LG | OLED65W9PLA | User manual | LG OLED65W9PLA Příručka uživatele

LG OLED65W9PLA Příručka uživatele
Safety and Reference
Please read this manual carefully before operating
your set and retain it for future reference.
*MFL71182425*
(1909-REV00)
www.lg.com
Copyright
2019 LG Electronics Inc.
All Rights Reserved.
ENGLISH
Warning! Safety
Instructions
CAUTION
RISK OF ELECTRIC
SHOCK
DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF ELECTRIC
SHOCK, DO NOT REMOVE COVER (OR BACK).
NO USER-SERVICEABLE PARTS INSIDE.
REFER TO QUALIFIED SERVICE PERSONNEL.
This symbol is intended to alert the
user to the presence of uninsulated
“dangerous voltage” within the product’s
enclosure that may be of sufficient
magnitude to constitute a risk of electric
shock to persons.
This symbol is intended to alert the
user to the presence of important
operating and maintenance (servicing)
instructions in the literature accompanying
the appliance.
WARNING: TO REDUCE THE RISK OF FIRE
AND ELECTRIC SHOCK, DO NOT EXPOSE THIS
PRODUCT TO RAIN OR MOISTURE.
•• TO PREVENT THE SPREAD OF FIRE, KEEP
CANDLES OR OTHER ITEMS WITH OPEN
FLAMES AWAY FROM THIS PRODUCT AT ALL
TIMES.
2
•• Do not place the TV and/or remote
control in the following environments:
--Keep the product away from direct
sunlight.
--An area with high humidity such as a
bathroom
--Near any heat source such as stoves and
other devices that produce heat.
--Near kitchen counters or humidifiers
where they can easily be exposed to steam
or oil.
--An area exposed to rain or wind.
--Do not expose to dripping or splashing and
do not place objects filled with liquids,
such as vases, cups, etc. on or over the
apparatus (e.g., on shelves above the unit).
--Near flammable objects such as gasoline
or candles, or expose the TV to direct air
conditioning.
--Do not install in excessively dusty places.
Otherwise, this may result in fire, electric
shock, combustion/explosion, malfunction
or product deformation.
•• Disconnecting the Device from the
Main Power
--The power plug is the disconnecting
device. In case of an emergency, the power
plug must remain readily accessible.
•• Do not let your children climb or cling onto
the TV. Otherwise, the TV may fall over,
which may cause serious injury.
•• Outdoor Antenna Grounding (Can differ
by country):
--If an outdoor antenna is installed, follow
the precautions below. An outdoor
antenna system should not be located in
the vicinity of overhead power lines or
other electric light or power circuits, or
where it can come in contact with such
power lines or circuits as death or serious
injury can occur.
Be sure the antenna system is grounded to
provide some protection against voltage
surges and built-up static charges. Section
810 of the National Electrical Code (NEC)
in the U.S.A. provides information with
respect to proper grounding of the mast
and supporting structure, grounding of
the lead-in wire to an antenna discharge
unit, size of grounding conductors, location
of antenna discharge unit, connection to
grounding electrodes and requirements
for the grounding electrode. Antenna
grounding according to the National
Electrical Code, ANSI/NFPA 70
3
ENGLISH
•• Ventilation
--Install your TV where there is proper
ventilation. Do not install in a confined
space such as a bookcase.
--Do not install the product on a carpet or
cushion.
--Do not block or cover the product with
cloth or other materials while unit is
plugged in.
•• Take care not to touch the ventilation
openings. When watching the TV for a
long period, the ventilation openings may
become hot.
•• Protect the power cord from physical or
mechanical abuse, such as being twisted,
kinked, pinched, closed in a door, or walked
upon. Pay particular attention to plugs, wall
outlets, and the point where the cord exits
the device.
•• Do not move the TV whilst the Power cord is
plugged in.
•• Do not use a damaged or loosely fitting
power cord.
•• Be sure do grasp the plug when unplugging
the power cord. Do not pull on the power
cord to unplug the TV.
•• Do not connect too many devices to the
same AC power outlet as this could result in
fire or electric shock.
ENGLISH
4
•• Grounding (Except for devices which are
not grounded.)
--TV with a three-prong grounded AC plug
must be connected to a three-prong
grounded AC outlet. Ensure that you
connect the earth ground wire to prevent
possible electric shock.
•• Never touch this apparatus or antenna
during a lightning storm. You may be
electrocuted.
•• Make sure the power cord is connected
securely to the TV and wall socket if not
secured damage to the Plug and socket may
occur and in extreme cases a fire may break
out.
•• Do not insert metallic or inflammable
objects into the product. If a foreign object is
dropped into the product, unplug the power
cord and contact the customer service.
•• Do not touch the end of the power
cord while it is plugged in. You may be
electrocuted.
•• If any of the following occur, unplug
the product immediately and contact
your local customer service.
--The product has been damaged.
--If water or another substance enters the
product (like an AC adapter, power cord,
or TV).
--If you smell smoke or other odors coming
from the TV
--When lightning storms or when unused for
long periods of time.
Even the TV is turned off by remote control
or button, AC power source is connected to
the unit if not unplugged in.
•• Do not use high voltage electrical equipment
near the TV (e.g., a bug zapper). This may
result in product malfunction.
•• Do not attempt to modify this product in
any way without written authorization from
LG Electronics. Accidental fire or electric
shock can occur. Contact your local customer
service for service or repair. Unauthorized
modification could void the user’s authority
to operate this product.
•• Moving
--When moving, make sure the product
is turned off, unplugged, and all cables
have been removed. It may take 2 or more
people to carry larger TVs. Do not press
or put stress on the front panel of the
TV. Otherwise, this may result in product
damage, fire hazard or injury.
•• Keep the packing anti-moisture material or
vinyl packing out of the reach of children.
•• Do not allow an impact shock, any objects
to fall into the product, and do not drop
anything onto the screen.
•• Do not press strongly upon the panel with
a hand or a sharp object such as a nail,
pencil, or pen, or make a scratch on it. It may
cause damage to screen.
•• Cleaning
--When cleaning, unplug the power cord
and wipe gently with a soft/dry cloth. Do
not spray water or other liquids directly
on the TV. Do not clean your TV with
chemicals including glass cleaner, any type
of air freshener, insecticide, lubricants,
wax (car, industrial), abrasive, thinner,
benzene, alcohol etc., which can damage
the product and/or its panel. Otherwise,
this may result in electric shock or product
damage.
5
ENGLISH
•• Use only an authorized attachments /
accessories approved by LG Electronics.
Otherwise, this may result in fire, electric
shock, malfunction, or product damage.
•• Never disassemble the AC adapter or power
cord. This may result in fire or electric shock.
•• Handle the adapter carefully to avoid
dropping or striking it. An impact could
damage the adapter.
•• To reduce the risk of fire or electrical shock,
do not touch the TV with wet hands. If the
power cord prongs are wet or covered with
dust, dry the power plug completely or wipe
dust off.
•• Batteries
--Store the accessories (battery, etc.) in a
safe location out of the reach of children.
--Do not short circuit, disassemble, or allow
the batteries to overheat. Do not dispose of
batteries in a fire. Batteries should not be
exposed to excessive heat.
Preparing
ENGLISH
6
• If the TV is turned on for the first time after
it was shipped from the factory, initialization
of the TV may take a few minutes.
• Image shown may differ from your TV.
• Your TV’s OSD (On Screen Display) may differ
slightly from that shown in this manual.
• The available menus and options may differ
from the input source or product model that
you are using.
• New features may be added to this TV in the
future.
• The device must be easily accessed to a
location outlet near the access. Some devices
are not made by turning on / off button,
turning off the device and unplugging the
power cord.
• The items supplied with your product may
vary depending on the model.
• Product specifications or contents of this
manual may be changed without prior
notice due to upgrade of product functions.
• For an optimal connection, HDMI cables
and USB devices should have bezels less
than 10 mm thick and 18 mm width. Use an
extension cable that supports
if the
USB cable or USB memory stick does not fit
into your TV’s USB port.
B
B
A
A
*A <
= 10 mm
<
*B = 18 mm
• Use a certified cable with the HDMI logo
attached.
• If you do not use a certified HDMI cable,
the screen may not display or a connection
error may occur. (Recommended HDMI Cable
Types)
-- Ultra High-Speed HDMI®/™ cable (3 m or
less)
Separate Purchase
Please note the following advice to prevent the
TV from being scratched or damaged and for
safe transportation regardless of its type and
size.
• It is recommended to move the TV in
the box or packing material that the TV
originally came in.
• Before moving or lifting the TV, disconnect
the power cord and all cables.
• When holding the TV, the screen should
face away from you to avoid damage.
Magic Remote Control
AN-MR19BA
Check whether your TV model supports
Bluetooth in the Wireless Module Specification
to verify whether it can be used with the Magic
Remote.
Companion Box (AV box)
Wall mount
• Hold the top and bottom of the TV frame
firmly. Make sure not to hold the transparent
part, speaker, or speaker grill area.
W7AWB
7
ENGLISH
Separate purchase items can be changed or
modified for quality improvement without any
notification. Contact your dealer to buy these
items. These devices only work with certain
models.
The model name or design may be changed
depending on the upgrade of product functions,
manufacturer’s circumstances or policies.
The manufacturer shall not be held responsible
for any injuries, damages, or quality issues that
may arise if an item that is not listed below is
purchased separately and used.
Lifting and moving
the TV
ENGLISH
• When transporting a large TV, there should
be at least 2 people.
• When transporting the TV by hand, hold
the TV as shown in the following illustration.
• When transporting the TV, do not expose
the TV to jolts or excessive vibration.
• When transporting the TV, keep the TV
upright, never turn the TV on its side or tilt
towards the left or right.
• Do not apply excessive pressure to cause
flexing / bending of frame chassis as it may
damage screen.
• When handling the TV, be careful not to
damage the protruding buttons.
8
• Avoid touching the screen at all times,
as this may result in damage to the
screen.
• When supported cable is not long
enough to connect TV set with
Companion Box (AV Box), you can use
an extension cable.
• Please do not pile the stuff up or press
strongly the speaker. This may result in
product damage or degradation.
Mounting to the Wall
Wall Material
Concrete
Brick
Natural stone
Provided item
Metal Panel
Wall mount
Punching Guide
Wall mounting screw
Ø5 x L65
Wall mounting
anchor
Plywood
EPS Panel
Plasterboard +
Plywood
Tools
Wall Width
Wall
mounting
anchor, Wall
mounting 70 mm
screw,
Ø 3/6/8 mm
Drill bit
30 mm
Wall
Penetrate
mounting
the wall
screw, Ø 1.8
mm Drill bit 30 mm
Wall mounting screw
for wood
Ø3 x L18
9
ENGLISH
When you attach the TV to other building
materials, please contact qualified personnel.
•• Check the material of the wall and the
thickness of the finishing.
•• Use the Wall mount anchor for wall material
of concrete, light concrete, strong natural
stone, soft natural stone masonry brick and
hallow block that do not crack.
ENGLISH
•• When installing on a gypsum board or
medium-density fiberboard (MDF) wall,
fasten the screws to the studs that support
the wall. If there are no studs, check
the distance from the inner wall before
installing.
--30 mm or below: Install directly on the
inner wall using a 65 mm screw.
--30 mm or above: Install using a separate
hanger.
Wall
•• When installing the wall mount, check the
positions of the wooden studs using a stud
finder. Then, fasten the screws on at least
two separate studs before proceeding.
Stud
Tools you will need
•• Phillips head + driver (manual or
motorized), Ø 3/6/8 mm Drill bit,
Level, Stud finder, Drill
How to attach to masonry
walls
Please follow the below direction.
1 Use a drill bit Ø 8 mm to drill a hole for the
anchor location within a depth of 80 mm
to 100 mm.
2 Clean the drilled hole.
3 Insert the sealed wall mounting anchor to
the hole. (When inserting the anchor, use
a hammer.)
Wall mount
•• When installing the product on wall material
not designated, install the product so that
each location can withstand the pull out
load of 70 kgf (686 N) and shear load of 100
kgf (980 N) or above.
•• Use the Ø 8 mm drill bit for concrete and
hammer (Impact) drill.
Wall mounting anchor
4 Set the wall mount on the wall by aligning
to the location of the hole. And, set the
angle adjusting part to face upward.
Wall mount
10
Wall mounting screw
• When mounting a TV on the wall,
make sure not to install the TV
by hanging the power and signal
cables on the back of the TV.
• Do not install this product on a wall
if it could be exposed to oil or oil
mist. This may damage the product
and cause it to fall.
• Make sure that children do not
climb on or hang on the TV.
• Use a platform or cabinet that is
strong and large enough to support
the TV securely.
• When installing the product,
first check that the wall is strong
enough. Use the anchors and screws
provided.
--If you use anchors and screws
that are not specified by the
manufacturer, they may not
hold the weight of the product,
causing safety issues.
• Be sure to use the accessory
cable provided. Otherwise, friction
between the product and the wall
may cause damage to the connector.
11
ENGLISH
5 Align the wall mounting screw to the hole
and tighten it. Then, fasten the screws at
torque of 45 kgf/cm to 60 kgf/cm.
ENGLISH
12
• When drilling holes into the wall,
make sure you use a drill and drill
bit with the specified diameter.
Ensure that you also follow the
instructions regarding the depth of
the holes.
--Otherwise, the product may be
installed incorrectly and cause
safety issues.
• Wear safety gloves when installing
the product. Do not use your bare
hands.
--Otherwise, it may cause personal
injury.
• If some parts of the wall mount
do not touch the wall after it is
attached, use the double-sided tape
included in the accessory box to
stick the mount to the wall.
• If some parts of the wall mount do
not touch the wall after using the
wall mounting screws for wood, use
the remaining screws.
• Be sure to use only the exclusive
wall mounting screws provided as
accessories.
• If you want to connect the TV Cable
is connected to the back panel
partition, please use the enclosed
Punching Guide.
Using the kensington
security system
(Only OLED65W9*)
The Kensington security system connector is
located at the rear of the Companion Box (AV
Box). For more information of installation and
using, refer to the manual provided with the
Kensington security system or visit http://www.
kensington.com.
Connections
Connect various external devices to the TV and
switch input modes to select an external device.
For more information of external device’s
connection, refer to the manual provided with
each device.
Antenna/Cable
Connect the TV to a wall antenna socket with an
RF cable (75 Ω).
• Use a signal splitter to use more than 2 TVs.
• If the image quality is poor, install a signal
amplifier properly to improve the image
quality.
CI module
View the encrypted (pay) services in digital TV
mode. (Depending on model)
• Check if the CI module is inserted into the
PCMCIA card slot in the right direction. If
the module is not inserted properly, this can
cause damage to the TV and the PCMCIA
card slot.
• If the TV does not display any video and
audio when CI+ CAM is connected, please
contact to the Terrestrial/Cable/Satellite
Service Operator.
Other connections
Connect your TV to external devices. For the
best picture and audio quality, connect the
external device and the TV with the HDMI cable.
Some separate cable is not provided.
(Only UHD models)
•
→ ( ) → [Picture] → [Additional
Settings] → [HDMI ULTRA HD Deep Colour]
--On : Support 4K @ 50/60 Hz (4:4:4, 4:2:2,
4:2:0)
--Off : Support 4K @ 50/60 Hz 8 bit (4:2:0)
If the device connected to Input Port also
supports ULTRA HD Deep Colour, your picture
may be clearer. However, if the device
doesn’t support it, it may not work properly.
In that case, change the TV’s [HDMI ULTRA
HD Deep Colour] setting to off.
USB
Some USB Hubs may not work. If a USB device
connected using a USB Hub is not detected,
connect it to the USB port on the TV directly.
13
ENGLISH
• If the image quality is poor with an antenna HDMI
connected, try to realign the antenna in the
• When connecting the HDMI cable, the
correct direction.
product and external devices should be
• An antenna cable and converter are not
turned off and unplugged.
supplied.
• Supported HDMI Audio format :
• For a location that is not supported with
(Depending on model)
ULTRA HD broadcasting, this TV cannot
DTS (44.1 kHz, 48 kHz, 88.2 kHz, 96 kHz),
receive ULTRA HD broadcasts directly.
DTS HD (44.1 kHz, 48 kHz, 88.2 kHz, 96 kHz,
176.4 kHz, 192 kHz),
Satellite dish
True HD (48 kHz),
Connect the TV to a satellite dish to a satellite
Dolby Digital / Dolby Digital Plus (32 kHz,
socket with a satellite RF cable (75 Ω).
44.1 kHz, 48 kHz),
(Depending on model)
PCM (32 kHz, 44.1 kHz, 48 kHz, 96 kHz, 192
kHz)
External Devices
ENGLISH
14
• In PC mode, some resolution settings
may not work properly depending on the
graphics card.
• If ULTRA HD content is played on your
PC, video or audio may become disrupted
intermittently depending on your PC’s
performance. (Depending on model)
• When connecting via a wired LAN, it is
recommended to use a CAT 7 cable. (Only
when
port is provided.)
Available external devices are: Blu-ray player,
HD receivers, DVD players, VCRs, audio systems,
USB storage devices, PC, gaming devices, and
other external devices.
• The external device connection may differ
from the model.
• Connect external devices to the TV
regardless of the order of the TV port.
• If you record a TV program on a Blu-ray/
DVD recorder or VCR, make sure to connect
the TV signal input cable to the TV through
Using Button
a DVD recorder or VCR. For more information
You can simply operate the TV functions, using
of recording, refer to the manual provided
the button.
with the connected device.
• Refer to the external equipment’s manual
for operating instructions.
• If you connect a gaming device to the TV,
use the cable supplied with the gaming
device.
• In PC mode, there may be noise associated
with the resolution, vertical pattern, contrast
or brightness. If noise is present, change
the PC output to another resolution, change
the refresh rate to another rate or adjust
the brightness and contrast on the PICTURE
menu until the picture is clear.
Basic functions
Volume Control
Programmes Control
1 All running apps will close, and any recording
in progress will stop. (Depending on country)
Adjusting the menu
When the TV is turned on, press the button
one time. You can adjust the Menu items using
the button.
Turns the power off.
Accesses the settings menu.
Clears on-screen displays and returns to
TV viewing.
Changes the input source.
(Depending on model)
The descriptions in this manual are based on
the buttons on the remote control. Please read
this manual carefully and use the TV correctly.
When the message [Magic Remote battery is
low. Please change the battery.] is displayed,
replace the battery.
To replace batteries, open the battery
cover, replace batteries (1.5 V AA) matching
the and ends to the label inside the
compartment, and close the battery cover. Be
sure to point the magic remote toward the
remote control sensor on the TV. To remove the
batteries, perform the installation actions in
reverse.
15
ENGLISH
Power On (Press)
Power Off 1 (Press and hold)
Using Magic Remote
Control
To use the button, press and hold for
more than 1 second.
ENGLISH
1
1
1
1
1
(Some buttons and services may not be
provided depending on models or regions.)
16
(POWER) Turns the TV on or off.
/ You can turn your set-top box on or
off by adding the set-top box to the universal
remote control for your TV.
Number buttons Enters numbers.
Accesses the [QUICK HELP].
(DASH) Inserts a between numbers such
as 2-1 and 2-2.
/
Accesses the saved programmes list.
(MORE ACTIONS) Displays more remote
control functions.
Edits QUICK ACCESS.
--QUICK ACCESS is a feature that allows you to
enter a specified app or Live TV directly by
pressing and holding the number buttons.
Audio descriptions function will be
enabled.
Adjusts the volume level.
(MUTE) Mutes all sounds.
(MUTE) Accesses the [Accessibility]
menu.
Scrolls through the saved
programmes.
(Voice recognition) Network connection
is required to use the voice recognition
function. Once the voice display bar is
activated on the TV screen, press and hold the
button and speak your command out loud.
(HOME) Accesses the Home menu.
(HOME) Shows the previous history.
(Q. Settings) Accesses the Quick Settings.
(Q. Settings) Displays the [All Settings]
menu.
Wheel (OK) Press the center of button
to select a menu. You can change programmes
by using button.
Registering Magic Remote
Control
How to register the Magic
Remote Control
To use the Magic Remote, first pair it with your
TV.
1 Put batteries into the Magic Remote and turn
the TV on.
2 Point the Magic Remote at your TV and press
the Wheel (OK) on the remote control.
* If the TV fails to register the Magic Remote,
try again after turning the TV off and back on.
How to deregister the Magic
Remote Control
Press the /
and (HOME) buttons
at the same time, for five seconds, to unpair the
Magic Remote with your TV.
* Pressing and holding the
/
button
will let you cancel and re-register Magic
Remote at once.
17
ENGLISH
(up/down/left/right) Press
the up, down, left or right button to scroll
the menu. If you press
buttons
while the pointer is in use, the pointer will
disappear from the screen and Magic Remote
will operate like a general remote control. To
display the pointer on the screen again, shake
Magic Remote to the left and right.
/
Returns to the previous level.
/
Clears on-screen displays and
returns to last input viewing.
/
Shows programme guide.
1 Streaming Service buttons Connects to
the Video Streaming Service.
(INPUT) Changes the input source.
(INPUT) Accesses the [HOME
DASHBOARD].
Displays the set-top box Home menu.
--When you are not watching via a set-top
box: the display changes to the set-top box
screen.
, , ,
These access special
functions in some menus.
Runs the record function.
, (Control buttons) Controls media
contents.
ENGLISH
• It is recommended that an Access
Point (AP) be located more than 0.2 m
away from the TV. If the AP is installed
closer than 0.2 m, the Magic remote
control may not perform as expected
due to frequency interference.
• Do not mix new batteries with old
batteries. This may cause the batteries
to overheat and leak.
• Failure to match the correct polarities
of the battery may cause the battery
to burst or leak, resulting in fire,
personal injury, or ambient pollution.
• This apparatus uses batteries. In
your community there might be
regulations that require you to
dispose of these batteries properly
due to environmental considerations.
Please contact your local authorities
for disposal or recycling information.
• Batteries inside or inside the product
shall not be exposed to excessive heat
such as sunshine, fire or the like.
User Guide
For more information about this TV, read the
USER GUIDE embedded in the product.
• To open the USER GUIDE → ( )→
[General] → [About This TV] → [User Guide]
18
Troubleshooting
Cannot control the TV with the remote control.
• Check the remote control sensor on the
product and try again.
• Check if there is any obstacle between the
product and the remote control.
• Check if the batteries are still working and
properly installed ( to , to ).
No image display and no sound is produced.
• Check if the product is turned on.
• Check if the power cord is connected to a
wall outlet.
• Check if there is a problem in the wall outlet
by connecting other products.
The TV turns off suddenly.
• Check the power control settings. The
power supply may be interrupted.
• Check if the auto-off function is activated
on the settings related time.
• If there is no signal while the TV is on,
the TV will turn off automatically after 15
minutes of inactivity.
When connecting to the PC (HDMI), no signal is
detected.
• Turn the TV off/on using the remote control.
• Reconnect the HDMI cable.
• Restart the PC with the TV on.
•• A blue light blinks on the front of the
Companion Box (AV Box).
--The TV may have a problem with the
cooling fan or the temperature in the TV
may be too high. Contact an authorized
service center.
•• A magenta light blinks on the front of the
Companion Box (AV Box).
--The TV may have a problem in the moving
speaker. Contact an authorized service
center.
•• An orange light blinks on the front of the
Companion Box (AV Box).
--The cable from panel may not be properly
connected to the Companion Box (AV Box).
Unplug the power cord and reconnect the
cable and then plug the power cord and
press the power button. If it still doesn’t
work after the steps above, contact an
authorized service center.
19
ENGLISH
Abnormal Display
• If the product feels cold to the touch, there
may be a small “flicker” when it is turned on.
This is normal, there is nothing wrong with
product.
• This panel is an advanced product that
contains millions of pixels. You may see
tiny black dots and/or brightly coloured
dots (white, red, blue or green) at a size of
1 ppm on the panel. This does not indicate
a malfunction and does not affect the
performance and reliability of the product.
This phenomenon also occurs in third-party
products and is not subject to exchange or
refund.
• You may find different brightness and
colour of the panel depending on your
viewing position(left/right/top/down).
This phenomenon occurs due to the
characteristic of the panel. It is not related
with the product performance, and it is not
malfunction.
ENGLISH
Generated Sound
• “Cracking” noise: A cracking noise that
occurs when watching or turning off the TV
is generated by plastic thermal contraction
due to temperature and humidity. This noise
is common for products where thermal
deformation is required.
• Electrical circuit humming/panel buzzing: A
low level noise is generated from a highspeed switching circuit, which supplies
a large amount of current to operate a
product. It varies depending on the product.
This generated sound does not affect the
performance and reliability of the product.
• Make sure to wring any excess water
or cleaner from the cloth.
• Do not spray water or cleaner directly
onto the TV screen.
• Make sure to spray just enough of
water or cleaner onto a dry cloth to
wipe the screen.
• To clean the top of the Companion
Box (AV box), spray a soft cloth with
water. Then, wipe the surface so that
the product does not come in direct
contact with water. Next, wipe it
again so that no moisture remains.
20
Specifications
Analogue TV
(Depending on
country)
PAL B/B, PAL
B/G,
PAL D/K, PAL-I,
SECAM B/G,
SECAM D/K,
NTSC-M
Digital TV
(Depending on country)
DVB-T/T2
DVB-C
DVB-S/S2
Television
system
Program
coverage
Maximum
number of
storable
programmes
External
antenna
impedance
CI Module (W
x H x D)
DVB-S/S21
DVB-C1
950 ~ 2150 MHz
46 ~ 890 MHz
DVB-T/T21
VHF III : 174 ~ 230
MHz
UHF IV : 470 ~ 606
MHz
UHF V : 606 ~ 862
MHz
S Band II : 230 ~
300 MHz
S Band III : 300 ~
470 MHz
6,000
46 ~ 862 MHz
3,000
75 Ω
100.0 mm x 55.0 mm x 5.0 mm
1 Only DVB-T2/C/S2 support model only.
21
ENGLISH
Broadcasting Specifications
ENGLISH
Wireless module(LGSBWAC92)Specifications
Wireless LAN (IEEE 802.11a/b/g/n/ac)
Frequency range
Output power(Max.)
2400 to 2483.5 MHz
18 dBm
5150 to 5725 MHz
18 dBm
5725 to 5850 MHz (Not for EU)
12 dBm
Bluetooth
Frequency range
Output power(Max.)
2400 to 2483.5 MHz
8 dBm
As band channels can vary per country, the user cannot change or adjust the operating
frequency. This product is configured for the regional frequency table.
For consideration of the user, this device should be installed and operated with a minimum
distance of 20 cm between the device and the body.
* IEEE 802.11ac is not available in all countries.
Environment condition
Operating Temperature
Operating Humidity
Storage Temperature
Storage Humidity
22
0 °C to 40 °C
Less than 80 %
-20 °C to 60 °C
Less than 85 %
ENGLISH
Open Source
Software Notice
Information
To obtain the source code under GPL, LGPL,
MPL, and other open source licenses, that is
contained in this product, please visit http://
opensource.lge.com.
In addition to the source code, all referred
license terms, warranty disclaimers and
copyright notices are available for download.
LG Electronics will also provide open source
code to you on CD-ROM for a charge covering
the cost of performing such distribution (such
as the cost of media, shipping, and handling)
upon email request to opensource@lge.com.
This offer is valid for a period of three years after
our last shipment of this product. This offer is
valid to anyone in receipt of this information.
Licenses
(Magic Remote supported models only)
23
ENGLISH
Important
Information for
Preventing Image
Retention
OLED is a self-emissive technology, which
brings many significant benefits to image
quality and performance. As with any selfemitting display, it is possible for users of OLED
TVs to experience temporary image retention
under certain conditions, such as when
displaying a static image on the screen for a
long time. LG OLED TVs incorporate dedicated
functions that protect the screen from possible
image retention.
If a static image persists on screen, screen
brightness is automatically reduced in specific
areas of, or across the entire screen. Once the
static image disappears, screen brightness will
automatically return to its prior setting. This is
not a product malfunction.
24
Examples of Images
that may Cause Image
Retention
•• Still images or fixed images containing
certain information that are displayed
uninterrupted on the screen, such as channel
numbers, station logos, program titles, news
or movie subtitles, and headlines.
•• Fixed menu or icons for video game consoles
or broadcasting set-top boxes.
•• Black bars shown on the left, right, top, or
bottom of the screen, such as in images with
a 4:3 or 21:9 ratio.
•• Avoid watching a video displaying an image
as listed above for extended periods of time.
•• Adjust your TV settings as below when
turning on a video exhibiting an image as
listed above for extended periods of time.
--[Picture] → [Picture Mode Settings] →
[Picture Mode] → [Eco]
--[Picture] → [Picture Mode Settings] →
[OLED LIGHT] → Adjust to lower value
--[Picture] → [Additional Settings] →
[OLED Panel Settings] → [Logo Luminance
Adjustment] → [High]
•• Turn off the menu bar of an external device,
such as a set-top box, to prevent long-term
display of the menu bar of such device.
(Please refer to the manual of the applicable
external device for instructions.)
•• Adjust the settings as below when watching
a video constantly showing black bars on the
left, right, top or bottom, in order to remove
the black bars.
--[Picture] → [Aspect Ratio Settings] →
[Aspect Ratio] → [Vertical Zoom] or [AllDirection Zoom]
Information on Functions
Supporting Image Quality
in Relation to Temporary
Image Retention
•• LG OLED TVs provide a feature called Pixel
Refresher, which helps to prevent temporary
image retention.
•• When the accumulated television viewing
time reaches 2,000 hours or more (this is
equivalent to watching TV for five hours
a day over the course of a year), Pixel
Refresher will be automatically activated
once your TV is turned off. When turning off
your TV, a notice will appear on the screen
informing the activation of Pixel Refresher.
This feature will run for an hour while
your TV is turned off. A horizontal line may
appear at the top or bottom of the screen
when the process is almost finished.
•• You may also manually activate Pixel
Refresher via the TV menu: → (
) → [Picture] → [Additional Settings] →
[OLED Panel Settings] → [Pixel Refresher].
•• Whenever you watch your TV for more than
four cumulative hours, Pixel Refresher will
be automatically activated for a few minutes
once your TV is turned off. (Note: Pixel
Refresher will not be activated if the power
cord of your TV is not plugged in or the main
power is off.)
25
ENGLISH
Recommended Measures
for Preventing Image
Retention
SMART TV Quick Setup Guide
* Image shown may differ from your TV.
* Image shown on a PC or mobile phone may vary depending on the OS(Operating System).
* App icon positions may vary on the platform, depending on the software version.
Network Settings
1 Press the (Settings) on the remote to
access the settings menu. Point the
( ) [All
Settings] icon and select by pressing the
Wheel (OK) button on the remote.
4 If the connection is successful, the "[Connected
to Internet]" is displayed.
Picture
CONNECTION
Sound
TV Name
Programmes
Wired Connection (Ethernet)
Not Connected
Connection
Wi-Fi Connection
Connected to Internet
General
Device Connector
Mobile TV on
( )
Safety
All Settings
Accessibility
2 Select the [Connection] → [Wired
Connection(Ethernet)] or [Wi-Fi Connection].
Picture
Sound
Programmes
Picture
TV Name
Sound
Wired Connection (Ethernet)
Programmes
Wi-Fi Connection
Connection
Device Connector
Mobile TV on
Safety
WI-FI CONNECTION
Connection /
Not Connected
General
HDMI Device Settings
You can check the status of connection in [Advanced Wi-Fi settings].
CONNECTION
Not Connected
Connection
Screen Share Settings
General
Add a Hidden Wireless Network
Connect via WPS PBC
Screen Share Settings
Safety
HDMI Device Settings
Connect via WPS PIN
Advanced Wi-Fi Settings
Accessibility
Accessibility
3 The device automatically tries to connect to the
network available (wired network first).
When you select the [Wi-Fi Connection], the
network list available is displayed. Choose the
network you wish to use.
Picture
WI-FI CONNECTION
Connection /
Sound
Programmes
Connection
General
Add a Hidden Wireless Network
Connect via WPS PBC
Safety
Connect via WPS PIN
Advanced Wi-Fi Settings
Accessibility
For wireless AP (Router) that have the
you need to enter the security key.
symbol,
www.lg.com
Troubleshooting Network Problems
1 Press the (Settings) on the remote to
access the settings menu. Point the
( ) [All
Settings] icon and select by pressing the
Wheel (OK) button on the remote.
Check the AP (Router) or consult your Internet
service provider.
When X appears next to Gateway:
( )
1 Unplug the power cord of the AP (Router) and
try to connect after 5 seconds.
All Settings
2 Initialize (Reset) the AP (Router).
2 Select the [Connection] → [Wired Connection
(Ethernet)] or [Wi-Fi Connection] → [Advanced
Wi-Fi Settings].
Picture
CONNECTION
Picture
3 Contact internet service provider or AP (Router)
company.
WI-FI CONNECTION
Connection /
Sound
Sound
TV Name
Programmes
Programmes
Wired Connection (Ethernet)
Not Connected
Connection
Wi-Fi Connection

When X appears next to DNS:
Connection
Not Connected
General
Device Connector
General
Mobile TV on
Safety
Connect via WPS PBC
Safety
Screen Share Settings
Connect via WPS PIN
Advanced Wi-Fi Settings
HDMI Device Settings
Accessibility
Add a Hidden Wireless Network
Accessibility
Follow the instructions below that correlate to your
network status.
Check the TV or the AP (Router).
1 Unplug the power cord of the AP (Router) and
try to connect after 5 seconds.
2 Initialize (Reset) the AP (Router).
3 Check that the MAC address of the TV/AP (Router)
is registered with your Internet service provider.
(The MAC address displayed on the right
pane of the network status window should be
registered with your Internet service provider.)
4 Check the AP (Router) manufacturer’s website
to make sure your router has the latest firmware
version installed.
When X appears next to TV:
1 Check the connection status of the TV, AP
(Router).
2 Power off and power on the TV, AP (Router).
3 If you are using a static IP, enter the IP directly.
4 Contact internet service provider or AP (Router)
company.
SmartShare Connection to Smartphone
1 Check that Wi-Fi is enabled on your smartphone. To use SmartShare, both devices must on the
same local network.
2 Install/run the app for sharing content on your smartphone (It's called LG TV Plus on LG phones).
3 Enable your smartphone to share content files with other devices.
4 Select the file type you want to play (movie, audio or photo).
5 Select a movie, music or photo file to play on the TV.
6 Play the media file to view and enjoy it on your TV.
Updating the TV Firmware
* If the TV is turned on for the first time after it was shipped from the factory, initialization of the TV may
take a few minutes.
1
(Settings) →
(
)[All Settings] →
[General] → [About This TV] → [CHECK FOR UPDATES]
2 After checking the version of the software, update it.
If you check the "[Allow Automatic Updates]", you can update the software automatically.
Picture
Sound
Programmes
GENERAL
AI Service
General
Safety
Accessibility
General /
Software Version
Location
Timers
Account Management
Eco Mode
About This TV
Additional Settings
ABOUT THIS TV
Sound
Language
Time & Date
Connection
Picture
Programmes

Connection
General
Allow Automatic Updates
CHECK FOR UPDATES
TV Information
Notifications
Safety
Accessibility
User Guide
Quick Help
Please call LG Customer Service if you experience any problems.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising