LG | A9ADVANCED | Owner's Manual | LG A9ADVANCED Owner’s Manual

LG A9ADVANCED Owner’s Manual
OWNER'S Manual
A9
Make sure to read the "Safety Cautions" carefully before starting to use this product.
Please keep this Owner's Manual within easy reach of the user.
As the product is only intended for domestic use such as household cleaning, it must not be used for commercial,
experimental or industrial purposes.
Make sure to fully charge the product's battery before first use of the product after purchasing it.
MFL69883617
www.lg.com
Copyright © 2018 - 2019 LG Electronics Inc. All Rights Reserved.
Table of Contents
This User's Manual may contain images or contents
that differ slightly to the purchased product.
Safety Cautions..................................................... 04
Package information........................................... 12
Installation............................................................ 14
Installing the floor standing charging station........................................................14
Installing the wall-mount station.................................................................................15
Uninstalling the station.....................................................................................................15
Storage of the combination tool and crevice tool...............................................16
Storage of the Mop Nozzle..............................................................................................16
Storage of the Mop Pads..................................................................................................16
How to Use............................................................... 17
Note about using the product........................................................................................17
Using the Product.................................................................................................................17
Charging the Product..........................................................................................................18
Power / Suction Strength button.................................................................................18
Using the nozzles..................................................................................................................19
Maintenance........................................................... 23
Cleaning the Dustbin...........................................................................................................23
Cleaning the Filters..............................................................................................................23
Cleaning the Hard Floor Power Drive Nozzle®/
Multi-surface Power Drive Nozzle®............................................................................25
Cleaning the Bedding Power Punch............................................................................25
Cleaning of the Mop Nozzle............................................................................................26
Points to check before contacting
customer service.................................................. 27
Disposal information.......................................... 29
Disposal of old products not related with the
purchase of a new product......................................................................................................29
Product specifications....................................... 29
Rev.04_071919
03
Safety CAUTIONS
The following cautions are intended to protect you from unexpected risk or property loss by ensuring safe
and correct usage of the product.
Cautions are categorized into 'Warning' and 'Caution', which mean:
Pictograms are designed to draw attention to matters and uses that may pose a risk to
the user. Make sure to carefully read any item marked with this symbol and comply with
it to prevent any risk.
WARNING
Failure to comply with this warning may result in serious damage, injury or even death to
the user.
CAUTION
Failure to comply with this warning may result in damage to the product or moderate
injury to the user.
WARNING
Technical Safety
••This appliance is not intended for use by persons (including children) with
reduced physical, sensory or mental capabilities, or lack of experience and
knowledge, unless they have been given supervision or instruction concerning
use of the appliance by a person responsible for their safety. Children should
be supervised to ensure that they do not play with the appliance.
••If the power supply cord is damaged, it must be replaced by an LG Electronics
service center or dealer in order to avoid a potential hazard.
••Do not allow children to play with or hang on the appliance.
••Do not use the appliance on a wet surface.
••Place the cords from other appliances out of the area to be cleaned.
04
Battery
••Never use the battery, adapter, and the charging station from other appliances
with this appliance. Use only the battery and the charging station provided by
LG Electronics.
••Never use the battery, adapter, and the charging station from this appliance
with other appliances.
••Do not use the battery if it is leaking or has changed shape. If skin or eyes
come into contact with battery fluid, thoroughly wash the affected area
immediately with clean water and seek medical attention.
••Replace the battery when it is no longer able to hold a charge.
••Refer to the Charging section instructions for the method of replacing the
battery.
••When disposing of this appliance, make sure to remove the battery from the
appliance.
••Follow all local ordinances and regulations when handling or disposing of the
battery.
Battery Specifications
••One or two batteries are provided, the number of batteries varies depending
on the model purchased.
Model Name
EAC63382***
Type
Rechargeable Lithium-ion Battery
Rated Capacity
25.55 V
, 2000 mAh
05
Installation and Usage
Do not install, charge or store the product where it may be exposed to water, rainfall or severe moisture. Do
not use the product in any outdoor location, workshop or garage environment.
•• Such conditions will leave the product vulnerable to fire when charging the battery.
•• Please install, charge or store the product in a well-ventilated place.
Make sure to avoid places where there is a risk of leakage of flammable gas, industrial oil or metallic dust.
•• It may cause product malfunction or damage.
If you intend to use the charging station by "standing" it vertically (standing type), make sure to secure it
to the wall with the appropriate type of screws .
•• Otherwise, the charging station or product may slant and become damaged or cause property damage or injury.
Please place the charging station on an even surface.
•• Otherwise, the product may fall and sustain damage or cause an injury.
If you intend to mount the charging station on a wall (wall-mounted type), make sure to secure it tightly to
the wall using the appropriate type of screws.
•• Failure to do so may damage the product and/or cause an injury.
Please use the anchoring screws only when the wall is made of concrete or is solid enough.
•• If the Station mounting is performed on an unsuitable wall it may cause injury and damage the property or product.
Never install the charging station on a wall with any piping (gas, water, air) or power cables or wires behind
it.
•• There is a risk of injury from electric shock, fire or flooding.
Do not use or store the product at temperatures below 5 ° C or above 38 ° C.
•• Failure to do so may damage the product.
Power requirements
This product should only be used with AC 230~240V. Make sure to check the power specifications of the
place where you intend to use the product.
•• The wrong specifications will result in electric shock or damage the product in the event of a short-circuit.
Do not apply excessive force to the power cord to bend it, or place it under a heavy object as this will
damage it.
•• The power cord may get damaged and cause electric shock or injury.
Please refrain from using multiple power appliances in one power board or power socket and make sure to
use a power socket with a capacity of 10A.
•• Failure to do so may result in fire due to abnormal overheating of the socket.
•• Or it may activate the circuit breaker leading to a loss of power.
Never touch the power cord and plug with a wet hand.
•• This may result in injury or electric shock.
Please clear any dust or water from the power cord and plug with a dry cloth.
•• Failure to do so may result in electric shock, short circuit or fire.
When unplugging the power cord, never pull the cord itself and always hold the power plug.
•• Failure to do so will damage the cord it and may result in electric shock or fire.
06
Stop using the product and contact the customer service department of LG Electronics if the power cord or
power plug is damaged or the holes of the power outlet socket are loose.
•• Failure to do so may result in electric shock or fire.
Make sure to unplug the power cord when cleaning or maintaining the charging station.
•• Failure to do so may result in injury or electric shock.
Make sure to unplug the power cord when the product is not to be used for an extended period of time.
•• Failure to do so may result in electric shock, short circuit or fire.
Make sure to organize the power cord of the Adaptor while using or cleaning the product.
•• Otherwise, the cord may get tangled with the product and result in malfunction, electric shock or injury if its
disconnected or broken.
Avoid touching the pins of the power plug with your finger(s) when unplugging the power cord.
•• Failure to do so may result in electric shock or fire.
Do not to let children or pets get close to the product when using, charging or storing.
•• It may damage the product and/or result in injury.
Do not hold the charging station upside down with the battery in the charging station.
•• Otherwise, it may damage the product and/or result in injury.
Proper usage
Make sure that no child is allowed to use the product.
•• The product is too heavy for a child to handle properly.
Make sure that no hand, foot, hair or clothes gets stuck in the rotating brush or wheel while using or
cleaning the product.
•• Failure to do so may damage the product or result in injury.
No one other than a qualified technician/service engineer from LG Electronics may disassemble, repair or
modify the product.
•• Do not attempt to disassemble or repair the product yourself as it may result in electric shock, injury or fire.
Do not arbitrarily disassemble, remove or short-circuit the battery.
•• It may result in electric shock, injury or fire.
Do not apply heat or shock to the battery.
•• It may cause electric shock, injury or fire.
Never insert a sharp metallic object such as a pin, nail or knife in a hole or gap in the product or the charging
station.
•• Otherwise, you may get injured or suffer electric shock.
Do not vacuum liquids with this product. Make sure that no water, beverage or detergent gets inside the
product or the charging station.
•• Failure to do so may result in injury or electric shock.
Do not apply or spray a flammable substance (gasoline or thinner) or surface active agent (detergent or
bath soap) on the product.
•• It may result in malfunction or fire.
In the event of a gas leakage (propane or urban gas), make sure to ventilate the area first without coming
into contact with the product or its power plug.
•• Otherwise, there may be sparks which may result in an explosion, fire or injury.
07
Do not let liquid stain the upper part of the mop nozzle. Do not clean a wet floor.
•• It may damage the product or cause electric shock.
Do not use or store a heating device or flammable substance(ether, benzene, alcohol, chemicals,
combustible spray, insecticide, air freshener or cosmetics) in close proximity to the product.
•• It may result in product malfunction or fire.
Do not attempt to clean up a liquid substance (water, beverage), odorous substances (candy, chocolate, pet
excrement, etc.), metallic objects (such as blade, pins), flammable substances, surface active agents, or
glass shards with this product.
•• It may result in product malfunction or fire.
•• In the event that any liquid, metallic object, glass shard or spark gets inside the product, immediately turn off the
product and contact the customer service department of LG Electronics.
Do not use the product with the exhaust or inlet port blocked.
•• It will cause the product to overheat and result in malfunction or fire.
In the event that smoke is emitted by the product while it is charging, immediately unplug the power cord
and contact the customer service department of LG Electronics.
•• Failure to do so may cause electric shock or fire.
Do not expose the product, and the battery in particular, to heat, a heating device or direct sunlight.
•• It may result in electric shock, explosion or fire.
Do not keep the product or its battery inside a vehicle which is exposed to direct sunlight.
•• It may cause fire or explosion.
Do not wash the inlet port with water or detergent.
•• As the inlet port contains a motor, it may result in electric shock or fire.
Always use the charging station and adaptor provided with the product to charge the product and its battery.
•• Using any charging device other than the provided station and adaptor will damage the battery and result in electric
shock, explosion or fire.
Never allow any water, beverage or detergent to get inside the battery.
•• It may cause electric shock, explosion or fire.
Do not touch the charging terminals on the product or the charging station, or insert an electrified object
inside the product or the station.
•• Otherwise, you may get injured or suffer electric shock.
Always leave the product on the floor standing or wall-mount charging station when it is not in use. Do not
leave the product on the charging station not fixed to the wall or charging station support.
•• Otherwise, the product may fall and get damaged or cause injury.
In the event that the earth leakage breaker gets activated while the product is placed on the charging
station, immediately remove the product from the station and contact the customer service department of
LG Electronics.
•• Failure to do so may cause electric shock or fire.
Do not wash the dust bin with water.
•• The water will get into the motor and cause electric shock or fire.
Do not attempt to vacuum fine dust such as cement with the product.
•• It may cause product malfunction or fire.
Make sure that no child can play with the product, charging station or battery.
•• It may damage the product and cause an injury.
08
•• If a child places the product or battery into its mouth, it will cause electric shock or injury, or damage the product or
battery.
When using the product, remove any wire or string from the bottom of the Charging Station.
•• Straps or wires may wrap around the product and cause a product malfunction or a broken cord.
Do not insert your finger into the moving rotor.
•• It may cause an injury or product damage.
Take caution not to get fingers caught in the flexible part of the nozzle.
•• Failure to do so may result in injury.
Do not vacuum sharp objects (glass pieces, wire, blades, pins, etc.) with the mop nozzle attached.
•• It may cause injury or product damage.
•• Particularly, a sharp object embedded in the mop, can cause injury when cleaning the mop pads after mopping.
Mopped floors may become slippery until completely dry after using the mop function.
Please use caution if walking over mopped floors as they may be a slip hazard.
•• Failure to do so may result in injury.
Disposal
Discard the packing materials (plastic vinyl, styrofoam) properly so that no child comes into contact with
them.
•• Such materials may cause a child to suffocate.
09
CAUTION
Proper usage
Do not apply impact to the product or drop it from a height.
•• It may damage the product and/or result in injury.
Make sure that the product does not fall.
•• It may cause injury or damage the product.
Make sure that the filter is installed in the product prior to each use. Do not install wet or damp filters.
They must be dry before fitting them.
•• Failure to install a filter may result in product malfunction.
Make sure to wipe up any liquid such as water or oil or pet excrement from the floor before using the
product.
•• Such substances will cause the unit to malfunction or cause irreparable damage
Do not clean the product with a volatile or organic solvent (thinner or acetone).
•• It may damage the product.
•• Always use a soft cloth to clean the product.
Make sure to avoid running into a person or a pet while using the product.
•• It may cause injury.
Do not kick or apply impact to the product.
•• It may cause the product to malfunction.
Do not put any object other than the product, especially a metallic or magnetic object, on the charging
station.
•• It may damage the product or cause electric shock.
Do not clean the same spot repeatedly for an extended period of time.
•• Vibration from the inlet port or rotating brush may damage the floor or the carpet.
Make sure that your finger does not get stuck when assembling the product or the charging station.
•• It may injure your finger.
Do not let a child or a pet hang onto the charging station.
•• It may cause injury or damage the product.
Do not put double-sided tape directly onto the wallpaper as it may be torn by external force.
•• Anchor the charging station with the wall anchoring screw(s) to prevent tearing of the wallpaper.
Do not apply force or impact to the filter parts or dust bin parts.
•• The parts may become deformed, compromise the performance or cause the unit to malfunction.
Do not remove the battery during operation.
•• It may cause the product to malfunction.
If the motor is overheated by using the product for a long period of time, the product will automatically turn
off by its built in safety device to prevent heat damage
•• After cooling for about 1 hour in a cool, well-ventilated area, turn on the power again.
10
Do not leave the product standing on the charging station while the mop nozzle (and its water tank)
attached to the main body.
•• The water may leak and damage the floor.
Do not store the water tank where the temperature is 0 ºC or lower.
•• It may result in product damage.
Do not clean the same spot repeatedly for an extended period of time.
•• The water injection at the mop nozzle may cause the water get into the dust inlet and damage the main body.
Do not use the mop nozzle for any purpose (e.g.: polishing a car, cleaning windows) other than domestic
floor cleaning application
•• It may result in product damage.
Do not trample on the mop nozzle.
•• It may result in product damage.
Do not use the mop nozzle to vacuum liquid.
•• It may result in product damage.
When using the mop nozzle, always attach the mop pads.
•• Failure to do so may cause damage to the floor or carpet.
Do not clean the carpet with the mop nozzle.
•• The carpet may get wet or stick to the Velcro, causing damage to the carpet.
Do not clean a coated floor.
•• If used repeatedly, the coating may peel off.
Do not use the mopping functions on delicate floating floors.
•• Floors may absorb the moisture and become deformed.
11
Package information
Standing type
4
1
10
6
7
2
5
9
3
8
Wall-mount type
1
10
4
6
2
9
3
1
Product body
5
Charging station pipe
9
2
Extension pipe
6
10 Battery
3
Multi-surface Power Drive
Nozzle®
Combination tool and crevice
tool holder
7
4
Charging station
Detachable stand for nozzle and
mop pads
8
Charging station support
12
Adaptor
Accessories
• Parts and accessories may vary depending on the model that you have purchased.
Product body
Extension pipe
Multi-surface Power
Drive Nozzle®
Charging station
Adaptor
Crevice Tool
Combination Tool
Wall Anchoring Block
Double-sided tape (2)
1)
Battery
1)
Screw Anchor (2)
Anchoring screw for
wall-mount type (Φ
3.5 mm, length 50
mm)(2)
Anchoring screw for
standing type (Φ 3.5
mm, length 90 mm)
Pre-filter
(Spare)
Charging station pipe
Multi Angle Tool
Flexible Hose
Extension
Charging station
support
• Please note that these parts come with their corresponding models only.
Hard Dirt Tool
Mattress Tool
Flexible CreviceTool
2)
1)
Battery
2)
Detachable stand for
nozzle
Hard Floor Power
Drive Nozzle®
Bedding Power Punch
Mop Nozzle
Detachable stand for
mop pads
1)
Mop pads (4)
Water filler jug
1) Mop pads, batteries and the pre-filter are consumables. You can buy them from an Authorised LG service or parts provider.
2) For some models, the Detachable stand for mop pads, mop nozzle and other nozzles are provided together in an
assembled condition.
13
Installation
Installing the floor standing
charging station
1
4
Place the charging station support on the floor and
assemble the charging station pipe, the Detachable
stand for nozzle and mop pads and the charging
station in this order.
Put the anchoring block on the back of the charging
station and anchor the charging station with the
screw.
• Make sure to fully tighten the screw.
Wall anchoring block
Anchoring screw
for standing type
Screw
anchor
Charging
station
Charging
station
pipe
Detachable
stand for
mop pads
Click
Detachable
stand for nozzle
Charging station
support
CAUTION
2
• Avoid getting your fingers stuck in any gap.
Connect the power adapter to the port on the back
of the charging station and plug the power cord
into the power outlet.
• The cord can be secured tidily by putting it
through the power cord anchoring ring located
on the back of the charging station pipe.
When using double-sided tape (do not use
if the wall is wallpapered)
1
Use double-sided tape to attach the wall anchoring
block to the charging station in step 4.
• Be sure to remove the center part of the doublesided tape before mounting it.
Wall anchoring block
②
①
3
After ensuring there are no pipes or wires inside
or behind the wall, make a hole at the appropriate
height to anchor the charging station and insert
the screw anchor.
• Recommended diameter of hole: Φ6.5;
Recommended depth: 100 mm.
Screw anchor
14
2
Use the remaining part of the tape to anchor the
station to the wall before inserting the screw.
CAUTION
Installing the wall-mount station
• Avoid dropping the product and parts when taking them
1
•
2
•
•
•
•
out of the package. It may damage the product and/or
cause personal injury.
Do not use double-sided tape to anchor the charging
station on papered walls. Please use the provided screws
as otherwise the wall paper will get torn by movement
of the charging station during the docking of the unit.
We recommend anchoring the station with the
anchoring screw.
Use the anchoring screws only when the wall is made
of concrete or is solid enough. An unsuitable wall
can cause the mountings to weaken and cause the
Charging station to fall causing injury and damage the
property or product.
Do not store the product or battery in the accessory
bag except for the inlet ports and flexible hose
extension.
Be careful not to throw or drop the accessory bag
carrying accessories such as the inlet ports. It may
damage the product and/or cause personal injury.
* The accessory bag is provided only for an applicable
model.
Please note
• The charging station, its pipe and support cannot
be disassembled separately once they have been
assembled, and the charging station has been
attached to the wall.
• If necessary, the charging station and the nozzle
cradle can be separated from the charging station
pipe. Pull the charging station upward and separate it
in sequence while the charging station support is in a
fixed state.
3
Connect the power adapter to the port on the back
of the charging station and plug the power cord
into the power outlet.
Ensure that there are no Electrical wires or water
pipes inside the wall where the wall mount bracket
will be attached to. By drilling or screwing, make a
hole 1 meter from the floor to insert the wall plug
or screw anchor.
• Recommended diameter of hole: Φ6.5;
Recommended depth: 60 mm.
Anchor the station to the wall with the provided
anchoring screws.
Wall anchoring
hole
Anchoring
screw for wallmount type
Screw
anchor
1
Please note
• A service request to change the installation location
of the charging station will incur additional costs if
required to do so by a qualified installer.
• The Detachable stand for the nozzles and the
Detachable stand for mop pads cannot be separated
once they are assembled.
Uninstalling the station
Keep and charge the product on the charging station
after separating extension pipe and nozzle from the
product body.
CAUTION
• Leaving the extension pipe and nozzle assembled for a
long time may cause damage the product.
15
Storage of the combination tool
and crevice tool
Keep the combination tool and crevice tool on the
charging station for easy access.
1
2
Attach the combination tool and crevice tool to the
dedicated holders.
Storage of the Mop Nozzle
Storing mop nozzles on the Detachable stand for nozzle
and mop pads helps in finding and using the mop nozzle.
1
Mount the mop nozzle to the nozzle cradle.
2
Lift the nozzle to separate the mop nozzle.
Press and hold the inlet removal button and pull
downward to remove the combination tool or
crevice tool.
* The Multi-surface Power Drive Nozzle® can be stored
as well.
Storage of the Mop Pads
Storing mops on the Detachable stand for mop pads
helps in finding and using the mop. Up to 2 mop pads can
be stored.
• After cleaning with a mop pad, wash and dry the mop
•
•
•
•
16
pads before storage. A mop pad which has not been
properly dried may emit an odour when stored.
We recommend to hand-wash the mop pad with a pHneutral detergent.
Do not use bleach or fabric softener when washing
the mop pad.
It is not recommended to use a laundry dryer to dry
the mop pad.
Do not boil the mop pad. The mop pad may become
deformed.
How to Use
Note about using the product
Using the Product
Points to be aware of when using the
product
1
Assemble the body, extension pipe, inlet port, and
battery in that order.
• Make sure that the dustbin lid is on prior to using
•
•
•
•
•
•
•
•
•
•
•
the product. Otherwise, the suction strength will
deteriorate and cleaning will not be satisfactory.
Support the bottom of the product when cleaning an
elevated surface.
When leaving the product unattended or unused for
an extended period, make sure to place it properly on
the charging station or lie it on the floor. Otherwise,
the product may fall and get damaged or cause an
injury.
Make sure that the exhaust filter is properly
assembled before using the product.
Environmental conditions such as temperature
and humidity may cause static to accumulate on
the product. Please contact the customer service
department of LG Electronics if the problem persists.
Any foreign object on the inlet port or extension pipe
will prevent the product from functioning properly.
Make sure to remove any foreign object such as a sock
or stocking before using the product.
The battery runtime will be shortened after using the
product repeatedly for an extended period due to its
characteristics.
When the battery is about to become fully run down
during use, the last block on the battery indicator will
start to flash and the product will power off after a
while. Fully charge the battery in this case.
Please use the product at normal room temperatures
as the battery runtime will deteriorate severely if used
at temperatures lower than 5℃ or higher than 38℃
for an extended period of time.
Refer to Product specifications for battery run time
details.
These times are a guide only and may be less
depending on the surface type.
It is recommended to swap the battery on the main
body and the battery on the auxiliary charging station
regularly for maintaining the maximum life of the
batteries. (For dual-battery models only)
Product
body
Inlet port
Battery
Extension pipe
2
Press the button on the extension pipe to adjust its
length.
• The pipe has 4 extendable length positions
Pipe length
extension button
3
Attach the accessory tool to the body or the
extension pipe.
Extension pipe
CAUTION
• Prolonged use of the product with the accessory tool
attached may overheat the motor.
• Using the inlet port to clean a TV, monitor or LCD
display may scratch the screen.
• Exercise caution to avoid getting your finger stuck in
any gap when assembling the attachments.
• If any foreign object is sucked into the inlet during
cleaning, operation of the vacuum cleaner might stop
in order to prevent damage to the body or motor.
Immediately stop using the vacuum cleaner and
remove the object before resuming cleaning.
17
Charging the Product
1
Put the product on the charging station.
• The battery indicator will start to flash and
charging will proceed in 3 steps.
2
Insert the battery into the auxiliary charging
station.
Charging indicator
of the auxiliary
battery
2
The battery indicator starts to flash and charging
will start.
• All of the indicators will stay on when the battery
is fully charged.
CAUTION
• Make sure to securely fit the unit on to the charging
station. Otherwise, the product may fall and get
damaged.
Please note
• Make sure that the power adapter is connected to
both the charging station and the power outlet
• If the main battery is charging on the charging station,
the auxiliary battery will only start charging once the
main battery is fully charged.
• The auxiliary battery indicator flashes when charging
starts.
• The indicator will stay on when the auxiliary battery is
fully charged.
• Fully charging a single battery usually takes 3.5 hours,
but it will take twice as long if you charge it along with
a discharged auxiliary battery.
Power / Suction Strength button
You can adjust the suction strength with the suction
strength button located on the handle.
1
Please note
• The battery will not be charged if the ambient
temperature is below 5°C. only charge the battery
when ambient temperatures are between 5° and 38° C.
• The battery indicator will flash if the product is fully
charged, removed from the station, and charged again
soon. The flashing stops soon, and the indicator stays
on.
Charging the auxiliary battery
1
18
Hold the product and pull the battery by pressing
both ends of the battery.
2
1
Power On/Off button
• Press the power On/Off button to activate the
Normal mode.
2 Mode button
• Press "+" once to activate the Power mode.
• Press and hold "+" for more than 3 seconds to
activate the Turbo mode.
• The unit will take a moment to switch to the
Turbo mode from the Normal mode when the "+"
button is held down.
• Press "-" to switch from Turbo to Power, or from
Power to Normal.
Using the nozzles
• Please note that the following applies to the
corresponding models:
• The nozzle can be attached to the product body or
extension pipe.
• Use a different mode if the inlet gets stuck on the
floor, carpet or bed sheets or if you need a more
powerful mode.
CAUTION
• Do not use the product for any purpose other than
domestic household.
Crevice Tool
It is suitable for cleaning dust in a corner or a narrow
space.
Combination Tool
This accessory is helpful for cleaning corners or small
gaps.
Basic
For cleaning flat surfaces such as a sofa or mattress.
Multi-surface Power Drive Nozzle®
• It is suitable for cleaning carpets or rugs.
• It can be used to clean hard floors but will generate
some noise.
CAUTION
• Do not use this nozzle on a play mat (PVC) for children.
Hard Floor Power Drive Nozzle® (some
models only)
• It is suitable for cleaning hard floor surfaces.
Brush type
For cleaning delicate surfaces such as a frame or
furniture.
Button
Bedding Power Punch (some models only)
• Bedding Power Punch lets you clean bed sheets and
covers more effectively. This attachment can be used
to remove Pet Hair from various surfaces without hair
tangling.
• Make sure to adjust the suction level to an appropriate
setting when you vacuum-clean a blanket with a thin
outer fabric as the cleaner may attempt to suck the
outer fabric.
CAUTION
•
•
•
•
Prolonged use of the product with an accessory tool
attached may over heat the motor.
Using this accessory tool on a TV, monitor or LCD
display may scratch the screen.
Avoid getting your finger stuck in any gaps when
fitting the accessory tools.
If any foreign object is sucked into the inlet during
cleaning, operation of the unit might stop in order
to prevent damage to the body, motor or inlet.
Immediately stop using the vacuum cleaner and
remove the object before resuming cleaning.
19
Hard Dirt Tool
Multi Angle Tool
It is firm bristles for removing dirt from hard surfaces.
Since it can be adjusted to various angles and the brush
is soft, it is used to clean the console in the vehicle or on
top of furniture.
Mattress Tool
Flexible Hose Extension
It is for mattresses and soft furnishing.
Flexible Crevice Tool
Since its length can be adjusted and it can be bent, it
is used for cleaning dust inside the vehicle or narrow
spaces in furniture where bending is necessary.
1
How to operate the brush
• You can use the brush by holding and pulling the
brush fixing unit in the arrow direction.
• You can insert the brush by pressing the button
and inserting the brush fixing unit in the opposite
direction of the arrow.
Button
Brush fixing
unit
2
How to adjust the length
• Adjust its length by pressing the length extension
button and pulling or pushing it to the end.
Length extension button
20
Since its length can be adjusted, it is connected with the
inlet port and used to clean out of reach places.
* The flexible hose extension is provided only for an
applicable model.
Please note
• When the flexible hose extension is used, the Multi-
surface Power Drive Nozzle®, Hard Floor Power Drive
Nozzle® and the Bedding Power Punch do not work.
• Attach the Multi-surface Power Drive Nozzle®, Hard
Floor Power Drive Nozzle® or the Bedding Power
Punch to the body or the extension pipe when using it.
Mop Nozzle
How to install the mop
It is suitable for cleaning dust and mop cleaning at the
same time.
1
Wet the mop pad with water before use.
Please note
The mop pads will only rotate at one speed regardless of
what power setting the Vacuum is set to.
For mop cleaning
How to fill the water
1
Press the PUSH button to separate the mop nozzle
and the water tank.
2
Squeeze the mop pad sufficiently to remove liquid.
2
Open the cap on the side of the water tank.
• Open one cap only. Opening both caps may cause
the water to flush.
3
Align the center of the mop pad with the center of
the mop attachment plate, and have the striped
side of the mop face up.
3
Fill the water to the MAX line and close the cap tightly.
(Using the water filler jug will make the filling of water
easier.)
• Fitting the mop plate upside down or failure to attach
the mop pad to the attachment plate properly may
compromise the cleaning performance.
• Attaching the mop pad in a dry state may compromise
the cleaning performance.
※ How to install the mop pad properly
Good)
Bad)
• If the water tank is filled with water and stored, water
may slowly drip from the water tank and on to the air
intake. When not using the mop nozzle, ensure that
the water tank is empty empty.
• If you do not close the cap on the side of the water
tank, water may leak.
Good)
4
Bad)
How to adjust the water flow to the Mop Pads
The amount of water injected from the mop nozzle
can be adjusted.
Assemble the mop nozzle and the water tank.
Insert the 2 bumps in front of the tank and push
until a clicking sound is heard.
Click
Used to clean a moisture-sensitive
floor or to supply a little amount of
water
Used to clean ingrained dirt or to
supply a large amount of water
Used to stop the supply of water or
clean with a dry mop
21
For dry mop cleaning
1
2
3
Empty the water in the water tank.
Please note
• When using a mop, clean using straight lines and
diagonal lines.
Attach the dry mop pad to the mop attachment
plate at the bottom of the mop nozzle.
Set the Water Adjustment button to STOP.
• Wet the mop and squeeze it sufficiently to remove
4
Turn on the power and begin mopping
•
WARNING
• Do not insert your hand into the moving rotor. It may
result in injury.
• Do not attach the mop pad while the mop nozzle is
operating. It may result in injury.
•
•
•
CAUTION
• Do not slam down or throw the mop nozzle onto the
•
•
•
•
•
•
•
•
floor.
Doing so may result in an injury or product damage.
Do not let the product stand on the floor while the
wet mop plates are attached.
Doing so may result in damage or swelling to timber
flooring.
Set the Water Adjustment button to STOP when not
using the product for an extended period of time.
Otherwise it may result in a product failure.
Do not use any other mop pad other than the one
provided.
Do not put liquid other than water in the water tank.
Do not put hot water in the water tank.
Do not step on the mop nozzle. It may result in
product damage
• After cleaning, remove the remaining water in the mop
nozzle with a tissue before storing. The water may
leak and damage the floor.
• Do not pull on the marked rubber. It may tear.
22
•
•
•
•
any residual water before attaching the mop.
Attaching and using a mop pad in a dry state may
compromise the cleaning performance.
When filling the water tank with water, do not fill the
water more than the MAX line.
Do not separate the cap of the water tank completely.
Open only one cap of the water tank to fill the water.
When cleaning is completed, always empty the water
in the water tank.
Otherwise the water may be contaminated and give
off a bad smell.
Shake the water tank to remove the remaining water.
Open the 2 caps on the side of the water tank and dry
for over 24 hours in a well-ventilated location with no
direct sunlight.
When cleaning with the mop is finished, separate and
wash the mop pads.
Otherwise the mop pads may give off a bad smell.
Do not clean while a soiled mop pad is installed.
Cleaning will not be effective.
From new, the Water Adjustment button is set to
Level 1.
Press the button according to the amount of water
needed.
When moving around with the mop nozzle, set the
Water Adjustment button to STOP.
If there are foreign objects stuck in the mop
attachment plate's rotating mechanism or a strong
force or impact is applied to it, the mop attachment
plate will stop automatically to protect the product.
Press the Power button again to use the product
because it is not a failure. Clean any foreign matter
from the plate before turning it back on again.
Maintenance
Cleaning the the Dustbin
1
Remove the battery from the unit before cleaning
the dustbin.
2
Please empty the dustbin next to a wastebasket
or where dust and foreign objects can be emptied
easily.
3
Press the dustbin button downward to open it.
• Empty the bin.
• Be careful as dust/foreign matter may spill out
when you open the dustbin.
6
Remove the Cyclone and use the combination tool
to clean out the dust inside the dustbin.
Combination
Tool
WARNING
• Never wash the product's body with water. Water may
reach the motor and cause electric shock or fire.
• Do not apply force or any impact to the dust bin parts
or the Cyclone as it may damage them.
• Use the product only after cleaning the Cyclone and
reassembling it on the product. Failure to do so will
damage the product.
Dustbin Button
4
Insert the crevice tool into the large dust
separation device (Cyclonic Mesh Filter) and turn it
counterclockwise to remove it. Use the suction end
of the crevice tool to do this with ease.
Cleaning the Filters
The pre-filter and exhaust filter need to be cleaned
regularly to maintain the cleaning performance of the
product. Clean these filters more frequently when used
in dusty environments. Both the Pre-filter and the
Exhaust filter should be washed in running water at
least once a month and allowed to dry thoroughly before
refitting them.
1
Turn the exhaust filter counterclockwise to remove
it and take out the pre-filter.
Exhaust filter
5
Wash the large dust separation device (Cyclonic
Mesh Filter) with running water.
• Be sure to dry the device completely before
reinserting it.
2
Pre-Filter
(Yellow/
Green cloth
type)
With the unit upside down, use the combination
tool to clear dust from the motor part once the
Dust separator filter has been removed.
Large dust
separation
device
(Cyclonic
Mesh
Filter)
Combination
Tool
23
3
Clean the exhaust filter by brushing the dust off it
regularly and wash it at least once a month.
WARNING
• Never wash the product's body with water as it may
reach the motor and result in electric shock or fire.
• Make sure that no foreign object reaches the motor as
• Wash the exhaust filter in running water if it
emits an odor.
• The exhaust filter may emit an odor if it is not
dried completely after it has been cleaned in
water. Make sure to dry both the Pre-filter and
the Exhaust filter for 24 ~ 48 hours in a wellventilated area out of the direct sunlight before
refitting them.
it will damage the product and may result in explosion
or fire.
• Do not insert a finger or a sharp object near the motor
as it will damage the product and may result in injury
or electric shock.
CAUTION
• Make sure to reattach the exhaust filter and pre-filter
to the product after washing them. Using the product
without these filters will allow dust to reach the motor
inside the product and cause malfunction.
Please note
• As too much dust will reduce the suction power, we
recommend cleaning the filters before and after using
the product.
※ Removing foreign objects from inside the
product
4
Clean the pre-filter by brushing the dust off it regularly
and wash it at least once a month in running water.
• After washing the cloth type pre-filter with water,
it must be dried completely in a well-ventilated
area out of direct sunlight before reinserting.
Failing to do so will cause it to emit odours and
may cause the motor to malfunction.
• As a spare pre-filter is provided for your
convenience, two pre-filters can be used
alternatively if necessary.
• The more often the filters are cleaned, the more
optimal the suction power will be.
• Filters are consumables and will wear with time
and use. Please purchase more filters from an
authorized service center.
In order to maintain product performance, be sure to
remove any foreign objects and dust from inside the
product (body, pre-filter, extension pipe, inlet port).
The foreign materials inside the product can cause the
product to shutdown during operation, generate noise,
or cause poor suction.
Foreign objects
Pre-filter
Foreign
objects
Product body
Product body
Pre-filter
Foreign
objects
Foreign
objects
5
24
Extension pipe
To refit the filters, attach the pre-filter first, followed
by the exhaust filter, so as to align the white circle near
the battery level indicator and then turn it clockwise
so that the white circles align with each other.
Foreign
objects
Inlet port
※ If the inside of the product body, extension pipe, or
inlet port or the pre-filter itself is clogged with foreign
objects, the power automatically turns off to protect
the product. Separate the battery from the product
and remove the foreign objects.
Cleaning the Hard Floor Power
Drive Nozzle®/Multi-surface Power
Drive Nozzle®
Please clean the Hard Floor Power Drive Nozzle® and
Multi-surface Power Drive Nozzle® as follows:
1
2
Remove the nozzle from the product.
Turn the nozzle upside down and turn the rotating
brush removal screw counterclockwise.
• Use a flat head screwdriver to turn the screw.
Rotating the brush
removal screw
3
CAUTION
• Avoid getting your finger stuck in any gaps when
reassembling.
• Do not wash the rotating brush and the nozzle with
water.
• Do not use the rotating brush as a mop.
• Do not use the nozzle to absorb any liquid.
Cleaning the Bedding Power Punch
1
Remove the Bedding Power Punch and turn it
upside down.
2
Attach the crevice tool to the unit and use the
vacuum to remove dust/foreign objects from the
bottom of the Bedding Power Punch.
3
Use a wet towel or tissue to move any remaining
foreign matter and dust.
Pull the brush in the direction of the arrow to
remove it.
①
②
4
Attach the crevice tool to the unit and use the
vacuum to remove dust/foreign objects from the
brush and the bottom of the nozzle.
Rotating
brush
5
Use a wet towel or tissue to remove any remaining
foreign matter and dust from the brush and the
bottom of the nozzle.
Rotating
brush
WARNING
• Do not wash the Bedding Power Punch with water.
• Do not suck any liquids including water into the
Bedding Power Punch.
6
Assemble the brush in reverse order after cleaning.
②
①
25
Cleaning of the Mop Nozzle
Drying the water tank
Clean the mop nozzle as below.
Open the 2 caps on the side of the water tank and shake
the water tank to remove the remaining water.
Drying thoroughly for over 24 hours in a well-ventilated
location with no direct sunlight is effective to remove
moisture from the water tank.
1
Separate the nozzle from the product and turn the
nozzle over.
2
Attach the crevice tool to the main body of the
vacuum to remove any foreign objects from its
base.
Please note
• When cleaning is completed, always empty the water
3
Remove the remaining foreign objects using a wet
wipe or a tissue.
in the water tank.
Otherwise the water may be contaminated and give
off a bad smell.
CAUTION
• Turn the direction of the cap to prevent the cap of the
water tank from being closed.
• Do not separate the cap of the water tank completely.
• Do not add detergent, vinegar or baking soda to the
water tank when washing.
※ Foreign matter remaining on the nozzle may result in
a bad smell.
WARNING
• Make sure to separate the nozzle from the main body
or separate the battery before cleaning.
Otherwise the mop attachment plate may rotate and
result in injury.
CAUTION
• Do not clean or submerge the nozzle with water. It
may result in product damage.
26
Points to check before contacting customer service.
Please check once again if one of the following symptoms is present while using the product. The product may not be
malfunctioning.
Symptom
The product does not
operate.
Suction is too weak.
The unit does not
appear to be charging.
Hot air is expelled
from the unit.
Cause
Is the battery fully discharged?
Is the product powered off?
• Charge the battery.
• Press the power button to power on the
product.
Is the dustbin full of dust?
• Empty the dustbin.
Is the filter clogged?
• Clean the pre-filter and the exhaust filter.
Is the inlet clogged?
• Remove the extension pipe, remove any
foreign objects from the product body.
Is there a foreign object on the
rotating brush of the inlet port?
• Make sure to remove any foreign objects
Is the power adapter connected
to the charging station?
• Make sure that the adapter is properly plugged
Is the power cord plugged into
the outlet?
• Make sure that the power cord is properly
Is there any foreign object on the
charging terminals?
• Remove any foreign objects from the charging
Is it operating properly?
Did you purchase the cleaner
within the last 3 months?
Is it operating properly?
Is the dustbin full of dust?
Are there any foreign objects in
the filter?
A strange odor is
coming from the
product.
Solution
(thread, hair) from the rotating brush.
into the charging station.
plugged into the power outlet.
terminals with a dry cloth.
• The hot air originates from cooling of the
motor and is not a sign of malfunction.
• The cleaner may emit a smell of rubber for
about 3 months after purchase.
• If the cleaner is working fine, it is not
malfunctioning.
• Also, dust in the bin may cause some odor.
Empty the bin and clean it.
• The filter may emit an odor if it has not been
cleaned for some time. Clean both the prefilter and the exhaust filter.
• Washing the pre-filter with water and not
Is the pre-filter wet?
leaving it long enough to dry completely
may cause it to smell. Make sure to dry it
completely before reassembling it on the
cleaner.
• Washing the exhaust filter with water and
Is the exhaust filter wet?
Are there any foreign objects on
the dust inlet of the mop nozzle?
not leaving it long enough to dry completely
may cause it to smell. Make sure to dry it
completely before reassembling it on the
cleaner.
• Wet dust in the mop nozzle may result in
odour. Make sure to wipe the dust inlet of the
mop nozzle with a wet wipe before use.
27
Symptom
The cleaner makes too
much noise.
Cause
Is it operating properly?
Solution
• Different levels of noise is normal during
operation due to three power settings. It is not
a sign of malfunction.
• The battery must be fully charged before
Is the battery fully charged?
The unit powers off
too soon or by itself
after the motor speed
fluctuates repeatedly.
Is there any foreign substance
in the body of the product,
extension pipe, or inlet port?
Is the filter clogged?
The rotating brush
does not rotate.
The mop pad
attachment plate does
not rotate.
Is the brush properly attached?
Are there any foreign objects on
the rotating brush?
Did you press the mop nozzle
hard?
Are there any foreign objects
between the mop attachment
plate?
Is the water tank filled?
There is no water
coming out of the mop
nozzle.
Is the water tank properly
attached to the mop nozzle?
Is the Water Supply Adjustment
button on?
There is moisture in
the water tank.
Have you thoroughly dried the
water tank?
Using the mop nozzle
makes the floor dirtier.
Did you clean the mop before
use?
28
cleaning. If the problem persists even though
the battery is fully charged, and the pipes and
attachments are clear from obstructions, then
please contact LG customer service
• Remove the foreign objects from the body of
the product, extension pipe, or inlet port.
• Clean the pre-filter and the exhaust filter.
• Remove the brush, clean it if necessary and
attach it again.
• Remove any foreign objects from the rotating
brush.
• The mop attachment plate stops automatically
to protect the product. This is not a failure.
Press the power button again to use the
product.
• Remove foreign objects from the mop nozzle
attachment plate and press the power button
again to use the product.
• In order for the water to come out of the mop
nozzle, the water tank should be filled.
• In order for the water to come out of the mop
nozzle, the water tank should be properly
attached to the mop nozzle.
• The water will not come out if the button is
set to STOP.
• Press the Water Supply Adjustment button
according to the type of cleaning.
• The water tank will become moist if the water
tank is containing water.
• Dry the water tank properly in a shadow.
• Cleaning with a soiled mop may make the floor
dirtier.
• Clean the mop before use.
Disposal information
Disposal of old products not related with the purchase of a new product
You must contact your local city council or the related government authority before disposing of large appliances.
Product specifications
Item/Model
A9**********
Dimensions
260 mm(W) X 270 mm(L) X 1120
mm(H)
Weight
2.7 kg
Power
consumption:
400 W (Maximum power: 450 W)/
250 W/ 80 W (Turbo/Power/
Normal)
Battery
DC 25.55 V
Battery runtime Up to 6 minutes in Turbo
(When fully
charged, and
Up to 9 minutes in Power
without using
the Power Drive
Up to 40 minutes in Normal
nozzles)
Battery runtime Up to 6 minutes in Turbo
(When fully
Up to 9 minutes in Power
charged, and
using the Power
Drive nozzles)
Up to 30 minutes in Normal
Item
Charger (Adaptor)
Input
100 V - 240 V~ 50/60 Hz, 0.8 A
Output
DC 29.4 V 1.0 A
Item/Model
Battery
Type
Rechargeable Li-ion Battery
Rated
DC 25.55 V , 2000 mAh
29
Note
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising