LG | OL45D | Owner's Manual | LG OL45D Owner’s Manual

LG OL45D Owner’s Manual
OWNER’S MANUAL
DVD Mini
Hi-Fi Audio
Please read this manual carefully before operating your set and retain it for future
reference.
MODEL
OL45D
MFL71401802
1902_Rev01
www.lg.com
Copyright © 2019 LG Electronics Inc. All Rights Reserved.
2
Getting Started
Safety Information
1
CAUTION
Getting Started
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF ELECTRIC
SHOCK DO NOT REMOVE COVER (OR BACK)
NO USER-SERVICEABLE PARTS INSIDE REFER
SERVICING TO QUALIFIED SERVICE PERSONNEL.
This lightning flash with arrowhead
symbol within an equilateral
triangle is intended to alert the
user to the presence of uninsulated
dangerous voltage within the
product’s enclosure that may be of
sufficient magnitude to constitute
a risk of electric shock to persons.
The exclamation point within an
equilateral triangle is intended
to alert the user to the presence
of important operating and
maintenance (servicing)
instructions in the literature
accompanying the product.
WARNING: TO PREVENT FIRE OR ELECTRIC SHOCK
HAZARD, DO NOT EXPOSE THIS PRODUCT TO RAIN
OR MOISTURE.
CAUTION: The apparatus should not be exposed to
water (dripping or splashing) and no objects filled
with liquids, such as vases, should be placed on the
apparatus.
WARNING: Do not install this equipment in a
confined space such as a book case or similar unit.
CAUTION: Do not use high voltage products around
this product. (ex. Electrical swatter) This product may
malfunction due to electrical shock.
CAUTION: This product employs a Laser System.
To ensure proper use of this product, please read
this owner’s manual carefully and retain it for future
reference. Shall the unit require maintenance, contact
an authorized service center.
Use of controls, adjustments or the performance of
procedures other than those specified herein may
result in hazardous radiation exposure. To prevent
direct exposure to laser beam, do not try to open the
enclosure.
CAUTION: Do not block any ventilation openings.
Install in accordance with the manufacturer’s
instructions.
Slots and openings in the cabinet are provided
for ventilation and to ensure reliable operation of
the product and to protect it from over heating.
The openings shall never be blocked by placing
the product on a bed, sofa, rug or other similar
surface. This product should not be placed in a builtin installation such as a bookcase or rack unless
proper ventilation is provided or the manufacturer’s
instruction has been adhered to.
NOTICE: For safety marking information including
product identification and supply ratings, please refer
to the main label on the bottom or the other surface
of the product.
Getting Started
CAUTION concerning the Power Cord
The Power Plug is the disconnecting device. In case
of an emergency, the Power Plug must remain readily
accessible.
Do not overload wall outlets. Overloaded wall outlets,
loose or damaged wall outlets, extension cords, frayed
power cords, or damaged or cracked wire insulation
are dangerous. Any of these conditions could result
in electric shock or fire. Periodically examine the
cord of your device, and if its appearance indicates
damage or deterioration, unplug it, discontinue use of
the device, and have the cord replaced with an exact
replacement part by an authorized service center.
Protect the power cord from physical or mechanical
abuse, such as being twisted, kinked, pinched, closed
in a door, or walked upon. Pay particular attention to
plugs, wall outlets, and the point where the cord exits
the device.
This device is equipped with a portable battery or
accumulator.
How to Safely remove the batteries or the battery
pack from the equipment:
To Remove the old batteries or battery pack, follow
the assembly steps in reverse order. To prevent
contamination of the environment and bring on
possible threat to human and/or animal health, the
old batteries or the battery pack must be put in an
appropriate container at designated collection points.
Do not dispose of batteries or battery pack together
with other waste. It is recommended that you use
local, free reimbursement systems batteries or
battery packs, (may not be available in your area). The
batteries or the battery pack should not be exposed
to excessive heat such as sunshine, fire or the like.
CAUTION: No naked flame sources, such as lighted
candles, should be placed on the apparatus.
Symbols
CAUTION: Be careful to make sure children do not
put their hands or any objects into the *speaker duct.
~
Refers to alternating current (AC).
* speaker duct : A hole for plentiful bass sound on
speaker cabinet (enclosure)
0
Refers to direct current (DC).
Refers to class II equipment.
1
Refers to stand-by.
!
Refers to “ON” (power).
Refers to dangerous voltage.
1
Getting Started
Check the specification page of this owner’s manual
to be certain of the current requirements.
3
4
Table of Contents
Table of Contents
1
Getting Started
3
System Setting
2
6
7
7
7
7
7
8
8
8
9
9
9
10
12
14
Safety Information
Unique Features
Introduction
– Playable Discs
– About the “7” Symbol Display
– Symbols Used in this Manual
– Regional Codes
Playable file Requirement
– Music file requirement
– Photo file requirement
– Video file requirement
– Compatible USB Devices
– USB device requirement
Remote control
Front panel
Rear panel
21
21
21
22
22
23
24
Adjust the setup settings
– OSD Initial language settings - Optional
– To display and exit the Setup menu
– Language
– Display
– Audio
– Lock (Parental Control)
4
Operating
25
26
27
27
2
Connecting
16
16
17
18
18
19
20
20
Connections to Your TV
– HDMI Out Connection
– Resolution Setting
Optional Equipment Connection
– AUX IN Connection
– AUX OUT Connection
– USB Connection
– Antenna Connection
Using the Home Menu
Basic Operations on Disc
Advanced Operations on Disc
– Displaying Disc Information
on-screen
– To display the DVD Menu
– To display the DVD title
– 1.5 times speed playback
– Screen Saver
– Starting play from selected time
– Resume playback
– Changing subtitle code page
– Marked Playback
– Viewing a PHOTO file
Basic Operations on USB
– Selecting a folder and
an MP3/WMA file
– Deleting a file/folder or format
Advanced Operations on USB
– JUKE BOX Playback
Playback Effect
27
27
27
27
28
28
28
29
30
31
32
32
33
33
34
Table of Contents
34
35
35
38
38
38
39
40
40
40
40
41
41
42
43
43
43
43
43
43
43
43
44
46
47
47
47
47
48
49
49
49
50
51
– AUTO DJ
Using BLUETOOTH® wireless technology
– Listening to music stored on the Bluetooth
devices
Using the LG XBOOM App
– About “LG XBOOM” App
– Install “LG XBOOM” App onto Your
Bluetooth Device
– Activate Bluetooth with “LG XBOOM” App
Radio Operations
– Listening to the radio
– Presetting the Radio Stations
– Deleting all the saved stations
Sound adjustment
– Setting the sound mode
Recording to USB
Other Operations
– Turn off the sound temporarily
– DEMO
– Resume stop
– CHILDSAFE Mode
– Last Scene Memory
– Power Resume - Optional
– System Select - Optional
– Using Microphone
– LIGHTING
– Sleep Timer Setting
– Dimmer
– Auto power down
– AUTO POWER On
– Auto function change
Setting the Clock
– Setting the Clock through “LG XBOOM” App
– Using your player as an alarm clock
LG Sound Sync
WIRELESS PARTY LINK Connection
5
Troubleshooting
52
52
53
Troubleshooting
– General
– NOTES to release Demo mode
6
Appendix
54
Controlling a TV with the Supplied Remote
Control
– Setting up the remote to control your TV
Area Code List
Language code List
Trademarks and Licenses
Maintenance
– Notes on Discs
– Handling the Unit
Specifications
54
55
56
57
58
58
58
59
5
1
2
3
4
5
6
6
Getting Started
Unique Features
1
BLUETOOTH®
Getting Started
Listens to music stored on your Bluetooth device.
AUTO DJ
Blends the end of one song into the beginning of
another for seamless playback.
USB Direct Recording
Records music to your USB device.
LG XBOOM
LG XBOOM is an app designed to let you take
control of some of LG’s latest audio devices. (Page
38-39)
LG Sound Sync
Controls volume level of this unit by the remote
control of your LG TV that is compatible with LG
Sound Sync.
Full HD up-scaling
Views Full HD picture quality with simple setup.
Getting Started
Introduction
Playable Discs
DVD-VIDEO (8 cm/12 cm disc)
Discs such as movies that can be
purchased or rented.
DVD±R (8 cm/12 cm disc)
Video mode and finalized only.
DVD-RW (8 cm/12 cm disc)
Video mode and finalized only.
DVD+R: Video mode only
Supports the double layer disc also.
DVD+RW (8 cm/12 cm disc)
Video mode and finalized only.
Audio CD: Music CDs or CD-R/CDRW in music CD format that can be
purchased.
About the “7” Symbol Display
“7” may appear on your TV display during operation
and indicates that the function explained in this
owner’s manual is not available on that specific
media.
Symbols Used in this Manual
r
DVD-Video, DVD±R/RW in Video
mode or VR mode and finalized
t
Audio CDs
y
Video files contained in the Disc
u
Audio files contained in the Disc
i
Photo files contained in the Disc
,,Note
Indicates special notes and operating features.
>>Caution
Indicates cautions for preventing possible damages
from abuse.
Regional Codes
This unit has a regional code printed on the rear of
the unit. This unit can play only DVD discs labeled
same as the rear of the unit or “ALL”.
yy Most DVD discs have a globe with one or more
numbers in it clearly visible on the cover. This
number must match your unit’s regional code or
the disc cannot play.
yy If you try to play a DVD with a different regional
code from your unit, the message “Check Regional
Code” appears on the TV screen.
1
Getting Started
This unit plays DVD±R/RW and CD-R/RW that
contains audio titles, MP3, WMA and/or JPEG files.
Some DVD±RW/DVD±R or CD-RW/CD-R cannot be
played on this unit due to the recording quality or
physical condition of the disc, or the characteristics of
the recording device and authoring software.
7
8
Getting Started
Playable file
Requirement
1
Getting Started
Music file requirement
MP3/WMA file compatibility with this unit is limited
as follows.
yy Sampling frequency: within 32 to 48 kHz (MP3),
within 32 to 48 kHz (WMA)
yy Bit rate: within 32 to 320 kbps (MP3),
40 to 192 kbps (WMA)
yy Support Version: v2, v7, v8, v9
yy Maximum files: Disc: 999 / USB: 2,000
yy Maximum folders : Disc: 99 / USB: 200
yy File extensions: “.mp3”/ “.wma”
yy Certain MP3/WMA files may not be played
depending on the type or format of the file.
yy CD-ROM file format: ISO 9660/ JOLIET
yy We recommend that you use Easy-CD Creator,
which creates an ISO 9660 file system.
yy A protected file by DRM (Digital rights
management) cannot be played on the unit.
yy The DTS disc is not supported.
You have to set the disc format option to [Mastered]
in order to make the discs compatible with the LG
players when formatting rewritable discs. When
setting the option to Live File System, you cannot use
it on LG players.
(Mastered/Live File System: Disc format system for
Windows Vista)
Photo file requirement
Photo file compatibility with this unit is limited as
follows:
yy Max pixel in width: 2760 x 2048 pixel
yy Maximum files: Under 999
yy Some discs may not operate due to a different
recording format or the condition of disc.
yy File extensions: “.jpg”
yy CD-ROM file format: ISO9660/ JOLIET
Getting Started
Video file requirement
Compatible USB Devices
Video file compatibility with this unit is limited as
follows:
yy MP3 Player: Flash type MP3 player.
yy The file name of the Video subtitle should be
entered within 45 characters.
yy If there is impossible code to express in the Video
file, it may be displayed as “ _ “ mark on the display.
yy Frame rate: less than 30 fps.
yy If the video and audio structure of recorded files is
not interleaved, either video or audio is outputted.
yy Playable Video file: “.avi”, “.mpg”, “.mpeg”
yy Playable Subtitle format: SubRip (*.srt/ *.txt), SAMI
(*.smi), SubStation Alpha (*.ssa/ *.txt), MicroDVD
(*.sub/ *.txt), SubViewer 2.0 (*.sub/ *.txt), Vobsub
(*.sub)
yy Playable Codec format:
“Xvid”, “MPEG-1”, “MPEG-2”
yy Playable Audio format: “AC3”, “PCM”, “MP3”,
“WMA”,
yy Sampling frequency: within 32 to 48 kHz (MP3),
within 32 to 48 kHz (WMA)
yy Bit rate: within 32 to 320 kbps (MP3),
40 to 192 kbps (WMA)
yy For Discs formatted in Live file system, you can not
it on this unit.
yy If the name of movie file is different from that of
the subtitle file, during playback of a Video file,
subtitle may not be display.
yy If you play a Xvid file differ from Xvid spec, it may
not operate normally.
yy If you play GMC video file which is more than
1-warp point, video playback screen will not
smooth.
yy USB Flash Drive:
Devices that support USB2.0 or USB1.1.
yy The USB function of this unit does not support all
USB devices.
USB device requirement
yy Devices which require additional program
installation when you have connected it to a
computer, are not supported.
yy Do not extract the USB device while in operation.
yy For a large capacity USB, it may take longer than a
few minute to be searched.
yy To prevent data loss, back up all data.
yy If you use a USB extension cable or USB hub, the
USB device is not recognized.
yy Using NTFS file system is not supported. (Only
FAT(16/ 32) file system is supported.)
yy This unit recognizes up to 2,000 files.
yy External HDD, Card readers, Locked devices, or
hard type USB devices are not supported.
yy USB port of the unit cannot be connected to PC.
The unit cannot be used as a storage device.
yy Some USB may not work with this unit.
1
Getting Started
yy Available resolution: within 720 x 576 (W x H)
pixels.
9
10 Getting Started
Remote control
• • • • • • • • • • • • • • a• • • • • • • • • • • • • •
1 (Standby): Turns the power on or off.
F (Function): Selects the function and input source.
1
Getting Started
Input source / Function
Disc
Display
DVD/CD
USB
USB
AUX input
AUX
Bluetooth
BT
LG Sound Sync (Wireless)
LG TV
Radio
FM
B (Open/Close): Opens and closes the disc tray.
0-9 numerical buttons: Selects numbered options in
a menu.
AUTO DJ: Selects the AUTO DJ mode. (Page 34)
h REPEAT: Listens to your files/tracks/chapters
repeatedly or randomly.
• • • • • • • • • • • • • • b• • • • • • • • • • • • • •
C/V (Skip): Skips backward or forward.
c/v (Scan): Scans for a section within a track/file/
chapter.
Z (Stop):
-- Stops playback.
-- Cancels DELETE function.
X (Play): Starts playback.
M (Pause): Pauses playback.
SPECIAL EQ: Chooses special equalizer.
VOL (Volume) +/-: Adjusts speaker volume.
MARKER/JUKEBOX:
-- Marks play list. (Page 29)
-- Selects JUKE BOX mode. (Page 33)
Replacement of battery
-- Makes JUKE BOX list.
EQUALIZER: Chooses sound impressions.
[ (Mute): Mutes the sound.
(R03
)
(R03)
Remove the battery cover on the rear of the remote
control, and insert the battery with 4 and 5
matched correctly.
Getting Started
11
• • • • • • • • • • • • • • c• • • • • • • • • • • • • •
• • • • • • • • • • • • • • d• • • • • • • • • • • • • •
! (Home): Displays the [Home Menu] on a DVD/CD
function.
CLOCK: Sets a clock and checks a time.
DISC MENU: Accesses the menu on a DVD disc.
W/S/A/D (up/ down/ left/ right): Used to
navigate on-screen displays.
PRESET/FOLDER +/-:
-- Chooses a preset number for a radio station. (Page
40)
-- Searches for a folder of MP3/WMA files. When a
USB containing MP3/WMA files in several folders
is being played, press PRESET/FOLDER +/- to
select the folder you want to play.
TUNING +/-: Tunes in the desired radio station.
m (Select):
-- Acknowledges menu selection.
-- Presetting the radio stations.
] (Close): Moves backwards in the menu or exits
the setup menu.
m INFO/DISPLAY
-- Accesses On-Screen Display.
-- Sees information about your music (USB). An MP3
file often come with ID3 tag. The tag gives the
Title, Artist, Album or Time information.
-- Sees Bluetooth device name of the unit in BT
READY.
-- Sees the name of connected all Bluetooth device
in Bluetooth mode.
-- When th ese units are successfully connected
each other in WIRELESS PARTY LINK mode, each
of connected device names appears in the each
unit.
CLEAR/DELETE:
-- Removes a number when setting the password.
-- Deletes MP3/WMA files. (USB only). (Page 32)
-- Deletes a song on the JUKE BOX list.
-- Deletes all the saved stations.
SET: Confirms the setting.
?: This button is not available.
VOCAL EFFECTS: Selects various vocal effects mode.
SLEEP: Sets the system to turn off automatically at
a specified time.
(Dimmer: The display window will be darkened by
half.)
USB REC:
-- Records to USB.
-- Stops recording.
MIC (Microphone) ECHO: Selects ECHO mode
VOICE CANCELLER: You can reduce the vocal tones
during music playback from various input sources.
?: This button is not available.
MIC VOL (Microphone Volume) -/+ : Adjusts
microphone volume.
KEY CHANGER (L/l): Changes the key to suit your
vocal range.
TV Control buttons: Controls the TV. (Page 54)
You can control the TV on or off and input source.
1
Getting Started
TITLE: If the current DVD title has a menu, the title
menu appears on the screen. Otherwise, the disc
menu may not appear.
ALARM: With the ALARM function you can turn on
Discs, USB play and tuner reception at a desired time.
12 Getting Started
Front panel
a
1
b
c
d e f
g
h
Getting Started
Getting Started
h B (Open/Close)
a 1 (Standby)
Turns the power on or off.
Opens and closes the disc tray.
F (Function)
MIC VOL (Microphone volume) -/+
Adjust microphone volume.
- Press and hold to adjust delay time when using
PARTY LINK with AUX.
3TWIN
Connects two speakers for TWIN mode in WIRELESS
Input source / Function
Display
Disc
DVD/CD
USB
USB
AUX input
AUX
Bluetooth
BT
LG Sound Sync (Wireless)
LG TV
Radio
FM
b MIC (Microphone) ECHO / DEMO
- Selects ECHO mode.
- In power off status, if you press
MIC ECHO / DEMO, show demo mode.
VOCAL EFFECTS
Selects various vocal effects mode.
LIGHTING
Selects the lighting mode.
c USB Port
You can play sound files by connecting the USB
device.
d Display window
e Disc tray
(Remote sensor)
g N (Play/Pause)
Starts or pauses playback.
C/V (Skip/Scan)
- Skips backward or forward.
- Scans for a section within a track/file/chapter.
- Selects the radio stations.
Z (Stop)
Stops playback or cancels DELETE function.
PARTY LINK.
1
Getting Started
- Selects the function and input source.
VOL (Volume) -/+
Adjusts speaker volume.
f
13
14 Getting Started
Rear panel
a
1
Getting Started
a Power cord
b SERVICE ONLY: S/W download connector.
c HDMI OUT TO TV: Connect to TV.
d MIC (Microphone) jack
e ANTENNA (FM)
f AUX IN (L/R): Connect an auxiliary device.
AUX OUT (L/R): Connect to an input of external
device.
b
c
d e
f
Getting Started
15
Useful functions for using the unit
Function
Description
Initial setting of this function
was set to off.
Auto Power On It allows the unit to turn on
automatically by input signals:
(Page 47)
BT (Bluetooth) or LG TV
Do this
ON
Press and hold Xon the remote control
or N on the unit for 5 seconds in BT
(Bluetooth) function.
OFF
Press and hold Xon the remote control
or N on the unit for 5 seconds in BT
(Bluetooth) function.
ON
Turn off the unit by pressing 1 on the unit
for 5 seconds.
OFF
Turn off the unit by pressing 1 on the unit
for 5 seconds.
1
Getting Started
BT Lock On/Off It allows you to connect a
Bluetooth device only on
(Page 37)
BT (Bluetooth) and LG TV
functions.
To do
16 Connecting
Connections to Your TV
HDMI Out Connection
2
Connecting
If you have a HDMI TV or monitor, you can connect it
to this unit using a HDMI cable (Type A, High Speed
HDMI™ Cable).
Connect the HDMI OUT jack on the unit to the HDMI
IN jack on a HDMI compatible TV or monitor.
Set the TV’s source to HDMI (refer to TV’s Owner’s
manual).
Unit
TV
,,Note
yy You can fully enjoy digital audio and video
signals together with this HDMI connection.
yy When you use HDMI connection, you can
change the resolution for the HDMI output.
(Page 17)
>>Caution
yy Changing the resolution when the connection
has already been established may result in
malfunctions. To solve the problem, turn off
the unit and then turn it on again.
yy When the HDMI connection with HDCP is
not verified, TV screen is changed to black or
green screen or the snow noise may occur
on the screen. In this case, check the HDMI
connection, or disconnect the HDMI cable.
yy Make sure the unit is connected directly to
the TV. Tune the TV to the correct video input
channel.
Connecting 17
,,Note
yy If a connected HDMI device does not accept
the audio output of the unit, the HDMI
device’s audio sound may be distorted or may
not output.
yy When you connect a HDMI or DVI compatible
device make sure of the following:
The unit provides several output resolutions for
HDMI.
You can change the resolution using [Setup] menu.
1. Press ! on the remote control.
2. Use W/S/A/D on the remote control to
select the [Setup] and press m on the remote
control.
The [Setup] menu appears.
- The connected device’s video input is set
correctly for this unit.
- The connected device is compatible with
720 x 480i (or 576i), 720 x 480p (or
576p), 1280 x 720p, 1920 x 1080i or
1920 x 1080p video input.
yy Not all HDCP-compatible HDMI or DVI devices
will work with this unit.
- The picture will not be displayed properly
with non-HDCP device.
- This unit does not playback and TV screen
is changed to black or green screen or the
snow noise may occur on the screen.
yy If there is noise or lines on the screen, please
check the HDMI cable and use a higher
version cable than High Speed HDMI™ Cable.
yy The HDMI sounds output only DVD/CD
function.
2
Connecting
- Try switching off the HDMI/DVI device and
this unit. Next, switch on the HDMI/DVI
device and leave it for around 30 seconds,
then switch on this unit.
Resolution Setting
3. Use W/S on the remote control to select
[Display] option then press D on the remote
control to move to the second level.
4. Use W/S on the remote control to select the
[Resolution] option then press D on the remote
control to move to the third level.
5. Use W/S on the remote control to select the
desired resolution then press m on the remote
control to confirm your selection.
,,Note
yy If your TV does not accept the resolution you
have set on the player, you can set resolution
to 480p (or 576p) as follows: Press Z for
more than 5 seconds.
yy [Home Menu] appears only on DVD/CD
function.
18 Connecting
Optional Equipment
Connection
AUX IN Connection
2
Listening to music from your external
device
The unit can be used to play the music from many
types of external device.
1. Connect the external device to the AUX IN (L/R)
connector of the unit.
Connecting
Connect an output of auxiliary device (Camcorder, TV,
Player, etc) to the AUX IN (L/R) connector.
2. Turn the power on by pressing 1.
If your device has only one output for audio (mono),
connect it to the left audio jack on the unit.
4. Turn on the external device and start it playing.
Red
Unit
White
Audio cable
DVD, Blu-ray player etc.
3. Press F to select AUX.
Connecting 19
AUX OUT Connection
PARTY LINK with AUX
Connect an input of auxiliary device to the AUX OUT
(L/R) connector.
You can connect two units to play music together.
If your device has only one input for audio(mono),
connect it to the left audio jack on the unit.
1. Connect AUX OUT (L/R) connector on a unit to
the AUX IN connector on the other unit using
Audio cable.
2. Press and hold F on the unit connected through
AUX OUT and then select “ON - DELAY”.
“ON - DELAY” appears in the display window and
change to “DELAY time” soon.
When “ON - DELAY” and “DELAY time” are
displayed in the display window, you can adjust
the delay time.
Audio cable
Auxiliary device
,,Note
yy This function is not available on LG TV
function.
yy The initial Delay is 30 ms. If you want to
change the Delay time, press C/Von the
unit. The connected device’s Delay may differ.
If Audio Sync is not matched, adjust Delay of
PARTY LINK with AUX to synchronize sound.
yy It is available to adjust the Delay from
0 ms to 200 ms. Synchronizing tempo is not
available depending on devices.
yy Delay value is saved and PARTY LINK with
AUX is turned off when the unit turns off.
yy You can select ON/OFF - DELAY mode by
pressing and holding F.
yy In case of the microphone,delay setting is not
applied.
2
Connecting
3. Press C/V on the unit to adjust delay setting.
20 Connecting
USB Connection
Antenna Connection
Connect a USB device (or MP3 player, etc.) to the
USB ports on the unit.
Connect the supplied FM antenna for listening to the
radio.
FM antenna
USB device
2
Connecting
,,Note
Removing the USB device from the unit:
1. Choose a different function/mode or press
I twice in a row.
2. Remove the USB device from the unit.
,,Note
Be sure to fully extend the FM wire antenna.
System Setting 21
Adjust the setup
settings
By using the Setup menu, you can make various
adjustments to items such as picture and sound.
To display and exit the Setup
menu
1. Press !on the remote control.
Displays the [Home Menu].
You can also set a language for the subtitles and the
Setup menu, among other things. For details on each
Setup menu item, see pages 21 to 24.
OSD Initial language settings Optional
2. Select an [Setup] by using A/Don the remote
control.
3. Press mon the remote control.
Displays the [Setup].
1. Press 1 to turn the unit on. The language setup
menu will appear on the screen.
About help menu for Setup
2. Use W/S/A/D on the remote control to
select a language then press m on the remote
control.
The confirm menu will appear.
3. Use A/D on the remote control to select the
[Enter] then m on the remote control to finish
the language setup.
3
4. Press !on the remote control or ] on the
remote control to exit in the [Setup] Menu.
Menu
Buttons
Operation
W/S
Move
W/S
Moving to another
menu.
A
Move
A
Moving to previous
level.
D
Move
D
Moving to next level
or selecting menu.
]
To exit the [Setup]
menu.
m
To confirm menu.
]
Close
m
Select
,,Note
[Home Menu] appears only on DVD/CD function.
System Setting
During the first use of this unit, the initial language
setup menu appears on your TV screen. You must
complete initial language selection before using the
unit. English will be selected as the initial language.
22 System Setting
Language
Display Mode
Menu Language
The Display Mode setting works only when the TV
Aspect mode is set to 4:3.
Select a language for the Setup menu and on screen
display.
Disc Audio / Disc Subtitle / Disc Menu
Select the language you prefer for the audio track
(disc audio), subtitles, and the disc menu.
[Original]
Refers to the original language in which the disc
was recorded.
3
[Letterbox]
Displays a wide picture with bands on the upper
and lower portions of the screen.
[Panscan]
Automatically displays the wide picture on the
entire screen and cuts off the portions that do
not fit. (If the disc/file is not compatible with Pan
Scan, the picture is displayed at Letterbox ratio.)
System Setting
[Other]
Resolution
To select another language, press numeric
buttons and then m on the remote control
to enter the corresponding 4-digit number
according to the language code list on the page
56.
If you enter the wrong language code, press
CLEAR/DELETE on the remote control.
Sets the output resolution of HDMI video signal.
Refer to “Resolution Setting” for details about the
resolution (page 17).
[Off (for Disc Subtitle)]
Turns off Subtitle.
[Auto]
If the HDMI jack is connected to TVs providing
display information (EDID), automatically selects
the resolution best suited to the connected TV.
[1080p]
Outputs 1080 lines of progressive video.
Display
TV Aspect
Select the screen aspect to use based on the shape
of your TV screen.
[4:3]
Select when a standard 4:3 TV is connected.
[16:9]
Select when a 16:9 wide TV is connected.
[1080i]
Outputs 1080 lines of interlaced video.
[720p]
Outputs 720 lines of progressive video.
[480p (or 576p)]
Outputs 480 (or 576) lines of progressive video.
[480i (or 576i)]
Outputs 480 (or 576) lines of interlaced video.
System Setting 23
Audio
DRC (Dynamic Range Control)
Make the sound clear when the volume is turned
down and prevent a sudden sound increase (Dolby
Digital only). Set to [On] for this effect.
HD AV Sync
3
System Setting
Sometimes Digital TV encounters a delay between
picture and sound. If this happens you can
compensate by setting a delay on the sound so that
it effectively ‘waits’ for the picture to arrive: this is
called HD AV Sync. Use W/S on the remote control
to scroll up and down through the delay amount,
which you can set at anything between 0 and
300ms.
24 System Setting
Lock (Parental Control)
Initial Setting the Area Code
When you use this unit for the first time, you have to
set the Area Code.
1. Select the [Lock] menu and then press D on the
remote control.
3
System Setting
2. Press D on the remote control.
To access the [Lock] options, you must input the
password you have created.
Input a password and press m on the remote
control. Enter it again and press mon the remote
control to verify.
If you make a mistake before pressing mon the
remote control, press CLEAR/DELETE on the
remote control.
Password
You can enter or change password.
1. Select [Password] on the [Lock] menu and then
press Don the remote control.
2. Press mon the remote control.
3. Input a password and press mon the remote
control.
To change the password, press mon the remote
control when the [Change] option is highlighted.
Input a password and press mon the remote
control.
Enter it again and press mon the remote control
to verify.
4. Press ! on the remote control to exit the menu.
,,Note
3. Select the first character using W/Son the
remote control.
If you forget your password, you can clear it
using the following steps:
4. Press mon the remote control and select the
second character using W/Son the remote
control.
1. Select the [Setup] menu on the
[Home Menu].
5. Press mon the remote control to confirm your
Area code selection.
Rating
Blocks playback of rated DVDs based on their
contents. Not all discs are rated.
1. Select [Rating] on the [Lock] menu then press D
on the remote control.
2. Input a password and press m on the remote
control.
3. Select a rating from 1 to 8 using the W/Son
the remote control.
[Rating 1-8]
Rating one (1) has the most restrictions and
rating eight (8) is the least restrictive.
[Unlock]
If you select unlock, parental control is not active
and the disc plays in full.
4. Press m on the remote control to confirm your
rating selection.
2. Input the 6-digit number “210499” and
pressmon the remote control.
The password is cleared.
Area Code
Enter the code of the area whose standards were
used to rate the DVD video disc, based on the list on
page 55.
1. Select [Area Code] on the [Lock] menu then
press D on the remote control.
2. Input a password and press mon the remote
control.
3. Select the first character using W/S on the
remote control.
4. Press m on the remote control and select the
second character using W/S on the remote
control.
5. Press m on the remote control to confirm your
Area code selection.
Operating 25
Using the Home Menu
1. Press !on the remote control.
Displays the [Home Menu].
2. Select an option by using A/D on the remote
control.
3. Press m on the remote control then selected
option menu.
[Music] – Displays [MUSIC] menu.
[Movie] – Start video media’s playback or displays the
[MOVIE] menu.
[Photo] – Displays [PHOTO] menu.
[Setup] – Displays the [SETUP] menu.
yy USB function is only available on music
playback.
Operating
,,Note
yy [Home Menu] appears only on DVD/CD
function.
4
26 Operating
Basic Operations on
Disc
To
1. Insert the disc by using the B.
2. Press ! on the remote control.
Displays the [Home Menu].
3. Select an option by using A/D on the remote
control.
Playing
repeatedly or
randomly
Stop
4
Press Z.
Operating
Press X on the remote control
or N on the unit.
Pause
Press M on the remote control
or N on the unit.
Frame-byFrame playback
Press M on the remote control
repeatedly to play title Frameby-Frame. (DVD Movie title,
Movie file only)
Skipping to the
next/ previous
chapter/ track/
file
Locating a
point quickly by
playing a file in
fast forward or
fast reverse
During playback, press C/
V to go to the next chapter/
track/ file or to return to
the beginning of the current
chapter/ track/ file.
Press C twice briefly to step
back to the previous chapter/
track/ file.
During playback, press c/v
on the remote control or press
and hold C/V on the unit
repeatedly to select the required
scan speed.
To return to normal speed,
press X on the remote control
or N on the unit.
- DVD: Chapter/ Title/ Off
-A
udio CD/ MP3/ WMA: Track/
All/ Random/ Off
Do this
Playback
Press h REPEAT on the
remote control repeatedly,
and the current title, chapter
or track will be played back
repeatedly or randomly.
- Video(MOVIE): Title/ All/ Off
4. Press m on the remote control then selected
option menu.
To
Do this
Slowing down
the playing
speed
Selecting
a track/file
directly
In the pause mode, Press c/
v on the remote control or
press and hold C/V on the
unit repeatedly to select the
required speed. (DVD Movie
title only)
In the pause mode, press
v on the remote control
or press and hold V on the
unit repeatedlyl to select the
required speed. (Movie file only)
Press 0 to 9 numerical buttons
on the remote control to go to
the desired file or track directly.
Operating 27
Advanced Operations on
Disc
To display the DVD title
Displaying Disc Information
on-screen
1. Press TITLE on the remote control.
The disc’s title appears.
You can display various information about the disc
loaded on-screen.
r
When you play a DVD which contains several title,
you can select the title you want using the Menu.
2. Select the menu by pressing W/S/A/D on
the remote control.
3. Press m on the remote control to confirm.
1. Press m INFO/DISPLAY on the remote control
to show various playback information.
The displayed items differ depending on the disc
type or playing status.
1.5 times speed playback
2. You can select an item by pressing W/Son the
remote control and change or select the setting
by pressing A/D on the remote control.
The 1.5 speed allows you to watch the pictures and
listen to the sound quicker than playing at a normal
speed.
Title – C
urrent title number/ total number of titles.
Chapter – C
urrent chapter number/ total number of
chapters.
1. During playback, press X on the remote control
to play at 1.5 times speed.
“dX1.5” appears on the screen.
Time – Elapsed playing time.
2. Press X on the remote control again to exit.
Subtitle – Selected subtitle.
Angle – Selected angle/ total number of angles.
,,Note
If any button is not pressed for a few seconds,
the on-screen display disappears.
To display the DVD Menu
r
When you play a DVD which contains several menu,
you can select the menu you want using the Menu.
1. Press DISC MENU on the remote control.
The disc’s menu appears.
2. Select the menu by using W/S/A/D on the
remote control.
3. Press m on the remote control to confirm.
Screen Saver
The screen saver appears when you leave the unit in
Stop mode for about five minutes.
4
Operating
Audio – Selected audio language or channel.
r
28 Operating
Starting play from selected time
Resume playback
ry
ryut
To start playing at any chosen time on the file or title.
The unit records the point where you pressed the Z
depending on the disc.
If “MZ (Resume Stop)” appears on the screen briefly,
press X on the remote control or N on the unit to
resume playback
(from the scene point).
1. Press m INFO/DISPLAY on the remote control
during playback.
2. Press W/S on the remote control to select the
time clock icon and “--:--:--” appears.
3. Input the required start time in hours, minutes,
and seconds from left to right.
If you enter the wrong numbers, press CLEAR/
DELETE on the remote control to remove the
numbers you entered.
Then input the correct numbers.
For example, to find a scene at 1 hour,
10 minutes, and 20 seconds, enter “11020” by
using numerical buttons on the remote control.
If you press Z twice or unload the disc,
“Z”(Complete Stop) appears on the screen.
The unit will clear the stopped point.
,,Note
yy The resume point may be cleared when a
button is pressed (for example; 1, B, etc).
yy This function may not work on some disc or
title/track.
4. Press m on the remote control to confirm.
Playback starts from the selected time.
4
Changing subtitle code page
Operating
y
If the subtitle is not displayed properly, you can
change the subtitle code page to view the subtitle file
properly.
1. During playback, press m INFO/DISPLAY on the
remote control to display the On-Screen display.
2. Use W/S on the remote control to select the
[Code Page] option.
3. Use A/D on the remote control to select
desired code option.
4. Press ] on the remote control to exit the OnScreen display.
Operating 29
Marked Playback
ut
The mark function enables you to store your
favourite files from any disc in the unit memory.
1. Select [Music] on the [Home Menu].
Returning to the upper folder.
(MP3/ WMA only)
File information will be displayed
according to the ID3 TAG information
on the appropriate music file. (MP3
only)
To delete a Marker
1. Use W/S on the remote control to select the
track that you wish to erase from the marked file.
2. Press MARKER/JUKEBOX on the remote control.
To delete all Markers
Use W/S/A/D on the remote control to select
[Deselect All] then press m on the remote control in
program edit mode.
,,Note
The markers are also cleared when the disc is
removed, the unit is switched to power off or
the function is switched to others.
4
Deselecting all tracks/files.
Moving to the previous or next
file list.
2. Select a desired music on the [List] by using the
W/S on the remote control then press
MARKER/JUKEBOX on the remote control to
appears the mark on the list.
3. Press mon the remote control.
Displays the play mode.
4. Select the play mode by using the W/S on the
remote control and press mon the remote
control.
[Mark Play]
Marked playback.
[Current Play]
Normal playback.
,,Note
If you want to select all files on the list, select
[Select All] and press m on the remote control.
Operating
Selecting all tracks/files.
30 Operating
Viewing a PHOTO file
About help menu in the full screen
i
Menu
Buttons
This unit can play discs with photo files.
m
Menu
m INFO/
DISPLAY
Displaying the Option
menu.
a/d
Prev./ Next
A/D
Moving to another file.
]
List
]
1. Select [Photo] on the [Home Menu] and press
m on the remote control
Moving to the previous or next
file list.
Operation
Returning to the
[Photo] menu.
Options while viewing a photo
You can use various options during viewing a photo in
full screen.
1. While viewing a photo in full screen, press
m INFO/DISPLAY on the remote control to
display the option menu.
4
2. Select an option using W/S/A/D on the
remote control.
Returning to the upper
folder.
Operating
2. Press W/S on the remote control to select a
folder, and then press mon the remote control.
3. If you want to view a slide show, press W/Son
the remote control to highlight a file and press
Xon the remote control.
About help menu in the [Photo] menu
Menu
Buttons
d Slide
Show
X
W/S/
A/D
Move
W/S/A/D
m
Select
]
Close
Operation
Viewing a slide
show.
Moving to another
file or content.
a
b
c
d
e
a Current photo/ Total number of photos –
Use A/D on the remote control to view
previous/next photo.
b Slide Show d/M – Press m on the remote
control to start or pause slide show.
m
Viewing a
particular file.
c Speed x3/ x2/ x1 – Use m on the remote
control to select a delaying speed between
photos in a slide show.
]
Returning to the
[Home Menu].
d Rotate – Press m on the remote control to
rotate the photo.
e Go to list – Press m on the remote control to
return [Photo] menu.
Operating 31
Basic Operations on
USB
1. Connect the USB device to the USB port.
2. Select USB function by pressing F.
To
Stop
Do this
Press Z.
Press X on the remote control or
Playback
N on the unit
Press M on the remote control or N
Pause
on the unit.
Press and hold C/V or c/
Scanning for a
v on the remote control during
section within
playback and release it at the point
a file
you want to listen to.
-- In stop status,
Press C/V to go to the next/
previous file.
Skipping to -- During playback,
the next/ Press V to go to the next file.
previous file
Playing in less than 3 seconds, press
C to go to the previous file.
Playing after 3 seconds, press C to
go to the beginning of the file.
Playing
Press h REPEAT on the remote
repeatedly or control repeatedly. Refer to the note
randomly for details about the display change.
yy Repeat/Shuffle playback operates as follows.
On Diplay
Description
OFF
Plays songs in order and stops
the playback.
ONE
Plays a same song repeatedly.
FOLDER
Plays songs in a folder repeatedly.
ALL
Plays all the songs on repeatedly.
SHUFFLE
Plays all the songs once randomly,
and stops the playback.
yy When you play JUKE BOX list, only ONE and
ALL are available.
yy Even after restarting the unit or switching
one function to another, you can listen to
music from the point where it’s last been
played.
yy USB function is only available on music
playback.
4
Operating
Press 0 to 9 numerical buttons on
Selecting a file
the remote control to go to the
directly
desired file directly.
,,Note
32 Operating
Selecting a folder and
an MP3/WMA file
1. Press PRESET/FOLDER +/- on the remote
control repeatedly until a desired folder appears.
2. Select the file you want by using C/V.
3. Press X on the remote control or N on the unit.
,,Note
yy USB Folders/Files are recognized as below.
*
Deleting a file/folder or format
You can delete file, folder on your USB or format the
USB.
1. Select USB function by pressing F.
2. Press CLEAR/DELETE on the remote control
repeatedly, the display changes as followings.
DEL FILE DEL DIR FORMAT
On Display
Description
DEL FILE
Select the file you want to delete
DEL DIR
Select the folder you want to
delete
FORMAT
Select to format the USB device.
If you want to exit the current mode, press Z.
3. To delete file/folder or format, press and hold
CLEAR/DELETE on the remote control.
>>Caution
4
Operating
yy Do not extract the USB device during
operation. (play, delete, etc.)
yy Regular back up is recommended to prevent
data loss.
yy The delete function may not be supported
according to the USB status. (lock, etc.)
yy If there is no file in a folder, the folder will not
appear.
yy Folders will be presented as the following
order;
ROOT FOLDER 1 FOLDER 3
FOLDER 7 FOLDER 8 FOLDER 5
FOLDER 6
yy File will be played from $ file No.1 to $ file
No.14 one by one.
yy Files and folders will be presented in order
recorded and may be presented differently
according to the record circumstances.
*ROOT: The first screen you can see when a
computer recognize the USB is “ROOT”.
Operating 33
Advanced Operations on
USB
Editing JUKE BOX
JUKE BOX Playback
2. Press PRESET/FOLDER +/- on the remote
control to select a file to edit.
JUKE BOX function enables you to make a playlist of
your favorite files from a USB. A playlist of up to 100
files can be entered.
1. Press and hold MARKER/JUKEBOX on the
remote control to enter the edit mode.
(Playing will be stopped when you press
MARKER/JUKEBOX on the remote control.)
3. Press C/V on the remote control.
4. Press MARKER/JUKEBOX on the remote control.
5. Repeat 2 to 4 to store the other files.
Making JUKE BOX list
1. Press and hold MARKER/JUKEBOX on the
remote control to enter the edit mode.
(Playing will be stopped when you press
MARKER/JUKEBOX on the remote control.)
2. Select a file by pressing C/V on the remote
control.
3. Press MARKER/JUKEBOX on the remote control
to save the file.
To play the JUKE BOX list, press X on the remote
control after you edit the list.
Deleting JUKE BOX list
Deleting function only works in the edit mode.
1. Press and hold MARKER/JUKEBOX on the
remote control to enter the edit mode.
Or
Press CLEAR/DELETE on the remote control
while JUKE BOX is played to enter the edit mode.
5. Press MARKER/JUKEBOX on the remote control
once again.
2. Select a song by pressing PRESET/FOLDER +/on the remote control repeatedly.
To play the JUKE BOX list, press X on the remote
control after you make the list.
3. Press CLEAR/DELETE on the remote control
while a song is selected.
,,Note
When making or modifying the JUKE BOX list,
REPEAT mode is off.
Enjoying JUKE BOX
Press MARKER/JUKEBOX on the remote control
once. “ON - JUKE BOX” appears on the display
window.
To play JUKE BOX list, press X on the remote control.
To cancel it, press MARKER/JUKEBOX on the remote
control once.
“OFF - JUKE BOX” appears on the display window.
,,Note
yy If there is no JUKE BOX list, “NO PROG”
appears on the display window when you
press MARKER/JUKEBOX on the remote
control.
yy JUKE BOX is switched off in the case below.
-- Changing to a different function.
-- Turning off and on the unit.
-- Operating the numerical buttons on the
remote control.
yy JUKE BOX list is cleared in the case below.
-- Removing the USB device.
-- Deleting or recording music files in the USB
device.
4
Operating
4. Repeat steps 2 - 3 to store other files.
(You can modify the list by pressing PRESET/
FOLDER +/- on the remote control to select the
JUKE BOX program number.)
6. Press MARKER/JUKEBOX on the remote control
once again.
34 Operating
Playback Effect
AUTO DJ
Auto DJ blends the end of one song into the
beginning of another for seamless playback. It
equalizes volume across tracks/files for uninterrupted
playback.
Press AUTO DJ on the remote control repeatedly, the
display changes as followings.
RANDOM (SHUFFLE)
4
SEQUENTIAL
OFF
Operating
On Display
Description
OFF
-
RANDOM
(SHUFFLE)
The music is played randomly on
this mode.
SEQUENTIAL
The music is played repeatedly
on this mode.
,,Note
yy AUTO DJ mode does not support searching
for a section within a track/file or to play
repeatedly or randomly.
yy If you move to other functions or stop the
music using Z on AUTO DJ mode, AUTO DJ
will be disabled.
yy AUTO DJ is not supported in the music file
whose length is less than 60 seconds.
yy Only SEQUENTIAL is selected when played
JUKE BOX list.
yy In USB function, SHUFFLE displays instead of
RANDOM.
Operating 35
Using BLUETOOTH®
wireless technology
Listening to music stored on the
Bluetooth devices
Pairing your unit and Bluetooth device
About Bluetooth
Bluetooth is wireless communication technology for
short range connection.
The sound may be interrupted when the connection
interfered by the other electronic wave or you
connect the Bluetooth in the other rooms.
Connecting individual devices under Bluetooth
wireless technology does not incur any charges.
A mobile phone with Bluetooth wireless technology
can be operated via the Cascade if the connection
was made via Bluetooth wireless technology.
yy Available Devices: Smart phone, MP3, Notebook,
etc.
yy Version: 4.0
yy Codec: SBC, AAC
In order to use Bluetooth wireless technology,
devices must be able to interpret certain profiles.
This unit is compatible with following profile.
A2DP (Advanced Audio Distribution Profile)
1. Turn on the unit.
,,Note
When Bluetooth connection lock is activated,
you can search Bluetooth device in BT function.
2. Operate the Bluetooth device and perform the
pairing operation. When searching for this unit
with the Bluetooth device, a list of the devices
found may appear in the Bluetooth device display
depending on the type of Bluetooth device. Your
unit appears as “LG OL45D (XX)”.
,,Note
yy XX means the last two digits of
Bluetooth address. For example, if your
unit has a Bluetooth address such as
9C:02:98:4A:F7:08, you will see
“LG OL45D (08)” on your Bluetooth device.
yy Depending on the Bluetooth device type,
some devices have a different pairing way. For
details about Bluetooth pairing, refer to your
Bluetooth device manual.
yy You can connect this unit with up to 3
Bluetooth devices simultaneously using the
same method as described above, only in the
Bluetooth function.
yy The multi phone pairing connection is only
supported on Android devices. (Multi phone
pairing connection may not be supported
depending on the connected device
specifications.)
yy Removable/detachable Bluetooth devices
(Ex: Dongle etc.) will not support multi phone
pairing.
4
Operating
Bluetooth Profiles
Before you start the pairing procedure, make sure the
Bluetooth feature is activated on your Bluetooth
device. Refer to your Bluetooth device’s user guide.
Once a pairing operation is performed, it does not
need to be performed again.
36 Operating
3. When this unit is successfully connected with
your Bluetooth device, “PAIRED” appears on the
display window and change to Bluetooth device
name soon. Then “BT” will appear on the display
window.
,,Note
yy “PAIRED” will momentarily appear on the
display when you connect other devices for
multi phone pairing.
yy If the device name is unavailable, “_” will be
displayed.
4. Listen to music.
To play a music stored on your Bluetooth device,
refer to your Bluetooth device’s user guide.
,,Note
4
Operating
yy When using Bluetooth technology, you have
to make a connection between the unit and
the Bluetooth device as close as possible and
keep the distance.
However, it may not work well in certain
situations as described below:
-- There is an obstacle between the unit and
the Bluetooth device.
-- There is a device using same frequency
with Bluetooth technology such as a
medical equipment, a microwave or a
wireless LAN device.
yy If Bluetooth connection does not work well,
try pairing it again.
yy Even if this unit is connected to up to 3
Bluetooth devices in the Bluetooth mode,
you can play and control music by using only
one of the connected devices.
,,Note
yy The sound may be interrupted when the
connection has interference from other
electronic devices.
yy Depending on the type of the device, you may
not be able to use the Bluetooth function.
yy You can enjoy wireless system using phone,
MP3, Notebook, etc.
yy The more distance between the unit and the
Bluetooth device, the lower the sound quality
becomes.
yy Bluetooth connection will be disconnected
when the unit is turned off or the Bluetooth
device gets too far from the unit.
yy When Bluetooth connection is disconnected,
connect the Bluetooth device to the unit
again.
yy When a Bluetooth device is not connected,
“BT READY” appears on the display window.
yy When you use the Bluetooth function,
adjust the volume to a proper level on the
Bluetooth device.
yy When you connect Bluetooth device (iOS
device etc.) to this unit or operate the device,
the volume level can be synchronized with
each other.
yy Bluetooth connection will be disconnected
when you change the Bluetooth function to
some other function. In “LG XBOOM” app
connection, only one device which you are
playing keeps Bluetooth connection. You can
control the Bluetooth device with this unit
but you cannot use sound output.
yy When entering the Bluetooth function,
this unit automatically connects to the last
connected Bluetooth device or the device
which played back last.
(Auto connection may not be supported
depending on the connected device
specifications.)
Operating 37
Controls connected Bluetooth device
You can control connected Bluetooth device by the
unit; play, pause, stop, skip.
,,Note
yy Only Android OS and iOS is available to use
this function.
yy This function may not be supported
depending on the Bluetooth device, or
operated differently.
Bluetooth connection lock (BT LOCK)
You can limit Bluetooth connection to only
BT (Bluetooth) and LG TV function to prevent
unintended Bluetooth connection.
To turn this function on, press and hold Xon the
remote control or N on the unit for 5 seconds in BT
(Bluetooth) function.
“ON-BT LOCK” appears then you can limit Bluetooth
connection.
“OFF-BT LOCK” appears.
,,Note
Even if you set up Bluetooth connection lock to
On, this unit turns on by Auto Power function.
Turn off Auto Power function to prevent it. (Page
47)
Operating
To turn this function off, press and hold Xon the
remote control or N on the unit for 5 seconds in BT
(Bluetooth) function.
4
38 Operating
Using the LG XBOOM
App
,,Note
yy Only Android OS is available to use “LG
XBOOM” app with this unit.
yy It is recommended to use the latest version
of app.
Install “LG XBOOM” App onto
Your Bluetooth Device
There are two ways to install “LG XBOOM” App onto
Your Bluetooth Device.
Install “LG XBOOM” App through QR
code
1. Install “LG XBOOM” app through QR code. Use
the scanning software to scan the QR code.
About “LG XBOOM” App
“LG XBOOM” app brings a suite of new features to
this unit.
To enjoy more features, you are recommended to
download and install free “LG XBOOM” app.
Below introduces you to a feature of “LG XBOOM”
app.
4
Operating
Multi Juke box: Your entertainment increases three
fold when you connect up to 3 Bluetooth phones
at the same time. Play music from three phones and
create a customized playlist from all phones.
2. Tap an icon for installation.
,,Note
yy Make sure that your Bluetooth device is
connected to the Internet.
yy Make sure that your Bluetooth device
has a scanning software application. If you
don’t have one, download one from “Google
Android Market (Google Play Store)”.
yy Depending on the area, QR code may not
work.
yy You can find the available application of this
unit by using “LG Audio” app.
-- Android O/S: Ver 5.0 (or later)
Operating 39
Install “LG XBOOM” App through
“Google Android Market (Google Play
Store)”
1. Tap the “Google Android Market (Google Play
Store)” icon.
2. In the search bar, type in the “LG XBOOM” and
search it.
3. In the search result list, find and tap “LG XBOOM”
to start downloading Bluetooth app.
4. Tap an icon for installation.
,,Note
yy Make sure that your Bluetooth device is
connected to the Internet.
yy Make sure that your Bluetooth device is
equipped with “Google Android Market
(Google Play Store)”.
Activate Bluetooth with “LG
XBOOM” App
“LG XBOOM” app helps to connect your Bluetooth
device to this unit.
Tap “LG XBOOM” app icon on the home screen to
open “LG XBOOM” app, and go to the main menu.
,,Note
yy “LG XBOOM” app will be available in the
software version as follow;
-- Android O/S: Ver 5.0 (or later)
yy If you use “LG XBOOM” app for operation,
there would be some differences between
“LG XBOOM” app and the supplied remote
control. Use the supplied remote control as
necessary.
yy Depending on the Bluetooth device, “LG
XBOOM” app may not work.
yy If you operate the other applications or
change the settings on your Bluetooth
device while using “LG XBOOM” app, “LG
XBOOM” app may operate abnormally.
yy When “LG XBOOM” app operates abnormally,
check your Bluetooth device and the
connection of “LG XBOOM” app and then try
to connect again.
yy Depending on the smart phone's operating
system, you have some differences for “LG
XBOOM” operation.
yy Check Bluetooth setting on your Bluetooth
device if “LG XBOOM” app connection does
not work well.
4
Operating
yy After connection of “LG XBOOM” app, music
may be output from your Bluetooth device.
In this case, try connecting procedure again.
40 Operating
Radio Operations
Presetting the Radio Stations
Be sure that FM antenna is connected. (Page 20)
Before tuning, make sure to turn down the volume.
Listening to the radio
1. Press F until FM appears in the display window.
The last received station is tuned in.
2. Auto tuning:
Press and hold TUNING-/+ on the remote
control or C/V on the unit until the frequency
indication starts to change, then release. Scanning
stops when the unit tunes in a station.
Or
Manual tuning:
Press TUNING-/+ on the remote control or C/
V on the unit repeatedly.
3. Adjust the volume by pressing VOL +/-.
You can preset 50 stations for FM.
1. Press F until FM appears in the display window.
2. Select the desired frequency by pressing
TUNING-/+ on the remote control or C/V on
the unit.
3. Press m on the remote control. A preset number
will blink in the display window.
4. Press PRESET/FOLDER +/- on the remote
control to select the preset number you want.
5. Press m on the remote control. The station is
stored.
6. Repeat steps 2 to 5 to store other stations.
7. To listen a preset station, press PRESET/FOLDER
+/- or 0 to 9 numerical buttons on the remote
control.
4
Deleting all the saved stations
Operating
1. Press CLEAR/DELETE on the remote control.
“DEL ALL” will flash up on the display window
2. Press CLEAR/DELETE on the remote control to
erase all the saved radio stations.
“DELETED ALL” will scroll and on the display
window.
Operating 41
Sound adjustment
Setting the sound mode
This system has a number of pre-set equalizers. The
displayed items for the equalizer may be different
depending on sound sources and effects.
You can select a desired sound mode by using
EQUALIZER on the remote control.
On Display
BASS (BASS BLAST)
or
BASS+ (BASS BLAST+)
Reinforces the bass
and powerful sound.
This program lends
an enthusiastic
atmosphere to the
sound, giving you the
feeling you are at an
actual rock, pop, jazz or
classic concert.
FOOTBALL
You can enjoy the
equalizer FOOTBALL
STADIUM.
STANDARD
You can enjoy
optimized sound.
On Display
FUNK, REGUETON,
SAMBA,
MERENGUE, AXE,
SALSA, SERTANEJ,
FORRO
ARABIC
DANGDUT
Region
Description
Latin
America
Optimized
equalizer
for the
Middle East music genre
prefered in
Indonesia
each region.
AFRO
Africa
INDIA
India
4
Operating
POP
CLASSIC
ROCK
JAZZ
Description
You can select a desired sound mode by using
SPECIAL EQ on the remote control.
42 Operating
Recording to USB
You can record a various sound source to USB.
(DVD/CD, AUX, FM)
1. Connect the USB device to the unit.
2. Press F to select a function you want to record.
3. Start the recording by pressing USB REC on the
remote control.
Function
Result
DVD/CD,
Recorded until stop
AUX, FM
To stop recording
To stop recording, press USB REC on the remote
control.
To select recording bit rate
4
1. Press and hold USB REC on the remote control
for 3 seconds.
Operating
2. Press C/V to select a bit rate.
3. Press USB REC on the remote control to finish
the setting.
The making of unauthorized copies of copyprotected material, including computer
programs, files, broadcasts and sound recordings,
may be an infringement of copyrights and
constitute a criminal offense.
This equipment should not be used for such
purposes.
Be responsible
Respect copyrights
,,Note
yy When you stop recording, the file that has
been recorded at that time will be stored.
yy Do not remove the USB device or turn off
the unit during USB recording. If does not, an
incomplete file may be made and not deleted
on PC.
yy If USB recording does not work, the message
like “NO USB”, “ERROR”, “USB FULL”, “NOT
SUPPORT” or “FILE MAX” is displayed on the
display window.
yy Multi card reader device or external HDD can
not be used for USB recording.
yy A file is recorded by about 512 Mbyte when
you record for a long term.
yy You can control recorded microphone sound
according to microphone volume.
yy You may not store more than 2,000 files.
yy When you are recording during playback, the
sound now playing is output.
yy VOICE CANCELLER or KEY CHANGER
will be reset, if you use recording function
during operating VOICE CANCELLER or KEY
CHANGER.
yy VOICE CANCELLER or KEY CHANGER can
not be operated during recording.
yy It’ll be stored as follows.
DVD/CD
%*4$@3&$
"6%*0@
"6%*0@
Tuner
$%@3&$
53"$,@
53"$,@
The other source*
05)&34@3&$
"6%*0@
"6%*0@
*: AUX and the like.
Tuner: The current recording frequency is shown.
Operating 43
Other Operations
Turn off the sound temporarily
Press [on the remote control to mute your sound.
You can mute your unit, for example, to answer the
telephone, the “MUTE” will appear in the display
window.
To cancel it, press [on the remote control again or
change the volume level.
DEMO
In the power off state, press MIC ECHO / DEMO on
the unit once. The unit will power on and display the
each of functions in the display window.
To cancel the DEMO function, press MIC ECHO /
DEMO on the unit once more.
CHILDSAFE Mode
This function helps to prevent you from being
surprised when you turn on the unit in case that the
volume of the unit is set at a high level.
To turn on CHILDSAFE mode, press and hold Z on
the unit when the volume of the unit is “MIN”.
In CHILDSAFE mode, the volume increase gradually.
To turn off CHILDSAFE mode, press and hold Z on
the unit when the volume of the unit is “MIN” and
this mode is turned on.
,,Note
In case of USB or BT (Bluetooth) function,
CHILDSAFE mode does not work after about
2 minutes from power on the unit even if this
mode is enabled.
Last Scene Memory
r
The unit records the point where you pressed Z
depending on the disc or USB.
This unit memorizes last scene from the last disc that
is viewed. The last scene remains in memory even if
you remove the disc from the unit or switch off the
unit. If you load a disc that has the scene memorized,
the scene is automatically recalled.
If you press Z twice, the unit will clear the stopped
point.
Power Resume - Optional
r
Even if the power suddenly goes out, turn on the
unit and then it plays a position where the contents
is being played. System will periodically save current
playback status.
System Select - Optional
You must select the appropriate system mode for
your TV system. Press and hold M on the remote
control for more than five seconds to be able to
select a system in the
[Home Menu]. (NTSC
PAL)
,,Note
If the USB device is connected or a disc is
inserted, this function is not operated.
4
Operating
Resume stop
44 Operating
Using Microphone
VOICE CANCELLER
1. Connect your microphone to the MIC jack.
You can reduce the vocal tones during music playback
from various input sources.
2. Play the music you want.
3. Sing along with the accompaniment. Adjust the
microphone volume by pressing MIC VOL -/+.
,,Note
yy When not using the microphone, set the MIC
volume to minimum or turn off the MIC and
remove the microphone from the MIC jack.
yy If the microphone is set too near the speaker,
a howling sound may be produced. In this
case, move the microphone away from the
speaker or decrease the sound level by using
the MIC VOL -.
yy If sound through the microphone is extremely
loud, it may be distorted. In this case, set the
microphone volume by pressing MIC VOL -.
4
Operating
yy You can give an echo effect to the sound
from the microphones by pressing
MIC ECHO on the remote control or MIC
ECHO / DEMO on the unit.
Press the VOICE CANCELLER on the remote control
and “ON-VOICE CANCELLER” will appear in display
window.
To cancel it, press VOICE CANCELLER on the remote
control again.
The quality of the VOICE CANCELLER may be
different depending on the recording conditions of
music files.
,,Note
yy This function is available in the DVD/CD, USB
or BT (Bluetooth) Function.
yy If the function is not available, “NOT
SUPPORT” appears in the display window.
yy This function is available to use only when a
microphone is connected.
yy If a microphone is not connected, “INSERT
MIC” appears in the display window.
yy It is not available on the mono source.
yy To initialize it, change the function or
disconnect the microphone.
yy This function may not be initialized depending
on the status of connected devices.
Operating 45
KEY CHANGER
VOCAL EFFECTS
You can adjust the key to 9 steps (4 steps higher, 4
steps lower and the original key).
When you connect your microphone to the MIC jack,
you can enjoy karaoke function by changing voice in
the various source.
yy To make key more sharp, one by one, press the
KEY CHANGER(L) on the remote control
repeatedly during playback.
yy To make the key more flatten, one by one, press
the KEY CHANGER(l) on the remote control
repeatedly during playback.
,,Note
yy This function is available in the DVD/CD, USB
or BT (Bluetooth) Function.
yy To initialize it, change the function, disconnect
the microphone or change the music.
To select various vocal effects mode, pressing VOCAL
EFFECTS repeatedly when vocal effects mode
appears in the display window.
BASS SOPRANO HELIUM ROBOT
DUET MAN DUET WOMAN BASS ECHO1
SOPRANO ECHO1 HELIUM ECHO1
ROBOT ECHO1 DUET MAN1 DUET
WOMAN1 BASS ECHO2 SOPRANO
ECHO2 HELIUM ECHO2 ROBOT ECHO2
DUET MAN2 DUET WOMAN2 OFF
,,Note
yy If a microphone is not connected, “INSERT
MIC” appears in the display window.
yy If the function is not available, “NOT
SUPPORT” appears in the display window.
yy If you press KEY CHANGER or MIC ECHO
on VOCAL EFFECTS mode, after backing up
current VOCAL EFFECTS, turn off VOCAL
EFFECTS mode and operate KEY CHANGER,
or ECHO mode.
yy If a microphone is not connected, “INSERT
MIC” appears in the display window.
yy To turn off VOCAL EFFECTS mode, press and
hold VOCAL EFFECTS.
4
Operating
yy This function may not be initialized depending
on the status of connected devices.
46 Operating
ECHO
LIGHTING
When you connect your microphone to the MIC jack,
you can give an echo effect to the sound from the
microphones by pressing MIC ECHO on the remote
control or MIC ECHO / DEMO on the unit.
This function offers a party atmosphere by operating
the lighting on the unit.
ECHO 1
ECHO 2
OFF
,,Note
yy If a microphone is not connected, “INSERT
MIC ” appears in the display window.
yy If you press VOCAL EFFECTS button on
ECHO mode, after backing up current ECHO,
turn off ECHO mode and operate VOCAL
EFFECTS mode.
Press MIC ECHO on the remote control or
MIC ECHO / DEMO on the unit again, after
backing up current VOCAL EFFECTS, operate
ECHO mode.
4
Press LIGHTING on the unit.
The mode changes each time you press it:
PARTY WATER FOREST (MY STYLE)
OFF
,,Note
yy Lighting function is available in all functions.
yy Lighting mode retains in its previous mode
when you first press LIGHTING on the unit,
press again to change modes.
yy If you want to use MY STYLE, you have to
register a source with “LG XBOOM” app.
yy Do not look directly at the light emitting part
when the LIGHTING is turned on.
yy If the illumination brightness is glaring, switch
on the room lights or turn off the LIGHTING
of the unit.
Operating
yy You can also turn off the light by pressing and
holding LIGHTING on the unit.
Operating 47
Sleep Timer Setting
Auto power down
Press SLEEP on the remote control repeatedly to
select delay time between 10 and 180 minutes.
After the delay time, the unit will be turned off.
This unit will turn itself off to save electricity in the
case were the main unit is not connected to an
external device and is not used for 15 minutes.
The unit will also turns itself off after six hours if
the main unit has been connected to another device
using the analog inputs.
Auto power down function is applied to only MAIN
unit in case of WIRELESS PARTY LINK connection.
In case of OTHER unit, Auto power down is available
after disconnection OTHER unit and MAIN unit.
To cancel the sleep function, press SLEEP on the
remote control repeatedly until “OFF” appears.
,,Note
yy You can check the remaining time before the
unit is turned off. Press SLEEP on the remote
control to check or change the remaining
time.
yy You can edit the remain time when the
remaining time or “DIMMER” is displayed.
Dimmer
Press SLEEP on the remote control once.
The display window will be darkened by half.
,,Note
All the lighting turns off when Dimmer is being
operated.
This unit automatically turns on and off by an input
source: BT (Bluetooth) or LG TV.
When you turn on your TV connected to this unit,
this unit recognizes the input signal and selects the
suitable function. You can hear the sound from the
unit.
If you try to connect your Bluetooth device, this unit
turns on and connects your Bluetooth device.
You can play your music.
When you turn off this unit by pressing 1 on the
unit for 5 seconds each time, you can turn on or off
the AUTO POWER function.
On Display
Description
ON-AUTO POWER
AUTO POWER function is
turned on.
OFF-AUTO POWER
AUTO POWER function is
turned off.
4
Operating
To cancel it, press SLEEP on the remote control
repeatedly until “OFF” appears.
AUTO POWER On
48 Operating
,,Note
yy Depending on the connected device, this
function may not operate.
yy Depending on the connected device, the unit
turns on but Bluetooth function may not be
connected.
yy If you disconnect Bluetooth connection by
this unit, some Bluetooth devices try to
connect to the unit continually. Therefore it is
recommended to disconnect the connection
before turning off the unit.
yy If you try to connect to the “LG XBOOM” app,
Bluetooth function of this unit is turned on.
yy If you turn on the unit using LG TV or
Bluetooth function, proper function of this
unit is turned on.
yy If you have already paired with this unit,
thisunit can automatically turn on by an input
source when this unit is turned off.
Auto function change
This unit recognizes input signals such as
BT(Bluetooth), LG TV and then automatically
changes to the suitable function.
When you try to connect Bluetooth
device
When you try to connect your Bluetooth device to
this unit, Bluetooth function is selected. Play your
music on the Bluetooth device.
When LG TV is connected
When you turn on your LG TV connected by LG
Sound Sync, this unit changes the function to LG TV.
You can hear the sound from your TV.
,,Note
yy This function is not available during recording
or deleting.
4
yy This function only works with devices that
were previously connected.
Operating
yy If the Bluetooth connection lock function
is set, Bluetooth and LG TV connection will
be only available on Bluetooth and LG TV
function. (Page 37)
Operating 49
Setting the Clock
1. Turn the unit on.
2. Press and hold CLOCK on the remote control.
3. Select time mode by pressing C/V on the
remote control.
- AM 12:00 (for an AM and PM display) or 0:00
(for a 24 hour display)
4. Press SET on the remote control to confirm your
selection.
5. Select the hours by pressing C/V on the
remote control.
6. Press SET on the remote control.
7. Select the minutes by pressing C/V on the
remote control.
8. Press SET on the remote control.
Install “LG XBOOM” app on your Android device.
(Page 38-39)
Your unit’s clock will be automatically synchronized
with your device by activating Bluetooth connection
through “LG XBOOM” app.
1. Turn the unit on.
2. Press and hold ALARM on the remote control.
3. Press C/V on the remote control to change
the hours and minutes and press SET on the
remote control to save.
4. Press C/V on the remote control to select
function and press SET on the remote control to
save.
- Press C/V on the remote control to select
a preset number when you select tuner and
then, press SET on the remote control.
If there is no preset number, this step is skipped.
5. Press C/V on the remote control to change
the volume and press SET on the remote control
to save.
,,Note
yy If you set the clock time, you can check the
time by pressing CLOCK on the remote
control even when the player is turned off.
yy You can set alarm after you set the clock
time.
yy If you set the clock time and alarm, you
can check the alarm setting information by
pressing ALARM on the remote control even
when the unit is turned off.
yy You can select ALARM ON/OFF mode by
pressing ALARM on the remote control.
yy In case of DVD/CD or USB, this function is
available when you have music file. If you do
not have music file, the function is changed
to Tuner.
4
Operating
Setting the Clock through “LG
XBOOM” App
Using your player as an alarm
clock
50 Operating
LG Sound Sync
You can control some functions of this unit by
your TV’s remote control with LG Sound Sync. It is
compatible with LG TV that supports LG Sound Sync.
Make sure your TV has the LG Sound Sync logo.
Controllable function by LG TV’s remote control:
Volume up/down, mute.
Refer to the TV’s instruction manual for the details of
LG Sound Sync.
1. Turn on the unit by pressing 1.
2. Press F until LG TV function is selected.
4
3. Set up the sound output of TV to listen to the
sound through this unit:
TV setting menu [Sound] [TV Sound output]
[LG Sound Sync (Wireless)]
Operating
“PAIRED” appears on the display window for
about 3 seconds and then you can see “LG TV”
on the display window if the TV and this unit are
connected normally.
,,Note
yy You can also use the remote control of this
unit while using LG Sound Sync. If you use TV’s
remote control again, the unit synchronizes
with the TV. (According to TV Specifications,
the volume and mute of this unit synchronize
with TV.)
yy If the connection fails, check the conditions of
this unit and your TV: power, function.
yy Make sure of the condition of this unit and
the connection in the cases below when using
LG Sound Sync.
-- The unit is turned off.
-- Changing to a different function.
-- Disconnecting the wireless connection
caused by interference or a distance.
yy The amount of time to turn off this unit is
different depending on your TV.
yy If you try to change the function on using
the LG TV function, volume will be change
according to the LG TV volume level.
yy Details of TV setting menu vary depending on
models of your TV.
yy If you turned off the unit directly by pressing
1, LG Sound Sync will be disconnected.
To use this function again, you should
reconnect the TV and the unit.
yy The volume may be increased when the TV
and this unit is connected by LG Sound Sync.
Decrease the TV volume and then connect
with this unit.
yy When you turn on your LG TV connected
by LG Sound Sync or enter LG TV function,
this unit changes the function to LG TV
automatically.
yy You should set the TV Sound output manually
depending on the TV version.
yy If you control TV volume when this unit and
TV are connected by LG Sound Sync, this unit
may louder the volume due to synchronizing
volume with TV’s.
Operating 51
WIRELESS PARTY LINK
Connection
You can enjoy the sound by using two speakers.
For enjoying WIRELESS PARTY LINK, you need to
purchase another speaker.
It is compatible with unit that supports WIRELESS
PARTY LINK.
2. Press 3 TWIN on the unit to select MAIN or
OTHER.
- unit: Selects MAIN.
-
unit: Selects OTHER.
Two units try to connect with each other.
3. When these units are successfully connected
to each other, each of connected device names
appears in the each unit.
yy If you using the LG Sound Sync, this function
is not available. If you connect the LG TV
Function, “NOT SUPPORT” appears in the
display window.
yy You can use microphone in the OTHER unit
only. In case of OTHER unit, some functions
are supported only.
yy When WIRELESS PARTY LINK is
disconnected, OTHER unit is changed to
BT(Bluetooth) function.
yy If the connection is failed, “FAILED” appears in
the display window.
yy Mute function is synchronized with each
other.
yy WIRELESS PARTY LINK connection will be
disconnected when you turn off the unit or
press 3 TWIN on the unit.
yy When WIRELESS PARTY LINK is connected,
you can not connect the PARTY LINK with
AUX.
yy Sound of MAIN unit and OTHER unit may be
different depending on playback status or
source.
yy Check the following information when
connecting to Bluetooth.
-- You can connect only one Bluetooth
device in the MAIN unit. You cannot
connect Bluetooth device to the OTHER
unit.
-- WIRELESS PARTY LINK connection is only
supported on Android devices. (WIRELESS
PARTY LINK connection may not be
supported depending on the connected
device specifications or OS.)
-- Removable/detachable Bluetooth
devices (ex. Dongle etc.) will not support
WIRELESS PARTY LINK connection.
-- When WIRELESS PARTY LINK is
connected, Bluetooth connection is not
available in status of recording or deleting.
-- If you connect WIRELESS PARTY
LINK while you are playing connected
Bluetooth device, the unit may be
reconnected again, depending on phone
specification.
4
Operating
1. Press 3 TWIN on the unit.
ROLE SELECT appears in the display window.
,,Note
52 Troubleshooting
Troubleshooting
General
Problem
Cause & Solution
yy Turn off the power of this unit and the connected external device (TV,
Woofer, DVD-player, Amplifier, etc.) and turn it on again.
The unit does not work properly
yy Disconnect the power cord of this unit and the connected external
device (TV, Woofer, DVD-player, Amplifier, etc.) and then try connecting
again.
yy Previous setting may not be saved when device power is shut off.
No power
No picture
5
yy Plug the power cord into the wall outlet securely.
yy Check whether electricity failed.
Check the condition by operating electronic devices using the same
AC outlet.
yy Select the appropriate video input mode on the TV so the picture
from the unit appears on the TV screen.
yy Connect the video cables securely to both the TV and unit.
Troubleshooting
No sound
yy Check whether you select right function.
Press function button and check if you have selected the right
function.
The DVD picture quality is poor
yy Clean the disc using a soft cloth with outward strokes.
A DVD/CD will not play
yy Insert a disc.
yy Insert a playable disc (check the disc type, colour system and
regional code).
Humming noise heard while a DVD or
CD is playing
yy Clean the disc using a soft cloth with outward strokes.
yy Move unit and audio components further away from your TV.
yy Place the disc with the label or printed side facing upwards.
yy Enter your password or change the rating level.
yy The antenna is positioned or connected poorly.
Connect the antenna securely.
Radio stations cannot be tuned in
properly.
yy The signal strength of the radio station is too weak.
Tune to the station manually.
yy No stations have been preset or preset stations have been cleared
(when tuning by scanning preset channels). Preset some radio
stations, see page 40 for details.
yy An unplayable disc is inserted. Check the playable disc.
yy No disc is inserted. Insert a disc.
The unit does not start playback
yy The disc is dirty. Clean the disc. (Page 58)
yy The disc is inserted upside down.
Place the disc with the label or printed side facing upwards.
Troubleshooting 53
Cause & Solution
Problem
yy The remote control is too far from the unit.
Operate the remote control within about 7 m (23 feet).
The remote control does not work
properly.
yy There is an obstacle in the path of the remote control and the unit.
Remove the obstacle.
yy The batteries in the remote control are exhausted.
Replace the batteries with new ones.
No speaker light.
yy Check the light effects by pressing LIGHTING (Page 46).
LG Sound Sync does not work.
yy Check whether your LG TV supports LG Sound Sync.
yy Check connection of LG Sound Sync.
yy Check sound setting of your TV and this unit.
The AUTO POWER function does not
work.
yy Check connection of the external device such as TV or Bluetooth
device.
yy Depending on the connected device, this function may not operate.
NOTES to release Demo mode
Problem
Cause & Solution
Can not change input source with ‘F’ key such as
BT(Bluetooth), USB etc. and only DEMO mode is
Remote Control does not work properly.
Troubleshooting
showing in the display.
5
yy Press ‘DEMO’ Key on the unit for 15 seconds.
54 Appendix
Controlling a TV with
the Supplied Remote
Control
You can control your TV using the buttons below.
By pressing
1 (TV POWER)
Turn the TV on or off.
AV/INPUT
Switch the TV’s input source
between the TV and other
input sources.
,,Note
6
You can
Depending on the unit being connected, you
may not be able to control your TV using some
of the buttons.
Setting up the remote to control
your TV
You can operate your TV with the supplied remote
control.
If your TV is listed in the table below, set the
appropriate manufacturer code.
1. While holding down 1 (TV POWER) on the
remote control, and press the manufacturer code
for your TV with the numerical buttons on the
remote control (see the table below).
Manufacturer
Code Number
LG
1(Default), 2
Zenith
3, 4
GoldStar
1, 2
Samsung
6, 7
Sony
8, 9
Hitachi
4
2. Release the 1 (TV POWER) on the remote
control to complete setting.
Depending on your TV, some or all buttons may not
function on the TV, even after entering the correct
manufacturer code. When you replace the batteries
of the remote, the code number you have set may be
reset to the default setting. Set the appropriate code
number again.
Appendix
Appendix 55
Area Code List
Choose an area code from this list.
Area
Code Area
Code Area
Code Area
Code
Afghanistan
AF
Fiji
FJ
Monaco
MC Singapore
SG
Argentina
AR
Finland
FI
Mongolia
MN Slovak Republic
SK
Australia
AU
France
FR
Morocco
MA Slovenia
SI
Austria
AT
Germany
DE
Nepal
NP
South Africa
ZA
KR
Belgium
BE
Great Britain
GB
Netherlands
NL
South Korea
Bhutan
BT
Greece
GR
Antilles
AN
Spain
ES
Bolivia
BO
Greenland
GL
New Zealand
NZ
Sri Lanka
LK
Brazil
BR
Hong Kong
HK
Nigeria
NG
Sweden
SE
Cambodia
KH
Hungary
HU
Norway
NO
Switzerland
CH
Canada
CA
India
IN
Oman
OM Taiwan
Chile
CL
Indonesia
ID
Pakistan
PK
Thailand
TH
China
CN
Israel
IL
Panama
PA
Turkey
TR
Colombia
CO
Italy
IT
Paraguay
PY
Uganda
UG
Congo
CG
Jamaica
JM
Philippines
PH
Ukraine
UA
Costa Rica
CR
Japan
JP
Poland
PL
United States
US
Croatia
HR
Kenya
KE
Portugal
PT
Uruguay
UY
Czech Republic
CZ
Kuwait
KW Romania
RO
Uzbekistan
UZ
Denmark
DK
Libya
LY
Vietnam
VN
Ecuador
EC
Luxembourg
Zimbabwe
ZW
Egypt
EG
El Salvador
Ethiopia
RU
Malaysia
MY
Saudi Arabia
SA
SV
Maldives
MV Senegal
ET
Mexico
MX
SN
6
Appendix
LU
Russian
Federation
TW
56 Appendix
Language code List
Use this list to input your desired language for the following initial settings: [Disc Audio],
[Disc Subtitle] and [Disc Menu].
6
Language
Code Language
Code Language
Code Language
Code
Afar
6565 French
7082 Lithuanian
7684 Sindhi
8368
Afrikaans
6570 Frisian
7089 Macedonian
7775 Singhalese
8373
Albanian
8381 Galician
7176 Malagasy
7771 Slovak
8375
Ameharic
6577 Georgian
7565 Malay
7783 Slovenian
8376
Arabic
6582 German
6869 Malayalam
7776 Spanish
6983
Armenian
7289 Greek
6976 Maori
7773 Sudanese
8385
Assamese
6583 Greenlandic
7576 Marathi
7782 Swahili
8387
Aymara
6588 Guarani
7178 Moldavian
7779 Swedish
8386
Azerbaijani
6590 Gujarati
7185 Mongolian
7778 Tagalog
8476
Bashkir
6665 Hausa
7265 Nauru
7865 Tajik
8471
Basque
6985 Hebrew
7387 Nepali
7869 Tamil
8465
Bengali; Bangla
6678 Hindi
7273 Norwegian
7879 Telugu
8469
Bhutani
6890 Hungarian
7285 Oriya
7982 Thai
8472
Bihari
6672 Icelandic
7383 Panjabi
8065 Tonga
8479
Breton
6682 Indonesian
7378 Pashto, Pushto
8083 Turkish
8482
Bulgarian
6671 Interlingua
7365 Persian
7065 Turkmen
8475
Burmese
7789 Irish
7165 Polish
8076 Twi
8487
Byelorussian
6669 Italian
7384 Portuguese
8084 Ukrainian
8575
Chinese
9072 Japanese
7465 Quechua
8185 Urdu
8582
8590
Appendix
Croatian
7282 Kannada
7578 Rhaeto-Romance
8277 Uzbek
Czech
6783 Kashmiri
7583 Rumanian
8279 Vietnamese
8673
Danish
6865 Kazakh
7575 Russian
8285 Volapük
8679
Dutch
7876 Kirghiz
7589 Samoan
8377 Welsh
6789
English
6978 Korean
7579 Sanskrit
8365 Wolof
8779
Esperanto
6979 Kurdish
7585 Scots Gaelic
7168 Xhosa
8872
Estonian
6984 Laothian
7679 Serbian
8382 Yiddish
7473
Faroese
7079 Latin
7665 Serbo-Croatian
8372 Yoruba
8979
Fiji
7074 Latvian, Lettish
7686 Shona
8378 Zulu
9085
Finnish
7073 Lingala
7678
Appendix 57
Trademarks and
Licenses
All other trademarks are trademarks of their
respective owners.
Manufactured under license from Dolby
Laboratories. Dolby, Dolby Audio, and the double-D
symbol are trademarks of Dolby Laboratories.
Notes on Copyrights
yy This product incorporates copyright protection
technology that is protected by U.S. patents
and other intellectual property rights. Use of
this copyright protection technology must be
authorized by Rovi, and is intended for home and
other limited viewing uses only unless otherwise
authorized by Rovi. Reverse engineering or
disassembly is prohibited.
yy Under the U.S. Copyright laws and Copyright
laws of other countries, unauthorized recording,
use, display, distribution, or revision of television
programs, videotapes, BD-ROM discs, DVDs, CDs
and other materials may subject you to civil and/or
criminal liability.
The terms HDMI and HDMI High-Definition
Multimedia Interface, and the HDMI logo are
trademarks or registered trademarks of HDMI
Licensing LLC in the United States and other
countries.
“DVD Logo” is a trademark of DVD Format/Logo
Licensing Corporation.
6
Other trademarks and trade names are those of
their respective owners.
Appendix
The Bluetooth® word mark and logos are
registered trademarks owned by the Bluetooth
SIG, Inc. and any use of such marks by LG
Electronics is under license.
58 Appendix
Maintenance
Handling the Unit
When shipping the unit
Notes on Discs
Handling Discs
Never stick paper or tape on the disc.
Storing Discs
Please save the original shipping carton and packing
materials. If you need to ship the unit, for maximum
protection, re-pack the unit as it was originally
packed at the factory.
Keeping the exterior surfaces clean
After playing, store the disc in its case. Do not
expose the disc to direct sunlight or sources of heat
and never leave it in a parked car exposed to direct
sunlight.
Do not use volatile liquids such as insecticide spray
near the unit. Wiping with strong pressure may
damage the surface. Do not leave rubber or plastic
products in contact with the unit for a long period of
time.
Cleaning Discs
Cleaning the unit
Fingerprints and dust on the disc can cause poor
picture quality and sound distortion. Before playing,
clean the disc with a clean cloth. Wipe the disc from
the center to out.
To clean the player, use a soft, dry cloth. If the
surfaces are extremely dirty, use a soft cloth lightly
moistened with a mild detergent solution. Do not use
strong solvents such as alcohol, benzine, or thinner,
as these might damage the surface of the unit.
Do not use strong solvents such as alcohol, benzine,
thinner, commercially available cleaners, or anti-static
spray intended for old vinyl records.
Maintaining the Unit
The unit is a high-tech, precision device. If the optical
pick-up lens and disc drive parts are dirty or worn, the
picture quality could be diminished. For details, please
contact your nearest authorized service center.
6
Appendix
Appendix 59
Specifications
General
Power requirements
Refer to the main label.
Power consumption
Refer to the main label.
Dimensions (W x H x D)
Approx. 451.5 mm x 317.0 mm x 305.5 mm
Operating temperature
5 °C to 35 °C
Operating humidity
5 % to 60 % RH
Inputs/ Outputs
Analog audio in (AUX IN)
600 mV, 600 Ω, RCA jack (L, R) x 1
Analog audio out (AUX OUT)
2.0 Vrms (1 kHz, 0 dB), 600 Ω, RCA jack (L, R) x 1
HDMI OUT (video/audio)
19 pin (Type A, HDMI™ Connector ) x 1
Microphone (MIC)
Sensitivity 20 mV (1 kHz), 6.3 mm jack x 1
Tuner
FM Tuning Range
87.5 to 108.0 MHz or 87.50 to 108.00 MHz
System
Frequency response
80 to 18,000 Hz
Signal-to-noise ratio
More than 75 dB
Dynamic range
More than 80 dB
Bus Power Supply (USB)
5 V 0 500 mA
6
Front
220 W (3 Ω at 1 kHz, THD 25 %)
yy Design and specifications are subject to change without notice.
Appendix
Amplifier (RMS Output power)
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising