent, the setting value corresponding to the specific command is read (Data read mode).
[Cr]: Carriage return, which is ‘0x0D’ in ASCII code.
[ ]: Space, which is ‘0x20’ in ASCII code.
OK Acknowledgment
[Command2][ ][Set ID][ ][OK][Data][x]
When the Data has been successfully received, the monitor sends an ACK response signal in the above format. The
Data showing the current state is received in the Data read mode. The Data from the PC is simply returned in the
Data write mode.
42
When the set receives an abnormal piece of Data for an unsupported function or there is a communication error, it
returns ACK in the format above.
Data 00
: Illegal code
Actual Data Structure (Base 16
Base 10)
• See the table below when inserting a base-16 value in [Data].
• The channel setup command (ma) uses a 2-byte base-16 value ([Data]) for channel number input.
00: Step 0
01: Step 1 (Set ID 1)
...
0A: Step 10 (Set ID 10)
...
0F: Step 15 (Set ID 15)
10: Step 16 (Set ID 16)
...
32: Step 50 (Set ID 50)
33: Step 51 (Set ID 51)
...
63: Step 99 (Set ID 99)
...
C7: Step 199
C8: Step 200
...
* Commands may work differently depending on the model and signal.
FE: Step 254
FF: Step 255
...
01 00: Step 256
...
27 0E: Step 9998
27 0F: Step 9999
...
01. Power (Command: k a)
04. Input select ([Sub]) (Command: k y)
▶▶ Controls the On/Off of the power supply to the monitor.
▶▶ Controls the input mode of the Sub.
Transmission [k][a][ ][Set ID][ ][Data][Cr]
01: Power On
Ack [a][ ][Set ID][ ][OK/NG][Data][x]
02. Screen Mute (Command: k d)
▶▶ Controls the On/Off of the screen of the monitor.
01: Screen Mute On
05. [Aspect Ratio] ([Main]) (Command: k c)
▶▶ Adjusts the Aspect Ratio of the Main.
Ack [d][ ][Set ID][ ][OK/NG][Data][x]
Transmission [k][c][ ][Set ID][ ][Data][Cr]
Data
00 : [Full Wide]
02 : [Just Scan]
03. Input select ([Main]) (Command: k b)
▶▶ Controls the input mode of the Main.
Transmission [k][b][ ][Set ID][ ][Data][Cr]
Data
00 : D-SUB
02 : DVI
04 : Component
06 : S-Video
01 : SDI
03 : HDMI
05 : Composite
Ack [y][ ][Set ID][ ][OK/NG][Data][x]
Transmission [k][d][ ][Set ID][ ][Data][Cr]
Data 00: Screen Mute Off
Data
00 : D-SUB
02 : DVI
04 : Component
06 : S-Video
ENGLISH
Data 00: Power Off
Transmission [k][y][ ][Set ID][ ][Data][Cr]
01 : [Original]
Ack [c][ ][Set ID][ ][OK/NG][Data][x]
01 : SDI
03 : HDMI
05 : Composite
Ack [b][ ][Set ID][ ][OK/NG][Data][x]
43
06. [Aspect Ratio] ([Sub]) (Command: k o)
09. [Main/Sub Screen Change] (Command: m a)
▶▶ Adjusts the Aspect Ratio of the Sub.
▶▶ Controls the Swap in the PBP mode.
Transmission [k][o][ ][Set ID][ ][Data][Cr]
ENGLISH
00 : [Full Wide]
Transmission [m][a][ ][Set ID][ ][Data][Cr]
01 : [Original]
Data 01 : Main/Sub Screen exchange
Ack [a][ ][Set ID][ ][OK/NG][Data][x]
Ack [o][ ][Set ID][ ][OK/NG][Data][x]
07. [PBP / PIP] (Command: k n)
10. [Picture Mode] (Command: d x)
▶▶ Controls the PBP/PIP mode.
▶▶ Controls the Picture Mode.
Transmission [d][x][ ][Set ID][ ][Data][Cr]
Transmission [k][n][ ][Set ID][ ][Data][Cr]
Data
00 : Off
02: PIP_LT
04: PIP_LB
01: PBP
03: PIP_RT
05: PIP_RB
Ack [n][ ][Set ID][ ][OK/NG][Data][x]
Data
00 : [Custom]
02 : [sRGB]
01 : [Mono]
03 : [EBU]
04 : [REC709]
05 : [SMPTE-C]
06 : [DICOM]
07 : [Calibration 1]
08 : [Calibration 2]
Ack [x][ ][Set ID][ ][OK/NG][Data][x]
08. [PIP Size] (Command: k p)
▶▶ Adjusts the size of PIP.
11. [Brightness] (Command: k h)
Transmission [k][p][ ][Set ID][ ][Data][Cr]
Data
00 : [Small]
02 : [Large]
Ack [p][ ][Set ID][ ][OK/NG][Data][x]
44
▶▶ Adjusts screen brightness.
01 : [Medium]
Transmission [k][h][ ][Set ID][ ][Data][Cr]
Data Min : 00 - Max : 64
Ack [h][ ][Set ID][ ][OK/NG][Data][x]
12. [Contrast] (Command: k g)
15. [SUPER RESOLUTION+] (Command: m c)
▶▶ Adjusts the colour contrast of the screen.
▶▶ Controls the SUPER RESOLUTION+ function.
Transmission [k][g][ ][Set ID][ ][Data][Cr]
Transmission [m][c][ ][Set ID][ ][Data][Cr]
Data 00 : [High]
02 : [Low]
Ack [g][ ][Set ID][ ][OK/NG][Data][x]
01 : [Middle]
03 : [Off]
ENGLISH
Data Min : 00 - Max : 64
Ack [c][ ][Set ID][ ][OK/NG][Data][x]
13. [Sharpness] (Command: k k)
16. [Black Level] (Command: m d)
▶▶ Adjusts the sharpness of the screen.
▶▶ Controls the Offset level. (HDMI only)
Transmission [k][k][ ][Set ID][ ][Data][Cr]
Transmission [m][d][ ][Set ID][ ][Data][Cr]
Data Min : 00 - Max : 64
Data 00 : [High]
Ack [k][ ][Set ID][ ][OK/NG][Data][x]
01 : [Low]
Ack [d][ ][Set ID][ ][OK/NG][Data][x]
14. [Brightness Stabilization ] (Command: m b)
17. [DFC] (Command: m f)
▶▶ Controls the Brightness Stabilization function.
▶▶ Controls the DFC function.
Transmission [m][b][ ][Set ID][ ][Data][Cr]
Data 00 : [Off]
Ack [b][ ][Set ID][ ][OK/NG][Data][x]
01 : [On]
Transmission [m][f][ ][Set ID][ ][Data][Cr]
Data 00 : [On]
01 : [Off]
Ack [f][ ][Set ID][ ][OK/NG][Data][x]
45
18. [Response Time] (Command: m g)
21. [Gamma] (Command: m j)
▶▶ Controls the Response Time.
▶▶ Adjusts the Gamma settings.
Transmission [m][g][ ][Set ID][ ][Data][Cr]
ENGLISH
Data 00 : [Faster]
02 : [Normal]
Transmission [m][j][ ][Set ID][ ][Data][Cr]
01 : [Fast]
03 : [Off]
Ack [g][ ][Set ID][ ][OK/NG][Data][x]
Data 00 : [Gamma 1.8]
02 : [Gamma 2.2]
04 : [Gamma 2.6]
01 : [Gamma 2.0]
03 : [Gamma 2.4]
05 : [DICOM Gamma Curve]
Ack [j][ ][Set ID][ ][OK/NG][Data][x]
19. [Black Stabilizer] (Command: m h)
▶▶ Controls the Black Sharpness Optimization function.
22. [Color Temp] (Command: k u)
▶▶ Adjusts the colour Temp.
Transmission [m][h][ ][Set ID][ ][Data][Cr]
Transmission [k][u][ ][Set ID][ ][Data][Cr]
Data Min : 00 - Max : 64
Data
00 : [Custom]
02 : [7500K]
04 : [Manual]
Ack [h][ ][Set ID][ ][OK/NG][Data][x]
20. [Uniformity] (Command: m i)
▶▶ Controls the Uniformity function.
Ack [u][ ][Set ID][ ][OK/NG][Data][x]
Transmission [m][i][ ][Set ID][ ][Data][Cr]
Data 00 : [On]
Ack [i][ ][Set ID][ ][OK/NG][Data][x]
01 : [Off]
23. Red Gain (Command: j w)
▶▶ Adjusts the red.
Transmission [j][w][ ][Set ID][ ][Data][Cr]
Data Min : 00 - Max : 64
Ack [w][ ][Set ID][ ][OK/NG][Data][x]
46
01 : [6500K]
03 : [9300K]
24. Green Gain (Command: j y)
27. [SMART ENERGY SAVING] (Command: m k)
▶▶ Adjusts the green.
▶▶ Adjusts the SMART ENERGY SAVING.
Transmission [j][y][ ][Set ID][ ][Data][Cr]
Ack [y][ ][Set ID][ ][OK/NG][Data][x]
Data 00 : [High]
02 : [Off]
01 : [Low]
ENGLISH
Data Min : 00 - Max : 64
Transmission [m][k][ ][Set ID][ ][Data][Cr]
Ack [k][ ][Set ID][ ][OK/NG][Data][x]
25. Blue Gain (Command: j z)
▶▶ Adjusts the blue.
Transmission [j][z][ ][Set ID][ ][Data][Cr]
28. [LED Control Button] (Command: m l)
▶▶ Adjusts the LED ON time of the Control Button.
Transmission [m][l][ ][Set ID][ ][Data][Cr]
Data Min : 00 - Max : 64
Ack [z][ ][Set ID][ ][OK/NG][Data][x]
26. [Language] (Command: f i)
▶▶ Adjusts the language of the Menu screen.
Transmission [f][i][ ][Set ID][ ][Data][Cr]
Data 00 : [Always On]
02 : [10Sec Time Out]
01 : [20Sec Time Out]
03 : [5Sec Time Out]
Ack [l][ ][Set ID][ ][OK/NG][Data][x]
29. [DVI Power Supply] (Command: m m)
▶▶ Controls the DVI Power Supply function.
English - Korean (17 languages)
Ack [i][ ][Set ID][ ][OK/NG][Data][x]
Transmission [m][m][ ][Set ID][ ][Data][Cr]
Data 00 : [On]
01 : [Off]
Ack [m][ ][Set ID][ ][OK/NG][Data][x]
47
30. [Auto Screen Off] (Command: m n)
33. [Auto Configuration] (Command: j u)
▶▶ Adjusts the time to automatically turn the screen off when there is no monitor signal for a set period of time.
▶▶ Performs the Auto Configuration.
Transmission [m][n][ ][Set ID][ ][Data][Cr]
ENGLISH
Data 00 : [On]
Transmission [j][u][ ][Set ID][ ][Data][Cr]
01 : [Off]
Ack [n][ ][Set ID][ ][OK/NG][Data][x]
Ack [u][ ][Set ID][ ][OK/NG][Data][x]
31. [OSD Lock] (Command: k m)
▶▶ Controls the OSD Lock function.
Transmission [k][m][ ][Set ID][ ][Data][Cr]
Data 00 : [Off]
01 : [On]
Ack [m][ ][Set ID][ ][OK/NG][Data][x]
32. [Reset] (Command: f k)
▶▶ Controls the Reset operation.
Transmission [f][k][ ][Set ID][ ][Data][Cr]
Data
00: [Picture Reset]
02: [User Preset Reset]
Ack [k][ ][Set ID][ ][OK/NG][Data][x]
48
Data 01 : [Auto Configuration]
01: Factory Reset
WARNING: This equipment is compliant with Class A of CISPR 32. In a residential environment this equipment may
cause radio interference.
Read the user manual (CD) carefully and keep it at hand. The product label contains necessary information for afterservice.
Model
Serial No.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising