LG | 75SM8610 | User manual | LG 75SM8610 Příručka uživatele

LG 75SM8610 Příručka uživatele
OWNER’S MANUAL
Safety and Reference
LED TV*
* LG LED TV applies LCD screen with LED backlights.
Please read this manual carefully before operating your
set and retain it for future reference.
*MFL71040005*
(1907-REV03)
www.lg.com
Copyright © 2019 LG Electronics Inc. All Rights Reserved.
_index
ENGLISH
Warning! Safety
instructions
CAUTION
RISK OF ELECTRIC
SHOCK
DO NOT OPEN
CAUTION : TO REDUCE THE RISK OF ELECTRIC
SHOCK, DO NOT REMOVE COVER (OR BACK).
NO USER-SERVICEABLE PARTS INSIDE. REFER
TO QUALIFIED SERVICE PERSONNEL.
This symbol is intended to alert the
user to the presence of uninsulated
“dangerous voltage” within the product’s
enclosure that may be of sufficient
magnitude to constitute a risk of electric
shock to persons.
This symbol is intended to alert the
user to the presence of important
operating and maintenance (servicing)
instructions in the literature accompanying
the appliance.
WARNING : TO REDUCE THE RISK OF FIRE
AND ELECTRIC SHOCK, DO NOT EXPOSE THIS
PRODUCT TO RAIN OR MOISTURE.
•• TO PREVENT THE SPREAD OF FIRE, KEEP
CANDLES OR OTHER ITEMS WITH OPEN
FLAMES AWAY FROM THIS PRODUCT AT ALL
TIMES.
2
•• Do not place the TV and/or remote
control in the following environments:
--Keep the product away from direct
sunlight.
--An area with high humidity such as a
bathroom
--Near any heat source such as stoves and
other devices that produce heat.
--Near kitchen counters or humidifiers where
they can easily be exposed to steam or oil.
--An area exposed to rain or wind.
--Do not expose to dripping or splashing and
do not place objects filled with liquids,
such as vases, cups, etc. on or over the
apparatus (e.g., on shelves above the unit).
--Near flammable objects such as gasoline
or candles, or expose the TV to direct air
conditioning.
--Do not install in excessively dusty places.
Otherwise, this may result in fire, electric
shock, combustion/explosion, malfunction
or product deformation.
_index
•• Disconnecting the Device from the
Main Power
--The power plug is the disconnecting
device. In case of an emergency, the power
plug must remain readily accessible.
•• Do not let your children climb or cling onto
the TV. Otherwise, the TV may fall over,
which may cause serious injury.
•• Outdoor Antenna Grounding (Can differ
by country):
--If an outdoor antenna is installed, follow
the precautions below.
An outdoor antenna system should not
be located in the vicinity of overhead
power lines or other electric light or power
circuits, or where it can come in contact
with such power lines or circuits as death
or serious injury can occur.
Be sure the antenna system is grounded to
provide some protection against voltage
surges and built-up static charges.
Section 810 of the National Electrical Code
(NEC) in the U.S.A. provides information
with respect to proper grounding of the
mast and supporting structure, grounding
of the lead-in wire to an antenna discharge
unit, size of grounding conductors, location
of antenna discharge unit, connection to
grounding electrodes and requirements for
the grounding electrode.
Antenna grounding according to the
National Electrical Code, ANSI/NFPA 70
ENGLISH
•• Ventilation
--Install your TV where there is proper
ventilation. Do not install in a confined
space such as a bookcase.
--Do not install the product on a carpet or
cushion.
--Do not block or cover the product with
cloth or other materials while unit is
plugged in.
•• Take care not to touch the ventilation
openings. When watching the TV for a
long period, the ventilation openings may
become hot.
•• Protect the power cord from physical or
mechanical abuse, such as being twisted,
kinked, pinched, closed in a door, or walked
upon. Pay particular attention to plugs, wall
outlets, and the point where the cord exits
the device.
•• Do not move the TV whilst the Power cord is
plugged in.
•• Do not use a damaged or loosely fitting
power cord.
•• Be sure do grasp the plug when unplugging
the power cord. Do not pull on the power
cord to unplug the TV.
•• Do not connect too many devices to the
same AC power outlet as this could result in
fire or electric shock.
3
_index
ENGLISH
4
•• Grounding (Except for devices which are
not grounded.)
--TV with a three-prong grounded AC plug
must be connected to a three-prong
grounded AC outlet. Ensure that you
connect the earth ground wire to prevent
possible electric shock.
•• Never touch this apparatus or antenna
during a lightning storm. You may be
electrocuted.
•• Make sure the power cord is connected
securely to the TV and wall socket if not
secured damage to the Plug and socket may
occur and in extreme cases a fire may break
out.
•• Do not insert metallic or inflammable
objects into the product. If a foreign object is
dropped into the product, unplug the power
cord and contact the customer service.
•• Do not touch the end of the power
cord while it is plugged in. You may be
electrocuted.
•• If any of the following occur, unplug
the product immediately and contact
your local customer service.
--The product has been damaged.
--If water or another substance enters the
product (like an AC adapter, power cord,
or TV).
--If you smell smoke or other odors coming
from the TV
--When lightning storms or when unused for
long periods of time.
Even the TV is turned off by remote control
or button, AC power source is connected to
the unit if not unplugged in.
•• Do not use high voltage electrical equipment
near the TV (e.g., a bug zapper). This may
result in product malfunction.
•• Do not attempt to modify this product in
any way without written authorization from
LG Electronics. Accidental fire or electric
shock can occur. Contact your local customer
service for service or repair. Unauthorized
modification could void the user’s authority
to operate this product.
_index
•• Moving
--When moving, make sure the product
is turned off, unplugged, and all cables
have been removed. It may take 2 or more
people to carry larger TVs. Do not press
or put stress on the front panel of the
TV. Otherwise, this may result in product
damage, fire hazard or injury.
•• Keep the packing anti-moisture material or
vinyl packing out of the reach of children.
•• Do not allow an impact shock, any objects
to fall into the product, and do not drop
anything onto the screen.
•• Do not press strongly upon the panel with
a hand or a sharp object such as a nail,
pencil, or pen, or make a scratch on it. It may
cause damage to screen.
•• Cleaning
--When cleaning, unplug the power cord
and wipe gently with a soft/dry cloth. Do
not spray water or other liquids directly
on the TV. Do not clean your TV with
chemicals including glass cleaner, any type
of air freshener, insecticide, lubricants,
wax (car, industrial), abrasive, thinner,
benzene, alcohol etc., which can damage
the product and/or its panel. Otherwise,
this may result in electric shock or product
damage.
ENGLISH
•• Use only an authorized attachments /
accessories approved by LG Electronics.
Otherwise, this may result in fire, electric
shock, malfunction, or product damage.
•• Never disassemble the AC adapter or power
cord. This may result in fire or electric shock.
•• Handle the adapter carefully to avoid
dropping or striking it. An impact could
damage the adapter.
•• To reduce the risk of fire or electrical shock,
do not touch the TV with wet hands. If the
power cord prongs are wet or covered with
dust, dry the power plug completely or wipe
dust off.
•• Batteries
--Store the accessories (battery, etc.) in a
safe location out of the reach of children.
--Do not short circuit, disassemble, or allow
the batteries to overheat. Do not dispose of
batteries in a fire. Batteries should not be
exposed to excessive heat.
5
Preparing
_index
ENGLISH
•• If the TV is turned on for the first time after it
was shipped from the factory, initialization
of the TV may take a few minutes.
•• Image shown may differ from your TV.
•• Your TV’s OSD (On Screen Display) may differ
slightly from that shown in this manual.
•• The available menus and options may differ
from the input source or product model that
you are using.
•• New features may be added to this TV in the
future.
•• The device must be easily accessed to a
location outlet near the access. Some devices
are not made by turning on / off button,
turning off the device and unplugging the
power cord.
•• The items supplied with your product may
vary depending on the model.
•• Product specifications or contents of this
manual may be changed without prior
notice due to upgrade of product functions.
•• For an optimal connection, HDMI cables
and USB devices should have bezels less
than 10 mm thick and 18 mm width. Use an
extension cable that supports
if the
USB cable or USB memory stick does not fit
into your TV’s USB port.
B
B
A
6
A
*A <
= 10 mm
*B <
= 18 mm
•• Use a certified cable with the HDMI logo
attached.
•• If you do not use a certified HDMI cable,
the screen may not display or a connection
error may occur. (Recommended HDMI Cable
Types)
--Ultra High-Speed HDMI®/TM cable (3 m or
less)
Separate Purchase
Wall Mounting Bracket
AN-MR19BA
Check whether your TV model supports
Bluetooth in the Wireless Module Specification
to verify whether it can be used with the Magic
Remote.
Model
VESA (A x B)
(mm)
Standard
screw
Number of
screws
Wall mount
bracket
Model
VESA (A x B)
(mm)
Standard
screw
Number of
screws
Wall mount
bracket
49SM80*
49SM82*
49SM85*
49SM86*
49SM90*
55SM80*
55SM82*
55SM85*
55SM86*
55SM90*
200 x 200
300 x 300
M6
M6
4
4
LSW240B
MSW240
65SM80*
65SM82*
65SM85*
65SM86*
65SM90*
55/65SM98*
OLW480B
MSW240
300 x 300
600 x 400
M6
M8
4
4
OLW480B
LSW640B
_index
Magic Remote Control
ENGLISH
Make sure to use screws and wall mount
Separate purchase items can be changed or
bracket that meet the VESA standard. Standard
modified for quality improvement without any
dimensions for the wall mount kits are
notification. Contact your dealer to buy these
described in the following table.
items. These devices only work with certain
models.
A
B
The model name or design may be changed
depending on the upgrade of product functions,
manufacturer’s circumstances or policies.
75SM86*
75/86SM90*
7
_index
ENGLISH
Lifting and moving
the TV
Please note the following advice to prevent the
TV from being scratched or damaged and for
safe transportation regardless of its type and
size.
•• It is recommended to move the TV in the box
or packing material that the TV originally
came in.
•• Before moving or lifting the TV, disconnect
the power cord and all cables.
•• When holding the TV, the screen should face
away from you to avoid damage.
•• Hold the top and bottom of the TV frame
firmly. Make sure not to hold the transparent
part, speaker, or speaker grill area.
8
•• When transporting a large TV, there should
be at least 2 people.
•• When transporting the TV by hand, hold the
TV as shown in the following illustration.
•• When transporting the TV, do not expose the
TV to jolts or excessive vibration.
•• When transporting the TV, keep the TV
upright, never turn the TV on its side or tilt
towards the left or right.
•• Do not apply excessive pressure to cause
flexing / bending of frame chassis as it may
damage screen.
•• When handling the TV, be careful not to
damage the protruding buttons.
•• Avoid touching the screen at all times,
as this may result in damage to the
screen.
•• When attaching the stand to the TV
set, place the screen facing down on
a cushioned table or flat surface to
protect the screen from scratches.
Mounting on a Table
10 cm
10 cm
10 cm
10 cm
(Depending on model)
2 Connect the power cord to a wall outlet.
_index
10 cm
ENGLISH
1 Lift and tilt the TV into its upright position on
a table.
• Leave a 10 cm (minimum) space from the
wall for proper ventilation.
•• Do not apply foreign substances (oils,
lubricants, etc.) to the screw parts
when assembling the product. (Doing
so may damage the product.)
•• If you install the TV on a stand, you
need to take actions to prevent the
product from overturning. Otherwise,
the product may fall over, which may
cause injury.
•• Do not use any unapproved items to
ensure the safety and product life span.
•• Any damage or injuries caused by using
unapproved items are not covered by
the warranty.
•• Make sure that the screws are inserted
correctly and fastened securely. (If
they are not fastened securely enough,
the TV may tilt forward after being
installed.) Do not use too much force
and over tighten the screws; otherwise
screw may be damaged and not
tighten correctly.
9
Securing TV to the Wall
_index
ENGLISH
(Depending on model)
1 Insert and tighten the eye-bolts, or TV
brackets and bolts on the back of the TV.
• If there are bolts inserted at the eye-bolts
position, remove the bolts first.
2 Mount the wall brackets with the bolts to the
wall. Match the location of the wall bracket
and the eye-bolts on the rear of the TV.
3 Connect the eye-bolts and wall brackets
tightly with a sturdy rope. Make sure to keep
the rope horizontal with the flat surface.
•• Use a platform or cabinet that is strong and
large enough to support the TV securely.
•• Brackets, bolts and ropes are not provided.
You can obtain additional accessories from
your local dealer.
10
Mounting to the Wall
Attach an optional wall mount bracket at the
rear of the TV carefully and install the wall
mount bracket on a solid wall perpendicular
to the floor. When you attach the TV to other
building materials, please contact qualified
personnel. LG recommends that wall mounting
be performed by a qualified professional
installer. We recommend the use of LG’s wall
mount bracket. LG’s wall mount bracket is
easy to move with cables connected. When
you do not use LG’s wall mount bracket, please
use a wall mount bracket where the device is
adequately secured to the wall with enough
space to allow connectivity to external devices.
It is advised to connect all the cables before
installing fixed wall mounts.
10 cm
10 cm
m
10 c
10 cm
10 cm
(Depending on model)
_index
ENGLISH
•• Remove the stand before installing the
TV on a wall mount by performing the
stand attachment in reverse.
•• For more information of screws and
wall mount bracket, refer to the
Separate Purchase.
•• If you intend to mount the product to
a wall, attach VESA standard mounting
interface (optional parts) to the back
of the product. When you install the
set to use the wall mounting bracket
(optional parts), fix it carefully so as
not to drop.
•• When mounting a TV on the wall, make
sure not to install the TV by hanging
the power and signal cables on the
back of the TV.
•• Do not install this product on a wall if it
could be exposed to oil or oil mist. This
may damage the product and cause it
to fall.
(Depending on model)
•• Do not use a sharp object when you
detached the cable cover. This could
damage the cable or the cabinet.
It may also cause personal harm.
(Depending on model)
11
_index
ENGLISH
•• When installing the wall mounting bracket,
it is recommended to cover the stand hole
using tape, in order to prevent the influx of
dust and insects. (Depending on model)
Stand hole
Antenna/Cable
Connect the TV to a wall antenna socket with an
RF cable (75 Ω).
•• Use a signal splitter to use more than 2 TVs.
•• If the image quality is poor, install a signal
amplifier properly to improve the image
quality.
•• If the image quality is poor with an antenna
connected, try to realign the antenna in the
correct direction.
•• An antenna cable and converter are not
supplied.
•• For a location that is not supported with
ULTRA HD broadcasting, this TV cannot
receive ULTRA HD broadcasts directly.
Satellite dish
Connections
Connect the TV to a satellite dish to a satellite
socket with a satellite RF cable (75 Ω).
(Depending on model)
Connect various external devices to the TV and
switch input modes to select an external device.
CI module
For more information of external device’s
View the encrypted (pay) services in digital TV
connection, refer to the manual provided with
mode. (Depending on model)
each device.
•• Check if the CI module is inserted into the
PCMCIA card slot in the right direction. If
the module is not inserted properly, this can
cause damage to the TV and the PCMCIA
card slot.
•• If the TV does not display any video and
audio when CI+ CAM is connected, please
contact to the Terrestrial/Cable/Satellite
Service Operator.
12
Other connections
USB
_index
External Devices
ENGLISH
Some USB Hubs may not work. If a USB device
Connect your TV to external devices. For the
connected using a USB Hub is not detected,
best picture and audio quality, connect the
external device and the TV with the HDMI cable. connect it to the USB port on the TV directly.
Some separate cable is not provided.
HDMI
Available external devices are: Blu-ray player,
HD receivers, DVD players, VCRs, audio systems,
•• When connecting the HDMI cable, the
USB storage devices, PC, gaming devices, and
product and external devices should be
other external devices.
turned off and unplugged.
•• The external device connection may differ
•• Supported HDMI Audio format (Depending
from the model.
on model):
•• Connect external devices to the TV regardless
DTS (44.1 kHz / 48 kHz / 88.2 kHz / 96 kHz),
of the order of the TV port.
DTS HD (44.1 kHz / 48 kHz / 88.2 kHz / 96
•• If you record a TV program on a Blu-ray/DVD
kHz / 176.4 kHz / 192 kHz),
recorder or VCR, make sure to connect the TV
True HD (48 kHz),
signal input cable to the TV through a DVD
Dolby Digital / Dolby Digital Plus (32 kHz /
recorder or VCR. For more information of
44.1 kHz / 48 kHz),
recording, refer to the manual provided with
PCM (32 kHz / 44.1 kHz / 48 kHz / 96 kHz /
the connected device.
192 kHz)
•• Refer to the external equipment’s manual
for operating instructions.
•• →
( ) → [Picture] →
•• If you connect a gaming device to the TV, use
[Additional Settings] → [HDMI ULTRA HD
the cable supplied with the gaming device.
Deep Colour]
•• In PC mode, there may be noise associated
--On: Support 4K @ 50/60 Hz (4:4:4, 4:2:2,
with the resolution, vertical pattern, contrast
4:2:0)
or brightness. If noise is present, change the
--Off: Support 4K @ 50/60 Hz 8 bit (4:2:0)
PC output to another resolution, change the
If the device connected to Input Port also
refresh rate to another rate or adjust the
supports ULTRA HD Deep Colour, your picture
brightness and contrast on the [PICTURE]
may be clearer. However, if the device
menu until the picture is clear.
doesn’t support it, it may not work properly.
•• In PC mode, some resolution settings
In that case, change the TV’s [HDMI ULTRA
may not work properly depending on the
HD Deep Colour] setting to off.
graphics card.
13
_index
ENGLISH
•• If ULTRA HD content is played on your PC,
video or audio may become disrupted
intermittently depending on your PC’s
performance. (Depending on model)
•• When connecting via a wired LAN, it is
recommended to use a CAT 7 cable. (Only
when
port is provided.)
Using Button
You can simply operate the TV functions, using
the button.
Adjusting the menu
When the TV is turned on, press the button
one time. You can adjust the Menu items using
the button.
Turns the power off.
Changes the input source.
Adjusts the volume level.
Scrolls through the saved programmes.
Using Remote Control
Basic functions
Power On (Press)
Power Off1 (Press and Hold)
Menu Control (Press2)
Menu Selection (Press and Hold3)
1 All running apps will close, and any recording
in progress will stop. (Depending on country)
2 You can access and adjust the menu by
pressing the button when TV is on.
3 You can use the function when you access
menu control.
14
(Depending on model)
The descriptions in this manual are based on
the buttons on the remote control. Please read
this manual carefully and use the TV correctly.
To replace batteries, open the battery cover,
replace batteries (1.5 V AAA) matching
the and ends to the label inside the
compartment, and close the battery cover. To
remove the batteries, perform the installation
actions in reverse.
Make sure to point the remote control toward
the remote control sensor on the TV.
To use the button, press and hold for
more than 1 second.
1
1
(Some buttons and services may not be
provided depending on models or regions.)
_index
1
1
ENGLISH
1
(POWER) Turns the TV on or off.
Selects Radio, TV and DTV
programme.
(SEARCH) Search for content such as TV
programmes, movies and other videos, or
perform a web search by entering text in the
search bar.
Recalls your preferred subtitle in
digital mode.
(Q. Settings) Accesses the Quick Settings.
(INPUT) Changes the input source.
Number buttons Enters numbers.
**
Accesses the [QUICK HELP].
Accesses the saved programmes list.
(MORE ACTIONS) Displays more remote
control functions.
**
Edits QUICK ACCESS.
--QUICK ACCESS is a feature that allows you to
enter a specified app or Live TV directly by
pressing and holding the number buttons.
Adjusts the volume level.
Audio descriptions function will be
enabled.
Accesses your favorite channel list.
Shows programme guide.
(MUTE) Mutes all sounds.
**
(MUTE) Accesses the [Accessibility]
menu.
Scrolls through the saved
programmes.
1 Streaming Service buttons Connects to
the Video Streaming Service.
(HOME) Accesses Home menu.
**
(HOME) Shows the previous history.
Set the sleep timer.
Returns to the previous level.
Clears on-screen displays and returns to
TV viewing.
15
_index
ENGLISH
16
Navigation buttons (up/down/left/right)
Scrolls through menus or options.
(OK) Selects menus or options and
confirms your input.
(Teletext buttons) These
buttons are used for teletext.
Starts to record and displays record
menu. (Only Time MachineReady supported
model)
(Energy Saving) Adjusts the brightness
ofthe screen to reduce energy.
(Control buttons) Control
buttons for media contents.
, , ,
These access special
functions in some menus.
Using Magic Remote
Control
(Depending on model)
The descriptions in this manual are based on
the buttons on the remote control. Please read
this manual carefully and use the TV correctly.
When the message [Magic Remote battery is
low. Please change the battery.] is displayed,
replace the battery.
To replace batteries, open the battery cover,
replace batteries (1.5 V AA) matching the
and ends to the label inside the
compartment, and close the battery cover. Be
sure to point the magic remote toward the
remote control sensor on the TV. To remove the
batteries, perform the installation actions in
reverse.
To use the button, press and hold for
more than 1 second.
1
1
(Some buttons and services may not be
provided depending on models or regions.)
_index
1
1
ENGLISH
1
(POWER) Turns the TV on or off.
/ You can turn your set-top box on or
off by adding the set-top box to the universal
remote control for your TV.
Number buttons Enters numbers.
**
Accesses the [QUICK HELP].
(DASH) Inserts a between numbers
such as 2-1 and 2-2.
/
Accesses the saved programmes list.
(MORE ACTIONS) Displays more remote
control functions.
**
Edits QUICK ACCESS
--QUICK ACCESS is a feature that allows you to
enter a specified app or Live TV directly by
pressing and holding the number buttons.
**
Audio descriptions function will be
enabled.
Adjusts the volume level.
(MUTE) Mutes all sounds.
**
(MUTE) Accesses the [Accessibility]
menu.
Scrolls through the saved
programmes.
**
(Voice recognition) Network
connection is required to use the voice
recognition function. Once the voice display
bar is activated on the TV screen, press and
hold the button and speak your command out
loud.
(HOME) Accesses the Home menu.
**
(HOME) Shows the previous history.
(Q. Settings) Accesses the Quick Settings.
**
(Q. Settings) Displays the [All Settings]
menu.
Wheel (OK) Press the center of button
to select a menu. You can change programmes
by using button.
17
_index
ENGLISH
18
(up/down/left/right) Press
the up, down, left or right button to scroll
the menu. If you press
buttons
while the pointer is in use, the pointer will
disappear from the screen and Magic Remote
will operate like a general remote control. To
display the pointer on the screen again, shake
Magic Remote to the left and right.
/
Returns to the previous level.
**
**
/
Clears on-screen displays and
returns to last input viewing.
/
Shows programme guide.
1 Streaming Service buttons Connects to
the Video Streaming Service.
(INPUT) Changes the input source.
**
(INPUT) Accesses the [HOME
DASHBOARD].
Displays the set-top box Home menu.
--When you are not watching via a set-top
box: the display changes to the set-top box
screen.
,
,
,
These access special
functions in some menus.
**
Runs the record function.
, (Control buttons) Controls media
contents.
Registering Magic Remote
Control
How to register the Magic
Remote Control
To use the Magic Remote, first pair it with your
TV.
1 Put batteries into the Magic Remote and turn
the TV on.
2 Point the Magic Remote at your TV and press
the Wheel (OK) on the remote control.
* If the TV fails to register the Magic Remote, try
again after turning the TV off and back on.
How to deregister the Magic
Remote Control
Press the /
and (HOME) buttons
at the same time, for five seconds, to unpair the
Magic Remote with your TV.
* Pressing and holding the
/
button
will let you cancel and reregister Magic
Remote at once.
For more information about this TV, read
the USER GUIDE embedded in the product.
(Depending on model)
•• To open the USER GUIDE → (
) → [General] → [About This TV] → [User
Guide]
Cannot control the TV with the remote control.
•• Check the remote control sensor on the
product and try again.
•• Check if there is any obstacle between the
product and the remote control.
•• Check if the batteries are still working and
properly installed ( to , to ).
No image display and no sound is produced.
•• Check if the product is turned on.
•• Check if the power cord is connected to a
wall outlet.
•• Check if there is a problem in the wall outlet
by connecting other products.
The TV turns off suddenly.
•• Check the power control settings. The power
supply may be interrupted.
•• Check if the auto-off function is activated on
the settings related time.
•• If there is no signal while the TV is on, the TV
will turn off automatically after 15 minutes
of inactivity.
When connecting to the PC (HDMI), no signal is
detected.
•• Turn the TV off/on using the remote control.
•• Reconnect the HDMI cable.
•• Restart the PC with the TV on.
_index
User Guide
Troubleshooting
ENGLISH
•• Do not mix new batteries with old
batteries. This may cause the batteries
to overheat and leak.
•• Failure to match the correct polarities
of the battery may cause the battery to
burst or leak, resulting in fire, personal
injury, or ambient pollution.
•• This apparatus uses batteries. In
your community there might be
regulations that require you to dispose
of these batteries properly due to
environmental considerations. Please
contact your local authorities for
disposal or recycling information.
•• Batteries inside or inside the product
shall not be exposed to excessive heat
such as sunshine, fire or the like.
19
_index
ENGLISH
20
Abnormal Display
•• If the product feels cold to the touch, there
may be a small “flicker” when it is turned on.
This is normal, there is nothing wrong with
product.
•• This panel is an advanced product that
contains millions of pixels. You may see tiny
black dots and/or brightly coloured dots
(red, blue or green) at a size of 1 ppm on the
panel. This does not indicate a malfunction
and does not affect the performance and
reliability of the product. This phenomenon
also occurs in third-party products and is not
subject to exchange or refund.
•• You may find different brightness and colour
of the panel depending on your viewing
position(left/right/top/down).
This phenomenon occurs due to the
characteristic of the panel.
It is not related with the product
performance, and it is not malfunction.
•• Displaying a still image for a prolonged
period of time may cause image sticking.
Avoid displaying a fixed image on the TV
screen for a long period of time.
Generated Sound
•• “Cracking” noise: A cracking noise that
occurs when watching or turning off the TV
is generated by plastic thermal contraction
due to temperature and humidity. This noise
is common for products where thermal
deformation is required.
•• Electrical circuit humming/panel buzzing: A
low level noise is generated from a highspeed switching circuit, which supplies
a large amount of current to operate a
product. It varies depending on the product.
This generated sound does not affect the
performance and reliability of the product.
•• When cleaning the product, be careful
not to allow any liquid or foreign
objects to enter the gap between the
upper, left or right side of the panel
and the guide panel. (Depending on
model)
•• Make sure to wring any excess water or
cleaner from the cloth.
•• Do not spray water or cleaner directly
onto the TV screen.
•• Make sure to spray just enough of
water or cleaner onto a dry cloth to
wipe the screen.
Specifications
Broadcasting Specifications
Television
system
DVB-S/S21
Channel
coverage
(Band)
Maximum
number of
storable
programmes
External antenna
impedance
CI Module (W x
H x D)
950~2150
MHz
DVB-S/S2
DVB-T/T2
DVB-C
DVB-C1
46 ~ 890 MHz
DVB-T/T21
VHF III : 174 ~ 230
MHz
UHF IV : 470 ~ 606
MHz
UHF V : 606 ~ 862
MHz
S Band II : 230 ~
300 MHz
S Band III : 300 ~
470 MHz
6000
_index
Analogue TV
(Depending on
country)
PAL/SECAM B/G,
D/K, I
SECAM L
Digital TV
(Depending on country)
ENGLISH
(Depending on country)
46 ~ 862 MHz
3000
75 Ω
100.0 mm x 55.0 mm x 5.0 mm
1 Only DVB-T2/C/S2 support model only.
21
_index
ENGLISH
Wireless module(LGSBWAC92)Specifications
Wireless LAN (IEEE 802.11a/b/g/n/ac)
Frequency range
Output Power (Max.)
2400 to 2483.5 MHz
18 dBm
5150 to 5725 MHz
18 dBm
5725 to 5850 MHz (Not for EU)
12 dBm
Bluetooth
Frequency range
Output power(Max.)
2400 to 2483.5 MHz
8 dBm
As band channels can vary per country, the user cannot change or adjust the operating
frequency. This product is configured for the regional frequency table.
For consideration of the user, this device should be installed and operated with a minimum
distance of 20 cm between the device and the body.
* IEEE 802.11ac is not available in all countries.
Environment condition
Operating Temperature
Operating Humidity
Storage Temperature
Storage Humidity
22
0 °C to 40 °C
Less than 80 %
-20 °C to 60 °C
Less than 85 %
_index
To obtain the source code under GPL, LGPL,
MPL, and other open source licenses, that is
contained in this product, please visit http://
opensource.lge.com.
In addition to the source code, all referred
license terms, warranty disclaimers and
copyright notices are available for download.
LG Electronics will also provide open source
code to you on CD-ROM for a charge covering
the cost of performing such distribution (such
as the cost of media, shipping, and handling)
upon email request to opensource@lge.com.
This offer is valid for a period of three years after
our last shipment of this product. This offer is
valid to anyone in receipt of this information.
ENGLISH
Open Source
Software Notice
Information
Licenses
(Magic Remote supported models only)
23
SMART TV Quick Setup Guide
* Image shown may differ from your TV.
* Image shown on a PC or mobile phone may vary depending on the OS(Operating System).
* App icon positions may vary on the platform, depending on the software version.
Network Settings
1 Press the (Settings) on the remote to
access the settings menu. Point the
( ) [All
Settings] icon and select by pressing the
Wheel (OK) button on the remote.
4 If the connection is successful, the "[Connected
to Internet]" is displayed.
Picture
CONNECTION
Sound
TV Name
Programmes
Wired Connection (Ethernet)
Not Connected
Connection
Wi-Fi Connection
Connected to Internet
General
Device Connector
Mobile TV on
( )
Safety
All Settings
Accessibility
2 Select the [Connection] → [Wired
Connection(Ethernet)] or [Wi-Fi Connection].
Picture
Sound
Programmes
Picture
TV Name
Sound
Wired Connection (Ethernet)
Programmes
Wi-Fi Connection
Connection
Device Connector
Mobile TV on
Safety
WI-FI CONNECTION
Connection /
Not Connected
General
HDMI Device Settings
You can check the status of connection in [Advanced Wi-Fi settings].
CONNECTION
Not Connected
Connection
Screen Share Settings
General
Add a Hidden Wireless Network
Connect via WPS PBC
Screen Share Settings
Safety
HDMI Device Settings
Connect via WPS PIN
Advanced Wi-Fi Settings
Accessibility
Accessibility
3 The device automatically tries to connect to the
network available (wired network first).
When you select the [Wi-Fi Connection], the
network list available is displayed. Choose the
network you wish to use.
Picture
WI-FI CONNECTION
Connection /
Sound
Programmes
Connection
General
Add a Hidden Wireless Network
Connect via WPS PBC
Safety
Connect via WPS PIN
Advanced Wi-Fi Settings
Accessibility
For wireless AP (Router) that have the
you need to enter the security key.
symbol,
www.lg.com
Troubleshooting Network Problems
1 Press the (Settings) on the remote to
access the settings menu. Point the
( ) [All
Settings] icon and select by pressing the
Wheel (OK) button on the remote.
Check the AP (Router) or consult your Internet
service provider.
When X appears next to Gateway:
( )
1 Unplug the power cord of the AP (Router) and
try to connect after 5 seconds.
All Settings
2 Initialize (Reset) the AP (Router).
2 Select the [Connection] → [Wired Connection
(Ethernet)] or [Wi-Fi Connection] → [Advanced
Wi-Fi Settings].
Picture
CONNECTION
Picture
3 Contact internet service provider or AP (Router)
company.
WI-FI CONNECTION
Connection /
Sound
Sound
TV Name
Programmes
Programmes
Wired Connection (Ethernet)
Not Connected
Connection
Wi-Fi Connection

When X appears next to DNS:
Connection
Not Connected
General
Device Connector
General
Mobile TV on
Safety
Connect via WPS PBC
Safety
Screen Share Settings
Connect via WPS PIN
Advanced Wi-Fi Settings
HDMI Device Settings
Accessibility
Add a Hidden Wireless Network
Accessibility
Follow the instructions below that correlate to your
network status.
Check the TV or the AP (Router).
1 Unplug the power cord of the AP (Router) and
try to connect after 5 seconds.
2 Initialize (Reset) the AP (Router).
3 Check that the MAC address of the TV/AP (Router)
is registered with your Internet service provider.
(The MAC address displayed on the right
pane of the network status window should be
registered with your Internet service provider.)
4 Check the AP (Router) manufacturer’s website
to make sure your router has the latest firmware
version installed.
When X appears next to TV:
1 Check the connection status of the TV, AP
(Router).
2 Power off and power on the TV, AP (Router).
3 If you are using a static IP, enter the IP directly.
4 Contact internet service provider or AP (Router)
company.
SmartShare Connection to Smartphone
1 Check that Wi-Fi is enabled on your smartphone. To use SmartShare, both devices must on the
same local network.
2 Install/run the app for sharing content on your smartphone (It's called LG TV Plus on LG phones).
3 Enable your smartphone to share content files with other devices.
4 Select the file type you want to play (movie, audio or photo).
5 Select a movie, music or photo file to play on the TV.
6 Play the media file to view and enjoy it on your TV.
Updating the TV Firmware
* If the TV is turned on for the first time after it was shipped from the factory, initialization of the TV may
take a few minutes.
1
(Settings) →
(
)[All Settings] →
[General] → [About This TV] → [CHECK FOR UPDATES]
2 After checking the version of the software, update it.
If you check the "[Allow Automatic Updates]", you can update the software automatically.
Picture
Sound
Programmes
GENERAL
AI Service
General
Safety
Accessibility
General /
Software Version
Location
Timers
Account Management
Eco Mode
About This TV
Additional Settings
ABOUT THIS TV
Sound
Language
Time & Date
Connection
Picture
Programmes

Connection
General
Allow Automatic Updates
CHECK FOR UPDATES
TV Information
Notifications
Safety
Accessibility
User Guide
Quick Help
Please call LG Customer Service if you experience any problems.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising